Eliminates routines and data structures that were intended to allow
TIPC to route messages to other clusters. Currently, TIPC supports only
networks consisting of a single cluster within a single zone, so this
code is unnecessary.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplifies routines and data structures that were intended to allow
TIPC to support slave nodes (i.e. nodes that did not have links to
all of the other nodes in its cluster, forcing TIPC to route messages
that it could not deliver directly through a non-slave node).
Currently, TIPC supports only networks containing non-slave nodes,
so this code is unnecessary.
Note: The latest edition of the TIPC 2.0 Specification has eliminated
the concept of slave nodes entirely.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminates routines, data structures, and files that were intended
to allows TIPC to support a network containing multiple zones.
Currently, TIPC supports only networks consisting of a single cluster
within a single zone, so this code is unnecessary.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a pair of set-get routines to dcbnl for setting the negotiation
flags of the various DCB features. Conforms to the CEE flavor of DCBX
The user sets these flags (enable, advertise, willing) for each feature
to be used by the DCBX engine. The 'get' routine returns which of the
features is enabled after the negotiation.
This patch is dependent on the following patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding an optional DCBX capability and a pair for get-set routines for
setting the device DCBX mode. The DCBX capability is a bit field of
supported attributes. The user is expected to set the DCBX mode with a
subset of the advertised attributes.
This patch is dependent on the following patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCBx applications priorities can be changed dynamically. If
application stacks are expected to keep the skb priority
consistent with the dcbx priority the stack will need to
be notified when these changes occur.
This patch adds application notifiers for the stack to register
with.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds application tlv handlers. Networking stacks
may use the application priority to set the skb priority of
their stack using the negoatiated dcbx priority.
This patch provides the dcb_{get|set}app() routines for the
stack to query these parameters. Notice lower layer drivers
can use the dcbnl_ops routines if additional handling is
needed. Perhaps in the firmware case for example
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE8021Qaz is the IEEE standard version of CEE. The
standard has had enough significant changes from the CEE
version that many of the CEE attributes have no meaning
in the new spec or do not easily map to IEEE standards.
Rather then attempt to create a complicated mapping
between CEE and IEEE standards this patch adds a nested
IEEE attribute to the list of DCB attributes. The policy
is,
[DCB_ATTR_IFNAME]
[DCB_ATTR_STATE]
...
[DCB_ATTR_IEEE]
[DCB_ATTR_IEEE_ETS]
[DCB_ATTR_IEEE_PFC]
[DCB_ATTR_IEEE_APP_TABLE]
[DCB_ATTR_IEEE_APP]
...
The following dcbnl_rtnl_ops routines were added to handle
the IEEE standard,
int (*ieee_getets) (struct net_device *, struct ieee_ets *);
int (*ieee_setets) (struct net_device *, struct ieee_ets *);
int (*ieee_getpfc) (struct net_device *, struct ieee_pfc *);
int (*ieee_setpfc) (struct net_device *, struct ieee_pfc *);
int (*ieee_getapp) (struct net_device *, struct dcb_app *);
int (*ieee_setapp) (struct net_device *, struct dcb_app *);
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iscsi_tcp, ib_iser, cxgb*, be2iscsi and bnx2i do not use
the host lock and do not take the session lock against
a irq, so this patch drops the DEF_SCSI_QCMD use. Instead
we just take the session lock and disable bhs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This adds a more informative error code and message
for the iscsi scsi eh session drop paths. This allows
you to distinguish if the session was dropped due to
a connection failure vs the iscsi layer dropping
the session due to scsi eh failure processing.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In certain machines, camera devices are supplied directly
by a number of regulators. This patch add the ability to drive
these regulators directly by the soc_camera driver.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prevents checkpatch warnings generated when defining
'static const char *foo[]' arrays. It makes sense to use
const char * const * anyway since the pointers in the array
are indeed const.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the keypad controller module found on the
TC3589X devices. This driver default adds the support for
TC35893 device.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
[Some minor fixups for compilation]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Remove bt819.h from ioctl-number.txt and make a note in the header
that these ioctls are for internal use only.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The naming of the media/rds.h header suggested that it was a generic
RDS header, when in fact it is just a saa6588 module API that is
internal to the kernel.
Rename the header and the struct and defines in it to make this clear.
Also removed the header include in radio-si470x.h (not used anymore)
and from ioctl-number.txt (it's internal to the kernel and never called
from userspace).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no sense on keeping it on 2.6.38, as nobody is using it
anymore, at the kernel tree, and installing it at the userspace
API.
As two deprecated drivers still need it, move it to their internal
directories.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no sense on keeping VIDEO_V4L1 Kconfig option just because of
two deprecated drivers moved to staging scheduled to die on 2.6.39.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the core of the WL1273 FM radio driver, it connects
the two child modules. The two child drivers are
drivers/media/radio/radio-wl1273.c and sound/soc/codecs/wl1273.c.
The radio-wl1273 driver implements the V4L2 interface and communicates
with the device. The ALSA codec offers digital audio, without it only
analog audio is available.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch fixes the rc-tbs-nec table after converting
drivers/media/video/cx88 to ir-core
(commit ba7e90c9f878e0ac3c0614a5446fe5c62ccc33ec).
It is also adds two missing buttons (10- and 10+) with
its definition (KEY_10CHANNELSUP and KEY_10CHANNELSDOWN).
[mchehab@redhat.com: move keycode numbers to 0x1b8/0x1b9 as requested by the input Maintainer]
Signed-off-by: Mariusz Białończyk <manio@skyboo.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some minor comments etc which are leftover from the old naming scheme.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remote keytables had different names all over the place. Part of the fault
is due to a bad naming when rc subsystem was created, but there were lots
of old names that were still here.
Use a common standard for everything.
Patch generated by this script:
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode,rc_map_table,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_codes_,rc_map_,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_key_map,rc_map_table,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_map_table_size,rc_map_size,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The struct that describes a rc mapping had an weird and long name.
We should properly name it, to make easier for developers to work
with it, and to avoid confusion.
Basically, generated by this script:
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode_table,rc_map,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_tab,rc_map,g <$i >a && mv a $i; done
(and manually fixed where needed)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,IR_TYPE,RC_TYPE,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_type,rc_type,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Remote Controller subsystem is meant to be used not only by Infra Red
but also for similar types of Remote Controllers. The core is not specific
to Infra Red. As such, rename:
- ir-core.h to rc-core.h
- IR_CORE to RC_CORE
- namespace inside rc-core.c/rc-core.h
To be consistent with the other changes.
No functional change on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the timberdale video-in driver.
The video IP of timberdale delivers the video data via DMA.
The driver uses the DMA api to handle DMA transfers, and make use
of the V4L2 video buffers to handle buffers against user space.
If available the driver uses an encoder to get/set the video standard
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several fields on rc_dev that drivers can benefit. Allow drivers
to pass it as a parameter to the driver.
For now, the rc_dev parameter is optional. If drivers don't pass it, create
them internally. However, the best is to create rc_dev inside the drivers,
in order to fill other fields, like open(), close(), driver_name, etc.
So, a latter patch making it mandatory and changing the caller drivers is
welcome.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch merges the ir_input_dev and ir_dev_props structs into a single
struct called rc_dev. The drivers and various functions in rc-core used
by the drivers are also changed to use rc_dev as the primary interface
when dealing with rc-core.
This means that the input_dev is abstracted away from the drivers which
is necessary if we ever want to support multiple input devs per rc device.
The new API is similar to what the input subsystem uses, i.e:
rc_device_alloc()
rc_device_free()
rc_device_register()
rc_device_unregister()
[mchehab@redhat.com: Fix compilation on mceusb and cx231xx, due to merge conflicts]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: this patch were originally bundled with some renaming
stuff and with the file merges, as seen at:
https://patchwork.kernel.org/patch/291092/.
Instead of using the original approach, I wrote the rename patches and the
code merge as separate changes, then applied the difference on this patch.
This way, it is easier to see the real changes at the code, and will be easier
to merge upstream, especially if some conflict rises on the renaming patches]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx88 only depends on VIDEO_IR because it needs ir_extract_bits().
Move that function to ir-core.h and make it inline.
Lots of drivers had dependencies on VIDEO_IR when they really
wanted IR_CORE.
The only remaining drivers to depend on VIDEO_IR are bt8xx and
saa7134 (ir_rc5_timer_end is the only function exported by
ir-functions).
Rename VIDEO_IR -> IR_LEGACY to give a hint to anyone writing or
converting drivers to IR_CORE that they do not want a dependency
on IR_LEGACY.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the remaining usages of the ir_input_nokey() and
ir_input_keydown() functions provided by drivers/media/IR/ir-functions.c
by using the corresponding functionality in ir-core instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the cx88 driver (for sampling hw) to use the
decoders provided by ir-core instead of the separate ones provided
by ir-functions (and gets rid of those).
The value for MO_DDS_IO had a comment saying it corresponded to
a 4kHz samplerate. That comment was unfortunately misleading. The
actual samplerate was something like 3250Hz.
The current value has been derived by analyzing the elapsed time
between interrupts for different values (knowing that each interrupt
corresponds to 32 samples).
Thanks to Mariusz Bialonczyk <manio@skyboo.net> for testing my patches
(about one a day for two weeks!) on actual hardware.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the driver to use regulator framework instead of set_power callback.
This with gpio_reset platform data provide cleaner way to manage chip VIO,
VDD and reset signal inside the driver.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
spi/pxa2xx: register driver properly
spi/pxa2xx: add support for shared IRQ handler
spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers
arm/pxa2xx: reorgazine SSP and SPI header files
spi/pxa2xx: Add CE4100 support
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: pass of_node to spi device and set a parent device
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
ipv4: dont create routes on down devices
epic100: hamachi: yellowfin: Fix skb allocation size
sundance: Fix oopses with corrupted skb_shared_info
Revert "ipv4: Allow configuring subnets as local addresses"
USB: mcs7830: return negative if auto negotiate fails
irda: prevent integer underflow in IRLMP_ENUMDEVICES
tcp: fix listening_get_next()
atl1c: Do not use legacy PCI power management
mac80211: fix mesh forwarding
MAINTAINERS: email address change
net: Fix range checks in tcf_valid_offset().
net_sched: sch_sfq: fix allot handling
hostap: remove netif_stop_queue from init
mac80211/rt2x00: add ieee80211_tx_status_ni()
typhoon: memory corruption in typhoon_get_drvinfo()
net: Add USB PID for new MOSCHIP USB ethernet controller MCS7832 variant
net_sched: always clone skbs
ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed.
netlink: fix gcc -Wconversion compilation warning
asix: add USB ID for Logitec LAN-GTJ U2A
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: print out alloc information with KERN_DEBUG instead of KERN_INFO
kthread_work: make lockdep happy
dw_spi driver in upstream only supports PIO mode, and this patch
will support it to cowork with the Designware dma controller used
on Intel Moorestown platform, at the same time it provides a general
framework to support dw_spi core to cowork with dma controllers on
other platforms
It has been tested with a Option GTM501L 3G modem and Infenion 60x60
modem. To use DMA mode, DMA controller 2 of Moorestown has to be enabled
Also change the dma interface suggested by Linus Walleij.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
[Typo fix and renames to match intel_mid_dma renaming]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This reverts commit 4465b46900.
Conflicts:
net/ipv4/fib_frontend.c
As reported by Ben Greear, this causes regressions:
> Change 4465b46900 caused rules
> to stop matching the input device properly because the
> FLOWI_FLAG_MATCH_ANY_IIF is always defined in ip_dev_find().
>
> This breaks rules such as:
>
> ip rule add pref 512 lookup local
> ip rule del pref 0 lookup local
> ip link set eth2 up
> ip -4 addr add 172.16.0.102/24 broadcast 172.16.0.255 dev eth2
> ip rule add to 172.16.0.102 iif eth2 lookup local pref 10
> ip rule add iif eth2 lookup 10001 pref 20
> ip route add 172.16.0.0/24 dev eth2 table 10001
> ip route add unreachable 0/0 table 10001
>
> If you had a second interface 'eth0' that was on a different
> subnet, pinging a system on that interface would fail:
>
> [root@ct503-60 ~]# ping 192.168.100.1
> connect: Invalid argument
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The taskstats structure is internally aligned on 8 byte boundaries but the
layout of the aggregrate reply, with two NLA headers and the pid (each 4
bytes), actually force the entire structure to be unaligned. This causes
the kernel to issue unaligned access warnings on some architectures like
ia64. Unfortunately, some software out there doesn't properly unroll the
NLA packet and assumes that the start of the taskstats structure will
always be 20 bytes from the start of the netlink payload. Aligning the
start of the taskstats structure breaks this software, which we don't
want. So, for now the alignment only happens on architectures that
require it and those users will have to update to fixed versions of those
packages. Space is reserved in the packet only when needed. This ifdef
should be removed in several years e.g. 2012 once we can be confident
that fixed versions are installed on most systems. We add the padding
before the aggregate since the aggregate is already a defined type.
Commit 85893120 ("delayacct: align to 8 byte boundary on 64-bit systems")
previously addressed the alignment issues by padding out the pid field.
This was supposed to be a compatible change but the circumstances
described above mean that it wasn't. This patch backs out that change,
since it was a hack, and introduces a new NULL attribute type to provide
the padding. Padding the response with 4 bytes avoids allocating an
aligned taskstats structure and copying it back. Since the structure
weighs in at 328 bytes, it's too big to do it on the stack.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: Brian Rogers <brian@xyzw.org>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current packed struct implementation of unaligned access adds the
packed attribute only to the field within the unaligned struct rather than
to the struct as a whole. This is not sufficient to enforce proper
behaviour on architectures with a default struct alignment of more than
one byte.
For example, the current implementation of __get_unaligned_cpu16 when
compiled for arm with gcc -O1 -mstructure-size-boundary=32 assumes the
struct is on a 4 byte boundary so performs the load of the 16bit packed
field as if it were on a 4 byte boundary:
__get_unaligned_cpu16:
ldrh r0, [r0, #0]
bx lr
Moving the packed attribute to the struct rather than the field causes the
proper unaligned access code to be generated:
__get_unaligned_cpu16:
ldrb r3, [r0, #0] @ zero_extendqisi2
ldrb r0, [r0, #1] @ zero_extendqisi2
orr r0, r3, r0, asl #8
bx lr
Signed-off-by: Will Newton <will.newton@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The initialization function used by hci_open_dev (hci_init_req) sends
many different HCI commands. The __hci_request function should only
return when all of these commands have completed (or a timeout occurs).
Several of these commands cause hci_req_complete to be called which
causes __hci_request to return prematurely.
This patch fixes the issue by adding a new hdev->req_last_cmd variable
which is set during the initialization procedure. The hci_req_complete
function will no longer mark the request as complete until the command
matching hdev->req_last_cmd completes.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds Bluetooth Management interface events for controller
addition and removal. The events correspond to the existing HCI_DEV_REG
and HCI_DEV_UNREG stack internal events.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch implements the read_info command which is used to fetch basic
info about an adapter.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch implements the read_index_list command through which
userspace can get a list of current adapter indices.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch implements the initial read_version command that userspace
will use before any other management interface operations.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The x86 arch has shifted its use of the nmi_watchdog from a
local implementation to the global one provide by
kernel/watchdog.c. This shift has caused a whole bunch of
compile problems under different config options. I attempt to
simplify things with the patch below.
In order to simplify things, I had to come to terms with the
meaning of two terms ARCH_HAS_NMI_WATCHDOG and
CONFIG_HARDLOCKUP_DETECTOR. Basically they mean the same thing,
the former on a local level and the latter on a global level.
With the old x86 nmi watchdog gone, there is no need to rely on
defining the ARCH_HAS_NMI_WATCHDOG variable because it doesn't
make sense any more. x86 will now use the global
implementation.
The changes below do a few things. First it changes the few
places that relied on ARCH_HAS_NMI_WATCHDOG to use
CONFIG_X86_LOCAL_APIC (the former was an alias for the latter
anyway, so nothing unusual here). Those pieces of code were
relying more on local apic functionality the nmi watchdog
functionality, so the change should make sense.
Second, I removed the x86 implementation of
touch_nmi_watchdog(). It isn't need now, instead x86 will rely
on kernel/watchdog.c's implementation.
Third, I removed the #define ARCH_HAS_NMI_WATCHDOG itself from
x86. And tweaked the include/linux/nmi.h file to tell users to
look for an externally defined touch_nmi_watchdog in the case of
ARCH_HAS_NMI_WATCHDOG _or_ CONFIG_HARDLOCKUP_DETECTOR. This
changes removes some of the ugliness in that file.
Finally, I added a Kconfig dependency for
CONFIG_HARDLOCKUP_DETECTOR that said you can't have
ARCH_HAS_NMI_WATCHDOG _and_ CONFIG_HARDLOCKUP_DETECTOR. You can
only have one nmi_watchdog.
Tested with
ARCH=i386: allnoconfig, defconfig, allyesconfig, (various broken
configs) ARCH=x86_64: allnoconfig, defconfig, allyesconfig,
(various broken configs)
Hopefully, after this patch I won't get any more compile broken
emails. :-)
v3:
changed a couple of 'linux/nmi.h' -> 'asm/nmi.h' to pick-up correct function
prototypes when CONFIG_HARDLOCKUP_DETECTOR is not set.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: fweisbec@gmail.com
LKML-Reference: <1293044403-14117-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The throughput LED trigger was always active when
the radio was enabled. In most cases that's likely
the desired behaviour, but iwlwifi requires it to
be only active when one of the virtual interfaces
is actually "connected" in some way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi and other drivers like to blink their LED
based on throughput. Implement this generically in
mac80211, based on a throughput table the driver
specifies. That way, drivers can set the blink
frequencies depending on their desired behaviour
and max throughput.
All the drivers need to do is provide an LED class
device, best with blink hardware offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most keypad drivers make use of the <linux/input/matrix_keypad.h>
defined macros, structures and inline functions.
Convert omap-keypad driver to use those as well, as suggested by a
compile time warning, hardcoded into the OMAP <palt/keypad.h>.
Created against linux-2.6.37-rc5.
Tested on Amstrad Delta.
Compile tested with omap1_defconfig and omap2plus_defconfig shrinked to
board-h4.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
spinlock in kthread_worker and wait_queue_head in kthread_work both
should be lockdep sensible, so change the interface to make it
suiltable for CONFIG_LOCKDEP.
tj: comment update
Reported-by: Nicolas <nicolas.mailhot@laposte.net>
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This function has three bugs:
1) The offset should be valid most of the time, this is just
a sanity check, therefore we should use "likely" not "unlikely"
2) This is the only place where we can check for arithmetic overflow
of the pointer plus the length.
3) The existing range checks are off by one, the valid range is
skb->head to skb_tail_pointer(), inclusive.
Based almost entirely upon a patch by Ralph Loader.
Reported-by: Ralph Loader <suckfish@ihug.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a handful of missing CDBs defs that are used by TCM
persistent reservation logic in the SPC-4 defined CDB exclusion table for
registrations and reservations.
This includes a number of missing MI_* and MO_* prefixed service actions defs
for MAINTENANCE_IN and MAINTENANCE_OUT that are mentioned wrt to persistent
registration and reservation status for the SCSI Initiator Port.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The statistics for InputMegabytes and OutputMegabytes are
misnamed. They're accumulating bytes, not megabytes.
The statistic returned via /sys must be in megabytes, however,
which is what the HBA-API wants. The FCP code needs to accumulate
it in bytes and then divide by 1,000,000 (not 2^20) before it
presented via sysfs.
This affects fcoe.ko only, not fnic. The fnic driver
correctly by accumulating bytes and then converts to megabytes.
I checked that libhbalinux is using the /sys file directly without
conversion.
BTW, qla2xxx does divide by 2^20, which I'm not fixing here.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Switches using multiple-FCFs may reject FLOGI in order to
balance the load between multiple FCFs. Even though the FCF
was available, it may have more load at the point we actually
send the FLOGI.
If the FLOGI fails, select a different FCF
if possible, among those with the same priority. If no other
FCF is available, just deliver the reject to libfc for retry.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We can easily remove the tgt_flags from fc_fcp_pkt struct
and use rpriv->tgt_flags directly where needed.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The patch fixes the following situations where NOP-Out pkt is called for:
- local unsolicited NOP-Out requests (requesting no NOP-In response)
- local NOP-Out responses to unsolicited NOP-In requests
kernel panic is observed due to double session spin_lock requests; one in the
bnx2i_process_nopin_local_cmpl routine in bnx2i_hwi.c and the other in the
iscsi_put_task routine in libiscsi.c
The proposed fix is to export the currently static __iscsi_put_task() routine
and have bnx2i call it directly instead of the iscsi_put_task() routine which
holds the session spin lock.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Acked-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To date libsas has only looked at the attached sas address when
determining the formation of wide ports. The specification and some
hardware expects that phys with different addresses will not form a wide
port unless the local peer phys also match each other. Introduce a flag
to select stricter behavior at sas_register_ha() time. The flag can be
dropped once it is known that all libsas users expect the same behavior.
Current drivers just initialize this field to zero and get the
traditional behavior.
Reported-by: Patrick Thomson <patrick.s.thomson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch changes the default initial receive window to 10 mss
(defined constant). The default window is limited to the maximum
of 10*1460 and 2*mss (when mss > 1460).
draft-ietf-tcpm-initcwnd-00 is a proposal to the IETF that recommends
increasing TCP's initial congestion window to 10 mss or about 15KB.
Leading up to this proposal were several large-scale live Internet
experiments with an initial congestion window of 10 mss (IW10), where
we showed that the average latency of HTTP responses improved by
approximately 10%. This was accompanied by a slight increase in
retransmission rate (0.5%), most of which is coming from applications
opening multiple simultaneous connections. To understand the extreme
worst case scenarios, and fairness issues (IW10 versus IW3), we further
conducted controlled testbed experiments. We came away finding minimal
negative impact even under low link bandwidths (dial-ups) and small
buffers. These results are extremely encouraging to adopting IW10.
However, an initial congestion window of 10 mss is useless unless a TCP
receiver advertises an initial receive window of at least 10 mss.
Fortunately, in the large-scale Internet experiments we found that most
widely used operating systems advertised large initial receive windows
of 64KB, allowing us to experiment with a wide range of initial
congestion windows. Linux systems were among the few exceptions that
advertised a small receive window of 6KB. The purpose of this patch is
to fix this shortcoming.
References:
1. A comprehensive list of all IW10 references to date.
http://code.google.com/speed/protocols/tcpm-IW10.html
2. Paper describing results from large-scale Internet experiments with IW10.
http://ccr.sigcomm.org/drupal/?q=node/621
3. Controlled testbed experiments under worst case scenarios and a
fairness study.
http://www.ietf.org/proceedings/79/slides/tcpm-0.pdf
4. Raw test data from testbed experiments (Linux senders/receivers)
with initial congestion and receive windows of both 10 mss.
http://research.csc.ncsu.edu/netsrv/?q=content/iw10
5. Internet-Draft. Increasing TCP's Initial Window.
https://datatracker.ietf.org/doc/draft-ietf-tcpm-initcwnd/
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: handle partial result from get_user_pages
ceph: mark user pages dirty on direct-io reads
ceph: fix null pointer dereference in ceph_init_dentry for nfs reexport
ceph: fix direct-io on non-page-aligned buffers
ceph: fix msgr_init error path
The Mesh Control header only includes 0, 1 or 2 addresses. If there is
one address, it should be interpreted as Address 4. If there are 2,
they are interpreted as Addresses 5 and 6 (Address 4 being the 4th
address in the 802.11 header).
The address extension used to hold up to 3 addresses instead of the current 2.
I'm not sure which draft version changed this, but it is very unlikely that it
will change again given the state of the approval process of this draft. See
section 7.1.3.6.3 in current draft (8.0).
Also, note that the extra address that I'm removing was not being used, so this
change has no effect on over-the-air frame formats. But I thought I better
remove it before someone does start using it.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export the information which antennas are available for configuration as TX or
RX antennas via nl80211.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As has been pointed out by Daniel Halperin some devices (e.g. Intel IWL5100)
can only TX from a subset of RX antennas, so use separate availability masks
for RX and TX.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative. Also in the same patch, allow userspace to add
information elements to mesh beacons. This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh parameters can be to setup a mesh or to configure it.
This patch renames the ambiguous name mesh_params to mesh_config
in preparation for mesh_setup.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All rt2x00 drivers except rt2800pci call ieee80211_tx_status() from
a workqueue, which causes "NOHZ: local_softirq_pending 08" messages.
To fix it, add ieee80211_tx_status_ni() similar to ieee80211_rx_ni()
which can be called from process context, and call it from
rt2x00lib_txdone(). For the rt2800pci special case a driver
flag is introduced.
https://bugzilla.kernel.org/show_bug.cgi?id=24892
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Flush the routing cache only of entries that match the
network namespace in which the purge event occurred.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] gspca - sonixj: Better handling of the bridge registers 0x01 and 0x17
[media] gspca - sonixj: Add the bit definitions of the bridge reg 0x01 and 0x17
[media] gspca - sonixj: Set the flag for some devices
[media] gspca - sonixj: Add a flag in the driver_info table
[media] gspca - sonixj: Fix a bad probe exchange
[media] gspca - sonixj: Move bridge init to sd start
[media] bttv: remove unneeded locking comments
[media] bttv: fix mutex use before init (BZ#24602)
[media] Don't export format_by_forcc on two different drivers
Pawel reported a panic related to handling shared skbs in ixgbe
incorrectly. So we need to revert my previous patch to work around
this bug. Instead of reverting the patch completely, I just revert
the essential lines, so we can add the previous optimization
back more easily in future.
commit 3511c9132f
Author: Changli Gao <xiaosuo@gmail.com>
Date: Sat Oct 16 13:04:08 2010 +0000
net_sched: remove the unused parameter of qdisc_create_dflt()
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix cciss_revalidate panic
block: max hardware sectors limit wrapper
block: Deprecate QUEUE_FLAG_CLUSTER and use queue_limits instead
blk-throttle: Correct the placement of smp_rmb()
blk-throttle: Trim/adjust slice_end once a bio has been dispatched
block: check for proper length of iov entries earlier in blk_rq_map_user_iov()
drbd: fix for spin_lock_irqsave in endio callback
drbd: don't recvmsg with zero length
The cnt32_to_63 algorithm relies on proper counter data evaluation
ordering to work properly. This was missing from the provided
documentation.
Let's augment the documentation with the missing usage constraint and
fix the only instance that got it wrong.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Silence warnings such as -
drivers/video/s1d13xxxfb.c:421: warning: ‘bltbit_wait_bitset’ defined but not used
Just drop the unused code.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Today, userspace sets up an input device based on the data it emits.
This is not always enough; a tablet and a touchscreen may emit exactly
the same data, for instance, but the former should be set up with a
pointer whereas the latter does not need to. Recently, a new type of
touchpad has emerged where the buttons are under the pad, which
changes logic without changing the emitted data. This patch introduces
a new ioctl, EVIOCGPROP, which enables user access to a set of device
properties useful during setup. The properties are given as a bitmap
in the same fashion as the event types, and are also made available
via sysfs, uevent and /proc/bus/input/devices.
Acked-by: Ping Cheng <pingc@wacom.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
This patch modifies IPsec6 to fragment IPv6 packets that are
locally generated as needed.
This version of the patch only fragments in tunnel mode, so that fragment
headers will not be obscured by ESP in transport mode.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix the irqtime code for 32bit
sched: Fix the irqtime code to deal with u64 wraps
nohz: Fix get_next_timer_interrupt() vs cpu hotplug
Sched: fix skip_clock_update optimization
sched: Cure more NO_HZ load average woes
Add block identifier to be able to add multiple mfd clients
to the mfd core
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Most of the register layout, client IRQ numbers on the TC35892 is shared also
by other variants. Make this generic as tc3589x
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the header file to include further variants within
the same mfd core driver
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86: avoid high BIOS area when allocating address space
x86: avoid E820 regions when allocating address space
x86: avoid low BIOS area when allocating address space
resources: add arch hook for preventing allocation in reserved areas
Revert "resources: support allocating space within a region from the top down"
Revert "PCI: allocate bus resources from the top down"
Revert "x86/PCI: allocate space from the end of a region, not the beginning"
Revert "x86: allocate space within a region top-down"
Revert "PCI: fix pci_bus_alloc_resource() hang, prefer positive decode"
PCI: Update MCP55 quirk to not affect non HyperTransport variants
Generic code to provide new per cpu atomic features
this_cpu_cmpxchg
this_cpu_xchg
Fallback occurs to functions using interrupts disable/enable
to ensure correct per cpu atomicity.
Fallback to regular cmpxchg and xchg is not possible since per cpu atomic
semantics include the guarantee that the current cpus per cpu data is
accessed atomically. Use of regular cmpxchg and xchg requires the
determination of the address of the per cpu data before regular cmpxchg
or xchg which therefore cannot be atomically included in an xchg or
cmpxchg without segment override.
tj: - Relocated new ops to conform better to the general organization.
- This patch contains a trivial comment fix.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The fix in commit #6a0cc49 requires more than three concurrent instances
of synchronize_sched_expedited() before batching is possible. This
patch uses a ticket-counter-like approach that is also not unrelated to
Lai Jiangshan's Ring RCU to allow sharing of expedited grace periods even
when there are only two concurrent instances of synchronize_sched_expedited().
This commit builds on Tejun's original posting, which may be found at
http://lkml.org/lkml/2010/11/9/204, adding memory barriers, avoiding
overflow of signed integers (other than via atomic_t), and fixing the
detection of batching.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
$ cat << EOF | gcc -Wconversion -xc -S -o/dev/null -
unsigned f(void) {return NLMSG_HDRLEN;}
EOF
<stdin>: In function 'f':
<stdin>:3:26: warning: negative integer implicitly converted to unsigned type
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds arch_remove_reservations(), which an arch can implement if it
needs to protect part of the address space from allocation.
Sometimes that can be done by just putting a region in the resource tree,
but there are cases where that doesn't work well. For example, x86 BIOS
E820 reservations are not related to devices, so they may overlap part of,
all of, or more than a device resource, so they may not end up at the
correct spot in the resource tree.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For read operation, we have to set the argument _write_ of get_user_pages
to 1 since we will write data to pages. Also, we need to SetPageDirty before
releasing these pages.
Signed-off-by: Henry C Chang <henry_c_chang@tcloudcomputing.com>
Signed-off-by: Sage Weil <sage@newdream.net>
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Fix pm_runtime_suspended()
PM / Hibernate: Restore old swap signature to avoid user space breakage
PM / Hibernate: Fix PM_POST_* notification with user-space suspend
- include/linux/percpu.h: this_cpu_add_return() and friends were
located next to __this_cpu_add_return(). However, the overall
organization is to first group by preemption safeness. Relocate
this_cpu_add_return() and friends to preemption-safe area.
- arch/x86/include/asm/percpu.h: Relocate percpu_add_return_op() after
other more basic operations. Relocate [__]this_cpu_add_return_8()
so that they're first grouped by preemption safeness.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Use this_cpu operations to optimize access primitives for highmem.
The main effect is the avoidance of address calculations through the
use of a segment prefix.
V3->V4
- kmap_atomic_idx: Do not return a value.
- Use __this_cpu_dec without HIGHMEM_DEBUG
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Introduce generic support for this_cpu_add_return etc.
The fallback is to realize these operations with simpler __this_cpu_ops.
tj: - Reformatted __cpu_size_call_return2() to make it more consistent
with its neighbors.
- Dropped unnecessary temp variable ret__ from
__this_cpu_generic_add_return().
Reviewed-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
__get_cpu_var() can be replaced with this_cpu_read and will then use a
single read instruction with implied address calculation to access the
correct per cpu instance.
However, the address of a per cpu variable passed to __this_cpu_read()
cannot be determined (since it's an implied address conversion through
segment prefixes). Therefore apply this only to uses of __get_cpu_var
where the address of the variable is not used.
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Hugh Dickins <hughd@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use this_cpu ops in various places to optimize per cpu data access.
Cc: Jason Baron <jbaron@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Implement blk_limits_max_hw_sectors() and make
blk_queue_max_hw_sectors() a wrapper around it.
DM needs this to avoid setting queue_limits' max_hw_sectors and
max_sectors directly. dm_set_device_limits() now leverages
blk_limits_max_hw_sectors() logic to establish the appropriate
max_hw_sectors minimum (PAGE_SIZE). Fixes issue where DM was
incorrectly setting max_sectors rather than max_hw_sectors (which
caused dm_merge_bvec()'s max_hw_sectors check to be ineffective).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When stacking devices, a request_queue is not always available. This
forced us to have a no_cluster flag in the queue_limits that could be
used as a carrier until the request_queue had been set up for a
metadevice.
There were several problems with that approach. First of all it was up
to the stacking device to remember to set queue flag after stacking had
completed. Also, the queue flag and the queue limits had to be kept in
sync at all times. We got that wrong, which could lead to us issuing
commands that went beyond the max scatterlist limit set by the driver.
The proper fix is to avoid having two flags for tracking the same thing.
We deprecate QUEUE_FLAG_CLUSTER and use the queue limit directly in the
block layer merging functions. The queue_limit 'no_cluster' is turned
into 'cluster' to avoid double negatives and to ease stacking.
Clustering defaults to being enabled as before. The queue flag logic is
removed from the stacking function, and explicitly setting the cluster
flag is no longer necessary in DM and MD.
Reported-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
tty: add 'active' sysfs attribute to tty0 and console device
Userspace can query the actual virtual console, and the configured
console devices behind /dev/tt0 and /dev/console.
The last entry in the list of devices is the active device, analog
to the console= kernel command line option.
The attribute supports poll(), which is raised when the virtual
console is changed or /dev/console is reconfigured.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
index 0000000..b138b66
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
fanotify: fill in the metadata_len field on struct fanotify_event_metadata
fanotify: split version into version and metadata_len
fanotify: Dont try to open a file descriptor for the overflow event
fanotify: Introduce FAN_NOFD
fanotify: do not leak user reference on allocation failure
inotify: stop kernel memory leak on file creation failure
fanotify: on group destroy allow all waiters to bypass permission check
fanotify: Dont allow a mask of 0 if setting or removing a mark
fanotify: correct broken ref counting in case adding a mark failed
fanotify: if set by user unset FMODE_NONOTIFY before fsnotify_perm() is called
fanotify: remove packed from access response message
fanotify: deny permissions when no event was sent
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (28 commits)
MIPS: Add a CONFIG_FORCE_MAX_ZONEORDER Kconfig option.
MIPS: LD/SD o32 macro GAS fix update
MIPS: Alchemy: fix build with SERIAL_8250=n
MIPS: Rename mips_dma_cache_sync back to dma_cache_sync
MIPS: MT: Fix typo in comment.
SSB: Fix nvram_get on BCM47xx platform
MIPS: BCM47xx: Swap serial console if ttyS1 was specified.
MIPS: BCM47xx: Use sscanf for parsing mac address
MIPS: BCM47xx: Fill values for b43 into SSB sprom
MIPS: BCM47xx: Do not read config from CFE
MIPS: FDT size is a be32
MIPS: Fix CP0 COUNTER clockevent race
MIPS: Fix regression on BCM4710 processor detection
MIPS: JZ4740: Fix pcm device name
MIPS: Separate two consecutive loads in memset.S
MIPS: Send proper signal and siginfo on FP emulator faults.
MIPS: AR7: Fix loops per jiffies on TNETD7200 devices
MIPS: AR7: Fix double ar7_gpio_init declaration
MIPS: Rework GENERIC_HARDIRQS Kconfig.
MIPS: Alchemy: Add return value check for strict_strtoul()
...
Introduce skb_checksum_start_offset() to replace repetitive calculation.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Special care is taken inside sk_port_alloc to avoid overwriting
skc_node/skc_nulls_node. We should also avoid overwriting
skc_bind_node/skc_portaddr_node.
The patch fixes the following crash:
BUG: unable to handle kernel paging request at fffffffffffffff0
IP: [<ffffffff812ec6dd>] udp4_lib_lookup2+0xad/0x370
[<ffffffff812ecc22>] __udp4_lib_lookup+0x282/0x360
[<ffffffff812ed63e>] __udp4_lib_rcv+0x31e/0x700
[<ffffffff812bba45>] ? ip_local_deliver_finish+0x65/0x190
[<ffffffff812bbbf8>] ? ip_local_deliver+0x88/0xa0
[<ffffffff812eda35>] udp_rcv+0x15/0x20
[<ffffffff812bba45>] ip_local_deliver_finish+0x65/0x190
[<ffffffff812bbbf8>] ip_local_deliver+0x88/0xa0
[<ffffffff812bb2cd>] ip_rcv_finish+0x32d/0x6f0
[<ffffffff8128c14c>] ? netif_receive_skb+0x99c/0x11c0
[<ffffffff812bb94b>] ip_rcv+0x2bb/0x350
[<ffffffff8128c14c>] netif_receive_skb+0x99c/0x11c0
Signed-off-by: Leonard Crestez <lcrestez@ixiacom.com>
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some windows versions have wrong RFC1323 implementations, with SYN and
SYNACKS messages containing zero tcp timestamps.
We relaxed in commit fc1ad92dfc the passive connection case
(Windows connects to a linux machine), but the reverse case (linux
connects to a Windows machine) has an analogue problem when tsvals from
windows machine are 'negative' (high order bit set) : PAWS triggers and
we drops incoming messages.
Fix this by making zero ts_recent value special, allowing frame to be
processed.
Based on a report and initial patch from Dmitiy Balakin
Bugzilla reference : https://bugzilla.kernel.org/show_bug.cgi?id=24842
Reported-by: dmitriy.balakin@nicneiron.ru
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dev_close_many and dev_deactivate_many to factorize another
sync-rcu operation on the netdevice unregister path.
$ modprobe dummy numdummies=10000
$ ip link set dev dummy* up
$ time rmmod dummy
Without the patch With the patch
real 0m 24.63s real 0m 5.15s
user 0m 0.00s user 0m 0.00s
sys 0m 6.05s sys 0m 5.14s
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the calcualation of the Tx hash for a given hash range into a separate
function and define the skb_tx_hash(), which calculates a Tx hash for a
[0; dev->real_num_tx_queues - 1] hash values range, using this
function (__skb_tx_hash()).
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid unbalanced IRQ wake disable, ensure that wakeups are disabled
only when wakeups have been successfully enabled.
Tested on OMAP3630SDP/ZOOM3.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Reported-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix various typos and other errors in comments of tty_driver.h. The most
significant is the wrong name of a function for the description of
TTY_DRIVER_DYNAMIC_DEV.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new notification to indicate that a received, unprotected
Deauthentication or Disassociation frame was dropped due to
management frame protection being in use. This notification is
needed to allow user space (e.g., wpa_supplicant) to implement
SA Query procedure to recover from association state mismatch
between an AP and STA.
This is needed to avoid getting stuck in non-working state when MFP
(IEEE 802.11w) is used and a protected Deauthentication or
Disassociation frame is dropped for any reason. After that, the
station would silently discard any unprotected Deauthentication or
Disassociation frame that could be indicating that the AP does not
have association for the STA (when the Reason Code would be 6 or 7).
IEEE Std 802.11w-2009, 11.13 describes this recovery mechanism.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nvram_get function was never in the mainline kernel, it only existed in
an external OpenWrt patch. Use nvram_getenv function, which is in mainline
and use an include instead of an extra function declaration. et0macaddr
contains the mac address in text from like 00:11:22:33:44:55. We have to
parse it before adding it into macaddr.
nvram_parse_macaddr will be merged into asm/mach-bcm47xx/nvram.h through
the MIPS git tree and will be available soon. It will not build now without
nvram_parse_macaddr, but it hasn't before either.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: mb@bu3sch.de
Cc: netdev@vger.kernel.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Buesch <mb@bu3sch.de>
Patchwork: https://patchwork.linux-mips.org/patch/1849/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: define separate EVIOCGKEYCODE_V2/EVIOCSKEYCODE_V2
Input: wacom - add another Bamboo Pen ID (0xd4)
There are some situations (e.g. in __pm_generic_call()), where
pm_runtime_suspended() is used to decide whether or not to execute
a device's (system) ->suspend() callback. The callback is not
executed if pm_runtime_suspended() returns true, but it does so
for devices that don't even support runtime PM, because the
power.disable_depth device field is ignored by it. This leads to
problems (i.e. devices are not suspened when they should), so rework
pm_runtime_suspended() so that it returns false if the device's
power.disable_depth field is different from zero.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
Simple sysfs emumeration of the PMUs.
Use a "event_source" bus, and add PMU devices using their name.
Each PMU device has a type attribute which contrains the value needed
for perf_event_attr::type to identify this PMU.
This is the minimal stub needed to start using this interface,
we'll consider extending the sysfs usage later.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20101117222056.316982569@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Extend the perf_pmu_register() interface to allow for named and
dynamic pmu types.
Because we need to support the existing static types we cannot use
dynamic types for everything, hence provide a type argument.
If we want to enumerate the PMUs they need a name, provide one.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20101117222056.259707703@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Touch devices capable of hovering, i.e., fingers detected a
distance from the surface, are not supported by the current
input MT protocol. This patch adds ABS_MT_DISTANCE, which may
be used to indicate the distance between the contact and the
surface.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The drivers using the type B protocol all report tracking information
the same way. The contact id is semantically equivalent to
ABS_MT_SLOT, and the handling of ABS_MT_TRACKING_ID only complicates
the driver. The situation can be improved upon by providing a common
pointer emulation code, thereby removing the need for the tracking id
in the driver. This patch moves all tracking event handling over to
the input core, simplifying both the existing drivers and the ones
currently in preparation.
Acked-by: Ping Cheng <pingc@wacom.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The MT slots devices all follow the same initialization pattern
of creating slots and hinting about buffer size. Let drivers call
an initialization function instead, and make sure it can be called
repeatedly without side effects.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
In preparation for common code to handle a larger set of MT slots
devices, move the slots handling over to a separate file.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Allow drivers or rate control algorithms to specify BlockAck session
timeout when initiating an ADDBA transaction. This is useful in cases
where maintaining persistent BA sessions does not incur any overhead.
The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc
drivers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the upcoming hardware offload implementation,
some devices will have a different maximum duration
for the remain-on-channel command. Advertise the
maximum duration in mac80211, and make mac80211 set
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
