- Return error instead of success if DMA mapping of MSI area fails (Jiantao
Zhang)
- Drop tegra194 MSI register save/restore, which is unnecessary since the
DWC core does it (Jisheng Zhang)
- Factor out qcom enable/disable resources code (Dmitry Baryshkov)
- Remove "snps,dw-pcie" from rockchip-dwc DT "compatible" property because
it's not fully compatible with rockchip (Peter Geis)
- Reset rockchip-dwc controller at probe (Peter Geis)
- Add rockchip-dwc INTx support (Peter Geis)
* remotes/lorenzo/pci/dwc:
PCI: rockchip-dwc: Add legacy interrupt support
PCI: rockchip-dwc: Reset core at driver probe
dt-bindings: PCI: Remove fallback from Rockchip DesignWare binding
PCI: qcom-ep: Move enable/disable resources code to common functions
PCI: tegra194: Remove unnecessary MSI enable reg save and restore
PCI: dwc: Fix setting error return on MSI DMA mapping failure
Clear FLR (Function Level Reset) from device capabilities
registers for all physical functions.
During FLR, the Margining Lane Status and Margining Lane Control
registers should not be reset, as per PCIe specification.
However, the controller incorrectly resets these registers upon FLR.
This causes PCISIG compliance FLR test to fail. Hence preventing
all functions from advertising FLR support if flag quirk_disable_flr
is set.
Link: https://lore.kernel.org/r/1635165075-89864-1-git-send-email-pthombar@cadence.com
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to the PCIe standard the PERST# signal (reset-gpio in
fsl,imx* compatible dts) should be kept asserted for at least 100 usec
before the PCIe refclock is stable, should be kept asserted for at
least 100 msec after the power rails are stable and the host should wait
at least 100 msec after it is de-asserted before accessing the
configuration space of any attached device.
From PCIe CEM r2.0, sec 2.6.2
T-PVPERL: Power stable to PERST# inactive - 100 msec
T-PERST-CLK: REFCLK stable before PERST# inactive - 100 usec.
From PCIe r5.0, sec 6.6.1
With a Downstream Port that does not support Link speeds greater than
5.0 GT/s, software must wait a minimum of 100 ms before sending a
Configuration Request to the device immediately below that Port.
Failure to do so could prevent PCIe devices to be working correctly,
and this was experienced with real devices.
Move reset assert to imx6_pcie_assert_core_reset(), this way we ensure
that PERST# is asserted before enabling any clock, move de-assert to the
end of imx6_pcie_deassert_core_reset() after the clock is enabled and
deemed stable and add a new delay of 100 msec just afterward.
Link: https://lore.kernel.org/all/20220211152550.286821-1-francesco.dolcini@toradex.com
Link: https://lore.kernel.org/r/20220404081509.94356-1-francesco.dolcini@toradex.com
Fixes: bb38919ec5 ("PCI: imx6: Add support for i.MX6 PCIe controller")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Pull pci fix from Bjorn Helgaas:
- Fix Hyper-V "defined but not used" build issue added during merge
window (YueHaibing)
* tag 'pci-v5.18-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: hv: Remove unused hv_set_msi_entry_from_desc()
Fix the following build error:
drivers/pci/controller/pci-hyperv.c:769:13: error: ‘hv_set_msi_entry_from_desc’ defined but not used [-Werror=unused-function]
769 | static void hv_set_msi_entry_from_desc(union hv_msi_entry *msi_entry,
The arm64 implementation of hv_set_msi_entry_from_desc() is not used after
d06957d7a6 ("PCI: hv: Avoid the retarget interrupt hypercall in
irq_unmask() on ARM64"), so remove it.
Fixes: d06957d7a6 ("PCI: hv: Avoid the retarget interrupt hypercall in irq_unmask() on ARM64")
Link: https://lore.kernel.org/r/20220317085130.36388-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Boqun Feng <boqun.feng@gmail.com>
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Move the VGA arbiter from drivers/gpu to drivers/pci because it's
PCI-specific, not GPU-specific (Bjorn Helgaas)
- Select the default VGA device consistently whether it's enumerated
before or after VGA arbiter init, which fixes arches that enumerate
PCI devices late (Huacai Chen)
Resource management:
- Support BAR sizes up to 8TB (Dongdong Liu)
PCIe native device hotplug:
- Fix "Command Completed" tracking to avoid spurious timouts when
powering off empty slots (Liguang Zhang)
- Quirk Qualcomm devices that don't implement Command Completed
correctly, again to avoid spurious timeouts (Manivannan Sadhasivam)
Peer-to-peer DMA:
- Add Intel 3rd Gen Intel Xeon Scalable Processors to whitelist
(Michael J. Ruhl)
APM X-Gene PCIe controller driver:
- Revert generic DT parsing changes that broke some machines in the
field (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Allow controller probe to succeed even when no devices currently
present to allow hot-add later (Fabio Estevam)
- Enable power management on i.MX6QP (Richard Zhu)
- Assert CLKREQ# on i.MX8MM so enumeration doesn't hang when no
device is connected (Richard Zhu)
Marvell Aardvark PCIe controller driver:
- Fix MSI and MSI-X support (Marek Behún, Pali Rohár)
- Add support for ERR and PME interrupts (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Add DT binding and support for "num-lanes" (Pali Rohár)
- Add support for INTx interrupts (Pali Rohár)
Microsoft Hyper-V host bridge driver:
- Avoid unnecessary hypercalls when unmasking IRQs on ARM64 (Boqun
Feng)
Qualcomm PCIe controller driver:
- Add SM8450 DT binding and driver support (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Help the controller get to the L1 state since the hardware can't do
it on its own (Marek Vasut)
- Return PCI_ERROR_RESPONSE (~0) for reads that fail on PCIe (Marek
Vasut)
SiFive FU740 PCIe controller driver:
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe (Ben Dooks)
Socionext UniPhier Pro5 controller driver:
- Add NX1 DT binding and driver support (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Restore MSI configuration so MSI works after resume (Jisheng
Zhang)"
* tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
x86/PCI: Add #includes to asm/pci_x86.h
PCI: ibmphp: Remove unused assignments
PCI: cpqphp: Remove unused assignments
PCI: fu740: Remove unused assignments
PCI: kirin: Remove unused assignments
PCI: Remove unused assignments
PCI: Declare pci_filp_private only when HAVE_PCI_MMAP
PCI: Avoid broken MSI on SB600 USB devices
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read which triggered an exception
PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()
PCI: dwc: Restore MSI Receiver mask during resume
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
PCI/VGA: Replace full MIT license text with SPDX identifier
PCI/VGA: Use unsigned format string to print lock counts
PCI/VGA: Log bridge control messages when adding devices
...
- Finish transition to L1 state in rcar_pcie_config_access() because R-Car
can't do it on its own (Marek Vasut)
- Return PCI_ERROR_RESPONSE for reads that trigger PCIe errors (Marek
Vasut)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read which triggered an exception
PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()
- Save pointer to device match data instead of copying it (Dmitry
Baryshkov)
- Add ddrss_sf_tbu flag to device match data instead of checking OF
compatible string (Dmitry Baryshkov)
- Add SM8450 SoC PCIe DT bindings (Dmitry Baryshkov)
- Add SM8450 PCIe support (Dmitry Baryshkov)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Add SM8450 PCIe support
PCI: qcom: Add ddrss_sf_tbu flag
PCI: qcom: Remove redundancy between qcom_pcie and qcom_pcie_cfg
dt-bindings: pci: qcom: Document PCIe bindings for SM8450
- Add Pali Rohár as pci-mvebu.c maintainer (Pali Rohár)
- Make struct pci_bridge_emul_ops const (Pali Rohár)
- Rename PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR to
PCI_BRIDGE_EMUL_NO_PREFMEM_FORWARD since it doesn't apply to BARs (Pali
Rohár)
- Add new flag PCI_BRIDGE_EMUL_NO_IO_FORWARD for bridges that don't support
IO forwarding (Pali Rohár)
- Add Kconfig help text for CONFIG_PCI_MVEBU (Pali Rohár)
- Remove duplicate nports assignment (Pali Rohár)
- Set PCI_BRIDGE_EMUL_NO_IO_FORWARD when IO is unsupported (Pali Rohár)
- Initialize vendor, device and revision of emulated bridge (Pali Rohár)
- Fix Data Link Layer Link Active reporting on emulated bridge (Pali Rohár)
- Rearrange tests in bridge emulation for easier maintenance (Russell King)
- Add emulated bridge support for PCIe extended capabilities (Russell King)
- Add emulated bridge support for bridge Subsystem Vendor ID capability
(Pali Rohár)
- Configure Maximum Link Width based on DT "num-lanes" property (Pali
Rohár)
- Emulate bridge Subsystem Vendor ID capability (Pali Rohár)
- Emulate AER Capability (Pali Rohár)
- Use PCI core bridge->ops and bridge->child_ops to separate config
accesses to Root Port vs downstream devices (Pali Rohár)
- Unmask all INTx interrupts; they're reported via a single shared GIC
source (Pali Rohár)
- Add INTx support (Pali Rohár)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Implement support for legacy INTx interrupts
PCI: mvebu: Fix macro names and comments about legacy interrupts
dt-bindings: PCI: mvebu: Update information about intx interrupts
PCI: mvebu: Use child_ops API
PCI: mvebu: Add support for Advanced Error Reporting registers on emulated bridge
PCI: mvebu: Add support for PCI Bridge Subsystem Vendor ID on emulated bridge
PCI: mvebu: Correctly configure x1/x4 mode
dt-bindings: PCI: mvebu: Add num-lanes property
PCI: pci-bridge-emul: Add support for PCI Bridge Subsystem Vendor ID capability
PCI: pci-bridge-emul: Add support for PCIe extended capabilities
PCI: pci-bridge-emul: Re-arrange register tests
PCI: mvebu: Fix reporting Data Link Layer Link Active on emulated bridge
PCI: mvebu: Update comment for PCI_EXP_LNKCTL register on emulated bridge
PCI: mvebu: Update comment for PCI_EXP_LNKCAP register on emulated bridge
PCI: mvebu: Properly initialize vendor, device and revision of emulated bridge
PCI: mvebu: Set PCI_BRIDGE_EMUL_NO_IO_FORWARD when IO is unsupported
PCI: mvebu: Remove duplicate nports assignment
PCI: mvebu: Add help string for CONFIG_PCI_MVEBU option
PCI: pci-bridge-emul: Add support for new flag PCI_BRIDGE_EMUL_NO_IO_FORWARD
PCI: pci-bridge-emul: Rename PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR to PCI_BRIDGE_EMUL_NO_PREFMEM_FORWARD
PCI: pci-bridge-emul: Make struct pci_bridge_emul_ops as const
MAINTAINERS: Add Pali Rohár as pci-mvebu.c maintainer
- Allow host controller driver to probe successfully (as other drivers do)
even if link is currently down (Fabio Estevam)
- Enable i.MX6QP PCIe power management (Richard Zhu)
- Invoke PHY exit function after PHY power off (Richard Zhu)
- Assert i.MX8MM CLKREQ# even if no device present to avoid boot hangs
(Richard Zhu)
* remotes/lorenzo/pci/imx6:
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: imx6: Enable i.MX6QP PCIe power management support
PCI: imx6: Allow to probe when dw_pcie_wait_for_link() fails
- Avoid retarget interrupt hypercall in irq_unmask() on ARM64 (Boqun Feng)
* remotes/lorenzo/pci/hv:
PCI: hv: Avoid the retarget interrupt hypercall in irq_unmask() on ARM64
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe to workaround enumeration issue on
SiFive Unmatched board (Ben Dooks)
* pci/host/fu740:
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
- Use PCI_INTERRUPT_* definitions from PCI core instead of custom ones
(Pali Rohár)
- Derive MSI number from bit(s) set in PCIE_MSI_STATUS_REG, not from
PCIE_MSI_PAYLOAD_REG (Pali Rohár)
- Align multi-MSI vectors to power of two (Pali Rohár)
- Rewrite IRQ code to use chained IRQ handler (Pali Rohár)
- Check return value of generic_handle_domain_irq() and warn about spurious
interrupts (Pali Rohár)
- Make MSI irq_chip structures static to driver (Marek Behún)
- Make msi_domain_info structure static to driver (Marek Behún)
- Use dev_fwnode() instead of of_node_to_fwnode(dev->of_node) (Marek Behún)
- Refactor unmasking of summary MSI interrupt (Pali Rohár)
- Add support for masking MSI interrupts and leave them masked at setup
(Pali Rohár)
- Set MSI doorbell address to address of struct advk_pcie (Pali Rohár)
- Enable MSI-X support (Pali Rohár)
- Add support for ERR interrupt on emulated bridge (Pali Rohár)
- Fix read of PCI_EXP_RTSTA_PME bit on emulated bridge (Pali Rohár)
- Optimize writing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME on emulated
bridge (Pali Rohár)
- Add support for PME interrupts (Pali Rohár)
- Fix support for PME requester on emulated bridge (Pali Rohár)
- Use separate INTA interrupt for emulated Root Port so PME and AER
interrupt is not shared with downstream devices (Pali Rohár)
- Remove irq_mask_ack() callback for INTx interrupts (Pali Rohár)
- Don't mask legacy INTx interrupts when mapping (Pali Rohár)
- Drop unnecessary "__maybe_unused" from advk_pcie_disable_phy() (Marek
Behún)
- Update comment about why we check for link being up before issuing a
config request (Marek Behún)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Update comment about link going down after link-up
PCI: aardvark: Drop __maybe_unused from advk_pcie_disable_phy()
PCI: aardvark: Don't mask irq when mapping
PCI: aardvark: Remove irq_mask_ack() callback for INTx interrupts
PCI: aardvark: Use separate INTA interrupt for emulated root bridge
PCI: aardvark: Fix support for PME requester on emulated bridge
PCI: aardvark: Add support for PME interrupts
PCI: aardvark: Optimize writing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME on emulated bridge
PCI: aardvark: Fix reading PCI_EXP_RTSTA_PME bit on emulated bridge
PCI: aardvark: Add support for ERR interrupt on emulated bridge
PCI: aardvark: Enable MSI-X support
PCI: aardvark: Fix setting MSI address
PCI: aardvark: Add support for masking MSI interrupts
PCI: aardvark: Refactor unmasking summary MSI interrupt
PCI: aardvark: Use dev_fwnode() instead of of_node_to_fwnode(dev->of_node)
PCI: aardvark: Make msi_domain_info structure a static driver structure
PCI: aardvark: Make MSI irq_chip structures static driver structures
PCI: aardvark: Check return value of generic_handle_domain_irq() when processing INTx IRQ
PCI: aardvark: Rewrite IRQ code to chained IRQ handler
PCI: aardvark: Fix support for MSI interrupts
PCI: aardvark: Fix reading MSI interrupt number
PCI: aardvark: Replace custom PCIE_CORE_INT_* macros with PCI_INTERRUPT_*
fu740_pcie_host_init() assigned "ret", but never used the value. Drop it.
Found by Krzysztof using cppcheck:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/controller/dwc/pcie-fu740.c:227 Variable 'ret' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
hi3660_pcie_phy_init() assigned "pdev", but never used the value. Drop it.
Found by Krzysztof using cppcheck:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/controller/dwc/pcie-kirin.c:336 Variable 'pdev' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The CLKREQ# signal is an open drain, active low signal that is driven
low by the remote Endpoint device. But it might not be driven low if no
Endpoint device is connected.
On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no
Endpoint is connected to assert CLKREQ#.
Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the
PHY can be initialized.
Link: https://lore.kernel.org/r/1645672013-8949-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
In case the controller is transitioning to L1 in rcar_pcie_config_access(),
any read/write access to PCIECDR triggers asynchronous external abort. This
is because the transition to L1 link state must be manually finished by the
driver. The PCIe IP can transition back from L1 state to L0 on its own.
The current asynchronous external abort hook implementation restarts
the instruction which finally triggered the fault, which can be a
different instruction than the read/write instruction which started
the faulting access. Usually the instruction which finally triggers
the fault is one which has some data dependency on the result of the
read/write. In case of read, the read value after fixup is undefined,
while a read value of faulting read should be PCI_ERROR_RESPONSE.
It is possible to enforce the fault using 'isb' instruction placed
right after the read/write instruction which started the faulting
access. Add custom register accessors which perform the read/write
followed immediately by 'isb'.
This way, the fault always happens on the 'isb' and in case of read,
which is located one instruction before the 'isb', it is now possible
to fix up the return value of the read in the asynchronous external
abort hook and make that read return PCI_ERROR_RESPONSE.
Link: https://lore.kernel.org/r/20220312212349.781799-2-marek.vasut@gmail.com
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Pull irqchip updates from Marc Zyngier:
- Add support for the STM32MP13 variant
- Move parent device away from struct irq_chip
- Remove all instances of non-const strings assigned to
struct irq_chip::name, enabling a nice cleanup for VIC and GIC)
- Simplify the Qualcomm PDC driver
- A bunch of SiFive PLIC cleanups
- Add support for a new variant of the Meson GPIO block
- Add support for the irqchip side of the Apple M1 PMU
- Add support for the Apple M1 Pro/Max AICv2 irqchip
- Add support for the Qualcomm MPM wakeup gadget
- Move the Xilinx driver over to the generic irqdomain handling
- Tiny speedup for IPIs on GICv3 systems
- The usual odd cleanups
Link: https://lore.kernel.org/all/20220313105142.704579-1-maz@kernel.org
Vinod writes:
phy-for-5.18
- New support:
- Mediatek tphy support for MT8186
- Qualcomm usb phy support for sc8180x and sc8280xp
- Qualcomm ufs phy support for sc8180x and sc8280xp
- Qualcomm usb phy support for MSM8953
- Cadence D-Phy Rx support
- Sun4i support for USB phy
- Rockchip naneng combo phy support for RK3568
- Qualcomm eDP PHY for sc7280
- Updates:
- wake on support for Synopsis XHCI controllers
- Yamilify Qualcomm USB HS phy binding
- Charger detection support for TI tusb1210
* tag 'phy-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (53 commits)
phy: qcom-qmp: add sc8280xp UFS PHY
dt-bindings: phy: qcom,qmp: add sc8180x and sc8280xp ufs compatibles
phy: qcom-snps: Add sc8280xp support
dt-bindings: phy: qcom,usb-snps-femto-v2: Add sc8180x and sc8280xp
dt-bindings: Revert "dt-bindings: soc: grf: add naneng combo phy register compatible"
phy: dt-bindings: Add Cadence D-PHY Rx bindings
phy: dt-bindings: cdns,dphy: add power-domains property
phy: dt-bindings: Convert Cadence DPHY binding to YAML
phy: cadence: Add Cadence D-PHY Rx driver
dt-bindings: phy: renesas,usb2-phy: Document RZ/V2L phy bindings
Revert "PCI: aardvark: Fix initialization with old Marvell's Arm Trusted Firmware"
Revert "usb: host: xhci: mvebu: make USB 3.0 PHY optional for Armada 3720"
Revert "ata: ahci: mvebu: Make SATA PHY optional for Armada 3720"
phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation
phy: marvell: phy-mvebu-a3700-comphy: Remove port from driver configuration
phy: phy-brcm-usb: fixup BCM4908 support
dt-bindings: phy: mediatek,tphy: Add compatible for MT8192
phy: ti: tusb1210: Add charger detection
phy: ti: tusb1210: Add a delay between power-on and restoring the phy-parameters
phy: ti: tusb1210: Drop tusb->vendor_specific2 != 0 check from tusb1210_power_on()
...
If a host that uses the IP's integrated MSI Receiver lost power
during suspend, we call dw_pcie_setup_rc() to reinit the RC. But
dw_pcie_setup_rc() always sets pp->irq_mask[ctrl] to ~0, so the mask
register is always set as 0xffffffff incorrectly, thus the MSI can't
work after resume.
Fix this issue by moving pp->irq_mask[ctrl] initialization to
dw_pcie_host_init() so we can correctly set the mask reg during both
boot and resume.
Tested-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://lore.kernel.org/r/20211226074019.2556-1-jszhang@kernel.org
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The calls to devm_gpiod_get_optional() have the -gpios at the end of the
name but the GPIO core code is already adding the suffix during the lookup.
This means the PCIe driver is not finding the necessary reset or power
lines to allow initialisation of the PCIe.
Drop the redundant '-gpios' when we look up GPIOs from the DT.
This bug has not been noticed because if U-Boot has setup the GPIO lines
for the hardware when it does the PCIe initialisation (either by booting
from PCIe or user command to access PCIe) then the PCIe will work in Linux.
The U-Boot as supplied by SiFive does not by default initialise any PCIe
component.
Link: https://lore.kernel.org/r/20220221210347.1335004-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On ARM64 Hyper-V guests, SPIs are used for the interrupts of virtual PCI
devices, and SPIs can be managed directly via GICD registers. Therefore
the retarget interrupt hypercall is not needed on ARM64.
An arch-specific interface hv_arch_irq_unmask() is introduced to handle
the architecture level differences on this. For x86, the behavior
remains unchanged, while for ARM64 no hypercall is invoked when
unmasking an irq for virtual PCI devices.
Link: https://lore.kernel.org/r/20220217034525.1687678-1-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Pull irq fix from Thomas Gleixner:
"A single fix for a regression caused by the recent PCI/MSI rework
which resulted in a recursive locking problem in the VMD driver.
The cure is to cache the relevant information upfront instead of
retrieving it at runtime"
* tag 'irq-urgent-2022-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI: vmd: Prevent recursive locking on interrupt allocation
Pull pci fixes from Bjorn Helgaas:
- Fix a merge error that broke PCI device enumeration on mvebu
platforms, including Turris Omnia (Armada 385) (Pali Rohár)
- Avoid using ATS on all AMD Navi10 and Navi14 GPUs because some
VBIOSes don't account for "harvested" (disabled) parts of the chip
when initializing caches (Alex Deucher)
* tag 'pci-v5.17-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken
PCI: mvebu: Fix device enumeration regression
