This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port. It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement flash_update() devlink op for the line card devlink instance
to allow user to update line card gearbox FW using MDDT register
and mlxfw.
Example:
$ devlink dev flash auxiliary/mlxsw_core.lc.0 file mellanox/fw-AGB-rel-19_2010_1312-022-EVB.mfa2
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use tunneled MGIR to obtain PSID of line card device and extend
device_info_get() op to fill up the info with that.
Example:
$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
versions:
fixed:
hw.revision 0
fw.psid MT_0000000749
running:
ini.version 4
fw 19.2010.1312
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDDT register allows to deliver query and request messages (PRM
registers, commands) to a DownStream device.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case the line card is active, go over all possible existing
devices (gearboxes) on it and expose FW version of the flashable one.
Example:
$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
versions:
fixed:
hw.revision 0
running:
ini.version 4
fw 19.2010.1312
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend existing MDDQ register by possibility to query information about
devices residing on a line card.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement info_get() to expose HW revision of a linecard and loaded INI
version.
Example:
$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
versions:
fixed:
hw.revision 0
running:
ini.version 4
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to be eventually able to expose line card gearbox version and
possibility to flash FW, model the line card as a separate device on
auxiliary bus.
Add the auxiliary device for provisioned line card in order to be able
to expose provisioned line card info over devlink dev info. When the
line card becomes active, there may be other additional info added to
the output.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently loopback test is failiing due to the error returned from
ice_vsi_vlan_setup(). Skip calling it when preparing loopback VSI.
Fixes: 0e674aeb0b ("ice: Add handler for ethtool selftest")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tx side sets EOP and RS bits on descriptors to indicate that a
particular descriptor is the last one and needs to generate an irq when
it was sent. These bits should not be checked on completion path
regardless whether it's the Tx or the Rx. DD bit serves this purpose and
it indicates that a particular descriptor is either for Rx or was
successfully Txed. EOF is also set as loopback test does not xmit
fragmented frames.
Look at (DD | EOF) bits setting in ice_lbtest_receive_frames() instead
of EOP and RS pair.
Fixes: 0e674aeb0b ("ice: Add handler for ethtool selftest")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver currently does not allow two VSIs in the same PF domain
to have the same unicast MAC address. This is incorrect in the sense
that a policy decision is being made in the driver when it must be
left to the user. This approach was causing issues when rebooting
the system with VFs spawned not being able to change their MAC addresses.
Such errors were present in dmesg:
[ 7921.068237] ice 0000:b6:00.2 ens2f2: Unicast MAC 6a:0d:e4:70:ca:d1 already
exists on this PF. Preventing setting VF 7 unicast MAC address to 6a:0d:e4:70:ca:d1
Fix that by removing this restriction. Doing this also allows
us to remove some additional code that's checking if a unicast MAC
filter already exists.
Fixes: 47ebc7b024 ("ice: Check if unicast MAC exists before setting VF MAC")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix checksum offload on VXLAN tunnels.
In case, when mpls protocol is not used, set l4 header to transport
header of skb. This fixes case, when user tries to offload checksums
of VXLAN tunneled traffic.
Steps for reproduction (requires link partner with tunnels):
ip l s enp130s0f0 up
ip a f enp130s0f0
ip a a 10.10.110.2/24 dev enp130s0f0
ip l s enp130s0f0 mtu 1600
ip link add vxlan12_sut type vxlan id 12 group 238.168.100.100 dev enp130s0f0 dstport 4789
ip l s vxlan12_sut up
ip a a 20.10.110.2/24 dev vxlan12_sut
iperf3 -c 20.10.110.1 #should connect
Offload params: td_offset, cd_tunnel_params were
corrupted, due to l4 header pointing wrong address. NIC would then drop
those packets internally, due to incorrect TX descriptor data,
which increased GLV_TEPC register.
Fixes: 69e66c04c6 ("ice: Add mpls+tso support")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Legacy VLAN implementation allows for untrusted VF to have 8 VLAN
filters, not counting VLAN 0 filters. Current VLAN_V2 implementation
lowers available filters for VF, by counting in VLAN 0 filter for both
TPIDs.
Fix this by counting only non zero VLAN filters.
Without this patch, untrusted VF would not be able to access 8 VLAN
filters.
Fixes: cc71de8fa1 ("ice: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for creating PPPoE filters in switchdev mode. Add support
for parsing PPPoE and PPP-specific tc options: pppoe_sid and ppp_proto.
Example filter:
tc filter add dev $PF1 ingress protocol ppp_ses prio 1 flower pppoe_sid \
1234 ppp_proto ip skip_sw action mirred egress redirect dev $VF1_PR
Changes in iproute2 are required to use the new fields.
ICE COMMS DDP package is required to create a filter as it contains PPPoE
profiles. Added a warning message when loaded DDP package does not contain
required profiles.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Check the mask for non-zero value before installing tc filters
for L4 source and destination ports. Otherwise installing a
filter for source port installs destination port too and
vice-versa.
Fixes: 1d4d9e42c2 ("octeontx2-pf: Add tc flower hardware offload on ingress traffic")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NIX_AF_TLXX_PIR/CIR register format has changed from OcteonTx2
to CN10K. CN10K supports larger burst size. Fix burst exponent
and burst mantissa configuration for CN10K.
Also fixed 'maxrate' from u32 to u64 since 'police.rate_bytes_ps'
passed by stack is also u64.
Fixes: e638a83f16 ("octeontx2-pf: TC_MATCHALL egress ratelimiting offload")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Check the mask for non-zero value before installing tc filters
for L4 source and destination ports. Otherwise installing a
filter for source port installs destination port too and
vice-versa.
Fixes: 1d4d9e42c2 ("octeontx2-pf: Add tc flower hardware offload on ingress traffic")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NIX_AF_TLXX_PIR/CIR register format has changed from OcteonTx2
to CN10K. CN10K supports larger burst size. Fix burst exponent
and burst mantissa configuration for CN10K.
Also fixed 'maxrate' from u32 to u64 since 'police.rate_bytes_ps'
passed by stack is also u64.
Fixes: e638a83f16 ("octeontx2-pf: TC_MATCHALL egress ratelimiting offload")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
DRV_VERSION is a leftover from when the driver was an out of tree
module. The driver version was never incremented despite of the
numerous changes made since it was mainstreamed. Keeping an
unmaintained driver version number makes no sense. Remove it and rely
on the kernel version instead.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220726082707.58758-11-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove the limitation where the interface needs to be down to change
MTU by releasing and opening the stmmac driver to set the new MTU.
Also call the set_filter function to correctly init the port.
This permits to remove the EBUSY error while the ethernet port is
running permitting a correct MTU change if for example a DSA request
a MTU change for a switch CPU port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rework the driver to generate the stmmac dma_conf before stmmac_open.
This permits a function to first check if it's possible to allocate a
new dma_config and then pass it directly to __stmmac_open and "open" the
interface with the new configuration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move dma buf conf to dedicated struct. This in preparation for code
rework that will permit to allocate separate dma_conf without affecting
the priv struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Disable all queues and disconnect before tx_disable in stmmac_release to
prevent a corner case where packet may be still queued at the same time
tx_disable is called resulting in kernel panic if some packet still has
to be processed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move queue reset to dedicated functions. This aside from a simple
cleanup is also required to allocate a dma conf without resetting the tx
queue while the device is temporarily detached as now the reset is not
part of the dma init function and can be done later in the code flow.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kalle Valo says:
====================
wireless-next patches for v5.20
Third set of patches for v5.20. MLO work continues and we have a lot
of stack changes due to that, including driver API changes. Not much
driver patches except on mt76.
Major changes:
cfg80211/mac80211
- more prepartion for Wi-Fi 7 Multi-Link Operation (MLO) support,
works with one link now
- align with IEEE Draft P802.11be_D2.0
- hardware timestamps for receive and transmit
mt76
- preparation for new chipset support
- ACPI SAR support
* tag 'wireless-next-2022-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (254 commits)
wifi: mac80211: fix link data leak
wifi: mac80211: mlme: fix disassoc with MLO
wifi: mac80211: add macros to loop over active links
wifi: mac80211: remove erroneous sband/link validation
wifi: mac80211: mlme: transmit assoc frame with address translation
wifi: mac80211: verify link addresses are different
wifi: mac80211: rx: track link in RX data
wifi: mac80211: optionally implement MLO multicast TX
wifi: mac80211: expand ieee80211_mgmt_tx() for MLO
wifi: nl80211: add MLO link ID to the NL80211_CMD_FRAME TX API
wifi: mac80211: report link ID to cfg80211 on mgmt RX
wifi: cfg80211: report link ID in NL80211_CMD_FRAME
wifi: mac80211: add hardware timestamps for RX and TX
wifi: cfg80211: add hardware timestamps to frame RX info
wifi: cfg80211/nl80211: move rx management data into a struct
wifi: cfg80211: add a function for reporting TX status with hardware timestamps
wifi: nl80211: add RX and TX timestamp attributes
wifi: ieee80211: add helper functions for detecting TM/FTM frames
wifi: mac80211_hwsim: handle links for wmediumd/virtio
wifi: mac80211: sta_info: fix link_sta insertion
...
====================
Link: https://lore.kernel.org/r/20220725174547.EA465C341C6@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2022-07-22
This series contains updates to i40e and iavf drivers.
Przemyslaw adds a helper function for determining whether TC MQPRIO is
enabled for i40e.
Avinash utilizes the driver's bookkeeping of filters to check for
duplicate filter before sending the request to the PF for iavf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A typical flow offload scenario for OpenWrt users is routed traffic
received by the wan interface that is redirected to a wlan device
belonging to the lan bridge. Current implementation fails to
fill wdma offload info in mtk_flow_get_wdma_info() since odev device is
the local bridge. Fix the issue running dev_fill_forward_path routine in
mtk_flow_get_wdma_info in order to identify the wlan device.
Tested-by: Paolo Valerio <pvalerio@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_ptp_phc_adjfreq() configures MTUTC register to adjust
hardware frequency by a given value.
This configuration will be same for Spectrum-2. In preparation for
Spectrum-2 PTP support, rename the function to not be Spectrum-1 specific.
Later, it will be used for Spectrum-2 also.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-1 and Spectrum-2 differ in their time stamping capabilities.
The former can be configured to time stamp only a subset of received PTP
events (e.g., only Sync), whereas the latter will time stamp all PTP
events or none.
In preparation for Spectrum-2 PTP support, rename the function that
parses the hardware time stamping configuration upon %SIOCSHWTSTAMP to
be Spectrum-1 specific.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is one shared structure that holds the required
structures for PTP clock. Most of the existing fields are relevant only
for Spectrum-1 (cycles, timecounter, and more). Rename the structure to
be specific for Spectrum-1 and align the existing code. Add a common
structure which includes the structures which will be used also for
Spectrum-2. This structure will be returned from clock_init() operation,
as the definition is shared between all ASICs' operations.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
