Add pin groups for all three SDHI interfaces and two alternative pin
groups for the MMCIF interface on the sh7372 SoC.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
When setting a pin direction verify that the requested direction is
supported, and return an error if it isn't.
This requires pin configuration information to be supplied by SoC data.
The check is a no-op if the information is not supplied.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Set pin configuration type to
- PINMUX_TYPE_NONE at initialization time and when disabling a function
or freeing a GPIO
- PINMUX_TYPE_FUNCTION when enabling a function
- PINMUX_TYPE_INPUT or PINMUX_TYPE_OUTPUT when setting the GPIO
direction
Verify that the type is PINMUX_TYPE_NONE when enabling a function or
requesting a GPIO and return -EBUSY if it isn't.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The sh_pfc_reconfig_pin() is only called from a single location. Merge
it into its call site to make the code easier to follow.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The existing PFC pinconf implementation, tied to the PFC-specific pin
types, isn't used by drivers or boards. Replace it with the generic
pinconf types to implement bias (pull-up/down) setup. Other pin
configuration options can be implemented later if needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
None of the SoC data need to be modified. Constify it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The purpose of the dry-run is to ensure that a pin about to be
configured isn't in use. However, the current implementation is a no-op.
This proves that the dry-run isn't essential. Remove it.
Freeing configuration then becomes a no-op as well. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The sh_pfc_pin structure supplied in SoC data contains information about
pin configuration and name. It's abused to store GPIO data registers
information and pin config type. Move those fields out of the
pinmux_data_reg structure into the new sh_pfc_gpio_pin and
sh_pfc_pin_config structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The pinmux_data_reg structure supplied in SoC data contains information
about data registers. It's abused to store per-device mapped iomem and
shadow values. Move those fields out of the pinmux_data_reg structure
into the per-device sh_pfc_chip structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Now that all PFC platform devices provide memory resources support for
registers without an associated memory resource isn't used anymore. Drop
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All data registers are located in the same memory resource. Locate the
mapped resource at initializat time and use it directly instead of
computing a mapped address for each register. This gets rid of the
mapped_reg field of the pinmux_data_reg structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Move the sh_pfc_setup_data_regs(), sh_pfc_setup_data_reg(),
sh_pfc_get_data_reg(), sh_pfc_read_bit() and sh_pfc_write_bit()
function to gpio.c as they belong to the GPIO implementation. Inline
sh_pfc_read_bit() and sh_pfc_write_bit() in their only call location.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function pinctrl_register() returns NULL not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.
The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The sh-pfc driver exposes one fake group and function per GPIO pin. As
the pinctrl and pinmux APIs are not used by any SuperH and SH Mobile
board or driver, drop the fake groups and functions and replace them by
a real pinctrl and pinmux implementation.
Groups and functions must now be explicitly provided by PFC SoC-specific
data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The PFC GPIO API implementation moved to using port numbers. Replace all
GPIO_PORTx enum usage with the corresponding port number. The GPIO_PORTx
enum values are identical to the port number on this platform.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The PFC GPIO API implementation moved to using port numbers. Replace all
GPIO_PORTx enum usage with the corresponding port number. The GPIO_PORTx
enum values are identical to the port number on this platform.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The PFC GPIO API implementation moved to using port numbers. Replace all
GPIO_PORTx enum usage with the corresponding port number. The GPIO_PORTx
enum values are identical to the port number on this platform.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The PFC GPIO API implementation moved to using port numbers. Replace all
GPIO_PORTx enum usage with the corresponding port number. The GPIO_PORTx
enum values are identical to the port number on this platform.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The SH73A0 SoC has sparse GPIO numbers. Declare the pin numbers ranges
in the PFC SoC data and use the pin numbers in the GPIO API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The PFC driver assumes that the value of the GPIO_PORTxxx enumeration
names are equal to the port number. This isn't true when the port number
space is sparse, as with the SH73A0.
Fix the issue by adding support for pin numbers ranges specified through
SoC data. When no range is specified the driver considers that the PFC
implements a single contiguous range for all pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Adding a GPIO range to a pinctrl device logically belongs to the GPIO
driver. Switch to the right API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This prepares support for sparse pin numbering. The function currently
just performs and indexed lookup in the pins array.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The function is guaranteed to be called with a gpio number smaller than
nr_pins. The condition can the be simplified, and the function inlined.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The PFC core exposes a sh_pfc_config_gpio() function that configures
pinmuxing for a given GPIO (either a real GPIO or a function GPIO).
Handling of real and function GPIOs belong to the GPIO layer, move the
GPIO number to mark translation to the caller and rename the function to
sh_pfc_config_mux().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The macros are defined identically and used in two SoC-specific files,
share them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Instead of converting the GPIO number to an enum_id and looking up IRQ
table entries by enum_id, replace the pinmux_irq enum_ids field with a
gpios field and lookup entries using the GPIO number.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
And drop the pinmux_flag_t typedef.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Register two GPIO chips, one for the real GPIOs and one for the function
GPIOs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
