[why]
Feature requires synchronization of dig, pipe, and cursor locking
between driver and DMUB fw for PSR-SU
[how]
return True if PSR-SU in the checker should_use_dmub_lock()
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
While support ALPM, do ALPM state transition while PSR entry/exit.
ALPM is needed for PSR-SU feature, and since the function is ready,
we'd enable it by default.
- Add psr level definition to enable/disable ALPM and set ALPM
powerdone mode.
- Enable ALPM by default
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When DC driver send PSR exit dmub command to DMUB FW, it might not
wait until PSR exit. Then it may hit the following deadlock situation.
1. DC driver send HW LOCK command to DMUB FW due to frame update
2. DMUB FW Set the HW lock
3. DMUB execute PSR exit sequence and stuck at polling DPG Pending
register due to the HW Lock is set
4. DC driver ask DMUB FW to unlock HW lock, but DMUB FW is polling
DPG pending register
[how]
The reason why DC driver doesn't wait until PSR exit is because some of
the PSR state machine state is not update the dc driver. So when DC
driver read back the PSR state, it take the state for PSR inactive.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current PSR SU programming margin is fixed base on FHD 60HZ
panel. If the resolution and refresh rate become higher, the time
of current margin might not cover the programming SU time.
[how]
Notice that the programming SU time is the same among different
panels.
Instead of fixing the margin with target line number, change the
margin unit to micro second which indicate the time needed for
programming SU. Then FW set the margin line number base on the
line time and margin time.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The Y-granularity panel parameter indicate the grid
pattern granularity in the Y direction for PSRSU.
[How]
Send the Y-granularity data by PSR_COPY_SETTINGS dmub command.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Based on PSRSU specification, every selective update frame need to use
two SDP to indicate the frame active range. So we occupy another GSP1
for PSRSU execution.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In PSR-SU design, the DMUB FW handles the combination of multiple
dirty rectangles.
[how]
- create DC dmub update dirty rectangle helper which sends the
dirty rectangles per pipe from DC to DMUB, and DMUB FW will
handle to combine the dirty RECTs
- call the helper from DC commit plane update function.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
PSR-SU is implemented in upstreamed dmub FW but not enabled on
DM and DC. We'd add necessary and missing definitions in dmub
cmd header to align w/ the up-to-date DMUB FW for PSR-SU support.
[how]
Add definitions and items below into dmub cmd header:
- DMUB psr version enumeration for PSR-SU
- dirty rectangle structure
- psr debug flag of forcing full frame update
- dmub command of updating dirty rectangle and cursor infor
- dmub psr command type of setting sink vtotal in PSR active
- dmub psr su debug flags structure
- dmub cmd structure for
- updating dirty rectangle
- cursor infor
- setting sink vtotal
- dmub ringbuffer command items
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Protect remove_hpo_dp_link_enc_from_ctx() and release_hpo_dp_link_enc()
with CONFIG_DRM_AMD_DC_DCN as the functions are only called from code
that is protected by CONFIG_DRM_AMD_DC_DCN. Fixes build fail with
-Werror=unused-function.
Fixes: 9b0e0d433f74 ("drm/amd/display: Add dependant changes for DCN32/321")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Revised validation logic when marking for seamless boot. Init resources
accordingly when Pre-OS has ODM enabled. Reset ODM when transitioning
Pre-OS odm to Post-OS non-odm to avoid corruption. Apply logic to set
odm accordingly upon commit.
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Implements DTB ref clock switching with reg key default to OFF.
Refactors dccg DTBCLK logic to not store redundant state information
dccg. Also removes duplicated functions that should be inherited from
other dcn versions.
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update base.dprefclk_khz to match result from dcn32_dump_clk_registers()
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit cleans up code that uses old variables and adds some SMU
interfaces for future flexibility.
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously we used to send FCLK P-state enable messages upon each call
to update_clocks based on dml output. This resulted in increased message
transactions between DC and PMFW.
[How]
Update the code to check safe_to_lower status and send the message based
on dml input only on boot. This reduces message transactions. Also
remove other unwanted code based on current code status.
Signed-off-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DCN has sidebands to control some clocks, it is useful for clk_mgr to
always update the clocks it explicitly controls rather than skip them
because it enables more configurations to work without SMU
[how]
only skip handling clocks where SMU manages the frequency for clocks
with DENTIST sideband (DISP/DPP), only skip the voltage request when SMU
not available, but otherwise proceed normally
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
New dividers in DCCG need to be programmed depending
on encoder/stream type since pixels per clock in
OTG/DIO is different
DIO also needs additional programming depending on
pixels per clock
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
[Why]
HUBP_UNBOUNDED_REQ_MODE and CURSOR_REQ_MODE are normally set together.
In hubp32_prepare_subvp_buffering() call, CURSOR_REQ_MODE is set based on
whether SubVP is enabled or not. For non MPO case, both REQ_MODE
registers are set to 1. But since SubVP is not enabled, then
CURSOR_REQ_MODE is set to 0, overriding the previous value.
[How]
Do not set CURSOR_REQ_MODE to 0 if SubVP is not enabled. This
will allow CURSOR_REQ_MODE to stay as 1 in the non MPO case.
Add note to follow up and check case for single pipe MPO and
SubVP enabled as this would cause both REQ_MODE registers to be
set to 0 but SubVP enabled would override CURSOR_REQ_MODE to 1.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
If higher states have memory speed set to 0 MT/s currently they do not get set
to the highest value which can cause validation failures.
[HOW?]
Set unpopulated higher states to max value.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VBIOS default clock value was halved, so the hardcoded dtb value should be
halved as well.
dtb clock should come from SMU eventually, but now dtb clock switching is not
fully supported yet in SMU.
Halve the dtb hardcoded value for now to have UHBR10 light up. Will rely on
SMU for dtb clock switching once available. The w/a is for DCN32 only, DCN321
should adopt the original value.
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why?]
On wake from S3/S4, driver checks if DMUB is initialized. On S4 VBIOS loads
DMUB, and driver does not reload as it appears to be initialized already.
[How?]
Add a check for the DAL_FW bit to ensure that loaded FW is from driver and
not VBIOS.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Need to add inst 5 for clk_src_regs because
there are 5 PHY instances in DCN32 & DCN321.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Add USBC connector ID to align with new VBIOS parsing.
Add seperate DCN321 link encoder due to different PHY version affecting
DP ALT related registers.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX11 IP introduces new tiling mode. Various combinations of DCC
settings are possible and the most preferred settings must be exposed
for optimal use of the hardware.
add_gfx11_modifiers() is based on recommendation from Marek for the
preferred tiling modifier that are most efficient for the hardware.
v2: microtiling fix noticed by Marek
v3: keep Z tiling check
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add Display Manager specific changes for DCN3.2.x. DM
handles the interaction between the core DC modesetting
code and the drm modesetting infrastructure.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
