The inode delalloc mutex was added a long time ago by commit f248679e86
("Btrfs: add a delalloc mutex to inodes for delalloc reservations"), and
the reason for its introduction is not very clear from the change log. It
claims it solves bogus warnings from lockdep, however it lacks an example
report/warning from lockdep, or any explanation.
Since we have enough concurrentcy protection from the locks of the space
info and block reserve objects, and such lockdep warnings don't seem to
exist anymore (at least on a 5.3 kernel I couldn't get them with fstests,
ltp, fs_mark, etc), remove it, simplifying things a bit and decreasing
the size of the btrfs_inode structure. With some quick fio tests doing
direct IO and mmap writes I couldn't observe any significant performance
increase either (direct IO writes that don't increase the file's size
don't hold the inode's lock for their entire duration and mmap writes
don't hold the inode's lock at all), which are the only type of writes
that could see any performance gain due to less serialization.
Review feedback from Josef:
The problem was taking the i_mutex in mmap, which is how I was
protecting delalloc reservations originally. The delalloc mutex didn't
come with all of the other dependencies. That's what the lockdep
messages were about, removing the lock isn't going to make them appear
again.
We _had_ to lock around this because we used to do tricks to keep from
over-reserving, and if we didn't serialize delalloc reservations we'd
end up with ugly accounting problems when we tried to clean things up.
However with my recentish changes this isn't the case anymore. Every
operation is responsible for reserving its space, and then adding it to
the inode. Then cleaning up is straightforward and can't be mucked up
by other users. So we no longer need the delalloc mutex to safe us from
ourselves.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
To remove use of extent_map::bdev we need to find a replacement, and the
latest_bdev is the only one we can use here, because inode::i_bdev and
superblock::s_bdev are NULL.
The DIO code uses bdev in two places:
* to read blocksize to perform alignment checks in
do_blockdev_direct_IO, but we do them in btrfs code before any call to
DIO
* in the following call chain:
do_direct_IO
get_more_blocks
sdio->get_block() <-- this is btrfs_get_blocks_direct
subsequently the map_bh->b_dev member is used in clean_bdev_aliases
and dio_new_bio to set the bio's bdev to that of the buffer_head.
However, because we have provided a submit function dio_bio_submit
calls our submission function and ignores the bdev.
So it's safe to pass any valid bdev that's used within the filesystem.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In the fixup worker, if we fail to mark the range as delalloc in the io
tree, we must release the previously reserved metadata, as well as update
the outstanding extents counter for the inode, otherwise we leak metadata
space.
In pratice we can't return an error from btrfs_set_extent_delalloc(),
which is just a wrapper around __set_extent_bit(), as for most errors
__set_extent_bit() does a BUG_ON() (or panics which hits a BUG_ON() as
well) and returning an -EEXIST error doesn't happen in this case since
the exclusive bits parameter always has a value of 0 through this code
path. Nevertheless, just fix the error handling in the fixup worker,
in case one day __set_extent_bit() can return an error to this code
path.
Fixes: f3038ee3a3 ("btrfs: Handle btrfs_set_extent_delalloc failure in fixup worker")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function is used only during the final phase of freespace cache
writeout. This is necessary since using the plain btrfs_join_transaction
api is deadlock prone. The deadlock looks like:
T1:
btrfs_commit_transaction
commit_cowonly_roots
btrfs_write_dirty_block_groups
btrfs_wait_cache_io
__btrfs_wait_cache_io
btrfs_wait_ordered_range <-- Triggers ordered IO for freespace
inode and blocks transaction commit
until freespace cache writeout
T2: <-- after T1 has triggered the writeout
finish_ordered_fn
btrfs_finish_ordered_io
btrfs_join_transaction <--- this would block waiting for current
transaction to commit, but since trans
commit is waiting for this writeout to
finish
The special purpose functions prevents it by simply skipping the "wait
for writeout" since it's guaranteed the transaction won't proceed until
we are done.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Async CRCs and compression submit IO through helper threads, which means
they have IO priority inversions when cgroup IO controllers are in use.
This flags all of the writes submitted by btrfs helper threads as
REQ_CGROUP_PUNT. submit_bio() will punt these to dedicated per-blkcg
work items to avoid the priority inversion.
For the compression code, we take a reference on the wbc's blkg css and
pass it down to the async workers.
For the async CRCs, the bio already has the correct css, we just need to
tell the block layer to use REQ_CGROUP_PUNT.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Chris Mason <clm@fb.com>
Modified-and-reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David Sterba <dsterba@suse.com>
The btrfs writepages function collects a large range of pages flagged
for delayed allocation, and then sends them down through the COW code
for processing. When compression is on, we allocate one async_chunk
structure for every 512K, and then run those pages through the
compression code for IO submission.
writepages starts all of this off with a single page, locked by the
original call to extent_write_cache_pages(), and it's important to keep
track of this page because it has already been through
clear_page_dirty_for_io().
The btrfs async_chunk struct has a pointer to the locked_page, and when
we're redirtying the page because compression had to fallback to
uncompressed IO, we use page->index to decide if a given async_chunk
struct really owns that page.
But, this is racey. If a given delalloc range is broken up into two
async_chunks (chunkA and chunkB), we can end up with something like
this:
compress_file_range(chunkA)
submit_compress_extents(chunkA)
submit compressed bios(chunkA)
put_page(locked_page)
compress_file_range(chunkB)
...
Or:
async_cow_submit
submit_compressed_extents <--- falls back to buffered writeout
cow_file_range
extent_clear_unlock_delalloc
__process_pages_contig
put_page(locked_pages)
async_cow_submit
The end result is that chunkA is completed and cleaned up before chunkB
even starts processing. This means we can free locked_page() and reuse
it elsewhere. If we get really lucky, it'll have the same page->index
in its new home as it did before.
While we're processing chunkB, we might decide we need to fall back to
uncompressed IO, and so compress_file_range() will call
__set_page_dirty_nobufers() on chunkB->locked_page.
Without cgroups in use, this creates as a phantom dirty page, which
isn't great but isn't the end of the world. What can happen, it can go
through the fixup worker and the whole COW machinery again:
in submit_compressed_extents():
while (async extents) {
...
cow_file_range
if (!page_started ...)
extent_write_locked_range
else if (...)
unlock_page
continue;
This hasn't been observed in practice but is still possible.
With cgroups in use, we might crash in the accounting code because
page->mapping->i_wb isn't set.
BUG: unable to handle kernel NULL pointer dereference at 00000000000000d0
IP: percpu_counter_add_batch+0x11/0x70
PGD 66534e067 P4D 66534e067 PUD 66534f067 PMD 0
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
CPU: 16 PID: 2172 Comm: rm Not tainted
RIP: 0010:percpu_counter_add_batch+0x11/0x70
RSP: 0018:ffffc9000a97bbe0 EFLAGS: 00010286
RAX: 0000000000000005 RBX: 0000000000000090 RCX: 0000000000026115
RDX: 0000000000000030 RSI: ffffffffffffffff RDI: 0000000000000090
RBP: 0000000000000000 R08: fffffffffffffff5 R09: 0000000000000000
R10: 00000000000260c0 R11: ffff881037fc26c0 R12: ffffffffffffffff
R13: ffff880fe4111548 R14: ffffc9000a97bc90 R15: 0000000000000001
FS: 00007f5503ced480(0000) GS:ffff880ff7200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000d0 CR3: 00000001e0459005 CR4: 0000000000360ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
account_page_cleaned+0x15b/0x1f0
__cancel_dirty_page+0x146/0x200
truncate_cleanup_page+0x92/0xb0
truncate_inode_pages_range+0x202/0x7d0
btrfs_evict_inode+0x92/0x5a0
evict+0xc1/0x190
do_unlinkat+0x176/0x280
do_syscall_64+0x63/0x1a0
entry_SYSCALL_64_after_hwframe+0x42/0xb7
The fix here is to make asyc_chunk->locked_page NULL everywhere but the
one async_chunk struct that's allowed to do things to the locked page.
Link: https://lore.kernel.org/linux-btrfs/c2419d01-5c84-3fb4-189e-4db519d08796@suse.com/
Fixes: 771ed689d2 ("Btrfs: Optimize compressed writeback and reads")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Chris Mason <clm@fb.com>
[ update changelog from mail thread discussion ]
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_schedule_bio() hands IO off to a helper thread to do the actual
submit_bio() call. This has been used to make sure async crc and
compression helpers don't get stuck on IO submission. To maintain good
performance, over time the IO submission threads duplicated some IO
scheduler characteristics such as high and low priority IOs and they
also made some ugly assumptions about request allocation batch sizes.
All of this cost at least one extra context switch during IO submission,
and doesn't fit well with the modern blkmq IO stack. So, this commit stops
using btrfs_schedule_bio(). We may need to adjust the number of async
helper threads for crcs and compression, but long term it's a better
path.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The parameter is now always set to NULL and could be dropped. The last
user was get_default_root but that got reworked in 05dbe6837b ("Btrfs:
unify subvol= and subvolid= mounting") and the parameter became unused.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit 9e0af23764 ("Btrfs: fix task hang under heavy compressed
write") worked around the issue that a recycled work item could get a
false dependency on the original work item due to how the workqueue code
guarantees non-reentrancy. It did so by giving different work functions
to different types of work.
However, the fixes in the previous few patches are more complete, as
they prevent a work item from being recycled at all (except for a tiny
window that the kernel workqueue code handles for us). This obsoletes
the previous fix, so we don't need the unique helpers for correctness.
The only other reason to keep them would be so they show up in stack
traces, but they always seem to be optimized to a tail call, so they
don't show up anyways. So, let's just get rid of the extra indirection.
While we're here, rename normal_work_helper() to the more informative
btrfs_work_helper().
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
During rename exchange we might have successfully log the new name in the
source root's log tree, in which case we leave our log context (allocated
on stack) in the root's list of log contextes. However we might fail to
log the new name in the destination root, in which case we fallback to
a transaction commit later and never sync the log of the source root,
which causes the source root log context to remain in the list of log
contextes. This later causes invalid memory accesses because the context
was allocated on stack and after rename exchange finishes the stack gets
reused and overwritten for other purposes.
The kernel's linked list corruption detector (CONFIG_DEBUG_LIST=y) can
detect this and report something like the following:
[ 691.489929] ------------[ cut here ]------------
[ 691.489947] list_add corruption. prev->next should be next (ffff88819c944530), but was ffff8881c23f7be4. (prev=ffff8881c23f7a38).
[ 691.489967] WARNING: CPU: 2 PID: 28933 at lib/list_debug.c:28 __list_add_valid+0x95/0xe0
(...)
[ 691.489998] CPU: 2 PID: 28933 Comm: fsstress Not tainted 5.4.0-rc6-btrfs-next-62 #1
[ 691.490001] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c8995f-prebuilt.qemu.org 04/01/2014
[ 691.490003] RIP: 0010:__list_add_valid+0x95/0xe0
(...)
[ 691.490007] RSP: 0018:ffff8881f0b3faf8 EFLAGS: 00010282
[ 691.490010] RAX: 0000000000000000 RBX: ffff88819c944530 RCX: 0000000000000000
[ 691.490011] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffffffffa2c497e0
[ 691.490013] RBP: ffff8881f0b3fe68 R08: ffffed103eaa4115 R09: ffffed103eaa4114
[ 691.490015] R10: ffff88819c944000 R11: ffffed103eaa4115 R12: 7fffffffffffffff
[ 691.490016] R13: ffff8881b4035610 R14: ffff8881e7b84728 R15: 1ffff1103e167f7b
[ 691.490019] FS: 00007f4b25ea2e80(0000) GS:ffff8881f5500000(0000) knlGS:0000000000000000
[ 691.490021] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 691.490022] CR2: 00007fffbb2d4eec CR3: 00000001f2a4a004 CR4: 00000000003606e0
[ 691.490025] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 691.490027] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 691.490029] Call Trace:
[ 691.490058] btrfs_log_inode_parent+0x667/0x2730 [btrfs]
[ 691.490083] ? join_transaction+0x24a/0xce0 [btrfs]
[ 691.490107] ? btrfs_end_log_trans+0x80/0x80 [btrfs]
[ 691.490111] ? dget_parent+0xb8/0x460
[ 691.490116] ? lock_downgrade+0x6b0/0x6b0
[ 691.490121] ? rwlock_bug.part.0+0x90/0x90
[ 691.490127] ? do_raw_spin_unlock+0x142/0x220
[ 691.490151] btrfs_log_dentry_safe+0x65/0x90 [btrfs]
[ 691.490172] btrfs_sync_file+0x9f1/0xc00 [btrfs]
[ 691.490195] ? btrfs_file_write_iter+0x1800/0x1800 [btrfs]
[ 691.490198] ? rcu_read_lock_any_held.part.11+0x20/0x20
[ 691.490204] ? __do_sys_newstat+0x88/0xd0
[ 691.490207] ? cp_new_stat+0x5d0/0x5d0
[ 691.490218] ? do_fsync+0x38/0x60
[ 691.490220] do_fsync+0x38/0x60
[ 691.490224] __x64_sys_fdatasync+0x32/0x40
[ 691.490228] do_syscall_64+0x9f/0x540
[ 691.490233] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 691.490235] RIP: 0033:0x7f4b253ad5f0
(...)
[ 691.490239] RSP: 002b:00007fffbb2d6078 EFLAGS: 00000246 ORIG_RAX: 000000000000004b
[ 691.490242] RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f4b253ad5f0
[ 691.490244] RDX: 00007fffbb2d5fe0 RSI: 00007fffbb2d5fe0 RDI: 0000000000000003
[ 691.490245] RBP: 000000000000000d R08: 0000000000000001 R09: 00007fffbb2d608c
[ 691.490247] R10: 00000000000002e8 R11: 0000000000000246 R12: 00000000000001f4
[ 691.490248] R13: 0000000051eb851f R14: 00007fffbb2d6120 R15: 00005635a498bda0
This started happening recently when running some test cases from fstests
like btrfs/004 for example, because support for rename exchange was added
last week to fsstress from fstests.
So fix this by deleting the log context for the source root from the list
if we have logged the new name in the source root.
Reported-by: Su Yue <Damenly_Su@gmx.com>
Fixes: d4682ba03e ("Btrfs: sync log after logging new name")
CC: stable@vger.kernel.org # 4.19+
Tested-by: Su Yue <Damenly_Su@gmx.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We hit a regression while rolling out 5.2 internally where we were
hitting the following panic
kernel BUG at mm/page-writeback.c:2659!
RIP: 0010:clear_page_dirty_for_io+0xe6/0x1f0
Call Trace:
__process_pages_contig+0x25a/0x350
? extent_clear_unlock_delalloc+0x43/0x70
submit_compressed_extents+0x359/0x4d0
normal_work_helper+0x15a/0x330
process_one_work+0x1f5/0x3f0
worker_thread+0x2d/0x3d0
? rescuer_thread+0x340/0x340
kthread+0x111/0x130
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x1f/0x30
This is happening because the page is not locked when doing
clear_page_dirty_for_io. Looking at the core dump it was because our
async_extent had a ram_size of 24576 but our async_chunk range only
spanned 20480, so we had a whole extra page in our ram_size for our
async_extent.
This happened because we try not to compress pages outside of our
i_size, however a cleanup patch changed us to do
actual_end = min_t(u64, i_size_read(inode), end + 1);
which is problematic because i_size_read() can evaluate to different
values in between checking and assigning. So either an expanding
truncate or a fallocate could increase our i_size while we're doing
writeout and actual_end would end up being past the range we have
locked.
I confirmed this was what was happening by installing a debug kernel
that had
actual_end = min_t(u64, i_size_read(inode), end + 1);
if (actual_end > end + 1) {
printk(KERN_ERR "KABOOM\n");
actual_end = end + 1;
}
and installing it onto 500 boxes of the tier that had been seeing the
problem regularly. Last night I got my debug message and no panic,
confirming what I expected.
[ dsterba: the assembly confirms a tiny race window:
mov 0x20(%rsp),%rax
cmp %rax,0x48(%r15) # read
movl $0x0,0x18(%rsp)
mov %rax,%r12
mov %r14,%rax
cmovbe 0x48(%r15),%r12 # eval
Where r15 is inode and 0x48 is offset of i_size.
The original fix was to revert 62b3762271 that would do an
intermediate assignment and this would also avoid the doulble
evaluation but is not future-proof, should the compiler merge the
stores and call i_size_read anyway.
There's a patch adding READ_ONCE to i_size_read but that's not being
applied at the moment and we need to fix the bug. Instead, emulate
READ_ONCE by two barrier()s that's what effectively happens. The
assembly confirms single evaluation:
mov 0x48(%rbp),%rax # read once
mov 0x20(%rsp),%rcx
mov $0x20,%edx
cmp %rax,%rcx
cmovbe %rcx,%rax
mov %rax,(%rsp)
mov %rax,%rcx
mov %r14,%rax
Where 0x48(%rbp) is inode->i_size stored to %eax.
]
Fixes: 62b3762271 ("btrfs: Remove isize local variable in compress_file_range")
CC: stable@vger.kernel.org # v5.1+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ changelog updated ]
Signed-off-by: David Sterba <dsterba@suse.com>
[Background]
Btrfs qgroup uses two types of reserved space for METADATA space,
PERTRANS and PREALLOC.
PERTRANS is metadata space reserved for each transaction started by
btrfs_start_transaction().
While PREALLOC is for delalloc, where we reserve space before joining a
transaction, and finally it will be converted to PERTRANS after the
writeback is done.
[Inconsistency]
However there is inconsistency in how we handle PREALLOC metadata space.
The most obvious one is:
In btrfs_buffered_write():
btrfs_delalloc_release_extents(BTRFS_I(inode), reserve_bytes, true);
We always free qgroup PREALLOC meta space.
While in btrfs_truncate_block():
btrfs_delalloc_release_extents(BTRFS_I(inode), blocksize, (ret != 0));
We only free qgroup PREALLOC meta space when something went wrong.
[The Correct Behavior]
The correct behavior should be the one in btrfs_buffered_write(), we
should always free PREALLOC metadata space.
The reason is, the btrfs_delalloc_* mechanism works by:
- Reserve metadata first, even it's not necessary
In btrfs_delalloc_reserve_metadata()
- Free the unused metadata space
Normally in:
btrfs_delalloc_release_extents()
|- btrfs_inode_rsv_release()
Here we do calculation on whether we should release or not.
E.g. for 64K buffered write, the metadata rsv works like:
/* The first page */
reserve_meta: num_bytes=calc_inode_reservations()
free_meta: num_bytes=0
total: num_bytes=calc_inode_reservations()
/* The first page caused one outstanding extent, thus needs metadata
rsv */
/* The 2nd page */
reserve_meta: num_bytes=calc_inode_reservations()
free_meta: num_bytes=calc_inode_reservations()
total: not changed
/* The 2nd page doesn't cause new outstanding extent, needs no new meta
rsv, so we free what we have reserved */
/* The 3rd~16th pages */
reserve_meta: num_bytes=calc_inode_reservations()
free_meta: num_bytes=calc_inode_reservations()
total: not changed (still space for one outstanding extent)
This means, if btrfs_delalloc_release_extents() determines to free some
space, then those space should be freed NOW.
So for qgroup, we should call btrfs_qgroup_free_meta_prealloc() other
than btrfs_qgroup_convert_reserved_meta().
The good news is:
- The callers are not that hot
The hottest caller is in btrfs_buffered_write(), which is already
fixed by commit 336a8bb8e3 ("btrfs: Fix wrong
btrfs_delalloc_release_extents parameter"). Thus it's not that
easy to cause false EDQUOT.
- The trans commit in advance for qgroup would hide the bug
Since commit f5fef45936 ("btrfs: qgroup: Make qgroup async transaction
commit more aggressive"), when btrfs qgroup metadata free space is slow,
it will try to commit transaction and free the wrongly converted
PERTRANS space, so it's not that easy to hit such bug.
[FIX]
So to fix the problem, remove the @qgroup_free parameter for
btrfs_delalloc_release_extents(), and always pass true to
btrfs_inode_rsv_release().
Reported-by: Filipe Manana <fdmanana@suse.com>
Fixes: 43b18595d6 ("btrfs: qgroup: Use separate meta reservation type for delalloc")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since commit fee187d9d9 ("Btrfs: do not set EXTENT_DIRTY along with
EXTENT_DELALLOC"), we never set EXTENT_DIRTY in inode->io_tree, so we
can simplify and stop trying to clear it.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Further simplifaction of the get/set helpers is possible when the token
is uniquely tied to an extent buffer. A condition and an assignment can
be avoided.
The initializations are moved closer to the first use when the extent
buffer is valid. There's one exception in __push_leaf_left where the
token is reused.
Signed-off-by: David Sterba <dsterba@suse.com>
The file ctree.h serves as a header for everything and has become quite
bloated. Split some helpers that are generic and create a new file that
should be the catch-all for code that's not btrfs-specific.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
Various notifications of type "BUG kmalloc-4096 () : Redzone
overwritten" have been observed recently in various parts of the kernel.
After some time, it has been made a relation with the use of BTRFS
filesystem and with SLUB_DEBUG turned on.
[ 22.809700] BUG kmalloc-4096 (Tainted: G W ): Redzone overwritten
[ 22.810286] INFO: 0xbe1a5921-0xfbfc06cd. First byte 0x0 instead of 0xcc
[ 22.810866] INFO: Allocated in __load_free_space_cache+0x588/0x780 [btrfs] age=22 cpu=0 pid=224
[ 22.811193] __slab_alloc.constprop.26+0x44/0x70
[ 22.811345] kmem_cache_alloc_trace+0xf0/0x2ec
[ 22.811588] __load_free_space_cache+0x588/0x780 [btrfs]
[ 22.811848] load_free_space_cache+0xf4/0x1b0 [btrfs]
[ 22.812090] cache_block_group+0x1d0/0x3d0 [btrfs]
[ 22.812321] find_free_extent+0x680/0x12a4 [btrfs]
[ 22.812549] btrfs_reserve_extent+0xec/0x220 [btrfs]
[ 22.812785] btrfs_alloc_tree_block+0x178/0x5f4 [btrfs]
[ 22.813032] __btrfs_cow_block+0x150/0x5d4 [btrfs]
[ 22.813262] btrfs_cow_block+0x194/0x298 [btrfs]
[ 22.813484] commit_cowonly_roots+0x44/0x294 [btrfs]
[ 22.813718] btrfs_commit_transaction+0x63c/0xc0c [btrfs]
[ 22.813973] close_ctree+0xf8/0x2a4 [btrfs]
[ 22.814107] generic_shutdown_super+0x80/0x110
[ 22.814250] kill_anon_super+0x18/0x30
[ 22.814437] btrfs_kill_super+0x18/0x90 [btrfs]
[ 22.814590] INFO: Freed in proc_cgroup_show+0xc0/0x248 age=41 cpu=0 pid=83
[ 22.814841] proc_cgroup_show+0xc0/0x248
[ 22.814967] proc_single_show+0x54/0x98
[ 22.815086] seq_read+0x278/0x45c
[ 22.815190] __vfs_read+0x28/0x17c
[ 22.815289] vfs_read+0xa8/0x14c
[ 22.815381] ksys_read+0x50/0x94
[ 22.815475] ret_from_syscall+0x0/0x38
Commit 69d2480456 ("btrfs: use copy_page for copying pages instead of
memcpy") changed the way bitmap blocks are copied. But allthough bitmaps
have the size of a page, they were allocated with kzalloc().
Most of the time, kzalloc() allocates aligned blocks of memory, so
copy_page() can be used. But when some debug options like SLAB_DEBUG are
activated, kzalloc() may return unaligned pointer.
On powerpc, memcpy(), copy_page() and other copying functions use
'dcbz' instruction which provides an entire zeroed cacheline to avoid
memory read when the intention is to overwrite a full line. Functions
like memcpy() are writen to care about partial cachelines at the start
and end of the destination, but copy_page() assumes it gets pages. As
pages are naturally cache aligned, copy_page() doesn't care about
partial lines. This means that when copy_page() is called with a
misaligned pointer, a few leading bytes are zeroed.
To fix it, allocate bitmaps through kmem_cache instead of using kzalloc()
The cache pool is created with PAGE_SIZE alignment constraint.
Reported-by: Erhard F. <erhard_f@mailbox.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204371
Fixes: 69d2480456 ("btrfs: use copy_page for copying pages instead of memcpy")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: David Sterba <dsterba@suse.com>
[ rename to btrfs_free_space_bitmap ]
Signed-off-by: David Sterba <dsterba@suse.com>
Correctly handle failure cases when adding an ordered extents in case
of REGULAR or PREALLOC extents. Remove the BUG_ON.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add a comment explaining why we keep the BUG also use the already read
and cached value of extent ram bytes stored in 'ram_bytes'.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The extent range check right after the "out_check" label is redundant,
because the only way it can trigger is if we have an inline extent. In
this case it makes more sense to actually move it in the branch
explictly dealing with inlines extents.
What's more, the nested 'if (nocow)' can never be true because for
inline extents we always do COW and there is no chance 'nocow' can be
true, just remove that check.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There is no point in checking the type of the extent again just to set
the 'type' variable, when this check has already been performed before.
Instead, extend the original if branch with an 'else' clause. This
allows to remove one local variable and make it obvious how the code
flow differs for prealloc/regular extents.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
run_delalloc_nocow contains numerous, somewhat subtle, checks when
figuring out whether a particular extent should be CoW'ed or not. This
patch explicitly states the assumptions those checks verify. As a
result also document 2 of the more subtle checks in check_committed_ref
as well.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Of the 22 (!!!) local variables declared in this function only 9 have
function-wide context. Of the remaining 13, 12 are needed in the main
while loop of the function and 1 is needed in a tiny if branch, only in
case we have prealloc extent. This commit reduces the lifespan of every
variable to its bare minimum. It also renames the 'nolock' boolean to
freespace_inode to clearly indicate its purpose.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_calc_trunc_metadata_size differs from trans_metadata_size in that
it doesn't take into account any splitting at the levels, because
truncate will never split nodes. However truncate _and_ changing will
never split nodes, so rename btrfs_calc_trunc_metadata_size to
btrfs_calc_metadata_size. Also btrfs_calc_trans_metadata_size is purely
for inserting items, so rename this to btrfs_calc_insert_metadata_size.
Making these clearer will help when I start using them differently in
upcoming patches.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We have this weird space flushing loop inside inode.c for evict where
we'll do the normal LIMIT flush, and then commit the transaction and
hope we get our space. This is super janky, and in fact there's really
nothing stopping us from using FLUSH_ALL except that we run delayed
iputs, which means we could deadlock. So introduce a new flush state
for eviction that does the normal priority flushing with all of the
states that are safe for eviction.
The nice side-effect of this is that we'll try harder for evictions.
Previously if (for example generic/269) you had a bunch of other
operations happening on the fs you could race with those reservations
when committing the transaction, and eventually miss getting a
reservation for the evict. With this code we'll have our ticket in
place through the transaction commit, so any pinned bytes will go to our
pending evictions first.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This is prep work for moving all of the block group cache code into its
own file.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ minor comment updates ]
Signed-off-by: David Sterba <dsterba@suse.com>
In insert_inline_extent(), the case that checks compressed_size > 0
and compressed_pages = NULL cannot occur, otherwise a null-pointer
dereference may occur on line 215:
cpage = compressed_pages[i];
To catch this incorrect case, an assertion is added.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's unlikely in-band dedupe is going to land so just remove any
leftovers - dedupe.h header as well as the 'dedupe' parameter to
btrfs_set_extent_delalloc.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It was added in ba8b04c1d4 ("btrfs: extend btrfs_set_extent_delalloc
and its friends to support in-band dedupe and subpage size patchset") as
a preparatory patch for in-band and subapge block size patchsets.
However neither of those are likely to be merged anytime soon and the
code has diverged significantly from the last public post of either
of those patchsets.
It's unlikely either of the patchests are going to use those preparatory
steps so just remove the variables. Since cow_file_range also took
delalloc_end to pass it to extent_clear_unlock_delalloc remove the
parameter from that function as well.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This label is only executed if compress_file_range fails to create an
inline extent. So move its code in the semantically related inline
extent handling branch. No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
compress_file_range returns a void, yet uses a function parameter as a
return value. Make that more idiomatic by simply returning the number
of compressed extents directly. Also track such extents in more aptly
named variables. No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
As btrfs(5) specified:
Note
If nodatacow or nodatasum are enabled, compression is disabled.
If NODATASUM or NODATACOW set, we should not compress the extent.
Normally NODATACOW is detected properly in run_delalloc_range() so
compression won't happen for NODATACOW.
However for NODATASUM we don't have any check, and it can cause
compressed extent without csum pretty easily, just by:
mkfs.btrfs -f $dev
mount $dev $mnt -o nodatasum
touch $mnt/foobar
mount -o remount,datasum,compress $mnt
xfs_io -f -c "pwrite 0 128K" $mnt/foobar
And in fact, we have a bug report about corrupted compressed extent
without proper data checksum so even RAID1 can't recover the corruption.
(https://bugzilla.kernel.org/show_bug.cgi?id=199707)
Running compression without proper checksum could cause more damage when
corruption happens, as compressed data could make the whole extent
unreadable, so there is no need to allow compression for
NODATACSUM.
The fix will refactor the inode compression check into two parts:
- inode_can_compress()
As the hard requirement, checked at btrfs_run_delalloc_range(), so no
compression will happen for NODATASUM inode at all.
- inode_need_compress()
As the soft requirement, checked at btrfs_run_delalloc_range() and
compress_file_range().
Reported-by: James Harvey <jamespharvey20@gmail.com>
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We have code for data and metadata reservations for delalloc. There's
quite a bit of code here, and it's used in a lot of places so I've
separated it out to it's own file. inode.c and file.c are already
pretty large, and this code is complicated enough to live in its own
space.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We have been seeing issues in production where a cleaner script will end
up unlinking a bunch of files that have pending iputs. This means they
will get their final iput's run at btrfs-cleaner time and thus are not
throttled, which impacts the workload.
Since we are unlinking these files we can just drop the delayed iput at
unlink time. We are already holding a reference to the inode so this
will not be the final iput and thus is completely safe to do at this
point. Doing this means we are more likely to be doing the final iput
at unlink time, and thus will get the IO charged to the caller and get
throttled appropriately without affecting the main workload.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Presently btrfs_map_block is used not only to do everything necessary to
map a bio to the underlying allocation profile but it's also used to
identify how much data could be written based on btrfs' stripe logic
without actually submitting anything. This is achieved by passing NULL
for 'bbio_ret' parameter.
This patch refactors all callers that require just the mapping length
by switching them to using btrfs_io_geometry instead of calling
btrfs_map_block with a special NULL value for 'bbio_ret'. No functional
change.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_print_data_csum_error() still assumed checksums to be 32 bit in
size. Make it size agnostic.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently btrfs_csum_data() relied on the crc32c() wrapper around the
crypto framework for calculating the CRCs.
As we have our own crypto_shash structure in the fs_info now, we can
directly call into the crypto framework without going trough the wrapper.
This way we can even remove the btrfs_csum_data() and btrfs_csum_final()
wrappers.
The module dependency on crc32c is preserved via MODULE_SOFTDEP("pre:
crc32c"), which was previously provided by LIBCRC32C config option doing
the same.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There several functions which open code
btrfs_lock_and_flush_ordered_range, just replace them with a call to the
function. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This code was first introduced in 5f39d397df ("Btrfs: Create
extent_buffer interface for large blocksizes") and the function was
named btrfs_unlink_trans. It later got renamed to __btrfs_unlink_inode
and finally commit 16cdcec736 ("btrfs: implement delayed inode items
operation") changed the way inodes are deleted and obviated the need for
those two members.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ replace changelog by Nikolay's version ]
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=lyvo
-----END PGP SIGNATURE-----
Merge tag 'for-5.2-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more fixes for bugs reported by users, fuzzing tools and
regressions:
- fix crashes in relocation:
+ resuming interrupted balance operation does not properly clean
up orphan trees
+ with enabled qgroups, resuming needs to be more careful about
block groups due to limited context when updating qgroups
- fsync and logging fixes found by fuzzing
- incremental send fixes for no-holes and clone
- fix spin lock type used in timer function for zstd"
* tag 'for-5.2-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix race updating log root item during fsync
Btrfs: fix wrong ctime and mtime of a directory after log replay
Btrfs: fix fsync not persisting changed attributes of a directory
btrfs: qgroup: Check bg while resuming relocation to avoid NULL pointer dereference
btrfs: reloc: Also queue orphan reloc tree for cleanup to avoid BUG_ON()
Btrfs: incremental send, fix emission of invalid clone operations
Btrfs: incremental send, fix file corruption when no-holes feature is enabled
btrfs: correct zstd workspace manager lock to use spin_lock_bh()
btrfs: Ensure replaced device doesn't have pending chunk allocation
When replaying a log that contains a new file or directory name that needs
to be added to its parent directory, we end up updating the mtime and the
ctime of the parent directory to the current time after we have set their
values to the correct ones (set at fsync time), efectivelly losing them.
Sample reproducer:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ mkdir /mnt/dir
$ touch /mnt/dir/file
# fsync of the directory is optional, not needed
$ xfs_io -c fsync /mnt/dir
$ xfs_io -c fsync /mnt/dir/file
$ stat -c %Y /mnt/dir
1557856079
<power failure>
$ sleep 3
$ mount /dev/sdb /mnt
$ stat -c %Y /mnt/dir
1557856082
--> should have been 1557856079, the mtime is updated to the current
time when replaying the log
Fix this by not updating the mtime and ctime to the current time at
btrfs_add_link() when we are replaying a log tree.
This could be triggered by my recent fsync fuzz tester for fstests, for
which an fstests patch exists titled "fstests: generic, fsync fuzz tester
with fsstress".
Fixes: e02119d5a7 ("Btrfs: Add a write ahead tree log to optimize synchronous operations")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=Ot0g
-----END PGP SIGNATURE-----
Merge tag 'for-5.2/block-20190507' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"Nothing major in this series, just fixes and improvements all over the
map. This contains:
- Series of fixes for sed-opal (David, Jonas)
- Fixes and performance tweaks for BFQ (via Paolo)
- Set of fixes for bcache (via Coly)
- Set of fixes for md (via Song)
- Enabling multi-page for passthrough requests (Ming)
- Queue release fix series (Ming)
- Device notification improvements (Martin)
- Propagate underlying device rotational status in loop (Holger)
- Removal of mtip32xx trim support, which has been disabled for years
(Christoph)
- Improvement and cleanup of nvme command handling (Christoph)
- Add block SPDX tags (Christoph)
- Cleanup/hardening of bio/bvec iteration (Christoph)
- A few NVMe pull requests (Christoph)
- Removal of CONFIG_LBDAF (Christoph)
- Various little fixes here and there"
* tag 'for-5.2/block-20190507' of git://git.kernel.dk/linux-block: (164 commits)
block: fix mismerge in bvec_advance
block: don't drain in-progress dispatch in blk_cleanup_queue()
blk-mq: move cancel of hctx->run_work into blk_mq_hw_sysfs_release
blk-mq: always free hctx after request queue is freed
blk-mq: split blk_mq_alloc_and_init_hctx into two parts
blk-mq: free hw queue's resource in hctx's release handler
blk-mq: move cancel of requeue_work into blk_mq_release
blk-mq: grab .q_usage_counter when queuing request from plug code path
block: fix function name in comment
nvmet: protect discovery change log event list iteration
nvme: mark nvme_core_init and nvme_core_exit static
nvme: move command size checks to the core
nvme-fabrics: check more command sizes
nvme-pci: check more command sizes
nvme-pci: remove an unneeded variable initialization
nvme-pci: unquiesce admin queue on shutdown
nvme-pci: shutdown on timeout during deletion
nvme-pci: fix psdt field for single segment sgls
nvme-multipath: don't print ANA group state by default
nvme-multipath: split bios with the ns_head bio_set before submitting
...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE8rQSAMVO+zA4DBdWxWXV+ddtWDsFAlzQM7MACgkQxWXV+ddt
WDvrVw/+K0AElSuEfDFWd9HBqRAPlGaEP71xCGGle1tkzuY0DJVIBRZ72q8UR0YP
7yke7DU0oqXekGype83eTJUjDSLoOXrlVoQ+VqBdFteDk0W4BCG6Nw+N+wYBF7An
gXRXlGFaYzb2CqqjG92FbtkfxBzISR0XBCQBUN9CBqHNDu1EUQSbnTBkmTMN8MYh
PCoo37S6e5fR36uB/rOKbGNBJjsZEEg/2G6DprP52+eiQWV2h0avEUJrvv6xC4so
97QNgUNuuiUmyurqcYHdlaflZwIhuf5nQeNeu/UvMZmmRnBHPhSP7YPM7f7FftwA
y0d0p+AiEAO0he8nGFb5C6Avs4vuv1u65o1NbF5fqnmAyt+KXWem3LeG6etsXgU8
+eITgprJD3sNBMDLbLoA+wlhTps+w9tukVF5Zp2a8KgQLMMEyAYqUDWmSHvnO2Me
RCNPZLzeGXETgKun0WuMtl/CX2iBDnc0Kq5O6ks2ORl2TH6bg5lgEIwr6HP/Ewoy
w8twsmCOltrxiIptqyQHYD+kvNwqMVV9LSOQ8+EjbYd6BHsfjHjKObOBkhmJ7iqz
4MAIcZU++F9DLRv92H1kUYVNhAMCdXkEIWyxhZPwN1lUi5k9AhknY3FbheNc7ldl
LNPIgRxamWCq9oBmzfOcJ3eFOBtNN02fgA1GTXGd1/AgAilEep8=
=fEkD
-----END PGP SIGNATURE-----
Merge tag 'for-5.2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs updates from David Sterba:
"This time the majority of changes are cleanups, though there's still a
number of changes of user interest.
User visible changes:
- better read time and write checks to catch errors early and before
writing data to disk (to catch potential memory corruption on data
that get checksummed)
- qgroups + metadata relocation: last speed up patch int the series
to address the slowness, there should be no overhead comparing
balance with and without qgroups
- FIEMAP ioctl does not start a transaction unnecessarily, this can
result in a speed up and less blocking due to IO
- LOGICAL_INO (v1, v2) does not start transaction unnecessarily, this
can speed up the mentioned ioctl and scrub as well
- fsync on files with many (but not too many) hardlinks is faster,
finer decision if the links should be fsynced individually or
completely
- send tries harder to find ranges to clone
- trim/discard will skip unallocated chunks that haven't been touched
since the last mount
Fixes:
- send flushes delayed allocation before start, otherwise it could
miss some changes in case of a very recent rw->ro switch of a
subvolume
- fix fallocate with qgroups that could lead to space accounting
underflow, reported as a warning
- trim/discard ioctl honours the requested range
- starting send and dedupe on a subvolume at the same time will let
only one of them succeed, this is to prevent changes that send
could miss due to dedupe; both operations are restartable
Core changes:
- more tree-checker validations, errors reported by fuzzing tools:
- device item
- inode item
- block group profiles
- tracepoints for extent buffer locking
- async cow preallocates memory to avoid errors happening too deep in
the call chain
- metadata reservations for delalloc reworked to better adapt in
many-writers/low-space scenarios
- improved space flushing logic for intense DIO vs buffered workloads
- lots of cleanups
- removed unused struct members
- redundant argument removal
- properties and xattrs
- extent buffer locking
- selftests
- use common file type conversions
- many-argument functions reduction"
* tag 'for-5.2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (227 commits)
btrfs: Use kvmalloc for allocating compressed path context
btrfs: Factor out common extent locking code in submit_compressed_extents
btrfs: Set io_tree only once in submit_compressed_extents
btrfs: Replace clear_extent_bit with unlock_extent
btrfs: Make compress_file_range take only struct async_chunk
btrfs: Remove fs_info from struct async_chunk
btrfs: Rename async_cow to async_chunk
btrfs: Preallocate chunks in cow_file_range_async
btrfs: reserve delalloc metadata differently
btrfs: track DIO bytes in flight
btrfs: merge calls of btrfs_setxattr and btrfs_setxattr_trans in btrfs_set_prop
btrfs: delete unused function btrfs_set_prop_trans
btrfs: start transaction in xattr_handler_set_prop
btrfs: drop local copy of inode i_mode
btrfs: drop old_fsflags in btrfs_ioctl_setflags
btrfs: modify local copy of btrfs_inode flags
btrfs: drop useless inode i_flags copy and restore
btrfs: start transaction in btrfs_ioctl_setflags()
btrfs: export btrfs_set_prop
btrfs: refactor btrfs_set_props to validate externally
...
Pull vfs inode freeing updates from Al Viro:
"Introduction of separate method for RCU-delayed part of
->destroy_inode() (if any).
Pretty much as posted, except that destroy_inode() stashes
->free_inode into the victim (anon-unioned with ->i_fops) before
scheduling i_callback() and the last two patches (sockfs conversion
and folding struct socket_wq into struct socket) are excluded - that
pair should go through netdev once davem reopens his tree"
* 'work.icache' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (58 commits)
orangefs: make use of ->free_inode()
shmem: make use of ->free_inode()
hugetlb: make use of ->free_inode()
overlayfs: make use of ->free_inode()
jfs: switch to ->free_inode()
fuse: switch to ->free_inode()
ext4: make use of ->free_inode()
ecryptfs: make use of ->free_inode()
ceph: use ->free_inode()
btrfs: use ->free_inode()
afs: switch to use of ->free_inode()
dax: make use of ->free_inode()
ntfs: switch to ->free_inode()
securityfs: switch to ->free_inode()
apparmor: switch to ->free_inode()
rpcpipe: switch to ->free_inode()
bpf: switch to ->free_inode()
mqueue: switch to ->free_inode()
ufs: switch to ->free_inode()
coda: switch to ->free_inode()
...
Recent refactoring of cow_file_range_async means it's now possible to
request a rather large physically contiguous memory via kmalloc. The
size is dependent on the number of 512k chunks that the compressed range
consists of. David reported multiple OOM messages on such large
allocations. Fix it by switching to using kvmalloc.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Irrespective of whether the compress code fell back to uncompressed or
a compressed extent has to be submitted, the extent range is always
locked. So factor out the common lock_extent call at the beginning of
the loop. No functional changes just removes one duplicate lock_extent
call.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The inode never changes so it's sufficient to dereference it and get
the iotree only once, before the execution of the main loop. No
functional changes, only the size of the function is decreased:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-44 (-44)
Function old new delta
submit_compressed_extents 1240 1196 -44
Total: Before=88476, After=88432, chg -0.05%
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All context this function needs is held within struct async_chunk.
Currently we not only pass the struct but also every individual member.
This is redundant, simplify it by only passing struct async_chunk and
leaving it to compress_file_range to extract the values it requires.
No functional changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The associated btrfs_work already contains a reference to the fs_info so
use that instead of passing it via async_chunk. No functional changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that we have an explicit async_chunk struct rename references to
variables of this type to async_chunk. No functional changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This commit changes the implementation of cow_file_range_async in order
to get rid of the BUG_ON in the middle of the loop. Additionally it
reworks the inner loop in the hopes of making it more understandable.
The idea is to make async_cow be a top-level structured, shared amongst
all chunks being sent for compression. This allows to perform one memory
allocation at the beginning and gracefully fail the IO if there isn't
enough memory. Now, each chunk is going to be described by an
async_chunk struct. It's the responsibility of the final chunk
to actually free the memory.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The 'extent_type' variable does seem to be reliably initialized, but
it's _very_ non-obvious, since there's a "goto next" case that jumps
over the normal initialization. That will then always trigger the
"start >= extent_end" test, which will end up never falling through to
the use of that variable.
But the code is certainly not obvious, and the compiler warning looks
reasonable. Make 'extent_type' an int, and initialize it to an invalid
negative value, which seems to be the common pattern in other places.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We only have two callers that need the integer loop iterator, and they
can easily maintain it themselves.
Suggested-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Coly Li <colyli@suse.de>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 41bd606769 ("Btrfs: fix fsync of files with multiple hard links
in new directories") introduced a path that makes fsync fallback to a full
transaction commit in order to avoid losing hard links and new ancestors
of the fsynced inode. That path is triggered only when the inode has more
than one hard link and either has a new hard link created in the current
transaction or the inode was evicted and reloaded in the current
transaction.
That path ends up getting triggered very often (hundreds of times) during
the course of pgbench benchmarks, resulting in performance drops of about
20%.
This change restores the performance by not triggering the full transaction
commit in those cases, and instead iterate the fs/subvolume tree in search
of all possible new ancestors, for all hard links, to log them.
Reported-by: Zhao Yuhu <zyuhu@suse.com>
Tested-by: James Wang <jnwang@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Similar to btrfs_inc_extent_ref(), use btrfs_ref to replace the long
parameter list and the confusing @owner parameter.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Use the new btrfs_ref structure and replace parameter list to clean up
the usage of owner and level to distinguish the extent types.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
None of the implementers of the submit_bio_hook use the bio_offset
parameter, simply remove it. No functional changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Buffered writeback always calls btrfs_csum_one_bio with the last 2
arguments being 0 irrespective of what the bio_offset has been passed to
btrfs_submit_bio_start. Make this apparent by explicitly passing 0 for
bio_offset when calling btrfs_wq_submit_bio from btrfs_submit_bio_hook.
This will allow for further simplifications down the line. No functional
changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The only possible 'private_data' that is passed to this function is
actually an inode. Make that explicit by changing the signature of the
call back. No functional changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
When accessing a file on a crafted image, btrfs can crash in block layer:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
PGD 136501067 P4D 136501067 PUD 124519067 PMD 0
CPU: 3 PID: 0 Comm: swapper/3 Not tainted 5.0.0-rc8-default #252
RIP: 0010:end_bio_extent_readpage+0x144/0x700
Call Trace:
<IRQ>
blk_update_request+0x8f/0x350
blk_mq_end_request+0x1a/0x120
blk_done_softirq+0x99/0xc0
__do_softirq+0xc7/0x467
irq_exit+0xd1/0xe0
call_function_single_interrupt+0xf/0x20
</IRQ>
RIP: 0010:default_idle+0x1e/0x170
[CAUSE]
The crafted image has a tricky corruption, the INODE_ITEM has a
different type against its parent dir:
item 20 key (268 INODE_ITEM 0) itemoff 2808 itemsize 160
generation 13 transid 13 size 1048576 nbytes 1048576
block group 0 mode 121644 links 1 uid 0 gid 0 rdev 0
sequence 9 flags 0x0(none)
This mode number 0120000 means it's a symlink.
But the dir item think it's still a regular file:
item 8 key (264 DIR_INDEX 5) itemoff 3707 itemsize 32
location key (268 INODE_ITEM 0) type FILE
transid 13 data_len 0 name_len 2
name: f4
item 40 key (264 DIR_ITEM 51821248) itemoff 1573 itemsize 32
location key (268 INODE_ITEM 0) type FILE
transid 13 data_len 0 name_len 2
name: f4
For symlink, we don't set BTRFS_I(inode)->io_tree.ops and leave it
empty, as symlink is only designed to have inlined extent, all handled
by tree block read. Thus no need to trigger btrfs_submit_bio_hook() for
inline file extent.
However end_bio_extent_readpage() expects tree->ops populated, as it's
reading regular data extent. This causes NULL pointer dereference.
[FIX]
This patch fixes the problem in two ways:
- Verify inode mode against its dir item when looking up inode
So in btrfs_lookup_dentry() if we find inode mode mismatch with dir
item, we error out so that corrupted inode will not be accessed.
- Verify inode mode when getting extent mapping
Only regular file should have regular or preallocated extent.
If we found regular/preallocated file extent for symlink or
the rest, we error out before submitting the read bio.
With this fix that crafted image can be rejected gracefully:
BTRFS critical (device loop0): inode mode mismatch with dir: inode mode=0121644 btrfs type=7 dir type=1
Reported-by: Yoon Jungyeon <jungyeon@gatech.edu>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202763
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Deduplicate the btrfs file type conversion implementation - file systems
that use the same file types as defined by POSIX do not need to define
their own versions and can use the common helper functions decared in
fs_types.h and implemented in fs_types.c
Common implementation can be found via commit:
bbe7449e25 "fs: common implementation of file type"
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
BUG_ON(1) leads to bogus warnings from clang when
CONFIG_PROFILE_ANNOTATED_BRANCHES is set:
fs/btrfs/volumes.c:5041:3: error: variable 'max_chunk_size' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
BUG_ON(1);
^~~~~~~~~
include/asm-generic/bug.h:61:36: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^~~~~~~~~~~~~~~~~~~
include/linux/compiler.h:48:23: note: expanded from macro 'unlikely'
# define unlikely(x) (__branch_check__(x, 0, __builtin_constant_p(x)))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
fs/btrfs/volumes.c:5046:9: note: uninitialized use occurs here
max_chunk_size);
^~~~~~~~~~~~~~
include/linux/kernel.h:860:36: note: expanded from macro 'min'
#define min(x, y) __careful_cmp(x, y, <)
^
include/linux/kernel.h:853:17: note: expanded from macro '__careful_cmp'
__cmp_once(x, y, __UNIQUE_ID(__x), __UNIQUE_ID(__y), op))
^
include/linux/kernel.h:847:25: note: expanded from macro '__cmp_once'
typeof(y) unique_y = (y); \
^
fs/btrfs/volumes.c:5041:3: note: remove the 'if' if its condition is always true
BUG_ON(1);
^
include/asm-generic/bug.h:61:32: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^
fs/btrfs/volumes.c:4993:20: note: initialize the variable 'max_chunk_size' to silence this warning
u64 max_chunk_size;
^
= 0
Change it to BUG() so clang can see that this code path can never
continue.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Sterba <dsterba@suse.com>
Btrfs has the following different extent_io_trees used:
- fs_info::free_extents[2]
- btrfs_inode::io_tree - for both normal inodes and the btree inode
- btrfs_inode::io_failure_tree
- btrfs_transaction::dirty_pages
- btrfs_root::dirty_log_pages
If we want to trace changes in those trees, it will be pretty hard to
distinguish them.
Instead of using hard-to-read pointer address, this patch will introduce
a new member extent_io_tree::owner to track the owner.
This modification needs all the callers of extent_io_tree_init() to
accept a new parameter @owner.
This patch provides the basis for later trace events.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This patch is split from the following one "btrfs: Introduce
extent_io_tree::owner to distinguish different io_trees" from Qu, so the
different changes are not mixed together.
Signed-off-by: David Sterba <dsterba@suse.com>
This patch will add a new member fs_info to extent_io_tree.
This provides the basis for later trace events to distinguish the output
between different btrfs filesystems. While this increases the size of
the structure, we want to know the source of the trace events and
passing the fs_info as an argument to all contexts is not possible.
The selftests are now allowed to set it to NULL as they don't use the
tracepoints.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
inode->i_op is initialized multiple times. Perform it once. This was
left by 4779cc0424 ("Btrfs: get rid of btrfs_symlink_aops").
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=VBaU
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
We could generate a lot of delayed refs in evict but never have any left
over space from our block rsv to make up for that fact. So reserve some
extra space and give it to the transaction so it can be used to refill
the delayed refs rsv every loop through the truncate path.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The throttle path doesn't take cleaner_delayed_iput_mutex, which means
we could think we're done flushing iputs in the data space reservation
path when we could have a throttler doing an iput. There's no real
reason to serialize the delayed iput flushing, so instead of taking the
cleaner_delayed_iput_mutex whenever we flush the delayed iputs just
replace it with an atomic counter and a waitqueue. This removes the
short (or long depending on how big the inode is) window where we think
there are no more pending iputs when there really are some.
The waiting is killable as it could be indirectly called from user
operations like fallocate or zero-range. Such call sites should handle
the error but otherwise it's not necessary. Eg. flush_space just needs
to attempt to make space by waiting on iputs.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
[ add killable comment and changelog parts ]
Signed-off-by: David Sterba <dsterba@suse.com>
In order to avoid duplicating init code for em there is an additional
label, not_found_em, which is used to only set ->block_start. The only
case when it will be used is if the extent we are adding overlaps with
an existing extent. Make that case more obvious by:
1. Adding a comment hinting at what's going on
2. Assigning EXTENT_MAP_HOLE and directly going to insert.
No functional changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Core btree functions in btrfs generally return 0 when an item is found,
1 in case the sought item cannot be found and <0 when an error happens.
Consolidate the checks for those conditions in one 'if () {} else if ()
{}' construct rather than 2 separate 'if () {}' statements. This
emphasizes that the handling code pertains to a single function. No
functional changes.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
found_type really holds the type of extent and is guaranteed to to have
a value between [0, 2]. The only time it can contain anything different
is if btrfs_lookup_file_extent returned a positive value and the
previous item is different than an extent. Avoid this situation by
simply checking found_key.type rather than assigning the item type to
found_type intermittently. Also make the variable an u8 to reduce stack
usage. No functional changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add a comment explaining when ->inode could be NULL and why we always
perform the ->async_delalloc_pages modification.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It can never trigger since before calling alloc_delalloc_work we have
called igrab in start_delalloc_inodes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
ihold is supposed to be used when the caller already has a reference to
the inode. In the case of cow_file_range_async this invariants holds,
since the 3 call chains leading to this function all take a reference:
btrfs_writepage <--- does igrab
extent_write_full_page
__extent_writepage
writepage_delalloc
btrfs_run_delalloc_range
cow_file_range_async
extent_write_cache_pages <--- does igrab
__extent_writepage (same callchain as above)
and
submit_compressed_extents <-- already called from async CoW submit path,
which would have done ihold.
extent_write_locked_range
__extent_writepage
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
It's used only once so just inline the call to i_size_read. The
semantics regarding the inode size are not changed, the pages in the
range are locked and i_size cannot change between the time it was set
and used.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We already pass the async_cow struct that holds a reference to the
inode. Exploit this fact and remove the extra inode argument. No
functional changes.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
hole_len is only used if the hole falls within the requested range. Make
that explicitly clear by only assigning in the corresponding branch.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Make btrfs_get_extent_fiemap a bit more friendly. First step is to
rename the closely related, yet arbitrary named
range_start/found_end/found variables. They define the delalloc range
that is found in case a real extent wasn't found. Subsequently remove
an unnecessary check for hole_em since it's guaranteed to be set i.e the
check is always true. Top it off by giving all comments a refresh.
No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ reformatted a few more comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
This function is a simple wrapper over btrfs_get_extent that returns
either:
a) A real extent in the passed range or
b) Adjusted extent based on whether delalloc bytes are found backing up
a hole.
To support these semantics it doesn't need the page/pg_offset/create
arguments which are passed to btrfs_get_extent in case an extent is to
be created. So simplify the function by removing the unused arguments.
No functional changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since this function is no longer a callback there is no need to have
its first argument obfuscated with a void *. Change it directly to a
pointer to an inode. No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This patch introduces one extra iterator variable to bio_for_each_segment_all(),
then we can allow bio_for_each_segment_all() to iterate over multi-page bvec.
Given it is just one mechannical & simple change on all bio_for_each_segment_all()
users, this patch does tree-wide change in one single patch, so that we can
avoid to use a temporary helper for this conversion.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The cleaner thread usually takes care of delayed iputs, with the
exception of the btrfs_end_transaction_throttle path. Delaying iputs
means we are potentially delaying the eviction of an inode and it's
respective space. The cleaner thread only gets woken up every 30
seconds, or when we require space. If there are a lot of inodes that
need to be deleted we could induce a serious amount of latency while we
wait for these inodes to be evicted. So instead wakeup the cleaner if
it's not already awake to process any new delayed iputs we add to the
list. If we suddenly need space we will less likely be backed up
behind a bunch of inodes that are waiting to be deleted, and we could
possibly free space before we need to get into the flushing logic which
will save us some latency.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This reverts commit e73e81b6d0.
This patch causes a few problems:
- adds latency to btrfs_finish_ordered_io
- as btrfs_finish_ordered_io is used for free space cache, generating
more work from btrfs_btree_balance_dirty_nodelay could end up in the
same workque, effectively deadlocking
12260 kworker/u96:16+btrfs-freespace-write D
[<0>] balance_dirty_pages+0x6e6/0x7ad
[<0>] balance_dirty_pages_ratelimited+0x6bb/0xa90
[<0>] btrfs_finish_ordered_io+0x3da/0x770
[<0>] normal_work_helper+0x1c5/0x5a0
[<0>] process_one_work+0x1ee/0x5a0
[<0>] worker_thread+0x46/0x3d0
[<0>] kthread+0xf5/0x130
[<0>] ret_from_fork+0x24/0x30
[<0>] 0xffffffffffffffff
Transaction commit will wait on the freespace cache:
838 btrfs-transacti D
[<0>] btrfs_start_ordered_extent+0x154/0x1e0
[<0>] btrfs_wait_ordered_range+0xbd/0x110
[<0>] __btrfs_wait_cache_io+0x49/0x1a0
[<0>] btrfs_write_dirty_block_groups+0x10b/0x3b0
[<0>] commit_cowonly_roots+0x215/0x2b0
[<0>] btrfs_commit_transaction+0x37e/0x910
[<0>] transaction_kthread+0x14d/0x180
[<0>] kthread+0xf5/0x130
[<0>] ret_from_fork+0x24/0x30
[<0>] 0xffffffffffffffff
And then writepages ends up waiting on transaction commit:
9520 kworker/u96:13+flush-btrfs-1 D
[<0>] wait_current_trans+0xac/0xe0
[<0>] start_transaction+0x21b/0x4b0
[<0>] cow_file_range_inline+0x10b/0x6b0
[<0>] cow_file_range.isra.69+0x329/0x4a0
[<0>] run_delalloc_range+0x105/0x3c0
[<0>] writepage_delalloc+0x119/0x180
[<0>] __extent_writepage+0x10c/0x390
[<0>] extent_write_cache_pages+0x26f/0x3d0
[<0>] extent_writepages+0x4f/0x80
[<0>] do_writepages+0x17/0x60
[<0>] __writeback_single_inode+0x59/0x690
[<0>] writeback_sb_inodes+0x291/0x4e0
[<0>] __writeback_inodes_wb+0x87/0xb0
[<0>] wb_writeback+0x3bb/0x500
[<0>] wb_workfn+0x40d/0x610
[<0>] process_one_work+0x1ee/0x5a0
[<0>] worker_thread+0x1e0/0x3d0
[<0>] kthread+0xf5/0x130
[<0>] ret_from_fork+0x24/0x30
[<0>] 0xffffffffffffffff
Eventually, we have every process in the system waiting on
balance_dirty_pages(), and nobody is able to make progress on page
writeback.
The original patch tried to fix an OOM condition, that happened on 4.4 but no
success reproducing that on later kernels (4.19 and 4.20). This is more likely
a problem in OOM itself.
Link: https://lore.kernel.org/linux-btrfs/20180528054821.9092-1-ethanlien@synology.com/
Reported-by: Chris Mason <clm@fb.com>
CC: stable@vger.kernel.org # 4.18+
CC: ethanlien <ethanlien@synology.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The typos accumulate over time so once in a while time they get fixed in
a large patch.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In the error handling block, err holds the return value of either
btrfs_del_root_ref() or btrfs_del_inode_ref() but it hasn't been checked
since it's introduction with commit fe66a05a06 (Btrfs: improve error
handling for btrfs_insert_dir_item callers) in 2012.
If the error handling in the error handling fails, there's not much left
to do and the abort either happened earlier in the callees or is
necessary here.
So if one of btrfs_del_root_ref() or btrfs_del_inode_ref() failed, abort
the transaction, but still return the original code of the failure
stored in 'ret' as this will be reported to the user.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We have a bunch of magic to make sure we're throttling delayed refs when
truncating a file. Now that we have a delayed refs rsv and a mechanism
for refilling that reserve simply use that instead of all of this magic.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now with the delayed_refs_rsv we can now know exactly how much pending
delayed refs space we need. This means we can drastically simplify
btrfs_check_space_for_delayed_refs by simply checking how much space we
have reserved for the global rsv (which acts as a spill over buffer) and
the delayed refs rsv. If our total size is beyond that amount then we
know it's time to commit the transaction and stop any more delayed refs
from being generated.
With the introduction of dealyed_refs_rsv infrastructure, namely
btrfs_update_delayed_refs_rsv we now know exactly how much pending
delayed refs space is required.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When using a 'var & (PAGE_SIZE - 1)' construct one is checking for a page
alignment and thus should use the PAGE_ALIGNED() macro instead of
open-coding it.
Convert all open-coded occurrences of PAGE_ALIGNED().
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Constructs like 'var & (PAGE_SIZE - 1)' or 'var & ~PAGE_MASK' can denote an
offset into a page.
So replace them by the offset_in_page() macro instead of open-coding it if
they're not used as an alignment check.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Running btrfs/124 in a loop hung up on me sporadically with the
following call trace:
btrfs D 0 5760 5324 0x00000000
Call Trace:
? __schedule+0x243/0x800
schedule+0x33/0x90
btrfs_start_ordered_extent+0x10c/0x1b0 [btrfs]
? wait_woken+0xa0/0xa0
btrfs_wait_ordered_range+0xbb/0x100 [btrfs]
btrfs_relocate_block_group+0x1ff/0x230 [btrfs]
btrfs_relocate_chunk+0x49/0x100 [btrfs]
btrfs_balance+0xbeb/0x1740 [btrfs]
btrfs_ioctl_balance+0x2ee/0x380 [btrfs]
btrfs_ioctl+0x1691/0x3110 [btrfs]
? lockdep_hardirqs_on+0xed/0x180
? __handle_mm_fault+0x8e7/0xfb0
? _raw_spin_unlock+0x24/0x30
? __handle_mm_fault+0x8e7/0xfb0
? do_vfs_ioctl+0xa5/0x6e0
? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
do_vfs_ioctl+0xa5/0x6e0
? entry_SYSCALL_64_after_hwframe+0x3e/0xbe
ksys_ioctl+0x3a/0x70
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x60/0x1b0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
This happens because during page writeback it's valid for
writepage_delalloc to instantiate a delalloc range which doesn't belong
to the page currently being written back.
The reason this case is valid is due to find_lock_delalloc_range
returning any available range after the passed delalloc_start and
ignoring whether the page under writeback is within that range.
In turn ordered extents (OE) are always created for the returned range
from find_lock_delalloc_range. If, however, a failure occurs while OE
are being created then the clean up code in btrfs_cleanup_ordered_extents
will be called.
Unfortunately the code in btrfs_cleanup_ordered_extents doesn't consider
the case of such 'foreign' range being processed and instead it always
assumes that the range OE are created for belongs to the page. This
leads to the first page of such foregin range to not be cleaned up since
it's deliberately missed and skipped by the current cleaning up code.
Fix this by correctly checking whether the current page belongs to the
range being instantiated and if so adjsut the range parameters passed
for cleaning up. If it doesn't, then just clean the whole OE range
directly.
Fixes: 524272607e ("btrfs: Handle delalloc error correctly to avoid ordered extent hang")
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The test case btrfs/001 with inode_cache mount option will encounter the
following warning:
WARNING: CPU: 1 PID: 23700 at fs/btrfs/inode.c:956 cow_file_range.isra.19+0x32b/0x430 [btrfs]
CPU: 1 PID: 23700 Comm: btrfs Kdump: loaded Tainted: G W O 4.20.0-rc4-custom+ #30
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:cow_file_range.isra.19+0x32b/0x430 [btrfs]
Call Trace:
? free_extent_buffer+0x46/0x90 [btrfs]
run_delalloc_nocow+0x455/0x900 [btrfs]
btrfs_run_delalloc_range+0x1a7/0x360 [btrfs]
writepage_delalloc+0xf9/0x150 [btrfs]
__extent_writepage+0x125/0x3e0 [btrfs]
extent_write_cache_pages+0x1b6/0x3e0 [btrfs]
? __wake_up_common_lock+0x63/0xc0
extent_writepages+0x50/0x80 [btrfs]
do_writepages+0x41/0xd0
? __filemap_fdatawrite_range+0x9e/0xf0
__filemap_fdatawrite_range+0xbe/0xf0
btrfs_fdatawrite_range+0x1b/0x50 [btrfs]
__btrfs_write_out_cache+0x42c/0x480 [btrfs]
btrfs_write_out_ino_cache+0x84/0xd0 [btrfs]
btrfs_save_ino_cache+0x551/0x660 [btrfs]
commit_fs_roots+0xc5/0x190 [btrfs]
btrfs_commit_transaction+0x2bf/0x8d0 [btrfs]
btrfs_mksubvol+0x48d/0x4d0 [btrfs]
btrfs_ioctl_snap_create_transid+0x170/0x180 [btrfs]
btrfs_ioctl_snap_create_v2+0x124/0x180 [btrfs]
btrfs_ioctl+0x123f/0x3030 [btrfs]
The file extent generation of the free space inode is equal to the last
snapshot of the file root, so the inode will be passed to cow_file_rage.
But the inode was created and its extents were preallocated in
btrfs_save_ino_cache, there are no cow copies on disk.
The preallocated extent is not yet in the extent tree, and
btrfs_cross_ref_exist will ignore the -ENOENT returned by
check_committed_ref, so we can directly write the inode to the disk.
Fixes: 78d4295b1e ("btrfs: lift some btrfs_cross_ref_exist checks in nocow path")
CC: stable@vger.kernel.org # 4.18+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The log tree has a long standing problem that when a file is fsync'ed we
only check for new ancestors, created in the current transaction, by
following only the hard link for which the fsync was issued. We follow the
ancestors using the VFS' dget_parent() API. This means that if we create a
new link for a file in a directory that is new (or in an any other new
ancestor directory) and then fsync the file using an old hard link, we end
up not logging the new ancestor, and on log replay that new hard link and
ancestor do not exist. In some cases, involving renames, the file will not
exist at all.
Example:
mkfs.btrfs -f /dev/sdb
mount /dev/sdb /mnt
mkdir /mnt/A
touch /mnt/foo
ln /mnt/foo /mnt/A/bar
xfs_io -c fsync /mnt/foo
<power failure>
In this example after log replay only the hard link named 'foo' exists
and directory A does not exist, which is unexpected. In other major linux
filesystems, such as ext4, xfs and f2fs for example, both hard links exist
and so does directory A after mounting again the filesystem.
Checking if any new ancestors are new and need to be logged was added in
2009 by commit 12fcfd22fe ("Btrfs: tree logging unlink/rename fixes"),
however only for the ancestors of the hard link (dentry) for which the
fsync was issued, instead of checking for all ancestors for all of the
inode's hard links.
So fix this by tracking the id of the last transaction where a hard link
was created for an inode and then on fsync fallback to a full transaction
commit when an inode has more than one hard link and at least one new hard
link was created in the current transaction. This is the simplest solution
since this is not a common use case (adding frequently hard links for
which there's an ancestor created in the current transaction and then
fsync the file). In case it ever becomes a common use case, a solution
that consists of iterating the fs/subvol btree for each hard link and
check if any ancestor is new, could be implemented.
This solves many unexpected scenarios reported by Jayashree Mohan and
Vijay Chidambaram, and for which there is a new test case for fstests
under review.
Fixes: 12fcfd22fe ("Btrfs: tree logging unlink/rename fixes")
CC: stable@vger.kernel.org # 4.4+
Reported-by: Vijay Chidambaram <vvijay03@gmail.com>
Reported-by: Jayashree Mohan <jayashree2912@gmail.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function really checks whether adding more data to the bio will
straddle a stripe/chunk. So first let's give it a more appropraite name
- btrfs_bio_fits_in_stripe. Secondly, the offset parameter was never
used to just remove it. Thirdly, pages are submitted to either btree or
data inodes so it's guaranteed that tree->ops is set so replace the
check with an ASSERT. Finally, document the parameters of the function.
No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
For data inodes this hook does nothing but to return -EAGAIN which is
used to signal to the endio routines that this bio belongs to a data
inode. If this is the case the actual retrying is handled by
bio_readpage_error. Alternatively, if this bio belongs to the btree
inode then btree_io_failed_hook just does some cleanup and doesn't retry
anything.
This patch simplifies the code flow by eliminating
readpage_io_failed_hook and instead open-coding btree_io_failed_hook in
end_bio_extent_readpage. Also eliminate some needless checks since IO is
always performed on either data inode or btree inode, both of which are
guaranteed to have their extent_io_tree::ops set.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The end_io callback implemented as btrfs_io_bio_endio_readpage only
calls kfree. Also the callback is set only in case the csum buffer is
allocated and not pointing to the inline buffer. We can use that
information to drop the indirection and call a helper that will free the
csums only in the right case.
This shrinks struct btrfs_io_bio by 8 bytes.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
The async_cow::root is used to propagate fs_info to async_cow_submit.
We can't use inode to reach it because it could become NULL after
write without compression in async_cow_start.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
There's one caller and its code is simple, we can open code it in
run_one_async_done. The errors are passed through bio.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
Up to commit 32955c5422 ("btrfs: switch to discard_new_inode()") the
drop_on_err variable in btrfs_mkdir() was used to check whether the
inode had to be dropped via iput().
After commit 32955c5422 ("btrfs: switch to discard_new_inode()")
discard_new_inode() is called when err is set and inode is non NULL.
Therefore drop_on_err is not used anymore and thus causes a warning when
building with -Wunused-but-set-variable.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
Snapshot is expected to be fast. But if there are writers steadily
creating dirty pages in our subvolume, the snapshot may take a very long
time to complete. To fix the problem, we use tagged writepage for
snapshot flusher as we do in the generic write_cache_pages(), so we can
omit pages dirtied after the snapshot command.
This does not change the semantics regarding which data get to the
snapshot, if there are pages being dirtied during the snapshotting
operation. There's a sync called before snapshot is taken in old/new
case, any IO in flight just after that may be in the snapshot but this
depends on other system effects that might still sync the IO.
We do a simple snapshot speed test on a Intel D-1531 box:
fio --ioengine=libaio --iodepth=32 --bs=4k --rw=write --size=64G
--direct=0 --thread=1 --numjobs=1 --time_based --runtime=120
--filename=/mnt/sub/testfile --name=job1 --group_reporting & sleep 5;
time btrfs sub snap -r /mnt/sub /mnt/snap; killall fio
original: 1m58sec
patched: 6.54sec
This is the best case for this patch since for a sequential write case,
we omit nearly all pages dirtied after the snapshot command.
For a multi writers, random write test:
fio --ioengine=libaio --iodepth=32 --bs=4k --rw=randwrite --size=64G
--direct=0 --thread=1 --numjobs=4 --time_based --runtime=120
--filename=/mnt/sub/testfile --name=job1 --group_reporting & sleep 5;
time btrfs sub snap -r /mnt/sub /mnt/snap; killall fio
original: 15.83sec
patched: 10.35sec
The improvement is smaller compared to the sequential write case,
since we omit only half of the pages dirtied after snapshot command.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Ethan Lien <ethanlien@synology.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This parameter was never used, yet was part of the interface of the
function ever since its introduction as extent_io_ops::writepage_end_io_hook
in e6dcd2dc9c ("Btrfs: New data=ordered implementation"). Now that
NULL is passed everywhere as a value for this parameter let's remove it
for good. No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Btrfs has not allowed swap files since commit 35054394c4 ("Btrfs: stop
providing a bmap operation to avoid swapfile corruptions"). However, now
that the proper restrictions are in place, Btrfs can support swap files
through the swap file a_ops, similar to iomap in commit 67482129cd
("iomap: add a swapfile activation function").
For Btrfs, activation needs to make sure that the file can be used as a
swap file, which currently means that it must be fully allocated as
NOCOW with no compression on one device. It must also do the proper
tracking so that ioctls will not interfere with the swap file.
Deactivation clears this tracking.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This is the counterpart to merge_extent_hook, similarly, it's used only
for data/freespace inodes so let's remove it, rename it and call it
directly where necessary. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This callback is used only for data and free space inodes. Such inodes
are guaranteed to have their extent_io_tree::private_data set to the
inode struct. Exploit this fact to directly call the function. Also give
it a more descriptive name. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This is the counterpart to ex-set_bit_hook (now btrfs_set_delalloc_extent),
similar to what was done before remove clear_bit_hook and rename the
function. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This callback is used to properly account delalloc extents for data
inodes (ordinary file inodes and freespace v1 inodes). Those can be
easily identified since they have their extent_io trees ->private_data
member point to the inode. Let's exploit this fact to remove the
needless indirection through extent_io_hooks and directly call the
function. Also give the function a name which reflects its purpose -
btrfs_set_delalloc_extent.
This patch also modified test_find_delalloc so that the extent_io_tree
used for testing doesn't have its ->private_data set which would have
caused a crash in btrfs_set_delalloc_extent due to the btrfs_inode->root
member not being initialised. The old version of the code also didn't
call set_bit_hook since the extent_io ops weren't set for the inode. No
functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This callback was only used in debug builds by btrfs_leak_debug_check.
A better approach is to move its implementation in
btrfs_leak_debug_check and ensure the latter is only executed for extent
tree which have ->private_data set i.e. relate to a data node and not
the btree one. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This callback is ony ever called for data page writeout so there is no
need to actually abstract it via extent_io_ops. Lets just export it,
remove the definition of the callback and call it directly in the
functions that invoke the callback. Also rename the function to
btrfs_writepage_endio_finish_ordered since what it really does is
account finished io in the ordered extent data structures. No
functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This hook is called only from __extent_writepage_io which is already
called only from the data page writeout path. So there is no need to
make an indirect call via extent_io_ops. This patch just removes the
callback definition, exports the callback function and calls it directly
at the only call site. Also give the function a more descriptive name.
No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This callback is called only from writepage_delalloc which in turn is
guaranteed to be called from the data page writeout path. In the end
there is no reason to have the call to this function to be indrected via
the extent_io_ops structure. This patch removes the callback definition,
exports the function and calls it directly. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ rename to btrfs_run_delalloc_range ]
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE8rQSAMVO+zA4DBdWxWXV+ddtWDsFAlvoGIUACgkQxWXV+ddt
WDta6g//UJSLnVskCUwh8VyMdd47QArQnaLJowOH7wQn4Nqj+2hf04mCq/kv05ed
OneTezzONZc/qW9fiJGS+Dp77ln4JIDA1hWHtb/A4t9pYlksSQllJ3oiDUVsCp3q
2EbzrjuNz3iQO6TjKlaHX473CLCMQMXS2OXOUnCkF2maMJSdr86oi+j1UiSnud1/
C7uMYM3hG8nkfEfjjb1COpkS2MmzYcPruF5RDcbT/WOUfylTsjjX1E7rK/ZEqS9P
SUcp4uoZe9BNoyWMASLaM7oHE82day4X9MwQoCQFRcm0kq4CnRAZ8X4lBl+M70iW
7Olii/wNZ2SRiJf3jac/rpxoBHvEskXTHyiHTEmdHp4n1L1pL9GzGYIePQcX7uV1
Tb6ImdUUKCC//fPqyeB7cEk5yxqahmlFD3qZVs6GnQkzKrPE+ChLx+7PgcJC/XVh
C5ogNmJm+NvFOuTrYk9zSXg85B8gWHescDJrvNKVizIjw3nKmqiC+dXZljhzw+p8
HscK9EXsiS8jW9ClfJljXzIa4SeA/i7fQGe4tCKfIrCQ+OqUxWpFCEoxygchinfF
Rw90fJ0jX083oXsnfFcVdQpQ+SLSKka/aIRMvi58WRgLU3trci5NNN4TFg8TYRKP
xBDF/iF3sqXajc+xsjoqLhLioZL3Pa5VDNuhsFdois9M5JSRekU=
=K14u
-----END PGP SIGNATURE-----
Merge tag 'for-4.20-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Several fixes to recent release (4.19, fixes tagged for stable) and
other fixes"
* tag 'for-4.20-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix missing delayed iputs on unmount
Btrfs: fix data corruption due to cloning of eof block
Btrfs: fix infinite loop on inode eviction after deduplication of eof block
Btrfs: fix deadlock on tree root leaf when finding free extent
btrfs: avoid link error with CONFIG_NO_AUTO_INLINE
btrfs: tree-checker: Fix misleading group system information
Btrfs: fix missing data checksums after a ranged fsync (msync)
btrfs: fix pinned underflow after transaction aborted
Btrfs: fix cur_offset in the error case for nocow
When we are writing out a free space cache, during the transaction commit
phase, we can end up in a deadlock which results in a stack trace like the
following:
schedule+0x28/0x80
btrfs_tree_read_lock+0x8e/0x120 [btrfs]
? finish_wait+0x80/0x80
btrfs_read_lock_root_node+0x2f/0x40 [btrfs]
btrfs_search_slot+0xf6/0x9f0 [btrfs]
? evict_refill_and_join+0xd0/0xd0 [btrfs]
? inode_insert5+0x119/0x190
btrfs_lookup_inode+0x3a/0xc0 [btrfs]
? kmem_cache_alloc+0x166/0x1d0
btrfs_iget+0x113/0x690 [btrfs]
__lookup_free_space_inode+0xd8/0x150 [btrfs]
lookup_free_space_inode+0x5b/0xb0 [btrfs]
load_free_space_cache+0x7c/0x170 [btrfs]
? cache_block_group+0x72/0x3b0 [btrfs]
cache_block_group+0x1b3/0x3b0 [btrfs]
? finish_wait+0x80/0x80
find_free_extent+0x799/0x1010 [btrfs]
btrfs_reserve_extent+0x9b/0x180 [btrfs]
btrfs_alloc_tree_block+0x1b3/0x4f0 [btrfs]
__btrfs_cow_block+0x11d/0x500 [btrfs]
btrfs_cow_block+0xdc/0x180 [btrfs]
btrfs_search_slot+0x3bd/0x9f0 [btrfs]
btrfs_lookup_inode+0x3a/0xc0 [btrfs]
? kmem_cache_alloc+0x166/0x1d0
btrfs_update_inode_item+0x46/0x100 [btrfs]
cache_save_setup+0xe4/0x3a0 [btrfs]
btrfs_start_dirty_block_groups+0x1be/0x480 [btrfs]
btrfs_commit_transaction+0xcb/0x8b0 [btrfs]
At cache_save_setup() we need to update the inode item of a block group's
cache which is located in the tree root (fs_info->tree_root), which means
that it may result in COWing a leaf from that tree. If that happens we
need to find a free metadata extent and while looking for one, if we find
a block group which was not cached yet we attempt to load its cache by
calling cache_block_group(). However this function will try to load the
inode of the free space cache, which requires finding the matching inode
item in the tree root - if that inode item is located in the same leaf as
the inode item of the space cache we are updating at cache_save_setup(),
we end up in a deadlock, since we try to obtain a read lock on the same
extent buffer that we previously write locked.
So fix this by using the tree root's commit root when searching for a
block group's free space cache inode item when we are attempting to load
a free space cache. This is safe since block groups once loaded stay in
memory forever, as well as their caches, so after they are first loaded
we will never need to read their inode items again. For new block groups,
once they are created they get their ->cached field set to
BTRFS_CACHE_FINISHED meaning we will not need to read their inode item.
Reported-by: Andrew Nelson <andrew.s.nelson@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/CAPTELenq9x5KOWuQ+fa7h1r3nsJG8vyiTH8+ifjURc_duHh2Wg@mail.gmail.com/
Fixes: 9d66e233c7 ("Btrfs: load free space cache if it exists")
Tested-by: Andrew Nelson <andrew.s.nelson@gmail.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When the cow_file_range fails, the related resources are unlocked
according to the range [start..end), so the unlock cannot be repeated in
run_delalloc_nocow.
In some cases (e.g. cur_offset <= end && cow_start != -1), cur_offset is
not updated correctly, so move the cur_offset update before
cow_file_range.
kernel BUG at mm/page-writeback.c:2663!
Internal error: Oops - BUG: 0 [#1] SMP
CPU: 3 PID: 31525 Comm: kworker/u8:7 Tainted: P O
Hardware name: Realtek_RTD1296 (DT)
Workqueue: writeback wb_workfn (flush-btrfs-1)
task: ffffffc076db3380 ti: ffffffc02e9ac000 task.ti: ffffffc02e9ac000
PC is at clear_page_dirty_for_io+0x1bc/0x1e8
LR is at clear_page_dirty_for_io+0x14/0x1e8
pc : [<ffffffc00033c91c>] lr : [<ffffffc00033c774>] pstate: 40000145
sp : ffffffc02e9af4f0
Process kworker/u8:7 (pid: 31525, stack limit = 0xffffffc02e9ac020)
Call trace:
[<ffffffc00033c91c>] clear_page_dirty_for_io+0x1bc/0x1e8
[<ffffffbffc514674>] extent_clear_unlock_delalloc+0x1e4/0x210 [btrfs]
[<ffffffbffc4fb168>] run_delalloc_nocow+0x3b8/0x948 [btrfs]
[<ffffffbffc4fb948>] run_delalloc_range+0x250/0x3a8 [btrfs]
[<ffffffbffc514c0c>] writepage_delalloc.isra.21+0xbc/0x1d8 [btrfs]
[<ffffffbffc516048>] __extent_writepage+0xe8/0x248 [btrfs]
[<ffffffbffc51630c>] extent_write_cache_pages.isra.17+0x164/0x378 [btrfs]
[<ffffffbffc5185a8>] extent_writepages+0x48/0x68 [btrfs]
[<ffffffbffc4f5828>] btrfs_writepages+0x20/0x30 [btrfs]
[<ffffffc00033d758>] do_writepages+0x30/0x88
[<ffffffc0003ba0f4>] __writeback_single_inode+0x34/0x198
[<ffffffc0003ba6c4>] writeback_sb_inodes+0x184/0x3c0
[<ffffffc0003ba96c>] __writeback_inodes_wb+0x6c/0xc0
[<ffffffc0003bac20>] wb_writeback+0x1b8/0x1c0
[<ffffffc0003bb0f0>] wb_workfn+0x150/0x250
[<ffffffc0002b0014>] process_one_work+0x1dc/0x388
[<ffffffc0002b02f0>] worker_thread+0x130/0x500
[<ffffffc0002b6344>] kthread+0x10c/0x110
[<ffffffc000284590>] ret_from_fork+0x10/0x40
Code: d503201f a9025bb5 a90363b7 f90023b9 (d4210000)
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Robbie Ko <robbieko@synology.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=CiDs
-----END PGP SIGNATURE-----
Merge tag 'for-4.20-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs updates from David Sterba:
"This contains a few minor updates and fixes that were under testing or
arrived shortly after the merge window freeze, mostly stable material"
* tag 'for-4.20-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix use-after-free when dumping free space
Btrfs: fix use-after-free during inode eviction
btrfs: move the dio_sem higher up the callchain
btrfs: don't run delayed_iputs in commit
btrfs: fix insert_reserved error handling
btrfs: only free reserved extent if we didn't insert it
btrfs: don't use ctl->free_space for max_extent_size
btrfs: set max_extent_size properly
btrfs: reset max_extent_size properly
MAINTAINERS: update my email address for btrfs
btrfs: delayed-ref: extract find_first_ref_head from find_ref_head
Btrfs: fix deadlock when writing out free space caches
Btrfs: fix assertion on fsync of regular file when using no-holes feature
Btrfs: fix null pointer dereference on compressed write path error
Pull more ->lookup() cleanups from Al Viro:
"Some ->lookup() instances are still overcomplicating the life
for themselves, open-coding the stuff that would be handled by
d_splice_alias() just fine.
Simplify a couple of such cases caught this cycle and document
d_splice_alias() intended use"
* 'work.lookup' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Document d_splice_alias() calling conventions for ->lookup() users.
simplify btrfs_lookup()
clean erofs_lookup()
At inode.c:evict_inode_truncate_pages(), when we iterate over the
inode's extent states, we access an extent state record's "state" field
after we unlocked the inode's io tree lock. This can lead to a
use-after-free issue because after we unlock the io tree that extent
state record might have been freed due to being merged into another
adjacent extent state record (a previous inflight bio for a read
operation finished in the meanwhile which unlocked a range in the io
tree and cause a merge of extent state records, as explained in the
comment before the while loop added in commit 6ca0709756 ("Btrfs: fix
hang during inode eviction due to concurrent readahead")).
Fix this by keeping a copy of the extent state's flags in a local
variable and using it after unlocking the io tree.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201189
Fixes: b9d0b38928 ("btrfs: Add handler for invalidate page")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we insert the file extent once the ordered extent completes we free
the reserved extent reservation as it'll have been migrated to the
bytes_used counter. However if we error out after this step we'll still
clear the reserved extent reservation, resulting in a negative
accounting of the reserved bytes for the block group and space info.
Fix this by only doing the free if we didn't successfully insert a file
extent for this extent.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
At inode.c:compress_file_range(), under the "free_pages_out" label, we can
end up dereferencing the "pages" pointer when it has a NULL value. This
case happens when "start" has a value of 0 and we fail to allocate memory
for the "pages" pointer. When that happens we jump to the "cont" label and
then enter the "if (start == 0)" branch where we immediately call the
cow_file_range_inline() function. If that function returns 0 (success
creating an inline extent) or an error (like -ENOMEM for example) we jump
to the "free_pages_out" label and then access "pages[i]" leading to a NULL
pointer dereference, since "nr_pages" has a value greater than zero at
that point.
Fix this by setting "nr_pages" to 0 when we fail to allocate memory for
the "pages" pointer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201119
Fixes: 771ed689d2 ("Btrfs: Optimize compressed writeback and reads")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The avg_delayed_ref_runtime can be referenced from the transaction
handle.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It can be referenced from the transaction handle.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We don't need it, rsv->size is set once and never changes throughout
its lifetime, so just use that for the reserve size.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The only aops we define for symlinks are identical to the aops for
regular files. This has been the case since symlink support was added in
commit 2b8d99a723 ("Btrfs: symlinks and hard links"). As far as I can
tell, there wasn't a good reason to have separate aops then, and there
isn't now, so let's just do what most other filesystems do and reuse the
same structure.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
rb_first_cached() trades an extra pointer "leftmost" for doing the
same job as rb_first() but in O(1).
As evict_inode_truncate_pages() removes all extent mapping by always
looking for the first rb entry, it's helpful to use rb_first_cached
instead.
For more details about the optimization see patch "Btrfs: delayed-refs:
use rb_first_cached for href_root".
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In btrfs_orphan_cleanup the final 'if (ret) goto out' cannot ever be
executed. This is due to the last assignment to 'ret' depending on the
return value of btrfs_iget. If an error other than -ENOENT is returned
then the loop is prematurely terminated by 'goto out'. On the other
hand, if the error value is ENOENT then a subsequent if branch is
executed that always re-assigns 'ret' and in case it's an error just
terminates the loop. No functional changes.
Coverity-id: 1437392
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we delete an inode,
btrfs_evict_inode() {
truncate_inode_pages_final()
truncate_inode_pages_range()
lock_page()
truncate_cleanup_page()
btrfs_invalidatepage()
wait_on_page_writeback
btrfs_lookup_ordered_range()
cancel_dirty_page()
unlock_page()
...
btrfs_wait_ordered_range()
...
As VFS has called ->invalidatepage() to get all ordered extents done (if
there are any) and truncated all page cache pages (no dirty pages to
writeback after this step), wait_ordered_range() is just a noop.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Unify the error handling of directory item lookups using IS_ERR_OR_NULL.
No functional changes.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Unless it's going to read inline extents from btree leaf to page,
btrfs_get_extent won't sleep during the period of holding path lock.
This sets leave_spinning at first and sets path to blocking mode right
before reading inline extent if that's the case. The benefit is that a
path in spinning mode typically has lower impact (faster) on waiters
rather than that in the blocking mode.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This fixes btrfs_get_extent to be consistent with our existing
declaration style.
Note: For the record, indentation styles that are accepted are both,
aligning under the opening ( and tab or double tab indentation on the
next line. Preferrably not spliting the type or long expressions in the
argument lists.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
[ add note ]
Signed-off-by: David Sterba <dsterba@suse.com>
Pointer inode is being assigned but is never used hence it is redundant
and can be removed. It's been unused since the introduction in
38c227d87c ("Btrfs: snapshot-aware defrag").
Cleans up clang warning:
variable ‘inode’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
trace_btrfs_get_extent() has nothing to do with path, place
btrfs_free_path ahead so that we can unlock path on error.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
@path is always NULL when it comes to the if branch.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are two members in struct btrfs_root which indicate root's
objectid: objectid and root_key.objectid.
They are both set to the same value in __setup_root():
static void __setup_root(struct btrfs_root *root,
struct btrfs_fs_info *fs_info,
u64 objectid)
{
...
root->objectid = objectid;
...
root->root_key.objectid = objecitd;
...
}
and not changed to other value after initialization.
grep in btrfs directory shows both are used in many places:
$ grep -rI "root->root_key.objectid" | wc -l
133
$ grep -rI "root->objectid" | wc -l
55
(4.17, inc. some noise)
It is confusing to have two similar variable names and it seems
that there is no rule about which should be used in a certain case.
Since ->root_key itself is needed for tree reloc tree, let's remove
'objecitd' member and unify code to use ->root_key.objectid in all places.
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All callers pass the root tree of dir, we can push that down to the
function itself.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Using true and false here is closer to the expected semantic than using
0 and 1. No functional change.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Only when send_in_progress, we have to do something different such as
btrfs_warn() and return -EPERM. Therefore, we could check
send_in_progress first and process error handling, after the
root_item_lock has been got.
Just for better readability. No functional change.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=fu93
-----END PGP SIGNATURE-----
Merge tag 'for-4.19-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix for improper fsync after hardlink
- fix for a corruption during file deduplication
- use after free fixes
- RCU warning fix
- fix for buffered write to nodatacow file
* tag 'for-4.19-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Fix suspicious RCU usage warning in btrfs_debug_in_rcu
btrfs: use after free in btrfs_quota_enable
btrfs: btrfs_shrink_device should call commit transaction at the end
btrfs: fix qgroup_free wrong num_bytes in btrfs_subvolume_reserve_metadata
Btrfs: fix data corruption when deduplicating between different files
Btrfs: sync log after logging new name
Btrfs: fix unexpected failure of nocow buffered writes after snapshotting when low on space
When we add a new name for an inode which was logged in the current
transaction, we update the inode in the log so that its new name and
ancestors are added to the log. However when we do this we do not persist
the log, so the changes remain in memory only, and as a consequence, any
ancestors that were created in the current transaction are updated such
that future calls to btrfs_inode_in_log() return true. This leads to a
subsequent fsync against such new ancestor directories returning
immediately, without persisting the log, therefore after a power failure
the new ancestor directories do not exist, despite fsync being called
against them explicitly.
Example:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ mkdir /mnt/A
$ mkdir /mnt/B
$ mkdir /mnt/A/C
$ touch /mnt/B/foo
$ xfs_io -c "fsync" /mnt/B/foo
$ ln /mnt/B/foo /mnt/A/C/foo
$ xfs_io -c "fsync" /mnt/A
<power failure>
After the power failure, directory "A" does not exist, despite the explicit
fsync on it.
Instead of fixing this by changing the behaviour of the explicit fsync on
directory "A" to persist the log instead of doing nothing, make the logging
of the new file name (which happens when creating a hard link or renaming)
persist the log. This approach not only is simpler, not requiring addition
of new fields to the inode in memory structure, but also gives us the same
behaviour as ext4, xfs and f2fs (possibly other filesystems too).
A test case for fstests follows soon.
Fixes: 12fcfd22fe ("Btrfs: tree logging unlink/rename fixes")
Reported-by: Vijay Chidambaram <vvijay03@gmail.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit e9894fd3e3 ("Btrfs: fix snapshot vs nocow writting") forced
nocow writes to fallback to COW, during writeback, when a snapshot is
created. This resulted in writes made before creating the snapshot to
unexpectedly fail with ENOSPC during writeback when success (0) was
returned to user space through the write system call.
The steps leading to this problem are:
1. When it's not possible to allocate data space for a write, the
buffered write path checks if a NOCOW write is possible. If it is,
it will not reserve space and success (0) is returned to user space.
2. Then when a snapshot is created, the root's will_be_snapshotted
atomic is incremented and writeback is triggered for all inode's that
belong to the root being snapshotted. Incrementing that atomic forces
all previous writes to fallback to COW during writeback (running
delalloc).
3. This results in the writeback for the inodes to fail and therefore
setting the ENOSPC error in their mappings, so that a subsequent
fsync on them will report the error to user space. So it's not a
completely silent data loss (since fsync will report ENOSPC) but it's
a very unexpected and undesirable behaviour, because if a clean
shutdown/unmount of the filesystem happens without previous calls to
fsync, it is expected to have the data present in the files after
mounting the filesystem again.
So fix this by adding a new atomic named snapshot_force_cow to the
root structure which prevents this behaviour and works the following way:
1. It is incremented when we start to create a snapshot after triggering
writeback and before waiting for writeback to finish.
2. This new atomic is now what is used by writeback (running delalloc)
to decide whether we need to fallback to COW or not. Because we
incremented this new atomic after triggering writeback in the
snapshot creation ioctl, we ensure that all buffered writes that
happened before snapshot creation will succeed and not fallback to
COW (which would make them fail with ENOSPC).
3. The existing atomic, will_be_snapshotted, is kept because it is used
to force new buffered writes, that start after we started
snapshotting, to reserve data space even when NOCOW is possible.
This makes these writes fail early with ENOSPC when there's no
available space to allocate, preventing the unexpected behaviour of
writeback later failing with ENOSPC due to a fallback to COW mode.
Fixes: e9894fd3e3 ("Btrfs: fix snapshot vs nocow writting")
Signed-off-by: Robbie Ko <robbieko@synology.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE8rQSAMVO+zA4DBdWxWXV+ddtWDsFAltxe7QACgkQxWXV+ddt
WDswMA//QlRO+Ln5CH+RlT4fyf1RQUQZblWss2zxrmlo1GRI3Ljf2DNsBE3rD7P4
NSiXfHmgkdjcQP6poPLJwHxwkNd4NFXglYg64wWO10RjHGhKglmH6ztU88wsPfr2
2RZv271/NvYIEkEi6kdyy8ilKeWMshOfyj3+PaeapQn67uJfimyiUvDgUgbvwH3c
yj0nVRLP1C7snNj4Atti/rjXMhG+m1UWfjRkZsmqlBp52k2UAcrtiwQK+DS5b9mL
aWLSaGmIcJtSMkNJPQBST9GTWbJfKTpceoCzkT0o3irvQpN2e2flAJ4ireL8q4mN
MvqJ7giPBFHNDcHEzN6VERvsaA1Rx9Vq20ieQl8JAMd4p/bi5ehN3ww+9vau5zCw
Pc8WeKEILKrLYEAgHOnUO1wxHw994Iv5CA26roTQ0HNXQJjyEZ4m40Ch6LzmfKPm
WKcHX14Uw22GKaFEXHTOpRZ0U0d1cMTcn5zaAajGsB9LwcaiLM+OiFSPtDkwUOB9
QGJHklZVXAD1IH9HFPuq85uUtXTLXbxsw1g8phEJGbmaVxxCOAUAXwEk3qxuZNbz
CHL3G5+l3JEXxfoJSbDW60kr8xic7teqQDszqqP2qlqtP15ty2xc9d5Q8MZajSTZ
H1z9+0gfjYYHrGuAp69MtCbdQhhDSqLyivjJJm0HBaKfVNGW2Xg=
=jBaz
-----END PGP SIGNATURE-----
Merge tag 'for-4.19-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs updates from David Sterba:
"Mostly fixes and cleanups, nothing big, though the notable thing is
the inserted/deleted lines delta -1124.
User visible changes:
- allow defrag on opened read-only files that have rw permissions;
similar to what dedupe will allow on such files
Core changes:
- tree checker improvements, reported by fuzzing:
* more checks for: block group items, essential trees
* chunk type validation
* mount time cross-checks that physical and logical chunks match
* switch more error codes to EUCLEAN aka EFSCORRUPTED
Fixes:
- fsync corner case fixes
- fix send failure when root has deleted files still open
- send, fix incorrect file layout after hole punching beyond eof
- fix races between mount and deice scan ioctl, found by fuzzing
- fix deadlock when delayed iput is called from writeback on the same
inode; rare but has been observed in practice, also removes code
- fix pinned byte accounting, using the right percpu helpers; this
should avoid some write IO inefficiency during low space conditions
- don't remove block group that still has pinned bytes
- reset on-disk device stats value after replace, otherwise this
would report stale values for the new device
Cleanups:
- time64_t/timespec64 cleanups
- remove remaining dead code in scrub handling NOCOW extents after
disabling it in previous cycle
- simplify fsync regarding ordered extents logic and remove all the
related code
- remove redundant arguments in order to reduce stack space
consumption
- remove support for V0 type of extents, not in use since 2.6.30
- remove several unused structure members
- fewer indirect function calls by inlining some callbacks
- qgroup rescan timing fixes
- vfs: iget cleanups"
* tag 'for-4.19-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (182 commits)
btrfs: revert fs_devices state on error of btrfs_init_new_device
btrfs: Exit gracefully when chunk map cannot be inserted to the tree
btrfs: Introduce mount time chunk <-> dev extent mapping check
btrfs: Verify that every chunk has corresponding block group at mount time
btrfs: Check that each block group has corresponding chunk at mount time
Btrfs: send, fix incorrect file layout after hole punching beyond eof
btrfs: Use wrapper macro for rcu string to remove duplicate code
btrfs: simplify btrfs_iget
btrfs: lift make_bad_inode into btrfs_iget
btrfs: simplify IS_ERR/PTR_ERR checks
btrfs: btrfs_iget never returns an is_bad_inode inode
btrfs: replace: Reset on-disk dev stats value after replace
btrfs: extent-tree: Remove unused __btrfs_free_block_rsv
btrfs: backref: Use ERR_CAST to return error code
btrfs: Remove redundant btrfs_release_path from btrfs_unlink_subvol
btrfs: Remove root parameter from btrfs_unlink_subvol
btrfs: Remove fs_info from btrfs_add_root_ref
btrfs: Remove fs_info from btrfs_del_root_ref
btrfs: Remove fs_info from btrfs_del_root
btrfs: Remove fs_info from btrfs_delete_delayed_dir_index
...
Pull vfs icache updates from Al Viro:
- NFS mkdir/open_by_handle race fix
- analogous solution for FUSE, replacing the one currently in mainline
- new primitive to be used when discarding halfway set up inodes on
failed object creation; gives sane warranties re icache lookups not
returning such doomed by still not freed inodes. A bunch of
filesystems switched to that animal.
- Miklos' fix for last cycle regression in iget5_locked(); -stable will
need a slightly different variant, unfortunately.
- misc bits and pieces around things icache-related (in adfs and jfs).
* 'work.mkdir' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
jfs: don't bother with make_bad_inode() in ialloc()
adfs: don't put inodes into icache
new helper: inode_fake_hash()
vfs: don't evict uninitialized inode
jfs: switch to discard_new_inode()
ext2: make sure that partially set up inodes won't be returned by ext2_iget()
udf: switch to discard_new_inode()
ufs: switch to discard_new_inode()
btrfs: switch to discard_new_inode()
new primitive: discard_new_inode()
kill d_instantiate_no_diralias()
nfs_instantiate(): prevent multiple aliases for directory inode
Don't open-code iget_failed(), don't bother with btrfs_free_path(NULL),
move handling of positive return values of btrfs_lookup_inode() from
btrfs_read_locked_inode() to btrfs_iget() and kill now obviously
pointless ASSERT() in there.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We don't need to check is_bad_inode() after the call of
btrfs_read_locked_inode() - it's exactly the same as checking return
value for being non-zero.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Sterba <dsterba@suse.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Although it is safe to call this on already released paths with no locks
held or extent buffers, removing the redundant btrfs_release_path is
reasonable.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All callers pass the root tree of dir, we can push that down to the
function itself.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It can be referenced from the passed transaction handle.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It can be referenced from the passed transaction handle.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It can be referenced from the passed transaction handle.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We recently ran into the following deadlock involving
btrfs_write_inode():
[ +0.005066] __schedule+0x38e/0x8c0
[ +0.007144] schedule+0x36/0x80
[ +0.006447] bit_wait+0x11/0x60
[ +0.006446] __wait_on_bit+0xbe/0x110
[ +0.007487] ? bit_wait_io+0x60/0x60
[ +0.007319] __inode_wait_for_writeback+0x96/0xc0
[ +0.009568] ? autoremove_wake_function+0x40/0x40
[ +0.009565] inode_wait_for_writeback+0x21/0x30
[ +0.009224] evict+0xb0/0x190
[ +0.006099] iput+0x1a8/0x210
[ +0.006103] btrfs_run_delayed_iputs+0x73/0xc0
[ +0.009047] btrfs_commit_transaction+0x799/0x8c0
[ +0.009567] btrfs_write_inode+0x81/0xb0
[ +0.008008] __writeback_single_inode+0x267/0x320
[ +0.009569] writeback_sb_inodes+0x25b/0x4e0
[ +0.008702] wb_writeback+0x102/0x2d0
[ +0.007487] wb_workfn+0xa4/0x310
[ +0.006794] ? wb_workfn+0xa4/0x310
[ +0.007143] process_one_work+0x150/0x410
[ +0.008179] worker_thread+0x6d/0x520
[ +0.007490] kthread+0x12c/0x160
[ +0.006620] ? put_pwq_unlocked+0x80/0x80
[ +0.008185] ? kthread_park+0xa0/0xa0
[ +0.007484] ? do_syscall_64+0x53/0x150
[ +0.007837] ret_from_fork+0x29/0x40
Writeback calls:
btrfs_write_inode
btrfs_commit_transaction
btrfs_run_delayed_iputs
If iput() is called on that same inode, evict() will wait for writeback
forever.
btrfs_write_inode() was originally added way back in 4730a4bc5b
("btrfs_dirty_inode") to support O_SYNC writes. However, ->write_inode()
hasn't been used for O_SYNC since 148f948ba8 ("vfs: Introduce new
helpers for syncing after writing to O_SYNC file or IS_SYNC inode"), so
btrfs_write_inode() is actually unnecessary (and leads to a bunch of
unnecessary commits). Get rid of it, which also gets rid of the
deadlock.
CC: stable@vger.kernel.org # 3.2+
Signed-off-by: Josef Bacik <jbacik@fb.com>
[Omar: new commit message]
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The data and metadata callback implementation both use the same
function. We can remove the call indirection and intermediate helper
completely.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The data and metadata callback implementation both use the same
function. We can remove the call indirection completely.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All implementations of the callback are trivial and do the same and
there's only one user. Merge everything together.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The end_io callbacks passed to btrfs_wq_submit_bio
(btrfs_submit_bio_done and btree_submit_bio_done) are effectively the
same code, there's no point to do the indirection. Export
btrfs_submit_bio_done and call it directly.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Functions that get btrfs inode can simply reach the fs_info by
dereferencing the root and this looks a bit more straightforward
compared to the btrfs_sb(...) indirection.
If the transaction handle is available and not NULL it's used instead.
Signed-off-by: David Sterba <dsterba@suse.com>
There are several places when the btrfs inode is converted to the
generic inode, back to btrfs and then passed to btrfs_ino. We can remove
the extra back and forth conversions.
Signed-off-by: David Sterba <dsterba@suse.com>
While the regular inode timestamps all use timespec64 now, the i_otime
field is btrfs specific and still needs to be converted to correctly
represent times beyond 2038.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We used to call btrfs_file_extent_inline_len() to get the uncompressed
data size of an inlined extent.
However this function is hiding evil, for compressed extent, it has no
choice but to directly read out ram_bytes from btrfs_file_extent_item.
While for uncompressed extent, it uses item size to calculate the real
data size, and ignoring ram_bytes completely.
In fact, for corrupted ram_bytes, due to above behavior kernel
btrfs_print_leaf() can't even print correct ram_bytes to expose the bug.
Since we have the tree-checker to verify all EXTENT_DATA, such mismatch
can be detected pretty easily, thus we can trust ram_bytes without the
evil btrfs_file_extent_inline_len().
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=KWL7
-----END PGP SIGNATURE-----
Merge tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We have a few regression fixes for qgroup rescan status tracking and
the vm_fault_t conversion that mixed up the error values"
* tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix mount failure when qgroup rescan is in progress
Btrfs: fix regression in btrfs_page_mkwrite() from vm_fault_t conversion
btrfs: quota: Set rescan progress to (u64)-1 if we hit last leaf
The vm_fault_t conversion commit introduced a ret2 variable for tracking
the integer return values from internal btrfs functions. It was
sometimes returning VM_FAULT_LOCKED for pages that were actually invalid
and had been removed from the radix. Something like this:
ret2 = btrfs_delalloc_reserve_space() // returns zero on success
lock_page(page)
if (page->mapping != inode->i_mapping)
goto out_unlock;
...
out_unlock:
if (!ret2) {
...
return VM_FAULT_LOCKED;
}
This ends up triggering this WARNING in btrfs_destroy_inode()
WARN_ON(BTRFS_I(inode)->block_rsv.size);
xfstests generic/095 was able to reliably reproduce the errors.
Since out_unlock: is only used for errors, this fix moves it below the
if (!ret2) check we use to return VM_FAULT_LOCKED for success.
Fixes: a528a24150 (btrfs: change return type of btrfs_page_mkwrite to vm_fault_t)
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=fCdm
-----END PGP SIGNATURE-----
Merge tag 'for-4.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Two regression fixes and an incorrect error value propagation fix from
'rename exchange'"
* tag 'for-4.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix return value on rename exchange failure
btrfs: fix invalid-free in btrfs_extent_same
Btrfs: fix physical offset reported by fiemap for inline extents
If we failed during a rename exchange operation after starting/joining a
transaction, we would end up replacing the return value, stored in the
local 'ret' variable, with the return value from btrfs_end_transaction().
So this could end up returning 0 (success) to user space despite the
operation having failed and aborted the transaction, because if there are
multiple tasks having a reference on the transaction at the time
btrfs_end_transaction() is called by the rename exchange, that function
returns 0 (otherwise it returns -EIO and not the original error value).
So fix this by not overwriting the return value on error after getting
a transaction handle.
Fixes: cdd1fedf82 ("btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT")
CC: stable@vger.kernel.org # 4.9+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This is a late set of changes from Deepa Dinamani doing an automated
treewide conversion of the inode and iattr structures from 'timespec'
to 'timespec64', to push the conversion from the VFS layer into the
individual file systems.
There were no conflicts between this and the contents of linux-next
until just before the merge window, when we saw multiple problems:
- A minor conflict with my own y2038 fixes, which I could address
by adding another patch on top here.
- One semantic conflict with late changes to the NFS tree. I addressed
this by merging Deepa's original branch on top of the changes that
now got merged into mainline and making sure the merge commit includes
the necessary changes as produced by coccinelle.
- A trivial conflict against the removal of staging/lustre.
- Multiple conflicts against the VFS changes in the overlayfs tree.
These are still part of linux-next, but apparently this is no longer
intended for 4.18 [1], so I am ignoring that part.
As Deepa writes:
The series aims to switch vfs timestamps to use struct timespec64.
Currently vfs uses struct timespec, which is not y2038 safe.
The series involves the following:
1. Add vfs helper functions for supporting struct timepec64 timestamps.
2. Cast prints of vfs timestamps to avoid warnings after the switch.
3. Simplify code using vfs timestamps so that the actual
replacement becomes easy.
4. Convert vfs timestamps to use struct timespec64 using a script.
This is a flag day patch.
Next steps:
1. Convert APIs that can handle timespec64, instead of converting
timestamps at the boundaries.
2. Update internal data structures to avoid timestamp conversions.
Thomas Gleixner adds:
I think there is no point to drag that out for the next merge window.
The whole thing needs to be done in one go for the core changes which
means that you're going to play that catchup game forever. Let's get
over with it towards the end of the merge window.
[1] https://www.spinics.net/lists/linux-fsdevel/msg128294.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CZX2
-----END PGP SIGNATURE-----
Merge tag 'vfs-timespec64' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground
Pull inode timestamps conversion to timespec64 from Arnd Bergmann:
"This is a late set of changes from Deepa Dinamani doing an automated
treewide conversion of the inode and iattr structures from 'timespec'
to 'timespec64', to push the conversion from the VFS layer into the
individual file systems.
As Deepa writes:
'The series aims to switch vfs timestamps to use struct timespec64.
Currently vfs uses struct timespec, which is not y2038 safe.
The series involves the following:
1. Add vfs helper functions for supporting struct timepec64
timestamps.
2. Cast prints of vfs timestamps to avoid warnings after the switch.
3. Simplify code using vfs timestamps so that the actual replacement
becomes easy.
4. Convert vfs timestamps to use struct timespec64 using a script.
This is a flag day patch.
Next steps:
1. Convert APIs that can handle timespec64, instead of converting
timestamps at the boundaries.
2. Update internal data structures to avoid timestamp conversions'
Thomas Gleixner adds:
'I think there is no point to drag that out for the next merge
window. The whole thing needs to be done in one go for the core
changes which means that you're going to play that catchup game
forever. Let's get over with it towards the end of the merge window'"
* tag 'vfs-timespec64' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground:
pstore: Remove bogus format string definition
vfs: change inode times to use struct timespec64
pstore: Convert internal records to timespec64
udf: Simplify calls to udf_disk_stamp_to_time
fs: nfs: get rid of memcpys for inode times
ceph: make inode time prints to be long long
lustre: Use long long type to print inode time
fs: add timespec64_truncate()
Pull the timespec64 conversion from Deepa Dinamani:
"The series aims to switch vfs timestamps to use
struct timespec64. Currently vfs uses struct timespec,
which is not y2038 safe.
The flag patch applies cleanly. I've not seen the timestamps
update logic change often. The series applies cleanly on 4.17-rc6
and linux-next tip (top commit: next-20180517).
I'm not sure how to merge this kind of a series with a flag patch.
We are targeting 4.18 for this.
Let me know if you have other suggestions.
The series involves the following:
1. Add vfs helper functions for supporting struct timepec64 timestamps.
2. Cast prints of vfs timestamps to avoid warnings after the switch.
3. Simplify code using vfs timestamps so that the actual
replacement becomes easy.
4. Convert vfs timestamps to use struct timespec64 using a script.
This is a flag day patch.
I've tried to keep the conversions with the script simple, to
aid in the reviews. I've kept all the internal filesystem data
structures and function signatures the same.
Next steps:
1. Convert APIs that can handle timespec64, instead of converting
timestamps at the boundaries.
2. Update internal data structures to avoid timestamp conversions."
I've pulled it into a branch based on top of the NFS changes that
are now in mainline, so I could resolve the non-obvious conflict
between the two while merging.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the new return type vm_fault_t for fault handler. For now, this is
just documenting that the function returns a VM_FAULT value rather than
an errno. Once all instances are converted, vm_fault_t will become a
distinct type.
Reference commit 1c8f422059 ("mm: change return type to vm_fault_t")
vmf_error() is the newly introduced inline function in 4.17-rc6.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_truncate() uses two variables for error handling, ret and err (if
this sounds familiar, it's because btrfs_truncate_inode_items() did
something similar). This is error prone, as was made evident by "Btrfs:
fix error handling in btrfs_truncate()". We only have err because we
don't want to mask an error if we call btrfs_update_inode() and
btrfs_end_transaction(), so let's make that its own scoped return
variable and use ret everywhere else.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that the read side is extracted into its own function, do the same
to the write side. This leaves btrfs_get_blocks_direct_write with the
sole purpose of handling common locking required. Also flip the
condition in btrfs_get_blocks_direct_write so that the write case
comes first and we check for if (Create) rather than if (!create). This
is purely subjective but I believe makes reading a bit more "linear".
No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently this function handles both the READ and WRITE dio cases. This
is facilitated by a bunch of 'if' statements, a goto short-circuit
statement and a very perverse aliasing of "!created"(READ) case
by setting lockstart = lockend and checking for lockstart < lockend for
detecting the write. Let's simplify this mess by extracting the
READ-only code into a separate __btrfs_get_block_direct_read function.
This is only the first step, the next one will be to factor out the
write side as well. The end goal will be to have the common locking/
unlocking code in btrfs_get_blocks_direct and then it will call either
the read|write subvariants. No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In cow_file_range(), create_io_em() may fail, but its return value is
not recorded. Then return value may be 0 even it failed which is a
wrong behavior.
Let cow_file_range() return PTR_ERR(em) if create_io_em() failed.
Fixes: 6f9994dbab ("Btrfs: create a helper to create em for IO")
CC: stable@vger.kernel.org # 4.11+
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since commit 7775c8184e ("btrfs: remove unused parameter from
btrfs_subvolume_release_metadata") parameter qgroup_reserved is not used
by caller of function btrfs_subvolume_reserve_metadata. So remove it.
Signed-off-by: Gu JinXiang <gujx@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[Problem description and how we fix it]
We should balance dirty metadata pages at the end of
btrfs_finish_ordered_io, since a small, unmergeable random write can
potentially produce dirty metadata which is multiple times larger than
the data itself. For example, a small, unmergeable 4KiB write may
produce:
16KiB dirty leaf (and possibly 16KiB dirty node) in subvolume tree
16KiB dirty leaf (and possibly 16KiB dirty node) in checksum tree
16KiB dirty leaf (and possibly 16KiB dirty node) in extent tree
Although we do call balance dirty pages in write side, but in the
buffered write path, most metadata are dirtied only after we reach the
dirty background limit (which by far only counts dirty data pages) and
wakeup the flusher thread. If there are many small, unmergeable random
writes spread in a large btree, we'll find a burst of dirty pages
exceeds the dirty_bytes limit after we wakeup the flusher thread - which
is not what we expect. In our machine, it caused out-of-memory problem
since a page cannot be dropped if it is marked dirty.
Someone may worry about we may sleep in btrfs_btree_balance_dirty_nodelay,
but since we do btrfs_finish_ordered_io in a separate worker, it will not
stop the flusher consuming dirty pages. Also, we use different worker for
metadata writeback endio, sleep in btrfs_finish_ordered_io help us throttle
the size of dirty metadata pages.
[Reproduce steps]
To reproduce the problem, we need to do 4KiB write randomly spread in a
large btree. In our 2GiB RAM machine:
1) Create 4 subvolumes.
2) Run fio on each subvolume:
[global]
direct=0
rw=randwrite
ioengine=libaio
bs=4k
iodepth=16
numjobs=1
group_reporting
size=128G
runtime=1800
norandommap
time_based
randrepeat=0
3) Take snapshot on each subvolume and repeat fio on existing files.
4) Repeat step (3) until we get large btrees.
In our case, by observing btrfs_root_item->bytes_used, we have 2GiB of
metadata in each subvolume tree and 12GiB of metadata in extent tree.
5) Stop all fio, take snapshot again, and wait until all delayed work is
completed.
6) Start all fio. Few seconds later we hit OOM when the flusher starts
to work.
It can be reproduced even when using nocow write.
Signed-off-by: Ethan Lien <ethanlien@synology.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
In nocow path, we check if the extent is snapshotted in
btrfs_cross_ref_exist(). We can do the similar check earlier and avoid
unnecessary search into extent tree.
A fio test on a Intel D-1531, 16GB RAM, SSD RAID-5 machine as follows:
[global]
group_reporting
time_based
thread=1
ioengine=libaio
bs=4k
iodepth=32
size=64G
runtime=180
numjobs=8
rw=randwrite
[file1]
filename=/mnt/nocow/testfile
IOPS result: unpatched patched
1 fio round: 46670 46958
snapshot
2 fio round: 51826 54498
3 fio round: 59767 61289
After snapshot, the first fio get about 5% performance gain. As we
continually write to the same file, all writes will resume to nocow mode
and eventually we have no performance gain.
Signed-off-by: Ethan Lien <ethanlien@synology.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
This function always takes a transaction handle which contains a
reference to the fs_info. Use that and remove the extra argument.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
[ rename the function ]
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_link() calls btrfs_orphan_del() if it's linking an O_TMPFILE but
it doesn't reserve space to do so. Even before the removal of the
orphan_block_rsv it wasn't using it.
Fixes: ef3b9af50b ("Btrfs: implement inode_operations callback tmpfile")
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that we don't keep long-standing reservations for orphan items,
root->orphan_block_rsv isn't used. We can git rid of it, along with:
- root->orphan_lock, which was used to protect root->orphan_block_rsv
- root->orphan_inodes, which was used as a refcount for root->orphan_block_rsv
- BTRFS_INODE_ORPHAN_META_RESERVED, which was used to track reservations
in root->orphan_block_rsv
- btrfs_orphan_commit_root(), which was the last user of any of these
and does nothing else
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently, we keep space reserved for all inode orphan items until the
inode is evicted (i.e., all references to it are dropped). We hit an
issue where an application would keep a bunch of deleted files open (by
design) and thus keep a large amount of space reserved, causing ENOSPC
errors when other operations tried to reserve space. This long-standing
reservation isn't absolutely necessary for a couple of reasons:
- We can almost always make the reservation we need or steal from the
global reserve for the orphan item
- If we can't, it's not the end of the world if we drop the orphan item
on the floor and let the next mount clean it up
So, get rid of persistent reservation and just reserve space in
btrfs_evict_inode().
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The truncate loop in btrfs_evict_inode() does two things at once:
- It refills the temporary block reserve, potentially stealing from the
global reserve or committing
- It calls btrfs_truncate_inode_items()
The tangle of continues hides the fact that these two steps are actually
separate. Split the first step out into a separate function both for
clarity and so that we can reuse it in a later patch.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In btrfs_evict_inode(), if btrfs_truncate_inode_items() fails, the inode
item will still be in the tree but we still return the ino to the ino
cache. That will blow up later when someone tries to allocate that ino,
so don't return it to the cache.
Fixes: 581bb05094 ("Btrfs: Cache free inode numbers in memory")
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_orphan_commit_root() tries to delete an orphan item for a
subvolume in the tree root, but we don't actually insert that item in
the first place. See commit 0a0d4415e3 ("Btrfs: delete dead code in
btrfs_orphan_add()"). We can get rid of it.
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that we don't add orphan items for truncate, there can't be races on
adding or deleting an orphan item, so this bit is unnecessary.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently, we insert an orphan item during a truncate so that if there's
a crash, we don't leak extents past the on-disk i_size. However, since
commit 7f4f6e0a3f ("Btrfs: only update disk_i_size as we remove
extents"), we keep disk_i_size in sync with the extent items as we
truncate, so orphan cleanup will never have any extents to remove. Don't
bother with the superfluous orphan item.
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_free_extent() can fail because of ENOMEM. There's no reason to
panic here, we can just abort the transaction.
Fixes: f4b9aa8d3b ("btrfs_truncate")
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_truncate_inode_items() uses two variables for error handling, ret
and err. These are not handled consistently, leading to a couple of
bugs.
- Errors from btrfs_del_items() are handled but not propagated to the
caller
- If btrfs_run_delayed_refs() fails and aborts the transaction, we
continue running
Just use ret everywhere and simplify things a bit, fixing both of these
issues.
Fixes: 79787eaab4 ("btrfs: replace many BUG_ONs with proper error handling")
Fixes: 1262133b8d ("Btrfs: account for crcs in delayed ref processing")
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit a41ad394a0 ("Btrfs: convert to the new truncate sequence")
changed btrfs_setsize() to call truncate_setsize() instead of
vmtruncate() but didn't update the comment above it. truncate_setsize()
never fails (the IS_SWAPFILE() check happens elsewhere), so remove the
comment.
Additionally, the comment above btrfs_page_mkwrite() references
vmtruncate(), but truncate_setsize() does the size write and page
locking now.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function is no longer used outside of inode.c so just make it
static. At the same time give a more becoming name, since it's not
really invalidating the inodes but just calling d_prune_alias. Last,
but not least - move the function above the sole caller to avoid
introducing yet-another-pointless forward declaration.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Use the wrappers and reduce the amount of low-level details about the
waitqueue management.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[spotted while going through ->d_fsdata handling around d_splice_alias();
don't really care which tree that goes through]
The only thing even looking at ->d_fsdata in there (since 2012)
had been kfree(dentry->d_fsdata) in btrfs_dentry_delete(). Which,
incidentally, is all btrfs_dentry_delete() does.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The invariant is that when nr_delalloc_inodes is 0 then the root
mustn't have any inodes on its delalloc inodes list.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's used only in inode.c so makes no sense to have it exported. Also
move the definition of btrfs_delalloc_work to inode.c since it's used
only this file.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When allocating a delalloc work we are always setting the delayed_iput
to 0. So remove the delay_iput member of btrfs_delalloc_work, as a
result also remove it as a parameter from btrfs_alloc_delalloc_work
since it's not used anymore.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's always set to 0 so remove it.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
[ rename to start_delalloc_inodes ]
Signed-off-by: David Sterba <dsterba@suse.com>
It's always set to 0, so just remove it and collapse the constant value
to the only function we are passing it.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
