[why]
According to DP specs, in EQ DONE phase of link training, we
should lower lane count when at least one CR DONE bit is set to 1, while
lower link rate when all CR DONE bits are 0s. However in our code, we will
treat both cases as latter. This is not exactly correct based on the specs
expectation.
[how]
Check lane0 CR DONE bit when it is still set but CR DONE fails,
we treat it as a partial CR DONE failure in EQ DONE phase, we
will follow the same fallback flow as when ED DONE fails in EQ
DONE phase.
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
To reduce stack usage, move some variables into heap in the DML function
dml32_ModeSupportAndSystemConfigurationFull()
Fixes: dda4fb85e4 ("drm/amd/display: DML changes for DCN32/321")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a theoretical problem in prior patches for reducing the stack
size of *update_bw_bounding_box() functions.
By modifying the soc.clock_limits[n] struct directly, this can cause
unintended behavior as the for loop attempts to swap rows in
clock_limits[n]. A temporary struct is still required to make sure we
stay functinoally equivalent.
[How]
Add a temporary clock_limits table to the SOC struct, and use it when
swapping rows.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Getting below errors:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn32/display_mode_vba_32.c:1414:5: error: implicit conversion from enumeration type 'enum scan_direction_class' to different enumeration type 'enum dm_rotation_angle' [-Werror,-Wenum-conversion]
mode_lib->vba.SourceScan[k],
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn32/display_mode_vba_32.c:1744:22: error: implicit conversion from enumeration type 'enum scan_direction_class' to different enumeration type 'enum dm_rotation_angle' [-Werror,-Wenum-conversion]
&& (!(!IsVertical(mode_lib->vba.SourceScan[k])) || mode_lib->vba.DCCEnable[k] == true)) {
~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~
2 errors generated.
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn32/display_mode_vba_util_32.c:5484:18: error: implicit conversion from enumeration type 'RequestType' to different enumeration type 'enum RequestType' [-Werror,-Wenum-conversion]
RequestLuma = REQ_256Bytes;
~ ^~~~~~~~~~~~
18 errors of similar kind
[How]
1. Add typecast at relevant places
2. Move the enum RequestType definition ahead of declarations
Signed-off-by: Chandan Vurdigere Nataraj <chandan.vurdigerenataraj@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GCC throw warnings for the function dcn21_update_bw_bounding_box and
dcn316_update_bw_bounding_box due to its frame size that looks like
this:
error: the frame size of 1936 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
For fixing this issue I dropped an intermadiate variable.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GCC throw warnings for the function dcn31_update_bw_bounding_box and
dcn316_update_bw_bounding_box due to its frame size that looks like
this:
error: the frame size of 1936 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
For fixing this issue I dropped an intermadiate variable.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GCC throw warnings for the function dcn20_update_bounding_box due to its
frame size that looks like this:
error: the frame size of 1936 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
This commit fixes this issue by eliminating an intermediary variable
that creates a large array.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In cases where there are multiple eDP instances, DMUB needs to know
which instance the command is for. Today, the field for specifying the
panel_inst exists in both dmub_cmd_update_dirty_rect_data and
dmub_cmd_update_cursor_info_data.
For cursor updates, we already specify the panel_inst, but that's not
the case for dirty_rect updates. Today, a value of '0' is used (due
to initial memsetting of the cmd struct to 0)
[how]
In dc_dmub_update_dirty_rect(), Call dc_get_edp_link_panel_inst() to get
the panel_inst, and fill it in the DMUB cmd struct.
v2: Update commit message for clarity.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR-SU Rate Control - or PSR-SU-RC - enables PSR-SU panels to work with
variable refresh rate to allow for more power savings. Lowering the
refresh rate can increase PSR residency by expanding the eDP main link
shut down duration. It can also lower panel power consumption.
There is a complication with PSR, since the eDP main link can be shut
down. Therefore, the timing controller (TCON) on the eDP sink nees to be
able to scan out its remote buffer independent of the main link. To
allow the eDP source to specify the sink's refresh rate while the link
is off, vendor-specific DPCD registers are used. This allows the eDP
source to then "Rate Control" the panel during PSR active.
[How]
Add DC support to communicate with PSR-SU-RC supported eDP sinks. The
sink will need to know the desired VTotal during PSR active.
This change only adds support to DC, support in amdgpu_dm is still
pending to enable this fully.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following:
- DPP DTO fix
- Transient encoder fix
- Restrict the reading of LTTPR capabilities in LTTPR mode
- Increase maximum stages for BB
- Distinguish HDMI DTO from DP DTO
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For Pixel Rate control, when on HDMI, HDMI DTO
should be selected instead of DP DTO.
[How]
Add HDMI member to dtbclk_dto_params, so it can be used tell apart HDMI
and DP DTO in the future.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some scenarios it is possible for the encoder assignment module to be
set to "transient" mode even though there are no new encoder
assignments.
This can lead to incorrect results when querying encoder assignment,
which in turn can cause incorrect displays to be manipulated.
[How]
Only allow encoder assignment to be in transient mode of operation when
there are valid new encoder assignments.
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching from 1 pipe to 4to1 mpc combine,
DppDtoClk aren't enabled for the disabled pipes
pior to programming the pipes. Upon optimizing
bandwidth, DppDto are enabled causing intermittent
underflow.
[How]
Update dppclk dto whenever pipe are flagged to
enable.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following:
- Optimized blank calculations
- More robust DP MST hotplug support
- eDP bug fix relating to ODM
- Revert a patch that caused a regression with DP
- min comp buffer size fix
- Make DP easier to debug
- Calculate the maximum OLED brightness correctly
- 3 plane MPO.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
1. When HPD deassertion is pulled in the middle of
enabe stream link training, we will abort current training
and turn off PHY. This causes current link settings
to be zeroed this causes later stream enablement
sequence to fail as we prefer to carry on enablement
process despite of link training failure for SST.
2. When HPD is toggled after detection before before
the enable stream sequence as a result. There could be
a race condition where we could end up enable stream based
on the previous link even though the link is updated
after the HPD toggle. This causes an issue where our link
bandwidth is no longer enough to accommodate the timing
therefore causes us to oversubscribe MST payload time
slots. As discussed we decided to add basic sanity check
to make sure that our code can handle the oversubscription
failure silently without system hang.
[how]
1. Keep PHY powered on when HPD is deasserted during
enable stream and wait for the detection sequence to power
it off later.
2. Do not allocate payload if the required timeslot for
current timing is greater than 64 timeslots.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In 3-way mpo pipes, there is a case that we
overbook the CRB buffer size. At rare instances,
overbooking the crb will cause underflow. This only
happens when det_size changes dynamically
based on pipe_cnt.
[How]
Set min compbuff size to 1 segment when preparing BW.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For panels with pixel clock > 1200MHz that require ODM
in pre-OS, when driver is disabled in OS, odm is enabled.
Upon driver enablement, corruption is seen if
odm was originally enabled. DP_PIXEL_COMBINE and
pixelclk must be programmed prior to programming the
optc-odm registers. However, eDP displays aren't blanked
prior to initializing odm in this case.
[How]
Upon driver enablement, check whether odm is enabled,
if so, blank eDP prior to programming optc-odm
registers.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
LTTPR capable devices on the DisplayPort path may assume that
extended LTTPR AUX timeouts will be used after LTTPR capabilities
are read.
When DPTX operates in non-LTTPR mode, AUX timeouts are not
extended and this can result in AUX transactions timing out.
[How]
Use shared helper function to determine LTTPR mode and do not
read LTTPR capabilities in non-LTTPR mode.
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The existing calculations in DCN3.1 were placeholder and need to be
replaced with HW team approved calculations.
[How]
The new calculations add new parameters to the bounding box and pipe
params - VblankNom and the bounding box default.
The placeholder calculations are dropped from DCN3.1 in the meantime
while we work out hardware approved replacements.
Also fix a bug where we wipe out other register contents with a REG_SET
instead of a REG_UPDATE for the register we were programming the
min_dst_y_next_start_optimized.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To involve the cursor position into dirty rectangle calculation.
[how]
- separate plane and cursor update by different DMUB command
- send the cursor information while cursor updating, when updating
cursor position/attribute, store cursor pos/attr to hubp, and
notify dmub FW to exit psr before program cursor registers
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some specific TCON chip has HW limitation to support PSRSU+DSC.
[how]
Force ffu mode when DSC enabled if we detect it is the specific
model from sink OUI DPCD. And disable ABM update for this case.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Feature requires synchronization of dig, pipe, and cursor locking
between driver and DMUB fw for PSR-SU
[how]
return True if PSR-SU in the checker should_use_dmub_lock()
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
While support ALPM, do ALPM state transition while PSR entry/exit.
ALPM is needed for PSR-SU feature, and since the function is ready,
we'd enable it by default.
- Add psr level definition to enable/disable ALPM and set ALPM
powerdone mode.
- Enable ALPM by default
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When DC driver send PSR exit dmub command to DMUB FW, it might not
wait until PSR exit. Then it may hit the following deadlock situation.
1. DC driver send HW LOCK command to DMUB FW due to frame update
2. DMUB FW Set the HW lock
3. DMUB execute PSR exit sequence and stuck at polling DPG Pending
register due to the HW Lock is set
4. DC driver ask DMUB FW to unlock HW lock, but DMUB FW is polling
DPG pending register
[how]
The reason why DC driver doesn't wait until PSR exit is because some of
the PSR state machine state is not update the dc driver. So when DC
driver read back the PSR state, it take the state for PSR inactive.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current PSR SU programming margin is fixed base on FHD 60HZ
panel. If the resolution and refresh rate become higher, the time
of current margin might not cover the programming SU time.
[how]
Notice that the programming SU time is the same among different
panels.
Instead of fixing the margin with target line number, change the
margin unit to micro second which indicate the time needed for
programming SU. Then FW set the margin line number base on the
line time and margin time.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The Y-granularity panel parameter indicate the grid
pattern granularity in the Y direction for PSRSU.
[How]
Send the Y-granularity data by PSR_COPY_SETTINGS dmub command.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Based on PSRSU specification, every selective update frame need to use
two SDP to indicate the frame active range. So we occupy another GSP1
for PSRSU execution.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In PSR-SU design, the DMUB FW handles the combination of multiple
dirty rectangles.
[how]
- create DC dmub update dirty rectangle helper which sends the
dirty rectangles per pipe from DC to DMUB, and DMUB FW will
handle to combine the dirty RECTs
- call the helper from DC commit plane update function.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Protect remove_hpo_dp_link_enc_from_ctx() and release_hpo_dp_link_enc()
with CONFIG_DRM_AMD_DC_DCN as the functions are only called from code
that is protected by CONFIG_DRM_AMD_DC_DCN. Fixes build fail with
-Werror=unused-function.
Fixes: 9b0e0d433f74 ("drm/amd/display: Add dependant changes for DCN32/321")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Revised validation logic when marking for seamless boot. Init resources
accordingly when Pre-OS has ODM enabled. Reset ODM when transitioning
Pre-OS odm to Post-OS non-odm to avoid corruption. Apply logic to set
odm accordingly upon commit.
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Implements DTB ref clock switching with reg key default to OFF.
Refactors dccg DTBCLK logic to not store redundant state information
dccg. Also removes duplicated functions that should be inherited from
other dcn versions.
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update base.dprefclk_khz to match result from dcn32_dump_clk_registers()
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit cleans up code that uses old variables and adds some SMU
interfaces for future flexibility.
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously we used to send FCLK P-state enable messages upon each call
to update_clocks based on dml output. This resulted in increased message
transactions between DC and PMFW.
[How]
Update the code to check safe_to_lower status and send the message based
on dml input only on boot. This reduces message transactions. Also
remove other unwanted code based on current code status.
Signed-off-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
