Remove the variable clk_src from the function dcn3_get_pix_clk_dividers.
This was pointed by clang with the following warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:1279:25: warning:
variable 'clk_src' set but not used [-Wunused-but-set-variable]
struct dce110_clk_src *clk_src;
^
1 warning generated.
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the case where we don't support DMUB aux but we have DPIA links
in the configuration we might try to message AUX using the legacy
path - where DDC pin is NULL. This causes a NULL pointer dereference.
[How]
Guard against NULL DDC pin, return a failure for aux engine acquire.
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR-SU Rate Control - or PSR-SU-RC - enables PSR-SU panels to work with
variable refresh rate to allow for more power savings. Lowering the
refresh rate can increase PSR residency by expanding the eDP main link
shut down duration. It can also lower panel power consumption.
There is a complication with PSR, since the eDP main link can be shut
down. Therefore, the timing controller (TCON) on the eDP sink nees to be
able to scan out its remote buffer independent of the main link. To
allow the eDP source to specify the sink's refresh rate while the link
is off, vendor-specific DPCD registers are used. This allows the eDP
source to then "Rate Control" the panel during PSR active.
[How]
Add DC support to communicate with PSR-SU-RC supported eDP sinks. The
sink will need to know the desired VTotal during PSR active.
This change only adds support to DC, support in amdgpu_dm is still
pending to enable this fully.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some specific TCON chip has HW limitation to support PSRSU+DSC.
[how]
Force ffu mode when DSC enabled if we detect it is the specific
model from sink OUI DPCD. And disable ABM update for this case.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Feature requires synchronization of dig, pipe, and cursor locking
between driver and DMUB fw for PSR-SU
[how]
return True if PSR-SU in the checker should_use_dmub_lock()
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When DC driver send PSR exit dmub command to DMUB FW, it might not
wait until PSR exit. Then it may hit the following deadlock situation.
1. DC driver send HW LOCK command to DMUB FW due to frame update
2. DMUB FW Set the HW lock
3. DMUB execute PSR exit sequence and stuck at polling DPG Pending
register due to the HW Lock is set
4. DC driver ask DMUB FW to unlock HW lock, but DMUB FW is polling
DPG pending register
[how]
The reason why DC driver doesn't wait until PSR exit is because some of
the PSR state machine state is not update the dc driver. So when DC
driver read back the PSR state, it take the state for PSR inactive.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current PSR SU programming margin is fixed base on FHD 60HZ
panel. If the resolution and refresh rate become higher, the time
of current margin might not cover the programming SU time.
[how]
Notice that the programming SU time is the same among different
panels.
Instead of fixing the margin with target line number, change the
margin unit to micro second which indicate the time needed for
programming SU. Then FW set the margin line number base on the
line time and margin time.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The Y-granularity panel parameter indicate the grid
pattern granularity in the Y direction for PSRSU.
[How]
Send the Y-granularity data by PSR_COPY_SETTINGS dmub command.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when driver and dmub request aux engine at the same time,
dmub grant the aux engine but driver fail. Then driver
release aux engine but doesn't clear the request bit.
Then aux engine will be occupied by driver forever.
[How]
When driver release aux engine, clear request bit as well.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
CONFIG_DRM_AMD_DC_DCN is used by pass the compilation failures, but DC
code should be OS-agnostic.
This patch fixes it by removing unnecessasry CONFIG_DRM_AMD_DC_DCN
in dce directory.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The value actual_pix_clk_100Hz is dereferencing pointer pix_clk_params
before pix_clk_params is being null checked. Fix this by assigning
pix_clk_params->requested_pix_clk_100hz to actual_pix_clk_100Hz only if
pix_clk_params is not NULL, otherwise just NULL.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a sequence in which aux arbitration
doesn't work correctly. Driver is left with
aux access after it times out waiting for access.
In future dmub fw is never granted aux access
and is stuck in a while loop.
[How]
Cancel aux request from driver after timing out.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently driver enables dmub outbox notification before oubox ISR is
registered. During boot scenario, sometimes dmub issues hpd outbox
message before driver registers ISR and those messages are missed.
[How]
Enable dmub outbox notification after outbox ISR is registered. Also,
restructured outbox enable code to call from dm layer and renamed APIs.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCUB will hang if we send a PSR unsupported set version command.
This can occur if we fall-through into the default case in the switch
statement for PSR version.
[How]
Add an unsupported check after the switch statement.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
- Adding a DM interface to enable DSC over eDP on Linux
- DSC over eDP will allow to power savings by reducing
the bandwidth required to support panel's modes
- Apply link optimization algorithm to reduce link bandwidth
when DSC is enabled
[how]
- Read eDP panel's DSC capabilities
- Apply DSC policy on eDP panel based on its DSC capabilities
- Enable DSC encoder's on the pipe
- Enable DSC on panel's side by setting DSC_ENABLE DPCD register
- Adding link optimization algorithm to reduce link rate or lane
count based
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DC we want to wait for the INBOX0 HW Lock command to ACK before
continuing. This is to ensure that the lock has been successfully
acquired before programming HW in DC.
[How]
Add interfaces to send messages on INBOX0, poll for their completation
and clear the ack.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
reduce az indirect register dump. need add az clock_gating control field
used in some project.
[how]
conditional output indrect register in the log. add clock_gating feild
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
PSR set power command wasn't setting panel instance
and command version which caused both streams
to overwrite the same PSR state.
[how]
Pass panel instance to the set power command function
and to DMUB and set command version enum
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPO is only used for DP2.0. HPO HW control should be
disable when not being used to save power.
[How]
Shutdown HPO HW control during init hw.
Shutdown HPO HW control during stream disable.
Enable HPO HW control during stream enable if DP2.0.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
For audio packet type 0x02, there are 2 Layouts:
Layout = 0 for 2 channels
and Layout = 1 for > 2 channels.
Layout will affect bandwidth check.
Currently, for HDMI FRL, Layout field isn't set and has a default value
of 0, so theoretically only 2-channel audio for audio packet type 0x02
is supported now.
How:
1. Set Layout properly according to maximum audio channel numbers for
audios with audio packet type 0x02.
2. 8ch LPCM audio is not supported for timing modes with v_active <= 576.
Reviewed-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Bing Guo <Bing.Guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When writing long AUX commands some sinks will respond will write status
update requiring source to read status.
[How]
When a write request is replied with data (AUX_ACK_M), retry a read of
write status to determine when the write is completed.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
i2c memory doesn't get set to light sleep on hw init as intended
[HOW]
Set i2c to light sleep after reg gets zeroed, ensuring memory power
control doesn't get disabled for any other DIO memory
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
PSR_STATE2b was introduced on DMCUB side, but not on the driver side,
which caused convert_psr_state helper function to return
PSR_STATE_INVALID. That caused visual lagging during state transition.
[how]
Add PSR_STATE2b to dc_psr_state and convert_psr_state
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prevent unnecessary wake up of DMCUB when ABM is enabled without PSR
enabled, driver will notify DMCUB to stop ABM's vertical interrupts
if vsync is disabled and steady state is reached.
[How]
Send inbox message to notify ABM pause based on vsync on/off
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
