The 128b/132b channel coding link training uses more straightforward TX
FFE preset values. Reuse voltage tries and max vswing for retry logic.
The delays for 128b/132b are still all wrong, but this is regardless a
step forward.
v2: Fix UHBR rate checks, use intel_dp_is_uhbr() helper
v3:
- Rebase
- Modify intel_dp_adjust_request_changed() and
intel_dp_link_max_vswing_reached() to take 128b/132b into
account. (Ville)
v4:
- Train request printing for TX FFE (Ville)
- Log 8b/10b vs. 128b/132b (Ville)
- Add helper for per-lane max vswing / tx ffe (Ville)
- Name functions with tx_ffe/vswing instead of 128b132b/8b10b
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211011182144.22074-2-jani.nikula@intel.com
Currently .set_signal_levels() is only used by encoders in DP mode.
For most modern platforms there is no essential difference between
DP and HDMI, and both codepaths just end up calling the same function
under the hood. Let's get remove the need for that extra indirection
by moving .set_signal_levels() into the encoder from intel_dp.
Since we already plumb the crtc_state/etc. into .set_signal_levels()
the code will do the right thing for both DP and HDMI.
HSW/BDW/SKL are the only platforms that need a bit of care on
account of having to preload the hardware buf_trans register
with the full set of values. So we must still remember to call
hsw_prepare_{dp,hdmi}_ddi_buffers() to do said preloading, and
.set_signal_levels() will just end up selecting the correct entry
for DP, and also setting up the iboost magic for both DP and HDMI.
Note that previously on HSW/BDW/SKL we did write to DDI_BUF_CTL to
select the correct entry until link training started, now that we
call .set_signal_levels() already from hsw_ddi_pre_enable_dp() that
is no longer the case. But it's all safe now that the
intel_ddi_init_dp_buf_reg() call was hoisted up and it no longer
sets up the DDI_BUF_CTL_ENABLE bit (that is still deferred until
link training).
v2: Rebase due to has_{iboost,buf_trans_select}()
Add some notes about the DDI_BUF_CTL situation on HSW/BDW/SKL (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-4-ville.syrjala@linux.intel.com
I want intel_dp->DP to be fully populated by the time the
initial vswing programming happens. To that end move the
intel_ddi_init_dp_buf_reg() call to an earlier spot.
Additionally we don't want intel_ddi_init_dp_buf_reg() to
set DDI_BUF_CTL_ENABLE since the port should only get enabled
at the start of link training (see intel_ddi_prepare_link_retrain()).
So any earlier write to the register should not set the enable bit.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
So far TC-cold was blocked only for the duration of TypeC mode resets.
The DP-alt and legacy modes require TC-cold to be blocked also whenever
the port is in use (AUX transfers, enable modeset), and this was ensured
by the held PHY ownership flag. On ADL-P this doesn't work, since the
PHY ownership flag is in a register backed by the PW#2 power well.
Whenever this power well is disabled the ownership flag is cleared by
the HW under the driver.
The only way to cleanly release and re-acquire the PHY ownership flag
and also allow for power saving (by disabling the display power wells
and reaching DC5/6 states) is to hold the TC-cold blocking power domains
while the PHY is connected and disconnect/reconnect the PHY on-demand
around AUX transfers and modeset enable/disables. Let's do that,
disconnecting a PHY with a 1 sec delay after it becomes idle. For
consistency do this on all platforms and TypeC modes.
v2: Add tc_mode!=disconnected and phy_is_owned asserts to
__intel_tc_port_lock().
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-6-imre.deak@intel.com
PSR always had a requirement to only be enabled if there is active
planes but not following that never caused any issues.
But that changes in Alderlake-P, leaving PSR enabled without
active planes causes transcoder/port underruns.
Similar behavior was fixed during the pipe disable sequence by
commit 84030adb9e ("drm/i915/display: Disable audio, DRRS and PSR before planes").
intel_dp_compute_psr_vsc_sdp() had to move from
intel_psr_enable_locked() to intel_psr_compute_config() because we
need to be able to disable/enable PSR from atomic states without
connector and encoder state.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922215242.66683-3-jose.souza@intel.com
PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder.
Bigjoiner is making life even more confusing by introducing
a N:1 relationship between pipes and transcoders. In that case
we only enable/configure the transcoder corresponding to the
master pipe. Let's do some renames to make it clear we're dealing
with the transcoder rather than pipe when it comes to
PIPECONF/TRANSCONF.
I decided to leave the _cpu_ part out from the function/macro
names since the PCH transcoder related stuff already has a
_pch_ in their name. So shouldn't be possible to confuse them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
DG1 and XE_PLD platforms has Audio MMIO/VERBS lies in PG0 power
well. Adjusting the power domain accordingly to
POWER_DOMAIN_AUDIO_MMIO for audio detection and
POWER_DOMAIN_AUDIO_PLAYBACK for audio playback.
While doing this it requires to use POWER_DOMAIN_AUDIO_MMIO
power domain instead of POWER_DOMAIN_AUDIO in crtc power domain mask
and POWER_DOMAIN_AUDIO_PLAYBACK with intel_display_power_{get, put}
to enable/disable display audio codec power.
It will save the power in use cases when DP/HDMI connectors
configured with PIPE_A without any audio playback.
v1: Changes since RFC
- changed power domain names. [Imre]
- Removed TC{3,6}, AUX_USBC{3,6} and TBT from DG1
power well and PW_3 power domains. [Imre]
- Fixed the order of powe wells , power domains and its
registration. [Imre]
v2:
- Not allowe DC states when AUDIO_MMIO domain enabled. [Imre]
v3:
- Squashes the commits of series to avoid build failure.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
[Fix typo in commit message and in AUDIO_PLAYBACK domain name]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210729121858.16897-2-anshuman.gupta@intel.com
HDMI and DisplayPort sequences states that audio and PSR should be
disabled before planes are disabled.
Not following it did not caused any problems up to Alderlake-P but
for this platform it causes underruns during the PSR2 disable
sequence.
Specification don't mention that DRRS should be disabled before planes
but it looks safer to switch back to the default refresh rate before
following with the rest of the pipe disable sequence.
BSpec: 49191
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210726181559.80855-1-jose.souza@intel.com
_DG1_DPCLKA0_CFGCR0 maps between DPLL 0 and 1 with one bit for phy A
and B while _DG1_DPCLKA1_CFGCR0 maps between DPLL 2 and 3 with one
bit for phy C and D.
Reusing _cnl_ddi_get_pll() don't take that into cosideration returing
DPLL 0 and 1 for phy C and D.
That is a regression introduced in the refactor done in
commit 351221ffc5 ("drm/i915: Move DDI clock readout to
encoder->get_config()").
While at it also dropping the macros previously used, not reusing it
to improve readability.
BSpec: 50286
Fixes: 351221ffc5 ("drm/i915: Move DDI clock readout to encoder->get_config()")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210630210522.162674-1-jose.souza@intel.com
Disconnect TypeC PHYs during system suspend and shutdown, even with the
corresponding TypeC sink still plugged to its connector, since leaving
the PHY connected causes havoc at least during system resume in the
presence of an Nvidia card.
Note that this will only make a difference in the TypeC DP alternate
mode, since in Thunderbolt alternate mode the PHY is never owned by the
display engine and there is no notion of PHY ownership in legacy mode
(the display engine being the only possible owner in that mode and the
TypeC subsystem not having anything to do with the port in that case).
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3500
Reported-and-tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610174223.605904-1-imre.deak@intel.com
