Before this patch, the freeze code in gfs2 specified GL_NOCACHE in
several places. That's wrong because we always want to know the state
of whether the file system is frozen.
There was also a problem with freeze/thaw transitioning the glock from
frozen (EX) to thawed (SH) because gfs2 will normally grant glocks in EX
to processes that request it in SH mode, unless GL_EXACT is specified.
Therefore, the freeze/thaw code, which tried to reacquire the glock in
SH mode would get the glock in EX mode, and miss the transition from EX
to SH. That made it think the thaw had completed normally, but since the
glock was still cached in EX, other nodes could not freeze again.
This patch removes the GL_NOCACHE flag to allow the freeze glock to be
cached. It also adds the GL_EXACT flag so the glock is fully transitioned
from EX to SH, thereby allowing future freeze operations.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Before this patch, only read-write mounts would grab the freeze
glock in read-only mode, as part of gfs2_make_fs_rw. So the freeze
glock was never initialized. That meant requests to freeze, which
request the glock in EX, were granted without any state transition.
That meant you could mount a gfs2 file system, which is currently
frozen on a different cluster node, in read-only mode.
This patch makes read-only mounts lock the freeze glock in SH mode,
which will block for file systems that are frozen on another node.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Before this patch, function freeze_go_sync, called when promoting
the freeze glock, was testing for the SDF_JOURNAL_LIVE superblock flag.
That's only set for read-write mounts. Read-only mounts don't use a
journal, so the bit is never set, so the freeze never happened.
This patch removes the check for SDF_JOURNAL_LIVE for freeze requests
but still checks it when deciding whether to flush a journal.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
In several places, we used the GIF_ORDERED inode flag to determine
if an inode was on the ordered writes list. However, since we always
held the sd_ordered_lock spin_lock during the manipulation, we can
just as easily check list_empty(&ip->i_ordered) instead.
This allows us to keep more than one ordered writes list to make
journal writing improvements.
This patch eliminates GIF_ORDERED in favor of checking list_empty.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Include linux/slab.h to fix a build error due to kfree() being undefined.
Fixes: 3f02cb2fd9 ("vfio-ccw: Wire up the CRW irq and CRW region")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703022628.6036-1-sean.j.christopherson@intel.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Two critical mm related fixes that affect booting of m68k/ColdFire devices.
Both fix problems caused by recent system init memblock changes.
-----BEGIN PGP SIGNATURE-----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=odtP
-----END PGP SIGNATURE-----
Merge tag 'm68knommu-for-v5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu mm fixes from Greg Ungerer:
"Two critical mm related fixes that affect booting of m68k/ColdFire
devices.
Both fix problems caused by recent system init memblock changes"
* tag 'm68knommu-for-v5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: mm: fix node memblock init
m68k: nommu: register start of the memory with memblock
- Sync dtc to upstream to pick up fixes for I2C bus checks and quiet
warnings
- Various fixes for DT binding check warnings
- A couple of build fixes/improvements for binding checks
- ReST formatting improvements for writing-schema.rst
- Document reference fixes
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAl7+UtkQHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhw78WEACCkLrvgqJ6fkAInzOGz8yXgrVEU2mWYlgD
4mt5K0M7mVeNonuQJDCbFAvmisKTS/Gxjw5234k68aJ/0C7oCRjMhB/wIKgU/gzm
K3mBOI02CAxCZzKvQQloESZV62nUI9wOcRTF3K5BjMsxsGbNBzaZPxP3A9Uku34t
VpY/H23ZXZ1FeWx0OjeMF6lKJP4cWX4l4Ay9Y9oE4m31LXq64Cb5VBBxo70yqJZB
QiTCqBBS+WpTCvbukKn+rCazeRka5evCSC0vlXum4WkifZDMIclke7gS4QjfsJr/
DM6OmAfNRfOyYO6yGKZzU2eu98q/wFggGaqyJ2vn7Ht0CbzWqgrCaQzEN5ksxwak
CKe9KHS/W2PK3nxRFa1GfznEoBsueckkzmv4hxuwafDuBPgt+UPDExbruHvV3qHC
O4W2zdYWJaQE9ZeiBkZmAbDM+cdbzyd0qHFcuNuU7d53Ez+XDpVDhVE2WX3Hiegw
vTLKyId9McvHrYlRZqNgUSbKgqCCPkjfdU5ANAQB7LSFuiolNZgqcDZZ2Jq9nHxS
irX1dvPKgXxTVz4SAZ6vtrPp5ZueSxcgYGkdC6A+3sm7Xi4RdTgHeRrHFDP3QxrE
FoGAb8ZBzGL6EVdiyIDMPSN2rnABKntheixVZ8bQ4yA8BAEKapuoMRAqCedNW9q+
ixQ/tlB83w==
=/l5U
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Sync dtc to upstream to pick up fixes for I2C bus checks and quiet
warnings
- Various fixes for DT binding check warnings
- A couple of build fixes/improvements for binding checks
- ReST formatting improvements for writing-schema.rst
- Document reference fixes
* tag 'devicetree-fixes-for-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: clock: imx: Fix e-mail address
dt-bindings: thermal: k3: Fix the reg property
dt-bindings: thermal: Remove soc unit address
dt-bindings: display: arm: versatile: Pass the sysreg unit name
dt-bindings: usb: aspeed: Remove the leading zeroes
dt-bindings: copy process-schema-examples.yaml to process-schema.yaml
dt-bindings: do not build processed-schema.yaml for 'make dt_binding_check'
dt-bindings: fix error in 'make clean' after 'make dt_binding_check'
dt-bindings: mailbox: zynqmp_ipi: fix unit address
dt-bindings: bus: uniphier-system-bus: fix warning in example
scripts/dtc: Update to upstream version v1.6.0-11-g9d7888cbf19c
doc: devicetree: bindings: fix spelling mistake
docs: dt: minor adjustments at writing-schema.rst
dt: fix reference to olpc,xo1.75-ec.txt
dt: Fix broken references to renamed docs
dt: fix broken links due to txt->yaml renames
dt: update a reference for reneases pcar file renamed to yaml
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXv20ggAKCRCRxhvAZXjc
osYAAQD4Lp5ORPJv5jtYScxRM1RiUh8hp2MBle+4iYCAQX/UowD/QtMPtiLWaMIw
6bMMBAj1gVBmlIOmu7DhBs8hVtKugQY=
=kNpi
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2020-07-02' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull data race annotation from Christian Brauner:
"This contains an annotation patch for a data race in copy_process()
reported by KCSAN when reading and writing nr_threads.
The data race is intentional and benign. This is obvious from the
comment above the relevant code and based on general consensus when
discussing this issue. So simply using data_race() to annotate this as
an intentional race seems the best option"
* tag 'for-linus-2020-07-02' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fork: annotate data race in copy_process()
-----BEGIN PGP SIGNATURE-----
iJYEABYIAD4WIQRE6pSOnaBC00OEHEIaerohdGur0gUCXv4UMCAcamFya2tvLnNh
a2tpbmVuQGxpbnV4LmludGVsLmNvbQAKCRAaerohdGur0kq/AQDC9w/N2eKgCl1S
uxALoPLsc2W5OITMQP/aDQuayd+hWAEA9WYajToL4wP55q23xS3w1fd70lkX58cH
vbP64TyofgI=
=B4wJ
-----END PGP SIGNATURE-----
Merge tag 'tpmdd-next-v5.8-rc4' of git://git.infradead.org/users/jjs/linux-tpmdd
Pull tpm fixes from Jarkko Sakkinen:
"These are just fixes for bugs found lately.
All of them are small scale things here and there, and all of them are
for previous kernel releases (the oldest appeared in v2.6.17)"
* tag 'tpmdd-next-v5.8-rc4' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm_tis: Remove the HID IFX0102
tpm_tis_spi: Prefer async probe
tpm: ibmvtpm: Wait for ready buffer before probing for TPM2 attributes
tpm/st33zp24: fix spelling mistake "drescription" -> "description"
tpm_tis: extra chip->ops check on error path in tpm_tis_core_init
tpm_tis_spi: Don't send anything during flow control
tpm: Fix TIS locality timeout problems
This kselftest fixes update for Linux 5.8-rc4 consists of tpm test
fixes from arkko Sakkinen.
-----BEGIN PGP SIGNATURE-----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=RDv/
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-fixes-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"tpm test fixes from Jarkko Sakkinen"
* tag 'linux-kselftest-fixes-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: tpm: Use /bin/sh instead of /bin/bash
selftests: tpm: Use 'test -e' instead of 'test -f'
Revert "tpm: selftest: cleanup after unseal with wrong auth/policy test"
This kunit fixes update for Linux 5.8-rc4 consists of fixes to build
and run-times failures. Also includes troubleshooting tips updates
to kunit user documentation.
-----BEGIN PGP SIGNATURE-----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=XeG4
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit fixes from Shuah Khan
"Fixes for build and run-times failures.
Also includes troubleshooting tips updates to kunit user
documentation"
* tag 'linux-kselftest-kunit-fixes-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
Documentation: kunit: Add some troubleshooting tips to the FAQ
kunit: kunit_tool: Fix invalid result when build fails
kunit: show error if kunit results are not present
kunit: kunit_config: Fix parsing of CONFIG options with space
Upon a TX timeout handle, if the TX reporter was not able to recover
from the error, reopen the channels. If tried to reopen channels, do not
loop over TX queues for timeout.
With that, the reporters state and separation will better
expose the driver's state.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add helper which retrieves the RQ WQE's head. Use this helper in RX
reporter diagnose callback.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use txrx.h to contain helper function regarding TX/RX. In the coming
patches, I will add more RQ helpers.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change the hierarchy of the RX reporter 'Common config' in the diagnose
output to match the 'Common config' of the TX reporter which reflects
that CQ is a helper to the traffic queues.
Before:
$ devlink health diagnose pci/0000:00:0b.0 reporter rx
Common config:
RQ:
type: 2 stride size: 2048 size: 8
CQ:
stride size: 64 size: 1024
RQs:
...
After:
$ devlink health diagnose pci/0000:00:0b.0 reporter rx
Common config:
RQ:
type: 2 stride size: 2048 size: 8
CQ:
stride size: 64 size: 1024
RQs:
...
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When received a CQE error, the driver inspect the syndrome given by the
firmware. RQ recovery is initiated only as a result of a fatal syndrome;
syndrome which set the RQ into an error state. Hence no need to query
the RQ state at the beginning of the recovery process. Add additional
debug prints before recovering.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
During queue's recovery, driver waits for flush. The flush timeout is
set to 2 seconds. Add a define for this value for the benefit of RX and
TX reporters.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Creation of devlink health reporters is not fatal for mlx5e instance load.
In case of error in reporter's creation, the return value is ignored.
Change all reporters creation functions to return void.
In addition, with this change, a failure in creating a reporter, will not
prevent the driver from trying to create the next reporter in the list.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
leak and a module unloading bug in the /proc/fs/nfsd/clients/ code, and
a compile warning.
-----BEGIN PGP SIGNATURE-----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=wF3M
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.8-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Fixes for a umask bug on exported filesystems lacking ACL support, a
leak and a module unloading bug in the /proc/fs/nfsd/clients/ code,
and a compile warning"
* tag 'nfsd-5.8-1' of git://linux-nfs.org/~bfields/linux:
SUNRPC: Add missing definition of ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE
nfsd: fix nfsdfs inode reference count leak
nfsd4: fix nfsdfs reference count loop
nfsd: apply umask on fs without ACL support
Without CONFIG_STACKTRACE stack_trace_save_tsk() is not defined. Let
get_callchain_entry_for_task() to always return NULL in such cases.
Fixes: fa28dcb82a ("bpf: Introduce helper bpf_get_task_stack()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200703024537.79971-1-songliubraving@fb.com
Fix a typo in SENSORS_IR35221 option: module name should be "ir35221"
instead of "ir35521".
Fixes: 8991ebd9c9 ("hwmon: (pmbus) Add client driver for IR35221")
Cc: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200702221349.18139-1-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
-----BEGIN PGP SIGNATURE-----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=4lvI
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.8-2020-07-01' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"One fix in here, for a regression in 5.7 where a task is waiting in
the kernel for a condition, but that condition won't become true until
task_work is run. And the task_work can't be run exactly because the
task is waiting in the kernel, so we'll never make any progress.
One example of that is registering an eventfd and queueing io_uring
work, and then the task goes and waits in eventfd read with the
expectation that it'll get woken (and read an event) when the io_uring
request completes. The io_uring request is finished through task_work,
which won't get run while the task is looping in eventfd read"
* tag 'io_uring-5.8-2020-07-01' of git://git.kernel.dk/linux-block:
io_uring: use signal based task_work running
task_work: teach task_work_add() to do signal_wake_up()
Edward Cree says:
====================
sfc: prerequisites for EF100 driver, part 3
Continuing on from [1] and [2], this series assembles the last pieces
of the common codebase that will be used by the forthcoming EF100
driver.
Patch #1 also adds a minor feature to EF10 (setting MTU on VFs) since
EF10 supports the same MCDI extension which that feature will use on
EF100.
Patches #5 & #7, while they should have no externally-visible effect
on driver functionality, change how that functionality is implemented
and how the driver represents TXQ configuration internally, so are
not mere cleanup/refactoring like most of these prerequisites have
(from the perspective of the existing sfc driver) been.
Changes in v2:
* Patch #1: use efx_mcdi_set_mtu() directly, instead of as a fallback,
in the mtu_only case (Jakub)
* Patch #3: fix symbol collision in non-modular builds by renaming
interrupt_mode to efx_interrupt_mode (kernel test robot)
* Patch #6: check for failure of netif_set_real_num_[tr]x_queues (Jakub)
* Patch #12: cleaner solution for ethtool drvinfo (Jakub, David)
[1]: https://lore.kernel.org/netdev/20200629.173812.1532344417590172093.davem@davemloft.net/T/
[2]: https://lore.kernel.org/netdev/20200630.130923.402514193016248355.davem@davemloft.net/T/
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have yet another new scheme for NVRAM, and a corresponding new MCDI.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QDMA subsystem on EF100 needs this information.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ethtool_common.o will be built into both sfc and sfc_ef100 drivers,
it can't use KBUILD_MODNAME directly. Instead, make it reference a
string provided by the individual driver code.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously this was only happening in ef10-specific code.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
_down() merely removes all our filters and VLANs, it doesn't free
efx->filter_state itself.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we only allocate VIs for the number of TXQs we actually need, we
cannot naively use "channel * TXQ_TYPES + txq" for the TXQ number, as
this has gaps (when efx->tx_queues_per_channel < EFX_TXQ_TYPES) and
thus overruns the driver's VI allocations, causing the firmware to
reject the MC_CMD_INIT_TXQ based on INSTANCE.
Thus, we distinguish INSTANCE (stored in tx_queue->queue) from LABEL
(tx_queue->label); the former is allocated starting from 0 in
efx_set_channels(), while the latter is simply the txq type (index in
channel->tx_queue array).
To simplify things, rather than changing tx_queues_per_channel after
setting up TXQs, make Siena always probe its HIGHPRI queues at start
of day, rather than deferring it until tc mqprio enables them.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena needs four TX queues (csum * highpri), EF10 needs two (csum),
and EF100 only needs one (as checksumming is controlled entirely by
the transmit descriptor). Rather than having various bits of ad-hoc
code to decide which queues to set up etc., put the knowledge of how
many TXQs a channel has in one place.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of exposing this old module parameter on the new driver (thus
having to keep it forever after for compatibility), let's confine it
to the old one; if we find later that we need the feature, we ought
to support it properly, with ethtool set-channels.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EF100 only supports MSI-X, so there's no need for the new driver to
expose this old module parameter.
Since it's now visible to the linker, we have to rename it internally
to efx_interrupt_mode to avoid symbol collisions in non-modular
builds.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All NICs supported by this driver are capable of MSI-X interrupts (only
Falcon A1 wasn't, and that's now hived off into its own driver), so no
need for a nic-type parameter. Besides, the code that checked it was
buggy anyway (the following assignment that checked min_interrupt_mode
overrode it).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unprivileged functions (such as VFs) may set their MTU by use of the
'control' field of MC_CMD_SET_MAC_EXT, as used in efx_mcdi_set_mtu().
If calling efx_ef10_mac_reconfigure() from efx_change_mtu(), and the
NIC supports the above (SET_MAC_ENHANCED capability), use it rather
than efx_mcdi_set_mac().
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable act is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I would like that Claudiu becomes co-maintainer of the Cadence macb
driver. He's already participating to lots of reviews and enhancements
to this driver and knows the different versions of this controller.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
net: ipa: simplify endpoint programming
Add tests to functions so they don't update undefined endpoint
registers, rather than requiring the caller to avoid calling them.
Move the call to a workaround function required when suspending
inside the function that puts an endpoint into suspend mode. This
requires moving a few functions (which are otherwise unchanged).
Then simplify ipa_endpoint_program() to call essentially all
endpoint register update functions unconditionally.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Have functions that write endpoint configuration registers return
immediately if they are not valid for the direction of transfer for
the endpoint. This allows most of the calls in ipa_endpoint_program()
to be made unconditionally. Reorder the register writes to match
the order of their definition (based on offset).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
