This patch extends the ncsi-netlink interface with two new commands and
three new attributes to configure multiple packages and/or channels at
once, and configure specific failover modes.
NCSI_CMD_SET_PACKAGE mask and NCSI_CMD_SET_CHANNEL_MASK set a whitelist
of packages or channels allowed to be configured with the
NCSI_ATTR_PACKAGE_MASK and NCSI_ATTR_CHANNEL_MASK attributes
respectively. If one of these whitelists is set only packages or
channels matching the whitelist are considered for the channel queue in
ncsi_choose_active_channel().
These commands may also use the NCSI_ATTR_MULTI_FLAG to signal that
multiple packages or channels may be configured simultaneously. NCSI
hardware arbitration (HWA) must be available in order to enable
multi-package mode. Multi-channel mode is always available.
If the NCSI_ATTR_CHANNEL_ID attribute is present in the
NCSI_CMD_SET_CHANNEL_MASK command the it sets the preferred channel as
with the NCSI_CMD_SET_INTERFACE command. The combination of preferred
channel and channel whitelist defines a primary channel and the allowed
failover channels.
If the NCSI_ATTR_MULTI_FLAG attribute is also present then the preferred
channel is configured for Tx/Rx and the other channels are enabled only
for Rx.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the NCSI driver is stopped with ncsi_stop_dev() the channel
monitors are stopped and the state set to "inactive". However the
channels are still configured and active from the perspective of the
network controller. We should suspend each active channel but in the
context of ncsi_stop_dev() the transmit queue has been or is about to be
stopped so we won't have time to do so.
Instead when ncsi_start_dev() is called if the NCSI topology has already
been probed then call ncsi_reset_dev() to suspend any channels that were
previously active. This resets the network controller to a known state,
provides an up to date view of channel link state, and makes sure that
mode flags such as NCSI_MODE_TX_ENABLE are properly reset.
In addition to ncsi_start_dev() use ncsi_reset_dev() in ncsi-netlink.c
to update the channel configuration more cleanly.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The concepts of a channel being 'active' and it having link are slightly
muddled in the NCSI driver. Tweak this slightly so that
NCSI_CHANNEL_ACTIVE represents a channel that has been configured and
enabled, and NCSI_CHANNEL_INACTIVE represents a de-configured channel.
This distinction is important because a channel can be 'active' but have
its link down; in this case the channel may still need to be configured
so that it may receive AEN link-state-change packets.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a package is deselected all channels of that package cease
communication. If there are other channels active on the package of the
suspended channel this will disable them as well, so only send a
deselect-package command if no other channels are active.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the NCSI driver sends a select-package command to all possible
packages simultaneously to discover what packages are available. However
at this stage in the probe process the driver does not know if
hardware arbitration is available: if it isn't then this process could
cause collisions on the RMII bus when packages try to respond.
Update the probe loop to probe each package one by one, and once
complete check if HWA is universally supported.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCSI hardware arbitration allows multiple packages to be enabled at once
and share the same wiring. If the NCSI driver recognises that HWA is
available it unconditionally enables all packages and channels; but that
is a configuration decision rather than something required by HWA.
Additionally the current implementation will not failover on link events
which can cause connectivity to be lost unless the interface is manually
bounced.
Retain basic HWA support but remove the separate configuration path to
enable all channels, leaving this to be handled by a later
implementation.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TCP_NLA_SRTT to SCM_TIMESTAMPING_OPT_STATS that reports the smoothed
round trip time in microseconds (tcp_sock.srtt_us >> 3).
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users to set and dump RED flags (ECN enabled and harddrop)
on per-virtual queue basis. Validation of attributes is split
from changes to make sure we won't have to undo previous operations
when we find out configuration is invalid.
The objective is to allow changing per-Qdisc parameters without
overwriting the per-vq configured flags.
Old user space will not pass the TCA_GRED_VQ_FLAGS attribute and
per-Qdisc flags will always get propagated to the virtual queues.
New user space which wants to make use of per-vq flags should set
per-Qdisc flags to 0 and then configure per-vq flags as it
sees fit. Once per-vq flags are set per-Qdisc flags can't be
changed to non-zero. Vice versa - if the per-Qdisc flags are
non-zero the TCA_GRED_VQ_FLAGS attribute has to either be omitted
or set to the same value as per-Qdisc flags.
Update per-Qdisc parameters:
per-Qdisc | per-VQ | result
0 | 0 | all vq flags updated
0 | non-0 | error (vq flags in use)
non-0 | 0 | -- impossible --
non-0 | non-0 | all vq flags updated
Update per-VQ state (flags parameter not specified):
no change to flags
Update per-VQ state (flags parameter set):
per-Qdisc | per-VQ | result
0 | any | per-vq flags updated
non-0 | 0 | -- impossible --
non-0 | non-0 | error (per-Qdisc flags in use)
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now ECN marking and HARD drop (the common RED flags) can only
be configured for the entire Qdisc. In preparation for per-vq flags
store the values in the virtual queue structure. Setting per-vq
flags will only be allowed when no flags are set for the entire Qdisc.
For the new flags we will also make sure undefined bits are 0.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all GRED's virtual queue data is dumped in a single
array in a single attribute. This makes it pretty much impossible
to add new fields. In order to expose more detailed stats add a
new set of attributes. We can now expose the 64 bit value of bytesin
and all the mark stats which were not part of the original design.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
32 bit counters for bytes are not really going to last long in modern
world. Make sch_gred count bytes on a 64 bit counter. It will still
get truncated during dump but follow up patch will add set of new
stat dump attributes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack messages to -EINVAL errors, to help users identify
their mistakes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case netlink wants to provide parsing error pass extack
to nla_parse_nested().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon want to add more code to the non-error path, separate
it from the error handling flow.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 60fb9567bf ("udp: implement complete book-keeping for
encap_needed") introduced a severe misuse of jump label APIs, which
syzbot, as reported by Eric, was able to exploit.
When multiple sockets/process can concurrently request (and than
disable) the udp encap, we need to track the activation counter with
*_inc()/*_dec() jump label variants, or we can experience bad things
at disable time.
Fixes: 60fb9567bf ("udp: implement complete book-keeping for encap_needed")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently on dequeue() ETF only drops the first expired packet, which
causes a problem if the next packet is already expired. When this
happens, the watchdog will be configured with a time in the past, fire
straight way and the packet will finally be dropped once the dequeue()
function of the qdisc is called again.
We can save quite a few cycles and improve the overall behavior of the
qdisc if we drop all expired packets if the next packet is expired.
This should allow ETF to recover faster from bad situations. But
packet drops are still a very serious warning that the requirements
imposed on the system aren't reasonable.
This was inspired by how the implementation of hrtimers use the
rb_tree inside the kernel.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a refactor that will simplify the implementation of the
next patch in this series which will drop all expired packets on the
dequeue flow.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETF's peek() operation is heavily used so use an rb_root_cached instead
and leverage rb_first_cached() which will run in O(1) instead of
O(log n).
Even if on 'timesortedlist_clear()' we could be using rb_erase(), we
choose to use rb_erase_cached(), because if in the future we allow
runtime changes to ETF parameters, and need to do a '_clear()', this
might cause some hard to debug issues.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in firing the qdisc watchdog if there are no future
skbs pending in the queue and the watchdog had been set previously.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we can use bpf or tcp tracepoint to conveniently trace the tcp
state transition at the run time.
So we don't need to do this stuff at the compile time anymore.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the vlan packet offloads are registered only upon 8021q module
load. However, even without this module loaded, the offloads could be
utilized, for example by openvswitch datapath. As reported by Michael,
that causes 2x to 5x performance improvement, depending on a testcase.
So move the vlan offload registrations into vlan_core and make this
available even without 8021q module loaded.
Reported-by: Michael Shteinbok <michaelsh86@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Michael Shteinbok <michaelsh86@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a missing indentation before the declaration of port. Add
it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace VLAN_TAG_PRESENT with single bit flag and free up
VLAN.CFI overload. Now VLAN.CFI is visible in networking stack
and can be passed around intact.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Bump version strings, by Simon Wunderlich
- Fixup includes, by Sven Eckelmann (3 patches)
- Separate BATMAN_ADV_DEBUG from DEBUGFS, by Sven Eckelmann
- Fixup tracing log documentation, by Sven Eckelmann
- Use exclusive locks to secure netlink information dump transfers,
by Sven Eckelmann (8 patches)
- Move CRC16 dependency, by Sven Eckelmann
- Enable MCAST by default, by Linus Luessing
-----BEGIN PGP SIGNATURE-----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=9x4D
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20181114' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- Bump version strings, by Simon Wunderlich
- Fixup includes, by Sven Eckelmann (3 patches)
- Separate BATMAN_ADV_DEBUG from DEBUGFS, by Sven Eckelmann
- Fixup tracing log documentation, by Sven Eckelmann
- Use exclusive locks to secure netlink information dump transfers,
by Sven Eckelmann (8 patches)
- Move CRC16 dependency, by Sven Eckelmann
- Enable MCAST by default, by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netperf udp stream shows that eth_type_trans takes certain cpu,
so adjust the mac address check order, and firstly check if it
is device address, and only check if it is multicast address
only if not the device address.
After this change:
To unicast, and skb dst mac is device mac, this is most of time
reduce a comparision
To unicast, and skb dst mac is not device mac, nothing change
To multicast, increase a comparision
Before:
1.03% [kernel] [k] eth_type_trans
After:
0.78% [kernel] [k] eth_type_trans
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if list is NULL pointer, and the following access of list
will trigger panic, which is same as BUG_ON
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support in tc flower for filtering based on port ranges.
Example:
1. Match on a port range:
-------------------------
$ tc filter add dev enp4s0 protocol ip parent ffff:\
prio 1 flower ip_proto tcp dst_port range 20-30 skip_hw\
action drop
$ tc -s filter show dev enp4s0 parent ffff:
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
ip_proto tcp
dst_port range 20-30
skip_hw
not_in_hw
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 85 sec used 3 sec
Action statistics:
Sent 460 bytes 10 pkt (dropped 10, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
2. Match on IP address and port range:
--------------------------------------
$ tc filter add dev enp4s0 protocol ip parent ffff:\
prio 1 flower dst_ip 192.168.1.1 ip_proto tcp dst_port range 100-200\
skip_hw action drop
$ tc -s filter show dev enp4s0 parent ffff:
filter protocol ip pref 1 flower chain 0 handle 0x2
eth_type ipv4
ip_proto tcp
dst_ip 192.168.1.1
dst_port range 100-200
skip_hw
not_in_hw
action order 1: gact action drop
random type none pass val 0
index 2 ref 1 bind 1 installed 58 sec used 2 sec
Action statistics:
Sent 920 bytes 20 pkt (dropped 20, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
v4:
1. Added condition before setting port key.
2. Organized setting and dumping port range keys into functions
and added validation of input range.
v3:
1. Moved new fields in UAPI enum to the end of enum.
2. Removed couple of empty lines.
v2:
Addressed Jiri's comments:
1. Added separate functions for dst and src comparisons.
2. Removed endpoint enum.
3. Added new bit TCA_FLOWER_FLAGS_RANGE to decide normal/range
lookup.
4. Cleaned up fl_lookup function.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netdev_rx_csum_fault() only shows a device name,
we need more information about the skb for debugging csum
failures.
Sample output:
ens3: hw csum failure
dev features: 0x0000000000014b89
skb len=84 data_len=0 pkt_type=0 gso_size=0 gso_type=0 nr_frags=0 ip_summed=0 csum=0 csum_complete_sw=0 csum_valid=0 csum_level=0
Note, I use pr_err() just to be consistent with the existing one.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RED qdisc's limit parameter changes the behaviour of the qdisc,
for instance if it's set to 0 qdisc will drop all the packets.
When replace operation happens and parameter is set to non-0
a new fifo qdisc will be instantiated and replace the old child
qdisc which will be destroyed.
Drivers need to know the parameter, even if they don't impose
the actual limit to be able to reliably reconstruct the Qdisc
hierarchy.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers offloading Qdiscs should have reasonable certainty
the offloaded behaviour matches the SW path. This is impossible
if the driver does not know about all Qdiscs or when Qdiscs move
and are reused. Send a graft notification from MQ.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers offloading Qdiscs should have reasonable certainty
the offloaded behaviour matches the SW path. This is impossible
if the driver does not know about all Qdiscs or when Qdiscs move
and are reused. Send a graft notification from RED. The drivers
are expected to simply stop offloading the Qdisc, if a non-standard
child is ever grafted onto it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers are currently not notified when a Qdisc is grafted as root.
This requires special casing Qdiscs added with parent = TC_H_ROOT in
the driver. Also there is no notification sent to the driver when
an existing Qdisc is grafted as root.
Add this very simple notifications, drivers should now be able to
track their Qdisc tree fully.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When socks' sk_reuseport is set, the same port and address are allowed
to be bound into these socks who have the same uid.
Note that the difference from sk_reuse is that it allows multiple socks
to listen on the same port and address.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a part of sk_reuseport support for sctp. It defines a helper
sctp_bind_addrs_check() to check if the bind_addrs in two socks are
matched. It will add sock_reuseport if they are completely matched,
and return err if they are partly matched, and alloc sock_reuseport
if all socks are not matched at all.
It will work until sk_reuseport support is added in
sctp_get_port_local() in the next patch.
v1->v2:
- use 'laddr->valid && laddr2->valid' check instead as Marcelo
pointed in sctp_bind_addrs_check().
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a part of sk_reuseport support for sctp, and it selects a
sock by the hashkey of lport, paddr and dport by default. It will
work until sk_reuseport support is added in sctp_get_port_local()
in the next patch.
v1->v2:
- define lport as __be16 instead of __be32 as Marcelo pointed in
__sctp_rcv_lookup_endpoint().
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to rigorous testing in wireless community mesh networks several
issues with multicast entries in the translation table were found and
fixed in the last 1.5 years. Now we see the first larger networks
(a few hundred nodes) with a batman-adv version with multicast
optimizations enabled arising, with no TT / multicast optimization
related issues so far.
Therefore it seems safe to enable multicast optimizations by default.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit ced72933a5 ("batman-adv: use CRC32C instead of CRC16 in TT
code") switched the translation table code from crc16 to crc32c. The
(optional) bridge loop avoidance code is the only user of this function.
batman-adv should only select CRC16 when it is actually using it.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Multiple datastructures use the hash helper functions to add and remove
entries from the simple hlist based hashes. These are often also dumped to
userspace via netlink and thus should have a generation sequence counter.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. And an external generation
sequence counter is introduced which tracks all modifications of the list.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. And an external generation
sequence counter is introduced which tracks all modifications of the list.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The debug messages of batman-adv are not printed to the kernel log at all
but can be stored (depending on the compile setting) in the tracing buffer
or the batadv specific log buffer. There is also no debug module parameter
but a batadv netdev specific log_level setting to enable/disable different
classes of debug messages at runtime.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The BATMAN_ADV_DEBUGFS portion of batman-adv is marked as deprecated. Thus
all required functionality should be available without it. The debug log
was already modified to also output via the kernel tracing function but
still retained its BATMAN_ADV_DEBUGFS functionality.
Separate the entry point for the debug log from the debugfs portions to
make it possible to build with BATMAN_ADV_DEBUG and without
BATMAN_ADV_DEBUGFS.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv_dbg trace event uses different functionality and datastructures
which are not directly associated with the trace infrastructure. It should
not be expected that the trace headers indirectly provide them and instead
include the required headers directly.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
