IS_ERR_VALUE macro should be used only with unsigned long type.
Specifically it works incorrectly with longer types.
The patch follows conclusion from discussion on LKML [1][2].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2120927
[2]: http://permalink.gmane.org/gmane.linux.kernel/2150581
[ralf@linux-mips.org: While it may not immediately be obvious, the type
of st_value in the end is an unsigned long equivalent so the invocation
of IS_ERR_VALUE() was valid but I'm applying the patch anyway for
clarity.]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12553/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Propagate sNaN payload in quieting in the legacy-NaN mode as well. If
clearing the quiet bit would produce infinity, then set the next lower
trailing significand field bit, matching the SB-1 and BMIPS5000 hardware
implementations. Some other MIPS FPU hardware implementations do
produce the default qNaN bit pattern instead.
This reverts some changes made for semantics preservation with commit
dc3ddf42 [MIPS: math-emu: Update sNaN quieting handlers], consequently
bringing back most of the semantics from before commit fdffbafb [Lots of
FPU bug fixes from Kjeld Borch Egevang.], except from the qNaN produced
in the infinity case. Previously the default qNaN bit pattern was
produced in that case.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11483/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update the ELF personality macros used for individual ABIs to make
actions in the same order across all of them and match formatting too.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 8cb48fe169 ("MIPS: Provide correct siginfo_t.si_stime"),
MIPS' uapi/asm/siginfo.h has included uapi/asm-generic/siginfo.h
directly before defining MIPS' struct siginfo, in order to get the
necessary definitions needed for the siginfo struct without the generic
copy_siginfo() hitting compiler errors due to struct siginfo not yet
being defined.
Now that the generic copy_siginfo() is moved out to linux/signal.h we
can safely include asm-generic/siginfo.h before defining the MIPS
specific struct siginfo, which avoids the uapi/ include as well as
breakage due to generic copy_siginfo() being defined before struct
siginfo.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 8cb48fe169 ("MIPS: Provide correct siginfo_t.si_stime")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Petr Malat <oss@malat.biz>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.0-
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.
It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.
Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Petr Malat <oss@malat.biz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christopher Ferris <cferris@google.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.0-
Patchwork: https://patchwork.linux-mips.org/patch/12478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Just to ease debugging of multiplatform kernel, make sure we print
"Broadcom BMIPS5200" for the BMIPS5200 implementation instead of
Broadcom BMIPS5000.
Fixes: 68e6a78373 ("MIPS: BMIPS: Add PRId for BMIPS5200 (Whirlwind)")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13014/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BMIPS_GENERIC being multiplatform and intended to support BMIPS3200,
BMIPS3300, BMIPS4350, BMIPS4380 and BMIPS5000-class processors, there is
not much more we can put in there since they do not share the same I and
D cache line sizes at all (doubled for every new generation
essentially), some processors have a S-cache, some don't, some have a
FPU, some don't.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13013/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
local_r4k___flush_cache_all() is missing a special check for BMIPS5000
processors, we need to blast the S-cache, just like other MTI processors
since we have an inclusive cache. We also need an additional __sync() to
make sure this is completed.
Fixes: d74b0172e4 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13012/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BMIPS5000 and BMIPS5200 processor have no D cache aliases, and this is
properly handled by the per-CPU override added at the end of
r4k_cache_init(), the problem is that the output of probe_pcache()
disagrees with that, since this is too late:
Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
With the change moved earlier, we now have a consistent output with the
settings we are intending to have:
Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, VIPT, no aliases, linesize 32 bytes
Fixes: d74b0172e4 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BMIPS5000 and BMIPS52000 processors have their I-cache filling from the
D-cache. Since BMIPS_GENERIC does not provide (yet) a
cpu-feature-overrides.h file, this was not set anywhere, so make sure
the R4K cache detection takes care of that.
Fixes: d74b0172e4 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13010/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable CONFIG_MTD_BCM63XX_PARTS in arch/mips/configs/bmips_be_defconfig
since this is a necessary option to parse the built-in flash partition
table on BMIPS big-endian SoCs (Cable Modem and DSL).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12256/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
... making upstream development binutils snapshots work as expected,
e.g.:
$ mips64el-linux-ld --version
GNU ld (GNU Binutils) 2.20.1.20100303
[...]
$
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Acked-by: Michal Marek <mmarek@suse.cz>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kbuild@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12537/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixes wrong bcm7425 SATA AHCI hardware interrupt property value with
periph_intc and SATA PHY unit address, and removes needless
brcm,broken-{ncq,phy} properties what are not used anywhere.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Dragan Stancevic <dragan.stancevic@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/13017/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When debugging a relocated kernel, the addresses of the relocated
symbols and the offset applied is essential information. If the kernel
is compiled with debugging information, then print this information
during bootup using the same function as the panic notifier.
[ralf@linux-mips.org: Fixed spelling mistake pointed out by
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>.]
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12989/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds KASLR to the MIPS kernel.
Entropy is derived from the banner, which will change every build and
random_get_entropy() which should provide additional runtime entropy.
Additionally the bootloader may pass entropy via the /chosen/kaslr-seed
node in device tree.
The kernel is relocated by up to RANDOMIZE_BASE_MAX_OFFSET bytes from
its link address (PHYSICAL_START). Because relocation happens so early
in the kernel boot, the amount of physical memory has not yet been
determined. This means the only way to limit relocation within the
available memory is via Kconfig.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12990/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Early access to the kernel command line requires early access to the FDT
for platforms which pass the command line within the device tree. There
was no common way to retrieve the location of the FDT without incurring
side effects, such as plat_mem_setup which, on Malta at least,
initializes a bunch of other stuff.
This patch adds plat_get_ftd() for IMG platforms.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12988/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel reserves all memory before the _end symbol as bootmem,
however, once the kernel can be relocated elsewhere in memory this may
result in a large amount of wasted memory. The assumption is that the
memory between the link and relocated address of the kernel may be
released back to the available memory pool.
Memory statistics for a Malta with the kernel relocating by
16Mb, without the patch:
Memory: 105952K/131072K available (4604K kernel code, 242K rwdata,
892K rodata, 1280K init, 183K bss, 25120K reserved, 0K cma-reserved)
And with the patch:
Memory: 122336K/131072K available (4604K kernel code, 242K rwdata,
892K rodata, 1280K init, 183K bss, 8736K reserved, 0K cma-reserved)
The 16Mb offset is removed from the reserved region and added back to
the available region.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12986/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If CONFIG_RELOCATABLE is enabled, call relocate_kernel.
This function will return the entry point of the relocated kernel if
copy/relocate is sucessful or the original entry point if not. The stack
pointer must then be pointed into the new image.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12984/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/kernel/relocate.c contains the functions necessary to relocate
the kernel elsewhere in memory
The kernel makes a copy of itself at the new address. It uses the
relocation table inserted by the relocs tool to fix symbol references
within the new image.
If copy/relocation is sucessful then the entry point of the new kernel
is returned, otherwise fall back to starting the kernel in place.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12985/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When CONFIG_RELOCATABLE is enabled (added in later patch) add
--emit-relocs to vmlinux LDFLAGS so that fully linked vmlinux contains
relocation information.
Run the previously added relocs tool to fill in the .data.relocs section
of vmlinux with a table of relocations. The relocs tool will also remove
(mark as 0 length) the relocation sections added to vmlinux.
When vmlinux is passed to the boot makefile for conversion into a boot
image the now empty relocation sections will be removed and the
populated relocation table will be included in the binary image.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12983/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When CONFIG_RELOCATABLE is enabled, add a new section in the memory map
to be filled with relocation data.
CONFIG_RELOCATION_TABLE_SIZE allows the amount of space reserved to be
adjusted if necessary.
The relocs tool will populate this reserved space with relocation
information. The space is reserved within the elf by filling it with
0's, and an invalid entry is left at the start of the space such that
kernel relocation will be aborted if the table is empty.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12982/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This tool is based on the x86/boot/tools/relocs tool.
It parses the relocations present in the vmlinux elf file, building a
table of relocations that will be necessary to run the kernel from an
address other than its link address. This table is inserted into the
vmlinux elf, in the .data.relocs section. The table is subsequently used
by the code in arch/mips/kernel/relocate.c (added later) to relocate the
kernel.
The tool, by default, also marks all relocation sections as 0 length.
This is due to objcopy currently being unable to handle copying the
relocations between 64 and 32 bit elf files as is done when building a
64 bit kernel.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12981/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Previously the seccomp would only support strict mode on O32 userland
programs when the kernel had support for both O32 and N32 ABIs. Remove
kludge and support both ABIs.
With this patch in place, the seccomp_bpf self test now passes
global.mode_strict_support with N32 userland.
Suggested-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12917/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move retrieval of compat syscall numbers into inline function defined in
asm-generic header so that arches may override it.
[ralf@linux-mips.org: Resolve merge conflict.]
Suggested-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will Drewry <wad@chromium.org>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12978/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit d218af7849 ("MIPS: scall: Always run the seccomp syscall
filters") modified the syscall code to always call the seccomp filters,
but missed the case where a filter may redirect the syscall, as
revealed by the seccomp_bpf self test.
The syscall path now restores the syscall from the stack after the
filter rather than saving it locally. Syscall number checking and
syscall function table lookup is done after the filter may have run such
that redirected syscalls are also checked, and executed.
The regular path of syscall number checking and pointer lookup is also
made more consistent between ABIs with scall64-64.S being the reference.
With this patch in place, the seccomp_bpf self test now passes
TRACE_syscall.syscall_redirected and TRACE_syscall.syscall_dropped on
all MIPS ABIs.
Fixes: d218af7849 ("MIPS: scall: Always run the seccomp syscall filters")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Eric B Munson <emunson@akamai.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12916/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The seccomp_bpf self test revealed that a 64bit kernel delivered an
invalid SIG_SYS to a 32bit userspace, because it was falling into the
default of the switch statement. Add a case to handle delivering the
signal.
With this patch, the seccomp_bpf self test now passes the TRAP.handler
case with O32 and N32 userlands.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Amanieu d'Antras <amanieu@gmail.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12915/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds self-test support on MIPS, based on RFC patch from Kees Cook.
Modifications from the RFC:
- support the O32 syscall which passes the real syscall number in a0.
- Use PTRACE_{GET,SET}REGS
- Because SYSCALL_NUM and SYSCALL_RET are the same register, it is not
possible to test modifying the syscall return value when skipping,
since both would need to set the same register. Therefore modify that
test case to just detect the skipped test.
Tested on MIPS32r2 / MIPS64r2 with O32, N32 and N64 userlands.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Will Drewry <wad@chromium.org>
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12977/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
