PHYLINK takes care of filing the right information into
state->an_enabled, get rid of the read from the SerDes's BMCR register.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Device Tree is not providing the per-port interrupts, do not fail
during b53_srab_irq_enable() but instead bail out gracefully. The SRAB driver
is used on the BCM5301X (Northstar) platforms which do not yet have the SRAB
interrupts wired up.
Fixes: 16994374a6 ("net: dsa: b53: Make SRAB driver manage port interrupts")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Built-in PHY ports are still being polled, avoid generating spurious
and duplicate events which the PHY library resolves through polling
anyways.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "pause" variable is only initialized on BCM5301x.
Fixes: 5e004460f8 ("net: dsa: b53: Add helper to set link parameters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case B53_SRAB is enabled, but not B53_SERDES, we can get the
following linking error:
ERROR: "b53_serdes_init" [drivers/net/dsa/b53/b53_srab.ko] undefined!
We also need to ifdef the body of b53_srab_serdes_map_lane() since it
would not be used when B53_SERDES is disabled and that would produce a
warning.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Northstar Plus SerDes which is accessed through a
special page of the switch. Since this is something that most people
probably will not want to use, make it a configurable option with a
default on ARCH_BCM_NSP where it is the most useful currently.
The SerDes supports both SGMII and 1000baseX modes for both lanes, and
2500baseX for one of the lanes, and is internally looking like a
seemingly standard MII PHY, except for the few bits that got repurposed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for PHYLINK, things are reasonably straight forward since we
do not yet support SerDes interfaces, that leaves us with just
MLO_AN_PHY and MLO_AN_FIXED to deal with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the logic from b53_adjust_link() responsible for overriding a
given port's link, speed, duplex and pause settings and make two helper
functions to set the port's configuration and the port's link settings.
We will make use of both, as separate functions while adding PHYLINK
support next.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the SRAB driver to manage per-port interrupts. Since we cannot
sleep during b53_io_ops, schedule a workqueue whenever we get a port
specific interrupt. We will later make use of this to call back into
PHYLINK when there is e.g: a link state change.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches expose individual interrupt line(s) for port specific
event(s), allow configuring these interrupts at an appropriate time
during port_enable/disable callbacks where all port specific resources
are known to be set-up and ready for use.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SRAB driver is the default way to communicate with the integrated
switch on iProc platforms and the MMAP driver is the way to communicate
with the integrated switch on DSL BCM63xx and CM BCM33xx.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Omega SoC internal ethernet switch
to the b53 srab driver in the DSA framework.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Broadcom Cygnus SoC, the brcm tag needs to be inserted
in between the mac address and the ether type (should use
'DSA_PROTO_TAG_BRCM') for the packets sent to the internal
b53 switch.
Since the Cygnus was added with the BCM58XX device id and the
BCM58XX uses 'DSA_PROTO_TAG_BRCM_PREPEND', the data path is
broken, due to the incorrect brcm tag location.
Add a new b53 device id (BCM583XX) for Cygnus family to fix the
issue. Add the new device id to the BCM58XX family as Cygnus
is similar to the BCM58XX in most other functionalities.
Fixes: 1160603960 ("net: dsa: b53: Support prepended Broadcom tags")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reported-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the BCM5389 switch connected through MDIO.
Signed-off-by: Damien Thébault <damien.thebault@vitec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the b53 driver to return PHY statistics when the CPU port used is
different than 5, 7 or 8, because those are typically PHY-less on most
devices. This is useful for debugging link problems between the switch
and an external host when using a non standard CPU port number (e.g: 4).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we largely assumed that we were interested in ETH_SS_STATS
type of strings for all ethtool operations, this is about to change with
the introduction of additional string sets, e.g: ETH_SS_PHY_STATS.
Update all functions to take an appropriate stringset argument and act
on it when it is different than ETH_SS_STATS for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparse complains about the following warnings:
drivers/net/dsa/b53/b53_mmap.c:33:31: warning: incorrect type in
initializer (different address spaces)
drivers/net/dsa/b53/b53_mmap.c:33:31: expected unsigned char
[noderef] [usertype] <asn:2>*regs
drivers/net/dsa/b53/b53_mmap.c:33:31: got void *priv
and indeed, while what we are doing is functional, we are dereferencing
a void * pointer into a void __iomem * which is not great. Just use the
defined b53_mmap_priv structure which holds our register base and use
that.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing the port, we allow different ports to have different
statistics. This is useful since some ports have SERDES interfaces
with their own statistic counters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Models such as BCM5395/97/98 and BCM53125/24/53115 and compatible require that
we turn on managed mode to actually act on Broadcom tags, otherwise they just
pass them through on ingress (host -> switch) and don't insert them in egress
(switch -> host). Turning on managed mode is simple, but requires us to
properly support ARL misses on multicast addresses which is a much more
involved set of changes not suitable for a bug fix for this release.
Reported-by: Jochen Friedrich <jochen@scram.de>
Fixes: 7edc58d614 ("net: dsa: b53: Turn on Broadcom tags")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch VLAN ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from VLAN prepare and add operations.
At the same time, fix the following checkpatch warning:
WARNING: line over 80 characters
#74: FILE: drivers/net/dsa/dsa_loop.c:177:
+ const struct switchdev_obj_port_vlan *vlan)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the much more capable b53_get_tag_protocol() which takes care of
all Broadcom switches specifics to resolve which port can have Broadcom
tags enabled or not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BCM58xx devices (Northstar Plus), there is an accelerator attached to
port 8 which would only work if we use prepended Broadcom tags. Resolve
that difference in our get_tag_protocol() function by setting the
appropriate tagging protocol in that case. We need to change
b53_brcm_hdr_setup() a little bit now since we can deal with two types
of Broadcom tags.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers want to check whether the configured CPU port is a
possible configuration for enabling tagging, pass down the CPU port
number so they verify that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Broadcom tags for b53 devices, except 5325 and 5365 which use a
different Broadcom tag format not yet supported by net/dsa/tag_brcm.c.
We also make sure that we can turn on Broadcom tags on a CPU port number
that is capable of that: 5, 7 or 8.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->cpu_port is the driver local information that should only be used
to look up register offsets for a particular port, when they differ
(e.g: IMP port override), but it should certainly not be used in place
of the DSA configured CPU port.
Since the DSA switch layer calls port_vlan_{add,del}() on the CPU port
as well, we can remove the specific setting of the CPU port within
port_vlan_{add,del}.
Fixes: ff39c2d686 ("net: dsa: b53: Add bridge support")
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Have b53_hdr_setup() check what kind of tagging protocol is configured
(Broadcom or none) and apply the correct settings in both cases.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2 and b53 replicate the same operations: clear all VLANs and set
their ports to the default VLAN tag (1 for these devices) so export the
b53 function doing just that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the comment above the chunk states, the b53 driver attempts to
disable the unused ports. But using ds->enabled_port_mask is misleading,
because this mask reports in fact the user ports.
To avoid confusion and fix this, this patch introduces an explicit
dsa_is_unused_port helper which ensures the corresponding bit is not
masked in any of the switch port masks.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure is part of DSA core data and must only be updated
by the later. It is OK and sometimes necessary for the DSA drivers to
access this data, but this has to be read only.
For that purpose, add a dsa_to_port() helper which returns a const
pointer to a dsa_port structure which must be used by DSA drivers from
now on instead of digging into ds->ports[] themselves.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each port in DSA has its own dedicated CPU port currently available in
its parent switch's ds->ports[port].cpu_dp. Use it instead of getting
the unique tree CPU port, which will be deprecated soon.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export b53_{enable,disable}_port and use these two functions in
bcm_sf2_port_setup and bcm_sf2_port_disable. The generic functions
cannot be used without wrapping because we need to manage additional
switch integration details (PHY, Broadcom tag etc.).
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2 and b53 do exactly the same thing, so share that piece.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for enabling and disabling EEE, as well as re-negotiating it in
.adjust_link() and in .port_enable().
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bcm_sf2 EEE-related functions to the b53 driver because this is shared
code amongst Gigabit capable switch, only 5325 and 5365 are too old to support
that.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for migrating the EEE code from bcm_sf2 to b53, define the full
EEE register page and offsets within that page.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to enable Broadcom tags/headers is largely switch independent,
and in preparation for enabling it for multiple devices with b53, move
the code we have in bcm_sf2.c to b53_common.c
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of repeating the same pattern: acquire mutex, read/write,
release mutex, define a macro: b53_build_op() which takes the type
(read|write), I/O size, and value (scalar or pointer). This helps with
fixing bugs that could exist (e.g: missing barrier, lock etc.).
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to configure the enabled ports once in b53_setup() and then a
second time around when dsa_switch_ops::port_enable is called, just do it when
port_enable is called which is better in terms of power consumption and
correctness.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for future changes allowing the configuring of multiple
CPU ports, make b53_enable_cpu_port() take a port argument.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not used anywhere, so remove it.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From all switchdev devices only DSA requires special FDB dump. This is due
to lack of ability for syncing the hardware learned FDBs with the bridge.
Due to this it is removed from switchdev and moved inside DSA.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before removing support for vlan dump from
DSA core. The vlans are synced with the bridge and thus there is no
need for special dump operation support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prepare phase for FDB add is unneeded because most of DSA devices
can have failures during bus transactions (SPI, I2C, etc.), thus, the
prepare phase cannot guarantee success of the commit stage.
The support for learning FDB through notification chain, which will be
introduced in the following patches, will provide the ability to notify
back the bridge about successful offload.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support FDB add/del to be on a notifier chain the slave
API need to be changed to be switchdev independent.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM53125 entry was missing an arl_entries member which would
basically prevent the ARL search from terminating properly. This switch
has 4 ARL entries, so add that.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current dsa_register_switch function takes a useless struct device
pointer argument, which always equals ds->dev.
Drivers either call it with ds->dev, or with the same device pointer
passed to dsa_switch_alloc, which ends up being assigned to ds->dev.
This patch removes the second argument of the dsa_register_switch and
_dsa_register_switch functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port net device passed to b53_fdb_copy is not used. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cygnus is a small family of SoCs, of which we currently have
devicetree for BCM11360 and BCM58300. The 11360's B53 is mostly the
same as 58xx, just requiring a tiny bit of setup that was previously
missing.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA public header includes switchdev.h, use the provided
switchdev_obj_dump_cb_t typedef for the object dump callback.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers and core use switchdev. Include switchdev.h only once, in
the dsa.h public header, so that inclusion in DSA drivers or forward
declarations of switchdev structures in not necessary anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A dsa_switch_tree instance holds a dsa_switch pointer and a port index
to identify the switch port to which the CPU is attached.
Now that the DSA layer has a dsa_port structure to hold this data, use
it to point the switch CPU port.
This patch simply substitutes s/dst->cpu_switch/dst->cpu_dp->ds/ and
s/dst->cpu_port/dst->cpu_dp->index/.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 58xx devices (Northstar Plus) do actually have their CPU port wired
at port 8, it was unfortunately set to port 5 (B53_CPU_PORT_25) which is
incorrect, since that is the second possible management port.
Fixes: 991a36bb46 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the correct software reset sequence for 58xx devices by
setting all 3 reset bits and polling for the SW_RST bit to clear itself
without a given timeout. We cannot use is58xx() here because that would
also include the 7445/7278 Starfighter 2 which have their own driver
doing the reset earlier on due to the HW specific integration.
Fixes: 991a36bb46 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Broadcom tags are not enabled in b53 (DSA_PROTO_TAG_NONE), we need
to make sure that the IMP/CPU port is included in the forwarding
decision.
Without this change, switching between non-management ports would work,
but not between management ports and non-management ports thus breaking
the default state in which DSA switch are brought up.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress or egress capture towards the capture
port. Future improvements could include leveraging the divider to allow
less frames to be captured, as well as matching specific MAC DA/SA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions for the different Roboswitch registers relevant for
ingress and egress mirroring.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.
Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.
Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.
This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate a bit of boilerplate code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the integrated switch found on BCM7278:
- core_reg_align is set to 1, to force a translation into the target
address space which is 8 bytes aligned
- an alternate SWITCH_REG layout is provided since registers are largely
bit/masks compatible but have different offsets
- conditional for all CORE_STS_OVERRIDE_{IMP,GMII_P} since those got
moved way out of the traditional register space
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have properly encapsulated and made drivers utilize exported
functions, we can switch dsa_switch_ops to be a annotated with const.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for making dsa_switch_ops const, export b53 operations
utilized by other drivers such as bcm_sf2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the two functions recently introduced: u64_to_ether() and
ether_to_u64() instead of our own versions.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have a fundamental problem in how we treat the CPU port and
its VLAN membership. As soon as a second VLAN is configured to be
untagged, the CPU automatically becomes untagged for that VLAN as well,
and yet, we don't gracefully make sure that the CPU becomes tagged in
the other VLANs it could be a member of. This results in only one VLAN
being effectively usable from the CPU's perspective.
Instead of having some pretty complex logic which tries to maintain the
CPU port's default VLAN and its untagged properties, just do something
very simple which consists in neither altering the CPU port's PVID
settings, nor its untagged settings:
- whenever a VLAN is added, the CPU is automatically a member of this
VLAN group, as a tagged member
- PVID settings for downstream ports do not alter the CPU port's PVID
since it now is part of all VLANs in the system
This means that a typical example where e.g: LAN ports are in VLAN1, and
WAN port is in VLAN2, now require having two VLAN interfaces for the
host to properly terminate and send traffic from/to.
Fixes: Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/net/dsa/b53/b53_mmap.ko | grep alias
$
After this patch:
$ modinfo drivers/net/dsa/b53/b53_mmap.ko | grep alias
alias: of:N*T*Cbrcm,bcm63xx-switchC*
alias: of:N*T*Cbrcm,bcm63xx-switch
alias: of:N*T*Cbrcm,bcm6368-switchC*
alias: of:N*T*Cbrcm,bcm6368-switch
alias: of:N*T*Cbrcm,bcm6328-switchC*
alias: of:N*T*Cbrcm,bcm6328-switch
alias: of:N*T*Cbrcm,bcm3384-switchC*
alias: of:N*T*Cbrcm,bcm3384-switch
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the fast ageing logic from b53_br_set_stp_state and implement the
new DSA switch port_fast_age operation instead.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The set_addr() callback is now optional. Remove the empty stub that b53
has.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access the priv member of the dsa_switch structure directly, instead of
having an unnecessary helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to migrate the bcm_sf2 driver over to the b53 driver for most
VLAN/FDB/bridge operations, we need to add support for the "join all
VLANs" register and behavior which allows us to make a given port join
all VLANs and avoid setting specific VLAN entries when it is leaving the
bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 58xx and 7445 chips use the Starfighter2 code, define its MIB layout
and introduce a helper function: is58xx() which checks for both of these
IDs for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a device entry for the Broadcom BCM7445 integrated switch
currently backed by bcm_sf2.c. Since this is the latest generation, it
has 4 ARL entries, 4K VLANs and uses Port 8 for the CPU/IMP port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow drivers to override specific dsa_switch_driver
callbacks, initialize ds->ops to b53_switch_ops earlier, which avoids
having to expose this structure to glue drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_switch_driver structure contains only function pointers
as it is supposed to, rename it to the more appropriate dsa_switch_ops,
uniformly to any other operations structure in the kernel.
No functional changes here, basically just the result of something like:
s/dsa_switch_driver *drv/dsa_switch_ops *ops/g
However keep the {un,}register_switch_driver functions and their
dsa_switch_drivers list as is, since they represent the -- likely to be
deprecated soon -- legacy DSA registration framework.
In the meantime, also fix the following checks from checkpatch.pl to
make it happy with this patch:
CHECK: Comparison to NULL could be written "!ops"
#403: FILE: net/dsa/dsa.c:470:
+ if (ops == NULL) {
CHECK: Comparison to NULL could be written "ds->ops->get_strings"
#773: FILE: net/dsa/slave.c:697:
+ if (ds->ops->get_strings != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_ethtool_stats"
#824: FILE: net/dsa/slave.c:785:
+ if (ds->ops->get_ethtool_stats != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_sset_count"
#835: FILE: net/dsa/slave.c:798:
+ if (ds->ops->get_sset_count != NULL)
total: 0 errors, 0 warnings, 4 checks, 784 lines checked
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers may drive different families of switches which need
different tag protocol. Rather than hard code the tag protocol in the
driver structure, have a callback for the DSA core to call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner and .bus fields since module_spi_driver() is used
which set them automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53_io_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):
drivers/net/dsa/b53/b53_common.c: In function ‘b53_arl_read’:
drivers/net/dsa/b53/b53_common.c:1072: warning: integer constant is too large for ‘long’ type
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For pdata == null the code leaves with an error.
There is no need to check the condition again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/b53/b53_srab.c: In function 'b53_srab_probe':
>> drivers/net/dsa/b53/b53_srab.c:388:20: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
pdata->chip_id = (u32)of_id->data;
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the SRAB, core driver and binding document to support the
BCM585xx/586xx/88312 integrated switch (Northstar Plus SoCs family).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Northstart Plus SoCs, we cannot detect the switch because only the
revision information is provied in the Management page, instead, rely on
Device Tree to tell us the chip id, and pass it down using the
b53_platform_data structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some configurations, gcc produces a warning for correct code
in this driver:
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read64':
drivers/net/dsa/b53/b53_mmap.c:107:10: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
^~~~~~~
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read48':
drivers/net/dsa/b53/b53_mmap.c:91:11: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
^~~~~~~
drivers/net/dsa/b53/b53_mmap.c:83:11: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 16) | lo;
I have seen the warning before and at the time thought I had fixed
it with 55e7f6abe1 ("dsa: b53: fix big-endian register access"),
however it now came back in a different randconfig build that happens
to have different inlining decisions in the compiler.
The mistake that gcc makes here is that it thinks the second call to
readl() might fail because the address 'reg + 4' is not a multiple
of four despite having knowing that 'reg' itself is a multiple of four.
By open-coding the two reads without the redundant alignment check,
we can avoid the warning and produce slightly better object code, but
get slightly longer source code instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a typo we would always be using the MIB counter width of the
first element of the counter array instead of the current element, and
we would always be accessing the register statistics with a 64-bits
read, while some could be 32-bits. This got unnoticed in testing with
MDIO and SRAB which tolerate doing this, but testing with the SPI bus
revealed bogus values being returned. Fix this by using the proper
iterator here.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53 dsa register access confusingly uses __raw register accessors
when both the CPU and the device are big-endian, but it uses little-
endian accessors when the same device is used from a little-endian
CPU, which makes no sense.
This uses normal accessors in device-endianess all the time, which
will work in all four combinations of register and CPU endianess,
and it will have the same barrier semantics in all cases.
This also seems to take care of a (false positive) warning I'm getting:
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read64':
drivers/net/dsa/b53/b53_mmap.c:109:10: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
I originally planned to submit another patch for that warning
and did this one as a preparation cleanup, but it does seem to be
sufficient by itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuration VLANs on B53 devices by implementing the
port VLAN add/del/dump functions. We currently default to a behavior
which is equivalent to having VLAN filtering turned on, where all VLANs
not programmed into the VLAN port-based vector will be discarded on
ingress.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for HW bridging by tying the ports together in the same port
VLAN mask when they belong to the same bridge, and isolating them to be
alone with the CPU port when they are not.
Propagate STP states from the bridge layer to the switch's HW mapping
when requested.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for FDB add/delete/dump using the ARL read/write logic and
the ARL search logic for faster dumps. The code is made flexible enough
it could support devices with a different register layout like BCM5325
and BCM5365 which have fewer number of entries or pack values into a
single 64 bits register.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM7445 STB chip has an issued in its revision D0 which was
previously worked around in drivers/net/dsa/bcm_sf2.c where we may
end-up double programming the integrated BCM7445 switch (bcm_sf2) and an
external Broadcom switch such as BCM53125, since these are mostly
register compatible.
Add a small quirk which just defers probing until we are sitting on the
slave DSA MDIO bus, which will allow us to intercept reads/writes and
funnel them through the SF2 internal MDIO master (which happens to
disconnect its pseudo PHY).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.
This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).
Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
