[why]
When display is connected with a native DP port, DP2 mode register value
is a don't care. Driver mistakenly reduce max supported lane count to 2
lane based on the don't care value.
[how]
Add additional check only if USB C DP alt mode is enabled, we will
determine max lane count supported based on current mode.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In cases where a clock table is malformed such that fclk entries have
frequencies but not voltages listed, we don't catch the error and set
clocks to 0 instead of using hardcoded values as we should.
[HOW]
Add check for clock tables fclk entry's voltage as well
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If dc->clk_mgr->funcs->are_clock_states_equal is set, then
wm_optimized_required is never checked. In that case, when going from a
higher mode to a lower mode, wm_optimized_required remains true until
the next mode change.
[How]
- move from else-if to unconditional or
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In most cases, DRAM watermark is large enough that the result of the
condition to increase TTU doesn't change after DRAM watermark is
increased. However, there is are cases where the condition fails and
becomes true after DRAM watermark is increased. This results in minTTU <
DRAM watermarks which leads to PSR hang since p-state is requested but
not allowed.
[How]
Check whether to update TTU after DRAM watermark is updated.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some usecases, like tiled display, the stream and plane configuration
can be setup in a way where the caller expects DAL to perform the
clipping, eg:
P0:
src_rect(0, 0, w, h)
dst_rect(0, 0, w, h)
P1:
src_rect(w, 0, w, h)
dst_rect(0, 0, w, h)
Cursor is enabled on both streams with the same position.
This can result in double cursor on tiled display, even though this
behavior is technically correct from the DC interface point of view.
We need a mechanism to control this dynamically.
[How]
This is something that should live in the DM layer based on detection
of the specified configuration but it's not something that we really
have enough information to deal with today.
Add a flag to the cursor position state that specifies whether we
want DC to do the translation or not and make it opt-in and let
the DM decide when to do it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
New formula + cursor change causing underflow
on certain configs
[How]
Rever to old formula
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
usb3->usb2 switch system hang.
driver needs to limit the max sink cap based on DP4 mode.
[how]
based on s_dpalt check and DP4 check:
limit the USB-C DPALT DP maximum supported lane count.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dml merges mpc/odm combine pipes to do calculations. This merge is
imperfect if there is a viewport overlap. This change saves pre overlap
viewport for dml use.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After v_total_min and max are updated in vrr structure, the changes are
not reflected in stream adjust. When these values are read from stream
adjust it does not reflect the actual state of the system.
[How]
Set stream adjust values equal to vrr adjust values after vrr adjust
values are updated.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If a plane isn't being actively enabled or disabled then DC won't
always recalculate scaling rects and ratios for the primary plane.
This results in only a partial or corrupted rect being displayed on
the screen instead of scaling to fit the screen.
[How]
Add back the logic to recalculate the scaling rects into
dc_commit_updates_for_stream since this is the expected place to
do it in DC.
This was previously removed a few years ago to fix an underscan issue
but underscan is still functional now with this change - and it should
be, since this is only updating to the latest plane state getting passed
in.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For medium updates that change nothing but the source rect position
the viewport doesn't change on DCN20.
We're missing the check for the position update bit that was there in
the DCN10 hardware sequencer.
[How]
Check the position bit along with the scaling bit like we were doing
with DCN20.
We shouldn't actually hit a case where context != current_state in
our programming/commit model but guard against it anyway since it was
guarded for the other bits.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor pos is correctly adjusted from DC side for source rect offset
on DCN ASIC, but only on the overlay.
This is because DM places offsets the cursor for primary planes only
to workaround missing code in DCE for the adjustment we're now correctly
doing in DC for DCN ASIC.
[How]
Drop the adjustment for source rect from the DM side of things and put
the code where it actually belongs - in DC on the pipe level.
This matches what we do for DCN now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Changing policy to dynamic will allow 4k multi display configs
to be supported at DPM0
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor is drawn as part of the framebuffer for a plane on AMD hardware.
The cursor position on the framebuffer does not change even if the
source rect viewport for the cursor does. This causes the cursor to be
clipped.
The following IGT tests fail as a result of this issue:
- kms_plane_cursor@pipe-*-viewport-size-*
[How]
Offset cursor position by plane source rect viewport. If the viewport
is unscaled then the cursor is now correctly positioned on any
plane - primary or overlay.
There is still a hardware limitation for dealing with the cursor size
being incorrectly scaled but that's not something we can address.
Add some documentation explaining some of this in the code while we're
at it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
blank all dp stream would impact edp
[how]
only blank the one which will be powered off
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When dmcub is the default we no longer wish to create the psr and dmcu
objects. Currently a dc debug flag is used to implement this, but these
flags aren't populated until after dcn21_resource_construct is called.
This means the dmcub objects will never be created. Therefore we must
use a dc config flag, which is populated before dc resource construct.
[How]
Add a dc config flag.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The power_down() function was only defined for specific asics and will
crash the system if it is called by an asic with eDP connected that does
not have it defined.
[HOW]
Add a check for the function's existence before calling it.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Overlay planes disappear when the plane's alpha blending mode or global
opacity is modified.
These are considered UPDATE_TYPE_MEDIUM and trigger the update_mpcc path
in the DCN hardware sequencer.
On DCN10 we have an "optimization" to avoid touching the blending tree
on these updates, but this is actually required behavior based on how
update_mpcc is structured.
For full updates we acquire a MPCC for the plane, remove it if it
already exists then reinsert it after with insert_plane.
The call to insert_plane can take an optional mpcc to insert the new one
above to preserve the current blending order. The update_mpcc hwseq
function doesn't do this so the overlay gets sent to the very bottom
of the tree.
[How]
Copy the check over from DCN10 to DCN20. The only time we need to
actually touch the tree really is the full update, so this is also
an optimization on top of the fix.
Fixing the logic for insert_plane is rather simple (cache the bot_mpcc
and pass it to insert_plane) but is a change that impacts most display
usecases.
For now stick with the optimization.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
power off dp receiver directly cause garbage during hw init
[how]
blank dp stream and then power off receiver
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On headless boot a DIG may be turned on by VBIOS on RN. This leads to
display_count being non-zero in hybrid graphics cases leading to SMU
DISPLAY_OFF message not being sent.
[HOW]
Power down hardware on boot
if seamless boot is not occurring
(power_down_display_on_boot == 1)
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver must pass abm config table to dmub fw. This provides various
parameters for abm functionality.
[How]
There is too much data to be passed in an inbox message, so we must pass
this data using an indirect buffer. Copy the table to cw7 via x86,
driver copies to fw_state structure.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Link or DIG BE can't be exposed to a higher stream bandwidth than they
can handle. When DSC is required to fit the stream into the link
bandwidth, DSC has to be programmed before the link is enabled to ensure
this. Without it, intermittent issues such as black screen after S3 or a
hot-plug can be seen with DSC timings like 4k144Hz or 8k60Hz.
[how]
Move DSC programming from before enabling stream to before enabling link
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If no free pipes are available, acquire_first_split_pipe is called to
get a pipe to use. This call may alter the ordering of the pipes in the
list so that, for example, the tail pipe changes.
If acquire_first_split_pipe returns the tail pipe, we'll have free_pipe
== tail_pipe. What tail_pipe refers to is not the current tail_pipe, but
what was previously the tail pipe - i.e. prior to the call to
acquire_first_split_pipe
The logic that follows will link free_pipe to the tail pipe, referring to
the current tail pipe. However, since tail_pipe is cached from before the
call to acquire_first_split_pipe, the wrong tail pipe will be used, and
it will end up being linked to itself, creating a loop that, if traversed,
will result in a soft hang.
[How]
Do not cache the tail pipe. Instead, check the tail pipe after the call to
acquire_first_split_pipe is made.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
Aligh with DP spec wanted to follow same naming convention.
[How]:
Changed the macro name of the dpcd address used for getting requested
test-pattern.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-2-animesh.manna@intel.com
[WHY]
In cases where a clock table is malformed such that fclk entries have
frequencies but not voltages listed, we don't catch the error and set
clocks to 0 instead of using hardcoded values as we should.
[HOW]
Add check for clock tables fclk entry's voltage as well
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
If dc->clk_mgr->funcs->are_clock_states_equal is set, then
wm_optimized_required is never checked. In that case, when going from a
higher mode to a lower mode, wm_optimized_required remains true until
the next mode change.
[How]
- move from else-if to unconditional or
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some usecases, like tiled display, the stream and plane configuration
can be setup in a way where the caller expects DAL to perform the
clipping, eg:
P0:
src_rect(0, 0, w, h)
dst_rect(0, 0, w, h)
P1:
src_rect(w, 0, w, h)
dst_rect(0, 0, w, h)
Cursor is enabled on both streams with the same position.
This can result in double cursor on tiled display, even though this
behavior is technically correct from the DC interface point of view.
We need a mechanism to control this dynamically.
[How]
This is something that should live in the DM layer based on detection
of the specified configuration but it's not something that we really
have enough information to deal with today.
Add a flag to the cursor position state that specifies whether we
want DC to do the translation or not and make it opt-in and let
the DM decide when to do it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If a plane isn't being actively enabled or disabled then DC won't
always recalculate scaling rects and ratios for the primary plane.
This results in only a partial or corrupted rect being displayed on
the screen instead of scaling to fit the screen.
[How]
Add back the logic to recalculate the scaling rects into
dc_commit_updates_for_stream since this is the expected place to
do it in DC.
This was previously removed a few years ago to fix an underscan issue
but underscan is still functional now with this change - and it should
be, since this is only updating to the latest plane state getting passed
in.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For medium updates that change nothing but the source rect position
the viewport doesn't change on DCN20.
We're missing the check for the position update bit that was there in
the DCN10 hardware sequencer.
[How]
Check the position bit along with the scaling bit like we were doing
with DCN20.
We shouldn't actually hit a case where context != current_state in
our programming/commit model but guard against it anyway since it was
guarded for the other bits.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor pos is correctly adjusted from DC side for source rect offset
on DCN ASIC, but only on the overlay.
This is because DM places offsets the cursor for primary planes only
to workaround missing code in DCE for the adjustment we're now correctly
doing in DC for DCN ASIC.
[How]
Drop the adjustment for source rect from the DM side of things and put
the code where it actually belongs - in DC on the pipe level.
This matches what we do for DCN now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Changing policy to dynamic will allow 4k multi display configs
to be supported at DPM0
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor is drawn as part of the framebuffer for a plane on AMD hardware.
The cursor position on the framebuffer does not change even if the
source rect viewport for the cursor does. This causes the cursor to be
clipped.
The following IGT tests fail as a result of this issue:
- kms_plane_cursor@pipe-*-viewport-size-*
[How]
Offset cursor position by plane source rect viewport. If the viewport
is unscaled then the cursor is now correctly positioned on any
plane - primary or overlay.
There is still a hardware limitation for dealing with the cursor size
being incorrectly scaled but that's not something we can address.
Add some documentation explaining some of this in the code while we're
at it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After v_total_min and max are updated in vrr structure, the changes are
not reflected in stream adjust. When these values are read from stream
adjust it does not reflect the actual state of the system.
[How]
Set stream adjust values equal to vrr adjust values after vrr adjust
values are updated.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DRM already supports tracing DPCD transactions, there's no reason for
the existence of this function. Also, it prints one byte per-line which
is way too loud. So, just remove it.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues in dc_link file, on dc_link_construct and
translate_encoder_to_transmitter as suggested by checkpatch.pl.
Types covered:
CHECK: Lines should not end with a '('
WARNING: Missing a blank line after declarations
CHECK: Alignment should match open parenthesis
CHECK: Comparison to NULL could be written
CHECK: Logical continuations should be on the previous line
CHECK: Blank lines aren't necessary after an open brace '{'
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues on the file dc_link between is_same_edid and
get_ddc_line as suggested by checkpatch.pl.
Types covered:
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Blank lines aren't necessary before a close brace '}'
WARNING: braces {} are not necessary for single statement blocks
CHECK: Comparison to NULL could be written
CHECK: Lines should not end with a '('
CHECK: Alignment should match open parenthesis
CHECK: Using comparison to false is error prone
CHECK: Using comparison to true is error prone
WARNING: Avoid multiple line dereference - prefer 'link->dpcd_caps.sink_count.bits.SINK_COUNT'
CHECK: Unnecessary parentheses around
WARNING: Missing a blank line after declarations
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues on the file dc_link until detect_dp func as
suggested by checkpatch.pl.
Types covered:
CHECK: Please don't use multiple blank lines
CHECK: Comparison to NULL could be written
ERROR: space required before the open parenthesis '('
CHECK: Alignment should match open parenthesis
CHECK: Lines should not end with a '('
WARNING: please, no space before tabs
WARNING: Comparisons should place the constant on the right side of the test
WARNING: braces {} are not necessary for single statement blocks
CHECK: Please don't use multiple blank lines
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Can't call dmub_abm_enable_fractional_pwm from dmub_abm_create as
dmub_srv is still null at this init stage, and therefore can't call to
fw.
[How]
Move call to dmub_abm_init_backlight. This should be the first call from
the driver for ABM.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML expects num_states to exclude the duplicate state.
[How]
Set num_states to correct value to prevent array off-by-one error. Also
refactor max clock level code for diags.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
CTM was only supported at CRTC level and we need color space conversion
in linear space at plane level.
[How]
- Add plane-level CTM to dc interface
- Program plane-level CTM in DCN
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some scenario like 1366x768 VSR enabled connected with a 4K monitor
and playing 4K video in clone mode, underflow will be observed due to
decrease dppclk when previouse surface scan isn't finished
[How]
In this use case, surface flip is switching between 4K and 1366x768,
1366x768 needs smaller dppclk, and when decrease the clk and previous
surface scan is for 4K and scan isn't done, underflow will happen. Not
doing optimize bandwidth in case of flip pending.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some monitors extreme flickering can occur while using LFC for if
we're not doing the DRR timing update for V_TOTAL_MIN / V_TOTAL_MAX at
the DP start of frame.
Hardware can default to any time in the frame which isn't the behavior
we want.
[How]
Add a new function for setting the double buffering mode for DRR timing.
Default to DP start of frame double buffering on timing generator init.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
P010 pixel format is not declared as supported in DRM and DM.
[How]
Add P010 format to the support list presented to DRM and checked in DM
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Diagnostics scaling test failing to set required number of vertical taps
in 4:2:0 surface case
[How]
In dpp3_get_optimal_number_of_taps() need to use LB_MEMORY_CONFIG_3 for
4:2:0 surface case. In resource_build_scaling_params() make sure to also
set plane res alpha enable based on updated surface state
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds logic that will determine if pipes need merging during validation.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
before update dpp DTO, we check dppclks in context to determine it is
changed or not, but dppclks in context will be updated anyways after
flip is done, so compare dppclks in context will always get an equal
result.
[How]
Add pipe dpp clks in dccg and compare values between dccg and context.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Causes regression with MST DSC displays not lighting up after DPMS
[how]
Revert commit 8cc426d79b ("drm/amd/display: Program DSC during timing programming")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
underflow happened when playing video on 1366x768 + 4K clone mode due to
incorrect handle watermark change flag and lower down clocks to early.
[How]
Check watermark change flag when decide doing optimized, and check
optimized required flag to do clock update.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
this register not exist in some asic, based on request remove this from
dc.
[how]
add guard for sanization.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should check MST BU support capability on output port before building
vsc info packet.
[How]
Add a new definition for port and sink capability check.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless boot cases, self refresh control registers are not
programmed on boot. In certain hybrid graphics cases this may cause
cstate entering to get blocked causing a hang.
[HOW]
Program self refresh control register on boot.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable/disable psr on dmcub and fallback to dmcu
when necessary.
[How]
Use dc config option to do so.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The default value for disable_dmcu is true, even for asics that require
dmcu.
[How]
Set flag properly per asic.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A "dcn20_program_front_end_for_ctx" warning is observed on Renoir.
Since the resource definition doesn't explicitly disable triplebuffer
flips like Navi10 DC actually attempts to go and setup triplebuffering
even when we pass in false to the plane state.
If we hit a full update after triplebuffering has been setup we see the
assertion since we don't expect full updates while performing
triplebuffer flips.
Normally this would get reset back to false whne we pass in the new
plane state, but since we never actually copy the flag when doing
surface updates this doesn't happen.
[How]
Copy the flag onto the plane update based on the requested surface
update state.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Right now only stream count is used to avoid split. This change updates
the W/A to check plane count instead.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When hotplug a HDMI monitor during entering S0i3 or DPMSOFF state due to
entering infinite loop when calling vbios to program pixel clocks. In
this scenario, pll is enabled but phy is not, and there is not a
programing guide for this case.
[How]
Before we having the proper programing guide, before disable pll, doing
a phy enable and disable to avoid the issue.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When reprogram MSA with updated color space, the test color space shows
inconsistency. Linux has separate routine to set up test pattern color
space, but it fails to configure RGB.
[How]
Add RGB to test pattern.
Fixes: 43563bc2e6 ("drm/amd/display: update MSA and VSC SDP on video test pattern request")
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Not programming dto with same values causes test failures in DCN2 diags
DPP tests.
[HOW]
This reverts commit 1b53e73323.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes a problem found on the MacBookPro 2017 Retina panel:
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2
aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel on Linux <= 5.5. Additionally, commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")'
introduced into Linux 5.6-rc1 will unclamp panel depth to
its full 10 bpc, thereby requiring a eDP bandwidth for all
modes that exceeds the bandwidth available and causes all modes
to fail validation -> No modes for the laptop panel -> failure
to set any mode -> Panel goes dark.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to override reported max link rate to the correct maximum
of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display
precision.
Please apply for Linux 5.6+ to avoid regressing Apple MBP panel
support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If "speed" is zero then we use it as a divisor to find "prescale". It's
better to move the check for zero to the very start of the function.
Fixes: 9eeec26a13 ("drm/amd/display: Refine i2c frequency calculating sequence")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can remove the NULL check for "res_ctx" and
"res_ctx->pipe_ctx[i].stream->link". Also it's nicer to align the
conditions using spaces so I re-indented a bit.
Longer explanation: The "res_ctx" pointer points to an address in the
middle of a struct so it can't be NULL. For
"res_ctx->pipe_ctx[i].stream->link" we know that it is equal to "link"
and "link" is non-NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In dcn20_funcs and dcn21_funcs struct, the member ".dsc_pg_control = NULL"
should be removed due to .dsc_pg_control be assigned to dcn20_dsc_pg_control.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem Description:
Currently we are checking internal fused rev id with pci rev id. However, fused
internal rev id is the same on all raven2 parts (in which Dali and Pollock were
based on too), thus Pollock detection fails
Fix:
use the pci rev to preform the detection for bandwidth calculations.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Aly-Tawfik <altawfik@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dpp2_get_optimal_number_of_taps function is never used. Removing
just for code cleaning up.
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
FEC capability query should not be affected by debugging decision on
whether to disable FEC. We should not determine if display supports FEC
by checking debug option.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
on some displays that prefer swapped polarity we were seeing L/R images
swapped because OTG_STEREO_SYNC_OUTPUT_POLARITY would always be mapped
to 0
[how]
fix initial dal3 implementation to properly update the polarity field
according to the crtc_stereo_flags (same as
OTG_STEREO_EYE_FLAG_POLARITY)
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Link or DIG BE can't be exposed to a higher stream bandwidth than they
can handle. When DSC is required to fit the stream into the link
bandwidth, DSC has to be programmed during timing programming to ensure
this. Without it, intermittent issues such as black screen after S3 or a
hot-plug can be seen.
[how]
Move DSC programming from enabling stream on link to timing setup.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System isn't able to enter S0i3 due to not send display count 0 to smu.
When dpms off, clk changed flag is cleared alreay, and it is checked
when doing optimized bandwidth, and update clocks is bypassed due to the
flag is unset.
[How]
Remove check flag incide the function since watermark values and clocks
values are checked during update to determine whether to perform it, no
need to check it again outside the function.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
Need debug options to control lightl/deep sleep
[How]
Add registry for memory power control
Signed-off-by: Braden Bakker <Braden.Bakker@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It is possible even if sink signal is MST but driver enables SST stream.
We should not determine if we should do MST authentication based on
sink's capability.
Instead we should determine whether to do MST authentication based on
what we have enabled in stream.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
nv14 previously inherited soc bb from generic dcn 2, did not match
watermark values according to memory team
[how]
add nv14 specific soc bb: copy nv2 generic that it was
using from before, but changed num channels to 8
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:31: warning:
address of 'pipe_ctx->plane_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:56: warning:
address of 'pipe_ctx->stream_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~~
2 warnings generated.
As long as pipe_ctx is not NULL, the address of members in this struct
cannot be NULL, which means these checks will always evaluate to false.
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Link: https://github.com/ClangBuiltLinux/linux/issues/915
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some lttpr devices do not work properly when lttpr mode is configured
after link settings.
[How]
Move lttpr configuration before lane settings.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disabling FEC for specific monitors is sometimes required for debugging
while in the monitor bringup phase
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We see an issue that caused clk_optimized_required to be set true in
certain cases, causing passive flips to fail. This is because of a typo
where wm_optimized_required was set twice.
[HOW]
Set clk_optimized_required to false after updating clocks.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vstartup calculation is incorrect due to use 2 number of cursors and
result in an underflow when playing video in full screen mode and
combines graphic plane and video plane.
[How]
Apply new policy for dml calculation.
1 cursor for graphic plane, 0 cursor for video plane.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Freesync borderless is not meant to be enabled on any APUs
[HOW]
Add is_apu cap to dcn21_resource_construct for correct recognition
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SMU FW previously had an issue with lowering display clock to below 100
MHz, and a workaround was put in to limit it. Newest SMU FW does not
have this issue, and no longer needs the 100MHz cap.
[HOW]
Remove the 100MHz cap based on the SMU FW version.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When combining two or more pipes in DSC mode, there will always be more
than 1 slice per line. In this case, as per DSC rules, the sink device
is expecting that the ICH is reset at the end of each slice line (i.e.
ICH_RESET_AT_END_OF_LINE must be configured based on the number of
slices at the output of ODM). It is recommended that software set
ICH_RESET_AT_END_OF_LINE = 0xF for each DSC in the ODM combine. However
the current code only set ICH_RESET_AT_END_OF_LINE = 0xF when number of
slice per DSC engine is greater than 1 instead of number of slice per
output after ODM combine.
[how]
Add is_odm in dsc config. Set ICH_RESET_AT_END_OF_LINE = 0xF if either
is_odm or number of slice per DSC engine is greater than 1.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When test pattern is enabled with ODM combine, test pattern is generated
by piecing multiple DPGs image together. The current code will program
all DPGs with horizontal offset of 0. This will cause all DPGs to output
the beginning of the pattern. Instead each DPG should program a
horizontal offset of its x position to form a continous pattern when
pieced together.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Allow vsc info packet if vsc is supported. Update vsc based on test
pattern request. Remove dpg_is_blanked polling, apply hardware global
lock instead to ensure double buffered dpg is updated with vsc in one
frame
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
In order to correctly intepret clock table, num_states is also needed.
This field did not get moved with clock_table but should next to it for
easier access/viewing.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we have single channel memory, we can not light up 2 4k displays
with a 1080p edp, because we don't have enough bw by a small margin.
this small margin comes from dcc meta being too large. We however don't
have this dcc meta when we create fake planes so, before the flip we
will not filter out the mode for 2 4k displays with a 1080p edp
[how]
Change get_default_swizzle_mode to something more general so we don't
end up with a separate function for every missing field in the fake
plane. Add a reasonable dcc meta to the fake plane when it is filled in,
so we filter out modes that don't have enough bandwidth. To do this, we
take the screen width and align it to 1024(8k 60)
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some asics don't support FEC but FEC overhead is added into link
bandwidth calculation by mistake. This causes certain timing cannot be
validated.
[how]
Only include FEC overhead if both asic and display support FEC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Move psr_on_dmub flag from dc_debug_options to dc_config.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern we mistook dp_hw_link_settings
for a redundant call of dpcd_set_link_settings
[How]
revert the changes to dpcd_set_link_settings calls for this workaround.
Do not need to revert the entire change since it only affects patched
case
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: David Galiffi <David.Galiffi@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues on detect_dp function as suggested by
checkpatch.pl.
CHECK: Lines should not end with a '('
WARNING: Missing a blank line after declarations
WARNING: line over 80 characters
CHECK: Alignment should match open parenthesis
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Coding style clean up on enable_link_dp function as suggested by
checkpatch.pl:
CHECK: Lines should not end with a '('
WARNING: line over 80 characters
WARNING: suspect code indent for conditional statements (8, 24)
CHECK: braces {} should be used on all arms of this statement
ERROR: else should follow close brace '}'
CHECK: Comparison to NULL could be written
"link->preferred_training_settings.fec_enable"
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is freeing the wrong variable so it will crash. It should be
freeing "*dmub" instead of "dmub".
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are multiple statements that are indented incorrectly. Add
in the missing tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:
In function hubp21_set_vm_system_aperture_settings:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:343:23:
warning: variable mc_vm_apt_default set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when changing display clock, SMU need to use power up DFS and use
DENTIST to ramp DFS DID to switch target frequency before switching back
to bypass.
[How]
fixed the minimum display clock to 100MHz, it's W/A the same with PCO.
Signed-off-by: Yu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System will crash when trying to access local sink in
core_link_enable_stream in MST case.
[How]
Access patches directly from stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow sometimes occurs during transition into MPO with stutter
enabled.
[How]
When transitioning into MPO, disable stutter. Re-enable stutter within
one frame.
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently clock table struct is very far down in the bounding box struct
making it hard to find while debugging, especially when using the
dal3dbgext.
[HOW]
Move it up so it is the first struct defined, and therefore much easier
to find and access.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some display configuration like 1080P monitor playing a 1080P video,
if user use ALT+F4 to exit Movie and TV, there is a chance clocks are
same only water mark changed. Current clock optimization machanism will
result in water mark keeps high after exit Movie and TV app.
[How]
Return if watermark need to be optimized when doing program watermark,
perform the optimization after.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to assign surface size rather than viewport size for surface size
dml variable.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update TTU properly if DRAMClockChangeWatermark changes. If
TTU < DRAMClockChangeWatermark, we pstate won't be allowed and we will
hang in some PSR cases.
[How]
Update TTU if DramClockChangeWatermark value increases (only if TTU was
dependent on the watermark value on the DRAMClockChangeWatermark value
in the first place).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
RV2 and variants are indistinguishable by hw internal rev alone, need to
be distinguishable in order to correctly set max vlevel. Previous
detection change incorrectly checked for hw internal rev.
[HOW]
Use pci revision to check if RV2 or low power variant Correct a few
overlapping ASICREV range checks
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Add infrastructure to enable and disable PSR on DMCUB.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dcn20_populate_dml_pipes_from_context to correctly handle odm
when no surface is provided.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DalMPVisualConfirm does not support FreeSync 2 ARGB2101010 which causes
black visual confirm bar when playing HDR video on FreeSync 2 display in
full screen mode
[How]
Added pink color for DalMPVisualConfirm on FreeSync 2 ARGB2101010
surface
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern was link level but the whole
asic should be affected.
[How]
- change old link flag to dc level
- new bit in dc->work_arounds set by DM
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some displays clear ignore MSA bit on mode change, which cause
blackscreen when programming variable vtotals. Ignore MSA bit needs
programming needs to be delayed or re-set to be retained.
[How]
Create patch to delay programming ignore MSA bit after unblanking
stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A software workaround is required for all vendor-built cards on platform.
[How]
When performing DP link training, we must send TPS1 before DPCD:100h is
written with the proper bit rate value. This change must be applies in
ALL cases when LT happens.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Not programming dto with same values causes test failures in DCN2 diags
DPP tests.
[HOW]
This reverts commit 1b53e73323.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently DAL programs negative slope for the last point of output
transfer function curve.
[How]
Applying a check for the last PWL point for RGB values not to be
smaller than previous. If smaller, initialize the last point values
to a sum of previous PWL value and previous PWL delta;
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some structures and functions meant only to be used in the
scope of that single rn_clk_mgr c file.
[How]
Make structs and funcs static if only meant to be used within
rn_clk_mgr
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make panel backlight and power on/off functions into
hardware specific function pointers
[How]
Add function pointers for panel related hw functions
- is_panel_powered_on
- is_panel_backlight_on
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Add optimization to allow pstate change support when all displays
are off in DCN2.
[How]
Add clk_mgr_helper_get_active_plane_cnt() to sum plane_count for all
valid stream_status[]. If plane_count is 0, then there are no active
or virtual streams present. Use plane_count == 0 as extra condition to
enable p_state_change_support in dcn2_update_clocks().
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
According to HW team, PG is dropped for NV12, but programming
the registers will still cause power to be consumed, so don't
program for NV12.
[How]
Set function pointer to NULL if NV12
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bugs occur when TX interrupt comes in when no USB-C on board.
[How]
Check PHY for USB-C before enabling TX interrupt in DMCU FW.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently there is a minor error in scaling filter coefficients
caused by truncation to fit the HW registers.This error accummulates
with increased taps, but has gone unnoticed due to vast majority of
scaling being done with only 4 taps.
Scaling filters are now updated using HW team's filter generator
which has quantization error minimization built in.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since the i2c payload allocation can fail need to check return codes
[How]
Clean up i2c payload allocations and check for errors
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
core_link_read_dpcd() will invoke dm_helpers_dp_read_dpcd(),
which needs to read dpcd info with the help of aconnector.
If aconnector (dc->links[i]->prev) is NULL, then dpcd status
cannot be read.
As a result, dpcd read fails and a line of error will be
printed out in dmesg.log as:
"*ERROR* Failed to found connector for link!"
[How]
Make sure that aconnector (dc->links[i]->prev) is not NULL,
then read dpcd status.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Joseph Gravenor <Joseph.Gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:980:36:
warning: address of 'sink->edid_caps.panel_patch.skip_scdc_overwrite'
will always evaluate to 'true' [-Wpointer-bool-conversion]
if (&sink->edid_caps.panel_patch.skip_scdc_overwrite)
~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
1 warning generated.
This is probably not what was intended so remove the address of
operator, which matches how skip_scdc_overwrite is handled in the rest
of the driver.
While we're here, drop an extra newline after this if block.
Fixes: a760fc1bff ("drm/amd/display: add monitor patch to disable SCDC read/write")
Link: https://github.com/ClangBuiltLinux/linux/issues/879
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's used by more than just DCN2.0. Fixes missing symbol when
amdgpu is built without DCN support.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to cover dcn2.x related headers.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:
In function dcn10_post_unlock_program_front_end:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2623:29:
warning: variable stream_status set but not used [-Wunused-but-set-variable]
commit bbf5f6c3f8 ("drm/amd/display: Split program front end part that occur outside lock")
involved this unused variable.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver needs to know PSR state.
[How]
Use GPINT to call to firmware and get psr state.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
customer issue: found that for their specific panel, EDID register space
being overwritten during SCDC read write
[how]
customer accepted HDMI 2 features not working - disabled SCDC read/write
as well as HDMI 2 in general based on monitor patch
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm scaling calculations are only done when adding initial
odm pipe. Any scaling re-calculations will mess up odm because of this.
This change resolves the problem by updating scaling split logic to
handle odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
