Raw NAND core changes:
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_match_ptr() either expands to NULL if !CONFIG_OF, or is transparent
otherwise. There are several drivers using this macro which keep their
of_device_id array enclosed within an #ifdef CONFIG_OF check, these are
considered fine. However, When misused, the of_device_id array pointed
by this macro will produce a warning because it is finally unused when
compiled without OF support.
A number of fixes are possible:
- Always depend on CONFIG_OF, but this will not always work and may
break boards.
- Enclose the compatible array by #ifdef's, this may save a bit of
memory but will reduce build coverage.
- Tell the compiler the array may be unused, if this can be avoided,
let's not do this.
- Just drop the macro, setting the of_device_id array for a non OF
enabled platform is not an issue, it will just be unused.
The latter solution seems the more appropriate, so let's use it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/linux-mtd/20220127110631.1064705-1-miquel.raynal@bootlin.com
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
The name/suffix data_interface is a bit misleading in that the field
or functions actually represent a configuration that can be applied by
the controller/chip. Let's rename all fields/functions/hooks that are
worth renaming.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NAND controller drivers can set the NAND_USE_BOUNCE_BUFFER flag to a
chip 'option' field. With this flag, the core is responsible of
providing DMA-able buffers.
The current behavior is to not force the use of a bounce buffer when
the core thinks this is not needed. So in the end the name is a bit
misleading, because in theory we will always have a DMA buffer but in
practice it will not always be a bounce buffer.
Rename this flag NAND_USES_DMA to be more accurate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-4-miquel.raynal@bootlin.com
devm_fwnode_get_index_gpiod_from_child() is going away as the name is
too unwieldy, let's switch to using the new devm_fwnode_gpiod_get().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Wrong copy/paste from the previous block, the error message should
refer to #size-cells instead of #address-cells.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
nand_device embeds a nand_ecc_req object which contains the minimum
strength and step-size required by the NAND device.
Drop the chip->ecc_{strength,step}_ds fields and use
chip->base.eccreq.{strength,step_size} instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The sam9x60 board defines the CCFG_EBICSA register under SFR,
and not as a MATRIX register, as previous boards do.
NAND Flash I/Os are connected to D16–D23, thus
SFR_CCFG_EBICSA.NFD0_ON_D16 is set to 1.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The sam9x60 board defines the CCFG_EBICSA register under SFR,
and not as a MATRIX register, as previous boards do. Add a
more generic name for the EBICSA regmap, as a prerequisite for
sam9x60 nand controller support.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
->setup_data_interface() is a controller specific method and should
thus be placed in nand_controller_ops.
In order to make that work with controllers that support keeping
pre-configured timings we need to add a new NAND_KEEP_TIMINGS flag to
inform the core it should skip the timings selection step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS line to be selected is passed to ->exec_op() and
stored in chip->cur_cs and after patching all drivers implementing
->exec_op() to stop implementing this method, we can deprecate it by
moving it to the nand_legacy structure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the new of_get_compatible_child() helper to lookup the nfc child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
While at it, also fix a related nfc-node reference leak.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: stable <stable@vger.kernel.org> # 4.11
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Josh Wu <rainyfeeling@outlook.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
There is a potential execution path in which function
of_find_compatible_node() returns NULL. In such a case,
we end up having a NULL pointer dereference when accessing
pointer *nfc_np* in function of_clk_get().
So, we better don't take any chances and fix this by null
checking pointer *nfc_np* before calling of_clk_get().
Addresses-Coverity-ID: 1473052 ("Dereference null return value")
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The wait timeouts and delays are directly extracted from the NAND
timings and ->chip_delay is only used in legacy path, so let's move it
to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->setup_data_interface() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->waitfunc() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->dev_ready() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmd_ctrl() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->select_chip() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to take
a nand_chip object instead of an mtd_info one.
We start with nand_scan().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
