The PLL_LOCKDET_RATE_1 was being programmed with a hardcoded value
directly, but the same value was also being specified in the
dsi_pll_regs struct pll_lockdet_rate variable: let's use it!
Based on 362cadf34b ("drm/msm/dsi_pll_10nm: Fix variable usage for
pll_lockdet_rate")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The number of fractional registers bits is known and already set in
the frac_bits variable of the dsi_pll_config struct here in 7nm:
remove the TODO by simply using that variable. This is a copy of
196145eb1a ("drm/msm/dsi_pll_10nm: Solve TODO for multiplier frac_bits
assignment").
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix setting min/max DSI PLL rate for the V4.1 7nm DSI PLL (used on
sm8250). Current code checks for pll->type before it is set (as it is
set in the msm_dsi_pll_init() after calling device-specific functions.
Cc: Jonathan Marek <jonathan@marek.ca>
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The PLL_LOCKDET_RATE_1 was being programmed with a hardcoded value
directly, but the same value was also being specified in the
dsi_pll_regs struct pll_lockdet_rate variable: let's use it!
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The number of fractional registers bits is known and already set in
the frac_bits variable of the dsi_pll_config struct here in 10nm:
remove the TODO by simply using that variable.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In function dsi_pll_calc_dec_frac we are calculating the decimal
div start parameter by dividing the decimal multiple by the
fractional multiplier: the remainder of that operation is stored
to then get programmed to the fractional divider registers of
the PLL.
It's useless to call div_u64_rem to get the remainder and *then*
call div_u64 to get the division result, as the first is already
giving that result: let's fix it by just caring about the result
of div_u64_rem.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The previous registers were *almost* correct, but instead of
PHYs, they were pointing at DSI PLLs, resulting in the PHY id
autodetection failing miserably.
Fixes: dcefc117cc ("drm/msm/dsi: Add support for msm8x94")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The only usage of dsi_host_ops is to assign its address to the ops field
in the mipi_dsi_host struct, which is a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reading VCO rate for this PLL can cause boot stalls, if it is not
enabled. Guard clk_hw_get_rate with a call to
dsi_pll_28nm_clk_is_enabled().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Implement phy_disable() callback to disable DSI PHY lanes and blocks
when phy is not used.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: ff73ff1940 ("drm/msm/dsi: Populate the 10nm PHY funcs")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Implement phy_disable() callback to disable DSI PHY lanes and blocks
when phy is not used.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Rob Clark <robdclark@chromium.org>
PHY disable/enable resets PLL registers to default values. Thus in
addition to restoring several registers we also need to restore VCO rate
settings.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: c6659785df ("drm/msm/dsi/pll: call vco set rate explicitly")
Signed-off-by: Rob Clark <robdclark@chromium.org>
PHY disable/enable resets PLL registers to default values. Thus in
addition to restoring several registers we also need to restore VCO rate
settings.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Rob Clark <robdclark@chromium.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, also create a label to put clkname.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
* DSI support for sm8150/sm8250
* Support for per-process GPU pagetables (finally!) for a6xx.
There are still some iommu/arm-smmu changes required to
enable, without which it will fallback to the current single
pgtable state. The first part (ie. what doesn't depend on
drm side patches) is queued up for v5.10[1].
* DisplayPort support. Userspace DP compliance tool support
is already merged in IGT[2]
* The usual assortment of smaller fixes/cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvqjuzH=Po_9EzzFsp2Xq3tqJUTKfsA2g09XY7_+6Ypfw@mail.gmail.com
This adds support for the 7nm ("V4") DSI PHY/PLL for sm8150 and sm8250.
Implementation is based on 10nm driver, but updated based on the downstream
7nm driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>
This allows DSI driver to work with sm8150 and sm8250. The sdm845 config
is re-used as the config is the same.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Backmerging drm-next into drm-misc-next for nouveau and panel updates.
Resolves a conflict between ttm and nouveau, where struct ttm_mem_res got
renamed to struct ttm_resource.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
These SoCs make use of the 14nm phy, but at different
addresses than other 14nm units.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
On SDM845 and SC7180 DSI needs to express a performance state
requirement on a power domain depending on the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
dev_pm_opp_set_rate() is designed to be equivalent to clk_set_rate()
for devices without an OPP table, hence the change works fine
on devices/platforms which only need to set a clock rate.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
"The PM core always increments the runtime usage counter
before calling the ->suspend() callback and decrements it
after calling the ->resume() callback"
DPU and DSI are managed as runtime devices. When
suspend is triggered, PM core adds a refcount on all the
devices and calls device suspend, since usage count is
already incremented, runtime suspend was not getting called
and it kept the clocks on which resulted in target not
entering into XO shutdown.
Add changes to force suspend on runtime devices during pm sleep.
Changes in v1:
- Remove unnecessary checks in the function
_dpu_kms_disable_dpu (Rob Clark).
Changes in v2:
- Avoid using suspend_late to reset the usagecount
as suspend_late might not be called during suspend
call failures (Doug).
Changes in v3:
- Use force suspend instead of managing device usage_count
via runtime put and get API's to trigger callbacks (Doug).
Changes in v4:
- Check the return values of pm_runtime_force_suspend and
pm_runtime_force_resume API's and pass appropriately (Doug).
Changes in v5:
- With v4 patch, test cycle has uncovered issues in device resume.
On bubs: cmd tx failures were seen as SW is sending panel off
commands when the dsi resources are turned off.
Upon suspend, DRM driver will issue a NULL composition to the
dpu, followed by turning off all the HW blocks.
v5 changes will serialize the NULL commit and resource unwinding
by handling them under PM prepare and PM complete phases there by
ensuring that clks are on when panel off commands are being
processed.
Changes in v6:
- Use drm_mode_config_helper_suspend/resume() instead of legacy API
drm_atomic_helper_suspend/resume() (Doug).
Trigger runtime callbacks from the suspend/resume call to turn
off the resources.
Changes in v7:
- Add "__maybe_unused" to the functions to avoid compilation
failures. Cleanup unnecessary configs (Doug).
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
For a given byte clock, if VCO recalc value is exactly same as
vco set rate value, vco_set_rate does not get called assuming
VCO is already set to required value. But Due to GDSC toggle,
VCO values are erased in the HW. To make sure VCO is programmed
correctly, we forcefully call set_rate from vco_prepare.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Save pll state before dsi host is powered off. Without this change
some register values gets resetted.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
