Pull networking fixes from David Miller:
"Sorry I let so much accumulate, I was in Buffalo and wanted a few
things to cook in my tree for a while before sending to you. Anyways,
it's a lot of little things as usual at this stage in the game"
1) Make bonding MAINTAINERS entry reflect reality, from Andy
Gospodarek.
2) Fix accidental sock_put() on timewait mini sockets, from Eric
Dumazet.
3) Fix crashes in l2tp due to mis-handling of ipv4 mapped ipv6
addresses, from François CACHEREUL.
4) Fix heap overflow in __audit_sockaddr(), from the eagle eyed Dan
Carpenter.
5) tcp_shifted_skb() doesn't take handle FINs properly, from Eric
Dumazet.
6) SFC driver bug fixes from Ben Hutchings.
7) Fix TX packet scheduling wedge after channel change in ath9k driver,
from Felix Fietkau.
8) Fix user after free in BPF JIT code, from Alexei Starovoitov.
9) Source address selection test is reversed in
__ip_route_output_key(), fix from Jiri Benc.
10) VLAN and CAN layer mis-size netlink attributes, from Marc
Kleine-Budde.
11) Fix permission checks in sysctls to use current_euid() instead of
current_uid(). From Eric W Biederman.
12) IPSEC policies can go away while a timer is still pending for them,
add appropriate ref-counting to fix, from Steffen Klassert.
13) Fix mis-programming of FDR and RMCR registers on R8A7740 sh_eth
chips, from Nguyen Hong Ky and Simon Horman.
14) MLX4 forgets to DMA unmap pages on RX, fix from Amir Vadai.
15) IPV6 GRE tunnel MTU upper limit is miscalculated, from Oussama
Ghorbel.
16) Fix typo in fq_change(), we were assigning "initial quantum" to
"quantum". From Eric Dumazet.
17) Set a more appropriate sk_pacing_rate for non-TCP sockets, otherwise
FQ packet scheduler does not pace those flows properly. Also from
Eric Dumazet.
18) rtlwifi miscalculates packet pointers, from Mark Cave-Ayland.
19) l2tp_xmit_skb() can be called from process context, not just softirq
context, so we must always make sure to BH disable around it. From
Eric Dumazet.
20) On qdisc reset, we forget to purge the RB tree of SKBs in netem
packet scheduler. From Stephen Hemminger.
21) Fix info leak in farsync WAN driver ioctl() handler, from Dan
Carpenter and Salva Peiró.
22) Fix PHY reset and other issues in dm9000 driver, from Nikita
Kiryanov and Michael Abbott.
23) When hardware can do SCTP crc32 checksums, we accidently don't
disable the csum offload when IPSEC transformations have been
applied. From Fan Du and Vlad Yasevich.
24) Tail loss probing in TCP leaves the socket in the wrong congestion
avoidance state. From Yuchung Cheng.
25) In CPSW driver, enable NAPI before interrupts are turned on, from
Markus Pargmann.
26) Integer underflow and dual-assignment in YAM hamradio driver, from
Dan Carpenter.
27) If we are going to mangle a packet in tcp_set_skb_tso_segs() we must
unclone it. This fixes various hard to track down crashes in
drivers where the SKBs ->gso_segs was changing right from underneath
the driver during TX queueing. From Eric Dumazet.
28) Fix the handling of VLAN IDs, and in particular the special IDs 0
and 4095, in the bridging layer. From Toshiaki Makita.
29) Another info leak, this time in wanxl WAN driver, from Salva Peiró.
30) Fix race in socket credential passing, from Daniel Borkmann.
31) WHen NETLABEL is disabled, we don't validate CIPSO packets properly,
from Seif Mazareeb.
32) Fix identification of fragmented frames in ipv4/ipv6 UDP
Fragmentation Offload output paths, from Jiri Pirko.
33) Virtual Function fixes in bnx2x driver from Yuval Mintz and Ariel
Elior.
34) When we removed the explicit neighbour pointer from ipv6 routes a
slight regression was introduced for users such as IPVS, xt_TEE, and
raw sockets. We mix up the users requested destination address with
the routes assigned nexthop/gateway. From Julian Anastasov and
Simon Horman.
35) Fix stack overruns in rt6_probe(), the issue is that can end up
doing two full packet xmit paths at the same time when emitting
neighbour discovery messages. From Hannes Frederic Sowa.
36) davinci_emac driver doesn't handle IFF_ALLMULTI correctly, from
Mariusz Ceier.
37) Make sure to set TCP sk_pacing_rate after the first legitimate RTT
sample, from Neal Cardwell.
38) Wrong netlink attribute passed to xfrm_replay_verify_len(), from
Steffen Klassert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
ax88179_178a: Add VID:DID for Samsung USB Ethernet Adapter
ax88179_178a: Correct the RX error definition in RX header
Revert "bridge: only expire the mdb entry when query is received"
tcp: initialize passive-side sk_pacing_rate after 3WHS
davinci_emac.c: Fix IFF_ALLMULTI setup
mac802154: correct a typo in ieee802154_alloc_device() prototype
ipv6: probe routes asynchronous in rt6_probe
netfilter: nf_conntrack: fix rt6i_gateway checks for H.323 helper
ipv6: fill rt6i_gateway with nexthop address
ipv6: always prefer rt6i_gateway if present
bnx2x: Set NETIF_F_HIGHDMA unconditionally
bnx2x: Don't pretend during register dump
bnx2x: Lock DMAE when used by statistic flow
bnx2x: Prevent null pointer dereference on error flow
bnx2x: Fix config when SR-IOV and iSCSI are enabled
bnx2x: Fix Coalescing configuration
bnx2x: Unlock VF-PF channel on MAC/VLAN config error
bnx2x: Prevent an illegal pointer dereference during panic
bnx2x: Fix Maximum CoS estimation for VFs
drivers: net: cpsw: fix kernel warn during iperf test with interrupt pacing
...
Correct the definition of AX_RXHDR_CRC_ERR and
AX_RXHDR_DROP_ERR. They are BIT29 and BIT31 in pkt_hdr
seperately.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IFF_ALLMULTI flag is set on interface and IFF_PROMISC isn't,
emac_dev_mcast_set should only enable RX of multicasts and reset
MACHASH registers.
It does this, but afterwards it either sets up multicast MACs
filtering or disables RX of multicasts and resets MACHASH registers
again, rendering IFF_ALLMULTI flag useless.
This patch fixes emac_dev_mcast_set, so that multicast MACs filtering and
disabling of RX of multicasts are skipped when IFF_ALLMULTI flag is set.
Tested with kernel 2.6.37.
Signed-off-by: Mariusz Ceier <mceier+kernel@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver implementation incorrectly sets the flag only if 64-bit
DMA mask succeeded.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of a register dump, the interface pretends to have the identity
of other interfaces of the same physical device in order to perform
HW configuration for them - specifically, it needs to prevent attentions
from generating on those functions as the register dump accesses registers
in common blocks which whose reading might generate an attention.
However, such pretension is unsafe - unlike other flows in which the driver
uses pretend, during register dump there is no guarantee no other HW access
will take place (by other flows). If such access will take place, the HW will
be accessed by the wrong interface, and leave both functions in an incorrect
state.
This patch removes all pretensions from the register dump flow. Instead, it
changes initial configuration of attentions such that no fatal attention will
be generated for other functions as a result of the register dump
(notice however, a debug print claiming an attention from other functions IS
possible during the register dump)
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x has several clients to its DMAE machines - all of them with the exception
of the statistics flow used the same locking mechanisms to synchronize the DMAE
machines' usage.
Since statistics (which are periodically entered) use DMAE without taking the
locks, they may erase the commands which were previously set -
e.g., it may cause a VF to timeout while waiting for a PF answer on the VF-PF
channel as that command header would have been overwritten by the statistics'
header.
This patch makes certain that all flows utilizing DMAE will use the same
API, assuring that the locking scheme will be kept by all said flows.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If debug message is open and bnx2x_vfop_qdtor_cmd() were to fail,
the resulting print would have caused a null pointer dereference.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit b9871bc "bnx2x: VF RSS support - PF side", if a PF will
have SR-IOV supported in its PCI configuration space, storage drivers will not
work for that interface.
This patch fixes the resource calculation to allow such a configuration to
properly work.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x drivers configure coalescing incorrectly (e.g., as a result of a call
to 'ethtool -c'). Although this is almost invisible to the user (due to NAPI)
designated tests will show the configuration is incorrect.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code returns upon failure, leaving the VF-PF in an unusable state;
This patch adds the missing release so further commands could pass between
PF and VF.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a panic, the driver tries to print the Management FW buffer of recent
commands. To do so, the driver reads the address of that buffer from a known
address. If the buffer is unavailable (e.g., PCI reads don't work, MCP is
failing, etc.), the driver will try to access the address it has read, possibly
causing a kernel panic.
This check 'sanitizes' the access, validating the read value is indeed a valid
address inside the management FW's buffers.
The patch also removes a read outside the scope of the buffer, which resulted
in some unrelated chraracters appearing in the log.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x VFs do not support Multi-CoS; Current implementation
erroneously sets the VFs maximal number of CoS to be > 1.
This will cause the driver to call alloc_etherdev_mqs() with
a number of queues it cannot possibly support and reflects
in 'odd' driver prints.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o validate Tx queue only in case of adapters which supports
multi Tx queue.
This patch is to fix regression introduced in commit
aa4a1f7df7
"qlcnic: Enable Tx queue changes using ethtool for 82xx Series adapter"
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a required field for all TX_CREATE cmd versions > 0.
This fixes a driver initialization failure, caused by recent SH-R Firmwares
(versions > 10.0.639.0) failing the TX_CREATE cmd when if_id field is
not passed.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wanxl_ioctl() code fails to initialize the two padding bytes of
struct sync_serial_settings after the ->loopback member. Add an explicit
memset(0) before filling the structure to avoid the info leak.
Signed-off-by: Salva Peiró <speiro@ai2.upv.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.12 stream!
For the mac80211 bits, Johannes says:
"Jouni fixes a remain-on-channel vs. scan bug, and Felix fixes client TX
probing on VLANs."
And also:
"This time I have two fixes from Emmanuel for RF-kill issues, and fixed
two issues reported by Evan Huus and Thomas Lindroth respectively."
On top of those...
Avinash Patil adds a couple of mwifiex fixes to properly inform cfg80211
about some different types of disconnects, avoiding WARNINGs.
Mark Cave-Ayland corrects a pointer arithmetic problem in rtlwifi,
avoiding incorrect automatic gain calculations.
Solomon Peachy sends a cw1200 fix for locking around calls to
cw1200_irq_handler, addressing "lost interrupt" problems.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a QMI device, manufactured by TCT Mobile Phones.
A companion patch blacklisting this device's QMI interface in the option.c
driver has been sent.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to schedule the refill work unconditionally after changing the
number of queues. This may lead an issue if the device is not
up. Since we only try to cancel the work in ndo_stop(), this may cause
the refill work still work after removing the device. Fix this by only
schedule the work when device is up.
The bug were introduce by commit 9b9cd8024a.
(virtio-net: fix the race between channels setting and refill)
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're trying to re-configure the affinity unconditionally in cpu hotplug
callback. This may lead the issue during resuming from s3/s4 since
- virt queues haven't been allocated at that time.
- it's unnecessary since thaw method will re-configure the affinity.
Fix this issue by checking the config_enable and do nothing is we're not ready.
The bug were introduced by commit 8de4b2f3ae
(virtio-net: reset virtqueue affinity when doing cpu hotplug).
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We overwrite the ->bitrate with the user supplied information on the
next line.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If interrupts happen before napi_enable was called, the driver will not
work as expected. Network transmissions are impossible in this state.
This bug can be reproduced easily by restarting the network interface in
a loop. After some time any network transmissions on the network
interface will fail.
This patch fixes the bug by enabling napi before enabling the network
interface interrupts.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPS support is kind of broken on bnx2x, because only non LRO packets
get proper rx queue information. This triggers reorders, as it seems
bnx2x like to generate a non LRO packet for segment including TCP PUSH
flag : (this might be pure coincidence, but all the reorders I've
seen involve segments with a PUSH)
11:13:34.335847 IP A > B: . 415808:447136(31328) ack 1 win 457 <nop,nop,timestamp 3789336 3985797>
11:13:34.335992 IP A > B: . 447136:448560(1424) ack 1 win 457 <nop,nop,timestamp 3789336 3985797>
11:13:34.336391 IP A > B: . 448560:479888(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985797>
11:13:34.336425 IP A > B: P 511216:512640(1424) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
11:13:34.336423 IP A > B: . 479888:511216(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
11:13:34.336924 IP A > B: . 512640:543968(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
11:13:34.336963 IP A > B: . 543968:575296(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
We must call skb_record_rx_queue() to properly give to RPS (and more
generally for TX queue selection on forward path) the receive queue
information.
Similar fix is needed for skb_mark_napi_id(), but will be handled
in a separate patch to ease stable backports.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENOMEM in the padding pkt alloc fail error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the LPA by checking mii_if_info, instead of just saying "no LPA" every
time.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Davicom application note for the DM9000 network device recommends
performing software reset twice to correctly initialise the device.
Without this reset some devices fail to initialise correctly on
system startup.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take the phy out of reset explicitly during system resume to avoid
losing network connectivity.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the changes introduced in commit 6741f40 (DM9000B: driver
initialization upgrade) break functionality on DM9000A
(error message during NFS boot: "dm9000 dm9000.0: eth0: link down")
Since the changes were meant to serve only DM9000B, make them
dependent on the chip type.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
one trivial semicolon cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=0XuA
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Last batch of IB changes for 3.12: many mlx5 hardware driver fixes
plus one trivial semicolon cleanup"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Remove unnecessary semicolons
IB/mlx5: Ensure proper synchronization accessing memory
IB/mlx5: Fix alignment of reg umr gather buffers
IB/mlx5: Fix eq names to display nicely in /proc/interrupts
mlx5: Fix error code translation from firmware to driver
IB/mlx5: Fix opt param mask according to firmware spec
mlx5: Fix opt param mask for sq err to rts transition
IB/mlx5: Disable atomic operations
mlx5: Fix layout of struct mlx5_init_seg
mlx5: Keep polling to reclaim pages while any returned
IB/mlx5: Avoid async events on invalid port number
IB/mlx5: Decrease memory consumption of mr caches
mlx5: Remove checksum on command interface commands
IB/mlx5: Fix memory leak in mlx5_ib_create_srq
IB/mlx5: Flush cache workqueue before destroying it
IB/mlx5: Fix send work queue size calculation
This patch adds missing cfg80211_disconnected event for P2P client
interface upon successful deauthenticate command, deauthenticate
event or disassociate event from FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If device is surprise removed, commands sent to FW including
deauthenticate command fail as bus writes fail.
We update our media_connected status to false and inform cfg80211
about disconnection only when command is successful. Since cfg80211
assumes device is still connected, it results into following
WARN_ON during unload:
WARNING: CPU: 0 PID: 18245 at net/wireless/core.c:937
cfg80211_netdev_notifier_call+0x175/0x4d0 [cfg80211]()
Avoid this by emitting cfg80211_disconnected event even if the
deauthenticate command fails.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SMC_outw invokes an endian-aware I/O accessor, which may change the data
endianness before writing to the device. This is not suitable for data
transfers where the memory buffer is simply a string of bytes that does
not require any byte-swapping.
This patches fixes the smc91x SMC_PUSH_DATA macro so that it uses the
string I/O accessor for outputting the leading or trailing halfwords on
halfword-aligned buffers.
Cc: <netdev@vger.kernel.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fst_get_iface() code fails to initialize the two padding bytes of
struct sync_serial_settings after the ->loopback member. Add an explicit
memset(0) before filling the structure to avoid the info leak.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nguyen Hong Ky posted a patch to correct RX packet errors on R8A7740 which
was applied as 2c6221e4a5 ("net: sh_eth: Fix RX packets errors on
R8A7740"). Unfortunately sh_eth.c contains many similar instances
of struct sh_eth_cpu_data and the patch was miss-applied, updating
sh7734_data instead of r8a7740_data.
This patch corrects this problem by.
1. Reverting the change to sh7734_data and;
2. Applying the change to r8a7740_data.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes "lost interrupt" problems that occurred on SPI-based systems.
cw1200_irq_handler() expects the hwbus to be locked, but on the
SPI-path, that lock wasn't taken (unlike in the SDIO-path, where the
generic SDIO-code takes care of acquiring the lock).
Cc: stable@vger.kernel.org
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An error in calculating the offset in an skb causes the driver to read
essential device info from the wrong locations. The main effect is that
automatic gain calculations are nonsense.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's helpful for a driver to put the pci slot name in its interrupt
names, so /proc/interrupts will show the pci slot of the device.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Change mlx5_reclaim_startup_pages() to keep polling while any pages
are returned. If none are returned, keep polling for five more seconds
before exiting with an error message.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Checksum calculations consume CPU resources and can be significant to
the rate of resource creation/destruction.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In commit:
3078cde7 can: at91_can: add dt support
device tree support was added to the at91_can driver. In this commit the
mapping of device to driver data was mixed up. This results in the sam9x5
parameters being used for the sam9263 and the workaround for the broken mailbox
0 on the sam9263 not being activated.
This patch fixes the broken platform_device_id table.
Cc: linux-stable <stable@vger.kernel.org>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The current implemetation of of_match_device() relies that the of_device_id
table in the driver is sorted from most specific to least specific compatible.
Without this patch the mx28 is detected as the less specific p1010. This leads
to a p1010 specific workaround is activated on the mx28, which is not needed.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In patch
0d1862e can: flexcan: fix flexcan_chip_start() on imx6
the loop in flexcan_chip_start() that iterates over all mailboxes after the
soft reset of the CAN core was removed. This loop put all mailboxes (even the
ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63,
this aborts any pending TX messages.
After a cold boot there is random garbage in the mailboxes, which leads to
spontaneous transmit of CAN frames during first activation. Further if the
interface was disabled with a pending message (usually due to an error
condition on the CAN bus), this message is retransmitted after enabling the
interface again.
This patch fixes the regression by:
1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX
FIFO, 8 is used by TX.
2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that
mailbox is aborted.
Cc: linux-stable <stable@vger.kernel.org>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
John W. Linville says:
===================
Please pull this batch of fixes intended for 3.12...
Most of the bits are for iwlwifi -- Johannes says:
"I have a fix for WoWLAN/D3, a PCIe device fix, we're removing a
warning, there's a fix for RF-kill while scanning (which goes together
with a mac80211 fix) and last but not least we have many new PCI IDs."
Also for iwlwifi is a patch from Johannes to correct some merge damage
that crept into the tree before the last merge window.
On top of that, Felix Fietkau sends an ath9k patch to avoid a Tx
scheduling hang when changing channels to do a scan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable workaround for P2020/P2010 erratum eTSEC 20,
"Excess delays when transmitting TOE=1 large frames".
The impact is that frames lager than 2500-bytes for which
TOE (i.e. TCP/IP hw accelerations like Tx csum) is enabled
may see excess delay before start of transmission.
This erratum was fixed in Rev 2.0.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros and defines from mpc85xx.h to simplify
and prevent errors in identifying a mpc85xx based SoC
for errata detection.
This should help enabling (and identifying) workarounds
for various mpc85xx based chips and revisions.
For instance, express MPC8548 Rev.2 as:
(SVR_SOC_VER(svr) == SVR_8548) && (SVR_REV(svr) == 0x20)
instead of:
(pvr == 0x80210020 && mod == 0x8030 && rev == 0x0020)
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A002 is still in "no plans to fix" state, and applies to all
the current P1/P2 parts as well, so it's resonable to enable
its workaround by default, for all the soc's with etsec.
The impact of not enabling this workaround for affected parts
is that under certain conditons (runt frames or even frames
with RX error detected at PHY level) during controller reset,
the controller might fail to indicate Rx reset (GRS) completion.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
