We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
Fixes: 6d8a019614 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/db2c80108286cfd108adb05bad52138b78d7c3a7.1650673655.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The list_for_each_entry_safe() macro saves the current item (n) and
the item after (n+1), so that n can be safely removed without
corrupting the list. However, when traversing the list and removing
items using gadget giveback, the DWC3 lock is briefly released,
allowing other routines to execute. There is a situation where, while
items are being removed from the cancelled_list using
dwc3_gadget_ep_cleanup_cancelled_requests(), the pullup disable
routine is running in parallel (due to UDC unbind). As the cleanup
routine removes n, and the pullup disable removes n+1, once the
cleanup retakes the DWC3 lock, it references a request who was already
removed/handled. With list debug enabled, this leads to a panic.
Ensure all instances of the macro are replaced where gadget giveback
is used.
Example call stack:
Thread#1:
__dwc3_gadget_ep_set_halt() - CLEAR HALT
-> dwc3_gadget_ep_cleanup_cancelled_requests()
->list_for_each_entry_safe()
->dwc3_gadget_giveback(n)
->dwc3_gadget_del_and_unmap_request()- n deleted[cancelled_list]
->spin_unlock
->Thread#2 executes
...
->dwc3_gadget_giveback(n+1)
->Already removed!
Thread#2:
dwc3_gadget_pullup()
->waiting for dwc3 spin_lock
...
->Thread#1 released lock
->dwc3_stop_active_transfers()
->dwc3_remove_requests()
->fetches n+1 item from cancelled_list (n removed by Thread#1)
->dwc3_gadget_giveback()
->dwc3_gadget_del_and_unmap_request()- n+1 deleted[cancelled_list]
->spin_unlock
Fixes: d4f1afe5e8 ("usb: dwc3: gadget: move requests to cancelled_list")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220414183521.23451-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_ep_clear_halt() API can be called from the function driver, and
translates to dwc3_gadget_ep_set_halt(). This routine is shared with when
the host issues a clear feature ENDPOINT_HALT, and is differentiated by the
protocol argument. If the following sequence occurs, there can be a
situation where the delayed_status flag is improperly cleared for the wrong
SETUP transaction:
1. Vendor specific control transfer returns USB_GADGET_DELAYED_STATUS.
2. DWC3 gadget sets dwc->delayed_status to '1'.
3. Another function driver issues a usb_ep_clear_halt() call.
4. DWC3 gadget issues dwc3_stop_active_transfer() and sets
DWC3_EP_PENDING_CLEAR_STALL.
5. EP command complete interrupt triggers for the end transfer, and
dwc3_ep0_send_delayed_status() is allowed to run, as delayed_status
is '1' due to step#1.
6. STATUS phase is sent, and delayed_status is cleared.
7. Vendor specific control transfer is finished being handled, and issues
usb_composite_setup_continue(). This results in queuing of a data
phase.
Cache the protocol flag so that DWC3 gadget is aware of when the clear halt
is due to a SETUP request from the host versus when it is sourced from a
function driver. This allows for the EP command complete interrupt to know
if it needs to issue a delayed status phase.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220414073902.21960-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two kerneldoc comments in gadget.c have excess function parameter description or wrong
prototype name and one kerneldoc comment in core.c has an excess function parameter
description, resulting in these three doc-build warnings:
1. ./drivers/usb/dwc3/gadget.c:675: warning: Excess function parameter
'nfifos' description in 'dwc3_gadget_calc_tx_fifo_size'
2. ./drivers/usb/dwc3/gadget.c:700: warning: expecting prototype for
dwc3_gadget_clear_tx_fifo_size(). Prototype was for dwc3_gadget_clear_tx_fifos()
instead
3. ./drivers/usb/dwc3/core.c:347: warning: Excess function parameter 'ref_clk_per'
description in 'dwc3_ref_clk_period'
Fix the warnings by correcting the prototype name and removing excess parameter descriptions.
Signed-off-by: Kushagra Verma <kushagra765@outlook.com>
Link: https://lore.kernel.org/r/SI2PR01MB392995043CACD80884A13764F81C9@SI2PR01MB3929.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the PHY controller node has a "port" dwc3 tries to find an
extcon device even when "usb-role-switch" is present. This happens
because dwc3_get_extcon() sees that "port" node and then calls
extcon_find_edev_by_node() which will always return EPROBE_DEFER
in that case.
On the other hand, even if an extcon was present and dwc3_get_extcon()
was successful it would still be ignored in favor of "usb-role-switch".
Let's just first check if "usb-role-switch" is configured in the device
tree and directly use it instead and only try to look for an extcon
device otherwise.
Fixes: 8a0a137997 ("usb: dwc3: Registering a role switch in the DRD code.")
Cc: stable <stable@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20220411155300.9766-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 33fb697ec7 ("usb: dwc3: Get clocks individually") moved from
the clk_bulk api to individual clocks, following the snps,dwc3.yaml
dt-binding for clock names.
Unfortunately the rk3328 (and upcoming rk356x support) use the
rockchip,dwc3.yaml which has different clock names, which are common on
devices using the glue layer.
The rk3328 does not use a glue layer, but attaches directly to the dwc3
core driver.
The offending patch series failed to account for this, thus dwc3 was
broken on rk3328.
To retain backwards compatibility with rk3328 device trees we must also
check for the alternate clock names.
Fixes: 33fb697ec7 ("usb: dwc3: Get clocks individually")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220409152116.3834354-1-pgwipeout@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a Setup packet is received but yet to DMA out, the controller will
not process the End Transfer command of any endpoint. Polling of its
DEPCMD.CmdAct may block setting up TRB for Setup packet, causing a
command timeout.
This may occur if the driver doesn’t service the completion interrupt of
the control status stage yet due to system latency, then it won’t
prepare TRB and start the transfer for the next Setup Stage. To the host
side, the control transfer had completed, and the host can send a new
Setup packet at this point.
In the meanwhile, if the driver receives an async call to dequeue a
request (triggering End Transfer) to any endpoint, then the driver will
service that End transfer first, blocking the control status stage
completion handler. Since no TRB is available for the Setup stage, the
Setup packet can’t be DMA’ed out and the End Transfer gets hung.
The driver must not block setting up of the Setup stage. So track and
only issue the End Transfer command only when there’s Setup TRB prepared
so that the controller can DMA out the Setup packet. Delay the End
transfer command if there's no Setup TRB available. This is applicable to
all DWC_usb3x IPs.
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220309205402.4467-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX8MP glue layer has support for the following flags:
* over-current polarity
* PWR pad polarity
* controlling PPC flag in HCCPARAMS register
* permanent port attach for usb2 & usb3 port
Allow setting these flags by supporting specific flags in the glue node.
In order to get this to work an additional IORESOURCE_MEM and clock is
necessary. For backward compatibility this is purely optional.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220218152707.2198357-4-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here, and it resolves a merge conflict in:
drivers/usb/dwc3/dwc3-pci.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Link: https://lkml.kernel.org/r/c2a64979-73d1-2c22-e048-c275c9f81558@samsung.com
Fixes: e5f68b4a3e ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <stable@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/Yg/YPejVQH3KkRVd@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Android x86 tablets with a Bay Trail (BYT) SoC and a Crystal Cove
PMIC, which does not support charger-detection, rely on the TUSB1211 phy
for charger-detection.
Windows tablets with the same SoC + PMIC often use an extra chip for
charger-detection like the FSA831A. But since on Android tablets
the designers already need to add a TUSB1211 phy to support device/gadget
mode the phy is used to do charger-detection instead.
These Android x86 tablets can be identified by the unique combination of
a Bay Trail SoC (already checked for by PCI-ids) + a Crystal Cove PMIC +
not using the standard ACPI battery and ac drivers. Where as on Windows
tablets the standard ACPI battery and ac drivers will be used on BYT
boards with a Crystal Cove PMIC.
Set a special kernel-internal (so not part of the dt-bindings)
"linux,phy_charger_detect" property on these boards, which tells the
tusb1210 driver to enable charger-detection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0082698b6 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
fixed an issue where ULPI transfers would timeout if any requests where
send to the phy sometime after init, giving it enough time to auto-suspend.
Commit e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend
regression") changed the behavior to instead of clearing the
DWC3_GUSB2PHYCFG_SUSPHY bit, add an extra sleep when it is set.
But on Bay Trail devices, when phy_set_mode() gets called during init,
this leads to errors like these:
[ 28.451522] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
[ 28.464089] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
Add "snps,dis_u2_susphy_quirk" to the settings for Bay Trail devices to
fix this. This restores the old behavior for Bay Trail devices, since
previously the DWC3_GUSB2PHYCFG_SUSPHY bit would get cleared on the first
ulpi_read/_write() and then was never set again.
Fixes: e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression")
Cc: stable@kernel.org
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CPU re-ordering on write instructions, there might
be a chance that the HWO is set before the TRB is updated
with the new mapped buffer address.
And in the case where core is processing a list of TRBs
it is possible that it fetched the TRBs when the HWO is set
but before the buffer address is updated.
Prevent this by adding a memory barrier before the HWO
is updated to ensure that the core always process the
updated TRBs.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1644207958-18287-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GUCTL.REFCLKPER can only account for clock frequencies with integer
periods. To address this, program REFCLK_FLADJ with the relative error
caused by period truncation. The formula given in the register reference
has been rearranged to allow calculation based on rate (instead of
period), and to allow for fixed-point arithmetic.
Additionally, calculate a value for 240MHZDECR. This configures a
simulated 240Mhz clock using a counter with one fractional bit (PLS1).
This register is programmed only for versions >= 2.50a, since this is
the check also used by commit db2be4e9e3 ("usb: dwc3: Add frame length
adjustment quirk").
Tested-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127200636.1456175-5-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that the PIPE clock should not be selected when only USB 2.0
is being used in the design and no USB 3.0 reference clock is used.
Also, the core resets are not required if a USB3 PHY is not in use, and
will break things if USB3 is actually used but the PHY entry is not
listed in the device tree.
Skip core resets and register settings that are only required for
USB3 mode when no USB3 PHY is specified in the device tree.
Fixes: 84770f028f ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-2-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys introduced a new enhancement to DWC_usb32 called Multi-Stream
Transfer (MST) to improve bulk streams performance for SuperSpeed and
SuperSpeed Plus. This enhancement allows the controller to look ahead
and process multiple bulk streams.
Previously, to initiate a bulk stream transfer, the driver has to issue
Start Transfer command and wait for the stream to complete before
initiating a new stream. As a result, the controller does not process
TRBs beyond a single stream. With the enhancement, as long as there are
new requests, the dwc3 driver can keep preparing new TRBs and the
controller can keep caching and processing them without waiting for the
transfer completion.
The programming flow is similar to regular bulk endpoint with a few
additional rules:
1) Chained TRBs of the same stream must have a matching stream ID
2) The last TRB of a stream must have CHN=0
3) All the TRBs with LST=0 must have CSP=1
Depends on the application and usage, internal tests show significant
performance improvement in UASP transfers with this enhancement.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cd9c7a8bf11f790983ac546222dd114893f16b3a.1638242424.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cefdd52fa0.
On sc7180-trogdor class devices with 'fw_devlink=permissive' and KASAN
enabled, you'll see a Use-After-Free reported at bootup.
The root of the problem is that dwc3_qcom_of_register_core() is adding
a devm-allocated "tx-fifo-resize" property to its device tree node
using of_add_property().
The issue is that of_add_property() makes a _permanent_ addition to
the device tree that lasts until reboot. That means allocating memory
for the property using "devm" managed memory is a terrible idea since
that memory will be freed upon probe deferral or device unbinding.
Let's revert the patch since the system is still functional without
it. The fact that of_add_property() makes a permanent change is extra
fodder for those folks who were aruging that the device tree isn't
really the right way to pass information between parts of the
driver. It is an exercise left to the reader to submit a patch
re-adding the new feature in a way that makes everyone happier.
Fixes: cefdd52fa0 ("usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211207094327.1.Ie3cde3443039342e2963262a4c3ac36dc2c08b30@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
