Hi,
The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.
I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.
I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH. This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.
But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed. Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.
Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull vfs fixes from Al Viro:
"double iput() on failure exit in lustre, racy removal of spliced
dentries from ->s_anon in __d_materialise_dentry() plus a bunch of
assorted RCU pathwalk fixes"
The RCU pathwalk fixes end up fixing a couple of cases where we
incorrectly dropped out of RCU walking, due to incorrect initialization
and testing of the sequence locks in some corner cases. Since dropping
out of RCU walk mode forces the slow locked accesses, those corner cases
slowed down quite dramatically.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
be careful with nd->inode in path_init() and follow_dotdot_rcu()
don't bugger nd->seq on set_root_rcu() from follow_dotdot_rcu()
fix bogus read_seqretry() checks introduced in b37199e
move the call of __d_drop(anon) into __d_materialise_unique(dentry, anon)
[fix] lustre: d_make_root() does iput() on dentry allocation failure
The performance regression that Josef Bacik reported in the pathname
lookup (see commit 99d263d4c5 "vfs: fix bad hashing of dentries") made
me look at performance stability of the dcache code, just to verify that
the problem was actually fixed. That turned up a few other problems in
this area.
There are a few cases where we exit RCU lookup mode and go to the slow
serializing case when we shouldn't, Al has fixed those and they'll come
in with the next VFS pull.
But my performance verification also shows that link_path_walk() turns
out to have a very unfortunate 32-bit store of the length and hash of
the name we look up, followed by a 64-bit read of the combined hash_len
field. That screws up the processor store to load forwarding, causing
an unnecessary hickup in this critical routine.
It's caused by the ugly calling convention for the "hash_name()"
function, and easily fixed by just making hash_name() fill in the whole
'struct qstr' rather than passing it a pointer to just the hash value.
With that, the profile for this function looks much smoother.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull parisc updates from Helge Deller:
"The most important patch is a new Light Weigth Syscall (LWS) for 8,
16, 32 and 64 bit atomic CAS operations which is required in order to
be able to implement the atomic gcc builtins on our platform.
Other than that, we wire up the seccomp, getrandom and memfd_create
syscalls, fixes a minor off-by-one bug and a wrong printk string"
* 'parisc-3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Implement new LWS CAS supporting 64 bit operations.
parisc: Wire up seccomp, getrandom and memfd_create syscalls
parisc: dino: fix %d confusingly prefixed with 0x in format string
parisc: sys_hpux: NUL terminator is one past the end
in the former we simply check if dentry is still valid after picking
its ->d_inode; in the latter we fetch ->d_inode in the same places
where we fetch dentry and its ->d_seq, under the same checks.
Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
return the value instead, and have path_init() do the assignment. Broken by
"vfs: Fix absolute RCU path walk failures due to uninitialized seq number",
which was Cc-stable with 2.6.38+ as destination. This one should go where
it went.
To avoid dummy value returned in case when root is already set (it would do
no harm, actually, since the only caller that doesn't ignore the return value
is guaranteed to have nd->root *not* set, but it's more obvious that way),
lift the check into callers. And do the same to set_root(), to keep them
in sync.
Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
MAINTAINERS to reflect new e-mail address.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uhqP
-----END PGP SIGNATURE-----
Merge tag 'ntb-3.17' of git://github.com/jonmason/ntb
Pull ntb driver bugfixes from Jon Mason:
"NTB driver fixes for queue spread and buffer alignment. Also, update
to MAINTAINERS to reflect new e-mail address"
* tag 'ntb-3.17' of git://github.com/jonmason/ntb:
ntb: Add alignment check to meet hardware requirement
MAINTAINERS: update NTB info
NTB: correct the spread of queues over mw's
Pull ARM irq chip fixes from Thomas Gleixner:
"Another pile of ARM specific irq chip fixlets:
- off by one bugs in the crossbar driver
- missing annotations
- a bunch of "make it compile" updates
I pulled the lot today from Jason, but it has been in -next for at
least a week"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: gic-v3: Declare rdist as __percpu pointer to __iomem pointer
irqchip: gic: Make gic_default_routable_irq_domain_ops static
irqchip: exynos-combiner: Fix compilation error on ARM64
irqchip: crossbar: Off by one bugs in init
irqchip: gic-v3: Tag all low level accessors __maybe_unused
irqchip: gic-v3: Only define gic_peek_irq() when building SMP
The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Update my contact info to my personal email address and add Dave Jiang.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
The detection of an uneven number of queues on the given memory windows
was not correct. The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Pull futex and timer fixes from Thomas Gleixner:
"A oneliner bugfix for the jinxed futex code:
- Drop hash bucket lock in the error exit path. I really could slap
myself for intruducing that bug while fixing all the other horror
in that code three month ago ...
and the timer department is not too proud about the following fixes:
- Deal with a long standing rounding bug in the timeval to jiffies
conversion. It's a real issue and this fix fell through the cracks
for quite some time.
- Another round of alarmtimer fixes. Finally this code gets used
more widely and the subtle issues hidden for quite some time are
noticed and fixed. Nothing really exciting, just the itty bitty
details which bite the serious users here and there"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Unlock hb->lock in futex_wait_requeue_pi() error path
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Lock k_itimer during timer callback
alarmtimer: Do not signal SIGEV_NONE timers
alarmtimer: Return relative times in timer_gettime
jiffies: Fix timeval conversion to jiffies
The current LWS cas only works correctly for 32bit. The new LWS allows
for CAS operations of variable size.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Helge Deller <deller@gmx.de>
Josef Bacik found a performance regression between 3.2 and 3.10 and
narrowed it down to commit bfcfaa77bd ("vfs: use 'unsigned long'
accesses for dcache name comparison and hashing"). He reports:
"The test case is essentially
for (i = 0; i < 1000000; i++)
mkdir("a$i");
On xfs on a fio card this goes at about 20k dir/sec with 3.2, and 12k
dir/sec with 3.10. This is because we spend waaaaay more time in
__d_lookup on 3.10 than in 3.2.
The new hashing function for strings is suboptimal for <
sizeof(unsigned long) string names (and hell even > sizeof(unsigned
long) string names that I've tested). I broke out the old hashing
function and the new one into a userspace helper to get real numbers
and this is what I'm getting:
Old hash table had 1000000 entries, 0 dupes, 0 max dupes
New hash table had 12628 entries, 987372 dupes, 900 max dupes
We had 11400 buckets with a p50 of 30 dupes, p90 of 240 dupes, p99 of 567 dupes for the new hash
My test does the hash, and then does the d_hash into a integer pointer
array the same size as the dentry hash table on my system, and then
just increments the value at the address we got to see how many
entries we overlap with.
As you can see the old hash function ended up with all 1 million
entries in their own bucket, whereas the new one they are only
distributed among ~12.5k buckets, which is why we're using so much
more CPU in __d_lookup".
The reason for this hash regression is two-fold:
- On 64-bit architectures the down-mixing of the original 64-bit
word-at-a-time hash into the final 32-bit hash value is very
simplistic and suboptimal, and just adds the two 32-bit parts
together.
In particular, because there is no bit shuffling and the mixing
boundary is also a byte boundary, similar character patterns in the
low and high word easily end up just canceling each other out.
- the old byte-at-a-time hash mixed each byte into the final hash as it
hashed the path component name, resulting in the low bits of the hash
generally being a good source of hash data. That is not true for the
word-at-a-time case, and the hash data is distributed among all the
bits.
The fix is the same in both cases: do a better job of mixing the bits up
and using as much of the hash data as possible. We already have the
"hash_32|64()" functions to do that.
Reported-by: Josef Bacik <jbacik@fb.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hash_64() function historically does the multiply by the
GOLDEN_RATIO_PRIME_64 number with explicit shifts and adds, because
unlike the 32-bit case, gcc seems unable to turn the constant multiply
into the more appropriate shift and adds when required.
However, that means that we generate those shifts and adds even when the
architecture has a fast multiplier, and could just do it better in
hardware.
Use the now-cleaned-up CONFIG_ARCH_HAS_FAST_MULTIPLIER (together with
"is it a 64-bit architecture") to decide whether to use an integer
multiply or the explicit sequence of shift/add instructions.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It used to be an ad-hoc hack defined by the x86 version of
<asm/bitops.h> that enabled a couple of library routines to know whether
an integer multiply is faster than repeated shifts and additions.
This just makes it use the real Kconfig system instead, and makes x86
(which was the only architecture that did this) select the option.
NOTE! Even for x86, this really is kind of wrong. If we cared, we would
probably not enable this for builds optimized for netburst (P4), where
shifts-and-adds are generally faster than multiplies. This patch does
*not* change that kind of logic, though, it is purely a syntactic change
with no code changes.
This was triggered by the fact that we have other places that really
want to know "do I want to expand multiples by constants by hand or
not", particularly the hash generation code.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
as clean. This could cause no writeback to occur or spurious dirty
block counts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUEG6eAAoJEMUj8QotnQNabuUIALF4UnJov622hmGIcBC91j8m
HRD1gNqu8hOLrtQEP+E7fdrDwHqyxAdL2kFN6nowbvuWmSVAUpQmsLCbXOvQOttx
mELPFSOw2s1FpBbt63pIi8icAPCvzJYeR+jGN3m//b0eVFkmQ6xQGazhbd3JF+xP
mHeEVNTF7acbUYDdfejF8kNJcUbpU63IF5UzRGOXMTNZ2DnFvEiBJHtgXJKiIkhN
MhZNFgqeRdIppoDImnGJ9kQrWzoXGIpAXbxFbvjLofpr6HK2FxWLayeib0Jdm+Ze
znHjSqyRRBhtszk/c8Rxqzy9dotMi3fI/O4pVkziSMYKCjtt9dCRFbP1Gkwaf3w=
=6q2l
-----END PGP SIGNATURE-----
Merge tag 'dm-3.17-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix a race in the DM cache target that caused dirty blocks to be
marked as clean. This could cause no writeback to occur or spurious
dirty block counts"
* tag 'dm-3.17-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: fix race causing dirty blocks to be marked as clean
Pull block fixes from Jens Axboe:
"A small collection of fixes for the current rc series. This contains:
- Two small blk-mq patches from Rob Elliott, cleaning up error case
at init time.
- A fix from Ming Lei, fixing SG merging for blk-mq where
QUEUE_FLAG_SG_NO_MERGE is the default.
- A dev_t minor lifetime fix from Keith, fixing an issue where a
minor might be reused before all references to it were gone.
- Fix from Alan Stern where an unbalanced queue bypass caused SCSI
some headaches when it does a series of add/del on devices without
fully registrering the queue.
- A fix from me for improving the scaling of tag depth in blk-mq if
we are short on memory"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: scale depth and rq map appropriate if low on memory
Block: fix unbalanced bypass-disable in blk_register_queue
block: Fix dev_t minor allocation lifetime
blk-mq: cleanup after blk_mq_init_rq_map failures
blk-mq: pass along blk_mq_alloc_tag_set return values
blk-merge: fix blk_recount_segments
arm64.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJUE0aVAAoJEIlPj0hw4a6QG9oQAO1xew3cWPYpougi/Nd19R70
dawtzs19Edj9CDgUC9OQE1JC7J/jG5ElZb3qFc7ICQl90akgx/d7BTWO/6dMGEzw
PtLc60M1lFY60aNYN6T+DLjUxYtwfq74g6x2RjRI4jLaSREVlsOJnV7b0vo4bLpP
tTLc65+Zo35cWykzImoj7nu5JxBsoJYNPCrKWz3B6nOjDiRf99zRAz2yhEt54ajz
BIfg36WbwyvZie5Nxgxp46Ou1hTsmZHmv5MFHhLga0jHRIRfiWnbrEc2pppI64DA
l7sMkz0MwPXdu/Auq4hHstbnLw7OBqE4PfMvPqs4bK2SVQOPB48W3Q+QwhK59iS5
9ytw9j2EGvdEhTDhRs6FQmqaII/xbyvqMQDmdXwDpBzo/+az656RFMQ4eS5+zLDu
JG+ws9Ozt2WJRFQvWiC8zgYRBKiVBkR6SeEf44WiYjRp9HV9gxIXgAIo7AUoNNjQ
USNd4yEkzqMD4aILekNkFvUm5uu/gzCNdmb1N2iIk1gS9CWh4fEUTNRjUr5tqXiR
9iNacoR4Iz96DjE2ZSLnno+1eq1tRNm8nYo/NFe9+SohlfjiSmsnpTJg8FxmrIer
CeqAYTBgQtO+8HOJL/hM2IdFX5EcT+0TYs3DWmoqxqcgOyhK4AFM1XhUWNLpxquH
y6ojU5lRs/E/L8ycGAGg
=gWAc
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.17-b-rc4-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen ARM bugfix from Stefano Stabellini:
"The patches fix the "xen_add_mach_to_phys_entry: cannot add" bug that
has been affecting xen on arm and arm64 guests since 3.16. They
require a few hypervisor side changes that just went in xen-unstable.
A couple of days ago David sent out a pull request with a few other
Xen fixes (it is already in master). Sorry we didn't synchronized
better among us"
* tag 'stable/for-linus-3.17-b-rc4-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/arm: remove mach_to_phys rbtree
xen/arm: reimplement xen_dma_unmap_page & friends
xen/arm: introduce XENFEAT_grant_map_identity
Locks the k_itimer's it_lock member when handling the alarm timer's
expiry callback.
The regular posix timers defined in posix-timers.c have this lock held
during timout processing because their callbacks are routed through
posix_timer_fn(). The alarm timers follow a different path, so they
ought to grab the lock somewhere else.
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sharvil Nanavati <sharvil@google.com>
Signed-off-by: Richard Larocque <rlarocque@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Avoids sending a signal to alarm timers created with sigev_notify set to
SIGEV_NONE by checking for that special case in the timeout callback.
The regular posix timers avoid sending signals to SIGEV_NONE timers by
not scheduling any callbacks for them in the first place. Although it
would be possible to do something similar for alarm timers, it's simpler
to handle this as a special case in the timeout.
Prior to this patch, the alarm timer would ignore the sigev_notify value
and try to deliver signals to the process anyway. Even worse, the
sanity check for the value of sigev_signo is skipped when SIGEV_NONE was
specified, so the signal number could be bogus. If sigev_signo was an
unitialized value (as it often would be if SIGEV_NONE is used), then
it's hard to predict which signal will be sent.
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sharvil Nanavati <sharvil@google.com>
Signed-off-by: Richard Larocque <rlarocque@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Returns the time remaining for an alarm timer, rather than the time at
which it is scheduled to expire. If the timer has already expired or it
is not currently scheduled, the it_value's members are set to zero.
This new behavior matches that of the other posix-timers and the POSIX
specifications.
This is a change in user-visible behavior, and may break existing
applications. Hopefully, few users rely on the old incorrect behavior.
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sharvil Nanavati <sharvil@google.com>
Signed-off-by: Richard Larocque <rlarocque@google.com>
[jstultz: minor style tweak]
Signed-off-by: John Stultz <john.stultz@linaro.org>
timeval_to_jiffies tried to round a timeval up to an integral number
of jiffies, but the logic for doing so was incorrect: intervals
corresponding to exactly N jiffies would become N+1. This manifested
itself particularly repeatedly stopping/starting an itimer:
setitimer(ITIMER_PROF, &val, NULL);
setitimer(ITIMER_PROF, NULL, &val);
would add a full tick to val, _even if it was exactly representable in
terms of jiffies_ (say, the result of a previous rounding.) Doing
this repeatedly would cause unbounded growth in val. So fix the math.
Here's what was wrong with the conversion: we essentially computed
(eliding seconds)
jiffies = usec * (NSEC_PER_USEC/TICK_NSEC)
by using scaling arithmetic, which took the best approximation of
NSEC_PER_USEC/TICK_NSEC with denominator of 2^USEC_JIFFIE_SC =
x/(2^USEC_JIFFIE_SC), and computed:
jiffies = (usec * x) >> USEC_JIFFIE_SC
and rounded this calculation up in the intermediate form (since we
can't necessarily exactly represent TICK_NSEC in usec.) But the
scaling arithmetic is a (very slight) *over*approximation of the true
value; that is, instead of dividing by (1 usec/ 1 jiffie), we
effectively divided by (1 usec/1 jiffie)-epsilon (rounding
down). This would normally be fine, but we want to round timeouts up,
and we did so by adding 2^USEC_JIFFIE_SC - 1 before the shift; this
would be fine if our division was exact, but dividing this by the
slightly smaller factor was equivalent to adding just _over_ 1 to the
final result (instead of just _under_ 1, as desired.)
In particular, with HZ=1000, we consistently computed that 10000 usec
was 11 jiffies; the same was true for any exact multiple of
TICK_NSEC.
We could possibly still round in the intermediate form, adding
something less than 2^USEC_JIFFIE_SC - 1, but easier still is to
convert usec->nsec, round in nanoseconds, and then convert using
time*spec*_to_jiffies. This adds one constant multiplication, and is
not observably slower in microbenchmarks on recent x86 hardware.
Tested: the following program:
int main() {
struct itimerval zero = {{0, 0}, {0, 0}};
/* Initially set to 10 ms. */
struct itimerval initial = zero;
initial.it_interval.tv_usec = 10000;
setitimer(ITIMER_PROF, &initial, NULL);
/* Save and restore several times. */
for (size_t i = 0; i < 10; ++i) {
struct itimerval prev;
setitimer(ITIMER_PROF, &zero, &prev);
/* on old kernels, this goes up by TICK_USEC every iteration */
printf("previous value: %ld %ld %ld %ld\n",
prev.it_interval.tv_sec, prev.it_interval.tv_usec,
prev.it_value.tv_sec, prev.it_value.tv_usec);
setitimer(ITIMER_PROF, &prev, NULL);
}
return 0;
}
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul Turner <pjt@google.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Paul Turner <pjt@google.com>
Reported-by: Aaron Jacobs <jacobsa@google.com>
Signed-off-by: Andrew Hunter <ahh@google.com>
[jstultz: Tweaked to apply to 3.17-rc]
Signed-off-by: John Stultz <john.stultz@linaro.org>
futex_wait_requeue_pi() calls futex_wait_setup(). If
futex_wait_setup() succeeds it returns with hb->lock held and
preemption disabled. Now the sanity check after this does:
if (match_futex(&q.key, &key2)) {
ret = -EINVAL;
goto out_put_keys;
}
which releases the keys but does not release hb->lock.
So we happily return to user space with hb->lock held and therefor
preemption disabled.
Unlock hb->lock before taking the exit route.
Reported-by: Dave "Trinity" Jones <davej@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1409112318500.4178@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Here is one misc driver fix for 3.17-rc5. It resolves a kernel oops
that can happen in the lattice FPGA driver if the firmware isn't
present on the system.
It's been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQTOR4ACgkQMUfUDdst+ylXvACeKk2PemIzfaUoGTmgkGoOioX4
BIsAoLE2jr9/ivh9r+0hkudNGnmBzVI4
=PSdY
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fix from Greg KH:
"Here is one misc driver fix for 3.17-rc5. It resolves a kernel oops
that can happen in the lattice FPGA driver if the firmware isn't
present on the system.
It's been in the linux-next tree for a while now"
* tag 'char-misc-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Lattice ECP3 FPGA: Check firmware pointer
Here are 3 tiny staging driver fixes for 3.17-rc5. Two are fixes for
the imx-drm driver, resolving issues that have been reported. The other
is a memory leak fix for the Android sync driver, due to changes that
went into 3.17-rc1.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQTOKgACgkQMUfUDdst+ykAowCg1HK4Ur/8WFty0TQyaZiz3sTX
j0sAnRBGo8Cqe1hPk5D5WADTdyuTYVtv
=TvOc
-----END PGP SIGNATURE-----
Merge tag 'staging-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are 3 tiny staging driver fixes for 3.17-rc5.
Two are fixes for the imx-drm driver, resolving issues that have been
reported. The other is a memory leak fix for the Android sync driver,
due to changes that went into 3.17-rc1.
All have been in linux-next for a while"
* tag 'staging-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
android: fix reference leak in sync_fence_create
imx-drm: imx-ldb: fix NULL pointer in imx_ldb_unbind()
imx-drm: ipuv3-plane: fix ipu_plane_dpms()
Here are 3 patches for 3.17-rc5. Two serial driver fixes that resolve
some reported issues, and one new device id.
All have been in linux-next just fine.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQTNocACgkQMUfUDdst+ylSFQCfcarOgwBv2UaO9rR7IxrBXL5P
z5AAnR5wa7Ip5UpfSyqhg67qg42ffq2J
=G50/
-----END PGP SIGNATURE-----
Merge tag 'tty-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are 3 patches for 3.17-rc5. Two serial driver fixes that resolve
some reported issues, and one new device id.
All have been in linux-next just fine"
* tag 'tty-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: xuartps: Fix tx_emtpy() callback
tty/serial: at91: BUG: disable interrupts when !UART_ENABLE_MS()
serial: 8250_dw: Add ACPI ID for Intel Braswell
Here are some USB and PHY fixes for 3.17-rc5.
Nothing major here, just a number of tiny fixes for reported issues, and
some new device ids as well.
All have been tested in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQTNfsACgkQMUfUDdst+yk2ZwCfQOF5dNNui7FbtSWWy6h82CBN
25YAoKXJtipABRJo5q+bztCIDYGk0PgA
=4Ial
-----END PGP SIGNATURE-----
Merge tag 'usb-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB and PHY fixes for 3.17-rc5.
Nothing major here, just a number of tiny fixes for reported issues,
and some new device ids as well.
All have been tested in linux-next"
* tag 'usb-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (46 commits)
xhci: fix oops when xhci resumes from hibernate with hw lpm capable devices
usb: xhci: Fix OOPS in xhci error handling code
xhci: Fix null pointer dereference if xhci initialization fails
storage: Add single-LUN quirk for Jaz USB Adapter
uas: Add missing le16_to_cpu calls to asm1051 / asm1053 usb-id check
usb: chipidea: msm: Initialize PHY on reset event
usb: chipidea: msm: Use USB PHY API to control PHY state
usb: hub: take hub->hdev reference when processing from eventlist
uas: Disable uas on ASM1051 devices
usb: dwc2/gadget: avoid disabling ep0
usb: dwc2/gadget: delay enabling irq once hardware is configured properly
usb: dwc2/gadget: do not call disconnect method in pullup
usb: dwc2/gadget: break infinite loop in endpoint disable code
usb: dwc2/gadget: fix phy initialization sequence
usb: dwc2/gadget: fix phy disable sequence
uwb: init beacon cache entry before registering uwb device
USB: ftdi_sio: Add support for GE Healthcare Nemo Tracker device
USB: document the 'u' flag for usb-storage quirks parameter
usb: host: xhci: fix compliance mode workaround
usb: dwc3: fix TRB completion when multiple TRBs are started
...
Pull btrfs fixes from Chris Mason:
"Filipe is doing a careful pass through fsync problems, and these are
the fixes so far. I'll have one more for rc6 that we're still
testing.
My big commit is fixing up some inode hash races that Al Viro found
(thanks Al)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use insert_inode_locked4 for inode creation
Btrfs: fix fsync data loss after a ranged fsync
Btrfs: kfree()ing ERR_PTRs
Btrfs: fix crash while doing a ranged fsync
Btrfs: fix corruption after write/fsync failure + fsync + log recovery
Btrfs: fix autodefrag with compression
Just a couple of stragglers here:
- Fix an issue migrating interrupts on CPU hotplug
- Fix a potential information leak of TLS registers across an exec
(Nathan has sent a corresponding patch for arch/arm/ to rmk)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJUEfKCAAoJELescNyEwWM0I/8H/RLpR9kvk0npB8lroFJZUJfa
yIveU5kWnFpEpycjkDDHTYmXbbAMni1t6wII4ofMErDtMkJMW3y11gAp2iUEdP8w
YNGSO9WV8uddbEamoDnO1jMS2eE1sHSSFjXN5529ygM00mAdSq/sIYUkGrjkbRmo
6DHWFvaHYjZDIAb1teFFqtuaL5c4SX+DTwInqwO0hXIPXfgjmSD9PDk8KXJN0Qiu
daX3sNHlFyb4Bh4Q2/aIvQHrkFPVcNUnekCwNoHGgYJ/FMjTV67Kb5SmnlV41rSu
GU4dUuc26gumgrOQ9Yhob2AU6RhC4Auuht7ck+STZWy5kllmjX5TLZMLXmrLIRM=
=0A4L
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Just a couple of stragglers here:
- fix an issue migrating interrupts on CPU hotplug
- fix a potential information leak of TLS registers across an exec
(Nathan has sent a corresponding patch for arch/arm/ to rmk)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: flush TLS registers during exec
arm64: use irq_set_affinity with force=false when migrating irqs
Including:
* Two fixes for issues found by Coverity
* Various fixes for the ARM SMMU driver
* A warning fix for the FSL PAMU driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=jHx2
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- two fixes for issues found by Coverity
- various fixes for the ARM SMMU driver
- a warning fix for the FSL PAMU driver
* tag 'iommu-fixes-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/fsl: Fix warning resulting from adding PCI device twice
iommu/arm-smmu: fix corner cases in address size calculations
iommu/arm-smmu: fix decimal printf format specifiers prefixed with 0x
iommu/arm-smmu: Do not access non-existing S2CR registers
iommu/arm-smmu: fix s2cr and smr teardown on device detach from domain
iommu/arm-smmu: remove pgtable_page_{c,d}tor()
iommu/arm-smmu: fix programming of SMMU_CBn_TCR for stage 1
iommu/arm-smmu: avoid calling request_irq in atomic context
iommu/vt-d: Check return value of acpi_bus_get_device()
iommu/core: Make iommu_group_get_for_dev() more robust
Minor fixes for amba-clcd and video DT bindings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=u5mP
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
"Minor fixes for amba-clcd and video DT bindings"
* tag 'fbdev-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: ARM CLCD: Fix color model capabilities for DT platforms
video: fix composite video connector compatible string
Pull drm fixes from Dave Airlie:
"AST, i915, radeon and msm fixes, all over the place.
All fixing build issues, regressions, oopses or failure to detect
cards"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ast: AST2000 cannot be detected correctly
drm/ast: open key before detect chips
drm/msm: don't crash if no msm.vram param
drm/msm/hdmi: fix build break on non-CCF platforms
drm/msm: Change nested function to static function
drm/radeon/dpm: set the thermal type properly for special configs
drm/radeon: reduce memory footprint for debugging
drm/radeon: add connector quirk for fujitsu board
drm/radeon: fix semaphore value init
drm/radeon: only use me/pfp sync on evergreen+
drm/i915: Wait for vblank before enabling the TV encoder
drm/i915: Evict CS TLBs between batches
drm/i915: Fix irq enable tracking in driver load
drm/i915: Fix EIO/wedged handling in gem fault handler
drm/i915: Prevent recursive deadlock on releasing a busy userptr
This fixes CVE-2014-3631.
It is possible for an associative array to end up with a shortcut node at the
root of the tree if there are more than fan-out leaves in the tree, but they
all crowd into the same slot in the lowest level (ie. they all have the same
first nibble of their index keys).
When assoc_array_gc() returns back up the tree after scanning some leaves, it
can fall off of the root and crash because it assumes that the back pointer
from a shortcut (after label ascend_old_tree) must point to a normal node -
which isn't true of a shortcut node at the root.
Should we find we're ascending rootwards over a shortcut, we should check to
see if the backpointer is zero - and if it is, we have completed the scan.
This particular bug cannot occur if the root node is not a shortcut - ie. if
you have fewer than 17 keys in a keyring or if you have at least two keys that
sit into separate slots (eg. a keyring and a non keyring).
This can be reproduced by:
ring=`keyctl newring bar @s`
for ((i=1; i<=18; i++)); do last_key=`keyctl newring foo$i $ring`; done
keyctl timeout $last_key 2
Doing this:
echo 3 >/proc/sys/kernel/keys/gc_delay
first will speed things up.
If we do fall off of the top of the tree, we get the following oops:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: [<ffffffff8136cea7>] assoc_array_gc+0x2f7/0x540
PGD dae15067 PUD cfc24067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: xt_nat xt_mark nf_conntrack_netbios_ns nf_conntrack_broadcast ip6t_rpfilter ip6t_REJECT xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_ni
CPU: 0 PID: 26011 Comm: kworker/0:1 Not tainted 3.14.9-200.fc20.x86_64 #1
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: events key_garbage_collector
task: ffff8800918bd580 ti: ffff8800aac14000 task.ti: ffff8800aac14000
RIP: 0010:[<ffffffff8136cea7>] [<ffffffff8136cea7>] assoc_array_gc+0x2f7/0x540
RSP: 0018:ffff8800aac15d40 EFLAGS: 00010206
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff8800aaecacc0
RDX: ffff8800daecf440 RSI: 0000000000000001 RDI: ffff8800aadc2bc0
RBP: ffff8800aac15da8 R08: 0000000000000001 R09: 0000000000000003
R10: ffffffff8136ccc7 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000070 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff88011fc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000018 CR3: 00000000db10d000 CR4: 00000000000006f0
Stack:
ffff8800aac15d50 0000000000000011 ffff8800aac15db8 ffffffff812e2a70
ffff880091a00600 0000000000000000 ffff8800aadc2bc3 00000000cd42c987
ffff88003702df20 ffff88003702dfa0 0000000053b65c09 ffff8800aac15fd8
Call Trace:
[<ffffffff812e2a70>] ? keyring_detect_cycle_iterator+0x30/0x30
[<ffffffff812e3e75>] keyring_gc+0x75/0x80
[<ffffffff812e1424>] key_garbage_collector+0x154/0x3c0
[<ffffffff810a67b6>] process_one_work+0x176/0x430
[<ffffffff810a744b>] worker_thread+0x11b/0x3a0
[<ffffffff810a7330>] ? rescuer_thread+0x3b0/0x3b0
[<ffffffff810ae1a8>] kthread+0xd8/0xf0
[<ffffffff810ae0d0>] ? insert_kthread_work+0x40/0x40
[<ffffffff816ffb7c>] ret_from_fork+0x7c/0xb0
[<ffffffff810ae0d0>] ? insert_kthread_work+0x40/0x40
Code: 08 4c 8b 22 0f 84 bf 00 00 00 41 83 c7 01 49 83 e4 fc 41 83 ff 0f 4c 89 65 c0 0f 8f 5a fe ff ff 48 8b 45 c0 4d 63 cf 49 83 c1 02 <4e> 8b 34 c8 4d 85 f6 0f 84 be 00 00 00 41 f6 c6 01 0f 84 92
RIP [<ffffffff8136cea7>] assoc_array_gc+0x2f7/0x540
RSP <ffff8800aac15d40>
CR2: 0000000000000018
---[ end trace 1129028a088c0cbd ]---
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
The DT-based panel capabilities selection was picking up
a subset of available modes based on hardware configuration.
This was wrong, as the capabilities describe available
memory models and adapt the display controller to them
that the RGB output is wired up correctly (as in: R and
B components are not swapped).
This patch fixes it by removing the unnecessary limitation.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
ST SPEAR1340-MIPHY support should be available only on
ST SPEAr1340 machine.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
ST SPEAR1310-MIPHY support should be available only on
ST SPEAr1310 machine.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We index the RX/TX speed select values in the following way:
rx_tx_spd[miphy_phy->sata_gen];
However rx_tx_spd[] starts at index zero and the SATA_GENx's start
at one. In this patch we pad out the first element in rx_tx_spd[]
in an attempt to realign the values.
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Reported-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Type error and cause AST2000 cannot be detected correctly
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Reviewed-by: Egbert Eich <eich@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some config settings like 3rd TX chips will not get correctly
if the extended reg is protected
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Reviewed-by: Egbert Eich <eich@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
