V1:
1. The MCU FW controling ASPEED DP is loaded by BMC boot loader.
2. Driver starts after CR[3:1] == 111b that indicates Tx is ASTDP,
and CRD1[5] has been asserted by BMVC boot loader.
3. EDID is prioritized by DP monitor.
4. DP's EDID has high priority to decide resolution supporting.
V2:
Modules description:
1. ASTDP (ASPEED DisplayPort) is controlled by dedicated
AST-MCU (ASPEED propriatary MCU).
2. MCU is looping in charged of HPD, Read EDID, Link Training with
DP sink.
3. ASTDP and AST-MUC reside in BMC (Baseboard Management controller)
addressing-space.
4. ASPEED DRM driver requests MCU to get HPD and EDID by CR-scratched
register.
Booting sequence:
1. Check if TX is ASTDP // ast_dp_launch()
2. Check if DP-MCU FW has loaded // ast_dp_launch()
3. Read EDID // ast_dp_read_edid()
4. Resolution switch // ast_dp_SetOutput()
V3:
1. Remove unneeded semicolon.
2. Apply to git://anongit.freedesktop.org/drm/drm, instead of
git://anongit.freedesktop.org/drm/drm-misc
3. Resolve auto build test WARNINGs on V1 patch.
V4:
1. Sync code-base with kernel 5.17_rc6
2. Remove the define of DPControlPower, because DP chips need to be
powered on to be used.
3. Remove the switches of PHY and Display from EDID procedure.
4. Revise increaing delay to fixed delay, because this version kernel
doesn't detect minitor consistenntly.
5. Create clean-up code used for reset of power state on errors with
-EIO manner.
6. Revise the DP detection by TX type and its DP-FW status during
booting and resume.
7. Correct the CamelCase Style.
8. Use register reading while needing, and remove to hold full
register.
9. Instead of 'u8', revise to 'bool' on swwitch of PHY and video.
10.Correct typo
11.Remove the duplicated copy of TX definition.
12.Use EDID_LENGTH as the constant of 128.
Signed-off-by: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428075603.20904-1-kuohsiang_chou@aspeedtech.com
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/686ec871-e77f-c230-22e5-9e3bb80f064a@linux.intel.com
Add helpers for initializing SIL164-based connectors. These used to be
handled by the VGA connector code. But SIL164 provides output via DVI-I,
so set the encoder and connector types accordingly.
If a SIL164 chip has been detected, ast will now create a DVI-I
connector instead of a VGA connector.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220207141544.30015-10-tzimmermann@suse.de
Add helpers for DP501-based connectors. DP501 provides output via
DisplayPort. This used to be handled by the VGA connector code.
If a DP501 chip has been detected, ast will now create a DisplayPort
connector instead of a VGA connector.
Remove the DP501 code from ast_vga_connector_helper_get_modes(). Also
remove the call to drm_connector_update_edid_property(), which is
performed by drm_get_edid().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220207141544.30015-9-tzimmermann@suse.de
Rename struct dma_buf_map to struct iosys_map and corresponding APIs.
Over time dma-buf-map grew up to more functionality than the one used by
dma-buf: in fact it's just a shim layer to abstract system memory, that
can be accessed via regular load and store, from IO memory that needs to
be acessed via arch helpers.
The idea is to extend this API so it can fulfill other needs, internal
to a single driver. Example: in the i915 driver it's desired to share
the implementation for integrated graphics, which uses mostly system
memory, with discrete graphics, which may need to access IO memory.
The conversion was mostly done with the following semantic patch:
@r1@
@@
- struct dma_buf_map
+ struct iosys_map
@r2@
@@
(
- DMA_BUF_MAP_INIT_VADDR
+ IOSYS_MAP_INIT_VADDR
|
- dma_buf_map_set_vaddr
+ iosys_map_set_vaddr
|
- dma_buf_map_set_vaddr_iomem
+ iosys_map_set_vaddr_iomem
|
- dma_buf_map_is_equal
+ iosys_map_is_equal
|
- dma_buf_map_is_null
+ iosys_map_is_null
|
- dma_buf_map_is_set
+ iosys_map_is_set
|
- dma_buf_map_clear
+ iosys_map_clear
|
- dma_buf_map_memcpy_to
+ iosys_map_memcpy_to
|
- dma_buf_map_incr
+ iosys_map_incr
)
@@
@@
- #include <linux/dma-buf-map.h>
+ #include <linux/iosys-map.h>
Then some files had their includes adjusted and some comments were
update to remove mentions to dma-buf-map.
Since this is not specific to dma-buf anymore, move the documentation to
the "Bus-Independent Device Accesses" section.
v2:
- Squash patches
v3:
- Fix wrong removal of dma-buf.h from MAINTAINERS
- Move documentation from dma-buf.rst to device-io.rst
v4:
- Change documentation title and level
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204170541.829227-1-lucas.demarchi@intel.com
[Bug][AST2500]
V1:
When AST2500 acts as stand-alone VGA so that DRAM and DVO initialization
have to be achieved by VGA driver with P2A (PCI to AHB) enabling.
However, HW suggests disable Fast reset mode after DRAM initializaton,
because fast reset mode is mainly designed for ARM ICE debugger.
Once Fast reset is checked as enabling, WDT (Watch Dog Timer) should be
first enabled to avoid system deadlock before disable fast reset mode.
V2:
Use to_pci_dev() to get revision of PCI configuration.
V3:
If SCU00 is not unlocked, just enter its password again.
It is unnecessary to clear AHB lock condition and restore WDT default
setting again, before Fast-reset clearing.
V4:
repatch after "error : could not build fake ancestor" resolved.
V5:
Since CVE_2019_6260 item3, Most of AST2500 have disabled P2A(PCIe to AMBA).
However, for backward compatibility, some patches about P2A, such as items
of v5.2 and v5.3, are considered to be upstreamed with comments.
1. Add define macro to improve source readability.
ast_drv.h, ast_main.c, ast_post.c
2. Add comment about "Fast restet" is enabled for ARM-ICE debugger
ast_post.c
3. Add comment about Reset USB port to patch USB unknown device issue
ast_post.c
Signed-off-by: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210709080900.4056-1-kuohsiang_chou@aspeedtech.com
[Bug][DP501]
If ASPEED P2A (PCI to AHB) bridge is disabled and disallowed for
CVE_2019_6260 item3, and then the monitor's EDID is unable read through
Parade DP501.
The reason is the DP501's FW is mapped to BMC addressing space rather
than Host addressing space.
The resolution is that using "pci_iomap_range()" maps to DP501's FW that
stored on the end of FB (Frame Buffer).
In this case, FrameBuffer reserves the last 2MB used for the image of
DP501.
Signed-off-by: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210421085859.17761-1-kuohsiang_chou@aspeedtech.com
The BOs of the hardware cursor are now mapped permanently while the
cursor plane is being used. This reduces the CPU overhead of the cursor
plane's atomic_update function.
The change also resolves a problem with the vmap call in the commit tail.
The vmap implementation could acquire the DMA reservation lock on the
BO, which is not allowed that late in the atomic update. Removing the
vmap call from atomic_update fixes the issue.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209134632.12157-9-tzimmermann@suse.de
The HW cursor's BO used to be mapped permanently into the kernel's
address space. GEM's vmap operation will be protected by locks, and
we don't want to lock the BO's for an indefinate period of time.
Change the cursor code to map the HW BOs only during updates. The
vmap operation in VRAM helpers is cheap, as a once estabished mapping
is being reused until the BO actually moves. As the HW cursor BOs are
permanently pinned, they never move at all.
v2:
* fix typos in commit description
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209142527.26415-3-tzimmermann@suse.de
This patch replaces the vmap/vunmap's use of raw pointers in GEM object
functions with instances of struct dma_buf_map. GEM backends are
converted as well. For most of them, this simply changes the returned type.
TTM-based drivers now return information about the location of the memory,
either system or I/O memory. GEM VRAM helpers and qxl now use ttm_bo_vmap()
et al. Amdgpu, nouveau and radeon use drm_gem_ttm_vmap() et al instead of
implementing their own vmap callbacks.
v7:
* init QXL cursor to mapped BO buffer (kernel test robot)
v5:
* update vkms after switch to shmem
v4:
* use ttm_bo_vmap(), drm_gem_ttm_vmap(), et al. (Daniel, Christian)
* fix a trailing { in drm_gem_vmap()
* remove several empty functions instead of converting them (Daniel)
* comment uses of raw pointers with a TODO (Daniel)
* TODO list: convert more helpers to use struct dma_buf_map
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Tested-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201103093015.1063-7-tzimmermann@suse.de
The ast HW cursor requires the primary plane and CRTC to display at
a valid mode and format. This is not the case while switching
display modes, which can lead to the screen turing permanently dark.
As a workaround, the ast driver now disables active planes while the
mode or format switch takes place. It also synchronizes with the vertical
refresh to give CRTC and planes some time to catch up on each other.
The active planes planes (primary or cursor) will be re-enabled by
each plane's atomic_update() function.
v3:
* move the logic into the CRTC's atomic_disable function
v2:
* move the logic into the commit-tail function
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200914072236.19398-3-tzimmermann@suse.de
The ast driver's load and unload functions are left-overs from when
struct drm_driver.load/unload was still in use. The PCI probe helper
allocated the DRM device and ran load to initialize it.
This patch replaces this code with device create and destroy. The
main difference is that the device's create function allocates the
DRM device and ast structures in the same place. This will be required
for switching ast to managed allocations.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200730135206.30239-4-tzimmermann@suse.de
Updating the image in a cursor's HW BO requires a mapping of the BO's
buffer in the kernel's address space. Cursor image updates can happen
frequently and create CPU overhead.
As cursor HW BOs are small and never move, they are now map exactly
once during the initialization and the mapping is used throughout the
driver's lifetime.
This change also removes a possible source of failures from
ast_cursor_show(). As the helper does not establish mappings, it cannot
fail. As a result, the cursor plane's atomic-update helper does not
call any failable interfaces. All failures are detected before trying
to update the cursor plane.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702115029.5281-10-tzimmermann@suse.de
Having a cursor move function is misleading, as it actually enables the
cursor's image for displaying. So rename it to ast_cursor_show(). It's
semantics is to show a cursor at the specified location on the screen.
The displayed cursor is always the image in the cursor front BO.
This change also simplifies struct ast_crtc to being a mere wrapper around
around struct drm_crtc. It will be removed by a later patch.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702115029.5281-7-tzimmermann@suse.de
The new helper ast_cursor_blit() updates a cursor's backbuffer HW
BO from a framebuffer structure. The cursor plane's prepare_fb()
function now uses the new interface.
Pinning and mapping of BOs is done automatically by the helper. This
includes the source BO, which was not pinned by the original code in
prepare_fb().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702115029.5281-4-tzimmermann@suse.de
Reading the primary plane's framebuffer from the CRTC's atomic_flush()
function is fragile as the plane state or framebuffer can be NULL.
Instead, we let the plane's atomic_check() store the framebuffer format
in the CRTC state. The CRTC always receives the framebuffer format that
is currently programmed, or NULL if no mode has been set yet.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191202111557.15176-8-tzimmermann@suse.de
