PolarFire SoC does not have the same l2 cache controller as the fu540,
featuring an extra interrupt. Appease the devicetree checker overlords
by adding a PolarFire SoC specific compatible to fix the below sort of
warnings:
mpfs-polarberry.dtb: cache-controller@2010000: interrupts: [[1], [3], [4], [2]] is too long
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Fixes: 34fc9cc3ae ("riscv: dts: microchip: correct L2 cache interrupts")
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Recent versions of dt-schema warn about a previously undetected
undocumented property:
arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dtb: mmc@20008000: Unevaluated properties are not allowed ('card-detect-delay' was unexpected)
From schema: Documentation/devicetree/bindings/mmc/cdns,sdhci.yaml
There are no GPIOs connected to MSSIO6B4 pin K3 so adding the common
cd-debounce-delay-ms property makes no sense. The Cadence IP has a
register that sets the card detect delay as "DP * tclk". On MPFS, this
clock frequency is not configurable (it must be 200 MHz) & the FPGA
comes out of reset with this register already set.
Fixes: bc47b2217f ("riscv: dts: microchip: add the sundance polarberry")
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Recent versions of dt-schema warn about a previously undetected
undocument property on the icicle & polarberry devicetrees:
arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dtb: ethernet@20112000: ethernet-phy@8: Unevaluated properties are not allowed ('ti,fifo-depth' was unexpected)
From schema: Documentation/devicetree/bindings/net/cdns,macb.yaml
I know what you're thinking, the binding doesn't look to be the problem
and I agree. I am not sure why a TI vendor property was ever actually
added since it has no meaning... just get rid of it.
Fixes: bc47b2217f ("riscv: dts: microchip: add the sundance polarberry")
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Recent versions of dt-schema complain about the PCIe controller's child
node name:
arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dtb: pcie@2000000000: Unevaluated properties are not allowed ('clock-names', 'clocks', 'legacy-interrupt-controller', 'microchip,axi-m-atr0' were unexpected)
From schema: Documentation/devicetree/bindings/pci/microchip,pcie-host.yaml
Make the dts match the correct property name in the dts.
Fixes: 528a5b1f25 ("riscv: dts: microchip: add new peripherals to icicle kit device tree")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The "PolarFire SoC MSS Technical Reference Manual" documents the
following PLIC interrupts:
1 - L2 Cache Controller Signals when a metadata correction event occurs
2 - L2 Cache Controller Signals when an uncorrectable metadata event occurs
3 - L2 Cache Controller Signals when a data correction event occurs
4 - L2 Cache Controller Signals when an uncorrectable data event occurs
This differs from the SiFive FU540 which only has three L2 cache related
interrupts.
The sequence in the device tree is defined by an enum:
enum {
DIR_CORR = 0,
DATA_CORR,
DATA_UNCORR,
DIR_UNCORR,
};
So the correct sequence of the L2 cache interrupts is
interrupts = <1>, <3>, <4>, <2>;
[Conor]
This manifests as an unusable system if the l2-cache driver is enabled,
as the wrong interrupt gets cleared & the handler prints errors to the
console ad infinitum.
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
CC: stable@vger.kernel.org # 5.15: e35b07a7df: riscv: dts: microchip: mpfs: Group tuples in interrupt properties
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Pull RISC-V updates from Palmer Dabbelt:
- Enabling the FPU is now a static_key
- Improvements to the Svpbmt support
- CPU topology bindings for a handful of systems
- Support for systems with 64-bit hart IDs
- Many settings have been enabled in the defconfig, including both
support for the StarFive systems and many of the Docker requirements
There are also a handful of cleanups and improvements, as usual.
* tag 'riscv-for-linus-5.20-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (28 commits)
riscv: enable Docker requirements in defconfig
riscv: convert the t-head pbmt errata to use the __nops macro
riscv: introduce nops and __nops macros for NOP sequences
RISC-V: Add fast call path of crash_kexec()
riscv: mmap with PROT_WRITE but no PROT_READ is invalid
riscv/efi_stub: Add 64bit boot-hartid support on RV64
riscv: cpu: Add 64bit hartid support on RV64
riscv: smp: Add 64bit hartid support on RV64
riscv: spinwait: Fix hartid variable type
riscv: cpu_ops_sbi: Add 64bit hartid support on RV64
riscv: dts: sifive: "fix" pmic watchdog node name
riscv: dts: canaan: Add k210 topology information
riscv: dts: sifive: Add fu740 topology information
riscv: dts: sifive: Add fu540 topology information
riscv: dts: starfive: Add JH7100 CPU topology
RISC-V: Add CONFIG_{NON,}PORTABLE
riscv: config: enable SOC_STARFIVE in defconfig
riscv: dts: microchip: Add mpfs' topology information
riscv: Kconfig.socs: Add comments
riscv: Kconfig.erratas: Add comments
...
The initial PolarFire SoC devicetree must have been forked off from
the fu540 one prior to the addition of l2cache controller support being
added there. When the controller node was added to mpfs.dtsi, it was
not hooked up to the CPUs & thus sysfs reports an incorrect cache
configuration. Hook it up.
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-06-25
this is a pull request of 22 patches for net-next/master.
The first 2 patches target the xilinx driver. Srinivas Neeli's patch
adds Transmitter Delay Compensation (TDC) support, a patch by me fixes
a typo.
The next patch is by me and fixes a typo in the m_can driver.
Another patch by me allows the configuration of fixed bit rates
without need for do_set_bittiming callback.
The following 7 patches are by Vincent Mailhol and refactor the
can-dev module and Kbuild, de-inline the can_dropped_invalid_skb()
function, which has grown over the time, and drop outgoing skbs if the
controller is in listen only mode.
Max Staudt's patch fixes a reference in the networking/can.rst
documentation.
Vincent Mailhol provides 2 patches with cleanups for the etas_es58x
driver.
Conor Dooley adds bindings for the mpfs-can to the PolarFire SoC dtsi.
Another patch by me allows the configuration of fixed data bit rates
without need for do_set_data_bittiming callback.
The last 5 patches are by Frank Jungclaus. They prepare the esd_usb
driver to add support for the the CAN-USB/3 device in a later series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
PolarFire SoC /does/ have a SiFive pdma, despite what I suggested as a
conflict resolution to Zong. Somehow the entry fell through the cracks
between versions of my dt patches, so re-add it with Zong's updated
compatible & dma-channels property.
Fixes: c5094f3710 ("riscv: dts: microchip: refactor icicle kit device tree")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Currently mpfs-fabric.dtsi is included by mpfs.dtsi - which is fine
currently since there is only one board with this SoC upstream.
However if another board was added, it would include the fabric contents
of the Icicle Kit's reference design. To avoid this, rename
mpfs-fabric.dtsi to mpfs-icicle-kit-fabric.dtsi & include it in the dts
rather than mpfs.dtsi.
mpfs-icicle-kit-fabric.dtsi specifically matches the 22.03 reference
design for the icicle kit's FPGA fabric & an older version of the
design may not have the i2c or pwm devices - so add the compatible
string to document this.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220509142610.128590-6-conor.dooley@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The MPFS system controller has no registers of its own, so move it out
of the soc node to avoid dtbs_check warnings:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dtb: soc: syscontroller: {'compatible': ['microchip,mpfs-sys-controller'], 'mboxes': [[15, 0]], 'status': ['okay']} should not be valid under {'type': 'object'}
Reported-by: Palmer Dabbelt <palmer@rivosinc.com>
Suggested-by: Rob Herring <robh@kernel.org>
Fixes: 528a5b1f25 ("riscv: dts: microchip: add new peripherals to icicle kit device tree")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220509142610.128590-3-conor.dooley@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The clock properties in the icicle kit's memory entries cause dtbs_check
errors:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dtb: /: memory@80000000: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
Get rid of the clocks to avoid the errors.
Reported-by: Palmer Dabbelt <palmer@rivosinc.com>
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Fixes: 5b28df37d3 ("riscv: dts: microchip: update peripherals in icicle kit device tree")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220509142610.128590-2-conor.dooley@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Pull RISC-V fixes from Palmer Dabbelt:
- fix the fu540-c000 device tree to avoid a schema check failure on the
DMA node name
- fix typo in the PolarFire SOC device tree
* tag 'riscv-for-linus-5.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: dts: microchip: fix gpio1 reg property typo
riscv: dts: sifive: fu540-c000: align dma node name with dtschema
The 600M clock in the fabric is not the real reference, replace it with
a 125M clock which is the correct value for the icicle kit. Rename the
msspllclk node to mssrefclk since this is now the input to, not the
output of, the msspll clock. Control of the msspll clock has been moved
into the clock configurator, so add the register range for it to the clk
configurator. Finally, add a new output of the clock config block which
will provide the 1M reference clock for the MTIMER and the rtc.
Fixes: 528a5b1f25 ("riscv: dts: microchip: add new peripherals to icicle kit device tree")
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220413075835.3354193-10-conor.dooley@microchip.com
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The fic clocks passed to the pcie controller and other peripherals in
the device tree are not the clocks they actually run on. The fics are
actually clock domain crossers & the clock config blocks output is the
mss/cpu side input to the interconnect. The peripherals are actually
clocked by fixed frequency clocks embedded in the fpga fabric.
Fix the device tree so that these peripherals use the correct clocks.
The fabric side FIC0 & FIC1 inputs both use the same 125 MHz, so only
one clock is created for them.
Fixes: 528a5b1f25 ("riscv: dts: microchip: add new peripherals to icicle kit device tree")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220413075835.3354193-4-conor.dooley@microchip.com
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add new peripherals to the MPFS, and enable them in the Icicle kit
device tree:
2x SPI, QSPI, 3x GPIO, 2x I2C, Real Time Counter, PCIE controller,
USB host & system controller.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Assorted minor changes to the MPFS/Icicle kit device tree:
- enable mmuart4 instead of mmuart0
- remove sifive pdma
- split memory node to match updated fpga design
- move stdout path to serial1 to avoid collision with
bootloader running on the e51
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Split the device tree for the Microchip MPFS into two sections by adding
microchip-mpfs-fabric.dtsi, which contains peripherals contained in the
FPGA fabric.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Update the Microchip Icicle kit device tree by replacing clock
related magic numbers with their defined counterparts.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped.
Fix this by grouping the tuples of "interrupts" and
"interrupts-extended" properties using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
"make dtbs_check" reports:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: soc: refclk: {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[600000000]], 'clock-output-names': ['msspllclk'], 'phandle': [[7]]} should not be valid under {'type': 'object'}
From schema: dtschema/schemas/simple-bus.yaml
Fix this by moving the node out of the "soc" subnode.
While at it, rename it to "msspllclk", and drop the now superfluous
"clock-output-names" property.
Move the actual clock-frequency value to the board DTS, since it is not
set until bitstream programming time.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
It does not make sense to have an (empty) chosen node in an SoC-specific
.dtsi, as chosen is meant for system-specific configuration.
It is already provided in microchip-mpfs-icicle-kit.dts anyway.
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
RISC-V DTS changes for v5.16
Cleanups of RISC-V SiFive and Microchip DTSes with dtschema. These are
few minor fixes to make DTSes pass the dtschema, without actual
functional effect.
* tag 'riscv-sifive-dt-5.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
riscv: dts: sifive: add missing compatible for plic
riscv: dts: microchip: add missing compatibles for clint and plic
riscv: dts: sifive: drop duplicated nodes and properties in sifive
riscv: dts: sifive: fix Unleashed board compatible
riscv: dts: sifive: use only generic JEDEC SPI NOR flash compatible
The Microchip Icicle kit uses SiFive E51 and U54 cores, so it looks that
also Core Local Interruptor and Platform-Level Interrupt Controller are
coming from SiFive. Add proper compatibles to silence dtbs_check
warnings:
clint@2000000: compatible:0: 'sifive,clint0' is not one of ['sifive,fu540-c000-clint', 'canaan,k210-clint']
interrupt-controller@c000000: compatible:0: 'sifive,plic-1.0.0' is not one of ['sifive,fu540-c000-plic', 'canaan,k210-plic']
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20210920130412.145231-1-krzysztof.kozlowski@canonical.com
pinctrl-names without pinctrl-0 does not have any sense:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: sdhc@20008000: 'pinctrl-0' is a dependency of 'pinctrl-names'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Devicetree source is a description of hardware and hardware has only one
block @20008000 which can be configured either as eMMC or SDHC. Having
two node for different modes is an obscure, unusual and confusing way to
configure it. Instead the board file is supposed to customize the block
to its needs, e.g. to SDHC mode.
This fixes dtbs_check warning:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: sdhc@20008000: $nodename:0: 'sdhc@20008000' does not match '^mmc(@.*)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
According to bindings, the compatible must include microchip,mpfs. This
fixes dtbs_check warning:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: /: compatible: ['microchip,mpfs-icicle-kit'] is too short
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Currently, nothing is output on the serial console, unless
"console=ttyS0,115200n8" or "earlycon" are appended to the kernel
command line. Enable automatic console selection using
chosen/stdout-path by adding a proper alias, and configure the expected
serial rate.
While at it, add aliases for the other three serial ports, which are
provided on the same micro-USB connector as the first one.
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
U-Boot expects this alias to be in place in order to fix up the mac
address of the ethernet node.
Note on the Icicle Kit board, currently only emac1 is enabled so it
becomes the 'ethernet0'.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Per the DT spec, 'local-mac-address' is used to specify MAC address
that was assigned to the network device, while 'mac-address' is used
to specify the MAC address that was last used by the boot program,
and shall be used only if the value differs from 'local-mac-address'
property value.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: conor dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Fix BUILTIN_DTB config which resulted in a dtb that was actually not
built into the Linux image: in the same manner as Canaan soc does,
create an object file from the dtb file that will get linked into the
Linux image.
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
