The identification EEPROM on the BeagleBone Black baseboard is supplied
by VDD_3V3A which is supplied by LDO4 on the PMIC. Map this as per the DT
binding for the EEPROM. Since this supply is always-on this has no
practical impact but it does silence a warning at boot due to using a dummy
regulator.
Signed-off-by: Mark Brown <broonie@kernel.org>
Message-Id: <20220620152150.708664-1-broonie@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The usdhc3 interface is connected to a soldered eMMC chip on all boards
that import this dtsi. Adding these properties speeds up the device probe
during boot.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As explained in Documentation/devicetree/bindings/mmc/mmc-controller.yaml,
the 'enable-sdio-wakeup' property is considered deprecated.
Replace it with the 'wakeup-source' property instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As explained in Documentation/devicetree/bindings/mmc/mmc-controller.yaml,
the 'enable-sdio-wakeup' property is considered deprecated.
Replace it with the 'wakeup-source' property instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull ARM SoC fixes from Arnd Bergmann:
"A number of fixes have accumulated, but they are largely for harmless
issues:
- Several OF node leak fixes
- A fix to the Exynos7885 UART clock description
- DTS fixes to prevent boot failures on TI AM64 and J721s2
- Bus probe error handling fixes for Baikal-T1
- A fixup to the way STM32 SoCs use separate dts files for different
firmware stacks
- Multiple code fixes for Arm SCMI firmware, all dealing with
robustness of the implementation
- Multiple NXP i.MX devicetree fixes, addressing incorrect data in DT
nodes
- Three updates to the MAINTAINERS file, including Florian Fainelli
taking over BCM283x/BCM2711 (Raspberry Pi) from Nicolas Saenz
Julienne"
* tag 'soc-fixes-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
ARM: dts: aspeed: nuvia: rename vendor nuvia to qcom
arm: mach-spear: Add missing of_node_put() in time.c
ARM: cns3xxx: Fix refcount leak in cns3xxx_init
MAINTAINERS: Update email address
arm64: dts: ti: k3-am64-main: Remove support for HS400 speed mode
arm64: dts: ti: k3-j721s2: Fix overlapping GICD memory region
ARM: dts: bcm2711-rpi-400: Fix GPIO line names
bus: bt1-axi: Don't print error on -EPROBE_DEFER
bus: bt1-apb: Don't print error on -EPROBE_DEFER
ARM: Fix refcount leak in axxia_boot_secondary
ARM: dts: stm32: move SCMI related nodes in a dedicated file for stm32mp15
soc: imx: imx8m-blk-ctrl: fix display clock for LCDIF2 power domain
ARM: dts: imx6qdl-colibri: Fix capacitive touch reset polarity
ARM: dts: imx6qdl: correct PU regulator ramp delay
firmware: arm_scmi: Fix incorrect error propagation in scmi_voltage_descriptors_get
firmware: arm_scmi: Avoid using extended string-buffers sizes if not necessary
firmware: arm_scmi: Fix SENSOR_AXIS_NAME_GET behaviour when unsupported
ARM: dts: imx7: Move hsic_phy power domain to HSIC PHY node
soc: bcm: brcmstb: pm: pm-arm: Fix refcount leak in brcmstb_pm_probe
MAINTAINERS: Update BCM2711/BCM2835 maintainer
...
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.
Thank you Amir for the unit and PSU.
Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK Hynix Inc. H5TQ1G63EFR, 1 GBit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 GBit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE (TPS23754 PoE Interface)
WIFI0 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI2 : Broadcom BCM43428 "Air Marshal" 802.11 abgn (1x1:1)
BUTTON: One reset key behind a small hole next to the Ethernet Port
LEDS : One amber (fault), one white (indicator) LED, separate RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM i2c
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has the pin 1 indicator), RX, TX, GND.
Odd stuff:
- uboot does not support lzma compression, but gzip'd uImage/DTB work.
- uboot claims to support FIT, but fails to pass the DTB to the kernel.
Appending the dtb after the kernel image works.
- RGB-controller is supported through an external userspace program.
- The ubi partition contains a "board-config" volume. It stores the
MAC Address (0x66 in binary) and Serial No. (0x7c alpha-numerical).
- SoC's temperature sensor always reports that it is on fire.
This causes the system to immediately shutdown! Looking at reported
"418 degree Celsius" suggests that this sensor is not working.
WIFI:
b43 is able to initialize all three WIFIs @ 802.11bg.
| b43-phy0: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0000:01:00.0: bus1: Switched to core: 0x812
| b43-phy0: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy0: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy0 warning: 5 GHz band is unsupported on this PHY
| b43-phy1: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0001:01:00.0: bus2: Switched to core: 0x812
| b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy1 warning: 5 GHz band is unsupported on this PHY
| b43-phy2: Broadcom 43228 WLAN found (core revision 30)
| bcma-pci-bridge 0002:01:00.0: bus3: Switched to core: 0x812
| b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
| b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
| Broadcom 43xx driver loaded [ Features: NL ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
