Add DTS for ARMv7 based broadband SoC BCM63148. bcm63148.dtsi is the SoC
description DTS header and bcm963148.dts is a simple DTS file for
Broadcom BCM963148 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add DTS for ARMv7 based broadband SoC BCM6756. bcm6756.dtsi is the SoC
description DTS header and bcm96756.dts is a simple DTS file for
Broadcom BCM96756 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add DTS for ARMv7 based broadband SoC BCM6855. bcm6855.dtsi is the SoC
description DTS header and bcm96855.dts is a simple DTS file for
Broadcom BCM96855 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Mercury+ AA1 is not a standalone board, rather it's a module
with an Arria 10 SoC. Remove status = "okay" and i2c aliases, as they
are routed to the base board and should be enabled from there.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Adding a "secure" version of STM32 boards (DK1/DK2/ED1/EV1), SCMI (clock/
reset) protocol and OP-TEE node have been added in SoC dtsi file
(stm32mp151.dtsi). They have been added with a status disabled in order to
keep our legacy unchanged. It is actually not enough to keep our legacy
unchanged.
First, just a reminder about our use case: TF-A (BL2) loads and starts
OP-TEE, then loads and runs U-Boot. U-Boot code checks if an OP-TEE is
running, if yes it searches in Kernel device tree if an OP-TEE node is
present:
-If the OP-TEE node is not present then U-Boot copies OP-TEE node and its
reserved memory region from U-Boot device tree to the kernel device tree.
-If the OP-TEE node is present then it does nothing (this OP-TEE node will
be used by Linux). So U-Boot lets the kernel device tree unchanged thinking
it is correct for an OP-TEE usage. It is the case for our legacy boards,
the OP-TEE node is present (although disabled) but the reserved memory
region is not declared. As no memory region has been reserved for OP-TEE,
the end of DDR is seen by the kernel as free and then used for CMA. But as
OP-TEE is running, this end of DDR is already used by OP-TEE. So as soon as
kernel tries to access to the CMA region OP-TEE raises an error.
To fix it, all OP-TEE node and SCMI is moved in a dedicated file.
Fixes: 40b4157dbd ("ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15")
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Link: https://lore.kernel.org/r/20220613071920.5463-1-alexandre.torgue@foss.st.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The commit feedaacdad ("Input: atmel_mxt_ts - fix up inverted RESET
handler") requires the reset GPIO to have GPIO_ACTIVE_LOW.
Fixes: 1524b27c94 ("ARM: dts: imx6dl-colibri: Move common nodes to SoM dtsi")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Contrary to what was believed at the time, the ramp delay of 150us is not
plenty for the PU LDO with the default step time of 512 pulses of the 24MHz
clock. Measurements have shown that after enabling the LDO the voltage on
VDDPU_CAP jumps to ~750mV in the first step and after that the regulator
executes the normal ramp up as defined by the step size control.
This means it takes the regulator between 360us and 370us to ramp up to
the nominal 1.15V voltage for this power domain. With the old setting of
the ramp delay the power up of the PU GPC domain would happen in the middle
of the regulator ramp with the voltage being at around 900mV. Apparently
this was enough for most units to properly power up the peripherals in the
domain and execute the reset. Some units however, fail to power up properly,
especially when the chip is at a low temperature. In that case any access
to the GPU registers would yield an incorrect result with no way to recover
from this situation.
Change the ramp delay to 380us to cover the measured ramp up time with a
bit of additional slack.
Fixes: 40130d327f ("ARM: dts: imx6qdl: Allow disabling the PU regulator, add a enable ramp delay")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the entry for V3D for bcm2711 (used in the Raspberry Pi 4)
and the associated firmware clock entry.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix a few issue in bcm47622.dtsi file:
- Remove unnecessary cpu_on and cpu_off properties from psci node
- Add the missing gic registers and interrupts property to gic node
- Cosmetic changes
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add DTS for ARMv7 based broadband SoC BCM6846. bcm6846.dtsi is the
SoC description DTS header and bcm96846.dts is a simple DTS file for
Broadcom BCM96846 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment. No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ADC2 is not available as it conflicts with the AD7879 resistive
touchscreen.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct CAN controller comment. It is a MCP2515 rather than a mpc258x.
Fixes: 66d59b678a ("ARM: dts: imx7-colibri: add MCP2515 CAN controller")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each cpu-core is supposed to list its supply separately, add supply for
cpu1.
Fixes: 2d7401f863 ("ARM: dts: imx7d: Add cpu1 supply")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adding no-1-8-v property to usdhc1 to disable +1.8V signaling (UHS-I)
mode on SoM dtsi level.
Clean up no-1-8-v from Aster carrier board dtsi, which is using defaults
from SoM dtsi and is not UHS-I capable.
A carrier board may have a MMC/SD card slot with a switchable power
supply. Add a pinctrl sleep used when the card power is off to avoid
backfeeding to the card and add the "sleep" pinctrl to the usdhc1
controller.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a significant time required for PHY Micrel KSZ8041 to power up.
Add a delay on start-up/wake-up before the FEC starts communicating with
the PHY.
LDO1 takes 6 ms, R39 + C44 takes ~100ms, the KSZ8041 datasheet asks for
~11 ms before starting any programming on the MIIM.
Counting that, add a 200 ms delay to be sure the PHY is ready for
programming. Also, add the same off delay time to give the capacitor
time to discharge in order to properly reset.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move regulators to module-level device tree given they are standard
Colibri functionalities.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move aliases, chosen, extcon and gpio-keys to module-level device tree
given they are standard Colibri functionalities.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pin GPIO1_IO01 externally pulls down, it is required to sequentially
connect this pin (signal WAKE_MICO#) to +3v3 and then disconnect it to
trigger a wakeup interrupt.
Adding the flag GPIO_PULL_DOWN allows the system to be woken up just
connecting the pin GPIO1_IO01 to +3v3.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the MDIO bus with the respective PHY to allow for making changes to
that easier.
While at it also alphabetically re-order properties and improve
indentation.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename display interface to match other modules to make it easier to
use device tree overlays.
The parallel RGB interface (lcdif) and all related stuff turn on in a
device tree overlay. Keep them disabled in the main devicetree.
As these subsystems are provided by module and not a part of boards,
move their definitions into the module-level devicetree.
Disable ad7879 touchscreen which turns on in a devic tree overlay.
Remains it disabled in the main devicetree.
Move Atmel MXT capacitive touch controller device tree nodes from
carrier board to module level and add iomux pinctl groups for both the
Capacitive Touch Adapter (using SODIMM 28/30) and the capacitive touch
connector as found on later carrier boards (using SODIMM 106/107).
Keep touchscreen and display nodes enabled for NAND based i.MX 7
modules, since device tree overlays are not yet supported. For the
Colibri Evaluation Board keep the Capacitive Touch Adapter node
disabled and PWM2, PWM3 enabled instead.
For eMMC based modules keep nodes disabled to work in conjunction with
device tree overlays.
Add the iomuxc pinctrl group for the LVDS transceiver related signals to
use it in a device tree overlay.
While at it also alphabetically re=order them properties.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set #pwm-cells to the default 3 to gain access to the parameter
which allows inverting the PWM signal. This is useful to specify
a backlight which has its highest brightness at 0.
With the change to use the PWM with inverted polarity the PWM signal
is inverted to how it was before this patch.
This changes the meaning of the values in the brightness-levels
property. I.e. the duty-cycle changes from x/255 to (255-x)/255.
Keeping the brightness-levels will then have a big brightness
jump from 0 to 127 duty cycle, the other 6 steps will then be
barely noticeable.
Change the brightness-levels to provide the same brightness-levels
as before.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the pin muxing for MCLK used by the codec to the codec node
instead of placing it inside the audmux pinctrl group.
While no negative effects have been observed this should make sure that
MCLK is provided when the codec driver is probed.
Follows commit fa51e1dc4b ("ARM: dts: imx6qdl-apalis: Fix sgtl5000
detection issue")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
