The DSI host might be left in some state by the bootloader. If this
state generates an IRQ, it might hang the system by holding the
interrupt line before the driver sets up the DSI host to the known
state.
Move the request_irq into msm_dsi_host_init and pass IRQF_NO_AUTOEN to
it. Call enable/disable_irq after msm_dsi_host_power_on/_off()
functions, so that we can be sure that the interrupt is delivered when
the host is in the known state.
It is not possible to defer the interrupt enablement to a later point,
because drm_panel_prepare might need to communicate with the panel over
the DSI link and that requires working interrupt.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211002010830.647416-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
'of_find_device_by_node()' takes a reference that must be released when
not needed anymore.
This is expected to be done in 'dsi_destroy()'.
However, there are 2 issues in 'dsi_get_phy()'.
First, if 'of_find_device_by_node()' succeeds but 'platform_get_drvdata()'
returns NULL, 'msm_dsi->phy_dev' will still be NULL, and the reference
won't be released in 'dsi_destroy()'.
Secondly, as 'of_find_device_by_node()' already takes a reference, there is
no need for an additional 'get_device()'.
Move the assignment to 'msm_dsi->phy_dev' a few lines above and remove the
unneeded 'get_device()' to solve both issues.
Fixes: ec31abf668 ("drm/msm/dsi: Separate PHY to another platform device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/f15bc57648a00e7c99f943903468a04639d50596.1628241097.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Rob Clark <robdclark@chromium.org>
During board bringups its useful to have a DSI test pattern
generator to isolate a DPU vs a DSI issue and focus on the relevant
hardware block.
To facilitate this, add an API which triggers the DSI controller
test pattern. The expected output is a rectangular checkered pattern.
This has been validated on a single DSI video mode panel by calling it
right after drm_panel_enable() which is also the ideal location to use
this as the DSI host and the panel have been initialized by then.
Further validation on dual DSI and command mode panel is pending.
If there are any fix ups needed for those, it shall be applied on top
of this change.
Changes in v2:
- generate the new dsi.xml.h and update the bitfield names
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/1626922232-29105-2-git-send-email-abhinavk@codeaurora.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Based on mesa commit daa2ccff7a0201941db3901780d179e2634057d5
Small bit of .c churn in the phy code to adapt to split up of phy
related registers.
Signed-off-by: Rob Clark <robdclark@chromium.org>
clang is a little overzealous with warning about a constant conversion
in an untaken branch of a ternary expression:
drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c:975:48: error: implicit conversion from 'unsigned long long' to 'unsigned long' changes value from 5000000000 to 705032704 [-Werror,-Wconstant-conversion]
.max_pll_rate = (5000000000ULL < ULONG_MAX) ? 5000000000UL : ULONG_MAX,
^~~~~~~~~~~~
Rewrite this to use a preprocessor conditional instead to avoid the
warning.
Fixes: 076437c9e3 ("drm/msm/dsi: move min/max PLL rate to phy config")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210514213032.575161-1-arnd@kernel.org
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix following warnings generated when either DP or DSI support is
disabled:
drivers/gpu/drm/msm/disp/msm_disp_snapshot_util.c:141:3: error: implicit declaration of function 'msm_dp_snapshot'; did you mean 'msm_dsi_snapshot'? [-Werror=implicit-function-declaration]
drivers/gpu/drm/msm/msm_kms.h:127:26: warning: 'struct msm_disp_state' declared inside parameter list will not be visible outside of this definition or declaration
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c:867:21: error: initialization of 'void (*)(struct msm_disp_state *, struct msm_kms *)' from incompatible pointer type 'void (*)(struct msm_disp_state *, struct msm_kms *)' [-Werror=incompatible-pointer-types]
drivers/gpu/drm/msm/dsi/dsi.h:94:30: warning: 'struct msm_disp_state' declared inside parameter list will not be visible outside of this definition or declaration
Reported-by: kernel test robot <lkp@intel.com>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Fixes: 1c3b7ac1a71d ("drm/msm: pass dump state as a function argument")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210527220330.3364716-1-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the msm_disp_snapshot module which adds supports to dump dpu
registers and capture the drm atomic state which can be used in
case of error conditions.
changes in v5:
- start storing disp_state in msm_kms instead of dpu_kms
- get rid of MSM_DISP_SNAPSHOT_IN_* enum by simplifying the functions
- move snprintf inside the snapshot core by using varargs
- get rid of some stale code comments
- allow snapshot module for non-DPU targets
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1618606645-19695-3-git-send-email-abhinavk@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
A problem was reported on CoachZ devices where the display wouldn't come
up, or it would be distorted. It turns out that the PLL code here wasn't
getting called once dsi_pll_10nm_vco_recalc_rate() started returning the
same exact frequency, down to the Hz, that the bootloader was setting
instead of 0 when the clk was registered with the clk framework.
After commit 001d8dc338 ("drm/msm/dsi: remove temp data from global
pll structure") we use a hardcoded value for the parent clk frequency,
i.e. VCO_REF_CLK_RATE, and we also hardcode the value for FRAC_BITS,
instead of getting it from the config structure. This combination of
changes to the recalc function allows us to properly calculate the
frequency of the PLL regardless of whether or not the PLL has been
clk_prepare()d or clk_set_rate()d. That's a good improvement.
Unfortunately, this means that now we won't call down into the PLL clk
driver when we call clk_set_rate() because the frequency calculated in
the framework matches the frequency that is set in hardware. If the rate
is the same as what we want it should be OK to not call the set_rate PLL
op. The real problem is that the prepare op in this driver uses a
private struct member to stash away the vco frequency so that it can
call the set_rate op directly during prepare. Once the set_rate op is
never called because recalc_rate told us the rate is the same, we don't
set this private struct member before the prepare op runs, so we try to
call the set_rate function directly with a frequency of 0. This
effectively kills the PLL and configures it for a rate that won't work.
Calling set_rate from prepare is really quite bad and will confuse any
downstream clks about what the rate actually is of their parent. Fixing
that will be a rather large change though so we leave that to later.
For now, let's stash away the rate we calculate during recalc so that
the prepare op knows what frequency to set, instead of 0. This way
things keep working and the display can enable the PLL properly. In the
future, we should remove that code from the prepare op so that it
doesn't even try to call the set rate function.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Fixes: 001d8dc338 ("drm/msm/dsi: remove temp data from global pll structure")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210608195519.125561-1-swboyd@chromium.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
