Evalation of the WM5102 has identified a number of register values which
should be written after SYSCLK is enabled on revision A in order to
improve performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many Arizona class devices contain ADSP2 cores with a standard method for
hooking them into the audio map. Define standard helpers for this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many current Wolfson devices feature DSPs based around an architecture
known as ADSP. Since there is a lot of commonality in the system
integration of these devices a common library will be used to provide
support for them.
This version provides equivalent support for ADSP1 to that currently
included in the WM2200 driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use regmap-mmio instead of open-coding caching and register accessors.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use devm_request_and_ioremap for requesting and mapping the IO region. This
makes the code a bit smaller and simpler.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add dB TLV ranges for the various volume controls.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ARIZONA_MICB1_ENA_SHIFT was used for micbias 2 and 3. This change
correctly uses the ARIZONA_MICBX_ENA_SHIFT for each corresponding DAPM
supply. This should not have caused any problems as the micbias enables
are in the same place in each register.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than always assuming the maximum possible BCLK rate will be
required generate BCLKs for stereo if either one or two channels is
enabled. In order to support this we also need to ensure that only
the relevant channels are enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When lowering SYSCLK to 50kHz for accessory detection also lower the
AIFnCLK divisor to normalise the clocking configuration within the
device. This will not disrupt audio as we cannot support active audio
with such a low SYSCLK.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix wm2200.c printk format warnings (seen on x86_64):
sound/soc/codecs/wm2200.c:1027:4: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
sound/soc/codecs/wm2200.c:1139:5: warning: format '%d' expects type 'int', but argument 5 has type 'long unsigned int'
sound/soc/codecs/wm2200.c:1181:2: warning: format '%d' expects type 'int', but argument 7 has type 'size_t'
sound/soc/codecs/wm2200.c:1201:5: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
sound/soc/codecs/wm2200.c:1264:4: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
sound/soc/codecs/wm2200.c:1328:5: warning: format '%d' expects type 'int', but argument 5 has type 'long unsigned int'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch DAPMises headphone and lineout output enable controls.
Earlier these output enable bits were permanently turned on in probe.
In da9055 codec, right outmixer is directly connected with right HP and
Line out. This resulted in two side effects,
(1) When you only want to use lineout, right HP (and connected charge
pump) also gets enabled
(2) When you only want to use stereo HP, lineout also gets enabled
This patch adds three switches to select which output(s) should be
enabled.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Nothing too exciting except for the ams-delta change which is relatively
lerge due to the fact that the driver loading had been totally broken as
the driver needed a newer API to function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lEIC
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.7
Nothing too exciting except for the ams-delta change which is relatively
lerge due to the fact that the driver loading had been totally broken as
the driver needed a newer API to function.
A bunch of updates to the regmap range support, the most important ones
being to rename "n_ranges" to "num_ranges" for consistency and to allow
block writes to cross page boundaries, making things more transparent.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Cdf2
-----END PGP SIGNATURE-----
Merge tag 'regmap/range' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-wm2200
regmap: Range API changes
A bunch of updates to the regmap range support, the most important ones
being to rename "n_ranges" to "num_ranges" for consistency and to allow
block writes to cross page boundaries, making things more transparent.
As of commit 99c2aa (firmware loader: fix creation failure of fw loader
device) we can have more than one firmware request outstanding at once so
there is no need to daisychain our requests any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This can be used to provide some additional settling time to ensure that
we don't start microphone detection while the microphone pin is connected
to one of the headphone pins.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is more idiomatic and ensures we don't try to do the ASoC card setup
until we've got all the required resources.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the device is now idle_bias_off these never have any useful effect,
the device will be brought to _OFF when idle, and will at best leave it
powered for longer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit add a sound codec driver for Silicon Laboratories 476x
series of AM/FM radio chips.
Signed-off-by: Andrey Smirnov <andrey.smirnov@convergeddevices.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds AIF DSP mode support for da9055 codec driver.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The CS4271 has a feature to sync its analog mute flags, so one mute
circuitry can be used for both channels.
Give users access to this feature with a new DT property and a flag in
the platform data.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch slightly improves ALC calibration process of da9055 codec
driver by muting Mic PGAs during calibration.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support of
D3 clock-stop. Also changing the power_save option in sysfs kicks
off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in HD-audio
are continued cleanups and standardization for the generic auto
parser and bug fixes (HBR, device-specific fixups), in addition to
the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=uNqD
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support
of D3 clock-stop. Also changing the power_save option in sysfs
kicks off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in
HD-audio are continued cleanups and standardization for the generic
auto parser and bug fixes (HBR, device-specific fixups), in
addition to the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode."
Fix up various arm soc header file reorg conflicts.
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (339 commits)
ALSA: hda - Add new codec ALC283 ALC290 support
ALSA: hda - avoid unneccesary indices on "Headphone Jack" controls
ALSA: hda - fix indices on boost volume on Conexant
ALSA: aloop - add locking to timer access
ALSA: hda - Fix hang caused by race during suspend.
sound: Remove unnecessary semicolon
ALSA: hda/realtek - Fix detection of ALC271X codec
ALSA: hda - Add inverted internal mic quirk for Lenovo IdeaPad U310
ALSA: hda - make Realtek/Sigmatel/Conexant use the generic unsol event
ALSA: hda - make a generic unsol event handler
ASoC: codecs: Add DA9055 codec driver
ASoC: eukrea-tlv320: Convert it to platform driver
ALSA: ASoC: add DT bindings for CS4271
ASoC: wm_hubs: Ensure volume updates are handled during class W startup
ASoC: wm5110: Adding missing volume update bits
ASoC: wm5110: Add OUT3R support
ASoC: wm5110: Add AEC loopback support
ASoC: wm5110: Rename EPOUT to HPOUT3
ASoC: arizona: Add more clock rates
ASoC: arizona: Add more DSP options for mixer input muxes
...
Allow a coefficient set provided using the Wolfson callibration tools to
be provided along with the firmware files. Currently only coefficient
files which configure absolute register addresses are supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the regmap ranges support to add the WM2200 DSP core memory pages
into the "register map" beyond the end of the real register map. We
don't extend beyond 16 bits since the regmap API will iterate over
every register doing diagnostics.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes commit: 805238b ASoC: twl6040: Convert to use DAI DAPM widgets
where the connection between the stream widgets and the ADC widgets was
reversed and because of this on capture the DAPM is not powering up the
codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=q7ZY
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
This patch adds support for Dialog semiconductor's DA9055 audio codec.
This has been tested on DA9055 EVB with Samsung SMDK6410 board.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Apart from pure matching, the bindings also support setting the the
reset gpio line.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In some circumstances we may need to flush volume updates to the device
after switching to class W mode. Do this unconditionally to ensure that
these situations are handled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The volume update bits were being set on all but one input and one output.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The third output on WM5110 is a general purpose headphone output which can
be used to drive an earpice rather than a dedicated earpiece driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We never set the GPIO from atomic context so there's no reason why we
can't support a GPIO that needs to sleep when configuring.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to cs4270 datasheet, there is no reference to mono mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the kernel has been booted with DT blob the platform data is NULL for
the driver.
We need to construct the pdata based on the DT information for runtime use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Access the pdata via a pointer within the twl4030_priv structure.
In preparation for DeviceTree support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allocate the private data with devm_kzalloc.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We no longer have users for the set_hs_extmute callback which has been
replaced by hs_extmute_gpio so the codec driver can handle the external
mute if it is needed by the board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The external mute (if it is in use) is handled by a GPIO line. Prepare to
remove the set_hs_extmute callback and replace it with:
hs_extmute_gpio: the GPIO number to use for external mute
When the users of set_hs_extmute has been converted the callback can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use DAPM mapping for stream events and give unique names for the streams.
This change also fixes the following warning:
twl6040-codec twl6040-codec: Failed to create Capture debugfs file
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use DAPM mapping for stream events and give unique names for the streams.
This change also fixes the following warning:
twl4030-codec twl4030-codec: Failed to create Capture debugfs file
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'dres' field (discharge resistance for headphone outputs) is no longer
used in the driver, so remove it.
It was used in the original version of the driver when entering standby
from off, but we stopped using it when we switched from having a single
startup sequence to having separate cap and capless sequences.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We continue to allow the AB8500 CODEC to be registered via the AB8500
Multi Functional Device API, only this time we extract its configuration
from the Device Tree binary.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is more idiomatic as it means we verify that the device is there
prior to trying to do the card probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the LRCLK is shared and the WM8960 is clock master then we should
enable the LRCM bit to tell the device that it should drive LRCLK when
either ADC or DAC is enabled rather than separately driving the two
LRCLKs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For ENUM controls the bitmask is calculated based on the number of items.
Currently this is done each time the control is accessed. And while the
performance impact of this should be negligible we can easily do better. The
roundup_pow_of_two macro performs the same calculation which is currently done
manually, but it is also possible to use this macro with compile time constants
and so it can be used to initialize static data. So we can use it to initialize
the mask field of a ENUM control during its declaration.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
PowerPC ASoC drivers frequently use the _BE variants of the SNDRV_PCM_FORMAT
macros, so we need to look for those as well.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A bigger set of updates than I'm entirely comfortable with - things
backed up a bit due to travel. As ever the majority of these are small,
focused updates for specific drivers though there are a couple of core
changes. There's been good exposure in -next.
The AT91 patch fixes a build break.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=o1sd
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for 3.6
A bigger set of updates than I'm entirely comfortable with - things
backed up a bit due to travel. As ever the majority of these are small,
focused updates for specific drivers though there are a couple of core
changes. There's been good exposure in -next.
The AT91 patch fixes a build break.
This is better style as we acquire resources we will need before we go into
the ASoC card probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Better style as we get all the resources we need prior to starting the
ASoC level probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 98d3088e5 (SoC: core: Fix check before defaulting to regmap)
, it is not necessary to provide codec->control_data anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 98d3088e5 (SoC: core: Fix check before defaulting to regmap)
, it is not necessary to provide codec->control_data anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 98d3088e5 (SoC: core: Fix check before defaulting to regmap)
, it is not necessary to provide codec->control_data anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is better style since it has us obtaining all resources before we
try the ASoC probe. This change also fixes a potential issue where we
don't enable the regulators before trying to confirm the device ID which
could cause a failure during probe in some system configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Timur Tabi <timur@freescale.com>
The core_intercon is added two times, remove the redundant one
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Long term all drivers should be using regmap directly. This is more
idiomatic and moves us towards the removal of the ASoC level cache
code.
The initialiasation of reserved register bits in probe() is slightly odd
as the defaults being written don't appear to match the silicon defaults
but the new code should have the same effect as the old code.
The watchdog code will now unconditionally do a mute and unmute when
resyncing but since we only sync when we are very sure there is something
to sync this should have no impact.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Johannes Stezenbach <js@sig21.net>
This is better style as it ensures we don't try to do the ASoC probe
without required resources. Also convert to devm_ while we're at it,
saving a bit of code, and fix a leak of enable on error.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Johannes Stezenbach <js@sig21.net>
Ensure that we have confirmed that we've got the device in place before
we register with ASoC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is better style since we acquire all needed resources before we try
to do the ASoC card probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will be used to enable additional control of the regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This uses already defined name of registers and makes code more readable.
Signed-off-by: Gaëtan Carlier <gcembed@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Playing a mono track on a mc13783 codec results in incorrect playback rate.
Remove mono support so that a mono track can be played correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Gaëtan Carlier <gcembed@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix warning by using format specifier %zu for type size_t
Sparse warning:
sound/soc/codecs/wm0010.c:411:2: warning:
format ‘%d’ expects argument of type ‘int’,
but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're holding the wm0010->lock mutex when we goto err_core.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Device tree support for tlv320aic3x CODEC driver.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is more idimatic for modern drivers. Also fix a couple of return
codes while we're at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Doesn't make any practical difference given that _SUSPEND and _OFF are
equivalent for the driver but it's what we're really doing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make it easier to integrate the management of the clock supplying the
WM0010 with DAPM by providing a dummy supply widget which supplies the
interface widgets, this can be connected to clock outputs by the machines.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With appropriate clocking configuration the WM0010 driver supports 44.1kHz
audio; enable that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM0010 is a compact digital signal processor that has been
highly optimised for low-power audio applications. Extensive memory
resources and core optimisation allow the device to manage all audio
processing algorithms efficiently and autonomously, while the host
processor sleeps or performs other tasks.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are some new WM1811 variants distinguished by both revision and
cust_id which need slightly different handling.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes the analogue circuitry connected to the microphone needs some
time to settle after power up. Allow systems to configure this delay in
the platform data, the driver will then insert the required delay during
power up of paths that involve the microphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
The capture volume increases with the register value so it shouldn't be
flagged as inverted.
Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the microphone input source is not selectable as while there is
a DAPM widget it's not connected to anything so it won't be properly
instantiated. Add something more correct for the input structure to get
things going, even though it's not hooked into the rest of the routing
map and so won't actually achieve anything except allowing the relevant
register bits to be written.
Reported-by: Christop Fritz <chf.fritz@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
If DRC coefficients are not configured via platform data then add bytes
controls for them instead so they can be configured by applications. This
is the normal means of controlling things like this for newer systems, we
maintain compatibility with platform data to avoid disruption to existing
systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Arizona devices support two output system clocks. Provide support for
configuring these via set_sysclk(). Once the clock API is more useful
we should migrate over to that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core will bring the bias level up for us since we use idle_bias_off,
duplicating this may be harmful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
slab.h header file was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the process of moving over from static board files to the device
tree, reset pins of peripheral reset pins should be handled by their
corresponding drivers.
Add a reset-gpio DT property to the cs4270 driver, and de-assert it
before probing the chip. The logic could be augmented some day to
re-assert it when codec is put to suspend.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's never any need to cast away from void.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
It's currently only used in one place but another user will be added
shortly and there's an argument it's clearer anyway.
Also add support for readback in mode 1, though it's not currently used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since jackdet only reports deltas it won't generate an interrupt on startup
when a jack is not present. This doesn't make a difference to userspace
but does mean we don't generate a notification via the internal notifier
chains. Fix that by scheduling a work to poll the chip after the clock is
enabled. Use an extremely large timeout since there's no urgency and we
don't want to report a false negative.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The FLLs in the WM8994 series devices can be started without any reference
being supplied, mainly for use in analogue bypass cases. Implement support
for this mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
version.h header file inclusion is no longer needed for this file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A few updates for issues discovered during the merge window, the main
one being the fix for the issues with defaulting to use of regmap
without properly checking if there was I/O in place already.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pxAa
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-3.6
ASoC: Additional updates for 3.6
A few updates for issues discovered during the merge window, the main
one being the fix for the issues with defaulting to use of regmap
without properly checking if there was I/O in place already.
A bunch of small fixes for ASoC, mainly against regressions due to the
defaulting regmap i/o, in addition to a HD-audio fixup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=XuSA
-----END PGP SIGNATURE-----
Merge tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bunch of small fixes for ASoC, mainly against regressions due to the
defaulting regmap i/o, in addition to a HD-audio fixup."
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: core: Fix check before defaulting to regmap
ALSA: hda - Support dock on Lenovo Thinkpad T530 with ALC269VC
ASoC: wm8962: Allow VMID time to fully ramp
ASoC: AC97 doesn't use regmap by default
ASoC: sgtl5000: enable VAG_POWER for LINE_IN
ASoC: ab8500: Inform SoC Core that we have our own I/O arrangements
ASoC: omap: Add missing modules aliases to get sound working on omap devices
sound: tegra_alc5632: Adjust to of_get_named_gpio() change
sound: tegra_wm8903: Adjust to of_get_named_gpio() change
ASoC: mc13783: Provide codec->control_data
ASoC: ux500: Include the correct header files
ASoC: wm8994: Hold runtime PM reference while handling mic and jack IRQs
ASoC: sgtl5000: remove unneeded snd_soc_dapm_new_widgets in probe
ASoC: mxs-saif: set a base clock rate for EXTMASTER mode work
ASoC: mxs-saif: fix clock prepare and enable unbalance issue
ASoC: wm8994: Ensure there are enough BCLKs for four channels
Since commit 38cbf9598f
("ASoC: core: Try to use regmap if the driver doesn't set up any I/O")
any ASoC codec which doesn't set codec::control_data is assumed
to use regmap. That doesn't work with AC97 so this workaround
sets the codec::control_data member to a random value to restore
proper behaviour.
Tested with WM9712.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
LINE_IN also needs VAG_POWER on or we may hear noise when directly
route LINE_IN to Headphone Mux.
Tested on imx28evk.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If codec->control_data is not populated SoC Core assumes we want to
use regmap, which fails catastrophically, as we don't have one:
Unable to handle kernel NULL pointer dereference at virtual address 00000080
pgd = c0004000
[00000080] *pgd=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 Not tainted (3.5.0-rc6-00884-g0b2419e-dirty #130)
PC is at regmap_read+0x10/0x5c
LR is at hw_read+0x80/0x90
pc : [<c01a91b8>] lr : [<c0216804>] psr: 60000013
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c28c
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac96: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
If codec->control_data is not provided, the following crash happens:
Unable to handle kernel NULL pointer dereference at virtual address 00000078
pgd = 80004000
[00000078] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 Tainted: G W (3.5.0-next-20120725+ #1263)
PC is at regmap_read+0x18/0x64
LR is at hw_read+0x50/0x98
pc : [<802bcd90>] lr : [<803cad18>] psr: 60000013
...
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
twl6040 ES1.1 and ES1.2 have the same revid (0x01).
ES1.3 of twl6040 REVID is 0x02.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensures that we don't interact badly with the power management framework,
especially in the cases where we're doing deferred work or we're using a
direct GPIO for these signals.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's a driver bug that sgtl5000 dapm widget kcontrols do not work.
e.g. can not select capture mux with amixer tool(no error info prompted).
The root cause is that we still call snd_soc_dapm_new_widgets in
codec driver probe function afer converting to table based widgets.
This will cause the card dapm widgets are instantiated before the
dapm_routes are registered.
Then, no available dapm widget pathes can be found during instantiation
which finally will cause soc_dapm_mux_update_power to fail(can not find
correct path with kcontrol) in snd_soc_dapm_put_enum_double function.
Here we remove the unneeded snd_soc_dapm_new_widgets in codec probe
and let the soc core to handle the register sequence properly.
Then we can fix above issue.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise if someone tries to use all four channels on AIF1 with the
device in master mode we won't be able to clock out all the data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
This has been a pretty quiet release - very little activity in framework
terms, mostly just a few new drivers and updates:
- Added the ability to add and remove DAPM paths dynamically, mostly for
reparenting on clock changes.
- New machine drivers for Marvell Brownstone, ST-Ericsson Ux500
reference platform and ttc-dkp.
- New CPU drivers for Blackfin BF6xx SPORTs in I2S mode, Marvell MMP,
Synopsis Designware I2S controllers, and SPEAr DMA and S/PDIF
- New CODEC drivers for Dialog DA732x, ST STA529, ST-Ericsson AB8500, TI
Isabelle and Wolfson Microelectronics WM5102 and WM5110
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JHE2
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for 3.6
This has been a pretty quiet release - very little activity in framework
terms, mostly just a few new drivers and updates:
- Added the ability to add and remove DAPM paths dynamically, mostly for
reparenting on clock changes.
- New machine drivers for Marvell Brownstone, ST-Ericsson Ux500
reference platform and ttc-dkp.
- New CPU drivers for Blackfin BF6xx SPORTs in I2S mode, Marvell MMP,
Synopsis Designware I2S controllers, and SPEAr DMA and S/PDIF
- New CODEC drivers for Dialog DA732x, ST STA529, ST-Ericsson AB8500, TI
Isabelle and Wolfson Microelectronics WM5102 and WM5110
The conversion of the core driver to irqdomains means that we don't need
and irq_base to have working interrupts so use wm8994_request_irq() to
deal with looking up the interrupt number for the micdet IRQ.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure robust startup of the part by going through the reset procedure
prior to resyncing the full register cache, avoiding potential intermittent
faults in some designs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The WM5110 is a highly integrated low power audio subsystem for
smartphones, tablets and other portable audio devices. It combines
an advanced DSP feature set with a flexible, high performance audio
hub CODEC.
This patch adds the audio CODEC driver for the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
GCC complains that "ret" is uninitialized here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-By: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some Arizona chips have a higher frequency for the FLL VCO, support this
in the common code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds input selection of main codec clock - from what pin.
Both registers set same value since codec uses clock divider or pll at one time.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds AGC target level and times settings for TLV320AIC3x.
Enums uses small arrays of two channels left and right since it uses different registers.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds missing deemphasis switch.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The analogue PGA shifts were used; this makes no practical difference as
the values are the same.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix spelling mistake in "High-Performance" option of twl6040 power mode.
Signed-off-by: Simon Wilson <simonwilson@google.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If an audio interface is configured to use ASYNCCLK then update the
asynchronous sample rate rather than one of our primary sample rates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow any BCLK which can be divided down to generate LRCLK, not just the
lowest possible BCLK to clock out the samples.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the user to select which of the system clocks each AIF is referenced
to and constran the DAI to the set of frequencies which can be generated
from that clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They're the rates for the BCLK, not for the sample rate, so rename so that
we don't confuse ourselves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The STA529 is a digital stereo class-D audio amplifier. It includes an
audio DSP, an ST proprietary high-efficiency class-D driver and CMOS
power output stage. It is intended for high-efficiency
digital-to-power-audio conversion for portable applications.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds missing register default values to cache.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds register and bit shift definitions in header file.
Changes are for TLV320AIC310x based on data sheet.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Leave it up to the machine driver to disable accessory detection if
desired, the common pattern is to have accessory detection be a wake
source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In sound/soc/codecs/tlv320aic3x.c
data = snd_soc_read(codec, AIC3X_PLL_PROGA_REG);
snd_soc_write(codec, AIC3X_PLL_PROGA_REG,
data | (pll_p << PLLP_SHIFT));
In the above code, pll-p value is OR'ed with previous value without
clearing it. Bug is not seen if pll-p value doesn't change across
Sampling frequency.
However on some platforms (like AM335x EVM-SK), pll-p may have different
values across different sampling frequencies. In such case, above code
configures the pll with a wrong value.
Because of this bug, when a audio stream is played with pll value
different from previous stream, audio is heard as differently(like its
stretched).
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Without this very high BCLKs will be configured incorrectly.
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Otherwise we fail to link when building as modules due to multiple
init/exit functions.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the support for spdif in audio codec.
Signed-off-by: vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It seems that the code duplication was added at a merge operation.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This gets the registers set up as early as possible, mainly useful for the
GPIOs to ensure that they're in the correct mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is only one caller and this allows us to cleanly leave the CODEC
with the internal LDO powered down which is the default state we're
looking for and means that we can robustly disable the register cache
only when we either disable the LDO or power down the external
regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get it done as early as possible, it's neater and minimises the time the
pins aren't configured as requested.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even though the WM8904 is able to use idle_bias_off during both probe
and resume we were needlessly leaving the device in standby mode. Instead
power the device down as soon as we've confirmed that we can talk to it
and don't manage the bias level at all over suspend and resume, the core
will take us down to our minimum power level.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into for-3.6
Linux 3.5-rc4 contains some bug fixes which overlap with new features.
The WM5102 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices based on the Arizona platform.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Wolfson Arizona series of audio hub CODECs can share a large amount
of their driver code as the result of a common register map. This patch
adds some of this core support, providing a basis for the initial WM5102
audio driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is a missing mutex_unlock() here. The cleanup path also has more
debug output.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes a leak if snd_soc_register_codec fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
GPLv2 -> GPL v2
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also convert to use update_bits() while we're at it. No great need to do
this, it's just a bit neater to do as much as possible in the I2C probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
There's no reason to defer requesting of the interrupt until the CODEC
probe and doing so results in more work if we hit an error as we'll have
registered the CODEC with the core. It's neater to acquire as many of the
resources we'll need as we can in the bus probe function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
There's no urgent need for the interrupt handler to use the ASoC I/O
functions and it'll support a further move in where we request the
interrupt so call the regmap APIs directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Ensure that the device pins are configured as soon as possible by moving
the pin configration (including MICBIAS) into the I2C probe() function.
This had been done in the CODEC probe() function when we were relying on
the ASoC register I/O code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
This patch adds support for Dialog DA732x audio codecs.
Signed-off-by: Michal Hajduk <Michal.Hajduk@diasemi.com>
Signed-off-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They aren't marked as readable and the feature is never used so they'll
never get referenced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we don't have control over the LDO but do have control over the other
regulators then we may end up trying to write to a powered off device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're using demv_regulator_bulk_get() so don't need to manually free and
this is in the CODEC driver not the I2C driver anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add codec-driver for ST-Ericsson AB8500 mixed-signal ASIC.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should be using the regmap API consistently for all the cache only
configuration and we should be going cache only before we power down
the supplies.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We no longer have a flat ASoC cache so can't peer directly into the array
any more but should instead use the register I/O functions to update the
cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org (v3.4)
Rather than having varying timeouts depending on the transition always
use a 4s timeout. This provides better diagnostics for clocking errors
and ensures compatibility with current calibration firmwares.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should set "isabelle_regmap" before using it. GCC complains.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Volume updates may not be acted upon if there is no clock applied when
the volume update is written. Ensure this doesn't happen by writing out
registers with volume updates after we enable each of the clocks.
There are more registers updated than before as previously we were
relying on wm_hubs to set those for controls it manages.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Ensure that all the actions get taken at appropriate times by calling the
_PRE and _POST events for the aifNclk_ev functions explicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The core fills in some blanks which makes it annoying to do the right thing
and constify the calls in the core.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With devm_ APIs regmap_exit() not needed, so remove regmap_exit().
Signed-off-by: Vishwas A Deshpande <vishwas.a.deshpande@ti.com>
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: Support TI Isabelle Audio driver
The Isabelle Audio IC is a complete low power high fidelity CODEC with integrated
ADCs, DACs, decimation and interpolation filters, PLL, and power providers. This
device supports 2 analog and 2 digital microphone channels, a mono earpiece driver,
stereo class G headphone drivers with ultra low power and best SNR in the industry,
stereo Class D speaker drivers, and 2 high performance Line drivers.
The below patch is a basic driver code for TI Isabelle audio codec. The
functionalities like headset detection, etc., will be included incrementally
in the up-coming patches.
Signed-off-by: Vishwas A Deshpande <vishwas.a.deshpande@ti.com>
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
version.h header file is no longer required.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
version.h header file is no longer needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALSA mixers cannot classify this "Class-D Amplifier Gain" speaker output
gain control as a playback control. Fix this by changing the name as
"Class-D Playback Volume".
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows the GPIOs to be available as soon as the I2C device has
probed, which in turn enables machine drivers to request the GPIOs in
their probe(), rather than deferring this to their ASoC machine init
function, i.e. after the whole sound card has been constructed, and
hence the WM8903 codec is available.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten
for the better support of "implicit feedback". If anything about USB
got broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up immediately
at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital links
between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid the accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal routing
through components with tight sequencing and formatting constraints
within their internal paths or where there are multiple components
connected with CPU managed DMA controllers inside the SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like digital
basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124, Texas
Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be
sent slightly later as partly depending on the changes of DRM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJPvD/9AAoJEGwxgFQ9KSmkPsIP/AuBGpAZy7b7FiEEIy1Hhdws
US8WVuPzyDslMVdzZ8OFqyPXanIcL9gscoOGMZOEy7UFtMBiR4GuYiPRPubEMxuP
/gopUqK4SqIsIwT238qqYszSJSxE7gNEZ/2jhSGtkX4EkaSZ4bAskn0iOKX5uw2f
kTUQknA1rNLIGba2z6rJbgIW7hdxGfpFy05ruv3ct81nO+5JlgyLuP/v5R6jL+do
cum0N4dJFRd9YSEi2BG612gdz8LJyzOgPqBKmxMEva6BfqLkR8EdP80FtE3eEOiP
Et1q2LhZwOlBt0BEjsjjOVxMsgxVax6ps9cuNRTk5ECEOldU5dbDatC45L/e9mSD
OQVUjYAX1mQAtYva4U4PPn6WU6ma2L5yjy4peCObtyCMkEchXk1bfs4CEfVqCXUP
yFYN8C+y6osZOyWE3+Enn9ifZdWyLeSVq6CT33Yt+fyKlswp6gRkhKYiEPqTA5aU
p71X59Pp7q1y3tQwiMJNpf2QdkxuxfKURHswdc4BS9ct0mdZhQX0GyDS7OffkTd4
Lq5UkVMHA1rLlF9oRPd2C9P4BuMEuvLjf662YCKiw+mWFYdBC036DHLLjm1Hcwuj
UkpQ2PSrrdHG1u0c3ooZ9dQj1BNX4LoABLqvaMtce6sESD/hJ5gcprYJWvtituwM
ZzZiJavIWsoJ+SWQWBHe
=+JSm
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten for
the better support of "implicit feedback". If anything about USB got
broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up
immediately at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital
links between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal
routing through components with tight sequencing and formatting
constraints within their internal paths or where there are multiple
components connected with CPU managed DMA controllers inside the
SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like
digital basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124,
Texas Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be sent
slightly later as partly depending on the changes of DRM."
Fix up conflicts in regmap (due to duplicate patches, with some further
updates then having already come in from the regmap tree). Also some
fairly trivial context conflicts in the imx and mcx soc drivers.
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (280 commits)
ALSA: snd-usb: fix stream info output in /proc
ALSA: pcm - Add proper state checks to snd_pcm_drain()
ALSA: sh: Fix up namespace collision in sh_dac_audio.
ALSA: hda/realtek - Fix unused variable compile warning
ASoC: sh: fsi: enable chip specific data transfer mode
ASoC: sh: fsi: call fsi_hw_startup/shutdown from fsi_dai_trigger()
ASoC: sh: fsi: use same format for IN/OUT
ASoC: sh: fsi: add fsi_version() and removed meaningless version check
ASoC: sh: fsi: use register field macro name on IN/OUT_DMAC
ASoC: tegra: Add machine driver for WM8753 codec
ALSA: hda - Fix possible races of accesses to connection list array
ASoC: OMAP: HDMI: Introduce codec
ARM: mx31_3ds: Add sound support
ASoC: imx-mc13783 cleanup
mx31moboard: Add sound support
ASoC: mc13783 codec cleanups
ASoC: add imx-mc13783 sound support
ASoC: Add mc13783 codec
mfd: mc13xxx: add codec platform data
ASoC: don't flip master of DT-instantiated DAI links
...
These are all new code, they've been in -next already so should be OK
for merge this time round. I'd been planning to send a pull request
today after they'd had a bit of exposure there to make sure breakage
didn't propagate into your tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5L34
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Last minute updates
These are all new code, they've been in -next already so should be OK
for merge this time round. I'd been planning to send a pull request
today after they'd had a bit of exposure there to make sure breakage
didn't propagate into your tree.
The major thing here is the addition of some helpers to factor code out
of drivers, making a fair proportion of regulators much more just data
rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI TPS65913,
TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring caused
so many conflicts that eventually topic branches were abandoned for this
release.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UR7s
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The major thing here is the addition of some helpers to factor code
out of drivers, making a fair proportion of regulators much more just
data rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI
TPS65913, TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring
caused so many conflicts that eventually topic branches were abandoned
for this release."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (227 commits)
regulator: tps65910: use of_node of matched regulator being register
regulator: tps65910: dt: support when "regulators" node found
regulator: tps65910: add error message in case of failure
regulator: tps62360: dt: initialize of_node param for regulator register.
regulator: tps65910: use devm_* for memory allocation
regulator: tps65910: use small letter for regulator names
mfd: tpx6586x: Depend on regulator
regulator: regulator for Palmas Kconfig
regulator: regulator driver for Palmas series chips
regulator: Enable Device Tree for the db8500-prcmu regulator driver
regulator: db8500-prcmu: Separate regulator registration from probe
regulator: ab3100: Use regulator_map_voltage_iterate()
regulator: tps65217: Convert to set_voltage_sel and map_voltage
regulator: Enable the ab8500 for Device Tree
regulator: ab8500: Split up probe() into manageable pieces
regulator: max8925: Remove check_range function and max_uV from struct rc5t583_regulator_info
regulator: max8649: Remove unused check_range() function
regulator: rc5t583: Remove max_uV from struct rc5t583_regulator_info
regulator: da9052: Convert to set_voltage_sel and map_voltage
regulator: max8952: Use devm_kzalloc
...
Introduce codec for HDMI. At the moment, this is a dummy codec. In the
future it will parse the EDID to modify the supported parameters, such
as the number of channels and the sample rates. At the moment, it blindly
supports all the sample rates and audio channels described in the HDMI
1.4a specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A few last-minute regression fixes for 3.4 final kernel.
All trivial, and Cc'ed to stable kernel.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=e/ZS
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few last-minute regression fixes for 3.4 final kernel. All trivial,
and Cc'ed to stable kernel."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Fix AIF2ADC power down
ALSA: hda/idt - Fix power-map for speaker-pins with some HP laptops
ASoC: cs42l73: Sync digital mixer kcontrols to allow for 0dB
aic3x_set_headset_detection() isn't made available outside the driver or
referenced within the driver which sparse notices and complains about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for irq_domain support change the code to the not switch
based on the irq number. This actually makes things simpler, if slightly
repetitive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the devm_ versions of the regmap and memory allocation functions,
saving some error handling code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some of the Digital mixer kcontrol max values were off by 1 not allowing a max of 0dB.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Makes sparse happy and avoids polluting the global namespace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
We need to read the real register values
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're trying to remove all usage of the ASoc level cache and I/O code and
for a device like this with a pretty sparse register map the rbtree cache
is a better idea anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
None of the machines uses the gain ramp possibility for HS/HF.
This code path is mostly unused and it does not reduces the pop
noise on the output (it alters it to sound a bit different).
The preferred method to reduce pop noise is to use ABE.
Remove the gain ramp, and related features form the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As good as nothing exciting here; just a few trivial fixes for
various ASoC stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ZPkR
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound sound fixes from Takashi Iwai:
"As good as nothing exciting here; just a few trivial fixes for various
ASoC stuff."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: omap-pcm: Free dma buffers in case of error.
ASoC: s3c2412-i2s: Fix dai registration
ASoC: wm8350: Don't use locally allocated codec struct
ASoC: tlv312aic23: unbreak resume
ASoC: bf5xx-ssm2602: Set DAI format
ASoC: core: check of_property_count_strings failure
ASoC: dt: sgtl5000.txt: Add description for 'reg' field
ASoC: wm_hubs: Make sure we don't disable differential line outputs
This patch improves playback quality for few sample rates like 8000 and
11025 Hz.
This also fixes an issue observed during testing of pll slave mode. Due
to the issue, on some rare occasions there was no sound output for first
time playback after system boot, though all subsequent playbacks were
fine. It was mainly because of the sequence in which SRM bit was
enabled.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than invalidating the cached DCS value every time the headphone
gain changes store multiple values, indexed by gain. This allows the
optimisation we get from the cache to take effect more often.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is now very standard behaviour for CODECs so shouldn't be device
specific and we shouldn't really be trying to peer into the register
cache from atomic context anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the conversion to module_init_i2c() the original open coded module
exit function was left. Remove it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Cirrus Logic CS42L52 Low Power Stereo Codec
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core allocates the live copies, we shouldn't try to duplicate it and
were buggy trying to do so as we were using uninitialised data for the
control data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* commit f9dfbf9 "ASoC: tlv320aic23: convert to soc-cache" leads to
a bug preventing resumeof the codec as regmap expects a 9 bits data
register but 0xFFFF is passed in tlv320aic23_set_bias_level and this
values gets cached preventing any write to the TLV320AIC23_PWR
register as the final value produced by regmap is (register << 9) | value
* this patch solves the problem by only working on the 9 bits the
register contains.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Class W can be used for any path where only data from the DAC is routed
to the headphones. Currently we only enable it when the direct DAC to
headphone path is used but it can also be enabled for paths that go via
the output mixer providing the DAC is the only input to the output mixer.
Implement support for this, including updates to the class W status when
the output mixer configuration is changed. This also allows us to enable
the DC servo optimisations for DAC to headphone paths where the output
mixer is used.
In general the direct DAC path is still preferred as this will offer
better performance on most wm_hubs devices but these additional paths
can simplify use case management.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the analogue portions of the checks for class W are the same over
all the devices factor out these checks into wm_hubs and while we're at
it also use wm_hubs_dac_hp_direct() to enable class W optimisations on
more paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The optimisations which we can do with caching the headphone DCS result in
wm_hubs have only been enabled in cases where class W is enabled. However,
there are more use cases which can benefit from the cache, especially with
WM8994 series devices with their more advanced digital routing.
Rather than keying off the class W information from the CODECs have a
check in wm_hubs for a suitable path and use that to determine if we can
deploy our headphone optimisations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a bug discovered during testing of non pll slave mode.
Due to the bug chip was not getting correctly configured and as a result
there was no sound output while playback. After applying this patch,
both pll and non pll modes work fine.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A workaround for an ASUS laptop and a few ASoC changes;
most of the commits are tagged for stable, too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=KjOE
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A workaround for an ASUS laptop and a few ASoC changes; most of the
commits are tagged for stable, too."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Improve sequencing of AIF channel enables
ALSA: HDA: Add external mic quirk for Asus Zenbook UX31E
ASoC: fsi: update for dmaengine prep_slave_sg fallout.
ASoC: core: Fix card RTD count for deferred probe.
ASoC: cs42l73: don't use negative array index
ASoC: dapm: Ensure power gets managed for line widgets
If a driver using a custom mic detection callback has provided a table
of mic detection rates via platform data then use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use a slightly larger debounce when identifying accessory type and a
slightly smaller one when detecting buttons in response to user feedback
from large scale testing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we're not actively doing audio we don't need the microphone biases
to be regulated, noise is not important when we are not looking at the
audio signal. Save some power by putting the MICBIAS regulators into
bypass mode when not doing audio.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mostly a one to one converion. On one occasion the patch replaces a
snd_soc_read-snd_soc_write sequence with regmap_update_bits though as it helps
to keep the conversion simple.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have never really updated that version number and probably never will, so
just remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not all advertised rates are available for all sysclk frequencies. Add
additional sysclk based rate constraints.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
