Here's a patch that adds MIDI support through USB for one of the Access
Music synths, the VirusTI.
The synth uses standard USBMIDI protocol on its USB interface 3, although
it does signal "vendor specific" class. A magic string has to be sent on
interface 3 to enable the sending of MIDI from the synth (this string was
found by sniffing usb communication of the Windows driver). This is all
my patch does, and it works on my computer.
Please note that the synth can also do standard usb audio I/O on its
interfaces 2&3, which already works with the current snd-usb-audio driver,
except for the audio input from the synth. I'm going to work on it when I
have some time.
Signed-off-by: Sebastien Alaiwan <sebastien.alaiwan@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> (cosmetics, list terminator)
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Extend the list of devices whose firmware does not expect more than one
USB MIDI packet in one USB packet.
bug report: https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3752
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
USB devices tends to represent dB ranges in different way than ALSA expects.
Add possibility to override these values and add guessed values for
SoundBlaster MP3+.
Also rename 'Capture Input Source' control to 'Capture Source' for
SoundBlaster MP3+ and Extigy.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The volume register is from 0..0x7f and 0..0x1a range is mute.
Also, fix mute combining in wm_vol_put(). The wrong behaviour was
noticed by Peter Christensen.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
After hours of debugging, I finally found the reason why some source
and runtime combination does not work. The PTP (page table pages)
address must be aligned. I am not sure how much, but alignment to
PAGE_SIZE is sufficient. Also, use ALSA's page allocation routines
to ensure proper virtual -> physical address translation.
Cc: <stable@kernel.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This is a cleanup for the dummy driver. The model kernel module parameter
is introduced to select the soundcard emulation.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow TLV blocks that do not have any values; the smallest possible TLV
is an empty container or one where the information is only in the tag.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Creating a control with TLV_COMMAND access was not possible because
snd_ctl_new1() forgot to include it in the mask of allowable access
bits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The code in pcm_lib updating runtime->hw_ptr_interrupt expects
that runtime->boundary is divisible with runtime->period_size.
Thanks are going to Clemens Ladisch for the notice.
Fix the runtime->boundary calculation using buffer_size * period_size
as base and find a least common multiple for 32bit platforms when
the expression might overflow.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clemens Ladisch noted for hw_ptr_removal in "cleanup & merge hw_ptr
update functions" commit:
"It is possible for the status/delay ioctls to be called when the sound
card's pointer register alreay shows a position at the beginning of the
new period, but immediately before the interrupt is actually executed.
(This happens regularly on a SMP machine with mplayer.) When that
happens, the code thinks that the position must be at least one period
ahead of the current position and drops an entire buffer of data."
Return back the hw_ptr_interrupt variable. The last interrupt pointer
is always computed from the latest hw_ptr instead of tracking it
separately (in this case all hw_ptr checks and modifications might
influence also hw_ptr_interrupt and it is difficult to keep it
consistent).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The SPDIF-input pin 0x1c is muted by default in hardware. Unmute appropriate
pin to get captured samples instead zeros. Tested on Lenovo Thinkstation.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This change fixes the "ALSA: pcm_lib - optimize wake_up() calls for PCM I/O"
commit. New sleeping queue is introduced to separate user space and kernel
space wake_ups. runtime->nowake is renamed to twake (transfer wake).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
As snd_seq_timer_set_tick_resolution() is always called with the same
three fields of struct snd_seq_timer, it suffices to give that as the
only parameter.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add the STMicroelectronics ST7597 codec and an unknown codec
from the same manufacturer found on the Creative SB 128 card (CT4810).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This model needs both 'Headphone Jack Sense' and 'Line Jack Sense' muted
for audible playback, so just add it to the ad1981 jack sense blacklist.
Cc: stable@kernel.org
Tested-by: Pete <x41215201@gmail.com>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The patch "sbawe: fix memory detection" fixed detection
for memoryless SB32 cards but broke detection of memory
above 512KB. This patch fixes the regression.
The patch has been tested on the SB32 card (CT3670) with
0MB, 2MB and 8MB memory installed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The problem is that in the original code sound_nblocks could go up to 1024
which would be an array overflow.
This was found with a static checker and has been compile tested only.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The XO's audio hardware is wired up to allow DC sensors (e.g. light
sensors, thermistors, etc) to be plugged in through the microphone jack.
Add sound mixer controls to allow this mode to be enabled and tweaked.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The XO-1.5 has a microphone LED designed to indicate to the user when
something is being recorded.
This light is controlled by the microphone bias voltage and it is
currently coming on all the time.
This patch defers the microphone port configuration until when recording
is actually taking place, fixing the behaviour of the LED.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added patch for Hewlett-Packard Company Device Subsystem id - 103c:30ea.
Signed-off-by: Ken Prox <kprox@users.sourceforge.net>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The WM9705 and WM9703 ops are the same actually so use
the same code for both.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When runtime->periods == 1 or when pointer crosses end of ring buffer,
the delta might be greater than buffer_size.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
As noted by pl bossart <bossart.nospam@gmail.com>, the PCM I/O routines
(snd_pcm_lib_write1, snd_pcm_lib_read1) should block wake_up() calls
until all samples are not processed.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Do general cleanup in snd_pcm_update_hw_ptr*() routines and merge them.
The main change is hw_ptr_interrupt variable removal to simplify code
logic. This variable can be computed directly from hw_ptr.
Ensure that updated hw_ptr is not lower than previous one (it was possible
with old code in some obscure situations when interrupt was delayed or
the lowlevel driver returns wrong ring buffer position value).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
In some debug cases, it might be usefull to see previous ring buffer
positions to determine position problems from the lowlevel drivers.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/kms: Fix &&/|| confusion in drm_fb_helper_connector_parse_command_line()
drm/edid: Fix CVT width/height decode
drm/edid: Skip empty CVT codepoints
drm: remove address mask param for drm_pci_alloc()
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
* korg/drm-radeon-next:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
The mask happens to be the same, but the IH is reading the status, not the
not the control register.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a NULL value is possible, the dereference should only occur after the
NULL test.
Coverity CID: 13338
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a NULL value is possible, the dereference should only occur after the
NULL test.
Coverity CID: 13335
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a NULL value is possible, the dereference should only occur after the
NULL test.
Coverity CID: 13334
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The encoder variable can be NULL in this function so I believe it should
be checked before dereference.
Coverity CID: 13253
[airlied: extremely unlikely to happen]
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Stanse found a memory leak in radeon_master_create. master_priv is not
freed/assigned on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (23 commits)
drm/i915: remove full registers dump debug
drm/i915: Add DP dpll limit on ironlake and use existing DPLL search function
drm/i915: Select the correct BPC for LVDS on Ironlake
drm/i915: Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake
drm/i915: Enable/disable the dithering for LVDS based on VBT setting
drm/i915: Permit pinning whilst the device is 'suspended'
drm/i915: Hold struct mutex whilst pinning power context bo.
drm/i915: fix unused var
drm/i915: Storage class should be before const qualifier
drm/i915: remove render reclock support
drm/i915: Fix RC6 suspend/resume
drm/i915: execbuf2 support
drm/i915: Reload hangcheck timer too for Ironlake
drm/i915: only enable hotplug for detected outputs
drm/i915: Track whether cursor needs physical address in intel_device_info
drm/i915: Implement IS_* macros using static tables
drm/i915: Move PCI IDs into i915 driver
drm/i915: Update LVDS connector status when receiving ACPI LID event
drm/i915: Add MALATA PC-81005 to ACPI LID quirk list
drm/i915: implement new pm ops for i915
...
The MMU code uses the copy_*_user_page() variants in access_process_vm()
rather than copy_*_user() as the former includes an icache flush. This
is important when doing things like setting software breakpoints with
gdb. So switch the NOMMU code over to do the same.
This patch makes the reasonable assumption that copy_from_user_page()
won't fail - which is probably fine, as we've checked the VMA from which
we're copying is usable, and the copy is not allowed to cross VMAs. The
one case where it might go wrong is if the VMA is a device rather than
RAM, and that device returns an error which - in which case rubbish will
be returned rather than EIO.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David McCullough <david_mccullough@mcafee.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When working with FDPIC, there are many shared mappings of read-only
code regions between applications (the C library, applet packages like
busybox, etc.), but the current do_mmap_pgoff() function will issue an
icache flush whenever a VMA is added to an MM instead of only doing it
when the map is initially created.
The flush can instead be done when a region is first mmapped PROT_EXEC.
Note that we may not rely on the first mapping of a region being
executable - it's possible for it to be PROT_READ only, so we have to
remember whether we've flushed the region or not, and then flush the
entire region when a bit of it is made executable.
However, this also affects the brk area. That will no longer be
executable. We can mprotect() it to PROT_EXEC on MPU-mode kernels, but
for NOMMU mode kernels, when it increases the brk allocation, making
sys_brk() flush the extra from the icache should suffice. The brk area
probably isn't used by NOMMU programs since the brk area can only use up
the leavings from the stack allocation, where the stack allocation is
larger than requested.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code will load the stack size and protection markings, but
then only use the markings in the MMU code path. The NOMMU code path
always passes PROT_EXEC to the mmap() call. While this doesn't matter
to most people whilst the code is running, it will cause a pointless
icache flush when starting every FDPIC application. Typically this
icache flush will be of a region on the order of 128KB in size, or may
be the entire icache, depending on the facilities available on the CPU.
In the case where the arch default behaviour seems to be desired
(EXSTACK_DEFAULT), we probe VM_STACK_FLAGS for VM_EXEC to determine
whether we should be setting PROT_EXEC or not.
For arches that support an MPU (Memory Protection Unit - an MMU without
the virtual mapping capability), setting PROT_EXEC or not will make an
important difference.
It should be noted that this change also affects the executability of
the brk region, since ELF-FDPIC has that share with the stack. However,
this is probably irrelevant as NOMMU programs aren't likely to use the
brk region, preferring instead allocation via mmap().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.33' of git://linux-nfs.org/~bfields/linux:
sunrpc: fix peername failed on closed listener
nfsd: make sure data is on disk before calling ->fsync
nfsd: fix "insecure" export option
There're some warnings of "nfsd: peername failed (err 107)!"
socket error -107 means Transport endpoint is not connected.
This warning message was outputed by svc_tcp_accept() [net/sunrpc/svcsock.c],
when kernel_getpeername returns -107. This means socket might be CLOSED.
And svc_tcp_accept was called by svc_recv() [net/sunrpc/svc_xprt.c]
if (test_bit(XPT_LISTENER, &xprt->xpt_flags)) {
<snip>
newxpt = xprt->xpt_ops->xpo_accept(xprt);
<snip>
So this might happen when xprt->xpt_flags has both XPT_LISTENER and XPT_CLOSE.
Let's take a look at commit b0401d72, this commit has moved the close
processing after do recvfrom method, but this commit also introduces this
warnings, if the xpt_flags has both XPT_LISTENER and XPT_CLOSED, we should
close it, not accpet then close.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Cc: J. Bruce Fields <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
