Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for allowing drivers to sleep in
ampdu_action, change the locking in the TX
aggregation code to use the mutex the RX part
already uses. The spinlock is still necessary
around some code to avoid races with TX, but
now we can also synchronize_net() to avoid
getting an inconsistent sequence number.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we want the code to be able to sleep
in the future, it must not be called from
the timer directly. To achieve that, simply
call the function drivers would call, and
also use RCU in the timer to get the struct
so we don't need to rely on the spinlock in
the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for allowing drivers to sleep in
ampdu_action, change the locking in the RX
aggregation code to use a mutex, so that it
would already allow drivers to sleep. But
explicitly disable BHs around the callback
for now since the TX part cannot yet sleep,
and drivers' locking might require it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed that when there was _no_ traffic at
all on a given aggregation session, it would
never time out. This won't happen unless you
forced creating a session, but fix it anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we want the code to be able to sleep
in the future, it must not be called from
the timer directly. To prepare, move it out
into the aggregation work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the block-ack session works into common
code, since it will be needed for RX agg too
in the next patches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver or rate control requests starting
or stopping an aggregation session, that currently
causes a direct callback into the driver, which
could potentially cause locking problems. Also,
the functions need to be callable from contexts
that cannot sleep, and thus will interfere with
making the ampdu_action callback sleeping.
To address these issues, add a new work item for
each station that will process any start or stop
requests out of line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently maintains the ampdu_lock to
avoid starting a queue due to one aggregation
session while another aggregation session needs
the queue stopped.
We can do better, however, and instead refcount
the queue stops for this particular purpose,
thus removing the need for the lock. This will
help making ampdu_action able to sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The non-irqsafe aggregation start/stop done
callbacks are currently only used by ath9k_htc,
and can cause callbacks into the driver again.
This might lead to locking issues, which will
only get worse as we modify locking. To avoid
trouble, remove the non-irqsafe versions and
change ath9k_htc to use those instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we allocate some memory for each TX
aggregation session and additionally keep a
state bitmap indicating the state it is in.
By using RCU to protect the pointer, moving
the state into the structure and some locking
trickery we can avoid locking when the TX agg
session is fully operational.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we allocate some memory for each RX
aggregation session and additionally keep a
flag indicating whether or not it is valid.
By using RCU to protect the pointer and making
sure that the memory is fully set up before it
becomes visible to the RX path, we can remove
the need for the bool that indicates validity,
as well as for locking on the RX path since it
is always synchronised against itself, and we
can guarantee that all other modifications are
done when the structure is not visible to the
RX path.
The net result is that since we remove locking
requirements from the RX path, we can in the
future use any kind of lock for the setup and
teardown code paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the aggregation callback processing
to the per-sdata skb queue and a work function
rather than the tasklet.
Unfortunately, this means that it extends the
pkt_type hack to that skb queue. However, it
will enable making ampdu_action API changes
gradually, my current plan is to get rid of
this again by forcing drivers to only return
from ampdu_action() when everything is done,
thus removing the callbacks completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a corner case where we receive a fragmented
frame during a blockack session, in which case we
will terminate that session. To simplify future work
in this area that will culminate in allowing the
driver callbacks for aggregation to sleep, move the
processing of this case out of the RX path into the
interface work.
This will simplify future work because the new place
for this code doesn't require that the function will
always be atomic, which the RX path needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for making the ampdu_action callback
sleep, make mac80211 always process blockack
action frames from the skb queue. This gets rid
of the current special case for managed mode
interfaces as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some code is duplicated between ibss, mesh and
managed mode regarding the queueing of management
frames. Since all modes now use a common skb
queue and a common work function, we can pull
the queueing code into the rx handler directly
and remove the duplicated length checks etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the management processing functions free the
skb after they are done, so this can be done in
the new common code instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even with the previous patch, IBSS, managed
and mesh modes all attach their own work
function to the shared work struct, which
means some duplicated code. Change that to
only have a frame processing function and a
further work function for each of them and
share some common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS, managed and mesh modes all have their
own work struct, and in the future we want
to also use it in other modes to process
frames from the now common skb queue.
This also makes the skb queue and work safe
to use from other interface types.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS, managed and mesh modes all have an
skb queue, and in the future we want to
also use it in other modes, so make them
all use a common skb queue already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of places use RCU locking for accessing
the station list, even though they do not need
to. Use mutex locking instead to prepare for the
locking changes I want to make. The mlme code is
also using a WLAN_STA_DISASSOC flag that has the
same meaning as WLAN_STA_BLOCK_BA, so use that.
While doing so, combine places where we loop
over stations twice, and optimise away some of
the loops by checking if the hardware supports
aggregation at all first.
Also fix a more theoretical race condition: right
now we could resume, set up an aggregation session,
and right after tear it down again due to the code
that is needed for hardware reconfiguration here.
Also mark add a comment to that code marking it as
a workaround.
Finally, remove a pointless aggregation disabling
loop when an interface is stopped, directly after
that we remove all stations from it which will also
disable all aggregation sessions that may still be
active, and does so in a race-free way unlike the
current loop that doesn't block new sessions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When in IBSS mode, currently action frame TX and RX
cannot be used. Allow using it to talk to any peer,
or for public action frames. Also, while at it,
restructure the code in mac80211 to make it easier
to add this for other interface types in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we receive a deauthentication frame before
having successfully associated, we neither print
a message nor abort assocation. The former makes
it hard to debug, while the latter later causes
a warning in cfg80211 when, as will typically be
the case, association timed out.
This warning was reported by many, e.g. in
https://bugzilla.kernel.org/show_bug.cgi?id=15981,
but I couldn't initially pinpoint it. I verified
the fix by hacking hostapd to send a deauth frame
instead of an association response.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a window for ieee80211_ifa_changed() to get called whilst the
managed mode mutex has not been initialized when opening and stopping the
interface. Currently this causes a kernel BUG like the following:
[ 132.460013] kernel BUG at /home/wifi/iwlwifi-2.6/net/mac80211/main.c:380!
[ 132.460013] invalid opcode: 0000 [#1] SMP
The mutex is initialized during open(), hence once netif_running() is true,
the mutex should be valid. Fix by adding a netif_running() check to the
function.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: make ARP filtering depend on CONFIG_INET" introduced this
potential locking leak.
Reported-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes "iw wlan0 dump survey" work again with
mac80211-based drivers that support it, e.g. ath5k.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Processing an association response could take a bit
of time while we set up the hardware etc. During that
time, the AP might already send a blockack request.
If this happens very quickly on a fairly slow machine,
we can end up processing the blockack request before
the association processing has finished. Since the
blockack processing cannot sleep right now, we also
cannot make it wait in the driver.
As a result, sometimes on slow machines the iwlagn
driver gets totally confused, and no traffic can pass
when the aggregation setup was done before the assoc
setup completed.
I'm working on a proper fix for this, which involves
queuing all blockack category action frames from a
work struct, and also allowing the ampdu_action driver
callback to sleep, which will generally clean up the
code and make things easier.
However, this is a very involved and complex change.
To fix the problem at hand in a way that can also be
backported to stable, I've come up with this patch.
Here, I simply process all aggregation action frames
from the managed interface skb queue, which means
their processing will be serialized with processing
the association response, thereby fixing the problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
STA_NOTIFY_ADD and STA_NOTIFY_REMOVE have no users anymore,
and station addition/removal are indicated to drivers
using sta_add() and sta_remove(), which can sleep.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reduces the binary size by around 25k (measured on MIPS,
with CONFIG_MAC80211_DEBUG_COUNTERS enabled).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since I recently made station management able
to sleep, I can now rework key management as
well; since it will no longer need a spinlock
and can also use a mutex instead, a bunch of
code to allow drivers' set_key to sleep while
key management is protected by a spinlock can
now be removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some odd reason, the plink_state enum is
declared in the middle between aggregation
related structures. Move it down to make the
file easier to read.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After ieee80211_rx_h_ctrl() processing we only
want to process management (including action)
frames, so there's no point in letting control
frames continue.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since we use only cfg80211 for configuration,
there is no configuration that could be pending at
this point, cfg80211 will have the configuration
that is pending and apply it afterwards.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I suspect the compiler will do this optimisation
anyway, but it seems cleaner to move this into
the WEP switch case.
Also make rx_h_decrypt use a local variable for
the frame_control so that we don't need to reload
the hdr variable for this after linearizing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no sense in letting anything but internal
mac80211 functions set the initiator to anything
but WLAN_BACK_INITIATOR, since WLAN_BACK_RECIPIENT
is only valid when we have received a frame from
the peer, which we react to directly in mac80211.
The debugfs code I recently added got this wrong
as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware allow extended filtering of ARP frames not intended for
the host. To perform such filtering, the hardware needs to know the current
IP address(es) of the host, bound to its interface.
Add support for ARP filtering to mac80211 by adding a new op to the driver
interface, allowing to configure the current IP addresses. This op is called
upon association with the currently configured address(es), and when
associated whenever the IP address(es) change.
This patch adds configuration of IPv4 addresses only, as IPv6 addresses don't
need ARP filtering.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS code has a bogus mod_timer(..., 0) call,
we shouldn't ever pass a constant value to the
function since any constant value could be in the
future or the past.
However, invoking the timer here is not necessary
at all, since we just finished scanning and just
need to have the IBSS code run again from the
workqueue later, so factor out the work starting
and use that instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending action frames, we want to verify
that we do that on the correct channel. However,
checking the channel type in addition can get in
the way, since the channel type could change on
the fly during an association, and it's not
useful to have the channel type anyway since it
has no effect on the transmission. Therefore,
make it optional to specify so that if wanted,
it can still be checked, but is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't refuse HT20 channels on devices that don't support HT40.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dialog token allocator has apparently been broken
since b83f4e15 ("mac80211: fix deadlock in sta->lock")
because it got moved out under the spinlock. Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel reported that the paged RX changes had
broken blockack request frame processing due
to using data that wasn't really part of the
skb data.
Fix this using skb_copy_bits() for the needed
data. As a side effect, this adds a check on
processing too short frames, which previously
this code could do.
Reported-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse correctly complains that
__ieee80211_get_channel_mode is not static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix sta_info.h kernel-doc warnings:
Warning(net/mac80211/sta_info.h:164): No description found for parameter 'tid_active_rx[STA_TID_NUM]'
Warning(net/mac80211/sta_info.h:164): Excess struct/union/enum/typedef member 'tid_state_rx' description in 'sta_ampdu_mlme'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specifying a valid channel type will get
goto out rather than continuing, due to
missing braces. This affects both remain
on channel and action frame TX commands.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since wdev can be NULL, check it before dereferencing it
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
signal_type is enum cfg80211_signal_type.
This fixes the gcc warning:
scan.c: In function `cfg80211_inform_bss':
scan.c:518:6: warning: comparison between `enum cfg80211_signal_type' and `enum nl80211_bss'
scan.c: In function `cfg80211_inform_bss_frame':
scan.c:574:6: warning: comparison between `enum cfg80211_signal_type' and `enum nl80211_bss'
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some issues introduced in batch skb dequeuing for input_pkt_queue.
The primary issue it that the queue head must be incremented only
after a packet has been processed, that is only after
__netif_receive_skb has been called. This is needed for the mechanism
to prevent OOO packet in RFS. Also when flushing the input_pkt_queue
and process_queue, the process queue should be done first to prevent
OOO packets.
Because the input_pkt_queue has been effectively split into two queues,
the calculation of the tail ptr is no longer correct. The correct value
would be head+input_pkt_queue->len+process_queue->len. To avoid
this calculation we added an explict input_queue_tail in softnet_data.
The tail value is simply incremented when queuing to input_pkt_queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When GRO produces fraglist entries, and the resulting skb hits
an interface that is incapable of TSO but capable of FRAGLIST,
we end up producing a bogus packet with gso_size non-zero.
This was reported in the field with older versions of KVM that
did not set the TSO bits on tuntap.
This patch fixes that.
Reported-by: Igor Zhang <yugzhang@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
This race was triggered by a 'conntrack -F' command running in parallel
to the insertion of a hash for a new connection. Losing this race led to
a dead conntrack entry effectively blocking traffic for a particular
connection until timeout or flushing the conntrack hashes again.
Now the check for an already dying connection is done inside the lock.
Signed-off-by: Joerg Marx <joerg.marx@secunet.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* 'for-2.6.35' of git://linux-nfs.org/~bfields/linux: (45 commits)
Revert "nfsd4: distinguish expired from stale stateids"
nfsd: safer initialization order in find_file()
nfs4: minor callback code simplification, comment
NFSD: don't report compiled-out versions as present
nfsd4: implement reclaim_complete
nfsd4: nfsd4_destroy_session must set callback client under the state lock
nfsd4: keep a reference count on client while in use
nfsd4: mark_client_expired
nfsd4: introduce nfs4_client.cl_refcount
nfsd4: refactor expire_client
nfsd4: extend the client_lock to cover cl_lru
nfsd4: use list_move in move_to_confirmed
nfsd4: fold release_session into expire_client
nfsd4: rename sessionid_lock to client_lock
nfsd4: fix bare destroy_session null dereference
nfsd4: use local variable in nfs4svc_encode_compoundres
nfsd: further comment typos
sunrpc: centralise most calls to svc_xprt_received
nfsd4: fix unlikely race in session replay case
nfsd4: fix filehandle comment
...
* 'nfs-for-2.6.35' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (78 commits)
SUNRPC: Don't spam gssd with upcall requests when the kerberos key expired
SUNRPC: Reorder the struct rpc_task fields
SUNRPC: Remove the 'tk_magic' debugging field
SUNRPC: Move the task->tk_bytes_sent and tk_rtt to struct rpc_rqst
NFS: Don't call iput() in nfs_access_cache_shrinker
NFS: Clean up nfs_access_zap_cache()
NFS: Don't run nfs_access_cache_shrinker() when the mask is GFP_NOFS
SUNRPC: Ensure rpcauth_prune_expired() respects the nr_to_scan parameter
SUNRPC: Ensure memory shrinker doesn't waste time in rpcauth_prune_expired()
SUNRPC: Dont run rpcauth_cache_shrinker() when gfp_mask is GFP_NOFS
NFS: Read requests can use GFP_KERNEL.
NFS: Clean up nfs_create_request()
NFS: Don't use GFP_KERNEL in rpcsec_gss downcalls
NFSv4: Don't use GFP_KERNEL allocations in state recovery
SUNRPC: Fix xs_setup_bc_tcp()
SUNRPC: Replace jiffies-based metrics with ktime-based metrics
ktime: introduce ktime_to_ms()
SUNRPC: RPC metrics and RTT estimator should use same RTT value
NFS: Calldata for nfs4_renew_done()
NFS: Squelch compiler warning in nfs_add_server_stats()
...
* 'bkl/procfs' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing:
sunrpc: Include missing smp_lock.h
procfs: Kill the bkl in ioctl
procfs: Push down the bkl from ioctl
procfs: Use generic_file_llseek in /proc/vmcore
procfs: Use generic_file_llseek in /proc/kmsg
procfs: Use generic_file_llseek in /proc/kcore
procfs: Kill BKL in llseek on proc base
This patch ensures that all places that schedule the DAD timer
look at the address state in a safe manner before scheduling the
timer. This ensures that we don't end up with pending timers
after deleting an address.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of the new POSTDAD state. This prevents
a race between DAD completion and failure.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of the new state_lock to synchronise between
updates to the ifa state. This fixes the issue where a remotely
triggered address deletion (through DAD failure) coincides with a
local administrative address deletion, causing certain actions to
be performed twice incorrectly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the boolean dead flag on inet6_ifaddr with
a state enum. This allows us to roll back changes when deleting
an address according to whether DAD has completed or not.
This patch only adds the state field and does not change the logic.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build when CONFIG_SYSFS is not enabled:
net/bridge/br_if.c:136: error: 'struct net_bridge_port' has no member named 'sysfs_name'
Note: dev->name == sysfs_name except when change name is in
progress, and we are protected from that by RTNL mutex.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from net/ (but not any netfilter files)
all the unnecessary return; statements that precede the
last closing brace of void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user has a bad classification configuration, and gets a packet
that goes through too many steps. Chances are more packets will arrive,
and the message spew will overrun syslog because it is not rate limited.
And because it is not tagged with appropriate priority it can't not be screened.
Added the qdisc to the message to try and give some more context when
the message does arrive.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put severity level on pfkey printk messages
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Serious oh sh*t messages converted to WARN().
Add KERN_NOTICE severity to the unknown policy type messages.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch encourage me to go look at all the messages in
the network scheduler and fix them. Many messages were missing
any severity level. Some serious ones that should never happen
were turned into WARN(), and the random noise messages that were
handled changed to pr_debug().
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than the combination of kmalloc and memset.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5fa782c2f5
sctp: Fix skb_over_panic resulting from multiple invalid \
parameter errors (CVE-2010-1173) (v4)
cause 'error cause' never be add the the ERROR chunk due to
some typo when check valid length in sctp_init_cause_fixed().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new netdev ops ndo_{set|get}_vf_port to allow setting of
port-profile on a netdev interface. Extends netlink socket RTM_SETLINK/
RTM_GETLINK with two new sub msgs called IFLA_VF_PORTS and IFLA_PORT_SELF
(added to end of IFLA_cmd list). These are both nested atrtibutes
using this layout:
[IFLA_NUM_VF]
[IFLA_VF_PORTS]
[IFLA_VF_PORT]
[IFLA_PORT_*], ...
[IFLA_VF_PORT]
[IFLA_PORT_*], ...
...
[IFLA_PORT_SELF]
[IFLA_PORT_*], ...
These attributes are design to be set and get symmetrically. VF_PORTS
is a list of VF_PORTs, one for each VF, when dealing with an SR-IOV
device. PORT_SELF is for the PF of the SR-IOV device, in case it wants
to also have a port-profile, or for the case where the VF==PF, like in
enic patch 2/2 of this patch set.
A port-profile is used to configure/enable the external switch virtual port
backing the netdev interface, not to configure the host-facing side of the
netdev. A port-profile is an identifier known to the switch. How port-
profiles are installed on the switch or how available port-profiles are
made know to the host is outside the scope of this patch.
There are two types of port-profiles specs in the netlink msg. The first spec
is for 802.1Qbg (pre-)standard, VDP protocol. The second spec is for devices
that run a similar protocol as VDP but in firmware, thus hiding the protocol
details. In either case, the specs have much in common and makes sense to
define the netlink msg as the union of the two specs. For example, both specs
have a notition of associating/deassociating a port-profile. And both specs
require some information from the hypervisor manager, such as client port
instance ID.
The general flow is the port-profile is applied to a host netdev interface
using RTM_SETLINK, the receiver of the RTM_SETLINK msg communicates with the
switch, and the switch virtual port backing the host netdev interface is
configured/enabled based on the settings defined by the port-profile. What
those settings comprise, and how those settings are managed is again
outside the scope of this patch, since this patch only deals with the
first step in the flow.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb rxhash should be cleared when a skb is handled by a tunnel before
being delivered again, so that correct packet steering can take place.
There are other cleanups and accounting that we can factorize in a new
helper, skb_tunnel_rx()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 33ad798c92 (tcp: options clean up) introduced a problem
if MD5+SACK+timestamps were used in initial SYN message.
Some stacks (old linux for example) try to negotiate MD5+SACK+TSTAMP
sessions, but since 40 bytes of tcp options space are not enough to
store all the bits needed, we chose to disable timestamps in this case.
We send a SYN-ACK _without_ timestamp option, but socket has timestamps
enabled and all further outgoing messages contain a TS block, all with
the initial timestamp of the remote peer.
Fix is to really disable timestamps option for the whole session.
Reported-by: Bijay Singh <Bijay.Singh@guavus.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The duplicate address check code got broken in the conversion
to hlist (2.6.35). The earlier patch did not fix the case where
two addresses match same hash value. Use two exit paths,
rather than depending on state of loop variables (from macro).
Based on earlier fix by Shan Wei.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attaching filters to a class pointing to a class higher up in the
hierarchy, classification may enter an endless loop. Currently this is
prevented for filters that are already resolved, but not for filters
resolved at runtime.
Only allow filters to point downwards in the hierarchy, similar to what
CBQ does.
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several netem users use TBF for rate control. But every time the parameters
of TBF are changed it destroys the child qdisc, requiring reconfigation.
Better to just keep child qdisc and just notify it of changed limit.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also added an explicit break; to avoid
a fallthrough in net/ipv4/tcp_input.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes the BKL in x25 setsock and getsockopts.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the x25 accept approve flag from char into bitfield.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the x25 interrupt flag from char into bitfield.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the X25 q bit flag from char into a bitfield to allow BKL cleanup.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP outgoing packets can avoid two atomic ops, and dirtying
of previously higly contended cache line using new refdst
infrastructure.
Note 1: loopback device excluded because of !IFF_XMIT_DST_RELEASE
Note 2: UDP packets dsts are built before ip_queue_xmit().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ip_route_input_noref() in ip fast path, to avoid two atomic ops per
incoming packet.
Note: loopback is excluded from this optimization in ip_rcv_finish()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input() is the version returning a refcounted dst, while
ip_route_input_noref() returns a non refcounted one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use low order bit of skb->_skb_dst to tell dst is not refcounted.
Change _skb_dst to _skb_refdst to make sure all uses are catched.
skb_dst() returns the dst, regardless of noref bit set or not, but
with a lockdep check to make sure a noref dst is not given if current
user is not rcu protected.
New skb_dst_set_noref() helper to set an notrefcounted dst on a skb.
(with lockdep check)
skb_dst_drop() drops a reference only if skb dst was refcounted.
skb_dst_force() helper is used to force a refcount on dst, when skb
is queued and not anymore RCU protected.
Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if
!IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in
sock_queue_rcv_skb(), in __nf_queue().
Use skb_dst_force() in dev_requeue_skb().
Note: dst_use_noref() still dirties dst, we might transform it
later to do one dirtying per jiffies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_SMP=y, then we own a queue spinlock, we can avoid the atomic
test_and_set_bit() from napi_schedule_prep().
We now have same number of atomic ops per netif_rx() calls than with
pre-RPS kernel.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
as addrlabels with an interface index are left alone when the
interface gets removed this results in addrlabels that can no
longer be removed.
Restrict validation of index to adding new addrlabels.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that cache_ioctl_procfs() calls the bkl explicitly, we need to
include the relevant header as well.
This fixes the following build error:
net/sunrpc/cache.c: In function 'cache_ioctl_procfs':
net/sunrpc/cache.c:1355: error: implicit declaration of function 'lock_kernel'
net/sunrpc/cache.c:1359: error: implicit declaration of function 'unlock_kernel'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Push down the bkl from procfs's ioctl main handler to its users.
Only three procfs users implement an ioctl (non unlocked) handler.
Turn them into unlocked_ioctl and push down the Devil inside.
v2: PDE(inode)->data doesn't need to be under bkl
v3: And don't forget to git-add the result
v4: Use wrappers to pushdown instead of an invasive and error prone
handlers surgery.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: John Kacur <jkacur@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Now we have a set of nested attributes:
IFLA_VFINFO_LIST (NESTED)
IFLA_VF_INFO (NESTED)
IFLA_VF_MAC
IFLA_VF_VLAN
IFLA_VF_TX_RATE
This allows a single set to operate on multiple attributes if desired.
Among other things, it means a dump can be replayed to set state.
The current interface has yet to be released, so this seems like
something to consider for 2.6.34.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
transport may be free before ICMP proto unreachable timer expire, so
we should delete active ICMP proto unreachable timer when transport
is going away.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan/macvlan start_xmit() can inform caller of congestion with
NET_XMIT_CN return value. This doesnt mean packet was dropped.
Increment normal stat counters instead of tx_dropped.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP-MD5 sessions have intermittent failures, when route cache is
invalidated. ip_queue_xmit() has to find a new route, calls
sk_setup_caps(sk, &rt->u.dst), destroying the
sk->sk_route_caps &= ~NETIF_F_GSO_MASK
that MD5 desperately try to make all over its way (from
tcp_transmit_skb() for example)
So we send few bad packets, and everything is fine when
tcp_transmit_skb() is called again for this socket.
Since ip_queue_xmit() is at a lower level than TCP-MD5, I chose to use a
socket field, sk_route_nocaps, containing bits to mask on sk_route_caps.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
