In full monitor mode, monitor destination ring is read before monitor
status ring. mon_dst_ring has ppdu id, reap till the end of PPDU. Add
all the MPDUs to list. Start processing the status ring, if PPDU id in
status ring is lagging behind, reap the status ring, once the PPDU ID
matches, deliver the MSDU to upper layer. If status PPDU id leading,
reap the mon_dst_ring.
The advantage with full monitor mode is hardware has status buffers
available for all the MPDUs in mon_dst_ring, which makes it possible
to deliver more frames to be seen on sniffer.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-4-git-send-email-akolli@codeaurora.org
In builds with -Warray-bounds, casts from smaller objects to larger
objects will produce warnings. These can be overly conservative, but since
-Warray-bounds has been finding legitimate bugs, it is desirable to turn
it on globally. Instead of casting a u32 to a larger object, redefine
the u32 portion of the header to a separate struct that can be used for
both u32 operations and the distinct header fields. Silences this warning:
drivers/net/wireless/ath/ath6kl/htc_mbox.c: In function 'htc_wait_for_ctrl_msg':
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2275:20: error: array subscript 'struct htc_frame_hdr[0]' is partly outside array bounds of 'u32[1]' {aka 'unsigned int[1]'} [-Werror=array-bounds]
2275 | if (htc_hdr->eid != ENDPOINT_0)
| ^~
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2264:13: note: while referencing 'look_ahead'
2264 | u32 look_ahead;
| ^~~~~~~~~~
This change results in no executable instruction differences.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207063538.2767954-1-keescook@chromium.org
Currently mac80211 will send 3 scan request for each scan of WCN6855,
they are 2.4 GHz/5 GHz/6 GHz band scan. Firmware of WCN6855 will
cache the RNR IE(Reduced Neighbor Report element) which exist in the
beacon of 2.4 GHz/5 GHz of the AP which is co-located with 6 GHz,
and then use the cache to scan in 6 GHz band scan if the 6 GHz scan
is in the same scan with the 2.4 GHz/5 GHz band, this will helpful to
search more AP of 6 GHz. Also it will decrease the time cost of scan
because firmware will use dual-band scan for the 2.4 GHz/5 GHz, it
means the 2.4 GHz and 5 GHz scans are doing simultaneously.
Set the flag IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS for WCN6855 since
it supports 2.4 GHz/5 GHz/6 GHz and it is single pdev which means
all the 2.4 GHz/5 GHz/6 GHz exist in the same wiphy/ieee80211_hw.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129101309.2931-1-quic_wgong@quicinc.com
If cfg80211 is providing extraie's for a scanning process then ath11k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This
section can have a (payload) length up to 65535 bytes because the
WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and
could have created a scan request which cannot be parsed correctly by the
firmware.
But the bigger problem was the allocation of the buffer. It has to align
the TLV sections by 4 bytes. But the code was using an u8 to store the
newly calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual code
to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a QCA Milan card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Cc: stable@vger.kernel.org
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207142913.1734635-1-sven@narfation.org
While running stress tests in roaming scenarios (switching ap's every 5
seconds, we discovered a issue which leads to tx hangings of exactly 5
seconds while or after scanning for new accesspoints. We found out that
this hanging is triggered by ath10k_mac_wait_tx_complete since the
empty_tx_wq was not wake when the num_tx_pending counter reaches zero.
To fix this, we simply move the wake_up call to htt_tx_dec_pending,
since this call was missed on several locations within the ath10k code.
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20210505085806.11474-1-s.gottschall@dd-wrt.com
In ath11k, tx of management packet is doing in a work queue. Sometimes
the workqueue does not finish tx immediately, then it lead after the next
step of vdev delete finished, it start to send the management packet to
firmware and lead firmware crash.
ieee80211_set_disassoc() have logic of ieee80211_flush_queues() after
it send_deauth_disassoc() to ath11k, its purpose is make sure the
deauth was actually sent, so it need to change ath11k to match the
purpose of mac80211.
To address these issue wait for tx mgmt as well as tx data packets.
dmesg log of connect/disconnect to AP:
[ 307.522226] wls1: authenticate with 62:66:e4:e9:6a:a9
[ 307.586565] wls1: send auth to 62:66:e4:e9:6a:a9 (try 1/3)
[ 307.586581] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 307.586922] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 307.590179] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 307.590181] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 307.598699] wls1: authenticated
[ 307.599483] wls1: associate with 62:66:e4:e9:6a:a9 (try 1/3)
[ 307.599506] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 307.599519] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 307.603059] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 307.603063] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 307.637105] wls1: associated
[ 317.365239] wls1: deauthenticating from 62:66:e4:e9:6a:a9 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 317.368104] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 317.372622] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 317.378320] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 317.378330] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 317.378359] ath11k_pci 0000:05:00.0: mac mgmt tx flush mgmt pending 0
[ 317.421066] ath11k_pci 0000:05:00.0: mac mgmt tx flush mgmt pending 0
[ 317.421427] ath11k_pci 0000:05:00.0: mac remove interface (vdev 0)
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211202063705.14321-1-quic_wgong@quicinc.com
Kernel test robot reported:drivers/net/wireless/ath/wcn36xx/smd.c:943:33:
sparse: sparse: cast truncates bits from constant value (780 becomes 80)
The 'channels' field is not a simple u8 array but an array of
channel_params. Using sizeof for retrieving the max number of
channels is then wrong.
In practice, it was not an issue, because the sizeof returned
value is 780, which is truncated in min_t (u8) to 80, which is
the value we expect...
Fix that properly using ARRAY_SIZE instead of sizeof.
Fixes: d707f812bb ("wcn36xx: Channel list update before hardware scan")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638435732-14657-1-git-send-email-loic.poulain@linaro.org
Add handler for WMI_11D_NEW_COUNTRY_EVENTID, WMI_11D_SCAN_START_CMDID,
WMI_11D_SCAN_STOP_CMDID.
After vdev create for STATION, send WMI_11D_SCAN_START_CMDID to firmware
and wait firmware complete it, the scan from mac80211 also need to wait
the 11d scan finished, and send WMI_11D_SCAN_STOP_CMDID to firmware
before vdev delete for STATION.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211201071745.17746-4-quic_wgong@quicinc.com
Currently there are about 60 channels for 6 GHz, then the size of
chan_list in struct scan_req_params which is 40 is not enough to
fill all the channel list of 6 GHz.
Use dynamic memory to save the channel list of scan.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129110939.15711-1-quic_wgong@quicinc.com
bdf_type for caldata in QMI_WLANFW_BDF_DOWNLOAD_REQ_V01 is wrongly
sent as 1. But, expected bdf_type value for caldata and EEPROM is 2 and 3
respectively. It leads to firmware crash. Fix ath11k_qmi_file_type enum
values.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Fixes: 336e7b53c8 ("ath11k: clean up BDF download functions")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638182754-18408-1-git-send-email-quic_seevalam@quicinc.com
Ath11k fails to probe WCN6855 hw2.1 chip:
[ 6.983821] ath11k_pci 0000:06:00.0: enabling device (0000 -> 0002)
[ 6.983841] ath11k_pci 0000:06:00.0: Unsupported WCN6855 SOC hardware version: 18 17
This is caused by the wrong bit mask setting of hardware major version:
for QCA6390/QCN6855, it should be BIT8-11, not BIT8-16, so change the
definition to GENMASK(11, 8).
Also, add a separate entry for WCN6855 hw2.1 in ath11k_hw_params.
Please note that currently WCN6855 hw2.1 shares the same firmwares
as hw2.0, so users of this chip need to create a symlink as below:
ln -s hw2.0 hw2.1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Fixes: 18ac1665e7 ("ath11k: pci: check TCSR_SOC_HW_VERSION")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129025613.21594-1-quic_bqiang@quicinc.com
This patch changes mac80211 rate control for the ath9k driver. The rate lookup
per packet is changed from legacy usage of ieee80211_get_tx_rates() to the new
rate table based lookup in struct ieee80211_sta->rates.
The most recent rate control API, introduced with commit 0d528d85c5
("mac80211: improve the rate control API"), allows drivers to directly get
rates from ieee80211_sta->rates. This is not used by every driver yet, the
translation/merge is currently performed in ieee80211_get_tx_rates. This patch
changes the behaviour and avoids the call to ieee80211_get_tx_rates and
subsequent calls. ath9k now directly reads rates from sta->rates into its rate
table. Cause ath9k does not expect rate selection in SKB->CB, the table merge
does not consider rate array in SKB->CB except for the first entry (used for
probing).
Tested with a 8devices Rambutan with QCA9558 SoC by performing two runs, one
without the patch and one with. Generated traffic between AP and multiple STAs
in each run, measured throughput and captured rc_stats. Comparison of both
runs resulted in same rate selection and no performance loss or other negative
effects.
Co-developed-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211128090753.958-1-jelonek.jonas@gmail.com
On an imx6dl-pico-pi board with a QCA9377 SDIO chip, simply trying to
connect via ssh to another machine causes:
[ 55.824159] ath10k_sdio mmc1:0001:1: failed to transmit packet, dropping: -12
[ 55.832169] ath10k_sdio mmc1:0001:1: failed to submit frame: -12
[ 55.838529] ath10k_sdio mmc1:0001:1: failed to push frame: -12
[ 55.905863] ath10k_sdio mmc1:0001:1: failed to transmit packet, dropping: -12
[ 55.913650] ath10k_sdio mmc1:0001:1: failed to submit frame: -12
[ 55.919887] ath10k_sdio mmc1:0001:1: failed to push frame: -12
, leading to an ssh connection failure.
One user inspected the size of frames on Wireshark and reported
the followig:
"I was able to narrow the issue down to the mtu. If I set the mtu for
the wlan0 device to 1486 instead of 1500, the issue does not happen.
The size of frames that I see on Wireshark is exactly 1500 after
setting it to 1486."
Clearing the HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE avoids the problem and
the ssh command works successfully after that.
Introduce a 'credit_size_workaround' field to ath10k_hw_params for
the QCA9377 SDIO, so that the HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE
is not set in this case.
Tested with QCA9377 SDIO with firmware WLAN.TF.1.1.1-00061-QCATFSWPZ-1.
Fixes: 2f918ea986 ("ath10k: enable alt data of TX path for sdio")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211124131047.713756-1-festevam@denx.de
Currently 'ar' reference is not added in skb_cb during
WMI mgmt tx. Though this is generally not used during tx completion
callbacks, on interface removal the remaining idr cleanup callback
uses the ar ptr from skb_cb from mgmt txmgmt_idr. Hence
fill them during tx call for proper usage.
Also free the skb which is missing currently in these
callbacks.
Crash_info:
[19282.489476] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[19282.489515] pgd = 91eb8000
[19282.496702] [00000000] *pgd=00000000
[19282.502524] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[19282.783728] PC is at ath11k_mac_vif_txmgmt_idr_remove+0x28/0xd8 [ath11k]
[19282.789170] LR is at idr_for_each+0xa0/0xc8
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637832614-13831-1-git-send-email-quic_srirrama@quicinc.com
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_after() so memset() doesn't get confused about writing
beyond the destination member that is intended to be the starting point
of zeroing through the end of the struct.
Additionally fix the common helper, ieee80211_tx_info_clear_status(),
which was not clearing ack_signal, but the open-coded versions
did. Johannes Berg points out this bug was introduced by commit
e3e1a0bcb3 ("mac80211: reduce IEEE80211_TX_MAX_RATES") but was harmless.
Also drops the associated unneeded BUILD_BUG_ON()s, and adds a note to
carl9170 about usage.
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Christian Lamparter <chunkeey@gmail.com> [both CARL9170+P54USB on real HW]
Link: https://lore.kernel.org/r/20211118203839.1289276-1-keescook@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since firmware uses its own sequence number counters, we need to
use firmware number as well when mac80211 generates the ADD_BA
request packet. Indeed the firmware sequence counters tend to
slightly drift from the mac80211 ones because of firmware offload
features like ARP responses. This causes the starting sequence
number field of the ADD_BA request to be unaligned, and can possibly
cause issues with strict/picky APs.
To fix this, we retrieve the current firmware sequence number for
a given TID through the smd_trigger_ba API, and use that number as
replacement of the mac80211 starting sequence number.
This change also ensures that any issue in the smd *ba procedures
will cause the ba action to properly fail, and remove useless call
to smd_trigger_ba() from IEEE80211_AMPDU_RX_START.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637604251-11763-1-git-send-email-loic.poulain@linaro.org
CE interrupt configuration uses host ce parameters to assign/free
interrupts. Use host ce parameters to enable/disable interrupts.
This patch fixes below BUG,
BUG: KASAN: global-out-of-bounds in 0xffffffbffdfb035c at addr
ffffffbffde6eeac
Read of size 4 by task kworker/u8:2/132
Address belongs to variable ath11k_core_qmi_firmware_ready+0x1b0/0x5bc [ath11k]
OOB is due to ath11k_ahb_ce_irqs_enable() iterates ce_count(which is 12)
times and accessing 12th element in target_ce_config
(which has only 11 elements) from ath11k_ahb_ce_irq_enable().
With this change host ce configs are used to enable/disable interrupts.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00471-QCAHKSWPL_SILICONZ-1
Fixes: 967c1d1131 ("ath11k: move target ce configs to hw_params")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249558-12793-1-git-send-email-akolli@codeaurora.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_startat() so memset() doesn't get confused about writing
beyond the destination member that is intended to be the starting point
of zeroing through the end of the struct. Additionally split up a later
field-spanning memset() so that memset() can reason about the size.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118202416.1286046-1-keescook@chromium.org
This reverts commit 46e46db313. Mark reported
that it breaks QCA6390 hw2.0 on Dell XPS 13 9310:
[ 5.537034] ath11k_pci 0000:72:00.0: chip_id 0x0 chip_family 0xb board_id 0xff soc_id 0xffffffff
[ 5.537038] ath11k_pci 0000:72:00.0: fw_version 0x101c06cc fw_build_timestamp 2020-06-24 19:50 fw_build_id
[ 5.537236] ath11k_pci 0000:72:00.0: failed to fetch board data for bus=pci,qmi-chip-id=0,qmi-board-id=255,variant=DE_1901 from ath11k/QCA6390/hw2.0/board-2.bin
[ 5.537255] ath11k_pci 0000:72:00.0: failed to fetch board-2.bin or board.bin from QCA6390/hw2.0
[ 5.537257] ath11k_pci 0000:72:00.0: qmi failed to fetch board file: -2
[ 5.537258] ath11k_pci 0000:72:00.0: failed to load board data file: -2
So we need to back to the drawing board and implement it so that backwards
compatiblity is not broken.
Reported-by: Mark Herbert <mark.herbert42@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211124094316.9096-1-kvalo@codeaurora.org
In HE monitor capture, HAL_TLV_STATUS_PPDU_DONE is received
on processing multiple skb. Do not clear the ppdu_info
till the HAL_TLV_STATUS_PPDU_DONE is received.
This fixes below warning and packet drops in monitor mode.
"Rate marked as an HE rate but data is invalid: MCS: 6, NSS: 0"
WARNING: at
PC is at ieee80211_rx_napi+0x624/0x840 [mac80211]
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01693-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249433-10316-1-git-send-email-akolli@codeaurora.org
The ath11k driver currently sends vdev down to the firmware before
updating the channel context, which is followed by a vdev restart
command.
Sending vdev down is not required before sending a vdev restart,
because the firmware internally does vdev down when ath11k sends
a vdev restart command.
Firmware will happen crash while channel switch without this change.
Hence skip the vdev down command sending when updating the channel
context and then fix the firmware crash issue.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095901.8271-1-quic_wgong@quicinc.com
The pdev id is set to 0 for single pdev configured hardware, the real
pdev id is not 0 in firmware, for example, its pdev id is 1 for 5G/6G
phy and 2 for 2G band phy. For HTT_H2T_MSG_TYPE_EXT_STATS_CFG message,
firmware parse the pdev_mask to its pdev id, ath11k set it to 0 for
single pdev, it is not correct, need set it with the real pdev id of
firmware.
Save the real pdev id report by firmware and set it correctly.
Below commands run success with this patch:
cat /sys/kernel/debug/ieee80211/phy0/ath11k/htt_stats
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wls1/stations/00\:03\:7f\:75\:59\:85/htt_peer_stats
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095700.8149-1-quic_wgong@quicinc.com
When connected to 6G mode AP, it does not have VHT/HT capabilities,
so the NSS is not set, then it is 1 by default.
This patch is to calculate the NSS with supported HE-MCS and NSS set
of HE capabilities.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01280-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095453.8030-1-quic_wgong@quicinc.com
With VT-d disabled on Intel platform, ath11k gets only one MSI
vector. In that case, ath11k does not free IRQ when doing suspend,
hence the kernel has to migrate it to CPU0 (if it was affine to
other CPUs) and allocates a new MSI vector. However, ath11k has
no chance to reconfig it to HW srngs during this phase, thus
ath11k fails to resume.
This issue can be fixed by setting IRQ affinity to CPU0 before
request_irq is called. With such affinity, migration will not
happen and thus the vector keeps unchanged during suspend/resume.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041732.5323-1-bqiang@codeaurora.org
Current code enables ASPM by default, it allows MHI to enter M2 state.
In case of one MSI vector, system hang is observed if ath11k does MHI
register reading in this state. The issue was reported on Dell XPS 13
9310 but is seen also on XPS 15 and XPS 17 laptops.
The workaround here is to prevent MHI from entering M2 state, this can
be done by disabling ASPM if only one MSI vector is used. When using 32
vectors ASPM is enabled as before.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041722.5271-1-bqiang@codeaurora.org
On some platforms it's not possible to allocate 32 MSI vectors for various
reasons, be it kernel configuration, VT-d disabled, buggy BIOS etc. So
ath11k was not able to use QCA6390 PCI devices on those platforms. Add
support for one MSI vector to solve that.
In case of one MSI vector, interrupt migration needs to be disabled. This
is because when interrupt migration happens, the msi_data may change.
However, msi_data is already programmed to rings during initial phase and
ath11k has no way to know that msi_data is changed during run time and
reprogram again.
In case of one MSI vector, MHI subsystem should not use IRQF_NO_SUSPEND
as QCA6390 doesn't set this flag too. Ath11k doesn't need to leave
IRQ enabled in suspend state.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041714.5219-1-bqiang@codeaurora.org
This change adds two flags to indicate whether IRQ handler for CE
and DP can be called. This is because in one MSI vector case,
interrupt is not disabled in hif_stop and hif_irq_disable. Otherwise,
MHI interrupt is disabled too.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041646.5060-1-bqiang@codeaurora.org
The reservation mode of interrupts in kernel assigns a dummy vector
when the interrupt is allocated and assigns a real vector when the
request_irq is called. The reservation mode helps to ease vector
pressure when devices with a large amount of queues/interrupts
are initialized, but only a minimal subset of those queues/interrupts
is actually used.
So on reservation mode, the msi_data may change after request_irq
is called, so ath11k reads msi_data again after request_irq is called,
and then the correct msi_data is programmed into QCA6390 hardware
components. Without this change, spurious interrupt occurs in case of
one MSI vector. When VT-d in BIOS is enabled and ath11k can get 32 MSI
vectors, ath11k always get the same msi_data before and after request_irq,
that's why this change is only required when one MSI vector is to be
supported.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041636.5008-1-bqiang@codeaurora.org
ath.git patches for v5.17. Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
The struct ath_hw member intr_txqs is never reset/assigned outside
of ath9k_hw_init_queues() and with the used bitwise-or in the interrupt
handling ar9002_hw_get_isr() accumulates all ever set interrupt flags.
Fix this by using a pure assign instead of bitwise-or for the
first line (note: intr_txqs is only evaluated in case ATH9K_INT_TX bit
is set).
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211116220720.30145-1-ps.report@gmx.net
Wakeup mhi is needed before pci_read/write only for QCA6390 and WCN6855. Since
wakeup & release mhi is enabled for all hardwares, below mhi assert is seen in
QCN9074 when doing 'rmmod ath11k_pci':
Kernel panic - not syncing: dev_wake != 0
CPU: 2 PID: 13535 Comm: procd Not tainted 4.4.60 #1
Hardware name: Generic DT based system
[<80316dac>] (unwind_backtrace) from [<80313700>] (show_stack+0x10/0x14)
[<80313700>] (show_stack) from [<805135dc>] (dump_stack+0x7c/0x9c)
[<805135dc>] (dump_stack) from [<8032136c>] (panic+0x84/0x1f8)
[<8032136c>] (panic) from [<80549b24>] (mhi_pm_disable_transition+0x3b8/0x5b8)
[<80549b24>] (mhi_pm_disable_transition) from [<80549ddc>] (mhi_power_down+0xb8/0x100)
[<80549ddc>] (mhi_power_down) from [<7f5242b0>] (ath11k_mhi_op_status_cb+0x284/0x3ac [ath11k_pci])
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[<7f5242b0>] (ath11k_mhi_op_status_cb [ath11k_pci]) from [<7f524878>] (ath11k_mhi_stop+0x10/0x20 [ath11k_pci])
[<7f524878>] (ath11k_mhi_stop [ath11k_pci]) from [<7f525b94>] (ath11k_pci_power_down+0x54/0x90 [ath11k_pci])
[<7f525b94>] (ath11k_pci_power_down [ath11k_pci]) from [<8056b2a8>] (pci_device_shutdown+0x30/0x44)
[<8056b2a8>] (pci_device_shutdown) from [<805cfa0c>] (device_shutdown+0x124/0x174)
[<805cfa0c>] (device_shutdown) from [<8033aaa4>] (kernel_restart+0xc/0x50)
[<8033aaa4>] (kernel_restart) from [<8033ada8>] (SyS_reboot+0x178/0x1ec)
[<8033ada8>] (SyS_reboot) from [<80301b80>] (ret_fast_syscall+0x0/0x34)
Hence, disable wakeup/release mhi using hw_param for other hardwares.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01060-QCAHKSWPL_SILICONZ-1
Fixes: a05bd85133 ("ath11k: read and write registers below unwindowed address")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com
The ath11k driver is caching the information about RSN/WPA IE in the
configured beacon template. The cached information is used during
associations to figure out whether 4-way PKT/2-way GTK peer flags need to
be set or not.
But the code never cleared the state when no such IE was found. This can
for example happen when moving from an WPA/RSN to an open setup. The
(seemingly connected) peer was then not able to communicate over the
link because the firmware assumed a different (encryption enabled) state
for the peer.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: 01e34233c6 ("ath11k: fix wmi peer flags in peer assoc command")
Cc: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-2-sven@narfation.org
DISABLE_KEY sets the key_len to 0, firmware will not delete the keys if
key_len is 0. Changing from security mode to open mode will cause mcast
to be still encrypted without vdev restart.
Set the proper key_len for DISABLE_KEY cmd to clear the keys in
firmware.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-1-sven@narfation.org
Whenever the MAC detects a color collision, or any of
its associated stations detects one, the firmware will
send out an event. Add the code to parse and handle
this event and pass the data up to mac80211.
The firmware does not provide an offload feature such
as the one used for CSA. The color change process is
hence triggered via the beacon offload tx completion
events sent out by firmware.
BSS color feature is enabled depending on service flag
advertised by firmware, based on which color change
functionality is invoked.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00680-QCAHKSWPL_SILICONZ-1
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635178254-17732-1-git-send-email-quic_ramess@quicinc.com
Currently ath11k only support string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for ahb bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCIe bus chip in
board-2.bin. For WCN6855, it is not enough to distinguish all different
chips.
This is to add a new string type which include bus, chip id, board id,
vendor, device, subsystem-vendor and subsystem-device for WCN6855.
ath11k will first load board-2.bin and search in it for the board data
with the above parameters, if matched one board data, then download it
to firmware, if not matched any one, then ath11k will download the file
board.bin to firmware.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111065340.20187-1-quic_wgong@quicinc.com
Currently many functions do not follow this guidance when
qmi_send_request() fails, therefore add missing
qmi_txn_cancel() in the qmi_send_request() error path.
Also remove initialization on 'struct qmi_txn'
since qmi_tx_init() performs all necessary initialization.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635857558-21733-1-git-send-email-akolli@codeaurora.org
