[why]
DP2.0 defines DP2.0 RX capability using bit maps. This means there is
a corner case the DP2.0 RX can declare UHBR20 capability but not UHBR13.5 support.
In this case we should skip UHBR13.5 selection and continue to our next option
in decide liink settings.
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is nice to have link training and link loss status logging in
our trace, and this patch add the all necessary accessors in dc
side.
[How]
1. Define dp_trace struct and create new file link_dp_trace.c and
link_dp_trace.h;
2. Add dp link training status update in dc_link_dp.c;
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a sequence in which aux arbitration
doesn't work correctly. Driver is left with
aux access after it times out waiting for access.
In future dmub fw is never granted aux access
and is stuck in a while loop.
[How]
Cancel aux request from driver after timing out.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?] When adding/removng a plane to some configurations,
unsupported pipe programming can occur when moving to a new plane.
[HOW?]
Add a safe transistion state before programming new configuration.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: 3.2.175
This version brings along following fixes:
- Remove invalid RDPCS Programming in DAL
- Make functional resource functions non-static
- Reset VIC if HDMI_VIC is present
- Add frame alternate 3D & restrict HW packed on dongles
- Reg to turn on/off PSR Power seq in FSM
- Modify plane removal sequence to avoid hangs
- Pass HostVM enable flag into DCN3.1 DML
- DC Validation failures
- Program OPP before ODM
- Refactor fixed VS w/a for PHY tests
- Pass deep sleep disabled allow info to dmub fw
- Refine the EDID override
- [FW Promotion] Release 0.0.106.0
- Add verify_link_cap back for hdmi
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We already get the SBIOS EDID via ACPI on KMD,
but after that, we just use the monitor EDID to set it HDR caps
[How]
Make the SBIOS EDID override to read_edid()
That can change the read EDID caps from the right EDID
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: jinzh <jinzh@github.amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Calculations differ with HostVM enabled/disabled, causing underflow in
configs with high refresh displays + scaling due to lower available BW
[HOW]
Check riommu_active in order to pass correct HostVM enablement to DML
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Some projectors support frame alternate 3D modes at 120Hz, but DAL3 does
not create timings. Most active DP to HDMI dongles do not translate
infoframes properly to use HW packing stereo mode.
[HOW?]
Create frame alternate 3D timings for displays that support it. Disable HW
packing 3D mode on DP active dongles.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Silence [-Wmissing-prototypes] sparse warnings from the display folder
such as:
../drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn315/dcn315_smu.c:126:5: warning: no previous prototype for ‘dcn315_smu_send_msg_with_param’ [-Wmissing-prototypes]
126 | int dcn315_smu_send_msg_with_param(
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
v2: drop unused function dcn315_smu_set_voltage_via_phyclk() to avoid
adding a warning (Alex)
Cc: Qingqing Zhuo (Lillian) <qingqing.zhuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Silence the following sparse warnings:
../drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:865:16:
sparse: warning: Using plain integer as NULL pointer
../drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:1588:84:
sparse: warning: Using plain integer as NULL pointer
../drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:2725:84:
sparse: warning: Using plain integer as NULL pointer
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1919:16:
sparse: warning: Using plain integer as NULL pointer
v2: drop removal of default case to avoid adding warnings (Alex)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Part of the documentation of the 'dc_process_dmub_aux_transfer_async'
function was misplaced, being put together with the
‘dc_enable_dmub_notifications’ documentation. This caused the following
warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:3757: warning:
expecting prototype for dc_process_dmub_aux_transfer_async(). Prototype
was for dc_enable_dmub_notifications() instead
This commit fixes the warning by placing the function documentations in
their right place.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During DC init, we read power management tables from PMFW. This info is
exchanged in the form of a binary blob inside gpu memory. In order to
parse the binary blob, the correct struct needs to be used.
[How]
Fix dcn316's definition of the DfPstateTable_t struct to align with PMFW
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DML validation fails when we connect two or
more displays with HDR. Need to increase
DRAM BW to make the validation passing.
Following the value from DCN31.
[how]
Change the max DRAM BW DML field to 60%.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Detbuffer size is dynamically set for dcn31x. At certain moment,
compbuf+(def size * num pipes) > config return buffer size causing
flickering. This is easily reproducible when MPO is
enabled with two displays.
[How]
At prepare BW, use the min comp buffer size. When it is to
optimize BW, set compbuf size back to maximum possible size.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Duncan Ma <duncanma@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Due to how pmfw fills out the table when dcfclk states are disabled,
using dcfclk based clk table would cause a no read situation.
Revert the change to prevent underflow until a better solution is coded.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- add debug option to bypass ssinfo from bios.
- Refactor fixed VS logic for non-transparent mode
- add cable ID support for usb c connector
- clear remote dc_sink when stop mst
- Ignore Transitional Invalid Link Rate Error Message
- Fix wrong resolution with DP/VGA adapter
- Refactor PSR DPCD caps detection
- Set compbuf size to min at prep prevent overbook crb
- lock/un-lock cursor if odm pipe split used
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All fixed VS/PE link training sequence should be refactored
into a separate function outside of the standard link training
sequence. This includes the sequence for non-transparent
mode.
[How]
Isolate link training sequence for fixed VS/PE non-transparent
mode into a separate function.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When hotplug or unplug happens, each stream disabled one by one, and then
enable any alived streams. Link phy and payload table is cleared when 1st
stream is disabled. That causes the error message pops up when disable 2nd
stream. There is no active stream after link_rate is cleared.
After all streams are disabled, link will be trained again and link rate is
assigned to any alived streams.
Therefore there is no harm for the error message that represents invalid
link rate value in the atomic reset transitional time period.
[How]
Downgrade the log level from ERROR to DEBUG.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hotplugging the VGA side of some DP/VGA adapters caused the display to
light up with the wrong (non-native) resolution.
This is caused by the adapter misbehaving by reporting the wrong number
of downstream ports when the VGA side is unplugged (reports 1 instead of
0), but only if the SINK_COUNT DPCD register is read more than once.
[How]
To work around the adapter behavior, remove the sink if link is
detected, but EDID cannot be read.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Ilya <Ilya.Bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Detbuffer size is dynamically set for dcn31x. At certain moment,
compbuf+(def size * num pipes) > config return buffer size causing
flickering. This is easily reproducible when MPO is
enabled with two displays.
[How]
At prepare BW, use the min comp buffer size. When it is to
optimize BW, set compbuf size back to maximum possible size.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Duncan Ma <duncanma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When system resume from sleep, the cursor lock will be reset
to default(lock status). And the cursor programming sequence
doesn't consider about odm pipe split cause cursor can't be
enabled.
[How]
If odm pipe split has been used, lock/un-lock on each pipes.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Turn previously global functions into static functions to avoid
-Wmissing-prototype warnings, such as:
drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn30/irq_service_dcn30.c:50:20:
warning: no previous prototype for function 'to_dal_irq_source_dcn30'
[-Wmissing-prototypes]
enum dc_irq_source to_dal_irq_source_dcn30(
^
drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn30/irq_service_dcn30.c:50:1:
note: declare 'static' if the function is not intended to be used outside
of this translation unit
enum dc_irq_source to_dal_irq_source_dcn30(
^
static
1 warning generated.
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:488:6:
warning: no previous prototype for function
'dcn316_clk_mgr_helper_populate_bw_params' [-Wmissing-prototypes]
void dcn316_clk_mgr_helper_populate_bw_params(
^
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:488:1:
note: declare 'static' if the function is not intended to be used outside
of this translation unit
void dcn316_clk_mgr_helper_populate_bw_params(
^
static
1 warning generated.
v2: drop is_timing_changed hunk (Alex)
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Include the header with the prototype to silence the following clang
warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn201/dcn201_init.c:127:6:
warning: no previous prototype for function 'dcn201_hw_sequencer_construct'
[-Wmissing-prototypes]
void dcn201_hw_sequencer_construct(struct dc *dc)
^
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the variable clamshell_closed from the function
dcn10_align_pixel_clocks.
This was pointed by clang with the following warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2063:7:
warning: variable 'clamshell_closed' set but not used
[-Wunused-but-set-variable]
bool clamshell_closed = false;
^
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the unused struct irq_source_info_funcs
dmub_outbox_irq_info_funcs from the file, which was declared but never
hooked up.
This was pointed by clang with the following warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn201/irq_service_dcn201.c:141:43:
warning: unused variable 'dmub_outbox_irq_info_funcs'
[-Wunused-const-variable]
static const struct irq_source_info_funcs dmub_outbox_irq_info_funcs = {
^
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove dcn316_smu_set_voltage_via_phyclk function, which is not used in the
codebase.
This was pointed by clang with the following warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_smu.c:171:5:
warning: no previous prototype for function
'dcn316_smu_set_voltage_via_phyclk' [-Wmissing-prototypes]
int dcn316_smu_set_voltage_via_phyclk(struct clk_mgr_internal *clk_mgr, int
requested_phyclk_khz)
^
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
