Disabling FEC for specific monitors is sometimes required for debugging
while in the monitor bringup phase
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We see an issue that caused clk_optimized_required to be set true in
certain cases, causing passive flips to fail. This is because of a typo
where wm_optimized_required was set twice.
[HOW]
Set clk_optimized_required to false after updating clocks.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vstartup calculation is incorrect due to use 2 number of cursors and
result in an underflow when playing video in full screen mode and
combines graphic plane and video plane.
[How]
Apply new policy for dml calculation.
1 cursor for graphic plane, 0 cursor for video plane.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Freesync borderless is not meant to be enabled on any APUs
[HOW]
Add is_apu cap to dcn21_resource_construct for correct recognition
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SMU FW previously had an issue with lowering display clock to below 100
MHz, and a workaround was put in to limit it. Newest SMU FW does not
have this issue, and no longer needs the 100MHz cap.
[HOW]
Remove the 100MHz cap based on the SMU FW version.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When transitioning from SST to MST, the HDCP repeater in some MST
displays will enter a bad state. The HDCP repeater is recovered after
failing and performing authentication again.
[How]
Add monitor patch to trigger HDCP authentication failure after
encryption is enabled and re-authenticate.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When combining two or more pipes in DSC mode, there will always be more
than 1 slice per line. In this case, as per DSC rules, the sink device
is expecting that the ICH is reset at the end of each slice line (i.e.
ICH_RESET_AT_END_OF_LINE must be configured based on the number of
slices at the output of ODM). It is recommended that software set
ICH_RESET_AT_END_OF_LINE = 0xF for each DSC in the ODM combine. However
the current code only set ICH_RESET_AT_END_OF_LINE = 0xF when number of
slice per DSC engine is greater than 1 instead of number of slice per
output after ODM combine.
[how]
Add is_odm in dsc config. Set ICH_RESET_AT_END_OF_LINE = 0xF if either
is_odm or number of slice per DSC engine is greater than 1.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When test pattern is enabled with ODM combine, test pattern is generated
by piecing multiple DPGs image together. The current code will program
all DPGs with horizontal offset of 0. This will cause all DPGs to output
the beginning of the pattern. Instead each DPG should program a
horizontal offset of its x position to form a continous pattern when
pieced together.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Allow vsc info packet if vsc is supported. Update vsc based on test
pattern request. Remove dpg_is_blanked polling, apply hardware global
lock instead to ensure double buffered dpg is updated with vsc in one
frame
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Typo in amdgpu_dm error message:
"Failed to found connector for link!"
[How]
1. Replace with:
"Failed to find connector for link!"
2. Fix indentation checkpatch warnings.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
In order to correctly intepret clock table, num_states is also needed.
This field did not get moved with clock_table but should next to it for
easier access/viewing.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we have single channel memory, we can not light up 2 4k displays
with a 1080p edp, because we don't have enough bw by a small margin.
this small margin comes from dcc meta being too large. We however don't
have this dcc meta when we create fake planes so, before the flip we
will not filter out the mode for 2 4k displays with a 1080p edp
[how]
Change get_default_swizzle_mode to something more general so we don't
end up with a separate function for every missing field in the fake
plane. Add a reasonable dcc meta to the fake plane when it is filled in,
so we filter out modes that don't have enough bandwidth. To do this, we
take the screen width and align it to 1024(8k 60)
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some asics don't support FEC but FEC overhead is added into link
bandwidth calculation by mistake. This causes certain timing cannot be
validated.
[how]
Only include FEC overhead if both asic and display support FEC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Move psr_on_dmub flag from dc_debug_options to dc_config.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reset connection is called before remove display in mod_hdcp. When
remove display is called, the display structure has been zeroed from
reset connection. Since no displays can be found, remove display does
not properly reset the hardware. This causes validation errors when
another display is plugged into a different port afterwards.
[How]
Moved displays structure out of connections structure. Displays
structure is now directly within mod_hdcp. Displays is no longer zeroed
when reset connection is called.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern we mistook dp_hw_link_settings
for a redundant call of dpcd_set_link_settings
[How]
revert the changes to dpcd_set_link_settings calls for this workaround.
Do not need to revert the entire change since it only affects patched
case
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: David Galiffi <David.Galiffi@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues on detect_dp function as suggested by
checkpatch.pl.
CHECK: Lines should not end with a '('
WARNING: Missing a blank line after declarations
WARNING: line over 80 characters
CHECK: Alignment should match open parenthesis
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Coding style clean up on enable_link_dp function as suggested by
checkpatch.pl:
CHECK: Lines should not end with a '('
WARNING: line over 80 characters
WARNING: suspect code indent for conditional statements (8, 24)
CHECK: braces {} should be used on all arms of this statement
ERROR: else should follow close brace '}'
CHECK: Comparison to NULL could be written
"link->preferred_training_settings.fec_enable"
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is freeing the wrong variable so it will crash. It should be
freeing "*dmub" instead of "dmub".
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are multiple statements that are indented incorrectly. Add
in the missing tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nothing else calls it. Not sure it's necessary.
v2: remove unused port variable.
Reviewed-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Split into init and register functions to avoid a segfault
in some configs when the load/unload callbacks are removed.
v2:
- add back accidently dropped has_aux setting
- set dev in late_register
v3:
- fix dp cec ordering
v4:
- squash in kdev reference fix
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To handle debugfs setup on non DP MST connectors.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Into the function that creates the debugfs files rather
than setting them explicitly in the callers.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for display.
v2: add config guard for DC
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com> (v1)
Acked-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The core does this for us now.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the existence of the workqueue itself to determine when to
enable HDCP features rather than sprinkling asic checks all over
the code. Also add a check for the existence of the hdcp
workqueue in the irq handling on the off chance we get and HPD
RX interrupt with the CP bit set. This avoids a crash if
the driver doesn't support HDCP for a particular asic.
Fixes: 96a3b32e67 ("drm/amd/display: only enable HDCP for DCN+")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206519
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:
In function hubp21_set_vm_system_aperture_settings:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:343:23:
warning: variable mc_vm_apt_default set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when changing display clock, SMU need to use power up DFS and use
DENTIST to ramp DFS DID to switch target frequency before switching back
to bypass.
[How]
fixed the minimum display clock to 100MHz, it's W/A the same with PCO.
Signed-off-by: Yu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System will crash when trying to access local sink in
core_link_enable_stream in MST case.
[How]
Access patches directly from stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow sometimes occurs during transition into MPO with stutter
enabled.
[How]
When transitioning into MPO, disable stutter. Re-enable stutter within
one frame.
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently clock table struct is very far down in the bounding box struct
making it hard to find while debugging, especially when using the
dal3dbgext.
[HOW]
Move it up so it is the first struct defined, and therefore much easier
to find and access.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some display configuration like 1080P monitor playing a 1080P video,
if user use ALT+F4 to exit Movie and TV, there is a chance clocks are
same only water mark changed. Current clock optimization machanism will
result in water mark keeps high after exit Movie and TV app.
[How]
Return if watermark need to be optimized when doing program watermark,
perform the optimization after.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to assign surface size rather than viewport size for surface size
dml variable.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update TTU properly if DRAMClockChangeWatermark changes. If
TTU < DRAMClockChangeWatermark, we pstate won't be allowed and we will
hang in some PSR cases.
[How]
Update TTU if DramClockChangeWatermark value increases (only if TTU was
dependent on the watermark value on the DRAMClockChangeWatermark value
in the first place).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
RV2 and variants are indistinguishable by hw internal rev alone, need to
be distinguishable in order to correctly set max vlevel. Previous
detection change incorrectly checked for hw internal rev.
[HOW]
Use pci revision to check if RV2 or low power variant Correct a few
overlapping ASICREV range checks
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Add infrastructure to enable and disable PSR on DMCUB.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dcn20_populate_dml_pipes_from_context to correctly handle odm
when no surface is provided.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DalMPVisualConfirm does not support FreeSync 2 ARGB2101010 which causes
black visual confirm bar when playing HDR video on FreeSync 2 display in
full screen mode
[How]
Added pink color for DalMPVisualConfirm on FreeSync 2 ARGB2101010
surface
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern was link level but the whole
asic should be affected.
[How]
- change old link flag to dc level
- new bit in dc->work_arounds set by DM
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some displays clear ignore MSA bit on mode change, which cause
blackscreen when programming variable vtotals. Ignore MSA bit needs
programming needs to be delayed or re-set to be retained.
[How]
Create patch to delay programming ignore MSA bit after unblanking
stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A software workaround is required for all vendor-built cards on platform.
[How]
When performing DP link training, we must send TPS1 before DPCD:100h is
written with the proper bit rate value. This change must be applies in
ALL cases when LT happens.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Not programming dto with same values causes test failures in DCN2 diags
DPP tests.
[HOW]
This reverts commit 1b53e73323.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Firmware state helps to debug sequence issues and hangs for DMCUB
commands and we don't have an easy mechanism to dump it from the driver.
[How]
Add a debugfs entry to dump the current firmware state.
Example usage:
cat /sys/kernel/debug/dri/0/amdgpu_dm_dmub_fw_state
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently DAL programs negative slope for the last point of output
transfer function curve.
[How]
Applying a check for the last PWL point for RGB values not to be
smaller than previous. If smaller, initialize the last point values
to a sum of previous PWL value and previous PWL delta;
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some structures and functions meant only to be used in the
scope of that single rn_clk_mgr c file.
[How]
Make structs and funcs static if only meant to be used within
rn_clk_mgr
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make panel backlight and power on/off functions into
hardware specific function pointers
[How]
Add function pointers for panel related hw functions
- is_panel_powered_on
- is_panel_backlight_on
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when the rxstatus split was done the index was incorrect. This
lead to HDMI repeater authentication failure for HDCP2.X So fix it
Fixes: 3021690037 ("drm/amd/display: split rxstatus for hdmi and dp")
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When calculating nominal refresh rates, don't round.
Only the VSIF needs to be rounded.
[How]
Revert rounding change for nominal and just round when forming the
FreeSync VSIF.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unused VMIDs were not evicted correctly
[How]
1. evict_vmids() logic was fixed;
2. Added boundary check for add_ptb_to_table() and
clear_entry_from_vmid_table() to avoid crash caused by array out of
boundary;
3. For mod_vmid_get_for_ptb(), vimd is changed from unsigned to signed
due to vimd is signed.
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Add optimization to allow pstate change support when all displays
are off in DCN2.
[How]
Add clk_mgr_helper_get_active_plane_cnt() to sum plane_count for all
valid stream_status[]. If plane_count is 0, then there are no active
or virtual streams present. Use plane_count == 0 as extra condition to
enable p_state_change_support in dcn2_update_clocks().
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need DMCU for features like PSR and ABM.
[How]
Add path to dmcu firmware binary and load it for Navi12.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we're doing backdoor load then do it entirely ourselves without
invoking any of the frontdoor path to avoid potential issues with
outdated tOS.
[How]
Check the load type and don't pass it to base if we don't want it
loaded.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we execute the first command for ASIC_INIT for command table
offloading we can hit a timing scenario such that the interrupts
for the inbox wptr haven't been enabled yet and the first command
is ignored until the second command is sent.
[How]
This happens when either the SCRATCH0 is already the correct status
code or autoload check is unsupported.
Clear SCRATCH0 during reset.
Also ensure that we don't accidentally reset the ASIC again in case
of a hang by clearing GPINT while we're at it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
According to HW team, PG is dropped for NV12, but programming
the registers will still cause power to be consumed, so don't
program for NV12.
[How]
Set function pointer to NULL if NV12
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bugs occur when TX interrupt comes in when no USB-C on board.
[How]
Check PHY for USB-C before enabling TX interrupt in DMCU FW.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently there is a minor error in scaling filter coefficients
caused by truncation to fit the HW registers.This error accummulates
with increased taps, but has gone unnoticed due to vast majority of
scaling being done with only 4 taps.
Scaling filters are now updated using HW team's filter generator
which has quantization error minimization built in.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since the i2c payload allocation can fail need to check return codes
[How]
Clean up i2c payload allocations and check for errors
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
core_link_read_dpcd() will invoke dm_helpers_dp_read_dpcd(),
which needs to read dpcd info with the help of aconnector.
If aconnector (dc->links[i]->prev) is NULL, then dpcd status
cannot be read.
As a result, dpcd read fails and a line of error will be
printed out in dmesg.log as:
"*ERROR* Failed to found connector for link!"
[How]
Make sure that aconnector (dc->links[i]->prev) is not NULL,
then read dpcd status.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Joseph Gravenor <Joseph.Gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the existence of the workqueue itself to determine when to
enable HDCP features rather than sprinkling asic checks all over
the code. Also add a check for the existence of the hdcp
workqueue in the irq handling on the off chance we get and HPD
RX interrupt with the CP bit set. This avoids a crash if
the driver doesn't support HDCP for a particular asic.
Fixes: 96a3b32e67 ("drm/amd/display: only enable HDCP for DCN+")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206519
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:980:36:
warning: address of 'sink->edid_caps.panel_patch.skip_scdc_overwrite'
will always evaluate to 'true' [-Wpointer-bool-conversion]
if (&sink->edid_caps.panel_patch.skip_scdc_overwrite)
~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
1 warning generated.
This is probably not what was intended so remove the address of
operator, which matches how skip_scdc_overwrite is handled in the rest
of the driver.
While we're here, drop an extra newline after this if block.
Fixes: a760fc1bff ("drm/amd/display: add monitor patch to disable SCDC read/write")
Link: https://github.com/ClangBuiltLinux/linux/issues/879
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5JsVQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGHZEH+wddtJO4dZk5TZdF
KZB2w2ldsCvrBZAmas1TVvm8ncvUf+ATUZcSIzvZ3YbLmxsuLF2Cz3kD+n+36Mvy
ejwq8Scl7jwnouYps/Gfd6rRj/uCafqST4qp15GMGeiy2ST4A8dJrv5IAgZhD8/N
SN1bSr1AXpZ2JlEzzLDQ/NdVoNMS6IzCOsaINZcc60/XQoQZFRBWamMJFqu+CmXD
SBJOybQNFJhziy45cGZSAl+67sSCcoPftwTs0Stu4CJsvFWRb3MsbNTDS51Hjcc4
3tdgGOhoNXzyzZr96MEAHmiaW4VLQv0PGgUfOajE35viMz48OrwCTru8Kbuae3XM
YHV4qJk=
=yiem
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXkpecgAKCRDj7w1vZxhR
xU4CAQD/8ZzfYroiiEI7FHEgvnuldGYZqA9kbNAO2Vueeac0OgD+Jojewdxy+pJ9
dxfA/POdtzx3hOdN+U1YgaDC0hbXwww=
=XgKq
-----END PGP SIGNATURE-----
Merge v5.6-rc2 into drm-misc-next
Lyude needs some patches in 5.6-rc2 and we didn't bring drm-misc-next
forward yet, so it looks like a good occasion.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We were using incorrect byte order after we started using the drm_defines
So fix it.
Fixes: 02837a91ae ("drm/amd/display: add and use defines from drm_hdcp.h")
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VBLANK callbacks in struct drm_driver are deprecated in favor of
their equivalents in struct drm_crtc_funcs. Convert amdgpu over.
v2:
* don't wrap existing functions; change signature instead
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123135943.24140-6-tzimmermann@suse.de
The callback struct drm_driver.get_scanout_position() is deprecated in
favor of struct drm_crtc_helper_funcs.get_scanout_position(). Convert
amdgpu over.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123135943.24140-5-tzimmermann@suse.de
It's used by more than just DCN2.0. Fixes missing symbol when
amdgpu is built without DCN support.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to cover dcn2.x related headers.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-msg_in is not needed for enabling encryption.
-Use hdcp2_set_encryption instead of hdcp1_enable_encryption for hdcp2.2
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We were using incorrect byte order after we started using the drm_defines
So fix it.
Fixes: 02837a91ae ("drm/amd/display: add and use defines from drm_hdcp.h")
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HDCP DTM needs to be aware of the upto date display topology
information in order to validate hardware consistency.
[how]
update HDCP DTM on update_stream_config call.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
According to the specs when bksv or ksv list fails SRM check,
HDCP TX should abort hdcp immediately.
However with the current code HDCP will be reattampt upto 4 times.
[how]
Add the logic that stop HDCP retry if bksv or ksv list
is revoked.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSP added a new return code for revoked receivers (SRM). We need to
handle that so we don't retry hdcp
This is already being handled on windows
[How]
Add the enums to psp interface header and handle them.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver crash with psr feature enabled due to divide-by-zero error.
This is a regression after rework to calculate static screen frame
number entry time.
[How]
Correct order of operations to avoid divide-by-zero.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:
In function dcn10_post_unlock_program_front_end:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2623:29:
warning: variable stream_status set but not used [-Wunused-but-set-variable]
commit bbf5f6c3f8 ("drm/amd/display: Split program front end part that occur outside lock")
involved this unused variable.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the case where we do have these passed in then we should be using
these instead of the registers - those are only programmed when booting
the adapter as primary.
[How]
Check if fb_base/fb_offset are non-zero. The value of 0 is invalid
for fb_base but is valid for fb_offset on dGPU.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver needs to know PSR state.
[How]
Use GPINT to call to firmware and get psr state.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
customer issue: found that for their specific panel, EDID register space
being overwritten during SCDC read write
[how]
customer accepted HDMI 2 features not working - disabled SCDC read/write
as well as HDMI 2 in general based on monitor patch
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm scaling calculations are only done when adding initial
odm pipe. Any scaling re-calculations will mess up odm because of this.
This change resolves the problem by updating scaling split logic to
handle odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the struct dc_panel_patch, we have a field named
manage_secondary_link which is not used by any part of the code. This
commit drops the unused field.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some register defines are redundant or updated
[How]
Update register defines
Remove some redundant defines
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Sun peng Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
in dcn10_apply_ctx_for_surface(), if we hit !top_pipe_to_program,
pipe_ctx->update_flags could not get cleared.
[How]
Moved clearing pipe_ctx->update_flags logic before if
(!top_pipe_to_program) to gurantee pipe_ctx->update_flags get cleared.
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Several modern displays support HDR/OLED panel, and one of the
interesting changes provided by this technology is the new approach for
handling backlight. More precisely, in the traditional way, we use PWM
to manage display backlight; however, with HDR/OLED we begin to use DP
Aux channel for adjusting the backlight.
This patch, enable the backlight control in HDR/OLED display via DP Aux.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Set version is currently not called.
[How]
Add call to set version from copy settings. This
should be the only time this is called as the eDP
caps should never change.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Vendor dongle requires propietary OUI and handshake sequence.
[HOW]
Add a new structure to dc_init_data, to allow creator to pass
an override vendor_oui. This value will be written to DP_SOURCE_OUI
instead of AMD signature, when dpcd_set_source_specific_data is
called.
Signed-off-by: Calvin Hou <Calvin.Hou@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With the fallback case in place for command table offloading via DMCUB
it's no longer an error for the command table to be missing specific
entries.
[How]
Drop the BREAK_TO_DEBUGGER();
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
before we exit early in edp_reciever_ready if we detect that panel
is not edp or below rev 1.2. This will skip the backlight/t7 delay panel
patch.
[how]
edit logic to ensure panel patch is applied regardless of edp rev.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, gcc spews a warning as:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hubbub.c: In function ‘hubbub1_verify_allow_pstate_change_high’:
./include/drm/drm_print.h:316:2: warning: ‘debug_data’ may be used uninitialized in this function [-Wmaybe-uninitialized]
This is because the code checks against a static value although it's
basically a constant and guaranteed to be set.
This patch changes the type prefix from static to const for addressing
the compile warning above and also for letting the compiler optimize
better.
Fixes: 62d591a8e0 ("drm/amd/display: create new files for hubbub functions")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
not turning off the mst hub before detection on reboot
causes us to not be able to light up displays with mst hook
[how]
on hw init, see if any displays are lit up. if so, turn them off
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
these registers should have been double buffered. SW workaround we will have SW program the more aggressive (lower) values
whenever we are upating this register, so we will not have underflow at expense of less optimzal request pattern.
[How]
there is a driver bug where we don't check for 0, which is uninitialzed HW default. since 0 is smaller than any value we need to program,
driver end up with not programming these registers
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] old panel has been enabled for window driver but not linux.
[How] enable oled panel support for linux. this patch is dc part.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DMUB tracebuffer is useful for understanding DMCUB execution state.
[How]
Add a "show" attribute debugfs so we can loop through the buffer
and print the entries.
The structs for the entry format are defined in the debugfs since
the tracebuffer header no longer exists in the DMUB service.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
enum dc_log_type has more than 32 entries. User cannot set larger entries,
like LOG_DSC. Logs from LOG_GAMMA_DEBUG where being printed even though
flag was not enabled, because dal_logger_should_log check erroneously
passed.
[HOW]
Change struct dal_logger.mask and struct dc_init_data.mask to uint64_t.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Having watermark ranges saved inside clk_mgr to be
available for debug at all times would be useful.
Add it to the clk_mgr_internal struct for reference.
Only populated for Renoir, unused for other asics.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
hyperV flag should be passed from dm to DC, and override the
nv12 flip workaround flag.
[How]
Add flag to phy address config struct and pass the value in dm.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous logic is only good for 15W parts. Other configuration
need a smarter logic to match clk levels with pp table in the fuse.
[How]
Cache all 8 DPM level's clock data, find lvl that match each pstate
in the pp table and build input into DML base on that
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
hwss should not guess what type of pipe lock is needed.
The caller of the lock function should know
the right type of pipe lock.
Decouple the setup of global lock outside of pipe control lock
logic.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
new HW engine mapping requirment use in PSP
[how]
report stream_enc_inst
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The break in apply_ctx_interdependent_lock() may potentially
lead to early break from the loop leaving update plane unlocked
[How]
Remove break
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
int i can go out of boundary which will cause crash
[How]
Fixed the maximum value of i to avoid i going out of boundary
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After locking refactor GSL is not acquired properly
resulting in immediate flip issues.
[How]
Do not copy old GSL state anymore since GSL is acquired
earlier now.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Screen flickering when HDR switches between FP16 and ARGB2101010
[How]
Moved pipe_control_lock so stream update and plane update occur atomically
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DMCUB may be currently executing commands when the reset is
triggered.
Before issuing a reset we should first wait for the DMCUB to finish
its work.
[How]
Send the GPINT command for halting the firmware before reset.
Get the ack for the command then wait for the scratch register to
become the correct value.
We want this to take under ~40us or so at most before we force reset
to cover PHY delay sequence max time.
Each register read will be at least ~1-3us so don't bother using udelay.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The General Purpose Interrupt is used on the DMCUB to pass lightweight
commands via a register to the DMCUB.
This is limited to 32-bit command and 32-bit response.
This will be used for shutting down the firmware in a clean manner.
[How]
Add the command IDs and the data register to correctly format
the commands.
Add the interface functions to dmub_srv for sending and receiving the
commands.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Diagnostics team reported various issues found when enabling warnings as errors
[How]
Fix implicit conversions
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC updates only set type to FULL UPDATE, but doesn't
flag the change
[How]
Add DSC flag update flag
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Eventually want to lock at a higher level in stack.
To do this, we need to be able to isolate the parts that need to be done
after pipe unlock.
[How]
Split out programming that is done post unlock.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver crash with psr feature enabled due to divide-by-zero error.
This is a regression after rework to calculate static screen frame
number entry time.
[How]
Correct order of operations to avoid divide-by-zero.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why/how]
We found out that the register we read actually gets reset by SMU
after we loose power, meaning this always returns true
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The call to dp_enable_link_phy are using default/invalid values for clock id
and link settings.
[How]
Move workaround code to after its parameter variables are determined.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Must know psr version during runtime.
[How]
Add set psr version message structures.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Call the cmd ids for set/get srm according to the sysfs call
v2: Use define for the magic number
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
we need to load SRM before we start HDCP. Because for S3 case the sysfs call will be
after we have already enabled HDCP, so we might not be using the latest SRM
[How]
Set srm before starting HDCP.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSP doesn't have the ability to store SRM in a non-volatile memory. And since
the kernel cannot write to the storage directly, we need usermode to facilitate
this
As per spec the SRM needs to be persistent so this interface is to be
called by the usermode anytime the system goes down/powers on
*boot/resume: load from storage
*shutdown/suspend: save to storage
[How]
Provide a sysfs interface so that the usermode can set/get srm at the right times
save to storage: call "cat /sys/class/drm/card0/device/hdcp_srm > file" after boot and resume
-driver calls psp_get_srm() to get the stored srm and outputs it
load from storage: call "cat file > /sys/class/drm/card0/device/hdcp_srm" before shutdown and suspend
-driver reads the file from sysfs and calls psp_set_srm() to send the SRM to PSP
v2:
-update commit description
-add comment about sysfs file handling in the code
v3:
- squash in use after free fix (Dan Carpenter)
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to support SRM(System Renewability Message)
As per hdcp spec (5.Renewability) SRM needs to be storage in a non-volatile
memory.
PSP owns the checking of SRM but doesn't have the ability to store it in a
non-volatile memory. So we need the kernel driver to facilitate it using the
interface provided by PSP
[How]
Add the interface to the header file, so the driver can use them
v2: update commit description
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need this to create sysfs (followup patch)
[How]
Change the parameter
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We might get different numbers of clocks from powerplay depending
on what the OEM has populated.
v2: add assert for at least one level
Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we disable a connector we don't explicitly remove it from the module so the
display is still cached(SW) in the hdcp_module.
SST: no issues because we can only have 1 display per link
MST: We have x displays per link, now if we disable 1 we don't remove it from the
module so the module has x display cached(SW).
If we try to enable HDCP, psp verification will fail because we are reporting x
displays while the HW only has x-1 display enabled
[How]
Check the callback for when we disable stream and call remove display.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Remove a backslash symbol accidentally left in increase bpp function
when computing mst dsc configuration.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In current code we're essentially drawing the cursor on every pipe
that contains it. This only works when the planes have the same
scaling for src to dest rect, otherwise we'll get "double cursor" where
one cursor is incorrectly filtered and offset from the real position.
[How]
Without dedicated cursor planes on DCN we require at least one pipe
that matches the scaling of the current timing.
This is an optimization and workaround for the most common case where
the top-most plane is not scaled but the bottom-most plane is scaled.
Whenever a pipe has a parent pipe in the blending tree whose recout
fully contains the current pipe we can disable the pipe.
This only applies when the pipe is actually visible of course.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to do atomic check first, then validate global state.
If not, when connecting both MST and HDMI displays and
set a bad mode via xrandr, system will hang.
[How]
Move drm_dp_mst_atomic_check() to the front of
dc_validate_global_state().
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake on the struct field name link_integiry_check,
fix this by renaming it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A for-loop is iterating from 0 up to 1000 however the loop variable count
is a u8 and hence not large enough. Fix this by making count an int.
Also remove the redundant initialization of count since this is never used
and add { } on the loop statement make the loop block clearer.
v2: drop useless else (Walter Harms)
Addresses-Coverity: ("Operands don't affect result")
Fixes: ed581a0ace ("drm/amd/display: wait for update when setting dpg test pattern")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allocation isn't required and can fail when resuming from suspend.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1009
Signed-off-by: Dor Askayo <dor.askayo@gmail.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 80adaebd2d.
[WHY]
This change was working around a regression that occured in this:
commit 0301ccbaf6 ("drm/amd/display: DP Compliance 400.1.1 failure")
With the fix to run verify_link_cap when the SINK_COUNT of
dongles becomes non-zero this change is no longer needed.
Cc: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Two years ago the patch referenced by the Fixes tag stopped running
dp_verify_link_cap_with_retries during DP detection when the reason
for the detection was a short-pulse interrupt. This effectively meant
that we were no longer doing the verify_link_cap training on active
dongles when their SINK_COUNT changed from 0 to 1.
A year ago this was partly remedied with:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
This made sure that we trained the dongle on initial hotplug (without
connected downstream devices).
This is all fine and dandy if it weren't for the fact that there are
some dongles on the market that don't like link training when SINK_COUNT
is 0 These dongles will in fact indicate a SINK_COUNT of 0 immediately
after hotplug, even when a downstream device is connected, and then
trigger a shortpulse interrupt indicating a SINK_COUNT change to 1.
In order to play nicely we will need our policy to not link train an
active DP dongle when SINK_COUNT is 0 but ensure we train it when the
SINK_COUNT changes to 1.
[HOW]
Call dp_verify_link_cap_with_retries on detection even when the detection
is triggered from a short pulse interrupt.
With this change we can also revert this commit which we'll do in a separate
follow-up change:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
Fixes: 0301ccbaf6 ("drm/amd/display: DP Compliance 400.1.1 failure")
Suggested-by: Louis Li <Ching-shih.Li@amd.com>
Tested-by: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
FMT has limitation to support YCbCr420 with h_active greater than 4096.
[how]
Use odm combine to overcome the limitation.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver didn't init hw i2c speed cause hdcp hw cannot
send command, because the default value of speed register
is 0x2.
[How]
Restore the default speed when release i2c engine
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MPO isn't enabled on some 4k videos due to video source width is 4096
and the current limit is 3840.
[How]
Changed the limit to 4096.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
MSA will be deprecated in the future.
Need to support VSC during DP test automation.
[how]
Do not disable VSC during DP test automation.
TODO - need to add VSC update on DM side on test request.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
CW2 may already be programmed when coming back from S4. In this case
we want to unconditionally replace whatever DMCUB version is currently
enabled with the latest.
[How]
Check the hw_init flag to know whether or not we've previously executed
the initliazed routine.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These logically make sense more to be set after the DMCUB has been
reset rather than when we setup the inbox.
[How]
Move them into the reset callback.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCUB command table doesn't support ATOM_ENABLE/ATOM_DISABLE anymore
so we never end up calling the DCN init path in DMCUB.
[How]
Map ATOM_ENABLE to ATOM_INIT only for DMCUB command table offloading.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We'll need this to perform a clean shutdown before unloading the driver.
[How]
It will call reset internally and set hw_init to false. It won't do
anything if the hardware isn't initialized.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
determine_update_type_for_commit() uses pointers to single instance
of local variable to fill scaling/color info for all planes updates.
This is a bug, that leads to incorrect update type for commit in case
of multiple planes per crtc.
Each plane should refer to separate scaling/color data.
[How]
Use arrays for plane properties.
Bundle all properties into a single structure to simplify memory allocation.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoded fixed values are not proper.
[How]
Use enum values instead of fixed numbers.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In HG mode, vbios didn't call DispController_Init to program NV1x
XTAL_REF_DIV value when ASIC_INIT, but driver read XTAL_REF_DIV
to calculate i2c reference frequency. it cause i2c frequency change
from 100kHz to 200kHz.
[How]
remove get_speed function and calculate reference frequency at
set_speed functiton.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It has duplicate code for building regamma curve
[How]
Remove the duplicate code and use the same function for building regamma
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The types for dummyinteger1 and dummyinteger2 are unsigned
as part of the DML spec. They should not be long.
[How]
Make them unsigned int instead of long.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DMCUB enabled hardware DC has a dependency on DMCUB already being
running.
Command table offloading will fail on first modeset if DMCUB isn't
initialized first.
[How]
Perform DMCUB hardware initialization before DC.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver use pipe_ctx to reallocate payload may cause allocate
payload twice on same sink with split pipe.
[How]
Drvier must to check pipe_ctx is split pipe or not to avoid
reallocate payload twice on same sink.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the command table isn't available then we can fallback to DMCUB
offloading if it's enabled and available.
[How]
Instead of assigning NULL for supported command table functions we can
fallback to the DMCUB when it's available.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Under some hardware initialization sequences the fb base/fb offset
provided can be zero or hardwareinit can happen too late.
We want to ensure that we always have the correct fb_base/fb_offset
when performing DMCUB hardware initialization so we can do DMCUB
command table offloading during first dc hardware init.
[How]
Read from the DCN registers. VBIOS already filled these in for us.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Empty dsc enc caps when debug option is set to disable DSC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DP 1.4a Spec requires that training pattern only under certain
specific conditions. Currently driver will re-send
training pattern every time voltage swing value changes,
but that should not be the case.
[How]
Do not re-send training pattern every time VS values
are different. Only send it on the first iteration.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On video test pattern request we need to update MSA and VSC so
it will match the requested test pattern dynamic range field.
[how]
Update dynamic range field in MSA and disable VSC as updating VSC
info packet is complicated and not required for test pattern purpose.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DPG is used to generate both blank and test automation test pattern.
When test automation is running the requested test pattern can be
overriden by the blank or unblank call because it is using the same
hardware.
[how]
When test pattern is requested, skip blank or unblank.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Try to allocate MST payload but receive HPD short pulse with link loss
casue driver allocate payload twice. It cause monitor can't light up
successfully.
[How]
When driver receive HPD short pulse with link loss, we need to
deallocate payload then allocate payload.
Then we will not allocate payload twice with same sink.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to fix DML portability issues to enable SW unit testing around DML
[how]
Move calcs into dc include folder since multiple components reference it
Remove relative paths to external dependencies
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The rapid msleep operation causes the white line garbage when
DAL check flip pending status in SetVidPnSourceVisibility.
To execute this msleep will induce context switch, and longer
delay could cause worse garbage situation.
[how]
To replace msleep with mdelay.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only need to do surface flip for video plane via dmcub.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently if seamless boot is enabled, we will skip double buffer enable
for OTG_BLANK. However, we need the double buffer enable in order to
block global sync signals when OTG becomes blanked (for PSR). Blocking
global sync signals prevent pipe from requesting data.
[How]
Move tg_init before seamless boot check.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dpcd cap mismatch in 2200 vs base
[How]
Add monitor patch which using based caps to overwrite 2200
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently we wait for test pattern after each pipe is programmed. For
ODM combined scenario it will cause test pattern is shown on only half
screen for 1 frame. This is not desirable.
[how]
No wait between odm pipe programming, only wait after all pipes are
programmed.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With different refresh rate panels, the PSR entry/exit time is
different since it is dependent on 2 frame entry time today
[How]
Make static screen num frame entry time to be calculated
such that entry time is within 30 ms instead of fixed num
frames.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCU need to wait a vblank to handle psr enter command. When psr exit
coming before vblank, the psr exit command will be skip because current
psr state is disable.
[How]
remove psr state condition when psr exit case
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IRAM definition needed for versions of DMCU containing ABM 2.4
[How]
Pass ABM 2.3 IRAM definition, which is compatible with ABM 2.4, to DMCU
when ABM 2.4 FW is detected
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML Initialization was previously done on dcn21_resource initialization.
This meant that DML soc struct was populated with hardcoded values.
[How]
Move DML initialization to after updating bounding box, to use clock table
values from SMU.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PHY will sometimes be in bad state on hotplugging display from USB-C
dongle.
[How]
Add additional calls to disable and then enable PHY before link training
starts during verify_link_cap.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DMUB PSR command IDs do not have the correct values.
[How]
Fix the command IDs and cleanup the formatting.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rework surface programming for RN to separate preparing parameters and
register programming.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recent double buffering changes for dcn2 use IX_REG_READ.
However, this macro returns the full register value, with the need to
manually shift and mask it to retrieve field data.
[How]
Create new IX_REG_GET macro that handles shift and mask.
Use this for double buffering reads instead of IX_REG_READ.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Moving PSR from DMCU to DMCUB.
[How]
Cleanup psr spec files and add PSR hw programming files.
No functionality is included in this change.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Programming surface flip addresses via dmcub uC for optimizing the data
flush.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting color temperature, screen tearing was observed.
This was due to overwritten values in gamut remap registers.
This issue was solved for OCSC and ICSC by alternating between "A" and
"B" registers to double buffer the writes.
[How]
Create new set_gamut_remap and program_gamut_remap for dcn20.
Alternate which registers are written to by switching modes each time.
Also fixes ICSC mode reg read to use proper data offset.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Moving PSR from DMCU to DMCUB.
[How]
Add driverside PSR changes required to send inbox messages to fw.
These changes are non-functional until the psr structure allocation
is uncommented.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting video brightness, screen tearing was observed.
This was due to overwritten values in ICSC registers. In dcn10, this issue had been
fixed by implementing double buffering via alternating ICSC modes.
However, the second register set used in dcn1 doesn't exist in dcn2.
[How]
Create new program_input_csc for dcn20.
Use ICSC_B registers instead of COMA registers as second set.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add more fields to support upcoming dml versions
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Don't want to start HW discovery unless we have lost power,
as doing rediscovery otherwise is both unnecessary and time consuming.
Before this change it takes 40 seconds to go in to suspend, after it
takes 27 seconds
[How]
Accelerated mode gets cleared if we lose power. Only do detection if
this register is cleared
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Test pattern should be applied to hardware when exiting set test pattern
function.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
48mhz turn off feature does not work on HDMI and DVI, but the feauture
was only blocked on HDMI, this change will apply the same wa on DVI
[HOW]
Apply workaround for all TMDS signal types (HDMI, DVI single/dual link)
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If dummy pstate latency is 0 we should report the actual
pstate support, and not that pstate is always supported.
[How]
Don't always program pstate support true
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure that lttpr_caps has the mode set to repeater.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting colour properties (e.g. brightness), screen tearing was observed.
This was due to overwritten values in OCSC registers. In dcn10, this issue had been fixed by
implementing double buffering by alternating OCSC modes.
[How]
Alternate which OCSC registers are used by switching modes each time.
This double buffers the CSC writes.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to ensure that the DMUIF in MMHUBBUB is also in reset so we
aren't generating requests while the DMCUB is in reset.
[How]
Set DMUIF_SOFT_RESET=1 on reset and DMUIF_SOFT_RESET=0 on reset
release.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The inst firmware isn't necessarily fully flushed to framebuffer
memory and the DMCUB can hang due to invalid inst being parsed.
[How]
Like the fix to flush ringbuffer commands before updating the inbox
write pointer we need to read back inst memory before writing the
CW0 registers.
Add a helper to read 64-byte chunks to avoid a large temporary buffer.
Read the remaining leftover bytes if the inst_fb isn't fully aligned.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There's a data race that can occur between when we update the
inbox write pointer vs when the memory for the command actually gets
flushed from the map to the framebuffer.
DMCUB can read stale or partially invalid data when this race occurs.
[How]
Before updating the write pointer we can read back all pending commands
to ensure that we stall for the writes to be flushed to framebuffer.
We don't need to worry about choosing HDP vs VM flush with this
mechanism.
Drop the dmub_srv_cmd_submit() while we're updating this to work
correctly since nothing was actually using this API and the caller
should be explicit about the API flow here - by doing this on execute
we can give some extra time for the flush to finish while
preparing other commands.
We should try to avoid writing single commands
because of this overhead.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
While doing seamless boot I made some changes
to dcn2 hubbub functions, missed a link
[how]
link hubbub1 func to hubbub2 usage. It has already
been successfully linked in dcn1 and 3.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If the specific monitor supports DSC, the secondary link should be
disabled, and the other way around, too: if either that monitor or
our ASIC doesn't support DSC, the secodary link should be enabled.
[how]
Add a monitor patch and disable secondary link if that monitor
is detected and if ASIC supports DSC, or otherwise enable secondary
link.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Needed to reprogram vblank_start in dml properly in order to get the
correct dlg params to program VTG.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous implementation we may have residual chroma address offset
if transition from wa enable -> wa disable.
[How]
Clear address offset cache when viewport updates. Also update the
vp size check condition to account for rotation angle
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Upon exiting a fixed active VRR state, the state isn't cleared. This
leads to the variable VRR range to be calculated incorrectly.
[how]
Set fixed active state to false when updating vrr params
Signed-off-by: Amanda Liu <amanda.liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The conversion to bool is not needed, remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
read_current_link_settings_on_detect() on eDP 1.4+ may use the
edp_supported_link_rates table which is set up by
detect_edp_sink_caps(), so that function needs to be called first.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Martin Leung <martin.leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Only a single voltage level should be available to Pollock (min level)
Pollock & Dali get misidentified as Renoir, use wrong clk mgr constructor
[HOW]
Add provided Pollock IDs to ASIC Rev. ID list.
Create new Pollock ASIC RID check, fix RV2 & Dali ASIC checks.
Check RID and set max voltage level to 0 if Pollock is detected.
Work around broken ASICREV_IS_RENOIR, IS_RAVEN2, etc. checks by
performing Dali/Pollock checks before they can be misidentified as RN.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It won't get used unless the driver allows the gtt domain for
display buffers which is controlled elsewhere.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It won't get used unless the driver allows the gtt domain for
display buffers which is controlled elsewhere.
Acked-by: Huang Rui <ray.huang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a use case that link loss happens accidentally,
and we need to recover that link loss as soon as possible.
Under this circumstance, we will perform link training,
and try to recover the link that's just lost.
However, if link PHY is disabled before link training
happens, then DP display will never come back again.
Also, please note that dropping this disable_phy function
call won't break USB-C hotplug functionality.
(This line of code was firstly introduced associated with
a patch to fix USB-C hotplug issue)
[How]
Don't disable DP transmitter and its encoder before link
training happens, even if link loss is detected.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Compilation error "undefined reference to `__udivdi3'" was
thrown on i386 architecture.
[how]
Use div_u64 for unsigned long division instead of a divide operator.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Whenever a connector on an MST network is attached, detached, or
undergoes a modeset, the DSC configs for each stream on that
topology will be recalculated. This can change their required
bandwidth, requiring a full reprogramming, as though a modeset
was performed, even if that stream did not change timing.
Therefore, whenever a crtc has drm_atomic_crtc_needs_modeset,
for each crtc that shares a MST topology with that stream and
supports DSC, add that crtc (and all affected connectors and
planes) to the atomic state and set mode_changed on its state
v2: Do this check only on Navi and before adding connectors
and planes on modesetting crtcs
v3: Call the drm_dp_mst_add_affected_dsc_crtcs() to update
all affected CRTCs
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Since for DSC MST connector's PBN is claculated differently
due to compression, we have to recalculate both PBN and
VCPI slots for that connector.
[how]
The function iterates through all the active streams to
find, which have DSC enabled, then recalculates PBN for
it and calls drm_dp_helper_update_vcpi_slots_for_dsc to
update connector's VCPI slots.
v2: - use drm_dp_mst_atomic_enable_dsc per port to
enable/disable DSC
v3: - Iterate through connector states from the state passed
- On each connector state get stream from dc_state,
instead CRTC state
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If driver fails to update update VCPI allocation during
compute_mst_dsc_configs_for_state - fail the function
by return early.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If there is limited link bandwidth on a MST network,
it must be divided fairly between the streams on that network
Implement an algorithm to determine the correct DSC config
for each stream
The algorithm:
This
[ ] ( )
represents the range of bandwidths possible for a given stream.
The [] area represents the range of DSC configs, and the ()
represents no DSC. The bandwidth used increases from left to right.
First, try disabling DSC on all streams
[ ] (|)
[ ] (|)
Check this against the bandwidth limits of the link and each branch
(including each endpoint). If it passes, the job is done
Second, try maximum DSC compression on all streams
that support DSC
[| ] ( )
[| ] ( )
If this does not pass, then enabling this combination of streams
is impossible
Otherwise, divide the remaining bandwidth evenly amongst the streams
[ | ] ( )
[ | ] ( )
If one or more of the streams reach minimum compression, evenly
divide the reamining bandwidth amongst the remaining streams
[ |] ( )
[ |] ( )
[ | ] ( )
[ | ] ( )
If all streams can reach minimum compression, disable compression
greedily
[ |] ( )
[ |] ( )
[ ] (|)
Perform this algorithm on each full update, on each MST link
with at least one DSC stream on it
After the configs are computed, call
dcn20_add_dsc_to_stream_resource on each stream with DSC enabled.
It is only after all streams are created that we can know which
of them will need DSC.
Do all of this at the end of amdgpu atomic check. If it fails,
fail check; This combination of timings cannot be supported.
v2: Use drm_dp_mst_atomic_check to validate bw for certain dsc
configurations
v3: Use dc_dsc_policy structure to get min and max bpp rate
for DSC configuration
Acked-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to calculate VCPI slots differently for DSC
to take in account current link rate, link count
and FEC.
[how]
Add helper to get pbn_div from dc_link
Acked-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
For DSC case we cannot use topology manager's PBN divider
variable. The default divider does not take FEC into account.
Therefore the driver has to calculate its own divider based
on the link rate and lane count its handling, as it is hw specific.
[how]
Pass pbn_div as an argument, which is used if its more than
zero, otherwise default topology manager's pbn_div will be used.
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rework the dm_helpers_write_dsc_enable callback to
handle the MST case.
Use the cached dsc_aux field.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During MST mode enumeration, if a new dc_sink is created,
populate it with dsc caps as appropriate.
Use drm_dp_mst_dsc_aux_for_port to get the raw caps,
then parse them onto dc_sink with dc_dsc_parse_dsc_dpcd.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DSC MST, sometimes monitors would break out
in full-screen static. The issue traced back to the
PPS generation code, where these variables were being used
uninitialized and were picking up garbage.
memset to 0 to avoid this
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With DSC, bpp can be fractional in multiples of 1/16.
Change drm_dp_calc_pbn_mode to reflect this, adding a new
parameter bool dsc. When this parameter is true, treat the
bpp parameter as having units not of bits per pixel, but
1/16 of a bit per pixel
v2: Don't add separate function for this
v3: In the equation divide bpp by 16 as it is expected
not to leave any remainder
v4: Added DSC test parameters for selftest
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For high-res (8K) or HFR (4K120) displays, using uncompressed pixel
formats like YCbCr444 would exceed the bandwidth of HDMI 2.0, so the
"interesting" modes would be disabled, leaving only low-res or low
framerate modes.
This change lowers the pixel encoding to 4:2:2 or 4:2:0 if the max TMDS
clock is exceeded. Verified that 8K30 and 4K120 are now available and
working with a Samsung Q900R over an HDMI 2.0b link from a Radeon 5700.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Thomas Anderson <thomasanderson@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some combined docks will always trigger CP_IRQ but there's nothing the driver
needs to take care of, but the CP_IRQ breaks the original hdcp state and
triggers the driver to restart the authentication.
[How]
Add the event type check before restart the authentication or resend the stream
management
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some monitors trigger HDCP2.x timeout after reinitializing (e.g. toggling HDR)
by taking longer than expected to return h' (h prime)
Previously the 200ms watchdog timer retry count would hit
MAX_NUM_OF_ATTEMPTS (4), causing fallback to HDCP1.x
[HOW]
Adding a 1s delay after an h' watchdog timeout provides enough time
for affected monitors to return h' in time without hitting MAX_NUM_OF_ATTEMPTS
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Most DP/HDMI monitors need more time to response rx_validation
request.
[how]
Add generic 1000ms delay.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We are returning incorrect error code for validate h prime
[How]
Return the right Error code
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSP needs session ID to destroy a session, In the case where we fail
create session we don't have a session ID
[How]
Set the session ID before returning
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are returning SUCCESS when hdcp_status != Success. Fix it.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
list_for_each() can be replaced by the more concise
list_for_each_entry() here for iteration over the lists.
This change was reported by coccinelle.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:85:6-13: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:88:2-9: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:225:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:226:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:251:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:252:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:256:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:257:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:267:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:269:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:682:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:1013:1-9: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:110:6-13: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:113:2-9: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:243:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:244:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:267:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:268:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:272:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:273:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:283:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:285:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:673:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:962:1-9: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:110:6-13: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:113:2-9: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:243:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:244:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:267:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:268:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:272:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:273:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:283:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:285:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:673:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:961:1-9: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:157:46-64: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:159:2-20: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:161:46-64: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:163:2-20: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:289:1-12: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:290:1-12: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:341:3-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:343:4-15: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c:4124:3-28: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c:4128:5-30: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c:5207:3-37: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c:186:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c:189:2-10: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c:482:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c:485:2-10: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For udelay. This is needed for some platforms.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazluaskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's required for debug purposes.
[how]
Add a dsc_bpp_increment_div debug option that overrides DPCD
BITS_PER_PIXEL_INCREMENT value. The value dsc_bpp_increment_div should
be set to is the one after parsing, i.e. it could be 1, 2, 4, 8 or 16
(meaning 1pix, 1/2pix, ..., 1/16pix).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP is internal link and link loss is unexpected.
It is typically going to be PSR related errors, which is
handled separately.
[How]
Check for eDP and skip check for link loss
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor disappears for some SLS displays that are rotated 180
and 270 degrees. This occurs when there is no pipe split being
done ( ex. 3 or more displays ). The cursor calculations assume
pipe splitting is done so when it calculates the new cursor
position in hwss.set_cursor_position(), it is out-of-bounds so
it disables the cursor in hubp.set_cursor_position().
[How]
In non pipe split cases, calculate cursor using viewport size
( width or height ) instead of viewport size * 2 ( the two
because pipe splitting divides the rectangle into two ).
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous formula for calculating DPP CLK DTO was
hard to understand.
[How]
Replace with easier to understand formula that produces
same results.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A corner case currently exists where DPP DTO is lowered before
pipes are updated to a higher viewport. This causes underflow
as the DPPCLK is too low for the current viewport.
[How]
Only lower DPP DTO when it is safe to lower, or if
the newer clocks are higher than the current ones.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DAL3 should support SRIOV
[how]
Add support for the virtual dal flag. This flag should skip
most/all of DC construction since the HW isn't accessible, but
still construct WindowsDM (almost) normally but with only SW display
targets
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix manual trigger source correctly be TRIGA for DCN2
rather than MANUAL_FLOW.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN21 and DCN2 extended timeout support cap is not set correctly.
[How]
Set extended timeout support for ASIC families to their right values.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously update_bw_bounding_box for RN was commented out
due to incorrect values causing BSOD on Hybrid Graphics.
However, commenting out this function also may cause issues
such as underflow in certain cases such as 2x4K displays.
[How]
Fix dram_speed_mts calculations.
Update from proper index of clock_limits[]
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
According to eDP spec, max T7 delay should be 50 ms. Current code uses 300
retry counters may not be accurate enough for different panels.
[How]:
Use absolute time stamp to achive accurate delay.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we rotate 270 in mixed SLS mode, the recouts occupy the
right side of the display. So all the recout_skip_v values
are relative to the left side of the display. This causes
adjust_vp_and_init_for_seamless_clip() to incorrectly increase
the data->viewport.height for that recout. The rotation looks
like the bottom half is duplicated twice.
[How]
recout.x values are being adjusted based on
stream->timing.h_border_left. Instead of using h_border_left,
use dst.x to represent the border. Shift dst.x by the amount of
stream->timing.h_border_left and set
stream->timing.h_border_left to 0. Do all the calculations
and then revert stream->timing.h_border_left and
stream->dst.x back to their original values.
When calculating pipe_ctx->plane_res.scl_data.h_active,
make sure to use the original stream->timing.h_border_left
value.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Firmware state and tracebuffer shouldn't be considered stable API
between firmware versions.
Driver shouldn't be querying anything from firmware state or tracebuffer
outside of debugging.
Commands are the stable API for this once we have the outbox.
[How]
Add metadata struct to the end of the data firmware that describes
fw_state_size and some reserved area for future use.
Drop the tracebuffer and firmware state headers since they can differ
per version.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain instances, there was a reliance on pipe indexing being accurate. However, this
assumption fails with harvesting of pipes 1 or 2, which can occur in production B6 parts.
HW hang would occur as a result.
[How]
Use hubp index for mpcc, and do mpc_init for all theoretical pipes (including disabled ones).
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After read the 3rd Edid blocks, we will reset segment to 0,
which causes this VR fail to read Edid successfully.
[How]
Skip to reset segment to 0 for this VR device.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. Set second screen only then unplug external monitor
2. Enter to S4 then plug in external monitor
3. Resume from S4, eDP will not turn off when OS set
second screen only
Sometimes OS will not set eDP power up cause eDP dpms_off
keep true then driver skipp disable stream
[How]
When drvier try to disable stream, add link status condition
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DMUB is put into reset on suspend and is not running on resume,
disabling PSR/ABM features.
[How]
Move the allocation of the framebuffer to sw_init.
Do DMUB hardware init and framebuffer filling only from hw_init.
On resume the contents of the framebuffer will be invalid so those
should be cleared.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Up to 4 ODM memory pieces are required per ODM combine and cannot
overlap, i.e. each ODM "session" has to use its own memory pieces.
The ODM-memory mapping is currently broken for generic case.
The maximum number of memory pieces is ASIC-dependent, but it's always
big enough to satisfy maximum number of ODM combines. Memory pieces
are mapped as a bit-map, i.e. one memory piece corresponds to one bit.
The OPTC doing ODM needs to select memory pieces by setting the
corresponding bits, making sure there's no overlap with other OPTC
instances that might be doing ODM.
The current mapping works only for OPTC instance indexes smaller than
3. For instance indexes 3 and up it practically maps no ODM memory,
causing black, gray or white screen in display configs that include
ODM on OPTC instance 3 or up.
[how]
Statically map two unique ODM memory pieces for each OPTC instance
and piece them together when programming ODM combine mode.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add warmup escape support, for diags, in a way that is possible to
choose a new or an existing sequence. For achieving this goal, this
commit adds separated MCIF buffer as VCN request.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the global variable pow_buffer_ptr is set to -1, by definition
optimizations should not be used to build the regamma. Since
translate_from_linear_space unconditionally increments this global, it
inadvertently enables the optimization.
[How]
Increment pow_buffer_ptr only if it is not -1.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Scaling better handled by upper layers before pipe splitting.
[How]
Remove DC code for integer scaling and force cursor update if
viewport or scaling changes occur to prevent underflow from
invalid cursor position.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc previously had bugs that interfered with the ability to inherit a
timing from a device with multiple streams (without flash/blanking).
After this fix there is still a dependency on UEFI support.
[how]
fixed 3 bugs: loaded MPC state, changed bw_optimize flag to a counter
instead of a boolean, and reading dpp/disp clk from HW to ensure we
don't raise the clock's when we're not supposed to.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some 10bit eDP panels don't lightup after we cap bpc to 8.
[How]
Set default max_bpc to 16 for edp connector type.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, pipe resources are assigned to an index that matches the pipe position.
However, if pipe 1 or 2 is disabled, there will be a gap in the arrays which causes a crash when iterating based on pipe_count.
[How]
Fix resource construct to assign resources to minimum available array index.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need previously implemented chroma vp wa to work for rotation cases.
[How]
Implement rotation specific wa.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is one opp per pipe. For certain RN parts, the fourth pipe is disabled, so there is no opp for it.
res_cap->num_opp is hardcoded to 4, so if we use that to iterate over opps we will crash.
[How]
Use the pipe_count value instead, which is not hardcoded and so will have the correct number.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We want to streamline the calculations made when entering LFC.
Previously, the optimizations led to screen tearing and were backed out
to unblock development.
[how]
Integrate other calculations parameters, as well as screen tearing,
fixes with the original LFC calculation optimizations.
Signed-off-by: Amanda Liu <amanda.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
YQ should be limited range for all cases.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A hardcoded number is used today
[How]
Add definition for number of BL data points
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some use cases we need to be able to adjust the maximum target bpp
allowed by DSC policy.
[How]
New interface dc_dsc_policy_set_max_target_bpp_limit
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
CW0 and CW1 need to use physical addressing mode for dcn20 and dcn21.
The current code for dcn20 is using virtual.
[How]
We already program the DMCUB like this on dcn21 so we should just use
the same sequence for both.
Copy the dcn21 sequences into the dmjub_dcn20.c file and rename them.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These values can differ per ASIC and should follow the full DC style
register programming model.
[How]
Define a common list and fill in the common list separately for
dcn20 and dcn21.
Unlike DC we're not using designated initializers for better compiler
compatibility since this resides in the DMUB service.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Lack of proper timing caused intermittent underflow on unplug external DP.
A previous fix was invalid and caused S0i3 regression, so had to be reverted.
[How]
When unlocking pipe, wait for no pipes to have flip pending before unlocking.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The earlier change: "check phy dpalt lane count config"
uses link encoder registers not defined properly.
That caused regression with mst-enabled display not
lighting up.
[How]
Add missing reg definitions.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc20 containes several FPU-dependent functions without proper FPU
kernel mode enable/disable wrappers. Add the required wrappers
for both x86 and POWER.
This enables Navi DC20 support for POWER systems.
v2: fix compilation
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN requires floating point support to operate. Add the appropriate
x86/ppc64 guards and FPU / AltiVec / VSX context switches to DCN.
Note that the current DC20 code doesn't contain all required FPU
wrappers on x86 or POWER, so this patch is insufficient to fully
enable DC20 on POWER.
v2: s/X86_64/X86/g to retain previous behavior.
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Introduce DC_FP_START()/DC_FP_END() macros to help enable floating
point kernel mode support across various architectures.
v2: move copyright update to commit which adds the changes
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-next-5.6-2019-12-11:
amdgpu:
- Add MST atomic routines
- Add support for DMCUB (new helper microengine for displays)
- Add OEM i2c support in DC
- Use vstartup for vblank events on DCN
- Simplify Kconfig for DC
- Renoir fixes for DC
- Clean up function pointers in DC
- Initial support for HDCP 2.x
- Misc code cleanups
- GFX10 fixes
- Rework JPEG engine handling for VCN
- Add clock and power gating support for JPEG
- BACO support for Arcturus
- Cleanup PSP ring handling
- Add framework for using BACO with runtime pm to save power
- Move core pci state handling out of the driver for pm ops
- Allow guest power control in 1 VF case with SR-IOV
- SR-IOV fixes
- RAS fixes
- Support for power metrics on renoir
- Golden settings updates for gfx10
- Enable gfxoff on supported navi10 skus
- Update MAINTAINERS
amdkfd:
- Clean up generational gfx code
- Fixes for gfx10
- DIQ fixes
- Share more code with amdgpu
radeon:
- PPC DMA fix
- Register checker fixes for r1xx/r2xx
- Misc cleanups
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191211223020.7510-1-alexander.deucher@amd.com
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
-----BEGIN PGP SIGNATURE-----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=b15X
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-12-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
amdgpu is MIT licensed.
Fixes: ec8f24b7fa ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling kzalloc() and related functions requires the
linux/slab.h header to be included:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c: In function 'dcn21_ipp_create':
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c:679:3: error: implicit declaration of function 'kzalloc'; did you mean 'd_alloc'? [-Werror=implicit-function-declaration]
kzalloc(sizeof(struct dcn10_ipp), GFP_KERNEL);
A lot of other headers also miss a direct include in this file,
but this is the only one that causes a problem for now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu is MIT licensed.
Fixes: ec8f24b7fa ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling kzalloc() and related functions requires the
linux/slab.h header to be included:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c: In function 'dcn21_ipp_create':
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c:679:3: error: implicit declaration of function 'kzalloc'; did you mean 'd_alloc'? [-Werror=implicit-function-declaration]
kzalloc(sizeof(struct dcn10_ipp), GFP_KERNEL);
A lot of other headers also miss a direct include in this file,
but this is the only one that causes a problem for now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An initialization was added for two optional struct members. One of
these is always present in the dcn20_resource file, but the other one
depends on CONFIG_DRM_AMD_DC_DSC_SUPPORT and causes a build failure if
that is missing:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_resource.c:926:14: error: excess elements in struct initializer [-Werror]
.num_dsc = 5,
Add another #ifdef around the assignment.
Fixes: c3d03c5a19 ("drm/amd/display: Include num_vmid and num_dsc within NV14's resource caps")
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid a compiler warning.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems always request passive flip on RN due to incorrect compare
clock state to determine optization.
[How]
Instead of calling memcmp, compare clock state member to determine the
condition.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a timeout occurs after a DEFER, some devices require more retries
than in the case of a regular timeout.
[How]
In a timeout occurrence, check whether a DEFER has occurred before the
timeout and retry MAX_DEFER_RETRIES retries times instead of
MAX_TIMEOUT_RETRIES.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Value obtained from DV is not allowing 8k60 CTA mode with DSC to
pass, after checking real value being used in hw, find out that
correct value is 3600, which will allow that mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Screen tearing is present in tests when setting the frame rate to
certain fps
[How]
Revert previous optimizations for low frame rates.
Signed-off-by: Amanda Liu <amanda.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
During mode transition steer fifo could overflow. Quite often it
recovers by itself, but sometimes it doesn't.
[how]
Add steer fifo reset before unblanking the stream. Also add a short
delay when resetting dig resync fifo to make sure register writes
don't end up back-to-back, in which case the HW might miss the reset
request.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The variable mismatch assignment error.
[How]
To use uint32_t replace it.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP spec requires 1000 symbols delay between the end of link training
and enabling FEC in the stream. Currently we are using 1 miliseconds
delay which is not accurate.
[how]
One lane RBR should have the maximum time for transmitting 1000 LL
codes which is 6.173 us. So using 7 microseconds delay instead of
1 miliseconds.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new sr and pstate latencies are optimized for the case when we are not
using lpddr4 memory
[How]
have two different wm tables, one for the lpddr case and one for
non lpddr case
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When video_memory_type bw_params->vram_type
is assigned, wedistinguish between Ddr4MemType and LpDdr4MemType.
Because of this we will never report that we are using
LpDdr4MemType and never re-purpose WM set D
[How]
populate bios integrated info for renoir by adding the
revision number for renoir and use that integrated info
table instead of of asic_id to get the vram type
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pstate_latency_us never gets updated from the hard coded value
in rn_clk_mgr.c
[how]
update the wm table's values before we do calculations with them
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On ASICs where number of DSCs is the same as OPPs there's no need
for DSC resource management. Mappping 1-to-1 fixes mode-set- or S3-
-related issues for such platforms.
[how]
Map DSC resources 1-to-1 to pipes only if number of OPPs is the same
as number of DSCs. This will still keep other ASICs working.
A follow-up patch to fix mode-set issues on those ASICs will be
required if testing shows issues with mode set.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers.
[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To quickly validate whether DMCUB is running and accepting commands for
offload testing we want to intercept a common sequence as part of
modeset programming.
[How]
OTG enable will cause the most impact in terms of golden register
changes and it's a single register write.
This approach was previously done in dcn10 code when it was shared with
dcn20 but it wasn't ported over to the dcn20 code.
Port over start, execute and wait sequence into dcn20_optc.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When setting lttpr mode, the new mode to bet is not logged properly.
[How]
Update log message to show the right mode.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation for further changes
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems always request passive flip on RN due to incorrect compare
clock state to determine optization.
[How]
Instead of calling memcmp, compare clock state member to determine the
condition.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a timeout occurs after a DEFER, some devices require more retries
than in the case of a regular timeout.
[How]
In a timeout occurrence, check whether a DEFER has occurred before the
timeout and retry MAX_DEFER_RETRIES retries times instead of
MAX_TIMEOUT_RETRIES.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we require HDR_MULT >= 1.0
There are scenarios where we need < 1.0
[How]
Only guard against 0 - it will black-screen image.
It is up to higher-level logic to decide what HDR_MULT
values are allowed in each particular case.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need support for more color management in 10bit
surface.
[How]
Provide support for DePQ for 10bit surface
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Value obtained from DV is not allowing 8k60 CTA mode with DSC to
pass, after checking real value being used in hw, find out that
correct value is 3600, which will allow that mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Screen tearing is present in tests when setting the frame rate to
certain fps
[How]
Revert previous optimizations for low frame rates.
Signed-off-by: Amanda Liu <amanda.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor position needs to take into account plane scaling as well.
[How]
Translate cursor coords from stream space to plane space.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is causing green Line at the bottom of SDR 480p
MPO playback
[How]
Limit workaround to vertical > 512
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc needs to expose its internal dsc policy.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
add_dsc_to_stream_resource could be called for validation.
Failing validation is completely fine.
However failing it inside commit streams is bad.
This code could be triggered for both contexts.
The function itself cannot distinguish the caller, which
makes it impossible to output the log only in the
meaningful case (commit streams).
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to support 6 bpp for 420 pixel encoding only.
[how]
Add a dc function to determine what bpp range can be supported
for given pixel encoding.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I was advised that we don't need this call of program_front_end, as
earlier and later calls in the same sequence are sufficient.
[How]
Remove first call of program_front_end in dc_commit_state_no_check.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I was advised that we may need to check for mpcc idle in more cases
than just when opp_changed is true. Also, mpcc_inst is equal to
pipe_idx, so remove for loop.
[How]
Remove opp_changed flag check and mpcc_inst loop.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When training with repeater the aux read interval must be set to
repeater specific aux_red_interval. This value is always 100us for CR.
[How]
Check for repeater when setting the aux_rd_interval in channel
equalization.
Use the right offset in the aux_rd_interval array
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: George Shen <George.Shen@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MPCC programming was being missed during certain split pipe enables due
to full_update flag not being true. This caused a momentary flash on
half the screen. After discussion, determined we should not have that
flag check within update_mpcc, as it should always perform full
programming when called.
[How]
Remove flag check. We call update_blending within insert_plane, so we
do not need to replace its call from the if block.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized sr latency numbers, for lpddr4
[How]
change the sr laency in the lpddr4 wm table to the new latency
number
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Scratch registers are limited on the DMCUB and we have an expanding
list of state to track between driver and DMCUB.
[How]
Place shared state in cache window 6. The cache window size is aligned
to the size of the cache line on the DMCUB to make it easy to
invalidate.
The shared state is intended to be read only from driver side so
it's been marked as const.
The use of volatile is intentional. The memory for the shared firmware
state is memory mapped from the framebuffer memory. The DMCUB will
flush its cache after modifying the region. There's no way for x86
to known whether this data is stale or not so we want to intentionally
disable optimization to force the read at every access.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
