Pull clk updates from Stephen Boyd:
"The clk core gains a new set of APIs that allow drivers to both
acquire clks and prepare and enable them at the same time. This also
comes with devm support so that drivers can make a single call to get
and prepare and enable the clk and have that all undone when their
driver is removed.
Many folks have requested this feature over the years, but we've had
disagreements about how to implement it and if it was worthwhile to
encourage drivers to use such an API.
Now it's here, so let's see how it goes.
I hope that by introducing this API we can identify drivers that would
benefit from further consolidation of clk API usage, possibly by
moving such logic to the bus layer and out of drivers altogether.
Outside of that major API update, we have the usual collection of
driver updates. A few new SoCs are supported, mostly Qualcomm and
Renesas this time around. Then we have the long tail of non-critical
fixes and minor feature additions to various clk drivers.
And finally more clk provider migration to struct clk_parent_data,
reducing boot times in the process.
Summary:
Core:
- devm helpers for clk_get() + clk_prepare() and clk_enable()
New Drivers:
- Support for the camera clock controller in Qualcomm SM8450 and the
display and gpu clock controllers in Qualcomm SM8350
- Add support for the Renesas RZ/Five SoC
Updates:
- Various fixes, new clocks and USB GDSCs are introduced for Qualcomm
IPQ8074
- Fixes to Qualcomm MSM8939 for issues introduced by inheriting the
MSM8916 GCC driver
- Support for a new type of voteable GDSCs used by Qualcomm SC8280XP
PCIe GDSCs
- Qualcomm SC8280XP pipe clocks transitioned to the new phy-mux
implementation
- Qualcomm MSM8996 GCC, RPM clock driver and some clocks in MSM8994
GCC are migrated to use clk_parent_data
- Corrected the topology for Titan (camera) GDSCs on Qualcomm SDM845
and SM8250
- Qualcomm MSM8916 gains more possible frequencies for its GP clocks.
- The GCC and tsens handling on Qualcomm MSM8960 is reworked to mimic
the design in IPQ8074 to allow the GCC driver to probe earlier.
- The regulator based mmcx supply for Qualcomm dispcc and videocc is
dropped, as the only upstream target that adapted this interface
was transitioned several kernel versions ago
- Qualcomm GDSCs found to be enabled at boot will now reflect in the
enable count of the supply, as was done with the regulator supplies
previously
- Correct adc1, nic_media and edma1's parents for NXP i.MX93
- rdiv, mfd values, the return rate in recalc_rate and add more
frequencies in the table for fracn-gppll on i.MX
- Remove Allwinner workaround logic/compatible in fixed factor code
- MediaTek clk driver cleanups
- Add reset support to more MediaTek clk drivers
- deduplicate Allwinner ccu_clks arrays
- Allwinner H6 GPU DFS support
- Adjust Allwinner Kconfig to limit choice
- Fix initconst confusion on Renesas R-Car Gen4
- Add GPT/POEG (PWM) clocks and resets on Renesas RZ/G2L
- Add PFC and WDT clocks and resets on Renesas RZ/V2M
- Add thermal, SDHI, Z (CPU core), PCIe, and HSCIF (serial) clocks on
Renesas R-Car S4-8"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (124 commits)
clk: fixed-factor: Introduce *clk_hw_register_fixed_factor_parent_hw()
clk: mux: Introduce devm_clk_hw_register_mux_parent_hws()
clk: divider: Introduce devm_clk_hw_register_divider_parent_hw()
clk: qcom: gcc-msm8994: use parent_hws for gpll0/4
clk: qcom: clk-rpm: convert to parent_data API
dt-bindings: clock: fix wrong clock documentation for qcom,rpmcc
clk: qcom: gcc-msm8939: Add missing USB HS system clock frequencies
clk: qcom: gcc-msm8939: Add missing MDSS MDP clock frequencies
clk: qcom: gcc-msm8939: Add missing CAMSS CPP clock frequencies
clk: qcom: gcc-msm8939: Fix venus0_vcodec0_clk frequency definitions
clk: qcom: gcc-msm8939: Add missing CAMSS CCI bus clock
clk: qcom: gcc-msm8939: Fix weird field spacing in ftbl_gcc_camss_cci_clk
clk: qcom: gdsc: Bump parent usage count when GDSC is found enabled
clk: qcom: Drop mmcx gdsc supply for dispcc and videocc
clk: qcom: fix build error initializer element is not constant
clk: sprd: Add dt-bindings include file for UMS512
dt-bindings: clk: sprd: Add bindings for ums512 clock controller
clk: sunxi-ng: sun50i: h6: Modify GPU clock configuration to support DFS
dt-bindings: clock: qcom,gcc-msm8996: add more GCC clock sources
clk: qcom: add support for SM8350 DISPCC
...
Pull devicetree updates from Rob Herring:
"Bindings:
- Add spi-peripheral-props.yaml references to various SPI device
bindings
- Convert qcom,pm8916-wdt, ds1307, Qualcomm BAM DMA, is31fl319x,
skyworks,aat1290, Rockchip EMAC, gpio-ir-receiver, ahci-ceva, Arm
CCN PMU, rda,8810pl-intc, sil,sii9022, ps2-gpio, and
arm-firmware-suite bindings to DT schema format
- New bindings for Arm virtual platforms display, Qualcomm IMEM
memory region, Samsung S5PV210 ChipID, EM Microelectronic EM3027
RTC, and arm,cortex-a78ae
- Add vendor prefixes for asrock, bytedance, hxt, ingrasys, inventec,
quanta, and densitron
- Add missing MSI and IOMMU properties to host-generic-pci
- Remove bindings for removed EFM32 platform
- Remove old chosen.txt binding (replaced by schema)
- Treewide add missing type information for properties
- Treewide fixing of typos and its vs. it's in bindings. Its all good
now.
- Drop unnecessary quoting in power related schemas
- Several LED binding updates which didn't get picked up
- Move various bindings to proper directories
DT core code:
- Convert unittest GPIO related tests to use fwnode
- Check ima-kexec-buffer against memory bounds
- Print reserved-memory allocation/reservation failures as errors
- Cleanup early_init_dt_reserve_memory_arch()
- Simplify of_overlay_fdt_apply() tail"
* tag 'devicetree-for-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (65 commits)
dt-bindings: mtd: microchip,mchp48l640: use spi-peripheral-props.yaml
dt-bindings: power: supply: drop quotes when not needed
dt-bindings: power: reset: drop quotes when not needed
dt-bindings: power: drop quotes when not needed
dt-bindings: PCI: host-generic-pci: Allow IOMMU and MSI properties
of/fdt: declared return type does not match actual return type
devicetree/bindings: correct possessive "its" typos
dt-bindings: net: convert emac_rockchip.txt to YAML
dt-bindings: eeprom: microchip,93lc46b: move to eeprom directory
dt-bindings: eeprom: at25: use spi-peripheral-props.yaml
dt-bindings: display: use spi-peripheral-props.yaml
dt-bindings: watchdog: qcom,pm8916-wdt: convert to dtschema
dt-bindings: power: reset: qcom,pon: use absolute path to other schema
dt-bindings: iio/dac: adi,ad5766: Add missing type to 'output-range-microvolts'
dt-bindings: power: supply: charger-manager: Add missing type for 'cm-battery-stat'
dt-bindings: panel: raydium,rm67191: Add missing type to 'video-mode'
of/fdt: Clean up early_init_dt_reserve_memory_arch()
dt-bindings: PCI: fsl,imx6q-pcie: Add missing type for 'reset-gpio-active-high'
dt-bindings: rtc: Add EM Microelectronic EM3027 bindings
dt-bindings: rtc: ds1307: Convert to json-schema
...
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
Pull ARM new SoC support from Arnd Bergmann:
"This adds initial support for two SoC families that have been under
review for a while. In both cases, the origonal idea was to have a
minimally functional version, but we ended up leaving out the clk
drivers that are still under review and will be merged through the
corresponding subsystem tree.
The Nuvoton NPCM8xx is a 64-bit Baseboard Management Controller and
based on the 32-bit NPCM7xx family but is now getting added to
arch/arm64 as well.
Sunplus SP7021, also known as Plus1, is a general-purpose
System-in-Package design based on the 32-bit Cortex-A7 SoC on the main
chip, plus an I/O chip and memory in the same"
* tag 'arm-newsoc-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
MAINTAINERS: rectify entry for ARM/NUVOTON NPCM ARCHITECTURE
arm64: defconfig: Add Nuvoton NPCM family support
arm64: dts: nuvoton: Add initial NPCM845 EVB device tree
arm64: dts: nuvoton: Add initial NPCM8XX device tree
arm64: npcm: Add support for Nuvoton NPCM8XX BMC SoC
dt-bindings: arm: npcm: Add nuvoton,npcm845 GCR compatible string
dt-bindings: arm: npcm: Add nuvoton,npcm845 compatible string
dt-bindings: arm: npcm: Add maintainer
reset: npcm: Add NPCM8XX support
dt-bindings: reset: npcm: Add support for NPCM8XX
reset: npcm: using syscon instead of device data
ARM: dts: nuvoton: add reset syscon property
dt-bindings: reset: npcm: add GCR syscon property
dt-binding: clk: npcm845: Add binding for Nuvoton NPCM8XX Clock
dt-bindings: watchdog: npcm: Add npcm845 compatible string
dt-bindings: timer: npcm: Add npcm845 compatible string
ARM: dts: Add Sunplus SP7021-Demo-V3 board device tree
ARM: sp7021_defconfig: Add Sunplus SP7021 defconfig
ARM: sunplus: Add initial support for Sunplus SP7021 SoC
irqchip: Add Sunplus SP7021 interrupt controller driver
...
Merge the new SoC support from Tomer Maimon:
"This patchset adds initial support for the Nuvoton
Arbel NPCM8XX Board Management controller (BMC) SoC family.
The Nuvoton Arbel NPCM8XX SoC is a fourth-generation BMC.
The NPCM8XX computing subsystem comprises a quadcore ARM
Cortex A35 ARM-V8 architecture.
This patchset adds minimal architecture and drivers such as:
Clocksource, Clock, Reset, and WD.
Some of the Arbel NPCM8XX peripherals are based on Poleg NPCM7XX.
This patchset was tested on the Arbel NPCM8XX evaluation board."
I'm leaving out the clk controller driver, which is still under
review.
* nuvoton/newsoc:
arm64: defconfig: Add Nuvoton NPCM family support
arm64: dts: nuvoton: Add initial NPCM845 EVB device tree
arm64: dts: nuvoton: Add initial NPCM8XX device tree
arm64: npcm: Add support for Nuvoton NPCM8XX BMC SoC
dt-bindings: arm: npcm: Add nuvoton,npcm845 GCR compatible string
dt-bindings: arm: npcm: Add nuvoton,npcm845 compatible string
dt-bindings: arm: npcm: Add maintainer
reset: npcm: Add NPCM8XX support
dt-bindings: reset: npcm: Add support for NPCM8XX
reset: npcm: using syscon instead of device data
ARM: dts: nuvoton: add reset syscon property
dt-bindings: reset: npcm: add GCR syscon property
dt-binding: clk: npcm845: Add binding for Nuvoton NPCM8XX Clock
dt-bindings: watchdog: npcm: Add npcm845 compatible string
dt-bindings: timer: npcm: Add npcm845 compatible string
Qualcomm ARM64 DTS updates for v5.20
This introduces initial support for Lenovo ThinkPad X13s, Qualcomm 8cx
Gen 3 Compute Reference Device, SA8295P Automotive Development Platform,
Xiaomi Mi 5s Plus, five new SC7180 Chrome OS boards, Inforce IFC6560, LG
G7 ThinQ and LG V35 ThinQ.
With IPQ8074 gaining GDSC support, this was expressed in the gcc node
and defined for the USB nodes. The SDHCI reset line was defined to get
the storage devices into a known state.
For MSM8996 interconnect providers, the second DSI interface, resets for
SDHCI are introduced. Support for the Xiaomi Mi 5s Plus is introduced
and the Dragonboard 820c gains definitions for its LEDs.
The MSM8998 platform changes consists of a various cleanup patches, the
FxTec Pro1 is split out from using the MTP dts and Sony Xperia devices
on the "Yoshino" platform gains ToF sensor.
On SC7180 five new Trogdor based boards are added and the description of
keyboard and detachables is improved.
On the SC7280-based Herobrine board DisplayPort is enabled, SPI flash
clock rate is changed, WiFi is enabled and the modem firmware path is
updated. The Villager boards gains touchscreen, and keyboard backlight.
This introduces initial support for the SC8280XP (aka 8cx Gen 3) and
related automotive platforms are introduced, with support for the
Qualcomm reference board, the Lenovo Thinkpad X13s and the SA8295P
Automotive Development Platform.
In addition to a wide range of smaller fixes on the SDM630 and SDM660
platforms, support for the secondary high speed USB controller is
introduced and the Sony Xperia "Nile" platform gains support for the RGB
status LED. Support for the Inforce IFC6560 board is introduced.
On SDM845 the bandwidth monitor for the CPU subsystem is introduced, to
scale LLCC clock rate based on profiling. CPU and cluster idle states
are switched to OSI hierarchical states. DB845c and SHIFT 6mq gains LED
support and new support for the LG G7 ThinQ and LG V35 ThinQ boards are
added.
DLL/DDR configuration for SDHCI nodes are defined for SM6125.
On SM8250 the GPU per-process page tables is enabled and for RB5 the
Light Pulse Generator-based LEDs are added.
The display clock controller is introduced for SM8350.
On SM8450 this introduces the camera clock controller and the UART
typically used for Bluetooth. The interconnect path for the crypto
engine is added to the SCM node, to ensure this is adequately clocked.
The assigned-clock-rate for the display processor is dropped from
several platforms, now that the driver derrives the min and max from the
clock.
In addition to this a wide range of fixes for stylistic issues and
issues discovered through Devicetree binding validation across many
platforms and boards are introduced.
* tag 'qcom-arm64-for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (193 commits)
arm64: dts: qcom: sc8280xp: fix DP PHY node unit addresses
arm64: dts: qcom: sc8280xp: fix usb_0 HS PHY ref clock
arm64: dts: qcom: sc7280: fix PCIe clock reference
docs: arm: index.rst: add google/chromebook-boot-flow
arm64: dts: qcom: msm8996: clean up PCIe PHY node
arm64: dts: qcom: msm8996: use non-empty ranges for PCIe PHYs
arm64: dts: qcom: sm8450: drop UFS PHY clock-cells
arm64: dts: qcom: sm8250: drop UFS PHY clock-cells
arm64: dts: qcom: sc8280xp: drop UFS PHY clock-cells
arm64: dts: qcom: sm8450: drop USB PHY clock index
arm64: dts: qcom: sm8350: drop USB PHY clock index
arm64: dts: qcom: msm8998: drop USB PHY clock index
arm64: dts: qcom: ipq8074: drop USB PHY clock index
arm64: dts: qcom: ipq6018: drop USB PHY clock index
arm64: dts: qcom: sm8250: add missing PCIe PHY clock-cells
arm64: dts: qcom: sc7280: drop PCIe PHY clock index
Revert "arm64: dts: qcom: Fix 'reg-names' for sdhci nodes"
arm64: dts: qcom: sc7180-idp: add vdds supply to the DSI PHY
arm64: dts: qcom: sc7280: use constants for gpucc clocks and power-domains
arm64: dts: qcom: msm8996: add missing DSI clock assignments
...
Link: https://lore.kernel.org/r/20220713203939.1431054-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dt-bindings: Changes for v5.20-rc1
These changes add clock, reset, memory client and power domain
definitions for various devices found on Tegra234 along with a few
device tree bindings for new hardware.
* tag 'tegra-for-5.20-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: tegra-ccplex-cluster: Remove status from required properties
dt-bindings: Add headers for Host1x and VIC on Tegra234
dt-bindings: timer: Add Tegra186 & Tegra234 Timer
dt-bindings: arm: tegra: Add NVIDIA Tegra234 CBB 2.0 binding
dt-bindings: arm: tegra: Add NVIDIA Tegra194 AXI2APB binding
dt-bindings: arm: tegra: Add NVIDIA Tegra194 CBB 1.0 binding
dt-bindings: memory: Add Tegra234 MGBE memory clients
dt-bindings: Add Tegra234 MGBE clocks and resets
dt-bindings: power: Add Tegra234 MGBE power domains
dt-bindings: Add headers for Tegra234 GPCDMA
Link: https://lore.kernel.org/r/20220708185608.676474-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
as is without any warranty of any kind whether express or implied
without even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull clk updates from Stephen Boyd:
"Mainly driver updates this time around.
There's a single patch to the core clk framework that simplifies a
runtime PM call. Otherwise the majority of the diff falls to a few SoC
drivers: Qualcomm, STM32 and MediaTek. Those SoCs gain some new
hardware support and what comes along with that is quite a few lines
of data and some clk_ops code.
Beyond the new hardware support we have the usual pile of driver
updates that add missing clks on already supported SoCs or fix up
problems like bad clk tree descriptions. It's nice to see that more
drivers are moving to clk_hw based APIs too.
New Drivers:
- Add STM32MP13 RCC driver (Reset Clock Controller)
- MediaTek MT8186 SoC clk support
- Airoha EN7523 SoC system clocks
- Clock driver for exynosautov9 SoC
- Renesas R-Car V4H and RZ/V2M SoCs
- Renesas RZ/G2UL SoC
- LPASS clk driver for Qualcomm sc7280 SoC
- GCC clk driver for Qualcomm SC8280XP SoC
Updates:
- SDCC uses floor clk ops on Qualcomm MSM8976
- Add modem reset and fix RPM clks on Qualcomm MSM8976
- Add the two missing CLKOUT clocks for U8500/DB8500 SoC
- Mark some clks critical on Ingenic X1000
- Convert ux500 to clk_hw
- Move MediaTek driver to clk_hw provider APIs
- Use i2c driver probe_new to avoid id scans
- Convert a number of Rockchip dt bindings to YAML
- Mark hclk_vo critical on Rockchip rk3568
- Use pm_runtime_resume_and_get to fix pm_runtime_get_sync() usage
- Various cleanups like memory allocation error checks and plugged
leaks
- Allwinner H6 RTC clock support
- Allwinner H616 32 kHz clock support
- Add the Universal Flash Storage clock on Renesas R-Car S4-8
- Add I2C, SSIF-2 (sound), USB, CANFD, OSTM (timer), WDT, SPI Multi
I/O Bus, RSPI, TSU (thermal), and ADC clocks and resets on Renesas
RZ/G2UL
- Add display clock support on Renesas RZ/G2L
- Add RPC (QSPI/HyperFlash) clocks on Renesas R-Car E3 and D3
- Add 27 MHz phy PLL ref clock on i.MX
- Add mcore_booted module parameter to tell kernel M core has already
booted for i.MX
- Remove snvs clock on i.MX because it was for secure world only
- Add dt bindings for i.MX8MN GPT
- Add DISP2 pixel clock for i.MX8MP
- Add clkout1/2 for i.MX8MP
- Fix parent clock of ubs_root_clk for i.MX8MP
- Implement better RCG parking on Qualcomm SoCs using the shared RCG
clk ops
- Kerneldoc fixes
- Switch Tegra BPMP to determine_rate clk op
- Add a pointer to dt schema for generic clock bindings"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (168 commits)
Revert "clk: qcom: regmap-mux: add pipe clk implementation"
Revert "clk: qcom: gcc-sc7280: use new clk_regmap_mux_safe_ops for PCIe pipe clocks"
Revert "clk: qcom: gcc-sm8450: use new clk_regmap_mux_safe_ops for PCIe pipe clocks"
clk: bcm: rpi: Use correct order for the parameters of devm_kcalloc()
clk: stm32mp13: add safe mux management
clk: stm32mp13: add multi mux function
clk: stm32mp13: add all STM32MP13 kernel clocks
clk: stm32mp13: add all STM32MP13 peripheral clocks
clk: stm32mp13: manage secured clocks
clk: stm32mp13: add composite clock
clk: stm32mp13: add stm32 divider clock
clk: stm32mp13: add stm32_gate management
clk: stm32mp13: add stm32_mux clock management
clk: stm32: Introduce STM32MP13 RCC drivers (Reset Clock Controller)
dt-bindings: rcc: stm32: add new compatible for STM32MP13 SoC
clk: ti: clkctrl: replace usage of found with dedicated list iterator variable
clk: ti: composite: Prefer kcalloc over open coded arithmetic
dt-bindings: clock: exynosautov9: correct count of NR_CLK
clk: mediatek: mt8173: Switch to clk_hw provider APIs
clk: mediatek: Switch to clk_hw provider APIs
...
Pull ARM DT updates from Arnd Bergmann:
"There are 40 branches this time, adding a lot of new hardware support,
and cleanups. Krzysztof Kozlowski continues his treewide cleanups.
There are a number of new SoCs, all of them as part of existing
families, and typically added along with a reference board:
- Renesas RZ/G2UL (R9A07G043) is the single-core version of the
RZ/G2L general-purpose MPU.
- Renesas RZ/V2M (R9A09G011) is a smart camera SoC
- Renesas R-Car V4H (R8A779G0) is an automotive chip with Cortex-A76
cores and deep learning accerlation.
- Broadcom BCM47622 is a new broadband SoC based on a quad Cortex-A7
and dual Wifi-6.
- Corstone1000 is a generic platform from Arm that is used for
designing custom SoCs, the support for now is for the Fixed Virtual
Platform emulation for it.
- Mediatek MT8195 (Kompanio 1200) is a high-end consumer chip used in
upcoming Chromebooks.
- NXP i.MXRT1050 is a Cortex-M7 based microcontroller, the first
MMU-less SoC to be added in a while
New machines based on already supported SoCs this time are mainly for
32-bit platforms and include:
- Two wireless routers based on Broadcom bcm4708
- 30 new boards based on NXP i.MX6, i.MX7 and i.MX8 families, mostly
for the industrial embedded market, and on NXP LS1021A based IOT
board.
- Two ethernet switches based on Microchip LAN966
- Eight Qualcomm Snapdragon based machines, including a smartwatch, a
Chromebook board and some phones
- Another phone based on the old ST-Ericsson Ux500 platform
- Seven STM32MP1 based boards
- Four single-board computers based on Rockchip RK3566/RK3568"
* tag 'arm-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (791 commits)
ARM: dts: kswitch-d10: enable networking
ARM: dts: lan966x: add switch node
ARM: dts: lan966x: add serdes node
ARM: dts: lan966x: add reset switch reset node
ARM: dts: lan966x: add MIIM nodes
ARM: dts: lan966x: add hwmon node
ARM: dts: lan966x: add basic Kontron KSwitch D10 support
ARM: dts: lan966x: add flexcom I2C nodes
ARM: dts: lan966x: add flexcom SPI nodes
ARM: dts: lan966x: add all flexcom usart nodes
ARM: dts: lan966x: add missing uart DMA channel
ARM: dts: lan966x: add sgpio node
ARM: dts: lan966x: swap dma channels for crypto node
ARM: dts: lan966x: rename pinctrl nodes
ARM: dts: at91: sama7g5: remove interrupt-parent from gic node
ARM: dts: at91: use generic node name for dataflash
ARM: dts: turris-omnia: Add atsha204a node
arm64: dts: mt8192: Follow binding order for SCP registers
arm64: dts: mediatek: add mtk-snfi for mt7622
arm64: dts: mediatek: mt8195-demo: enable uart1
...
- Airoha EN7523 SoC system clocks
- Use i2c driver probe_new to avoid id scans
* clk-ti:
clk: ti: clkctrl: replace usage of found with dedicated list iterator variable
clk: ti: composite: Prefer kcalloc over open coded arithmetic
clk: keystone: syscon-clk: Add support for AM62 epwm-tbclk
dt-bindings: clock: ehrpwm: Add AM62 specific compatible
* clk-cleanup:
clk: bcm: rpi: Use correct order for the parameters of devm_kcalloc()
clk: fixed-rate: Remove redundant if statement
clk: mux: remove redundant initialization of variable width
clk: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
clk: actions: remove redundant assignment after a mask operation
* clk-airoha:
clk: en7523: fix wrong pointer check in en7523_clk_probe()
clk: en7523: Add clock driver for Airoha EN7523 SoC
dt-bindings: Add en7523-scu device tree binding documentation
* clk-i2c-simple:
clk: renesas-pcie: use simple i2c probe function
clk: si570: use i2c_match_id and simple i2c probe
clk: si544: use i2c_match_id and simple i2c probe
clk: si5351: use i2c_match_id and simple i2c probe
clk: si5341: use simple i2c probe function
clk: si514: use simple i2c probe function
clk: max9485: use simple i2c probe function
clk: cs2000-cp: use simple i2c probe function
clk: cdce925: use i2c_match_id and simple i2c probe
clk: cdce706: use simple i2c probe function
* clk-renesas: (48 commits)
clk: renesas: r9a09g011: Add eth clock and reset entries
clk: renesas: Add RZ/V2M support using the rzg2l driver
clk: renesas: rzg2l: Add support for RZ/V2M reset monitor reg
clk: renesas: rzg2l: Make use of CLK_MON registers optional
clk: renesas: rzg2l: Set HIWORD mask for all mux and dividers
clk: renesas: rzg2l: Add read only versions of the clk macros
clk: renesas: rzg2l: Move the DEF_MUX array size calc into the macro
dt-bindings: clock: renesas,rzg2l: Document RZ/V2M SoC
clk: renesas: r9a07g044: Fix OSTM1 module clock name
clk: renesas: r9a07g043: Add clock and reset entries for ADC
clk: renesas: r9a07g043: Add TSU clock and reset entry
clk: renesas: r9a07g043: Add RSPI clock and reset entries
clk: renesas: r9a07g043: Add clock and reset entries for SPI Multi I/O Bus Controller
clk: renesas: r9a07g044: Add DSI clock and reset entries
clk: renesas: r9a07g044: Add LCDC clock and reset entries
clk: renesas: r9a07g044: Add M4 Clock support
clk: renesas: r9a07g044: Add M3 Clock support
clk: renesas: r9a07g044: Add {M2, M2_DIV2} Clocks support
clk: renesas: r9a07g044: Add M1 clock support
clk: renesas: rzg2l: Add DSI divider clk support
...
Qualcomm ARM64 DT updates for v5.19
This adds MDIO bus description on the IPQ6018 platform.
On MSM8916 the BAM-DMUX WWAN network device is added and the Huawei
Ascend G7 gains sound card definition and clarified installation
instructions.
MSM8992 and MSM8994 continues to be worked on, gaining multimedia clock
controller, on-chip memory, watchdog and various cleanup changes. The
Xiaomi Mi 4C gains CPU regulators and fixes to the framebuffer
definition, while Huawei Nexus 6P gains eMMC support.
On MSM8996 the modem and sensor remtoeprocs are added and enabled in the
Dragonboard 820c and the Xiaomi devices.
On MSM8998 a few newly added clocks related to the sensor subsystem bus
are marked as protected by default and the OnePlus devices gains NFC.
The SC7180 platform and devices thereon are further polished and
limozeen moves to using edp-panel for EDID-based detection, over
statically defined panels.
On SC7280 GPI DMA, WiFi remoteproc and network device, LPASS audio
clocks, resets for SDCC controllers and a new CRD revision are added. A
supply glitch on the PCIe power and a current leak for Bluetooth during
suspend are corrected. The Herobrine board gains eDP support and the IDP
gains backlight. USB is marked wakeup capable.
On SDM845 the IPA, WLED based backlight and second WiFi channel are
enabled for Xiaomi Pocophone F1, the firmware name is modified to not
conflict with other boards. On RB3 the CAN bus controller is added and
the WiFi calibration variant is defined to allow adding the board's
calibration information into linux-firmware.
SM6350 gains I2C busses, UFS and WiFi support, and the numbering of
uart9 is corrected.
On SM7225 and the Fairphone 4 UFS, WiFi and haptics are enabled.
On SM8150 PCIe, Ethernet and uSD card support is added, and enabled for
the SA8155p ADP board. The PDC interrupt controller is also added and
described as wakup interrupt parent for TLMM.
Camera subsystem and control interface are defined for SM8250. On the
Sony Xperia 1 II the audio amplifiers are enabled.
On SM8350 GPI DMA engines are added and linked to the I2C and SPI
serial engines. Surface Duo 2 gains battery charger support.
On SM8450 the two PCIe controller/PHYs are enabled, GPI DMA and QUP
serial engine instances are added. Remoteproc instances are enabled on
SM8450 HDK.
Last, but not least, a number of DeviceTree validation errors across
various boards are corrected.
* tag 'qcom-arm64-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (150 commits)
arm64: dts: qcom: Only include sc7180.dtsi in sc7180-trogdor.dtsi
arm64: dts: qcom: sc7180-trogdor: Simplify spi0/spi6 labeling
arm64: dts: qcom: sc7180-trogdor: Simplify trackpad enabling
arm64: dts: qcom: sc7280: eDP for herobrine boards
arm64: dts: qcom: sa8155p-adp: Disable multiple Tx and Rx queues for ethernet IP
arm64: dts: qcom: sm8150: Fix iommu sid value for SDC2 controller
arm64: dts: qcom: sm8350-duo2: enable battery charger
arm64: dts: qcom: Enable pm8350c pwm for sc7280-idp2
arm64: dts: qcom: pm8350c: Add pwm support
arm64: dts: qcom: sc7280-qcard: Configure CTS pin to bias-bus-hold for bluetooth
arm64: dts: qcom: sc7280-idp: Configure CTS pin to bias-bus-hold for bluetooth
arm64: dts: qcom: sc7180: Remove ipa interconnect node
arm64: dts: qcom: sc7280-idp: Enable GPI DMAs
arm64: dts: qcom: sc7280: Add GENI I2C/SPI DMA channels
arm64: dts: qcom: sc7280: Add GPI DMAengines
arm64: dts: qcom: sm8450: Fix qmp phy node (use phy@ instead of lanes@)
arm64: dts: qcom: db845c: Add support for MCP2517FD
arm64: dts: qcom: qrb5165-rb5: Fix can-clock node name
arm64: dts: qcom: sc7280: Add SAR sensors to herobrine crd
arm64: dts: qcom: sm8250: camss: Add CCI definitions
...
Link: https://lore.kernel.org/r/20220509204451.325675-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: tegra: Device tree changes for v5.19-rc1
This adds some improvements on Tegra234 (QSPI, CCPLEX), improves the
SDMMC clock speed on Tegra194 and adds the ASRC audio block on various
chip generations. Memory controller channels are also added on Tegra186
and later and the missing DFLL reset is added for Tegra210.
* tag 'tegra-for-5.19-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add missing DFLL reset on Tegra210
arm64: tegra: Add memory controller channels
arm64: tegra: Enable ASRC on various platforms
arm64: tegra: Add ASRC device on Tegra186 and later
arm64: tegra: Update PWM fan node name
arm64: tegra: Add node for Tegra234 CCPLEX cluster
arm64: tegra: Add QSPI controllers on Tegra234
arm64: tegra: Update SDMMC1/3 clock source for Tegra194
Link: https://lore.kernel.org/r/20220506143005.3916655-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Renesas ARM DT updates for v5.19 (take two)
- I2C, sound, USB, CANFD, timer, watchdog, (Q)SPI, cpufreq, and
thermal support for the RZ/G2UL SoC and the RZ/G2UL SMARC EVK
development board,
- Initial support for the R-Car V4H SoC and the Renesas White Hawk
development board stack,
- DMA, RTC, and USB support for the RZ/N1D SoC,
- Initial support for the RZ/V2M SoC an the RZ/V2M Evaluation Kit
Board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (40 commits)
arm64: dts: renesas: Add initial device tree for RZ/V2M EVK
arm64: dts: renesas: Add initial DTSI for RZ/V2M SoC
arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
ARM: dts: r9a06g032: Link the PCI USB devices to the USB PHY
ARM: dts: r9a06g032: Add USB PHY DT support
ARM: dts: r9a06g032: Add internal PCI bridge node
ARM: dts: r9a06g032: Describe the RTC
arm64: dts: renesas: Add interrupt-names to CANFD nodes
arm64: dts: renesas: r9a07g043: Add SPI Multi I/O Bus controller node
arm64: dts: renesas: r9a07g043: Create thermal zone to support IPA
arm64: dts: renesas: r9a07g043: Add TSU node
arm64: dts: renesas: r9a07g043: Add OPP table
arm64: dts: renesas: r9a07g043: Add RSPI{0,1,2} nodes
arm64: dts: renesas: r9a07g054: Fix external clk node names
arm64: dts: renesas: r9a07g044: Fix external clk node names
ARM: dts: r9a06g032: Fix the NAND controller node
ARM: dts: r9a06g032: Fill the UART DMA properties
ARM: dts: r9a06g032: Describe the DMA router
ARM: dts: r9a06g032: Add the two DMA nodes
arm64: dts: renesas: Remove empty rgb output endpoints
...
Link: https://lore.kernel.org/r/cover.1651828603.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The RTC section of the H616 manual mentions in a half-sentence the
existence of a clock "32K divided by PLL_PERI(2X)". This is used as
one of the possible inputs for the mux that selects the clock for the
32 KHz fanout pad. On the H616 this is routed to pin PG10, and some
boards use that clock output to compensate for a missing 32KHz crystal.
On the OrangePi Zero2 this is for instance connected to the LPO pin of
the WiFi/BT chip.
The new RTC clock binding requires this clock to be named as one input
clock, so we need to expose this to the DT. In contrast to the D1 SoC
there does not seem to be a gate for this clock, so just use a fixed
divider clock, using a newly assigned clock number.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220428230933.15262-3-andre.przywara@arm.com
The H6 and H616 feature an (undocumented) bus clock gate for accessing
the RTC registers. This seems to be enabled at reset (or by the BootROM),
so we got away without it so far, but exists regardless.
Since the new RTC clock binding for the H616 requires this "bus" clock
to be specified in the DT, add this to R_CCU clock driver and expose it
on the DT side with a new number.
We do this for both the H6 and H616, but mark it as IGNORE_UNUSED, as we
cannot reference it in any H6 DTs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220428230933.15262-2-andre.przywara@arm.com
STM32 DT for v5.19, round 1
Highlights:
----------
-MCU:
-Fix pinctrl node names to match with pinctrl yaml.
- MPU:
-General:
- Fix pinctrl node names to match with pinctrl yaml.
- Add Protonics boards support based on STM32MP151A SoC:
- PRTT1C - 10BaseT1L switch: mainly embeds a sja1105q switch with
TI and Micrel 10BaseT Phys and wifi support.
- PRTT1S - 10BaseT1L CO2 sensor board: mainly embeds I2C humidity
and CO2 sensors.
- PRTT1A - 10BaseT1L multi functional controller.
- ST boards:
- Add RTC support on stm32mp13.
- Add button and heartbit support on stm32mp13 DK board.
- Add a secure version of STM32MP15 ED1/EV1/DK1/DK2 boards based
on OP-TEE OS and SCMI protocol.
- DH boards:
- Use MCO2 to generate PHY clock and ETHRX clock in order to release
internal PLL for a better SD card usage.
- Add 1ms PHY post-reset on Avenger96 board to match with PHY
requirements.
* tag 'stm32-dt-for-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (24 commits)
ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
dt-bindings: arm: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15
dt-bindings: reset: stm32mp15: rename RST_SCMI define
dt-bindings: clock: stm32mp15: rename CK_SCMI define
dt-bindings: clock: stm32mp1: describes clocks if "st,stm32mp1-rcc-secure"
dt-bindings: rcc: Add optional external ethernet RX clock properties
ARM: dts: stm32: add UserPA13 button on stm32mp135f-dk
ARM: dts: stm32: add blue led (Linux heartbeat) on stm32mp135f-dk
ARM: dts: stm32: add EXTI interrupt-parent to pinctrl node on stm32mp131
ARM: dts: stm32: add support for Protonic PRTT1x boards
ARM: dts: stm32: stm32mp15-pinctrl: add spi1-1 pinmux group
dt-bindings: net: silabs,wfx: add prt,prtt1c-wfm200 antenna variant
dt-bindings: arm: stm32: Add compatible strings for Protonic T1L boards
dt-bindings: arm: stm32: correct blank lines
dt-bindings: arm: stm32: narrow DH STM32MP1 SoM boards
ARM: dts: stm32: enable RTC support on stm32mp135f-dk
ARM: dts: stm32: add RTC node on stm32mp131
ARM: dts: stm32: Fix PHY post-reset delay on Avenger96
ARM: dts: stm32: fix pinctrl node name warnings (MPU soc)
...
Link: https://lore.kernel.org/r/5818c943-882d-7e50-430d-ae3299a108ee@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
