Add tmp105 sensor for droid 4. This can be used with modprobe
lm75.ko and running sensors from lm-sensors package. Note that
the lm75.c driver does not yet support alert interrupt but
droid 4 seems to be wired for it.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Droid 4 has a GPIO line that we can use with CONFIG_POWER_RESET_GPIO.
It is probably connected to the CPCAP PMIC, and seems to power down
the whole device taking power consumption to zero based on what
I measured.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TI LMU driver has not yet been merged, but the device
tree binding for TI LMU drivers has been acked already
earlier by Rob Herring <robh+dt@kernel.org>. So it should
be safe to apply to cut down the number of pending patches.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit enable DMA-based transfers for SD/eMMC card adapters
and reduce number of interrupts produced by SD-card/eMMC-card
adapters.
Sometimes interrupts from SD-card/eMMC-card adapters running in
PIO mode blocks execution of hrtimers and I2S DMA callbacks for
a long periods (100 ms or more).
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
[moved dma properties to rk3xxx.dtsi and added sdio dma]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The binding should state "cortina,gemini-gpio", "faraday,ftgpio010"
stating the full name of the IP part.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to [0] pointed out by Marc Zyngier in a report about a
similar error message, PPIs 11 and 13 are edge triggered on
Cortex-A9 socs including the rk3066 and rk3188 which currently
mark them as level triggered.
Until some time ago the gic did not care but commit 992345a58e
("irqchip/gic: WARN if setting the interrupt type for a PPI fails")
introduced a warning for that case.
Fix the warning on these socs by describing the interrupts correctly
and also using the binding constants for easier reading in the future.
[0] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0407f/CCHEIGIC.html
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The OPP are declared as shared but no operating points are declared for
cpu1, 2 and 3. Thus, the following error happens during the boot:
cpu cpu1: dev_pm_opp_of_get_sharing_cpus: Couldn't find tcpu_dev node.
This patch applies the operating points to each cpu of the A33.
Fixes: 03749eb88e ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cA1
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.12
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
* tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: dts: silk: Drop superfluous status update for frequency override
ARM: dts: alt: Drop superfluous status update for frequency override
ARM: dts: gose: Drop superfluous status update for frequency override
ARM: dts: porter: Drop superfluous status update for frequency override
ARM: dts: koelsch: Drop superfluous status updates for frequency overrides
ARM: dts: lager: Drop superfluous status update for frequency override
ARM: dts: marzen: Drop superfluous status update for frequency override
ARM: dts: bockw: Drop superfluous status update for frequency override
ARM: dts: porter: Always use status "okay" to enable devices
ARM: dts: r8a7793: Add INTC-SYS clock to device tree
ARM: dts: r8a7793: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7791: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Add INTC-SYS clock to device tree
ARM: dts: r8a7792: Add INTC-SYS clock to device tree
ARM: dts: r8a7791: Add INTC-SYS clock to device tree
ARM: dts: r8a7790: Add INTC-SYS clock to device tree
ARM: dts: r8a73a4: Add INTC-SYS clock to device tree
ARM: dts: r7s72100: Add watchdog timer
ARM: dts: r8a7790: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Remove unit-address and reg from integrated cache
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix USB host for sama5d2
- Fix cpuidle on sama5
-----BEGIN PGP SIGNATURE-----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=XXBm
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Fixes for 4.11:
- Fix USB host for sama5d2
- Fix cpuidle on sama5
* tag 'at91-ab-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: pm: cpu_idle: switch DDR to power-down mode
Revert "ARM: at91/dt: sama5d2: Use new compatible for ohci node"
Signed-off-by: Olof Johansson <olof@lixom.net>
A bunch of device tree fixes for various boards / SoCs.
-----BEGIN PGP SIGNATURE-----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=fo5j
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.11
A bunch of device tree fixes for various boards / SoCs.
* tag 'sunxi-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sun8i: a23/a33: drop bl_en_pin GPIO pinmux in reference design DTSI
ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settings
ARM: sun8i: Fix the mali clock rate
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix to reboot hang seen on imx6sx-udoo-neo board, by removing
arm-supply and soc-supply and using LDO enabled mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYz5T0AAoJEFBXWFqHsHzOiUwH/1S1b6Si8fbG0g11BQm+2N0u
mHf3Z41f+F81xuFFt/6ZX5ICiOXDlAdcga3QXUCNCWfYnFLJyDSoF6Z1JSUkGeEa
kVCmi+WWUOYtyU7QYfaBzPtZqqUurqwBu8WwOO/IW81yKpNMNflATKYreutki2oI
z3BW3WGlOEJXIJeyea3EjTClQLhP0qdEn08StneHUdA+YS9nd6/jreHhta4r7gQs
Z4B2yBap7P4a5glOzCafuIAdpPscKS096ND1k3APsiJPGaNjYtxhig5MGo89LK7e
JNfw1KroAmifGVmrgDVwKI3MFLrvSh74phFXwnIAX5iK2U2wB/fiMQjVKmvY9tw=
=NSw6
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.11:
- A fix to reboot hang seen on imx6sx-udoo-neo board, by removing
arm-supply and soc-supply and using LDO enabled mode.
* tag 'imx-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx-udoo-neo: Fix reboot hang
Signed-off-by: Olof Johansson <olof@lixom.net>
The moxart interrupt line flags were not respected in previous
driver: instead of assigning them per-consumer, a fixes mask
was set in the controller.
With the migration to a standard Faraday driver we need to
set up and handle the consumer flags correctly. Also remove
the Moxart-specific flags when switching to using real consumer
flags.
Extend the register window to 0x100 bytes as we may have a few
more registers in there and it doesn't hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Allow including of dtsi files in an architecture-independent manner.
Some dtsi files may be shared between architectures and one suggestion
was to have symlinks and let these includes get accessed via a
#include <arm64/foo.dtsi>
So add the necessary symlinks for arm32.
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. The interrupt has to be cleared, because otherwise
system enters infinite interrupt handling loop.
Use a samsung,s3c6410-wdt compatible to select appropriate quirk for
clearing the watchdog interrupt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. The interrupt has to be cleared, because otherwise
system enters infinite interrupt handling loop.
Use a samsung,s3c6410-wdt compatible to select appropriate quirk for
clearing the watchdog interrupt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. The interrupt has to be cleared, because otherwise
system enters infinite interrupt handling loop.
Use a samsung,s3c6410-wdt compatible to select appropriate quirk for
clearing the watchdog interrupt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The highest supported frequency (1.2GHz) requires to "overvolt" the CPU.
However, some boards still do not have the cpu-supply DT property in the
cpu DT node which means that the CPU will always run with the same input
voltage but try to run at 1.2GHz frequency. This is the source of
(experienced) CPU crashes.
Remove the OPP which requires overvolting the CPU until all boards have
a cpu-supply property.
Fixes: 03749eb88e ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The digital AIF interfaces has been renamed in the sun8i audio codec
driver so the audio-routing in the device tree must be renamed too.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that all resets added match the corresponding module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that all resets added match the corresponding module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The bl_en_pin GPIO pinmux is configured as "gpio_in", which makes it
conflicts with the real GPIO usage (out), and makes the backlight not
usable.
Drop the GPIO pinmux for it, thus this GPIO can be correctly used.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPU port of the BCM53125 is configured with RGMII (no delays) but
this should actually be RGMII with transmit delay (rgmii-txid) because
STMMAC takes care of inserting the transmitter delay. This fixes
occasional packet loss encountered.
Fixes: d7b9eaff5f ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the Gemini power controller to the SoC DTSI
file.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds crypto hardware (SPU) to Northstar Plus device tree file.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adds mailbox / PDC to NSP device tree. Needs new compatibility string
to differentiate from NS2 version.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adding ethernet aliases. These are used, for example, by bootloaders,
to modify the MAC addresses in the device tree.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This is BCM47081A0 based home router with BCM43217 and BCM4352 wireless
chipsets.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c device tree entry should be disabled by default to match the
current convention in other device tree files. Similarily, enable it on
the XMC board, where it is being used.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the EHCI and OHCI entries to the Northstar Plus device tree files.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add I2C support to the bcm5301x Device Tree. Since no driver changes
are needed to enable this hardware, only the device tree changes are
required to make this functional.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for the ARM TWD Watchdog to the bcm5301x device tree. The
ARM TWD timer allocated the register space for the WDT, so this patch
necessitated shrinking that. Also, the GIC masks were added for these.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add OneNAND node for IGEP and leave it disabled by default. It is up
to bootloader to enable proper node. Timing just works, but values are
copied over from N900 as I was unable to find chip datasheet.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Note that early-bresp-disable and full-line-zero-disable are required
because the sideband signals between the CPU and L2C were not connected
in this SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the dmas and dma-names properties to support HDMI audio.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the Altera Arria10 System Resource Reset Controller to the MFD
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2 change commit header to ARM: dts: socfpga.
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3228/rk3229.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3066/rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3036.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3288.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
The best place to register the CPU cooling device is from the cpufreq
driver as we would know if all the resources are already available or
not. That's what is done for the cpufreq-dt.c driver as well.
The cpu-cooling driver for dbx500 platform was just (un)registering
with the thermal framework and that can be handled easily by the cpufreq
driver as well and in proper sequence as well.
Get rid of the cooling driver and its its users and manage everything
from the cpufreq driver instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix smartreflex platform data regression where I accidentally
removed legacy platform data still in use
- Fix hypervisor mode for thumb2 kernel
- Fix misplaced tpic2810 to move it to right bus
- Enable INPUT_MOUSEDEV as a loadable module have mice working
- Fix use of gpio-key,wakeup and use wakeup-source instead as
this accidentally sneaked in during the merge window
- Fix error handling for onenand to properly return error
- Remove legacy gpmc-nand.c that's now dead code, this
also removes dependency to the MTD tree for further driver
changes
- Fix device node reference count errors for omap3 and
related to it also release device nodes after no longer
needed
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAli9kKQRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXMHMQ/+LO3aeN9AYuBhKulGt09NRktUw5x8/lbx
MiHwKviGP+eUsfBZ4e6Lv2N2s6bKwf0fdWT9HDlsWVPQorl/ZqihNlbwcVgWaBwZ
5Zw3beVjZCZ0rNQSQ1nKDmFIEN0S5+neTQdJhk+BMH+20r+D2thEQwXHoEEoAJSN
KJVL3a1TEgcaKT+WuFv2fPx+FxFd3OoAkNaxBJKUN8GhRBJLkq89Z+x7ZSnOBAhP
SYtJ3m7BCHi1CS0EHmzTsbFtsc4AUV3EN+3dIfyvRY4BWIEa60oKKiidYheSzYiF
LNDHA2QDuvHD5oB7bB6jSlloFDZG0udt50lkrm+LxDj5FIO7BvRE87ql/YZYPpOX
sojnVVXGngAweqU9ZogYZ0w2Dhp5RVBsEv40H77TLL0O4o6b5b3fj4fjbI5ObCqD
eVW5VQjPQJ7MbC+F1IUz2bM2mIGHiVTYd8p0G83o5Xyso8M9GY0fyjMuehaBvOw+
1j17MMFTM3zjQ1MSHkSszUwrKVpWwyrHssbWxFE2m1ZmBV9nPtVD3fkXxA5uQ4R8
dK5OJ86IZfPOe+v5bnXSFGtfYL2x5xuEhbCEdfgJ3tYcL33EzkAVciP36teLmkKP
1kTYdD2/LxORVXG6bf+RBWdaaaifRvVZZdKF1Bxz0NH4xWyedV0W+1wMGWqe6uBa
0Km3BWEY05k=
=svZk
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/fixes-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.11-rc cycle:
- Fix smartreflex platform data regression where I accidentally
removed legacy platform data still in use
- Fix hypervisor mode for thumb2 kernel
- Fix misplaced tpic2810 to move it to right bus
- Enable INPUT_MOUSEDEV as a loadable module have mice working
- Fix use of gpio-key,wakeup and use wakeup-source instead as
this accidentally sneaked in during the merge window
- Fix error handling for onenand to properly return error
- Remove legacy gpmc-nand.c that's now dead code, this
also removes dependency to the MTD tree for further driver
changes
- Fix device node reference count errors for omap3 and
related to it also release device nodes after no longer
needed
* tag 'omap-for-v4.11/fixes-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Release device node after it is no longer needed.
ARM: OMAP2+: Fix device node reference counts
ARM: OMAP2+: Remove legacy gpmc-nand.c
ARM: OMAP2+: gpmc-onenand: propagate error on initialization failure
ARM: dts: am335x-pcm953: Fix legacy wakeup source binding
ARM: omap2plus_defconfig: Enable INPUT_MOUSEDEV as loadable modules
ARM: dts: am57xx-idk: tpic2810 is on I2C bus, not SPI
ARM: OMAP5 / DRA7: Fix HYP mode boot for thumb2 build
ARM: OMAP3: Fix smartreflex platform data regression
Signed-off-by: Olof Johansson <olof@lixom.net>
please pull the following:
- Jon fixes the UART output on the Broadcom bcm953012k reference board by
using the proper clock reference instead of hard-coding the baud rate
- Jon also fixes the memory map on the bcm953012k reference board by using
the appropriate physical RAM start address
- Jon finally fixes the interrupt type for the Cortex A9 global and local
timers found in the BCM5301X SoC (Norsthar).
-----BEGIN PGP SIGNATURE-----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=0Qzy
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.11/devicetree-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for 4.11,
please pull the following:
- Jon fixes the UART output on the Broadcom bcm953012k reference board by
using the proper clock reference instead of hard-coding the baud rate
- Jon also fixes the memory map on the bcm953012k reference board by using
the appropriate physical RAM start address
- Jon finally fixes the interrupt type for the Cortex A9 global and local
timers found in the BCM5301X SoC (Norsthar).
* tag 'arm-soc/for-4.11/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the AB8500 clocks to the device tree using the new
bindings from the clk subsystem, making audio work again.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Watchdog module does not have external dependencies so it can be safely
enabled in exynos4.dtsi thus making it available for all Exynos4-based
boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Watchdog module does not have external dependencies so it can be safely
enabled in s3c64xx.dtsi thus making it available for all S3C64xx-based
boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
The Exynos4412 has the same watchdog as newer SoCs (e.g. Exynos5250).
Just like the others, for working it requires additional steps in Power
Management Unit: unmasking the reset request and enabling the system
reset. Without these additional steps in PMU, the watchdog will not be
able to reset the system on expiration event.
Change the compatible of Exynos4412 watchdog device node to
samsung,exynos5250-wdt which includes the additional PMU steps.
This will also fix infinite watchdog interrupt in soft mode (lack of
interrupt clear) because it is also included in samsung,exynos5250-wdt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7793.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The pcie_bus_clk device node is already enabled in r8a7791.dtsi, so
there is no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk and pcie_bus_clk device nodes are already enabled in
r8a7791.dtsi, so there is no need to update their statuses again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7790.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7779.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7778.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While status "ok" does work, the canonical form is "okay", so update the
few places that used the former.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-wbd222.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-wbd111.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-rut1xx.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-nas4220b.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference &gpio1.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a device tree for the Gemini SoC and the ITian
Square One SQ201 board that has been my testing target
for Gemini device tree support.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The eMMC devices on UniPhier boards are generally used in the 8-bit
mode. So, DAT4-7 pins should be controlled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These UniPhier DT files are fine as long as they are compiled in the
Linux build system. It is true that Linux is the biggest user of
DT, but DT is project neutral from its concept. DT files are often
re-used for other projects. Especially for the UniPhier platform,
these DT files are re-used for U-Boot as well.
If I feed these DT files to the FDTGREP tool in U-Boot, it complains
about the node order.
FDTGREP spl/u-boot-spl.dtb
Error at 'fdt_find_regions': FDT_ERR_BADLAYOUT
/aliases node must come before all other nodes
Given that DT is not very sensitive to the order of nodes, this is a
problem of FDTGREP. I filed a bug report a year ago, but it has not
been fixed yet.
Differentiating DT is painful. So, I am up-streaming the requirement
from the down-stream project.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock and the C4 power domain,
so it can be power managed using that clock in the future.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add watchdog timer support for RZ/A1.
For the RZ/A1, the only way to do a reset is to overflow the WDT, so this
is useful even if you don't need the watchdog functionality.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Such a trigger doesn't exist in Linux and is not needed as LED is being
turned off by default. This could cause errors in LEDs core code when
trying to set default trigger.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Such a trigger doesn't exist in Linux and is not needed as LED is being
turned off by default. This could cause errors in LEDs core code when
trying to set default trigger.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch updates the Duckbill device tree and synchronize it with
the vendor distributed file. The changes in mostly pin-muxing stuff,
but also some minor fixes. In detail:
- enable SPI pins
- enable I2C pins
- enable UART pins
- enable LRADC pin
- adjust USB DR mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
According to phy datasheet, 25ms are sufficient. This also reduces
the time to boot the system.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch renames mmc2_sck_cfg in order to prepare for an alternative
muxing setup.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Quoting Philipp Zabel:
"Since this regulator is used as the TVDAC analog power supply, this
range should at least be limited to the analog power supply range of the
TVDAC, listed in Table 74-9. of the i.MX53 reference manual (2.5-2.75V).
But since the nominal voltage is 2.75V, which was used to determine the
analog gain that is supposed to result in the necessary 0.7V
peak-to-peak amplitude on the VGA output, I'd say we should just fix the
voltage to 2750000 here."
, so limit the TVDAC analog power supply as suggested.
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cm-fx6 module has an onboard Wolfson wm8731 codec which is muxed
to the ssi2 controller. Unlike most (all?) supported i.MX6 board/codec
combinations the wm8731 is operated in slave mode and the clock setup
is static.
Add support for it.
Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
[christopher.spinrath@rwth-aachen.de: enhanced commit message, ported
to upstream and some cleanup]
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After issuing a 'reboot' command the imx6sx-udoo-neo board does not
reboot as expected and it just hangs instead.
In mainline kernel only LDO enabled mode is supported. Do not provide
arm-supply/soc-supply nodes in the device tree, so that the board operates
in LDO enabled mode and can then successfully reboot via watchdog.
Fixes: 76e691fc76 ("ARM: dts: imx6sx: Add UDOO Neo support")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Marvell 98dx3236 SoC only has a single PCIe x1 interface. The "Port
0.1 MEM" range was errantly kept when creating a specific dts for the
SoC.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Previously the coreclk binding for the 98dx3236 SoC was inherited from
the armada-370/xp. This block is present in as much as it is possible to
read from the register location without causing any harm. However the
actual sampled at reset values are reflected in the DFX block.
Moving the binding to the DFX block enables support for different clock
strapping options in hardware.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Marvell datasheets refer to the integrated CPU as "Armada-XP". In
reality there are a number of differences to the actual Armada-XP so
rather than including armada-xp.dtsi and disabling many of the IP
blocks. Include armada-370-xp.dtsi and add the required nodes.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Rather than having a separate node for the dfx server add a reg property
to the parent node. This give some compatibility with the Marvell
supplied SDK.
As no upstream driver currently exists for this block and support for
this SoC is still quite fresh in the kernel it should not be necessary
to retain a backwards compatible binding.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In others board we have the sata led set to function
with the sata led trigger by default.
This patch makes the same for these board that have sata
led but get disabled by not associating it to any trigger.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The mbus binding had been extended more than two years ago, but the
device tree files for Armada 38x didn't change.
Adding this third entry will allow the mbus going to suspend which was
the last thing preventing the SoC going to standby mode
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Linksys WRT1900ACS (Shelby) is another Armada 385 based router in
the Linksys WRT AC Series which got released in October 2015.
The file armada-385-linksys-shelby.dts is taken from OpenWrt as-is and
originally authored by Imre Kaloz.
URL: 8466384db1/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-linksys-shelby.dts
CC: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the burst and esc clock frequency properties to the parent (DSI node).
Currently the clock is parsed from the port node, while it should be
taken from the dsi node.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In Odroid XU3 Lite board, the temperature levels reported for thermal
zone 0 were weird. In warm room:
/sys/class/thermal/thermal_zone0/temp:32000
/sys/class/thermal/thermal_zone1/temp:51000
/sys/class/thermal/thermal_zone2/temp:55000
/sys/class/thermal/thermal_zone3/temp:54000
/sys/class/thermal/thermal_zone4/temp:51000
Sometimes after booting the value was even equal to ambient temperature
which is highly unlikely to be a real temperature of sensor in SoC.
The thermal sensor's calibration (trimming) is based on fused values.
In case of the board above, the fused values are: 35, 52, 43, 58 and 43
(corresponding to each TMU device). However driver defined a minimum value
for fused data as 40 and for smaller values it was using a hard-coded 55
instead. This lead to mapping data from sensor to wrong temperatures
for thermal zone 0.
Various vendor 3.10 trees (Hardkernel's based on Samsung LSI, Artik 10)
do not impose any limits on fused values. Since we do not have any
knowledge about these limits, use 0 as a minimum accepted fused value.
This should essentially allow accepting any reasonable fused value thus
behaving like vendor driver.
The exynos5420-tmu-sensor-conf.dtsi is copied directly from existing
exynos4412 with one change - the samsung,tmu_min_efuse_value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Add pcie-phy node to phy-exynos-pcie along with some changes to other
nodes:
1. Remove the configuration space from "ranges" property because this
was the old way of getting it. Preferred is to use "config" reg.
2. Use the reg-names as "elbi" and "config" so the purpose of addresses
will be easily known.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This commit adds the device tree description for the Synology DS116 NAS.
It is a one-bay NAS powered by a Marvell Armada 385 at 1.866 GHz. The
device features the following items :
- 1 GB DDR3 RAM
- a 8MB SPI flash
- 2 USB3 ports, power-controlled via a GPIO for each
- 1 gigabit ethernet interface connected over SGMII to a 88e1514 phy
- a single SATA port, power-controlled via a GPIO
- a battery-powered RTC
- one UART connected to the serial console (2mm connector on board)
- the Tx line of the second UART connected to a PIC microcontroller
dealing with beep, reset, power-off and LED blinking (9600 Bps)
- some of the front-panel LEDs are connected to GPIOs, one is directly
connected to the SATA link to report disk activity.
- a GPIO-controlled fan (3 bits for 7 speeds and OFF)
With this DTS, my NAS is 100% functional starting with kernel 4.9.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As was done with Armada XP, add node labels to Armada 38x common and SoC
specific nodes to make them easier to reference in board device trees.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Leave pca953x P06,P07 pins on b850v3 platform and P06 pin on
b450v3/b650v3 unconfigured in the kernel space since they could be
configured as DP1_RST and DP2_RST by the applications for the DP FW
update support.
Signed-off-by: Ken Lin <ken.lin@advantech.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Extend the vpif node with an output port with a single channel.
NOTE: this is still mostly just hardware description - the actual
driver is registered using pdata-quirks. We need the node however
for correct pin control function selection.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We need the expander to be probed to allow the VPIF controller to
receive interrupts from the video decoder.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a new pinctrl sub-node for vpif display pins. Move VP_CLKIN3 and
VP_CLKIN2 to the display node where they actually belong (vide section
36.2.2 of the OMAP-L138 technical reference manual).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The da850-evm dts file contains whitespace errors in the vpif node.
This patch fixes them.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds a device tree node for sound on LEGO MINDSTORMS EV3. The EV3
uses one of the SoC PWMs connected to an amplifier to create sound from
a speaker.
The PWM is passed through a low-pass filter, so it is actually possible
to do PCM playback, but there is no existing driver, so just using
pwm-beeper for now, since it is also a compatible mode of operation.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds a node for the TI ADS7957 analog/digital converter on LEGO
MINDSTORMS EV3 as well as a regulator node that is used by the A/DC node.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A7 cache controller is an integrated controller, and thus the
device node representing it should not have a unit-addresses or reg
property.
Fixes: 34ea4b4a82 ("ARM: dts: r8a7794: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: ad53f5f00b ("ARM: dts: r8a7793: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 7c4163aae3 ("ARM: dts: r8a7792: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 6f9314ce25 ("ARM: dts: r8a7791: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15/A7 cache controllers are integrated controllers, and thus
the device nodes representing them should not have unit-addresses or reg
properties.
Fixes: 2c3de36700 ("ARM: dts: r8a7790: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A7 cache controller is an integrated controller, and thus the
device node representing it should not have a unit-addresses or reg
property.
Fixes: c95360247b ("ARM: dts: r8a7745: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 34e8d993a6 ("ARM: dts: r8a7743: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15/A7 cache controllers are integrated controllers, and thus
the device nodes representing them should not have unit-addresses or reg
properties.
Fixes: b0da45c60d ("ARM: dts: r8a73a4: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The dual Cortex-A9 MPCore inside socfpga has a standard PMU unit for
each core mapped in the DAP memory space. Add support for it!
Tested with perf on a Cyclone 5 SoC DK.
Reported-by: Alberto Dassatti <alberto.dassatti@heig-vd.ch>
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Tested-by: Alberto Dassatti <alberto.dassatti@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This makes it easier to reference the CPU nodes afterwards.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The skeleton.dtsi file is now deprecated as noted in commit 9c0da3cc61
("ARM: dts: explicitly mark skeleton.dtsi as deprecated"). The SoCFPGA
device trees already contain the nodes that are defined in skeleton.dtsi
(#address-cells, #size-cells, chosen, aliases, memory).
Including skeleton.dtsi is useless and will produce the following
warning when compiled with W=1:
Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
GPIO LEDs in the Cyclone5 EBV SOCrates board have a unit name but no reg
property. Indeed, GPIO LEDs do not need such a property. They do not
need a unit name neither. This will trigger the following warnings when
compiled with W=1:
Node /gpio-leds/led@0 has a unit name, but no reg property
Node /gpio-leds/led@1 has a unit name, but no reg property
Node /gpio-leds/led@2 has a unit name, but no reg property
The solution is to remove the unit name. In order to have unique node
names, a rename is necessary. This should be harmless as all the LEDs
have a 'label' property, hence their name do not derive from the node
name and will stay the same after this patch.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The stmpe_touchscreen node in Cyclone5 MCV EVK has a reg property, but
this is not used by the driver. Moreover the binding documentation do
not define this property. Having a reg property without a unit name will
trigger the following warning when compiled with W=1:
Node /soc/i2c@ffc04000/stmpe811@41/stmpe_touchscreen has a reg or ranges
property, but no unit name
Remove the superfluous reg property.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Node eccmgr has a unit name, but do not have a reg property as only the
child nodes do have this property. Likewise the usbphy node do not have
a reg property. This will trigger the following warnings when compiled
with W=1:
Node /soc/eccmgr@ffd08140 has a unit name, but no reg property
Node /soc/usbphy@0 has a unit name, but no reg property
Remove the superfluous unit names.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Memory nodes in Arria5, Cyclone5 and Arria10 do not have a unit name.
This will trigger several warnings like this one (when compiled with
W=1):
Node /memory has a reg or ranges property, but no unit name
Add the corresponding unit name to each node.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Most clock nodes in Arria5, Cyclone5 and Arria10 have a reg property but
does not have a unit name. This will trigger several warnings like this
one (when compiled with W=1):
Node /soc/clkmgr@ffd04000/clocks/periph_pll has a reg or ranges
property, but no unit name
Add the corresponding unit name to each node.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Fix warnings reported when built with W=1:
Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") declared that skeleton.dtsi was deprecated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Added two WAN status LEDs and a GPIO key for brightness which were
missing.
Signed-off-by: Aditya Xavier <adityaxavier@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's preferred to have DT source files licensed under BSD compatible
license. All new BCM5301X DTS files use ISC so let's also relicense old
ones to it.
Except for me only Hauke was ever touched these files in his commit
9faa5960ee ("ARM: BCM5301X: add NAND flash chip description") and
commit bb1d8fba19 ("ARM: BCM5301X: add NAND flash chip description for
Asus RT-AC87U").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The modules stay disabled by default, and if you want to enable DSI
you'll need an overlay that connects a panel to it.
Signed-off-by: Eric Anholt <eric@anholt.net>
Droid4's touchscreen can be used with mainline's maxtouch driver. The
touchscreen's lower area is used for four soft buttons (KEY_MENU,
KEY_HOME, KEY_BACK, KEY_SEARCH), but that does not seem to be currently
supported by the mainline kernel.
The mxt224 configuration can be saved with "mxt-app" for the kernel
to load. It can be saved after the first boot with:
# mxt-app -d i2c-dev:1-004a --save /lib/firmware/maxtouch.cfg
Where the mxt-app can be found at:
https://github.com/atmel-maxtouch/mxt-app
The firmware for the droid 4 mxt224 comes with GPLv2 license in the
Motorola Linux kernel sources. This firmware can be dumped out with
"droid4-touchscreen-firmware" program at:
https://github.com/tmlind/droid4-touchscreen-firmware
The related LCD patches are still pending, but when merged,
the touchscreen can be rotated in X with something like:
# xrandr --output DSI-1 --rotate right
# xinput set-prop 6 'Coordinate Transformation Matrix' \
0 1 0 -1 0 1 0 0 1
For now, we rely on a gpio-hog but later on we can add the reset
gpio handling to the driver and have it load the maxtouch.cfg and
maxtouch.fw on boot.
This patch is based on combined similar patches done by me and
Sebastian.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Droid 4 "Volume Down" and "Keypad Slide" keys are
connected via SoC GPIOs, "Power Key" via CPCAP and
all other keys via SoC keypad Matrix. This adds the
GPIO keys.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[tony@atomide.com: updated to apply on omap4-keypad patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With drivers/mfd/motorola-cpcap.c and drivers/regulator/cpcap-regulator.c
we can now configure proper regulators for droid 4.
Let's add regulator voltages and switch over MMC, eMMC and WLAN to use
the CPCAP regulators.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some SPI nodes are missing #address-cells and #size-cells. This is
causing warning at device tree compilation when some SPI device
sub-nodes are defined.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Commit 9b5ba0df4e ("ARM: shmobile: Introduce ARCH_RENESAS") started
the migration from ARCH_SHMOBILE_MULTI to ARCH_RENESAS.
Update the Makefile to build DTBs for Renesas platforms to use the new
symbol, and move the Renesas section to preserve sort order.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SDHI controller in the RZ/A1 has 2 clock sources per channel and both
need to be enabled/disabled for proper operation. This fixes the fact that
the define for R7S72100_CLK_SDHI1 was not correct to begin with (typo), and
that all 4 clock sources need to be defined an used.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Mali clock rate was improperly assumed to be 408MHz, while it was
really 384Mhz, 408MHz being the "extreme" frequency, and definitely not
stable.
Switch for the stable, correct frequency for the GPU.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mali GPU in the A33 has various operating frequencies used in the
Allwinner BSP.
Add them to our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the needed node for DFVS on Sinovoip BPI-M2.
This add the axp221 under the p2wi node, the regulators and
the cpu-supply property for cpu0.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Beelink X2 has an on-board eMMC so add a node enabling
the mmc2 controller.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20-OLinuXino-Micro has 3.5 mm sockets for headphone output and
microphone input.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the GR8 DTSI is duplicated with the common sun5i DTSI, and some of
the extra nodes defined there actually apply to all of the sun5i family.
Move those into the common DTSI so that all SoCs can benefit from it, and
include the sun5i DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some controllers found in the R8 DTSI actually apply to all of the sun5i
family. Move those into the common DTSI so that all SoCs can benefit from
it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some controllers found in the A10s DTSI actually apply to all of the sun5i
family. Move those into the common DTSI so that all SoCs can benefit from
it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some controllers found in the A13 DTSI actually apply to all of the sun5i
family. Move those into the common DTSI so that all SoCs can benefit from
it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UART3 pin group for the CTS and RTS signals doesn't follow our usual
pattern. Rename it so that it matches.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There's one UART2 pin group that can be used across all sun5i SoCs.
However, the A10s already has one pin group for that controller.
Change the index of the one in the A10s DTSI, and add the common one to
sun5i.dtsi
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Of the three simple framebuffer setups we have in the A10s, two of them can
be shared with the other SoCs from the sun5i family (LCD panel and
composite output).
However, the only one we cannot share is the HDMI, which is the first
listed in the A10s DTSI. In order to make it more logical and so that we
can share the framebuffer nodes in the common DTSI, reorder those nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
One of the pins group for the EMAC can be used by all the SoCs of the sun5i
family, and as such can be moved to the common DTSI.
Unfortunately, this group is the second one we declare in our DT for now.
Make it the first one so that it's more logical and consistent with the
rest of our DTs before moving it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Let's configure the keypad in a way where it's usable out of the
box for Linux console use. We want to have the keyboard usable with
Linux console for example when stuck into an initramfs during boot,
for when installing a distro.
As we need to need to have keys mapped in the user space anyways
for some of the keys to match the labels, this non-standard mapping
or usability should be OK.
Some keys don't match the labels either as they don't follow the PC
keyboard style. For example we have "shift + ," produce "<", and
"shift + ." produce ">" instead of ";" and ":".
So let's follow the standard PC keyboard layout for ctrl, shift and
alt keys:
Ctrl = what is labeled as shift
Alt = what is labeled as SYM
Shift = what is lableled as caps lock
This way we have Ctrl key for console use. Who knows where they got
the caps lock idea.. Probably from some focus group popularity vote
or something.
For the OK key, let's keep it as the useless KEY_OK unless we can
come up with some standard mapping for it we can stick with.
We have at least Esc, Delete, Meta, and Page Down keys missing, but
none of them seem to be better than others. PC keyboard often has
Page Down in that location. Esc would be probably the most usable
one when installing a Linux distro but is the opposite of OK.
Note that the LCD keys are just touchscreen hot spots, so I'm not
sure if the driver or hardware allows setting them up as keys for
the console.
Anyways, the rest can be mapped in the user space.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch add basic support for RK3288-Tinker board. We can boot in to rootfs
with this patch.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The MiQi board's green LED doesn't work at all with the mainline kernel.
There are multiple reasons to this. First, the gpio number is wrong, it
is declared on gpio220 (chip 7 pin 4) instead of gpio218 (chip 7 pin 2).
Second, a pinctrl is referenced, also declared with the same wrong value
while it is not unused. Third, the GPIO polarity was wrong (active low
instead of active high) with the default value set to "default-on",
resulting in the LED being turned off even when the GPIO is correct.
This patch fixes all these inconsistencies at once since these they are
related to each other, and also restores the "timer" trigger which is
the same as the one used by the kernels shipped with the board.
It's important to note that during the port to mainline, the led's label
was changed from "System" to "miqi:green:user", so scripts making use of
the name will still not work until they're fixed.
Fixes: b1a76f75d76e ("ARM: dts: rockchip: add MiQi board from mqmaker")
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit adds the DT definition of the es8388 i2c device
found at address 0x10. It also adds the definition for connecting
the Rockchip I2S to the es8388 analog output.
This commit is based on the initial work that was done by Sjoerd Simons
<sjoerd.simons@collabora.com> with some improvements.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Memory starts at 0x80000000, not 0. 0 "works" due to mirrior of the
first 128M of RAM to that address. Anything greater than 128M will
quickly find nothing there. Correcting the starting address has
everything working again.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: 7eb05f6d ("ARM: dts: bcm5301x: Add BCM SVK DT files")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The UARTs are outputting garbage on the console. This is due to a speed
issue. We can simply use the clock speed (which is now defined in the
DTSI file) and everything works fine.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: cdc36b22 ("ARM: dts: enable clock support for BCM5301X")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's connected to a GPIO pin of an extra controller placed on the PCIe
card.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tenda AC9 has PCIe controller with just one device connected to it:
0000:00:00.0 14e4:d145 Bridge Device
└─ 0000:01:00.0 14e4:a8db Network Controller
This card is directly on SoC (doesn't use physical connector) and has
BCM43217 chipset with bcma bus. One of its components is ChipCommon core
which is also a GPIO controller. We need to describe it to be able to
add devices using its GPIO pins.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Initial version of DTS to support Broadcom BCM953012HR Northstar
HR platform, similar to, but not the same as existing 953012K.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It
uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The iproc-qspi driver is the SPI driver that should be used going
forward. Modify the SPI DT entry to use this driver, and add an entry
in the bcm953012k DTS file to enable the SPI.
Tested on the bcm953012k board.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the NAND entry in the DTS for the bcm953012k reference board.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's wireless home router based on BCM4708A0 with BCM4360 + BCM43217
wireless chipsets. LEDs will be hopefully added later to the DT.
According to some sources it may use the same board as EA6400 and just
differ by an original vendor firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's tri-band wireless home router based on BCM4709A0 with 3 x BCM43602
chipsets. LEDs will be hopefully added later to the DT.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Let's define the SPI controllers in the Aspeed SoCs AST2500 and
AST2400 and also enable these, as well as the chips, on the associated
platforms.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This reverts commit cab4328268 ("ARM: at91/dt: sama5d2: Use new
compatible for ohci node")
It depends from commit 7150bc9b4d ("usb: ohci-at91: Forcibly suspend
ports while USB suspend") which was reverted and implemented
differently. With the new implementation, the compatible string must
remain the same.
The compatible string introduced by this commit has been used in the
default SAMA5D2 dtsi starting from Linux 4.8. As it has never been
working correctly in an official release, removing it should not be
breaking the stability rules.
Fixes: cab4328268 ("ARM: at91/dt: sama5d2: Use new compatible for ohci node")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
cc: <stable@vger.kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The A13 hardware line is shared by SPI and MCI1 controller.This patch
disables the SPI controller so that the MCI1 (the big MMC card slot) can
be used.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The matrix node was defined before the documentation for the bus
matrix configuration was submitted. Patch the device tree to match
the DT doc.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
SFRBU, the Special Function Registers Backup manage specific aspects of the
integrated memory, bridge implementations, processor and other
functionality not controlled elsewhere.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull ARM updates from Russell King:
- nommu updates from Afzal Mohammed cleaning up the vectors support
- allow DMA memory "mapping" for nommu Benjamin Gaignard
- fixing a correctness issue with R_ARM_PREL31 relocations in the
module linker
- add strlen() prototype for the decompressor
- support for DEBUG_VIRTUAL from Florian Fainelli
- adjusting memory bounds after memory reservations have been
registered
- unipher cache handling updates from Masahiro Yamada
- initrd and Thumb Kconfig cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (23 commits)
ARM: mm: round the initrd reservation to page boundaries
ARM: mm: clean up initrd initialisation
ARM: mm: move initrd init code out of arm_memblock_init()
ARM: 8655/1: improve NOMMU definition of pgprot_*()
ARM: 8654/1: decompressor: add strlen prototype
ARM: 8652/1: cache-uniphier: clean up active way setup code
ARM: 8651/1: cache-uniphier: include <linux/errno.h> instead of <linux/types.h>
ARM: 8650/1: module: handle negative R_ARM_PREL31 addends correctly
ARM: 8649/2: nommu: remove Hivecs configuration is asm
ARM: 8648/2: nommu: display vectors base
ARM: 8647/2: nommu: dynamic exception base address setting
ARM: 8646/1: mmu: decouple VECTORS_BASE from Kconfig
ARM: 8644/1: Reduce "CPU: shutdown" message to debug level
ARM: 8641/1: treewide: Replace uses of virt_to_phys with __pa_symbol
ARM: 8640/1: Add support for CONFIG_DEBUG_VIRTUAL
ARM: 8639/1: Define KERNEL_START and KERNEL_END
ARM: 8638/1: mtd: lart: Rename partition defines to be prefixed with PART_
ARM: 8637/1: Adjust memory boundaries after reservations
ARM: 8636/1: Cleanup sanity_check_meminfo
ARM: add CPU_THUMB_CAPABLE to indicate possible Thumb support
...
Replaced the legacy binding "gpio-key,wakeup" with "wakeup-source" as
noted in the kernel documentation.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 50e95b6b85 ("ARM: dts: am57xx-idk: Add Industrial
output support") added the TPIC2810 device-tree node under
SPI bus instead of I2C1.
Fix it. Tested on AM572x IDK by driving on-board LEDs
connected to TPIC2810
Fixes: 50e95b6b85 ("ARM: dts: am57xx-idk: Add Industrial output support")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The decompress.c file contains a declaration for strstr() so we can
include some compression library code.
With the updated LZ4 implementation, we run into the same problem again
for strlen():
In file included from ../include/linux/rcupdate.h:40:0,
from ../include/linux/srcu.h:33,
from ../include/linux/notifier.h:15,
from ../include/linux/memory_hotplug.h:6,
from ../include/linux/mmzone.h:749,
from ../include/linux/gfp.h:5,
from ../include/linux/kmod.h:22,
from ../include/linux/module.h:13,
from ../arch/arm/boot/compressed/../../../../lib/lz4/lz4_decompress.c:39,
from ../arch/arm/boot/compressed/../../../../lib/decompress_unlz4.c:13,
from ../arch/arm/boot/compressed/decompress.c:55:
include/linux/cpumask.h: In function 'cpumask_parse':
include/linux/cpumask.h:592:53: error: implicit declaration of function 'strlen';did you mean 'strstr'? [-Werror=implicit-function-declaration]
This adds another declaration to work around the new problem.
Fixes: ce83d9ab80d6 ("lib: update LZ4 compressor module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Fix typos and add the following to the scripts/spelling.txt:
swith||switch
swithable||switchable
swithed||switched
swithing||switching
While we are here, fix the "update" to "updates" in the touched hunk in
drivers/net/wireless/marvell/mwifiex/wmm.c.
Link: http://lkml.kernel.org/r/1481573103-11329-2-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=o8o/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The usual collection of new drivers, non-critical fixes, and updates
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (130 commits)
clk: renesas: mstp: ensure register writes complete
clk: qcom: Do not drop device node twice
clk: mvebu: adjust clock handling for the CP110 system controller
clk: mvebu: Expand mv98dx3236-core-clock support
clk: zte: add i2s clocks for zx296718
clk: sunxi-ng: sun9i-a80: Fix wrong pointer passed to PTR_ERR()
clk: sunxi-ng: select SUNXI_CCU_MULT for sun5i
clk: sunxi-ng: Check kzalloc() for errors and cleanup error path
clk: tegra: Add BPMP clock driver
clk: uniphier: add eMMC clock for LD11 and LD20 SoCs
clk: uniphier: add NAND clock for all UniPhier SoCs
ARM: dts: sun9i: Switch to new clock bindings
clk: sunxi-ng: Add A80 Display Engine CCU
clk: sunxi-ng: Add A80 USB CCU
clk: sunxi-ng: Add A80 CCU
clk: sunxi-ng: Support separately grouped PLL lock status register
clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT
clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag
clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers
clk: qcom: SDHCI enablement on Nexus 5X / 6P
...
A total of 380 patches this time, mostly adding support for more hardware
in the device tree descriptions. There is not much exciting here for 4.11,
but I've tried my best to condense the information from the pull requests
I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now
gets fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already
supported chips
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP architecture
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero,
all based on Allwinner SoCs
http://linux-sunxi.org/LicheePi_Onehttp://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless
https://beagleboard.org/black-wirelesshttps://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam i.Core
http://www.opossom.com/english/index.htmlhttp://www.savageboard.org/http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ulhttp://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas, qcom,
rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic,
eeprom, mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ucQ/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"A total of 380 patches this time, mostly adding support for more
hardware in the device tree descriptions. There is not much exciting
here for 4.11, but I've tried my best to condense the information from
the pull requests I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now gets
fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3:
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box:
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder:
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points:
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already supported
chips:
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP
architecture:
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of
Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero, all based on
Allwinner SoCs:
http://linux-sunxi.org/LicheePi_Onehttp://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform:
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless:
https://beagleboard.org/black-wirelesshttps://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module:
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam
i.Core:
http://www.opossom.com/english/index.htmlhttp://www.savageboard.org/http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ulhttp://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
- Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas,
qcom, rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic, eeprom,
mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (380 commits)
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
ARM: DTS: Fix register map for virt-capable GIC
dt-bindings: arm,gic: Fix binding example for a virt-capable GIC
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
ARM: dts: add the AB8500 sysclk to the device trees
...
We sometimes collect non-critical fixes that come in during the later part
of the merge window in a branch for the next release instead, and this is
that contents for v4.11.
Most of these are OMAP fixes, dealing with OMAP36/37 detection, quirks
and setup. There's also some fixes for Davinci and a Kconfig fix for SCPI
to only enable on ARM{,64}.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NhZq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"We sometimes collect non-critical fixes that come in during the later
part of the merge window in a branch for the next release instead, and
this is that contents for v4.11.
Most of these are OMAP fixes, dealing with OMAP36/37 detection, quirks
and setup. There's also some fixes for Davinci and a Kconfig fix for
SCPI to only enable on ARM{,64}"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
firmware: arm_scpi: Add hardware dependencies
ARM: OMAP3: Fix SoC detection of OMAP36/37 Family
ARM: OMAP5: Add HWMOD_SWSUP_SIDLE_ACT flag for UART
ARM: dts: Fix compatible for ti81xx uarts for 8250
ARM: dts: Fix am335x and dm814x scm syscon to probe children
ARM: OMAP2+: Fix init for multiple quirks for the same SoC
ARM: dts: Fix omap3 off mode pull defines
bus: da850-mstpri: fix my e-mail address
ARM: davinci: da850: fix da850_set_pll0rate()
ARM: davinci: da850: coding style fix
Here is the big tty/serial driver patchset for 4.11-rc1.
Not much here, but a lot of little fixes and individual serial driver
updates all over the subsystem. Majority are for the sh-sci driver and
platform (the arch-specific changes have acks from the maintainer).
The start of the "serial bus" code is here as well, but nothing is
converted to use it yet. That work is still ongoing, hopefully will
start to show up across different subsystems for 4.12 (bluetooth is one
major place that will be used.)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lDg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylwfwCgyExa4x8Lur2nZyu8cgcaVRU68VAAoNQh0WJt
EZdEhEkRMt4d64j+ApYI
=iv7x
-----END PGP SIGNATURE-----
Merge tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty/serial driver patchset for 4.11-rc1.
Not much here, but a lot of little fixes and individual serial driver
updates all over the subsystem. Majority are for the sh-sci driver and
platform (the arch-specific changes have acks from the maintainer).
The start of the "serial bus" code is here as well, but nothing is
converted to use it yet. That work is still ongoing, hopefully will
start to show up across different subsystems for 4.12 (bluetooth is
one major place that will be used.)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (109 commits)
tty: pl011: Work around QDF2400 E44 stuck BUSY bit
atmel_serial: Use the fractional divider when possible
tty: Remove extra include in HVC console tty framework
serial: exar: Enable MSI support
serial: exar: Move register defines from uapi header to consumer site
serial: pci: Remove unused pci_boards entries
serial: exar: Move Commtech adapters to 8250_exar as well
serial: exar: Fix feature control register constants
serial: exar: Fix initialization of EXAR registers for ports > 0
serial: exar: Fix mapping of port I/O resources
serial: sh-sci: fix hardware RX trigger level setting
tty/serial: atmel: ensure state is restored after suspending
serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt
serdev: ttyport: check whether tty_init_dev() fails
serial: 8250_pci: make pciserial_detach_ports() static
ARM: dts: STiH410-b2260: Enable HW flow-control
ARM: dts: STiH407-family: Use new Pinctrl groups
ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control
ARM: dts: STiH410-b2260: Identify the UART RTS line
dt-bindings: serial: Update 'uart-has-rtscts' description
...
Pull networking updates from David Miller:
"Highlights:
1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
Varadhan.
2) Simplify classifier state on sk_buff in order to shrink it a bit.
From Willem de Bruijn.
3) Introduce SIPHASH and it's usage for secure sequence numbers and
syncookies. From Jason A. Donenfeld.
4) Reduce CPU usage for ICMP replies we are going to limit or
suppress, from Jesper Dangaard Brouer.
5) Introduce Shared Memory Communications socket layer, from Ursula
Braun.
6) Add RACK loss detection and allow it to actually trigger fast
recovery instead of just assisting after other algorithms have
triggered it. From Yuchung Cheng.
7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.
8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.
9) Export MPLS packet stats via netlink, from Robert Shearman.
10) Significantly improve inet port bind conflict handling, especially
when an application is restarted and changes it's setting of
reuseport. From Josef Bacik.
11) Implement TX batching in vhost_net, from Jason Wang.
12) Extend the dummy device so that VF (virtual function) features,
such as configuration, can be more easily tested. From Phil
Sutter.
13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
Dumazet.
14) Add new bpf MAP, implementing a longest prefix match trie. From
Daniel Mack.
15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.
16) Add new aquantia driver, from David VomLehn.
17) Add bpf tracepoints, from Daniel Borkmann.
18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
Florian Fainelli.
19) Remove custom busy polling in many drivers, it is done in the core
networking since 4.5 times. From Eric Dumazet.
20) Support XDP adjust_head in virtio_net, from John Fastabend.
21) Fix several major holes in neighbour entry confirmation, from
Julian Anastasov.
22) Add XDP support to bnxt_en driver, from Michael Chan.
23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.
24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.
25) Support GRO in IPSEC protocols, from Steffen Klassert"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
Revert "ath10k: Search SMBIOS for OEM board file extension"
net: socket: fix recvmmsg not returning error from sock_error
bnxt_en: use eth_hw_addr_random()
bpf: fix unlocking of jited image when module ronx not set
arch: add ARCH_HAS_SET_MEMORY config
net: napi_watchdog() can use napi_schedule_irqoff()
tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
net/hsr: use eth_hw_addr_random()
net: mvpp2: enable building on 64-bit platforms
net: mvpp2: switch to build_skb() in the RX path
net: mvpp2: simplify MVPP2_PRS_RI_* definitions
net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
net: mvpp2: remove unused register definitions
net: mvpp2: simplify mvpp2_bm_bufs_add()
net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
net: mvpp2: release reference to txq_cpu[] entry after unmapping
net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
...
Fix typos introduced during the preparation of the 4.11 merge window.
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWKXgiiMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71YtfAJ9CORkmYU3+
eFLwSeHXruxk4FBUpwCgnIAMxqAeW9JwZxfYXmw3ip0IyAI=
=h8++
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.11-4' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.11 (part 4)" from Gregory CLEMENT:
Fix typos introduced during the preparation of the 4.11 merge window.
* tag 'mvebu-dt-4.11-4' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
- Add support for phyCORE-AM335x PCM-953 carrier board
- Add power button and charger support for am335x-chiliboard
-----BEGIN PGP SIGNATURE-----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=TN7G
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Few more late dts changes for omaps for v4.11 merge window" from Tony Lindgren:
- Add support for phyCORE-AM335x PCM-953 carrier board
- Add power button and charger support for am335x-chiliboard
* tag 'omap-for-v4.11/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: dts: Add support for phyCORE-AM335x PCM-953 carrier board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZulM
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.11/dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "Enable SATA support on DA850 LCDK" from Sekhar Nori:
* tag 'davinci-for-v4.11/dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: enable the SATA node
ARM: dts: da850: add the SATA node
devicetree: bindings: add bindings for ahci-da850
The switch to the new DSA binding used "marvell,mv88e6095" for the
compatible property which doesn't exist, use "marvell,mv88e6085"
instead.
Fixes: 455b82f03f ("ARM: dts: armada-385-linksys: Utilize new DSA binding")
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The compatible should be 98dx4251 not 98dx4521.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Support for the audio codec and Mali GPU for the A33
-----BEGIN PGP SIGNATURE-----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=X2M/
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT changes for 4.11, part 2" from Maxime Ripard:
Support for the audio codec and Mali GPU for the A33
* tag 'sunxi-dt-for-4.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
The usual chunk of DT changes, most notably:
- Support for the H2+ and the V3s
- CPUFreq support for the A33
- SPDIF support for the A31 and H3
- New boards: Beelink X2, Lichee Pi One, Lichee Pi Zero,
Orange Pi Zero
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYkFCYAAoJEBx+YmzsjxAgljYP/0seq1LEtMtoTeXHP6ZPkrju
7/pHjEwJFZRH98DZ0QMAcUM+fHB0C4h5UadEXCIyzYBO9yeHzm+Hoys4VvpaQasL
6taHz3zJ5T1/si7HyyP16LEwaFeARmSO3aXh4t5195Y2u3BFD+b2i5BpMquCC5CM
XXJmx3Q487bUWjdufUqiSz0gWK1BfKw/eJAawoJbIl9Z6v7wOvE0SQF8ZtIc2eOl
WX9uyNKdYh4PsSC0TxexDeKHNhLh2hJgO1HxYg+DTdyGM144XO0OSuPFtfilROaL
tViKBohffz8A4K5m5iCaDva+P9318iO2xVN91/DFV6VS2XhMRvUrfZRd9kEvuhvu
FJF3KrIZDLRu7tkcHVt9GDjO3CElejMT+qLOGg7t+9nJ+6RjyHUSBs6HIU0Opsu0
Fw7LyHihzDH/m7m87lxUUmC5rSRqMVfuiKwphHYqDzkYEGEnL4kv055rE6cBFGyM
zr7aajpiFgARPXj1XdZQRnz8uC8kySUf2o1oLPdhP3szX41AWBTiBuT7yqMB6qnD
5B8Xj4zTsjEYfwsaWaI8VhbK2UsLgsUlbUXugKfqtjoPTjaWN6zQ3C6030Bov9za
2jo0+187iYp/B/M4DPiH3Kicfntnj4DWRmBt8wCX/PVXS2tD1S617JzugbX/+EZK
PF328UgsT3c1UkccBK9/
=ig5Q
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT changes for 4.11" from Maxime Ripard:
The usual chunk of DT changes, most notably:
- Support for the H2+ and the V3s
- CPUFreq support for the A33
- SPDIF support for the A31 and H3
- New boards: Beelink X2, Lichee Pi One, Lichee Pi Zero,
Orange Pi Zero
* tag 'sunxi-dt-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (42 commits)
ARM: dts: sun8i-h3: Add SPDIF to the Beelink X2
ARM: dts: sun8i-h3: Add the SPDIF block to the H3
ARM: dts: sun8i-h3: Add SPDIF TX pin to the H3
ARM: dts: sun8i-h3: Add dts for the Beelink X2 STB
ARM: sun8i: sina33: Enable display
ARM: sun8i: a23/a33: Add the oscillators accuracy
ARM: sun8i: a23/a33: Enable the real LOSC and use it
ARM: dts: sunxi: add support for Lichee Pi Zero board
ARM: dts: sunxi: add dtsi file for V3s SoC
ARM: dts: sun6i: sina31s: Enable USB OTG controller in peripheral mode
ARM: dts: sun8i: reference-design: use AXP223 DTSI
ARM: dts: sun8i: parrot: use AXP223 DTSI
ARM: dts: sun8i: sina33: use AXP223 DTSI
ARM: dts: sun8i: a33-olinuxino: use AXP223 DTSI
ARM: dts: add DTSI for AXP223
dt-bindings: power: axp20x-usb: add axp223 compatible
ARM: dts: sun7i: Add wifi dt node on Banana Pro
ARM: dts: sun6i: Add SPDIF to the Mele I7
devicetree: bindings: Add vendor prefix for Shenzhen Xunlong Software
ARM: dts: sun8i-h3: orange-pi-pc: Enable audio codec
...
1. Add descriptive user-friendly label names for power domains. This
makes debugging easier.
-----BEGIN PGP SIGNATURE-----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=SE3a
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DeviceTree update for v4.11, third round" from Krzysztof Kozlowski
1. Add descriptive user-friendly label names for power domains. This
makes debugging easier.
* tag 'samsung-dt-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add labels to all existing power domains
This cleans the device tree a bit and rectifies some
clocking bugs. They are in a sense regressions, but there
is no hurry for this platform.
-----BEGIN PGP SIGNATURE-----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=QJk8
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Pull "Ux500 Device Tree updates for v4.11" from Linus Walleij:
This cleans the device tree a bit and rectifies some
clocking bugs. They are in a sense regressions, but there
is no hurry for this platform.
* tag 'ux500-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: add the AB8500 sysclk to the device trees
ARM: dts: Ux500: move USB PHY pins to PHY device
ARM: dts: push MMC/SD to board and add comments
Add support for Marvell switches with integrated CPUs based on Armada XP
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWJCV2yMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71SkdAJ0S0Drnjneu
0rdBe1D5BsfMyao7pQCgpGRbAwKc6mtY4w78uFxahRUNdxI=
=3/jm
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.11-3' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt for 4.11 (part 3)" from Gregory CLEMENT:
Add support for Marvell switches with integrated CPUs based on Armada XP
* tag 'mvebu-dt-4.11-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
ARM: dts: mvebu: Add device tree for 98DX3236 SoCs
Since everybody copied my own mistake from the DT binding example,
let's address all the offenders in one swift go.
Most of them got the CPU interface size wrong (4kB, while it should
be 8kB), except for both keystone platforms which got the control
interface wrong (4kB instead of 8kB).
In a few cases where I knew for sure what implementation was used,
I've added the "arm,gic-400" compatible string. I'm 99% sure that
this is what everyone is using, but short of having the TRM for
all the other SoCs, I've left them alone.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
More consistent naming for some orion5x based boards helping the
switch to device tree for debian users.
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWJNvuSMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71bUAAJ9F2ae0LEvo
4Fu44238w1Kr6hC6LQCeO16PL46cLMTZj2E/hOy/9eytbM0=
=IcBG
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.10-1' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fixes for 4.10 (part 1)" from Gregory CLEMENT:
More consistent naming for some orion5x based boards helping the
switch to device tree for debian users.
* tag 'mvebu-fixes-4.10-1' of git://git.infradead.org/linux-mvebu:
ARM: orion5x: fix Makefile for linkstation-lschl.dtb
ARM: dts: orion5x-lschl: More consistent naming on linkstation series
ARM: dts: orion5x-lschl: Fix model name
Hardware flow-control capability must be specified at a platform
level in order to inform the ASC driver that the platform is capable
(i.e. are the lines wired up, etc). STiH4{07,10} devices are indeed
capable, so let's provide the property.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having just defined some new Pinctrl groups for when HW flow-control
is {en,dis}abled, let's reference them for use within the driver.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each serial port which supports HW flow-control should have 2 Pinctrl
groups. One for when HW flow-control is in progress, where the IP
will take over controlling the lines and another group which enables
the lines to be toggled using GPIO mechanisms.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When hardware flow-control is disabled, manual toggling of the UART's
reset line (RTS) using userland applications (e.g. stty) is not
possible, since the ASC IP does not provide this functionality in the
same was as some other IPs do. Thus, we have to do this manually.
This patch configures the UART RTS line as a GPIO for manipulation
within the UART driver when HW flow-control is not enabled.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the audio codec and the audio dai for the sun8i A33 sinlinx board.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the audio codec and the audio dai for the sun8i R16 Parrot board.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the audio codec, dai and a simple card to be able to use the
audio stream of the builtin codec on sun8i SoC.
This commit adds also an audio-routing for the sound card node to link
the analog DAPM widgets (Right/Left DAC) and the digital one's as they
are created in different drivers.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the device tree entries needed to support the EMAC AXI
bus settings on the Arria10 SoCFPGA chip.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
chiliBoard has a battery connector, so support charging battery
through tps65217 chip.
Additionally, enabling tps65217 charger allows us to get status
of AC power.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On chiliBoard power button is connected to TPS65217. It signals power
button presses by asserting interrupt output and allows to read the
state by i2c bus.
Handle TPS65217 interrupts and enable notifications of power button
presses.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The rename of orion5x-lschl.dts needs to be reflected in the Makefile:
make[3]: *** No rule to make target 'arch/arm/boot/dts/orion5x-lschl.dtb', needed by '__build'.
Fixes: 6cfd3cd8d8 ("ARM: dts: orion5x-lschl: More consistent naming on linkstation series")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The A23 and A33 have an ARM Mali 400 GPU. Now that we have a binding, add
it to our DT.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Define and enable pwm1 and pwm3 for stm32f469 discovery board
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add Timers and it sub-nodes into DT for stm32f429 family.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This clock has been missing since some early stages of device tree
conversion. Adding the right clocks to the device tree makes USB
work again.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The physical pins from the SoC are in a sense belonging to the
PHY device (AB8500 USB) rather than the MUSB USB IP block.
The driver definately assumes so: before this change it
complains that it cannot control the pins it is using:
abx5x0-usb ab8500-usb.0: could not get/set default pinstate
After this patch the warning goes away.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the enable-active-high setting from the SoC to the
board for the VMMCQ regulators. It should at least be in the
vicinity of the GPIO line it is defined for.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide human readable names for all power domains defined in Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
These boards are Marvell's evaluation boards for the 98DX4251 and
98DX3336 SoCs.
[gregory.clement@free-electrons.com: fix topic and update Makefile]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
with integrated CPUs. They are similar to the Armada XP SoCs but have
different I/O interfaces.
[gregory.clement@free-electrons.com: fix topic]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable the SATA node for da850-lcdk. We omit the pinctrl property on
purpose - the muxed SATA pins are not hooked up to anything
SATA-related on the lcdk.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
DTS files, which includes orion5x-linkstation.dtsi, are named:
orion5x-linkstation-*.dts
So we rename the file below:
arch/arm/boot/dts/orion5x-lschl.dts
to the new name:
arch/arm/boot/dts/orion5x-linkstation-lschl.dts
Because DTS conversion of this device was just introduced in 4.9, Debian
is still using legacy device support, other distros are the same,
so here we won't expect any impact actually.
Fixes: f94f268979 ("ARM: dts: orion5x: convert ls-chl to FDT")
Cc: Ashley Hughes <ashley.hughes@blueyonder.co.uk>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Model name should be consistent with legacy device file, so that user
can migrate their system from legacy device support to device-tree
safely.
Legacy device file is currently removed, but it can be found on 4.8
or previous version of linux:
arch/arm/mach-orion5x/ls-chl-setup.c
Fixes: f94f268979 ("ARM: dts: orion5x: convert ls-chl to FDT")
Cc: Ashley Hughes <ashley.hughes@blueyonder.co.uk>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a DT binding documentation for the Video Data Order Adapter (VDOA)
of the Freescale i.MX6 SoC.
Also, add the compatible property and correct clock to the device tree
to match the documentation.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that we have a full clock driver for sun9i, switch to it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
1. Use bigger reserved memory region for Multi Format Codec on all Exynos
chipsets so it could decode FullHD easily.
-----BEGIN PGP SIGNATURE-----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=E4FL
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree update for v4.11, second round:
1. Use bigger reserved memory region for Multi Format Codec on all Exynos
chipsets so it could decode FullHD easily.
* tag 'samsung-dt-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix indentation of EHCI and OHCI ports
ARM: dts: exynos: Increase MFC left reserved memory region size
Signed-off-by: Olof Johansson <olof@lixom.net>
- New board support: vf610-zii-dev-rev-c, imx6ul-opos6uldev,
imx6ul-isiot, imx6qdl-savageboard, imx6q-mccmon6.
- A patch from Alexandre to correct the mangled license text which
has been copied & pasted all over the i.MX device tree files.
- Update cpu nodes of some i.MX SoCs to make them consistent and match
ePAPR spec.
- Add OCOTP device for i.MX6UL SoC.
- Add security violation interrupt for i.MX25 DryIce.
- Enable USB OTG, WIFI and Bluetooth support for i.MX6SX Udoo Neo
board.
- Enable S/PDIF and 2nd display pipeline support for CompuLab board..
- Add SPI and LTC3676 PMIC support for Gateworks Ventana boards.
- A few random device addition for various boards: TVE DAC regulators
for imx53-qsb, EEPROM for vf610-zii-dev, eMMC and NAND support for
i.MX6UL Engicam boards.
- Cleanups on obsoleted or unused properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjWLQAAoJEFBXWFqHsHzOGt0H/2WCsuRi6WU7i7Wyk/S0Xq5t
HzA/9m2f7z1vb1tzFknbpcWYa9bdofI7Dz+6KW2vp4fxhMyJn8SQxWwQjVNya2ba
z8XLdEMlIuozBebPcH84ovNzqoBIOEFahGm5smm40s/o7XL8ua9tOEFaUc+jY0Pd
n/3TPmoyBTlbrgiCZfLXCVsczHtEVW5JoQmXT7aDsxT0BQpnwLbgXKVOxgDvsWXM
WtAKjpGvdiApD3znbFjYmRKak+2uilkV5B4jrL4mZf8dxCliykP4XA/LbiMLKAMN
voMpTtTK7UYp59GrwKbqfJ+pPU7b6ndKK59f7FWrTDNgtDGe+J4ExjWwsDnuLfI=
=HAbg
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree updates for 4.11:
- New board support: vf610-zii-dev-rev-c, imx6ul-opos6uldev,
imx6ul-isiot, imx6qdl-savageboard, imx6q-mccmon6.
- A patch from Alexandre to correct the mangled license text which
has been copied & pasted all over the i.MX device tree files.
- Update cpu nodes of some i.MX SoCs to make them consistent and match
ePAPR spec.
- Add OCOTP device for i.MX6UL SoC.
- Add security violation interrupt for i.MX25 DryIce.
- Enable USB OTG, WIFI and Bluetooth support for i.MX6SX Udoo Neo
board.
- Enable S/PDIF and 2nd display pipeline support for CompuLab board..
- Add SPI and LTC3676 PMIC support for Gateworks Ventana boards.
- A few random device addition for various boards: TVE DAC regulators
for imx53-qsb, EEPROM for vf610-zii-dev, eMMC and NAND support for
i.MX6UL Engicam boards.
- Cleanups on obsoleted or unused properties.
* tag 'imx-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (32 commits)
ARM: dts: udoo_neo: Add Bluetooth support
ARM: dts: udoo_neo: Add Wifi support
ARM: dts: udoo_neo: Add UDOO Neo USB OTG1 and OTG2 support
ARM: dts: imx6ul: Add Engicam Is.IoT MX6UL NAND initial support
ARM: dts: imx6ul: Add Engicam Is.IoT MX6UL eMMC initial support
ARM: dts: imx6qdl: Fix "ERROR: code indent should use tabs where possible"
ARM: dts: vf610-zii-dev: add EEPROM entry to Rev C
ARM: dts: add Armadeus Systems OPOS6UL and OPOS6ULDEV support
ARM: dts: imx6q-utilite-pro: enable 2nd display pipeline
ARM: dts: vf610-zii-dev: Add .dts file for rev. C
ARM: dts: vf610-zii-dev-rev-b: Remove leftover PWM pingroup
ARM: dts: imx6: Support Savageboard quad
ARM: dts: imx6: Support Savageboard dual
ARM: dts: imx6: Add Savageboard common file
ARM: dts: imx53-qsb: Provide the TVE DAC regulators
ARM: dts: imx6q: Add mccmon6 board support
Doc: devicetree: bindings: Add vendor prefix entry - lwn
ARM: dts: imx/vf: Correct license text
ARM: dts: imx25.dtsi: DryIce security violation interrupt
ARM: dts: imx: Add ocotp node for imx6ul
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- A couple of fixes on anatop regulator voltage and constraints
according to hardware datasheet.
- Correct FEC interrupt routing for i.MX6QP which has got the hardware
bug found on i.MX6Q fixed.
- Remove unit address from i.MX6 LDB device node to fix DTC warning.
- A fix on imx53-qsb board FEC pinmux config to remove the dependency
on firmware for setting up pins.
- A series from Sascha to fix LPSR pins for i.MX7 boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjVP+AAoJEFBXWFqHsHzOcvEIAKmxLYG5bmXkUNm+cJQ0oJde
MPh984lN1Xzx0PFlXJoC3mMC4W0RCibLjjSMS3s28ddzw0AKyAWHVkPDzUtuFQOT
s7iUjgXhfpwxeIt5DGZUXbzfZVXjRrVgWfYSMPnc2Q+PUAHQDhqTqylCTz5yF6qf
/XpN5uBaq/h++CJ+e06h9xSuIaCcEtGzLoUA+qXJBseBCLxlaR7zlt5bVL338oOt
P8LuKk8Xcmc6QstpC5HyH8XuHQ8h+Gj0tLKkFeEnLY5JFmRo6e1wOq9EPW+AHfBp
vgW5cI5cgdtn7/TuAbmCOoE052jd8oVK3LnKEfFXHxcBCDIDYz580CdbTFe06+g=
=tRE+
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-nc-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX non-critical device tree fixes for 4.11:
- A couple of fixes on anatop regulator voltage and constraints
according to hardware datasheet.
- Correct FEC interrupt routing for i.MX6QP which has got the hardware
bug found on i.MX6Q fixed.
- Remove unit address from i.MX6 LDB device node to fix DTC warning.
- A fix on imx53-qsb board FEC pinmux config to remove the dependency
on firmware for setting up pins.
- A series from Sascha to fix LPSR pins for i.MX7 boards.
* tag 'imx-fixes-nc-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx53-qsb-common: fix FEC pinmux config
ARM: imx6: remove unit address from LDB node
ARM: imx6qp: adapt DT to changed FEC interrupts
ARM: imx6: fix regulator constraints on anatop 1p1 and 2p5
ARM: imx6: fix min/max voltage of anatop 2p5 regulator
ARM: dts: imx7: Add "LPSR" to LPSR iomux pin names
ARM: dts: imx7d-cl-som: Fix OTG power pinctrl
ARM: dts: imx7d-sdb: Fix watchdog and pwm pinmux
ARM: dts: imx7s-warp: Fix watchdog pinmux
Signed-off-by: Olof Johansson <olof@lixom.net>
Switch device tree files to the new DSA binding
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWIt8ZyMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71fx4AJ4mibAO0PUJ
Hbts4+PNC5f8PMYHlQCeIDfqtqLKlfJMVH3YFasSLYmb0lo=
=PRxv
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.11-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.11 (part 2)
Switch device tree files to the new DSA binding
* tag 'mvebu-dt-4.11-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood-rd88f6281: Utilize new DSA binding
ARM: dts: kirkwood-mv88f6281gtw-ge: Utilize new DSA binding
ARM: dts: kirkwood-linksys-viper: Utilize new DSA binding
ARM: dts: kirkwood-dir665: Utilize new DSA binding
ARM: dts: armada-xp-linksys-mamba: Utilize new DSA binding
ARM: dts: armada-388-clearfog: Utilize new DSA binding
ARM: dts: armada-385-linksys: Utilize new DSA binding
ARM: dts: armada-370-rd: Utilize new DSA binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Since v4.10-rc1, xhci is complaining in loop with :
[ 801.953836] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 801.960455] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 801.966611] usb usb6-port1: cannot disable (err = -32)
set property "snps,dis_u3_susphy_quirk" in DT fix it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+Frf
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into fixes
STi DT fix:
Since v4.10-rc1, xhci is complaining in loop with :
[ 801.953836] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 801.960455] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 801.966611] usb usb6-port1: cannot disable (err = -32)
set property "snps,dis_u3_susphy_quirk" in DT fix it.
* tag 'sti-dt-for-v4.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH407-family: set snps,dis_u3_susphy_quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
This contains a set of patches that add hardware compatibility for newer
revisions of the Toradex Apalis TK1. Also included is a fix to the PAZ00
that stabilizes panel initialization on boot as well as a patch to add
card detection for the µSD card slot on TrimSlice.
To round things off there are a couple of fixes and changes to the Nyan
device tree files to fix the battery charger, add compatibility with new
revisions of Nyan Blaze and Nyan Big, as well as properly support the
TPM.
-----BEGIN PGP SIGNATURE-----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=QqnB
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.11-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.11-rc1
This contains a set of patches that add hardware compatibility for newer
revisions of the Toradex Apalis TK1. Also included is a fix to the PAZ00
that stabilizes panel initialization on boot as well as a patch to add
card detection for the µSD card slot on TrimSlice.
To round things off there are a couple of fixes and changes to the Nyan
device tree files to fix the battery charger, add compatibility with new
revisions of Nyan Blaze and Nyan Big, as well as properly support the
TPM.
* tag 'tegra-for-4.11-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: nyan-blaze: Proper pinmux for TPM I2C
ARM: tegra: nyan-big: Proper pinmux for TPM I2C
ARM: tegra: nyan-blaze: Include compatible revisions for proper detection
ARM: tegra: nyan-big: Include compatible revisions for proper detection
ARM: tegra: nyan: Use external control for bq24735 charger
ARM: tegra: nyan: Use proper IRQ type definitions
ARM: dts: tegra: Fix missing card detection in Trimslice µSD card slot
ARM: tegra: paz00: Mark panel regulator as enabled on boot
ARM: tegra: apalis-tk1: Update compatibility comment
ARM: tegra: apalis-tk1: Fix SD card detect on v1.1 HW
ARM: tegra: apalis-tk1: Adjust pin muxing for v1.1 HW
ARM: tegra: apalis-tk1: Optional DisplayPort hot-plug detect
ARM: tegra: apalis-tk1: Pull-up temperature alert
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable the DMA on sama5d2 and sama5d4 xplained to fix an issue seen by
kernelci
-----BEGIN PGP SIGNATURE-----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=MsBR
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.11-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT for 4.11 #2:
- Enable the DMA on sama5d2 and sama5d4 xplained to fix an issue seen by
kernelci
* tag 'at91-ab-4.11-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: Enable DMA on sama5d2_xplained console
ARM: dts: at91: Enable DMA on sama5d4_xplained console
Signed-off-by: Olof Johansson <olof@lixom.net>
Enhancements:
* Add power-domains to mmcif on r7s72100 SoC
* Add OSTM to rskrza1/r7s72100
* Link ARM GIC to clock and clock domain on r8a774[35] SoCs
Clean-up:
* Correct SATA device status on r8a7779/marzen
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5/D6
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.11
Enhancements:
- Add power-domains to mmcif on r7s72100 SoC
- Add OSTM to rskrza1/r7s72100
- Link ARM GIC to clock and clock domain on r8a774[35] SoCs
Clean-up:
- Correct SATA device status on r8a7779/marzen
* tag 'renesas-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r7s72100: add power-domains to mmcif
ARM: dts: rskrza1: add ostm DT support
ARM: dts: r7s72100: add ostm to device tree
ARM: dts: r7s72100: add ostm clock to device tree
ARM: dts: r8a7745: Link ARM GIC to clock and clock domain
ARM: dts: r8a7743: Link ARM GIC to clock and clock domain
ARM: dts: r8a7779, marzen: Fix sata device status
Signed-off-by: Olof Johansson <olof@lixom.net>
changes add earlycon stdout-path propety for the SoCs so far
tested with it. The other changes are addition of BeagleBone
green and making WLAN work on BeagleBone black wireless and
green wireless. The rest of the changes are the usual enabling
features on various devices:
- Enable devices on am335x-sl50
- Changes to dra7-evm boards to enable enable irqs for dp83867
eth phys, add pinmux configuration for mmc, remov erratum
i869 pinmux configurations, disable NAND support because of
pin conflict, add pcf8575 used for lcd
- Remove NAND partition table for omap3-igep
- Configure USB Ethernet MAC from device tree for beagleboard
xm, pandaboard, omap5-uevm and igepv5
- Configure am335x-chilisom to wake from RTC-only state
- Update Nanobone for external FRAM chip
- Clean up n900 dts
- Update am335x-phycore and am335x-wega for various devices
- Changes for am57xx-beagle-x15 to implement rgmii2 errata
-----BEGIN PGP SIGNATURE-----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=URbm
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.11 merge window. These
changes add earlycon stdout-path propety for the SoCs so far
tested with it. The other changes are addition of BeagleBone
green and making WLAN work on BeagleBone black wireless and
green wireless. The rest of the changes are the usual enabling
features on various devices:
- Enable devices on am335x-sl50
- Changes to dra7-evm boards to enable enable irqs for dp83867
eth phys, add pinmux configuration for mmc, remov erratum
i869 pinmux configurations, disable NAND support because of
pin conflict, add pcf8575 used for lcd
- Remove NAND partition table for omap3-igep
- Configure USB Ethernet MAC from device tree for beagleboard
xm, pandaboard, omap5-uevm and igepv5
- Configure am335x-chilisom to wake from RTC-only state
- Update Nanobone for external FRAM chip
- Clean up n900 dts
- Update am335x-phycore and am335x-wega for various devices
- Changes for am57xx-beagle-x15 to implement rgmii2 errata
* tag 'omap-for-v4.11/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (35 commits)
ARM: dts: dra72/1-evm: add pcf8575 used for lcd
ARM: dts: dra7xx: Add stdout-path property
ARM: dts: am57xx: Add stdout-path property
ARM: dts: am43xx: Add stdout-path property
ARM: dts: am33xx: Add stdout-path property
ARM: dts: am335x-sl50: Enable the Ambient Light Sensor.
ARM: dts: am335x-sl50: Enable the MCP23017 GPIO Expander.
ARM: dts: am335x-sl50: Enable BQ32000 Real Time Clock.
ARM: dts: am335x-sl50: Enable SPI0 interface and Flash Memory.
ARM: dts: am335x-sl50: Enable UART1.
ARM: dts: am335x-sl50: Remove I2C1 node.
ARM: dts: omap3-igep: Remove NAND partition table
ARM: dts: am57xx-beagle-x15: implement errata "Ethernet RGMII2 Limited to 10/100 Mbps"
ARM: dts: am335x-phycore-som: Remove partition tables
ARM: dts: dra72-evm-revc: enable irqs for dp83867 eth phys
ARM: dts: Configure BeagleBone peripheral USB VBUS irq
ARM: dts: omap5-igep0050: Allow bootloader to configure USB Ethernet MAC
ARM: dts: omap5-uevm: Allow bootloader to configure USB Ethernet MAC
ARM: dts: pandaboard: Allow bootloader to configure USB Ethernet MAC
ARM: omap3: beagleboard-xm: dt: Add ethernet to the device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
spare-compatible as all others have, conversion to gpio constants
and addition of rk3288 qos nodes that need to be saved before a
power-domain gets turned off.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAliBUsIQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgZKBB/9BVOysNvR/vLcao9jlU/an7c5vAwBdDl/G
uvsAgVAYRT2FUPcy7LPIQCoQOkk9HA3kMwiKVJH+hGQ+/0FdrKZvKkln/Yb/bT+9
GgQT2NblgNNDMfE76xQM0c7Y7Kj1oDrkGaAmdumnUPOSwMnSlxKD5j3fS2k4fz/t
ZOnqHxfEVDldmPIe4C58X5aqsQ4OmAgE7uiykZ4P3Vc0le71/QtJ4jsx4kkXNh9l
1+tGDfc1axmze/rEohw+BbNm3H5l8xMKFURlNE1Sr4dbW1y4o99mG7JVuxxfAQqd
XYP76I2foNtaxKgW29sQs0vopw9UimUiIH9i8xu4UsOWoj6N29Gj
=B1HN
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Bit of cleanup for the cortex-a9 uarts to have that soc-specific
spare-compatible as all others have, conversion to gpio constants
and addition of rk3288 qos nodes that need to be saved before a
power-domain gets turned off.
* tag 'v4.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add soc-specific uart compatibles for rk3066/rk3188
ARM: dts: rockchip: use pin constants to describe gpios
ARM: dts: rockchip: add qos node for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
Replace spaces with tabs in EHCI and OHCI ports indentation.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
The pinmux configuration in device tree was different from manual
muxing in <u-boot>/board/freescale/mx53loco/mx53loco.c
All pins were configured as NO_PAD_CTL(1 << 31), which was fine as the
bootloader already did the correct pinmuxing for us.
But recently u-boot is migrating to reuse device tree files from the
kernel tree, so it seems to be better to have the correct pinmuxing in
our files, too.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Udoo Neo has a TI WL1831 Bluetooth chip connected to the UART3 port.
Add support for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Udoo Neo has a TI WL1831 Wifi chip connected to the USDHC3 port.
Add support for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for micro USB (OTG1) and USB Host (OTG2) for UDOO Neo board.
Tested on a UDOO Neo Full board by mounting a mass storage device
on both ports.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LDB has no reg property as it uses the IOMUX-GPR syscon to access
its registers. Remove the unit address from the DT node to make DT
compiler happy.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6QP the FEC interrupts are wired to the GPC, just like all other
device interrupts. This allows to FEC to wake the CPU from WFI, but for
this to work the kernel needs to know about the new IRQ routing.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the min/max voltage constraints for the anatop 1p1 and 2p5
regulator to match the typical operating range mentioned in the
datasheet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The regulation bound of this regulator are 2.1V to 2.875V, the
wrong DT values cause the driver to miscalculate the effective
voltage.
This isn't really an issue right now, as nobody actively changes
the regulator voltage, but better fix it now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX7 has two iomux controllers. the iomuxc and the iomuxc_lpsr.
In a board dts we have to make sure that both controllers are supplied
with the correct pins. It's way too easy to do this wrong since only
a look into the reference manual can reveal which pins belong to which
controller. To make this clearer add "LPSR" to the pin names which
belong to the LPSR controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPIO01_IO05 is controlled by the LPSR iomux controller, so attach
the corresponding pin to this controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog pin and the pwm output pin are controlled by the
iomuxc_lpsr, not the regular iomux, so move the pins there.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog pin is controlled by the iomuxc_lpsr, not the regular
iomux, so move it there.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sizes of the MFC reserved memory regions for CMA are 16 MiB for the
left bank and 8 MiB for the right bank. But this isn't enough to decode
high resolution videos so increase the size for the left bank to 36 MiB
which is enough for 1080p (1920x1080).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable the S/PDIF transmitter that is present on the Beelink X2 STB.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF transceiver controller block to the H3 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF TX pin to the H3 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Fix a 'defined but not used' warning in MMDC driver when
CONFIG_PERF_EVENTS is disabled.
- Fix i.MX6DL device tree GPIO4_11 range setting.
- A bandaid fix for boot failure found on a couple of platforms due to
missing 'chosen' and 'memory' node.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYihihAAoJEFBXWFqHsHzOpUsH/2u6xsOfLENcJ4JhSm1Xk3An
rSbOrl2OcphdYLC8jx6abKHknS/Tv1oxRQWjpZRse6CONV0e5LGm129c1/ZpgBat
lC35ApK+uv9iPRQkmOKotOSWchOPr3jfmIeSxJnCTLtmQfOhDwfxbYfuZHooNa5t
Ql0qD3wEc5+hjKGyNkWgFx7P+HmYB7m8BS/d4Daih6rQPtHGuIzf700SIpqQ+J40
/czLm0Ei0bJiOM8BwBFoHOhvqomkNWbMh5RR/lOhSwXdJ0EkEHXZ2196WEADEUbw
LuPHZqvihuZNSvdVfB5UoPjkpRPu4yTq12M9kGO9hxqN8QLBVE6VbcVonQEFlTo=
=QI4I
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into HEAD
Pull "i.MX fixes for 4.10, 3rd round" from Shawn Guo:
- Fix a 'defined but not used' warning in MMDC driver when
CONFIG_PERF_EVENTS is disabled.
- Fix i.MX6DL device tree GPIO4_11 range setting.
- A bandaid fix for boot failure found on a couple of platforms due to
missing 'chosen' and 'memory' node.
* tag 'imx-fixes-4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: Pass 'chosen' and 'memory' nodes
ARM: dts: imx6dl: fix GPIO4 range
ARM: imx: hide unused variable in #ifdef
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The datasheet provided by Allwinner requires oscillators with an accuracy
of 50ppm. Add it to our fixed clocks so that we can properly track the
accuracy chain.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
So far, the LOSC was generated through the RTC internal oscillator, which
was a pretty poor and inaccurate choice.
Now that the RTC properly exposes its internal mux between its oscillator
and the external oscillator, we can use it were relevant.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Lichee Pi Zero is a small-sized V3s board, which is
breadboard-compatible, and with a MicroUSB port with both OTG function
and power function.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we have the pinctrl and clock support for the V3s SoC, it's now to
run a mainline Linux on it.
So add a .dtsi file for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
[Maxime: Removed the dependency on the CCU headers]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since v4.10-rc1, the following logs appears in loop :
[ 801.953836] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 801.960455] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 801.966611] usb usb6-port1: cannot disable (err = -32)
[ 806.083772] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 806.090370] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 806.096494] usb usb6-port1: cannot disable (err = -32)
After analysis, xhci try to set link in U3 and returns an error.
Using snps,dis_u3_susphy_quirk fix this issue.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The phyCORE-AM335x development kit is a combination of the
phyCORE-AM335x SoM and a PCM-953 carrier board. The features
of the PCM-953 are:
* ETH phy on carrier board: 1x RGMII
* 1x CAN
* Up to 4x UART
* USB0 (otg)
* USB1 (host)
* SD slot
* User gpio-keys
* User LEDs
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the Arria10, because of hardware bug, watchdog0 cannot reliably trigger
a reset to the CPU. The workaround would be to use watchdog1 instead.
Also for watchdog1, there is a dependency on the bootloader to enable the
boot_clk source to be from the cb_intosc_hs_clk/2, versus from EOSC1. This
corresponds to the (SWCTRLBTCLKEN & SWCTRLBTCLKSEL) bits enabled in the
control register in the clock manager module of Arria10.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This corrects the pinmux for accessing the TPM over the I2C line. Thus,
it allows correctly probing the module, that previously failed with I2C
errors.
Signed-off-by: Jerome Coste <jerome.coste@etu.utc.fr>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This corrects the pinmux for accessing the TPM over the I2C line. Thus,
it allows correctly probing the module, that previously failed with I2C
errors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Depthcharge (the payload used with cros devices) will attempt to detect
boards using their revision. This includes all the known revisions for
the nyan-blaze board so that the dtb can be selected preferably.
Defining compatibly revisions allows depthcharge to select the kernel
via the revision it detects instead of using the default kernel. This
allows having a FIT image with multiple kernels for multiple devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Depthcharge (the payload used with cros devices) will attempt to detect
boards using their revision. This includes all the known revisions for
the nyan-big board so that the dtb can be selected preferably.
Defining compatibly revisions allows depthcharge to select the kernel
via the revision it detects instead of using the default kernel. This
allows having a FIT image with multiple kernels for multiple devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nyan boards come with an embedded controller that controls when to
enable and disable the charge. Thus, it should not be left up to the
kernel to handle that.
Using the ti,external-control property allows specifying this use-case.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This switches a few interrupt definitions that were using
GPIO_ACTIVE_HIGH as IRQ type, which is invalid.
This is mostly a cosmetic change, that doesn't affect any driver.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Card insertion and removal currently goes undetected. AFAIK there's no
way to generate interrupts on card changes in this slot, so use polling.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Current U-Boot enables the display already. Marking the regulator as
enabled on boot fixes sporadic panel initialization failures.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Tested-by: Misha Komarovskiy <zombah@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now with the new V1.1A HW card detect being implemented update resp.
compatibility information.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Configure Apalis MMC1 D6 GPIO on SDMMC3_CLK_LB_IN as reserved function
without any pull-up/down.
Configure GPIO_PV2 as SD1_CD# according to latest V1.1 HW.
Leave SDMMC3_CLK_LB_OUT muxed as SDMMC3 with output driver enabled aka
not tristated and input driver enabled as well as it features some
magic properties even though the external loopback is disabled and the
internal loopback used as per SDMMC_VENDOR_MISC_CNTRL_0 register's
SDMMC_SPARE1 bits being set to 0xfffd according to the TRM! This pin is
now a not-connect on V1.1 HW in order to avoid any interference.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 7f107887d1 ("ARM: dts: imx: Remove skeleton.dtsi") causes boot
issues when the bootloader does not create a 'chosen' node if such node
is not present in the dtb.
The reason for the boot failure is well explained by Javier Martinez
Canillas: "the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info."
, so pass an empty 'chosen' node to fix the boot problem.
This issue has been seen in the kernelci reports with Barebox as
bootloader.
Also pass the 'memory' node in order to fix boot issues on the SolidRun
iMX6 platforms.
Fixes: 7f107887d1 ("ARM: dts: imx: Remove skeleton.dtsi")
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
