If FLL bypass is left enabled when we disable the CODEC then the output
clock will be left running which consumes a small amount of additional
current. Only enable bypass when there is an output.
Signed-off-by: Kyung-Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While we need to clean up unused single ended line outputs we don't want
to do this if the outputs are in differential mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While reading through sound/soc/codecs/wm8994.c I noticed a fair
amount of trailing whitespace. This patch gets rid of it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This ensures a clean startup of the channels, without this change some
use cases could result in issues in a small proportion of cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The Springbank module can support a range of sample rates, selected at
runtime via GPIO configuration. Allow these to be configured at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since AIF3 shares clock signals with other audio interfaces in order to
ensure it doesn't drive undesirable clocks we need to tristate it. Rather
than forcing the machine driver to do so have the driver do this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch converts multiple if conditions in to single if with "&&"s.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current DA7210 driver does support PLL mode fully. It uses fixed
value of input master clock and PLL mode is enabled and disabled based
on the sampling frequency being used for playback or recording. It also
doesn't support Sample Rate Measurement feature of DA7210 hardware.
This patch adds full support for PLL and SRM. Basically following three
modes of operation are possible for DA7210 hardware,
(1) I2S SLAVE mode with PLL bypassed
(2) I2S SLAVE mode with PLL enabled
(3) I2S Master mode with PLL enabled
This patch adds support for all three modes. Also, in case of SLAVE mode
with PLL, it supports SRM (Sample Rate Measurement) feature of the chip.
Actually this patch was submitted earlier and received some review
comments, but after that the driver got update by other patches. Because
of that, I am considering this as new patch and not versioning it based
of previous patches. This version tries to take care of all review
comments received for earlier submissions.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEbBAABAgAGBQJPi3XOAAoJEHm+PkMAQRiGnsUH9RjHwH4YFVyuP/DKtKa6zs74
wqkpT15yITQ5WWMog4JaJFFg5rJCUd8QZr7AS/HSn0ijDyZX5VU7Rcs9cMudDzNR
H/5K/AscS4fjb0HwWVqoltTWHRb9QGSwVN3+E3VCDLt9P89YJ0o3QztkkuEX5dkZ
jc7reVXTfRnCcILEa9jleOzrn+OLM3j/jAjQ2hGunl8EDLzD4b17HHPoli4jEZ/5
5ibpSVsPD+AqzN+glbXvYjVItl12D0IQos/JdOwfuZriCVWLxysSSwHZTbPCyvBZ
LHH4HR5T+XLSXbjJeNkUFHLzqU+d5gVRadIoWtJCxqxFjKbOs2YtzJ5Ai0nDiw==
=kTkC
-----END PGP SIGNATURE-----
ASoC: Merge tag 'v3.4-rc3' into for-3.5
Linux 3.4-rc3 contains a bunch of Tegra changes which are conflicting
annoyingly with the new development that's going on for Tegra so merge
it up to resolve those conflicts.
Conflicts:
sound/soc/soc-core.c
sound/soc/tegra/tegra_i2s.c
sound/soc/tegra/tegra_spdif.c
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If cs42l73_get_mclkx_coeff() returns < 0 (which it can) in
sound/soc/codecs/cs42l73.c::cs42l73_set_mclk(), then we'll be using
the (negative) return value as array index on the very next line of
code - that's bad.
Catch the negative return value and propagate it to the caller (which
checks for it) and things are a bit more sane :-)
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sound/soc/codecs/wm9705.c: In function 'ac97_prepare':
sound/soc/codecs/wm9705.c:251: error: 'runtime' undeclared (first use in this function)
This was caused by commit e6968a (ASoC: codecs: Remove rtd->codec usage from CODEC drivers),
which removed the 'struct snd_pcm_runtime *runtime = substream->runtime' definition.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the following build error:
sound/soc/codecs/ac97.c: In function 'ac97_prepare':
sound/soc/codecs/ac97.c:33: error: 'runtime' undeclared (first use in this function)
This was caused by commit e6968a (ASoC: codecs: Remove rtd->codec usage from CODEC drivers),
which removed the 'struct snd_pcm_runtime *runtime = substream->runtime' definition.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the following build error:
sound/soc/codecs/wm9712.c:482:32: error: 'runtime' undeclared (first use in this function)
sound/soc/codecs/wm9712.c:499:33: error: 'runtime' undeclared (first use in this function)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Later WM8994 class devices can bypass the FLL from BCLK. Do this
automatically when the FLL input and output frequencies match up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
release_firmware() does its own NULL ptr testing, it's redundant to
also test before calling it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than adding new arguments to regulator_register() every time we
want to add a new bit of dynamic information at runtime change the function
to take these via a struct. By doing this we avoid needing to do further
changes like the recent addition of device tree support which required each
regulator driver to be updated to take an additional parameter.
The regulator_desc which should (mostly) be static data is still passed
separately as most drivers are able to configure this statically at build
time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sound/soc/codecs/lm49453.c: In function 'lm49453_set_dai_fmt':
sound/soc/codecs/lm49453.c:1189:4: warning: overflow in implicit
constant conversion [-Woverflow]
sound/soc/codecs/lm49453.c:1193:4: warning: overflow in implicit
constant conversion [-Woverflow]
sound/soc/codecs/lm49453.c:1197:4: warning: overflow in implicit
constant conversion [-Woverflow]
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ak4642 out_tlv is +12.0dB to -115.0 dB, and it supports mute.
But current settings didn't care +1 step for mute.
This patch adds it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
In order to support CODEC<->CODEC links remove the assumption that there
is only a single CODEC on a DAI link by removing the use of the CODEC
pointer in the rtd from the CODEC drivers. They are already being passed
their DAI whenever they are passed an rtd and can get the CODEC from
there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the following warning during kernel boot:
0-000a: 850 <--> 1600 mV at 1200 mV normal
0-000a: Voltage range but no REGULATOR_CHANGE_VOLTAGE
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some codecs namely Cirrus Logic Codecs have a way of wrapping the dB scale around 0dB without 0dB being in the middle.
Rework of SOC_DOUBLE_R_SX_TLV to be more consistent with other asoc tlv macros.
Add single register macro : SOC_SINGLE_SX_TLV.
Use snd_soc_info_volsw for .info
Use snd_soc_get_volsw_sx, snd_soc_put_volsw_sx for single and double.
kcontrols for CS42L51 and CS42L73 are adjusted to these new TLV Macros.
The max value is determined by: (number of steps) +1 for 0dB +max from codec datasheet.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As manual described, VAG is an internal voltage reference of DAC/ADC,
So enabled it before DAC/ADC up.
One more thing should care about is VAG fully ramped down requires 400ms,
wait it to avoid pop.
Signed-off-by: Zeng Zhaoming <zengzm.kernel@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sound/soc/codecs/max98095.c: In function 'max98095_jack_detect_enable':
sound/soc/codecs/max98095.c:2229:14: error: 'struct max98095_priv' has no member named 'jack_detect_delay'
sound/soc/codecs/max98095.c:2230:18: error: 'struct max98095_priv' has no member named 'jack_detect_delay'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This increases the chances we'll manage to hit a partially configured
state on restart and the power savings are extremely small.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for spi regmap feature to existing da7210
driver.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No current users and it's the last user of MICBIAS_E().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Zeng Zhaoming <zengzm.kernel@gmail.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Rather than trying to work around machine drivers which try to reprogram
the FLL while it is providing SYSCLK just return an error if they try.
This will avoid audio glitches during FLL reconfiguration, or at least
move the introduction of the glitches to the machine driver.
Since disabling the source for an active SYSCLK is not supported in the
first place systems shouldn't be doing this in the first place.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ML26124-01HB/ML26124-02GD is 16bit monaural audio CODEC which has high
resistance to voltage noise. On chip regulator realizes power supply rejection
ratio be over 90dB so more than 50dB is improved than ever. ML26124-01HB/
ML26124-02GD can deliver stable audio performance without being affected by noise
from the power supply circuit and peripheral components. The chip also includes
a composite video signal output, which can be applied to various portable device
requirements. The ML26124 is realized these functions into very small package
the size is only 2.56mm x 2.46mm therefore can be construct high quality sound
system easily.
ML26124-01HB is 25pin WCSP package; ML26124-02GD is 32pin WQFN package.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's possible that the regulator enable will fail and if it does we may
as well just give up with trying to bring the rest of the device up and
report the original error.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Timur Tabi <timur@freescale.com>
We can simply use the register cache code to synchronise the current
configuration down to the device when bringing up the DSP.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change adds the logic to support using the jack detect mechanism built
in to the codec to detect both when a jack was inserted and what type of
jack is present.
This change also supports the use of an external mechanism for headphone
detection. If this mechanism exists, when the max98095_jack_detect function
is called, the hp_jack is simply passed NULL.
This change supports both simple headphones, powered headphones, microphones
and headsets with both headphones and a mic.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM now has a DAPM-level lock which it manages itself so we don't need
to take the CODEC mutex to call DAPM any more. Also remove a redundant
call to snd_soc_dapm_sync(), jack reporting also triggers a DAPM sync.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's more idiomatic to do this and it means we don't try to bring up the
card if the CODEC didn't manage to bind successfully.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A collection of small fixes for 3.4-rc1, including
- mic-recording regression fix for Realtek codec
- clean-up of dmaengine parameter mess
- WM8894 calibration tweak
- minor fixes for asihpi and some bool module parms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=cW/4
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes for 3.4-rc1, including
- mic-recording regression fix for Realtek codec
- clean-up of dmaengine parameter mess
- WM8894 calibration tweak
- minor fixes for asihpi and some bool module parms"
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fix isa/opti9xx module param type
sound: fix oss/msnd_pinnacle module param type
ALSA: asihpi - fix return type of hpios_locked_mem_alloc()
ASoC: dmaengine_pcm: use dmaengine cyclic wrapper
ASoC: Add extra parameter to device_prep_dma_cyclic
ALSA: hda/realtek - Fix ADC assignment with a shared HP/Mic pin
ASoC: wm8994: Update WM8994 DCS calibration
The cleanup of the dmaengine parameter messup and a tweak to some
callibration values for WM1811.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XZ+C
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: A few more updates for 3.4
The cleanup of the dmaengine parameter messup and a tweak to some
callibration values for WM1811.
seeing a trickle of new features coming in they're getting much smaller
than they were. It's also nice to have some features which support
other subsystems building infrastructure on top of regmap. Highlights
include:
- Support for padding between the register and the value when
interacting with the device, sometimes needed for fast interfaces.
- Support for applying register updates to the device when restoring the
register state. This is intended to be used to apply updates supplied by
manufacturers for tuning the performance of the device (many of which
are to undocumented registers which aren't otherwise covered).
- Support for multi-register operations on cached registers.
- Support for syncing only part of the register cache.
- Stubs and parameter query functions intended to make it easier for other
subsystems to build infrastructure on top of the regmap API.
plus a few driver updates making use of the new features which it was
easier to merge via this tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Eo9
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Things are really quieting down with the regmap API, while we're still
seeing a trickle of new features coming in they're getting much
smaller than they were. It's also nice to have some features which
support other subsystems building infrastructure on top of regmap.
Highlights include:
- Support for padding between the register and the value when
interacting with the device, sometimes needed for fast interfaces.
- Support for applying register updates to the device when restoring
the register state. This is intended to be used to apply updates
supplied by manufacturers for tuning the performance of the device
(many of which are to undocumented registers which aren't otherwise
covered).
- Support for multi-register operations on cached registers.
- Support for syncing only part of the register cache.
- Stubs and parameter query functions intended to make it easier for
other subsystems to build infrastructure on top of the regmap API.
plus a few driver updates making use of the new features which it was
easier to merge via this tree."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (41 commits)
regmap: Fix future missing prototype of devres_alloc() and friends
regmap: Rejig struct declarations for stubbed API
regmap: Fix rbtree block base in sync
regcache: Make sure we sync register 0 in an rbtree cache
regmap: delete unused module.h from drivers/base/regmap files
regmap: Add stub for regcache_sync_region()
mfd: Improve performance of later WM1811 revisions
regmap: Fix x86_64 breakage
regmap: Allow drivers to sync only part of the register cache
regmap: Supply ranges to the sync operations
regmap: Add tracepoints for cache only and cache bypass
regmap: Mark the cache as clean after a successful sync
regmap: Remove default cache sync implementation
regmap: Skip hardware defaults for LZO caches
regmap: Expose the driver name in debugfs
mfd: wm8400: Convert to devm_regmap_init_i2c()
mfd: wm831x: Convert to devm_regmap_init()
mfd: wm8994: Convert to devm_regmap_init()
mfd/ASoC: Convert WM8994 driver to use regmap patches
mfd: Add __devinit and __devexit annotations in wm8994
...
There's a couple of small features here that were added late on but have
been in -next in my tree and some bug fixes. The wm_hubs stuff is
actually bug fixes - the stuff that's currently in 3.4 is a half way
house between the two solutions that the latest change allows the
machine to select between.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K2Tm
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
Last minute ASoC updates for 3.4
There's a couple of small features here that were added late on but have
been in -next in my tree and some bug fixes. The wm_hubs stuff is
actually bug fixes - the stuff that's currently in 3.4 is a half way
house between the two solutions that the latest change allows the
machine to select between.
The optimal management of VMID depends on a number of factors which vary
dynamically at runtime, for example the connection to a system docking
station. In some circumstances it is desirable to keep VMID enabled all
the time, in others it is desirable to aggressively power it up and down.
Provide a callback allowing machine driver to configure either the normal
power up/down mode (WM8994_VMID_MODE_NORMAL) or to maintain VMID even
when idle (WM8994_VMID_MODE_FORCE). This callback, wm8994_vmid_mode(),
should be called with the CODEC lock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8996 specification has been updated to specify 44.1kHz as a supported
sample rate. Update the driver to accept this configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently we can the accdet mutex from within DAPM when updating the device
state which means we take accdet then the CODEC mutex but we also do the
locking the other way around when responding to the jackdet IRQ. Move all
the jackdet use of the CODEC mutex out of the accdet lock to avoid this.
Since all the DAPM interactions depend only on a single threaded IRQ this
is still serialised.
The locking improvements in 3.5 allow a better solution there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch removes following registers from reg map defaults,
- Registers which are currently not used by driver
- Non existing registers
- Volatile registers
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current DA7210 driver has I2C support using older register cache
methods. This patch updates it for latest regmap framework.
This has been tested on DA7210 EVB with Samsung SMDK6410 board.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
from arch/arm into sound/soc. There's also some general driver specific
tweaks and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0lYr
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
A few more ASoC updates, the main one is the move of the audmux driver
from arch/arm into sound/soc. There's also some general driver specific
tweaks and fixes.
commit 891271c "ASoC: Convert wm8804 to direct regmap API usage"
only converts wm8804_spi_probe to use regmap_init_spi.
This patch adds missing regmap_init_i2c in wm8804_i2c_probe.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we are out of system sleep always use audio mode for jack detection
in order to avoid potential performance issues handing off between modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FpJH
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
This has been a very active release for ASoC, as well as the usual raft
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
Without that fix the wm8753 SPI initialization fails, and then produces
a kernel panic during boot with the following call trace:
Unable to handle kernel paging request at virtual address 37386d9b
[<c01ccafc>] (regmap_get_val_bytes+0x0/0x14) from [<c0243dfc>] (snd_soc_codec_set_cache_io+0x9c/0xcc)
[<c0243dfc>] (snd_soc_codec_set_cache_io+0x9c/0xcc) from [<c0244a4c>] (wm8753_probe+0x5c/0x1c4)
[<c0244a4c>] (wm8753_probe+0x5c/0x1c4) from [<c023bb24>] (soc_probe_codec+0x174/0x284)
[<c023bb24>] (soc_probe_codec+0x174/0x284) from [<c023c2c0>] (snd_soc_instantiate_cards+0x68c/0xe28)
[<c023c2c0>] (snd_soc_instantiate_cards+0x68c/0xe28) from [<c023d278>] (snd_soc_register_card+0x240/0x2d4)
[<c023d278>] (snd_soc_register_card+0x240/0x2d4) from [<c023d330>] (soc_probe+0x24/0x40)
[<c023d330>] (soc_probe+0x24/0x40) from [<c01c3900>] (platform_drv_probe+0x14/0x18)
[...]
The commit d3398ff059
( ASoC: Convert WM8753 to direct regmap API usage ) introduced
the problem.
Thanks to Lars-Peter Clausen for helping me a bit during the debugging.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Push everything through one function for active use cases, should be
no practical effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Normally this will have no effect as we set detection up at system startup
before DAPM syncs take effect, this will only be useful if the system
enables and disables detection at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811 DC servo is able to run much faster than previous devices so
the benefit of skipping calibration is not useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using snd_soc_write() means we always write to the register even if it
already contains the newly calculated value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Similar to what commit 1e3ad57 (ASoC: Remove redundant -codec from
WM8776 driver name) does for wm8776 driver, this patch does the same
thing for cs4270 driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the cache is currently open coded this is more of a win than for
most devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Don't use the internal I/O functions directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Early revisions of several of the WM8994 variants have register updates
to improve performance. Move these over to using the regmap patch system
instead of open coding them in the audio driver. Since the regmap init
is done by the MFD the code is moved there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
When an external capacitor is connected to MICBIAS2 on devices with
jack detection (which is not required but may be done in some systems)
then the loading may mean that better performance is obtained when
the microphone bias is enabled normally rather than using the low power
mode. Provide platform data allowing systems to indicate if they require
this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This minimises the chance of any external capacitors that are fitted
being discharged into headphones as they insert.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current ak4642 driver had wrong dapm settings for headphone L/R.
If you select headphone L, and select R after that,
headphone L setting was removed by R settings.
This patch fixes it up.
It provides just "Headphone Enable" to user side
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the printk(KERN_ERR* instances with dev_err in the driver.
While we are here clean up some of the debug messages as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8775 is register compatible with the WM8776 so can be supported with
the same driver though it is an ADC only part. Add the device ID to the
WM8776 driver, further updates will be added in the future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While it matches the current code only bringing the device out of reset
isn't actually doing what the function says so make sure we set the GPIO
high before we pull it low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows userspace control of final power off, allowing policy decisions
for register configuration retention.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only enable and disable the FLL when explicitly told to, supporting some
additional use cases and making the driver behaviour more standard.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we update for any changes in cases where we reconfigure while
live (eg, for analogue bypass).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Show the id we read when the id mismatch is detected.
This is useful for debugging.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The main role of the WM9081 is as a class D speaker amplifier so there
is no concern about pops. There are also very few registers and a fast
power up time so we can happily mark the driver as idle_bias_off.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Raise the ramp time to 50ms to cover corner cases, use the startup bias
generator, explicitly reset the ramp circuit when complete and reorder
things all of which should improve performance somewhat for systems that
are sensitive to noise from VMID.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The enable of the single ended line outputs on wm_hubs devices performs
better if the output is enabled prior to starting VMID. Since inactive
outputs are held at VMID anyway there is little cost to doing this for
unused outputs. Add callbacks into wm_hubs and keep track of which outputs
are really active so we can disable them once we're active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the mixer path diagram input sources' attenuators logically
belong to the playback path and DMIC boost only affects capture.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This brings the TLVs in sync with the documentation and allows to properly
manipulate mic boost controls with alsamixer.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch should fix output through speakers using HP mixer.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix I2S digital interface power for recording.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DMIC switches and controls to ALC5632 codec.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no Phone Mix<->Mono Mix route in datasheet.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename capture switches to common scheme XXX2REC.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove extra zero from volume step in DECLARE_TLV_DB_SCALE macro.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct spelling "memroy" to "memory" in
sound/soc/codecs/twl4030.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. the number of the half-beast?
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPMzv8AAoJEHm+PkMAQRiGgeYIAJxxGCxSMLRIiPaGRmQbWifs
eE3z6AUWitGfYvhmYdWVz+C/aa4pPCVWr3bAFxUQhu+ESmiFIiqiefvlTRf5f84e
pcoJFobkFfhtK4gLvUr75WxXDFq/1HhKqW1OLzIW4gQsnhMdjGJ3lLK6ZoRYH8h4
cGoN3DRII9mVLFcB2sgbeRvbQBA/O4n0aOQ2ryZkCcPQQMIKhR/rUEEV2pe/ovHE
rumQgI3PVey816P4e5YnOvrEAllFZlaZ/F0ClJgNdfeQCVTZx9KNRbiNxHi6fcC5
6Zgg7e5EvQTAy7QqQZ0hmS4k4CFmnswX3Nm+ZabRNqBdLSjPEDD9hk1o1dodYCg=
=BBLC
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc3' as we've got several bugfixes in there which are
colliding annoyingly with development.
Linux 3.3-rc3
.. the number of the half-beast?
Conflicts:
sound/soc/codecs/wm5100.c
sound/soc/codecs/wm8994.c
It's set unconditionally.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The VMID ramp rate is supposed to be 0x3, not 11b. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Make sure we generate enough BCLKs for I2S style modes by always having
a minimum of two channels worth of clocks for the BCLK.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No practical impact but now we have the control type we may as well use
it for the slightly nicer sequencing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we're not implementing GPIO or microphone detection support
there's no users for the read() function any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Make the mechanism used for WM8994 more like that for WM1811 and WM8958:
provide the logic to distinguish between headphone and headset and hard
code the reporting of sensible SND_JACK values. Should integration with
other detection mechanisms be required we can add appropriate callbacks
(though some integrations should be able to use the subsystem ones).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we might get an error if the GPIO is configured as an input
since that makes the register volatile and a suspended device can't be
read from.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the default state that the runtime PM infrastructure expects so
instead just kick the runtime PM core to suspend us if we're not doing
anything (as is default).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix build breakage by using the correct API call to add kcontrols.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Looks like nobody is or will be using this code.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In cases where we should enter STANDBY DAPM will power us up, otherwise
there is no need to power up and we can remain in OFF.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can enable VMID independently of the bias in some use cases so we need
to ensure that the core device is powered up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The second line output mixer has the controls for the line input bypasses
in the opposite order.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
For master mode, set Output [X|A|V]SP_SCLK Sourcing Mode to MCLK Mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. several days delayed. No reason, I just didn't think of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPKF4KAAoJEHm+PkMAQRiGw/YH+wXg2DpZUuHeBK52zMGlJBPc
DzX11/Uan3Y07gM0JbDzuVxwjX4vdxR2bV6r1qsLP8JEUnE8jyFC32DBGi5WAht7
F4KU/Uov2Ds5/wzvY4Iuo01C+JftQHXuy/Sbhck1d0LI0yjLejRaw+zuJv0x2/eS
7YqV+KTGE1lDuJs/Gyq1Vqr1g9831AuS1tv/g3gaqBuN6TcPBFCocaVxzwrUc+y6
94h26XbbOhQRIz38oqUkiqAGnvYS61ocyBcEiRHf0dXkNSDIINqlgukvd7YTXouA
jj/w/DWpMRcQuYAgqkrurr9+yWC9hVQcsvvQ5sAQnIPcxoR868sg1pO8Oheq+1g=
=kUzV
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc2' into for-3.4
A reasonable amount of new development is causing fiddly merge conflicts
between different resource management changes (mostly fixing bugs in
resource management due to noticing things while doing enhancements in
the same area).
Linux 3.3-rc2
.. several days delayed. No reason, I just didn't think of it.
For later wm_hubs devices we have much less need to keep the biases up
even when using single ended line outputs so flag idle_bias_off for
everything except the WM8993 and WM8994.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now we've switched over to regmap the ASoC level cache sync will be
ineffectual and potentially harmful as there is no longer an ASoC level
cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
IN1L/R is routed to both line output mixers, we don't route IN1 to LINEOUT1
and IN2 to LINEOUT2.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The Mute Switch should be called Playback Switch to match the volume
and the regmap core has been updated so we don't need to mark all the
registers as non-volatile.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC
drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver
for devices can unconditionally support idle_bias_off.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For optimal performance the single ended line outputs require that the
line output VMID buffer be enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Report any accessory with a low impedance as a headphone, previously
anything other than a short or microphone would not be reported at all.
The most likely reason is a microphone with incorrect polarity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using pm_runtime to decide if the device should go into full power down
has the dual advantage of allowing easier integration with non-DAPM
reasons to power on the device (like the FLL) and allowing userspace to
control the final power down which is useful for tuning retention of
DSP firmware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to avoid breakage change the omap-abe-twl6040
machine driver's routing.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to write the configuration for each microphone to a different
register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
When we have identified an accessory make sure we've flagged that we've
done so in order to make sure we always report buttons and don't continue
to polarity flip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the hardware is configured with one or both of the IN4 inputs used
for DC measurement (with no DC blocking capacitor connected) then we can
improve power consumption slightly in idle modes by applying a register
write sequence. Provide platform data to enable this, implemented using
a regmap patch.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In wm2000_i2c_probe(), if we take the true branch in
"
ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_wm2000,
NULL, 0);
if (ret != 0)
goto err_fw;
"
then we'll release_firmware(fw) at the 'err_fw' label. But we've already
done that just a few lines above. That's a use-after-free bug.
This patch restructures the code so that we always call
release_firmware(fw) before leaving the function, but only ever call
it once.
This means that we have to initialize 'fw' to NULL since some paths
may now end up calling it without having called request_firmware(),
but since request_firmware() deals gracefully with NULL pointers, we
are fine if we just NULL initialize it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To print a value of type size_t one should use %zd, not %d.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below build warning when CONFIG_HOTPLUG is not set.
CC sound/soc/codecs/alc5623.o
sound/soc/codecs/alc5623.c:1062: warning: ‘alc5623_i2c_remove’ defined but not used
CC sound/soc/codecs/alc5632.o
sound/soc/codecs/alc5632.c:1112: warning: ‘alc5632_i2c_remove’ defined but not used
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to table based DAPM and control init.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should be allowing a 5ms delay after the charge pump is started in
order to ensure it has finished ramping.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The problem was introduced due to the obscure formatting some of the
older drivers use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is more what the device model wants us to do and will allow use by
non-audio functions before the audio part of the device has come up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will allow us to move the interrupt allocation out of the ASoC part
of the driver and simplifies the locking by removing any reliance in the
bulk of the interrupt path on the big CODEC lock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Throughout the sgtl5000 driver source code and also in the sgtl5000 datasheet
the revision code is shown in hexadecimal.
Print it hex format, for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If an interrupt is supplied then use it for thermal warning and FLL lock
notifications. When using the interrupt raise the timeout for the FLL lock
substantially to reduce the chances of spurious warnings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This must be a leftover from a previous driver.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Much more compact, both in terms of source and especially in terms of
RAM used at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
remove unnecessary inclusion of machine specific header
file mach/dm365.h from cq93vc.c voice codec driver
which comes in the way of platform code consolidation.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a method for mach drivers to query the HS DC offset step size in mV.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The register map for this device is actually fairly sparse so the rbtree
should be beneficial.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensures that we get control of the CODEC earlier and don't try to probe
the card at all if register I/O isn't working.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Helps push the register cache code down out of ASoC and improves resume
times by using the more efficient regmap cache sync code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With a low frequency SYSCLK and a fast I2C clock register synchronisation
may occasionally take too long to take effect, causing I/O issues. Disable
synchronisation in order to avoid any issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
These are all to either uncached registers or fixes to register defaults,
in the former case the cache won't do anything and in the latter case
we're fixing things so the cache sync will do the right thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Writing to the registers won't work if we do actually manage to hit a fully
powered off state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Register LDOCTLEN must always be initialized to clear the analog power
control bit, otherwise the analog block will stay deactivated.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dividers (such as MDAC) are always needed, independent of the codec
being I2S master or slave. Needed on a custom board where the codec has
to be slave.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct SGTL5000_CHIP_CLK_CTRL to SGTL5000_CHIP_REF_CTRL in
sgtl5000_restore_regs(), and add comment to explain the
restore order.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Zeng Zhaoming <zengzm.kernel@gmail.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
ALSA: usb-audio: add Yamaha MOX6/MOX8 support
ALSA: virtuoso: add S/PDIF input support for all Xonars
ALSA: ice1724 - Support for ooAoo SQ210a
ALSA: ice1724 - Allow card info based on model only
ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
ALSA: hdspm - Provide unique driver id based on card serial
ASoC: Dynamically allocate the rtd device for a non-empty release()
ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
ALSA: hda/cirrus - support for iMac12,2 model
ASoC: cx20442: add bias control over a platform provided regulator
ALSA: usb-audio - Avoid flood of frame-active debug messages
ALSA: snd-usb-us122l: Delete calls to preempt_disable
mfd: Put WM8994 into cache only mode when suspending
...
Fix up trivial conflicts in:
- arch/arm/mach-s3c64xx/mach-crag6410.c:
renamed speyside_wm8962 to tobermory, added littlemill right
next to it
- drivers/base/regmap/{regcache.c,regmap.c}:
duplicate diff that had already come in with other changes in
the regmap tree
The DL1 PDM interface adds a little gain depending on the output device.
Add a method to retrieve the gain value for machine driver usage.
Signed-off-by: Liam Girdwood <lrg@ti.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (40 commits)
regulator: set constraints.apply_uV to 0 in of_get_fixed_voltage_config
regulator: max8925: fix enabled/disabled judgement mistake
regulator: add regulator_bulk_force_disable function
regulator: pass regulator_register of_node in fixed voltage driver
regulator: add regulator_force_disable() definition for !CONFIG_REGULATOR
regulator: Enable supply regulator if child rail is enabled.
regulator: mc13892: Convert to devm_kzalloc()
regulator: mc13783: Convert to devm_kzalloc()
regulator: Fix checking return value of create_regulator
regulator: Fix the error handling if create_regulator fails
regulator: Export regulator_is_supported_voltage()
regulator: mc13892: add device tree probe support
regulator: mc13892: remove the unnecessary prefix from regulator name
regulator: Convert wm831x regulator drivers to devm_kzalloc()
regulator: da9052: Staticize non-exported symbols
regulator: Replace kzalloc with devm_kzalloc and if-else with a switch-case for da9052-regulator
regulator: Update da9052-regulator for DT changes
regulator: DA9052/53 Regulator support
regulator: pass device_node to of_get_regulator_init_data()
regulator: If a single voltage is set with device tree then set apply_uV
...
Now that a regulator device for controlling the codec chip reset state
over a platform agnostic regulator API is available on the only board
using this driver so far, extend the driver with a bias control function
which will request virtual power to the codec chip from that virtual
regulator, and will supersede the present implementation existing at the
sound card level.
Thanks to the regulator sharing mechanism, both the old (the sound card)
and the new (the codec) implementations should coexist smoothly until
the sound card file is updated. For this to work as expected, update the
sound card .set_bias_level callback to not touch codec->dapm.bias_level.
While extending the cx20442 structure, drop unused control_type member.
Created against linxu-3.2-rc6, tested on top of patch 1/4 "ARM: OMAP1:
ams-delta: set up a regulator over the modem reset GPIO pin".
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
For a given ir and fs, there is at most one possible match for the case
mclk_ratios[ir][j].ratio * fs == freq.
Thus we can break from the inner loop once a match is found.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DA7210 has three line inputs (AUX1 Left, AUX1 Right and AUX2) and
a stereo MIC. This patch adds gain controls for MIC, AUX1, AUX2 as
well as INPGA.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert sgtl5000 codec driver to use devm_kzalloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
vdda, vddio and vddd are voltages expressed in milivolts (mV), so use the
proper annotation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Broken in commit d1dc698a54
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The module desciption says this is ASoC alc5621/2/3 driver.
Make the naming consistent with the reset of the code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We write the reset register with the default value so it should not be
mistakenly written.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use longer intervals when the microphone is not inserted to increase
robustness against leisurely insertion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that the mfd is using the register map cache there's no need for the
CODEC driver to do any register cache management or any funny dances to
interact with the other drivers using the device so just remove the cache
initialisation and volatility information.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Just go directly to the regmap API, saving code and making integration
that bit more direct.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a bunch of definitions for wm8994 registers that are not currently
used by software.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Record the clock after the divider as that is what all SYSCLK users see.
Without this the other clock configuration in the device comes out at
half rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows the device to be matched against the device tree using the
compatible flag directly, as is standard, rather than falling back to
matching .id_table against the non-vendor portion of the first compatible
property value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently SND_SOC_JZ4740_CODEC depends on SOC_JZ4740 but SOC_JZ4740 is not
defined in any Kconfig. Thus the codec driver will not be built when select
"Build all ASoC CODEC drivers".
(Unless it is selected by SND_JZ4740_SOC_QI_LB60).
Remove the dependency with SOC_JZ4740, then this code driver can be built when
select "Build all ASoC CODEC drivers".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Include linux/io.h to fix below build errors:
CC sound/soc/codecs/jz4740.o
sound/soc/codecs/jz4740.c: In function 'jz4740_codec_read':
sound/soc/codecs/jz4740.c:82: error: implicit declaration of function 'readl'
sound/soc/codecs/jz4740.c: In function 'jz4740_codec_write':
sound/soc/codecs/jz4740.c:92: error: implicit declaration of function 'writel'
sound/soc/codecs/jz4740.c: In function 'jz4740_codec_probe':
sound/soc/codecs/jz4740.c:373: error: implicit declaration of function 'ioremap'
sound/soc/codecs/jz4740.c:373: warning: assignment makes pointer from integer without a cast
sound/soc/codecs/jz4740.c:393: error: implicit declaration of function 'iounmap'
make[3]: *** [sound/soc/codecs/jz4740.o] Error 1
make[2]: *** [sound/soc/codecs] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we fail to read the IRQ type from the interrupt controller don't
fail, just assume a value and solider on - we may fail later when we try
to request the IRQ but it's possible we'll succeed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Document the device tree binding for the WM8903 codec, and modify the
driver to extract platform data from the device tree, if present.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the WM8903 is hooked up to an interrupt, set the irq_active_low flag
in the default platform data based on the IRQ's IRQ_TYPE. Map IRQ_TYPE_NONE
(a lack of explicit configuration/restriction) to irq_active_low = false;
the previous default.
This code is mainly added to support device tree interrupt bindings,
although will work perfectly well in a non device tree system too.
Any interrupt controller that supports only a single IRQ_TYPE could
set each IRQ's type based on that restriction. This applies equally
with and without device tree. To cater for interrupt controllers
that don't do this, for which irqd_get_trigger_type() will return
IRQ_TYPE_NONE, the platform data irq_active_low field may be used
in systems that don't use device tree.
With device tree, every IRQ must have some IRQ_TYPE set.
Controllers that support DT and multiple IRQ_TYPEs must define the
interrupts property (as used in interrupt source nodes) such that it
defines the IRQ_TYPE to use. When the core DT setup code initializes
wm8903->irq, the interrupts property will be parsed, and as a side-
effect, set the IRQ's IRQ_TYPE for the WM8903 probe() function to read.
Controllers that support DT and a single IRQ_TYPE could arrange to
set the IRQ_TYPE somehow during their initialization, or hard-code
it during the processing of the child interrupts property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The pdata pointer is now always valid. Remove any conditions that check
its validity.
This patch is mostly just removing an indentation level. One variable had
to be moved due to the removal of a scope, and one comment was split into
two. Viewing the patch with git show/diff -b will show that it's actually
very small.
Note that WM8903_MIC_BIAS_CONTROL_0 is now written unconditionally,
whereas it used to be written only if pdata was supplied. Since
defpdata.micdet_cfg = 0, this unconditional write simply echos the HW
defaults in the case where pdata is not supplied.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm8903_platform_data.gpio_cfg[] was intended to be interpreted as follows:
0: Don't touch this GPIO's configuration register
1..7fff: Write that value to the GPIO's configuration register
8000: Write zero to the GPIO's configuration register
other: Undefined (invalid)
The rationale is that platform data is usually global data, and a value of
zero means that the field wasn't explicitly set to anything (e.g. because
the field was new to the pdata type, and existing users weren't update to
initialize it) and hence the value zero should be ignored. 0x8000 is an
explicit way to get 0 in the register.
The code worked this way until commit 7cfe561 "ASoC: wm8903: Expose GPIOs
through gpiolib", where the behaviour was changed due to my lack of
awareness of the above rationale.
This patch reverts to the intended behaviour, and updates all in-tree users
to use the correct scheme. This also makes WM8903 consistent with other
devices that use a similar scheme.
WM8903_GPIO_NO_CONFIG is also renamed to WM8903_GPIO_CONFIG_ZERO so that
its name accurately reflects its purpose.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
reg_cache_size is supposed to be the number of elements in the register cache,
not the size in bytes.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using gpio_request_one can make the error handling simpler.
Also remove a redundant "Failed to issue reset" error message.
We already show the error message in uda1380_reset() error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return proper error for uda1380_modinit if i2c_add_driver() fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When no platform data is supplied, point pdata at a default platform
structure. This enables two future changes:
a) Defines the default platform data values in a single place.
b) There is always a valid pdata pointer, so some conditional code can
be simplified by a later patch.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get control of the device earlier and avoid trying to do an ASoC probe
on a card that won't work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Converting to an rbtree cache as regcache doesn't have a flat cache.
Since the top of the register map is fairly sparse this should be an
overall win.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
We only do this on initial power on so it's at best a waste of time as
the core will have already defaulted to the same values.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The driver used to use a complicated method to sync the register cache
after having brought the bias level up to standby in resume due to the
use of the write sequencer to manage the initial power up. Now that we
don't use the write sequencer there is no need for this and we can just
use snd_soc_cache_sync() directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Since they don't actually have power bits but do have events associated
with them it's important that we bootstrap their state properly which
making them virtual does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The GPIO registers are 15 bits wide. Hence values, higher than 0x7fff are
not legal GPIO register values. Modify the pdata.gpio_cfg handling code
to reject all illegal values, not just WM8903_GPIO_NO_CONFIG (0x8000). This
will allow the later use of 0xffffffff as an invalid value in future device
tree bindings, meaning "don't touch this GPIO's configuration".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The existence of this parameter is purely historical. None of the CODEC drivers
uses it and we always pass in the same value anyway, so it should be safe to
remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Still have a manual free in there for some realloc()ed memory as there's
no devm version of that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow systems to override the default microphone detection rates using
platform data in case the settings are not suitable (eg, due to an
unusually noisy jack).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to rerun DAPM if the clock source is the same but we do
need to adjust the microphone detection rate in case we are moving from
an audio to a non-audio rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811A features an advanced low power accessory detection subsystem
which allows the device to be maintained in a very low power state while
the system is idle without sacrificing any accessory detection features.
Implement software support for this, automatically managing the power
configuration of the device depending on the detected accessory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8958 and WM1811 support detecting a range of buttons. Allow the
user to provide platform data enabling more of these levels without
having to write a custom detection handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Actively manage the detection rate for microphones with WM8958, providing
improved power consumption and maximising the benefit from the hardware
debounce.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we don't have any active audio we can put the microphone biases into
bypass mode to save power at the expense of performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure SYSCLK is enabled while running accessory detection on WM8958.
It is always required so there is no sense in requiring machine drivers
to individually do this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for loading the SigmaDSP firmware using regmap. This allows us
to transparently use SPI or I2C as the transport protocol on devices which
support them.
For now we keep the old I2C support since we have one user of this which is not
straight forward to convert to regmap, due to variable length registers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the structs and functions only used by SigmaDSP firmware loader itself
from the header to the C file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide some error messages when loading the firmware fails, so it is possible
to diagnose the reason for the failure.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It has been pointed out previously, that the firmware subsystem is not the right
place for the SigmaDSP firmware loader. Furthermore the SigmaDSP is currently
only used in audio products and we are aiming for better integration into the
ASoC framework in the future, with support for ALSA controls for firmware
parameters and support dynamic power management as well. So the natural choice
for the SigmaDSP firmware loader is the ASoC subsystem.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
What we want is to clear BIT[5:4](PCM_MODE_MASK) and BIT[3](PCM_BIT_ORDER) bits,
but current code clears BIT[2:0].
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can reduce the code size here a bit by using snd_soc_update_bits instead of
open-coding the read-modify-write cycle. The conversion done in this patch is
not completely straightforward and some minor code restructuring has been
incorporated to further reduce the code size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a DAPM supply widget for the internal sysclk, so it can be disabled
automatically when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM route controls only take effect on paths where the sink is a mixer or a
mux, furthermore the control must be a control assigned to the mixer or mux.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also rename it to MICBIAS to reflect the pin name and help any out of tree
users notice the change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
It's never been updated so it can't be that useful and it makes the
driver needlessly chatty.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With device tree support for regulators, its needed that the
regulator_dev->dev device has the right of_node attached.
To be able to do this add an additional parameter to the
regulator_register() api, wherein the dt-adapted driver can
then pass this additional info onto the regulator core.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 85e7652("ASoC: Constify snd_soc_dai_ops structs") accidentally
introduced a few duplicated consts. This patch cleans it up.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Just checking the code in cs42l51_fill_cache():
The cache pointer points to codec->reg_cache + 1.
I think it is because CS42L51_FIRSTREG is 0x01,
so codec->reg_cache[0] is not used here.
Then we read CS42L51_NUMREGS bytes to cache.
So we need reg_cache_size to be CS42L51_NUMREGS + 1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the manual register restore mechanism in cs4270.c and call the
generic snd_soc_cache_sync() handler instead.
This factors code out in favour of core facilities and also fixes a
bus confusion that is most probably caused by intermixing i2c-regmap
functions and i2c_smbus_* accessors.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the case of ((max9877_regs[reg] >> shift) & mask) != val
but ((max9877_regs[reg2] >> shift) & mask) == val2,
current code does not update the registers.
Fix the logic to update registers if either val or val2 is changed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
The BIT[5:4] of ADC Control Register 2 is to control the word width.
00 = 25 Bits
01 = 20 Bits
10 = 16 Bits
11 = Invalid
Thus, the AD1836_ADC_WORD_OFFSET should be defined as 4.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Fix below smatch warning:
sound/soc/codecs/cs42l73.c +1030 cs42l73_set_dai_fmt(53) error: inv is never equal to 1024 (wrong type 0 - 255).
sound/soc/codecs/cs42l73.c +1032 cs42l73_set_dai_fmt(55) error: inv is never equal to 768 (wrong type 0 - 255).
sound/soc/codecs/cs42l73.c +1036 cs42l73_set_dai_fmt(59) error: inv is never equal to 1024 (wrong type 0 - 255).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code defines some bits with left shift to the proper bit defined in
datasheet, but some don't.
Unify the definition with proper left shift and adjust the code accordingly.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver only supports I2C so doesn't need to do things conditionally.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
They're all volatile so shouldn't have defaults and as we've got pages
into the DSP memory the registers themselves aren't that useful - a
further patch adding support for the DSPs will provide direct diagnostic
access to the DSP memories.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's done in cs42l73_set_bias_level when the dapm.bias_level is switching
from SND_SOC_BIAS_OFF to SND_SOC_BIAS_STANDBY.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return -ENODEV instead of 0 if device id mismatch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
the last entry from being omitted.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
There is no need to provide defaults for the volatile
registers and doing so might cause confusion.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch makes it possible to set DAI mode to its currently applied
value even if codec is active. This is necessary to allow
aplay -t raw -r 44100 -f S16_LE -c 2 < /dev/urandom &
alsactl store -f backup.state
alsactl restore -f backup.state
to work without returning errors. This patch is based on a patch sent
by Klaus Kurzmann <mok@fluxnetz.de>.
Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
There are two undocumented registers in use in alc5632_i2c_probe
function. It must be added to support future rewrite of this
function to use regmap API completely.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Cirrus Logic CS42L73 low power stereo
codec.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sta32x resets and loses all configuration during ESD test.
Work around by polling the CONFA register once a second
and restore all coeffcients and registers when CONFA
changes unexpectedly.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a structure for platform specific configuration and use it,
thereby removing a few FIXMEs which marked hard-coded values.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The coefficient RAM must be saved in a shadow so it can
be restored when the codec is powered on using
regulator_bulk_enable().
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Large code size increase due to the addition of readability information
and the reformatting of the defaults table.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get things configured as early as possible, especially useful for the
GPIOs which might be useful anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver implements basic functionality, using I²C for the control
channel.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
WM9081_BIAS_ENA is the bit[1] of WM9081_BIAS_CONTROL_1 register (05h).
Current code incorrectly write it to WM9081_VMID_CONTROL(04h) register.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
VMID Divider Enable and Select is controlled by BIT[2:1] of WM9081_VMID_CONTROL
register (04h).
Current code reads wrong register (WM9081_BIAS_CONTROL_1) for setting
VMID 2*240k.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This initial conversion just moves the register init, regulator acquisition
and device verification out to the I2C probe(). Movement of other parts of
the driver like the GPIO and beep generation code will follow.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that the WM8996 driver is using the regmap API for register I/O we no
longer need the ASoC card to be active in order to interact with the chip.
In order to be more idiomatic for Linux move most of the existing probe()
function out into the I2C probe() function prior to registration with ASoC.
The IRQ and GPIO init will be moved separately as these are slightly more
involved.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_update_bits already does read-modify-write,
no need to read the register before calling snd_soc_update_bits.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ak4642 was tested by ms7724se board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Occasionally we may see an accessory reported before we have a stable
impedance for the accessory. If this happens then reread the status in
order to ensure that the handler can take the appropriate action for the
status change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The thermal shutdown support in wm_hubs devices is tied to the speaker
drivers (which are the only high power subsystems within the device).
Ensure minimal current usage when the thermal shutdown support is not
required by disabling the circuit when the speaker drivers are powered
down.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Disable the thermal shutdown circuits for headphone and speaker when the
relevant outputs are not enabled in order to save current in idle modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM9081 thermal shutdown is only effective when the speaker output is
enabled so disable it when that is not in use for a small current saving.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Having a separate list for amps is a little confusing now the official
driver model for them is the same as for other CODECs so let's sort them
into the CODEC list, but only do this for those that are actual CODEC
drivers so it's easier to remember which ones need updating.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They aren't needed any more. If machines need them for other purposes then
further changes will be required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Force MICBIAS on as well as SYSCLK as the WM8962 accessory detection can't
function without both. No point in making machine drivers manually enable
it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we have code to automatically manage the start and stop of the FLL
based on the SYSCLK widget if SYSCLK is already enabled and the FLL is
configured then we need to start it up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since there is no current software control for these they would otherwise
be left enabled, consuming power.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The WM8962 has a separate software reset for the PLL registers. Ensure that
these are reset also on startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set `invert' bit for Capture Switch. Otherwise analogue is muted when
Capture Switch is ON.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Current implementation in wm8711_set_dai_fmt always clear BIT[3:2]
(the Input Audio Data Bit Length Select) of WM8711_IFACE(07h) register.
Input Audio Data Bit Length Select bits are set by wm8711_hw_params,
we should leave BIT[3:2] untouched in wm8711_set_dai_fmt.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The Input Audio Data Bit Length Select is controlled by BIT[3:2] of
WM8711_IFACE(07h) register.
Current code incorrectly masks BIT[1:0] which is for Audio Data Format Select.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
According to the datasheet:
Page0 / Register8: Audio Serial Data interface Control Register A
BIT 7: Bit Clock Directional Control
0: Bit clock is an input (slave mode)
1: Bit clock is an output (master mode)
BIT 6: Word Clock Directional Control
0: Word clock is an input (slave mode)
1: Word clock is an output (master mode)
Current code sets BIT_CLK_MASTER and WORD_CLK_MASTER bits for master mode,
but does not clear these bits for slave mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
Digital Audio Interface Format (07h) register:
BIT6: Master/slave mode
0: Slave
1: Master
Current code sets TLV320AIC23_MS_MASTER bit for master mode,
but does not clear it for slave mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
BCLK is controlled by BIT[4:2] of WM8940_CLOCK(06h) register.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Chris Paulson-Ellis <chris@edesix.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The registers are 16 bits, thus remove an extra F for the mask.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
The PLL Output clock division ratio is controlled by BIT[5:4] of
WM8940_GPIO register(08h).
Current code read/write the WM8940_ADDCNTRL(07h) register which is wrong.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
What we want here is to clear the WM8400_FLL_OUTDIV_MASK bits then
OR with factors.outdiv.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec->hw_write is broken now, convert codec->hw_write to snd_soc_write.
The hardware has 2 banks of registers sharing a section in I2C register space.
The 1st bank is the primary one and is cached.
The 2nd bank is for loading coefficients only and they do not need cache.
These coefficients registers are therefore direct writes.
Thus we set cache_bypass flag to deal with this before calling snd_soc_write.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure all mask bits are clear before setting new value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
DA7210 has three line outputs. OUT1 Left, OUT1 Right and OUT2 (mono).
This patch adds support for gain controls for these three line outs.
It also adds support for overall DAC gain control.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for DAPM covering all inputs and outputs
as well as ADC and DAC.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have defined SGTL5000_LINREG_VDDD_MASK in sgtl5000.h,
use it instead of hardcoded (0x1 << 4) - 1 for the mask.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise calling ldo_regulator_remove() does not unregister regulator
and free memories.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the register map in datasheet, the registers are 8 bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
BIT 2:1
VMID_SEL[1:0] VMID Divider Enable and Select
00 = VMID disabled
01 = 2x40k Omh divider
10 = 2x240k Omh divider
11 = 2x5k Omh divider
To set VMID 2*240k, we should OR reg with 0x04 instead of 0x40.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds controls to set following ALC parameters,
- Max gain, Min gain, Noise gain, Attack rate, Release rate and delay
It also adds a switch to enable/disable noise suppression.
As per DA7210 data sheet, ALC and noise suppression can be enabled
only if certain conditions are met. This condition checks are handled
by simply using "_EXT" version of controls to capture change events.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwod <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for below set of controls,
(1) Mute controls for MIC, AUX and ADC
(2) Zero cross controls for head phone, AUX, INPGA and line out
(3) Head phone mode selection - class H or G
It also adds digital_mute() call back.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not that we have interrupt handling in the driver at the minute.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
According to the datasheet:
CHIP_MIC_CTRL 0x002A
BITS[9:8] BIAS_RESISTOR
0x0 = Powerd off
0x1 = 2.0 kohm
0x2 = 4.0 kohm
0x3 = 8.0 kohm
To set mic bias resistor, we need to update bits[9:8] of
SGTL5000_CHIP_MIC_CTRL register.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
CHIP_MIC_CTRL 0x002A
BITS[9:8] BIAS_RESISTOR
0x0 = Powerd off
0x1 = 2.0 kohm
0x2 = 4.0 kohm
0x3 = 8.0 kohm
Thus SGTL5000_BIAS_R_MASK should be defined as 0x0300 instead of 0x0200.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
At least for the core controls, the optionally selected controls are still
added programatically.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Evaluation of larger quantities of material has provided new DCS codes
values to be applied for WM1811.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now we have done bitwise NOT against the mask bits for the defines of
WM8900_REG_CLOCKING1_BCLK_MASK,
WM8900_REG_CLOCKING1_OPCLK_MASK and WM8900_LRC_MASK.
But we don't have the bitwise NOT against the mask bits for the defines of
WM8900_REG_CLOCKING2_DAC_CLKDIV,
WM8900_REG_CLOCKING2_ADC_CLKDIV and WM8900_REG_DACCTRL_AIF_LRCLKRATE.
It is error prone to mix the inconsistent meaning for different mask defines.
So lets make the defines for each mask to be corresponding to the bits
defines in datasheet. Don't add extra "bitwise NOT" to the defines.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After checking the datasheet, I think what we want to do here is to
clear the WM8900_REG_CLOCKING2_DAC_CLKDIV/WM8900_REG_CLOCKING2_ADC_CLKDIV/
WM8900_REG_DACCTRL_AIF_LRCLKRATE bits and then OR with div value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
Format Control (05h)
BITS[3:2]
FMT[1:0] Audio data format selection
00 = right justified mode
01 = left justified mode
10 = I2S mode
11 = DSP mode
BIT[4] LRP Polarity selec for LRCLK/DSP mode select
0 = normal LRCLK poalrity/DSP mode A
1 = inverted LRCLK poarity/DSP mode B
For SND_SOC_DAIFMT_DSP_A, we should set 0x000C instead of 0x0003.
For SND_SOC_DAIFMT_DSP_B, we should set 0x001C instead of 0x0013.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This patch add controls for setting cut-off for high pass and voice
filters of ADC and DAC. There are also switches to enable/disable
these filters.
Also removed hard coded, fixed values of these parameters used by
previous version of driver.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for ADC and DAC five band equalizers
available on DA7210 codec.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to have as less time between McPDM shutdown,
and power down of the DAC on the twl6040 codec as possible.
Request core to ignore the pmdown_time for the playback
stream.
Backround: with the McPDM protocol we are sendning not only
the pure audio stream, but OMAP McPDM also transmits
additional information (for example offset cancellation).
If McPDM is stopped prior to the DAC this information will
be not sent to the codec, which can result noise rendered
by the twl6040 codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch takes care of reserved bits of headphone volume
register by using correct volume range.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code defines AD193X_PLL_INPUT_MASK as (~0x6) which is quite
different from other MASK defines.
To make it consistent with other mask defines, define AD193X_PLL_INPUT_MASK
as 0x6 and change the code accordingly.
I think this change improves the readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
This patch also includes a comment fix in wm8990_set_dai_pll(),
if freq_in and freq_out are 0, what we do is to clear WM8990_PLL_ENA bit.
Thus the comment should be "Turn off PLL".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If (fakepower & ((1 << WM8990_INMIXR_PWR_BIT) | (1 << WM8990_AINRMUX_PWR_BIT)))
is false, we should clear WM8990_AINR_ENA bits instead of WM8990_AINL_ENA.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If (fakepower & ((1 << WM8400_INMIXR_PWR) | (1 << WM8400_AINRMUX_PWR)))
is false, we should clear WM8400_AINR_ENA bits instead of WM8400_AINL_ENA.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If (fakepower & ((1 << WM8991_INMIXR_PWR_BIT)|(1 << WM8991_AINRMUX_PWR_BIT))))
is false, we should clear WM8991_AINR_ENA bits instead of WM8991_AINL_ENA.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec->hw_read is broken now, let's covert to snd_soc_read.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec->hw_read is broken now, let's covert to snd_soc_read.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec->hw_read is broken now, let's covert to snd_soc_read.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the event handler is only used by the Earphone Driver, it is better
to rename it from twl6040_power_mode_event to twl6040_ep_drv_event.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is better to switch HS Power Mode (if it was in low power mode) before
we enable the Earpiece driver. The switched off EP driver can filter out
noise coming from the Low Power to High Performance transition on the
HSL DAC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no limitation dictated by outputs or inputs regarding to the
selected PLL (LP/HP).
Remove the checks for this, and allow all path with any PLL configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Capture is supported in all PLL configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ak4535_reg should be 8bit, but cache table is defined as 16bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
ak4642 register was 8bit, but cache table was defined as 16bit.
ak4642 doesn't work correctry without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Chip documentation explicitly requires that the reset values
of reserved register bits are left untouched.
codec->hw_read is broken now.
Here we use below trick to avoid writing to reserved registers while resume.
Write the register default value to cache for reserved registers,
so the write to the these registers are suppressed by the cache
restore code when it skips writes of default registers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patchs adds support for following,
(1) DAI 20 and 32 bit word sizes
(2) DAI left and right justified formats
(3) DAI slave mode
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both Headset DAC need to be turned on/off at the same time before
any of the output drivers are enabled (HS Left/Right, Earpiece).
Move the HS DAC enable code to sequenced DAPM_SUPPLY, and attach
it to the DACs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
twl6040 have two vibra output drivers.
They can be operated with audio stream coming through
the PDM interface (fifth channel).
The vibra outputs can be controlled via the input/FF
driver as well.
Selection between the two mode is implemented within
the codec driver, the input/FF driver can only operate if
the routing is set to "Input FF".
Changing from "Input FF" to "Audio PDM" mode is protected
as well: The switchin can only be done, if there is no
running effect from the input/FF.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We set hw_params callback for wm8994_aif3_dai_ops to wm8994_aif3_hw_params.
Thus no need to check wm8994-aif3 in wm8994_hw_params.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after multi-component patch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5100 includes an advanced, low power, accessory detect subsystem
capable of detecting both accessory presence and button presses while
the device is in an ultra low power mode. Implement initial support for
this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is currently named "TVL" instead of "TLV".
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8983 can be reset by performing a write of any value to
the software reset register.
To avoid writing to the software reset register while resume,
we should write the same value in wm8983_reg_defs to software
reset register in wm8983_probe().
The write to the reset register is suppressed by the cache
restore code when it skips writes of default registers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We really should be doing this in the core, not in a driver...
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Checking the pdata-flags used 'or', so the check is always true. Use 'and' to
correctly mask the flags.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The snd_soc_*_volsw_2r functionality has been merged to
*volsw callbacks.
Few places still used the get, or put variant of volsw_2r,
replace those with the corresponding *_volsw.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Eliminate below build warning:
CC sound/soc/codecs/wm9090.o
sound/soc/codecs/wm9090.c: In function 'wm9090_probe':
sound/soc/codecs/wm9090.c:550: warning: unused variable 'wm9090'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Let the user know, that the callback has been called with unexpected
register parameter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ASoC core now have one callback function, which can handle
single, and double register mixer controls.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Avoid using the mc->rreg to identify the 2r type of gain control.
Introduce a variable to track this.
This change is needed to avoid breakage with the upcoming volsw volsw_2r
merger.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The custom get_volsw does not need to call any core get_volsw calls,
since we are returning the shadow values for the gains.
Return -EINVAL in the unlikely event, if the function has been called
for unhandled control. This way we can remove one check in the code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the macros for controls require custom get/put function.
This is to make sure that the soc_mixer_control is used
consistently among the drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Arun KS <arunks@mistralsolutions.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return -EINVAL in the unlikely event, if the function has been called
for unhandled control. This way we can remove one check in the code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not required after commit 8d50e447
"ASoC: Factor out I/O for Wolfson 8 bit data 16 bit register CODECs"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Writing to WM8971_RESET resets all registers to the default state.
Thus we should avoid writing to WM8971_RESET on resume.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For wm8994-aif2, the rate_reg should be WM8994_AIF2_RATE.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
snd_soc_update_bits() will only write new register value
if the old value is different from the new value.
In additional, snd_soc_update_bits() returns 0 for no change.
No need to read WM8995_CLOCKING_1 register before calling snd_soc_update_bits().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_update_bits() will only write new register value
if the old value is different from the new value.
In additional, snd_soc_update_bits() returns 0 for no change.
No need to read WM8994_CLOCKING_1 register before calling snd_soc_update_bits().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the biquad channel names to a separate array and iterate over it in
max98095_get_bq_channel rather than duplicating the hardcoded channel
names. Add an error message if an invalid channel is passed and check
the error in the callers.
Also added a BUILD_BUG_ON to ensure that the bq_mode_name and controls
arrays are the same size.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the EQ channel names to a separate array and iterate over it in
max98088_get_channel rather than duplicating the hardcoded channel
names. Add an error message if an invalid channel is passed and check
the error in the callers.
Also added a BUILD_BUG_ON to ensure that the eq_mode_name and controls
arrays are the same size.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811 is mostly register compatible with the WM8994 and WM8958,
providing a high performance audio hub CODEC in a small form factor
suitable for ultra compact system designs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After checking the code and datasheet, I think what we want in the second
snd_soc_update_bits call is to update WM8741_DACRMSB_ATTENUATION register
instead of WM8741_DACRLSB_ATTENUATION.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This assignment is done by the snd_soc_register_codec so there is no need
to redo it in probe function of a codec driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the comments in include/linux/init.h:
"Pointers to __devexit functions must use __devexit_p(function_name), the
wrapper will insert either the function_name or NULL, depending on the config
options."
We have __devexit annotation for wm8782_remove(), thus add __devexit_p at
necessary place.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code set update bits for WM8753_LDAC and WM8753_RDAC twice,
but missed setting update bits for WM8753_LADC and WM8753_RADC.
I think it is a copy-paste bug in commit 776065
"ASoC: codecs: wm8753: Fix register cache incoherency".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Save model information in driver_data so we can simplify the implementation.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead of checking, if the work is pending, it is safer to cancel
the pending work, or wait till the scheduled work finishes.
This way we can avoid modifying the variables used by the work
function.
Since we know that no work is pending, we can remove the two additional
checks in POST_PMU, and PRE_PMD for non pending works.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
None of the driver handled by out_drv_event have it's power
bit shifted by 3.
Remove the case for shift 3, and also add comment for the cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Headset gain range is 0 - 0xf (4 bit resolution)
The Handsfree gain range is 0 - 0x1d (5 bit resolution,
0x1e, and 0x1f values are invalid)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is a bit overkill to have three (3) separate
workqueue for a single driver.
We can manage things with one workqueue nicely.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No reason to use static variable for channel_index.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The control_data field is used to initialize the codec's control_data field,
but since this is also done by the snd-soc-cache core, the redundant
assignment can be removed and the field can be dropped.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The control_data field is used to initialize the codec's control_data field,
but since this is also done by the snd-soc-cache core, the redundant
assignment can be removed and the field can be dropped.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
