[Why]
To compare the crc of the framebuffer data at input of
display pipeline with the crc of the otg, we need to
disable pixel formatter's dynamic expansion feature during
crc capture and keep it enable in the normal operation.
[HOW]
Expose a new interface in DM and dc for pixel formatter
(fmt dynamic bitdepth expansion control). Interface control
the FMT_DYNAMIC_EXP_EN bit, during crc capture keep
it disabled.
Signed-off-by: Robin Singh <robin.singh@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
-Colorspace: Expose different prop values for DP vs. HDMI (Gwan-gyeong Mun)
-fourcc: Add DRM_FORMAT_MOD_ARM_16X16_BLOCK_U_INTERLEAVED (Raymond)
-not_actually: s/ENOTSUPP/EOPNOTSUPP/ in drm_edid and drm_mipi_dbi. This should
not reach userspace, but adding here to specifically call that out (Daniel)
-i810: Prevent underflow in dispatch ioctls (Dan)
-komeda: Add ACLK sysfs attribute (Mihail)
-v3d: Allow userspace to clean up after render jobs (Iago)
Cross-subsystem Changes:
-MAINTAINERS:
-Add Alyssa & Steven as panfrost reviewers (Rob)
-Add Jernej as DE2 reviewer (Maxime)
-Add Chen-Yu as Allwinner maintainer (Maxime)
-staging: Make some stack arrays static const (Colin)
Core Changes:
-ttm: Allow drivers to specify their vma manager (to use gem mgr) (Gerd)
-docs: Various fixes in connector/encoder/bridge docs (Daniel, Lyude, Laurent)
-connector: Allow more than 3 possible encoders for a connector (José)
-dp_cec: Allow a connector to be associated with a cec device (Dariusz)
-various: Fix some compile/sparse warnings (Ville)
-mm: Ensure mm node removals are properly serialised (Chris)
-panel: Specify the type of panel for drm_panels for later use (Laurent)
-panel: Use drm_panel_init to init device and funcs (Laurent)
-mst: Refactors and cleanups in anticipation of suspend/resume support (Lyude)
-vram:
-Add lazy unmapping for gem bo's (Thomas)
-Unify and rationalize vram mm and gem vram (Thomas)
-Expose vmap and vunmap for gem vram objects (Thomas)
-Allow objects to be pinned at the top of vram to avoid fragmentation (Thomas)
Driver Changes:
-various: Include drm_bridge.h instead of relying on drm_crtc.h (Boris)
-ast/mgag200: Refactor show_cursor(), move cursor to top of video mem (Thomas)
-komeda:
-Add error event printing (behind CONFIG) and reg dump support (Lowry)
-Add suspend/resume support (Lowry)
-Workaround D71 shadow registers not flushing on disable (Lowry)
-meson: Add suspend/resume support (Neil)
-omap: Miscellaneous refactors and improvements (Tomi/Jyri)
-panfrost/shmem: Silence lockdep by using mutex_trylock (Rob)
-panfrost: Miscellaneous small fixes (Rob/Steven)
-sti: Fix warnings (Benjamin/Linus)
-sun4i:
-Add vcc-dsi regulator to sun6i_mipi_dsi (Jagan)
-A few patches to figure out the DRQ/start delay calc on dsi (Jagan/Icenowy)
-virtio:
-Add module param to switch resource reuse workaround on/off (Gerd)
-Avoid calling vmexit while holding spinlock (Gerd)
-Use gem shmem helpers instead of ttm (Gerd)
-Accommodate command buffer allocations too big for cma (David)
Cc: Rob Herring <robh@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Raymond Smith <raymond.smith@arm.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mihail Atanassov <Mihail.Atanassov@arm.com>
Cc: Lowry Li <Lowry.Li@arm.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Iago Toral Quiroga <itoral@igalia.com>
Cc: David Riley <davidriley@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHF6rntfJ3enn8gh8cywAJXLcr3kFAl2d9h8ACgkQcywAJXLc
r3ms5gf9HIFpqwJ16CqaRukSnpcBcDoYUM8DGrOic+vw2bw14BQwFqvEOqrCkKL4
V6h/OCJlNFPtOcc1LvU/jeXxYf4AQWh/2qZeg+oee7HAGX5x8Y3f08GsEjO8+55t
QvSVxCKVti04M1ErPRfKrM7KPVE+IC+KdY26nO8Bf5zDGeCAkiPIDrdh2aZGMRdC
Eer0DJ96cgWW9LrhseCdj5nKwcR78DlbWa79zuPAss4LaBBbXqThNXYYzg/mZMKB
+VYgzs48tGYKK1NXXJ6biVI3brHrM52bqv5JpIncD5HepF1oIartWOMnbAO7MAqh
h/tgJWxL+4bnl9aqY87by1BtyVgl3w==
=kaOE
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-10-09-2' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.5:
UAPI Changes:
-Colorspace: Expose different prop values for DP vs. HDMI (Gwan-gyeong Mun)
-fourcc: Add DRM_FORMAT_MOD_ARM_16X16_BLOCK_U_INTERLEAVED (Raymond)
-not_actually: s/ENOTSUPP/EOPNOTSUPP/ in drm_edid and drm_mipi_dbi. This should
not reach userspace, but adding here to specifically call that out (Daniel)
-i810: Prevent underflow in dispatch ioctls (Dan)
-komeda: Add ACLK sysfs attribute (Mihail)
-v3d: Allow userspace to clean up after render jobs (Iago)
Cross-subsystem Changes:
-MAINTAINERS:
-Add Alyssa & Steven as panfrost reviewers (Rob)
-Add Jernej as DE2 reviewer (Maxime)
-Add Chen-Yu as Allwinner maintainer (Maxime)
-staging: Make some stack arrays static const (Colin)
Core Changes:
-ttm: Allow drivers to specify their vma manager (to use gem mgr) (Gerd)
-docs: Various fixes in connector/encoder/bridge docs (Daniel, Lyude, Laurent)
-connector: Allow more than 3 possible encoders for a connector (José)
-dp_cec: Allow a connector to be associated with a cec device (Dariusz)
-various: Fix some compile/sparse warnings (Ville)
-mm: Ensure mm node removals are properly serialised (Chris)
-panel: Specify the type of panel for drm_panels for later use (Laurent)
-panel: Use drm_panel_init to init device and funcs (Laurent)
-mst: Refactors and cleanups in anticipation of suspend/resume support (Lyude)
-vram:
-Add lazy unmapping for gem bo's (Thomas)
-Unify and rationalize vram mm and gem vram (Thomas)
-Expose vmap and vunmap for gem vram objects (Thomas)
-Allow objects to be pinned at the top of vram to avoid fragmentation (Thomas)
Driver Changes:
-various: Include drm_bridge.h instead of relying on drm_crtc.h (Boris)
-ast/mgag200: Refactor show_cursor(), move cursor to top of video mem (Thomas)
-komeda:
-Add error event printing (behind CONFIG) and reg dump support (Lowry)
-Add suspend/resume support (Lowry)
-Workaround D71 shadow registers not flushing on disable (Lowry)
-meson: Add suspend/resume support (Neil)
-omap: Miscellaneous refactors and improvements (Tomi/Jyri)
-panfrost/shmem: Silence lockdep by using mutex_trylock (Rob)
-panfrost: Miscellaneous small fixes (Rob/Steven)
-sti: Fix warnings (Benjamin/Linus)
-sun4i:
-Add vcc-dsi regulator to sun6i_mipi_dsi (Jagan)
-A few patches to figure out the DRQ/start delay calc on dsi (Jagan/Icenowy)
-virtio:
-Add module param to switch resource reuse workaround on/off (Gerd)
-Avoid calling vmexit while holding spinlock (Gerd)
-Use gem shmem helpers instead of ttm (Gerd)
-Accommodate command buffer allocations too big for cma (David)
Cc: Rob Herring <robh@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Raymond Smith <raymond.smith@arm.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mihail Atanassov <Mihail.Atanassov@arm.com>
Cc: Lowry Li <Lowry.Li@arm.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Iago Toral Quiroga <itoral@igalia.com>
Cc: David Riley <davidriley@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 10 Oct 2019 01:00:47 AM AEST
# gpg: using RSA key 732C002572DCAF79
# gpg: Can't check signature: public key not found
# Conflicts:
# drivers/gpu/drm/i915/gem/i915_gem_execbuffer.c
# drivers/gpu/drm/i915/i915_drv.c
# drivers/gpu/drm/i915/i915_gem.c
# drivers/gpu/drm/i915/i915_gem_gtt.c
# drivers/gpu/drm/i915/i915_vma.c
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009150825.GA227673@art_vandelay
p and g are switched in 'amdpgu_dm'
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix sparse warnings:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_hdcp.c:32:6: warning: symbol 'lp_write_i2c' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_hdcp.c:42:6: warning: symbol 'lp_read_i2c' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_hdcp.c:52:6: warning: symbol 'lp_write_dpcd' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_hdcp.c:59:6: warning: symbol 'lp_read_dpcd' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We haven't done any backmerge for a while due to the merge window, and it
starts to become an issue for komeda. Let's bring 5.4-rc1 in.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
We are supposed to be atomic after all. We'll need this in a moment for
the next commit.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kfree() checks this automatically.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, every single piece of code in amdgpu that loops through
connectors does it incorrectly and doesn't use the proper list iteration
helpers, drm_connector_list_iter_begin() and
drm_connector_list_iter_end(). Yeesh.
So, do that.
Cc: Juston Li <juston.li@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since we're going to be reprobing the entire topology state on resume
now using sideband transactions, we need to ensure that we actually have
short HPD irqs enabled before calling drm_dp_mst_topology_mgr_resume().
So, do that.
Changes since v4:
* Fix typo in comments
Cc: Juston Li <juston.li@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We had a couple of missing definitions and formatting errors.
v2: Fix 'notifying' type
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without CONFIG_DEBUG_FS, we get a warning for an unused
variable:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:6020:33: error: unused variable 'source' [-Werror,-Wunused-variable]
Hide the variable in an #ifdef like its only users.
Fixes: 14b2584636 ("drm/amd/display: add functionality to grab DPRX CRC entries.")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Laptops with AMD APU doesn't restore display backlight brightness after
system resume.
This issue started when DC was introduced.
Let's use BL_CORE_SUSPENDRESUME so the backlight core calls
update_status callback after system resume to restore the backlight
level.
Tested on Dell Inspiron 3180 (Stoney Ridge) and Dell Latitude 5495
(Raven Ridge).
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We don't support HDCP for pre RAVEN asics
[How]
Check if we are RAVEN+. Use this to attach the content_protection
property, this way usermode can't try to enable HDCP on pre DCN asics.
Also we need to update the module on hpd so guard it aswell
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to use HW state to set content protection to ENABLED.
This way we know that the link is encrypted from the HW side
[How]
Create a workqueue that queries the HW every ~2seconds, and sets it to
ENABLED or DESIRED based on the result from the hardware
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This is needed for DP as DP can send us info using irq.
[How]
Check if irq bit is set on short pulse and call the
function that handles cpirq in amdgpu_dm_hdcp
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to manage the content protection property changes for
different usecase, once cp is DESIRED we need to maintain the
ENABLED/DESIRED status for different cases.
[How]
1. Attach the content_protection property
2. HDCP enable (UNDESIRED -> DESIRED)
call into the module with the correct parameters to start
hdcp. Set cp to ENABLED
3. HDCP disable (ENABLED -> UNDESIRED)
Call the module to disable hdcp.
3. Handle Special cases (Hotplug, S3, headless S3, DPMS)
If already ENABLED: set to DESIRED on unplug/suspend/dpms,
and disable hdcp
Then on plugin/resume/dpms: enable HDCP
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need this to enable HDCP on linux, as we need events to interact
with the hdcp module
[How]
Add work queue to display manager and handle the creation and destruction
of the queue
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to read and write specific i2c and dpcd messages.
[How]
Created static functions for packing the dpcd and i2c messages for hdcp.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to interact with the hdcp module from the DM, the module
has to be interacted with in terms of events
[How]
Create the files needed for linux hdcp. These files manage the events
needed for the dm to interact with the hdcp module.
We use the kernel work queue to process the events needed for
the module
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A lot of the time, the backlight characteristic curve maps min backlight
to a non-zero value.
But there are cases where we want the curve to intersect at 0.
In this scenario even if OS never asks to set 0% backlight, the ABM
reduction can result in backlight being lowered close to 0.
This particularly can cause problems in some LED drivers, and in
general just looks like backlight is completely off.
[How]
Add default cap to disallow backlight from dropping below 1%
even after ABM reduction is applied.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without CONFIG_DEBUG_FS, we get a warning for an unused
variable:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:6020:33: error: unused variable 'source' [-Werror,-Wunused-variable]
Hide the variable in an #ifdef like its only users.
Fixes: 14b2584636 ("drm/amd/display: add functionality to grab DPRX CRC entries.")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-fixes-5.4-2019-09-25:
amdgpu:
- Fix a 64 bit divide
- Prevent a memory leak in a failure case in dc
- Load proper gfx firmware on navi14 variants
drm-fixes-5.4-2019-09-19:
amdgpu:
- Add more navi12 and navi14 PCI ids
- Misc fixes for renoir
- Fix bandwidth issues with multiple displays on vega20
- Support for Dali
- Fix a possible oops with KFD on hawaii
- Fix for backlight level after resume on some APUs
- Other misc fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925213500.3490-1-alexander.deucher@amd.com
- Some cleanups and fixes in the self-refresh helpers
- Some cleanups and fixes in the atomic helpers
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXYjuIAAKCRDj7w1vZxhR
xfNKAP9dlMLleLnjvAnCpI/Q2YZAktGCC9mIvqSzXJz52mwXNQEA5avYLerwa2+J
P5xmO7mr2/9gzeeeWE1xaufQwZnYrwY=
=Z99W
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2019-09-23' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
- Multiple panfrost fixes for regulator support and page fault handling
- Some cleanups and fixes in the self-refresh helpers
- Some cleanups and fixes in the atomic helpers
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923160946.nvaqiw5j7fpcdhc7@gilmour
It's the only flag anyone actually cares about. Plus if we're unlucky,
the atomic ioctl might need a different flag for async flips. So
better to abstract this away from the uapi a bit.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190903190642.32588-3-daniel.vetter@ffwll.ch
Laptops with AMD APU doesn't restore display backlight brightness after
system resume.
This issue started when DC was introduced.
Let's use BL_CORE_SUSPENDRESUME so the backlight core calls
update_status callback after system resume to restore the backlight
level.
Tested on Dell Inspiron 3180 (Stoney Ridge) and Dell Latitude 5495
(Raven Ridge).
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With stutter mode enabled, NMI prints frequently.
Disable stutter for the moment because NMI warning storm, and will
enable it back till the issue is addressed
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Separating the hardware initialization from the creation of the
dc structures gives greater flexibility to the dm to override
options for debugging.
[How]
Move the hardware initialization call to a new function,
dc_hardware_init. No functional change is intended.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Even if YUV420 is available for video mode, YUV444 is still
automatically selected. This poses a problem for compliance tests.
[How]
Add a per-connector debugfs entry "force_yuv420_output" to force
selection of YUV420 mode.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently we restrict the number of encoders that can be linked to
a connector to 3, increase it to match the maximum number of encoders
that can be initialized(32).
To more effiently do that lets switch from an array of encoder ids to
bitmask.
v2: Fixing missed return on amdgpu_dm_connector_to_encoder()
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: dri-devel@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190913232857.389834-2-jose.souza@intel.com
It is fine for displays without audio functionality to not provide
any SAD block in their EDID. Do not log an error in that case,
just return quietly.
This fixes half of bug fdo#107825:
https://bugs.freedesktop.org/show_bug.cgi?id=107825
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Edid Utility wishes to include DSC module from driver instead
of doing it's own logic which will need to be updated every time
someone modifies the driver logic.
[How]
Modify some functions such that we dont need to pass the entire
DC structure as parameter.
-Remove DC inclusion from module.
-Filter out problematic types and inclusions
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New behaviour will track global updates and update any hw that isn't
related to current stream being updated.
This should fix any issues caused by pipe split pipes being taken
by other streams.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We should not allocate payloads if the link is lost until the link is retrained.
Some displays require this.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With stutter mode enabled, NMI prints frequently.
Disable stutter for the moment because NMI warning storm, and will
enable it back till the issue is addressed
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-next-5.4-2019-08-30:
amdgpu:
- Add DC support for Renoir
- Add some GPUVM hw bug workarounds
- add support for the smu11 i2c controller
- GPU reset vram lost bug fixes
- Navi1x powergating fixes
- Navi12 power fixes
- Renoir power fixes
- Misc bug fixes and cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830212650.5055-1-alexander.deucher@amd.com
Hook up renoir support to KMS.
v2: squash in "Fixes for Renoir in amdgpu_dm"
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since reservation_object_wait_timeout_rcu is called with
interruptable set to false it's wrong to say
'or interrupted' in the error message.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pass the connector info to the CEC adapter. This makes it possible
to associate the CEC adapter with the corresponding drm connector.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20190814104520.6001-2-darekm@google.com
drm-next-5.4-2019-08-23:
amdgpu:
- Enable power features on Navi12
- Enable power features on Arcturus
- RAS updates
- Initial Renoir APU support
- Enable power featyres on Renoir
- DC gamma fixes
- DCN2 fixes
- GPU reset support for Picasso
- Misc cleanups and fixes
scheduler:
- Possible race fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823202620.3870-1-alexander.deucher@amd.com
DRM provides drm_dp_mst_dump_topology, which prints
useful information about MST devices
Hook this up to a debugfs file named amdgpu_mst_topology
Signed-off-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a dcfeaturemask flag for mclk switching. Disable by default;
enable once the feature has seen more testing.
Set amdgpu.dcfeaturemask=2 on the kernel command line in grub
to enable this.
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In create_stream_for_sink, check for SST DP connectors
Parse DSC caps to DC format, then, if DSC is supported,
compute the config
DSC hardware will be programmed by dc_commit_state
Tested-by: Mikita Lipski <Mikita.Lipski@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to ensure that we're holding the lock on the CRTC when setting
the CRC source since we're modifying the CRTC state directly.
We also need to wait for any outstanding non-blocking commits to finish
so they aren't reading state that's potentially being modified -
non-blocking commits don't hold the CRTC lock while doing commit tail
work.
[How]
Lock the CRTC using its mutex. While holding the lock check if there's
any commit active on the CRTC - if there is, it's non-blocking and
we should wait until it's finished by waiting for hw_done to be
signaled since that's the last point where we touch CRTC state.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Calling amdgpu_dm_crtc_set_crc_source in amdgpu_dm directly has the
consequence of adding additional vblank references or starting DPRX
CRC capture more than once without calling stop first.
Vblank references for CRC capture should be managed entirely by opening
and closing the CRC file from userspace.
Stream state also shouldn't be required on the CRC so we can close the
file after the CRTC has been disabled.
[How]
Do DC programming required for configuring CRC capture separately from
setting the source. Whenever we re-enable or reset a CRC this
programming should be reapplied.
CRC vblank reference handling in amdgpu_dm can be entirely dropped after
this.
Stream state also no longer needs to be required since we can just defer
the programming to when the stream is actually enabled.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change is a refactor in preparation for adding locking and removing
the requirement for a stream state on the CRTC for enabling CRC capture
to fix igt@kms_plane_multiple@* warnings.
[How]
We can get the aux by finding the matching connector for the CRTC
with the assumption that we're not doing cloning.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The call to drm_crtc_vblank_get can fail if vblank is disabled and
we try to increment the reference.
Since drm_crtc_vblank_get internally drops the reference when it fails
it means the subsequent drm_crtc_vblank_put(...) when closing the file
drops a zero reference.
This was found via igt@kms_plane@pixel-format-pipe-A-planes.
[How]
Check the return code and return it on failure.
We wouldn't have been able to enable CRC reading anyway since vblank
wasn't enabled.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The only place where state->max_bpc is updated on the connector is
at the start of atomic check during drm_atomic_connector_check. It
isn't updated when adding the connectors to the atomic state after
the fact. It also doesn't necessarily reflect the right value when
called in amdgpu during mode validation outside of atomic check.
This can cause the wrong bpc to be used even if the max_requested_bpc
is the correct value.
[How]
Don't rely on state->max_bpc reflecting the real bpc value and just
do the min(...) based on display info bpc and max_requested_bpc.
Fixes: 01933ba42d ("drm/amd/display: Use current connector state if NULL when checking bpc")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dma-buf: add reservation_object_fences helper, relax
reservation_object_add_shared_fence, remove
reservation_object seq number (and then
restored)
- dma-fence: Shrinkage of the dma_fence structure,
Merge dma_fence_signal and dma_fence_signal_locked,
Store the timestamp in struct dma_fence in a union with
cb_list
Driver Changes:
- More dt-bindings YAML conversions
- More removal of drmP.h includes
- dw-hdmi: Support get_eld and various i2s improvements
- gm12u320: Few fixes
- meson: Global cleanup
- panfrost: Few refactors, Support for GPU heap allocations
- sun4i: Support for DDC enable GPIO
- New panels: TI nspire, NEC NL8048HL11, LG Philips LB035Q02,
Sharp LS037V7DW01, Sony ACX565AKM, Toppoly TD028TTEC1
Toppoly TD043MTEA1
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXVqvpwAKCRDj7w1vZxhR
xa3RAQDzAnt5zeesAxX4XhRJzHoCEwj2PJj9Re6xMJ9PlcfcvwD+OS+bcB6jfiXV
Ug9IBd/DqjlmD9G9MxFxfSV946rksAw=
=8uv4
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-08-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.4:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dma-buf: add reservation_object_fences helper, relax
reservation_object_add_shared_fence, remove
reservation_object seq number (and then
restored)
- dma-fence: Shrinkage of the dma_fence structure,
Merge dma_fence_signal and dma_fence_signal_locked,
Store the timestamp in struct dma_fence in a union with
cb_list
Driver Changes:
- More dt-bindings YAML conversions
- More removal of drmP.h includes
- dw-hdmi: Support get_eld and various i2s improvements
- gm12u320: Few fixes
- meson: Global cleanup
- panfrost: Few refactors, Support for GPU heap allocations
- sun4i: Support for DDC enable GPIO
- New panels: TI nspire, NEC NL8048HL11, LG Philips LB035Q02,
Sharp LS037V7DW01, Sony ACX565AKM, Toppoly TD028TTEC1
Toppoly TD043MTEA1
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: fixup dma_resv rename fallout]
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190819141923.7l2adietcr2pioct@flea
[Why]
DCN10 performs color processing before MPC combination, causes color
shift in RGB colorspaces when positive brightness offset is applied
However, YCbCr is still unfixed and remains disabled
[How]
Add layerIndex to dc_plane_state and dc_plane_info structs
Re-enable MPO when brightness is adjusted and colorspace is not YCbCr
Set rear plane's brightness offset to 0 when front plane visible
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Be more consistent with the naming of the other DMA-buf objects.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/323401/
drm-next-5.4-2019-08-09:
Same as drm-next-5.4-2019-08-06, but with the
readq/writeq stuff fixed and 5.3-rc3 backmerged.
amdgpu:
- Add navi14 support
- Add navi12 support
- Add Arcturus support
- Enable mclk DPM for Navi
- Misc DC display fixes
- Add perfmon support for DF
- Add scatter/gather display support for Raven
- Improve SMU handling for GPU reset
- RAS support for GFX
- Drop last of drmP.h
- Add support for wiping memory on buffer release
- Allow cursor async updates for fb swaps
- Misc fixes and cleanups
amdkfd:
- Add navi14 support
- Add navi12 support
- Add Arcturus support
- CWSR trap handlers updates for gfx9, 10
- Drop last of drmP.h
- Update MAINTAINERS
radeon:
- Misc fixes and cleanups
- Make kexec more reliable by tearing down the GPU
ttm:
- Add release_notify callback
uapi:
- Add wipe memory on release flag for buffer creation
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: resolved conflicts with ttm resv moving]
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190809184807.3381-1-alexander.deucher@amd.com
[Why]
Underflow can occur in the case where we change buffer pitch, DCC state,
rotation or mirroring for a plane while also performing an immediate
flip. It can also generate a p-state warning stack trace on DCN1 which
is typically observed during the cursor handler pipe locking because of
how frequent cursor updates can occur.
[How]
Store the update type on each CRTC - every plane will have access to
the CRTC state if it's flipping. If the update type is not
UPDATE_TYPE_FAST then the immediate flip should be disallowed.
No changes to the target vblank sequencing need to be done, we just
need to ensure that the surface registers do a double buffered update.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pitch, DCC, rotation and mirroring can result in updates that are not
UPDATE_TYPE_FAST but UPDATE_TYPE_MED instead. DC needs dc_plane_info
and dc_plane_size to make this determination and we aren't currently
passing this into DC during atomic check.
Underflow (visible or non-visible) can occur if we don't validate this
correctly. This also will generally trigger p-state warnings, typically
via the cursor handler when locking.
[How]
Get the framebuffer tiling flags and generate the required structures
for DC in dm_determine_update_type_for_commit.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing navi12 asic ids.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DRM private objects have no hw_done/flip_done fencing mechanism on their
own and cannot be used to sequence commits accordingly.
When issuing commits that don't touch the same set of hardware resources
like page-flips on different CRTCs we can run into the issue below
because of this:
1. Client requests non-blocking Commit #1, has a new dc_state #1,
state is swapped, commit tail is deferred to work queue
2. Client requests non-blocking Commit #2, has a new dc_state #2,
state is swapped, commit tail is deferred to work queue
3. Commit #2 work starts, commit tail finishes,
atomic state is cleared, dc_state #1 is freed
4. Commit #1 work starts,
commit tail encounters null pointer deref on dc_state #1
In order to change the DC state as in the private object we need to
ensure that we wait for all outstanding commits to finish and that
any other pending commits must wait for the current one to finish as
well.
We do this for MEDIUM and FULL updates. But not for FAST updates, nor
would we want to since it would cause stuttering from the delays.
FAST updates that go through dm_determine_update_type_for_commit always
create a new dc_state and lock the DRM private object if there are
any changed planes.
We need the old state to validate, but we don't actually need the new
state here.
[How]
If the commit isn't a full update then the use after free can be
resolved by simply discarding the new state entirely and retaining
the existing one instead.
With this change the sequence above can be reexamined. Commit #2 will
still free Commit #1's reference, but before this happens we actually
added an additional reference as part of Commit #2.
If an update comes in during this that needs to change the dc_state
it will need to wait on Commit #1 and Commit #2 to finish. Then it'll
swap the state, finish the work in commit tail and drop the last
reference on Commit #2's dc_state.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204181
Fixes: 004b3938e6 ("drm/amd/display: Check scaling info when determing update type")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
By passing through the dm_determine_update_type_for_commit for atomic
commits that can be done asynchronously we are incurring a
performance penalty by locking access to the global private object
and holding that access until the end of the programming sequence.
This is also allocating a new large dc_state on every access in addition
to retaining all the references on each stream and plane until the end
of the programming sequence.
[How]
Shift the determination for async update before validation. Return early
if it's going to be an async update.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We previously allowed framebuffer swaps as async updates for cursor
planes but had to disable them due to a bug in DRM with async update
handling and incorrect ref counting. The check to block framebuffer
swaps has been added to DRM for a while now, so this check is redundant.
The real fix that allows this to properly in DRM has also finally been
merged and is getting backported into stable branches, so dropping
this now seems to be the right time to do so.
[How]
Drop the redundant check for old_fb != new_fb.
With the proper fix in DRM, this should also fix some cursor stuttering
issues with xf86-video-amdgpu since it double buffers the cursor.
IGT tests that swap framebuffers (-varying-size for example) should
also pass again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using a static int array will cause errors if the given dm_pp_clk_type
is out-of-bounds. For robustness, use a switch table, with a default
case to handle all invalid values.
v2: 0 is a valid clock type for smu_clk_type. Return SMU_CLK_COUNT
instead on invalid mapping.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang warns:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_pp_smu.c:336:8:
warning: implicit conversion from enumeration type 'enum smu_clk_type'
to different enumeration type 'enum amd_pp_clock_type'
[-Wenum-conversion]
dc_to_smu_clock_type(clk_type),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_pp_smu.c:421:14:
warning: implicit conversion from enumeration type 'enum
amd_pp_clock_type' to different enumeration type 'enum smu_clk_type'
[-Wenum-conversion]
dc_to_pp_clock_type(clk_type),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
There are functions to properly convert between all of these types, use
them so there are no longer any warnings.
Fixes: a43913ea50 ("drm/amd/powerplay: add function get_clock_by_type_with_latency for navi10")
Fixes: e5e4e22391 ("drm/amd/powerplay: add interface to get clock by type with latency for display (v2)")
Link: https://github.com/ClangBuiltLinux/linux/issues/586
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
provide the interface for DAL to disable uclk switch on navi10.
in this case, the uclk will be fixed to maximum.
this is a workaround when display configuration causes underflow issue.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add restriction to dissallow GTT domain if the relevant BO
doesn't have USWC flag set to avoid the APU hang scenario.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
enables gpu_vm_support in dm and adds
AMDGPU_GEM_DOMAIN_GTT as supported domain
v2:
Move BO placement logic into amdgpu_display_supported_domains
v3:
Use amdgpu_bo_validate_uswc in amdgpu_display_supported_domains.
v4:
amdgpu_bo_validate_uswc moved to sepperate patch.
Signed-off-by: Shirish S <shirish.s@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement late_register and early_unregister hooks for MST connectors.
Call drm helpers for MST connector registration, which registers the
AUX devices.
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190723232808.28128-10-sunpeng.li@amd.com
Set the connector's kernel device as the parent for the aux kernel
device. This allows udev rules to access connector attributes when
creating symlinks to aux devices.
For example, the following udev rule:
SUBSYSTEM=="drm_dp_aux_dev", SUBSYSTEMS=="drm", ATTRS{edid}=="*",
SYMLINK+="drm_dp_aux/by-name/$id"
Will create the following symlinks using the connector's name:
$ ls /dev/drm_dp_aux/by-name/
card0-DP-1 card0-DP-2 card0-DP-3
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190723232808.28128-6-sunpeng.li@amd.com
Add dual plane dcc programming support for
surfaces.
Removes unions from plane size and dcc params as they
serve no practical purpose only making our code
more convoluted. This results in easy dual plane
dcc and surface size programming.
Temporary diags_dm code is used to handle the interface
change without breaking functionality as a diags change
needs to be applied after this one.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
need to verify the impact of spatial dithering on 8bpc bypass mode.
[How]
added CRC sources and configure dihter option from dc stream.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: Hanghong Ma <Hanghong.Ma@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to check the pipe crc source through debugfs for bypass mode test.
[How]
add implementation of amdgpu_dm_crtc_get_crc_sources and hook into drm_crtc
callback get_crc_sources.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to compare DPRX CRCs with framebuffer CRCs for digital bypass mode.
[How]
Hook into DRM to grab DP receiver CRCs through drm_dp_start_crc.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
not needed for navi14 at the moment.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Workaround for now to avoid underflow.
The uclk switch time should really be bumped up to 404, but doing so
would expose p-state hang issues for higher bandwidth display
configurations.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the clock is already logged, also log the voltage.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The drm_audio_component can be used to give pin ELD notifications
directly to the sound driver. This fixes audio endpoints disappearing
due to missing unsolicited notifications.
[How]
Send the notification via the audio component whenever we enable or
disable audio state on a stream. This matches what i915 does with
their drm_audio_component and what Takashi Iwai's proposed hack for
radeon/amdpgu did.
This is a bit delayed in when the notification actually occurs, however.
We wait until after all the programming is complete rather than sending
the notification mid sequence.
Particular care is needed for the get ELD callback since it can happen
outside the locking and fencing DRM does for atomic commits.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All asics newer than vega10 use client ids, so simplify the
check.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported by smatch:
amdgpu_dm.c:5637 amdgpu_dm_commit_planes() error: we previously assumed 'acrtc_state->stream' could be null
This seems to be checked for null pretty consistently elsewhere.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for the upcoming DRM plane color management properties
we need to correct a lot of wrong behavior and assumptions made for
CRTC color management.
The documentation added by this commit in amdgpu_dm_color explains
how the HW color pipeline works and its limitations with the DRM
interface.
The current implementation does the following wrong:
- Implicit sRGB DGM when no CRTC DGM is set
- Implicit sRGB RGM when no CRTC RGM is set
- No way to specify a non-linear DGM matrix that produces correct output
- No way to specify a correct RGM when a linear DGM is used
We had workarounds for passing kms_color tests but not all of the
behavior we had wrong was covered by these tests (especially when
it comes to non-linear DGM). Testing both DGM and RGM at the same time
isn't something kms_color tests well either.
[How]
The specifics for how color management works in AMDGPU and the new
behavior can be found by reading the documentation added to
amdgpu_dm_color.c from this patch.
All of the incorrect cases from the old implementation have been
addressed for the atomic interface, but there still a few TODOs for
the legacy one.
Note: this does cause regressions for kms_color@pipe-a-ctm-* over HDMI.
The result looks correct from visual inspection but the CRC no longer
matches. For reference, the test was previously doing the following:
linear degamma -> CTM -> sRGB regamma -> RGB to YUV (709) -> ...
Now the test is doing:
linear degamma -> CTM -> linear regamma -> RGB to YUV (709) -> ...
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Current policy assumes virtual DPCD peer device as
an individual MST branch device with 1 input and 1 output.
However this is only true for virtual DP-to-DP peer device.
In general there are three types of virtual DP peer devices.
1. Sink peer device with virtual DPCD.
2. Virtual DP-to-DP Peer device with virtual DPCD.
3. Virtual DP-to-HDMI Protocol Converter Peer Device with
Virtual DPCD.
So we should break the assumption and handle all three types.
[how]
DP-to-DP peer device will have virtual DPCD cap upstream.
Sink peer device will have virtual DPCD on the logical port.
Dp to HDMI protocol converter peer device will have virtual DPCD
on its converter port.
For DSC capable Synaptics non VGA port we workaround by enumerating
a virutal DPCD peer device on its upstream
even if it doesn't have one.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the generic introduction of seamless boot, the display is no
longer blanked upon boot. However, this causes corruption on some
systems that does not lock the memory in the non-secure boot case,
resulting in brief corruption on boot due to garbage being written into
the frame buffer.
[How]
Add a flag, read during DC init, to determine whether display should be
blanked on boot. Default to true.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] dcn20 enable usb-c dp ALT mode in dmcu. There is bug
when enable abm feature which cause system crash. dal team
will debug this bug later.
[HOW] disable dcn abm feature for dcn20.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
during bring up time, before window dc-ppplib interface
design, linux dc use raven dc-pplib interface.
now nvai10 dc-pplib-smu interface is changed and verified
under window, navi10 need its specific dc-pplib-smu
interface. todo: hook set_hard_min_uclk_by_freq,
get_maximum_sustainable_clocks
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We don't want to expose sensitive ASIC information before ASIC release.
[HOW]
Encode the soc_bounding_box in the gpu_info FW (for Linux) and read it
at driver load.
v2: fix warning when CONFIG_DRM_AMD_DC_DCN2_0 is not set (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add callback function get_clock_by_type_with_latency for navi10 asic
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit ebc8c6f18322ad54275997a888ca1731d74b711f.
There are still missing corner cases with cursor interaction and these
fast plane updates on Picasso and Raven2 leading to endless PSTATE
warnings for typical desktop usage depending on the userspace.
This change should be reverted until these issues have been resolved.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110949
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Gj1MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGctkH/0At3+SQPY2JJSy8
i6+TDeytFx9OggeGLPHChRfehkAlvMb/kd34QHnuEvDqUuCAMU6HZQJFKoK9mvFI
sDJVayPGDSqpm+iv8qLpMBPShiCXYVnGZeVfOdv36jUswL0k6wHV1pz4avFkDeZa
1F4pmI6O2XRkNTYQawbUaFkAngWUCBG9ECLnHJnuIY6ohShBvjI4+E2JUaht+8gO
M2h2b9ieddWmjxV3LTKgsK1v+347RljxdZTWnJ62SCDSEVZvsgSA9W2wnebVhBkJ
drSmrFLxNiM+W45mkbUFmQixRSmjv++oRR096fxAnodBxMw0TDxE1RiMQWE6rVvG
N6MC6xA=
=+B0P
-----END PGP SIGNATURE-----
Merge v5.2-rc5 into drm-next
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The memory was set to zero already by a call of the function “kzalloc”.
Thus remove an extra call of the function “memset” for this purpose.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Add code to signal all dma-fences when freed with pending signals.
- Annotate reservation object access in CONFIG_DEBUG_MUTEXES
Core Changes:
- Assorted documentation fixes.
- Use irqsave/restore spinlock to add crc entry.
- Move code around to drm_client, for internal modeset clients.
- Make drm_crtc.h and drm_debugfs.h self-contained.
- Remove drm_fb_helper_connector.
- Add bootsplash to todo.
- Fix lock ordering in pan_display_legacy.
- Support pinning buffers to current location in gem-vram.
- Remove the now unused locking functions from gem-vram.
- Remove the now unused kmap-object argument from vram helpers.
- Stop checking return value of debugfs_create.
- Add atomic encoder enable/disable helpers.
- pass drm_atomic_state to atomic connector check.
- Add atomic support for bridge enable/disable.
- Add self refresh helpers to core.
Driver Changes:
- Add extra delay to make MTP SDM845 work.
- Small fixes to virtio, vkms, sii902x, sii9234, ast, mcde, analogix, rockchip.
- Add zpos and ?BGR8888 support to meson.
- More removals of drm_os_linux and drmP headers for amd, radeon, sti, r128, r128, savage, sis.
- Allow synopsis to unwedge the i2c hdmi bus.
- Add orientation quirks for GPD panels.
- Edid cleanups and fixing handling for edid < 1.2.
- Add runtime pm to stm.
- Handle s/r in dw-hdmi.
- Add hooks for power on/off to dsi for stm.
- Remove virtio dirty tracking code, done in drm core.
- Rework BO handling in ast and mgag200.
-----BEGIN PGP SIGNATURE-----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=4uQX
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add code to signal all dma-fences when freed with pending signals.
- Annotate reservation object access in CONFIG_DEBUG_MUTEXES
Core Changes:
- Assorted documentation fixes.
- Use irqsave/restore spinlock to add crc entry.
- Move code around to drm_client, for internal modeset clients.
- Make drm_crtc.h and drm_debugfs.h self-contained.
- Remove drm_fb_helper_connector.
- Add bootsplash to todo.
- Fix lock ordering in pan_display_legacy.
- Support pinning buffers to current location in gem-vram.
- Remove the now unused locking functions from gem-vram.
- Remove the now unused kmap-object argument from vram helpers.
- Stop checking return value of debugfs_create.
- Add atomic encoder enable/disable helpers.
- pass drm_atomic_state to atomic connector check.
- Add atomic support for bridge enable/disable.
- Add self refresh helpers to core.
Driver Changes:
- Add extra delay to make MTP SDM845 work.
- Small fixes to virtio, vkms, sii902x, sii9234, ast, mcde, analogix, rockchip.
- Add zpos and ?BGR8888 support to meson.
- More removals of drm_os_linux and drmP headers for amd, radeon, sti, r128, r128, savage, sis.
- Allow synopsis to unwedge the i2c hdmi bus.
- Add orientation quirks for GPD panels.
- Edid cleanups and fixing handling for edid < 1.2.
- Add runtime pm to stm.
- Handle s/r in dw-hdmi.
- Add hooks for power on/off to dsi for stm.
- Remove virtio dirty tracking code, done in drm core.
- Rework BO handling in ast and mgag200.
Tiny conflict in drivers/gpu/drm/amd/display/dc/clk_mgr/clk_mgr.c,
needed #include <linux/slab.h> to make it compile.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0e01de30-9797-853c-732f-4a5bd6e61445@linux.intel.com
I missed amdgpu in my connnector_helper_funcs->atomic_check conversion,
which is understandably causing compilation failures.
Fixes: 6f3b62781b ("drm: Convert connector_helper_funcs->atomic_check to accept drm_atomic_state")
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> [for rcar lvds]
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <karolherbst@gmail.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: dri-devel@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190614002713.141340-1-sean@poorly.run
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: hersen wu <hersenxs.wu@amd.com>
Cc: "Leo (Hanghong) Ma" <hanghong.ma@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for the upcoming DRM plane color management properties
we need to correct a lot of wrong behavior and assumptions made for
CRTC color management.
The documentation added by this commit in amdgpu_dm_color explains
how the HW color pipeline works and its limitations with the DRM
interface.
The current implementation does the following wrong:
- Implicit sRGB DGM when no CRTC DGM is set
- Implicit sRGB RGM when no CRTC RGM is set
- No way to specify a non-linear DGM matrix that produces correct output
- No way to specify a correct RGM when a linear DGM is used
We had workarounds for passing kms_color tests but not all of the
behavior we had wrong was covered by these tests (especially when
it comes to non-linear DGM). Testing both DGM and RGM at the same time
isn't something kms_color tests well either.
[How]
The specifics for how color management works in AMDGPU and the new
behavior can be found by reading the documentation added to
amdgpu_dm_color.c from this patch.
All of the incorrect cases from the old implementation have been
addressed for the atomic interface, but there still a few TODOs for
the legacy one.
Note: this does cause regressions for kms_color@pipe-a-ctm-* over HDMI.
The result looks correct from visual inspection but the CRC no longer
matches. For reference, the test was previously doing the following:
linear degamma -> CTM -> sRGB regamma -> RGB to YUV (709) -> ...
Now the test is doing:
linear degamma -> CTM -> linear regamma -> RGB to YUV (709) -> ...
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The module parameter to specify the default ABM level is now defined,
so hook it up in DM.
[How]
On connector reset specify the default level. DC will program this as
part of the modeset since it gets passed onto the stream in
dm_update_crtc_state.
It's only set for eDP connectors, but it doesn't matter if this is
specified for connectors or hardware that doesn't support ABM.
It's DC's responsibility to check that ABM can be set or adjusted, and
DC does check that the DMCU firmware is running and if there's backlight
control available.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever the a modeset is allowed (but not neccessarily required) we
currently recreate all the planes in the state. Most IGT tests and
legacy IOCTLs create atomic commits with this flag set, so the pipes
are often unnecessarily reprogrammed.
Poor performance and stuttering can occur when many of these commits
are frequently issued.
This flag was needed when the appropriate conditions for checking
whether the planes needed a reset were not in place, but
should_reset_plane should cover everything needed now.
[How]
Drop the check for state->allow_modeset in should_reset_plane.
All planes on a CRTC should reset in the following conditions:
- The CRTC needs a modeset
- The CRTC degamma changes
- Planes are added or removed to the CRTC
These conditions are all covered in should_reset_plane.
We still can't drop the format change check in should_reset_plane since
fill_dc_plane_info_and_addr isn't called when validating the state, so
we can't tell if a FULL update is needed or not.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The old logic for checking which output depth to use relied on using
the current connector state rather than the new proposed state. This
was a problem when performing atomic commits since we weren't verifying
it against the incoming max_requested_bpc.
But switching this to only use the new state and not the current state
breaks filtering modes - it'll always assume that the maximum bpc
supported by the display is in use, which will cause certain modes
like 1440p@144Hz to be filtered even when using 8bpc.
[How]
Still use the connector->state if we aren't passed an explicit state.
This will respect the max_bpc the user currently has when filtering
modes.
Also remember to reset the default max_requested_bpc to 8 whenever
connector reset is called to retain old behavior when using the new
property.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110845
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unlike our regular connectors, MST connectors don't start off with
an initial connector state. This causes a NULL pointer dereference to
occur when attaching the bpc property since it tries to modify the
connector state.
We need an initial connector state on the connector to avoid the crash.
[How]
Use our reset helper to allocate an initial state and reset the values
to their defaults. We were already doing this before, just not for
MST connectors.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This will be useful for verifying whether we enter the correct output
color depth from IGT.
[How]
Locks the connector and associated CRTC if available and outputs
the current and maximum output bpc values.
Example:
cat /sys/kernel/debug/dri/0/DP-1/output_bpc
Current: 8
Maximum: 10
v2: Drop unneeded connector status check
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching from vt to desktop with EDID emulation we can receive
an atomic commit such that we have a crtc where mode_changed = true.
During the dm_update_crtc_state disable pass we remove the stream from
the context and free it on the dm_new_crtc_state.
During the enable pass we compare the new provisional stream to the
dm_old_crtc_state->stream and determine that the stream is unchanged
and no scaling has been changed.
Following this, new_crtc_state->mode_changed is then set to false.
The connectors haven't changed and the CRTC active state hasn't changed
so drm_atomic_crtc_needs_modeset returns false, so we jump to
skip_modeset and we hit:
BUG_ON(dm_new_crtc_state->stream == NULL);
...since the old stream is gone from the context and the new stream is
also still NULL.
[How]
Ensure that we still a stream to reuse before checking if we can reuse
the old stream without a full modeset.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop all uses of drmP.h in drm/amd/display/.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-9-sam@ravnborg.org
Drop use of the deprecated drmP.h header file from
all amd header files.
This makes it a more smooth process to get rid of drmP.h
in the .c files.
Added include files and forwards as appropriate.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-7-sam@ravnborg.org
Delete the unused drmP.h from amdgpu.h.
Fix fallout in various files.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-5-sam@ravnborg.org
amdgpu:
- Revert timeline support until KHR is ready
- Various driver reload fixes
- Refactor clock handling in DC
- Aux fixes for DC
- Bandwidth calculation updates for DC
- Fix documentation due to file rename
- RAS fix
- Fix race in late_init
ttm:
- Allow for better forward progress when there is heavy memory contention
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190606032537.6939-1-alexander.deucher@amd.com
These got added back by subsequent merges accidently.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
-----BEGIN PGP SIGNATURE-----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=GrAP
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6c43ffa9-11ff-5354-d772-c20fd4d1e3d9@linux.intel.com
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Calling drm_atomic_set_fb_for_plane() (which gets a reference of the new
fb and put the old fb) is not required, as it's taken care by
drm_mode_cursor_universal() when calling drm_atomic_helper_update_plane().
Cc: <stable@vger.kernel.org> # v4.20+
Fixes: 674e78acae ("drm/amd/display: Add fast path for cursor plane updates")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-3-helen.koike@collabora.com
[Why]
We can issue HDR static metadata as part of stream updates for
non-modesets as long as we force a modeset when entering or exiting HDR.
This avoids unnecessary blanking for simple metadata updates.
[How]
When changing scaling and abm for the stream also check if HDR has
changed and send the stream update. This will only happen in non-modeset
cases.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-3-nicholas.kazlauskas@amd.com
[Why]
For userspace to send static HDR metadata to the display we need to
attach the property on the connector and send it to DC.
[How]
The property is attached to HDMI and DP connectors. Since the metadata
isn't actually available when creating the connector this isn't a
property we can dynamically support based on the extension block
being available or not.
When the HDR metadata is changed a modeset will be forced for now.
We need to switch from 8bpc to 10bpc in most cases anyway, and we want
to fully exit HDR mode when userspace gives us a NULL metadata, so this
isn't completely unnecessary.
The requirement can later be reduced to just entering and exiting HDR
or switching max bpc.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-2-nicholas.kazlauskas@amd.com
add ticket for display bo, so that it can preempt busy bo.
v2: fix stupid rebase error
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Issue:
Will have follow error when reload driver:
[ 3986.567739] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:07.0/drm_dp_aux_dev'
[ 3986.567743] CPU: 6 PID: 1767 Comm: modprobe Tainted: G OE 5.0.0-rc1-custom #1
[ 3986.567745] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 3986.567746] Call Trace:
......
[ 3986.567808] drm_dp_aux_register_devnode+0xdc/0x140 [drm_kms_helper]
......
[ 3986.569081] kobject_add_internal failed for drm_dp_aux_dev with -EEXIST, don't try to register things with the same name in the same directory.
Reproduce sequences:
1.modprobe amdgpu
2.modprobe -r amdgpu
3.modprobe amdgpu
Root cause:
When unload driver, it doesn't unregister aux.
v2: Don't use has_aux
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For commits with allow_modeset=false and CRTC degamma changes the planes
aren't reset. This results in incorrect rendering.
[How]
Reset the planes when color management has changed on the CRTC.
Technically this will include regamma changes as well, but it doesn't
really after legacy userspace since those commit with
allow_modeset=true.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.
[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc_destroy should be called amdgpu_cgs_destroy_device,
as it will use cgs context to read or write registers.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are monitors which can have more than one preferred mode
set. There are chances in these monitors that if common modes are
added in function amdgpu_dm_connector_add_common_modes(), these
common modes can be calculated with different preferred mode than
the one used in function decide_crtc_timing_for_drm_display_mode().
The preferred mode can be different because after common modes
are added, the mode list is sorted and this changes the order of
preferred modes in the list. The first mode in the list with
preferred flag set is selected as preferred mode. Due to this the
preferred mode selected varies.
If same preferred mode is not selected in common mode calculation
and crtc timing, then during mode set instead of setting preferred
timing, common mode timing will be applied which can cause "out of
range" message in the monitor with monitor blanking out.
[How]
Sort the modes before adding common modes. The same sorting function
is called during common mode addition and deciding crtc timing.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The current state on the connector is queried when getting the max bpc
rather than the new state. This means that a new max bpc value can only
currently take effect on the commit *after* it changes.
The new state should be passed in instead.
[How]
Pass down the dm_state as drm state to where we do color depth lookup.
The passed in state can still be NULL when called from
amdgpu_dm_connector_mode_valid, so make sure that we have reasonable
defaults in place. That should probably be addressed at some point.
This change now (correctly) causes a modeset to occur when changing the
max bpc for a connector.
v2: Drop extra TODO.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The custom "max bpc" property was added to limit color depth while the
DRM one was still being merged. It's been a few kernel versions since
then and this TODO was still sticking around.
[How]
Attach the DRM max bpc property to the connector and drop all of our
custom property management. Set the max bpc to 8 by default since
DRM defaults to the max in the range which would be 16 in this case.
No behavioral changes are intended with this patch, it should just be
a refactor.
v2: Don't force 8bpc when no state is given
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some early Raven boards had a bad SBIOS that doesn't play nicely with
the DMCU FW. We thought the issues were fixed by ignoring errors on DMCU
load but that doesn't seem to be the case. We've still seen reports of
users unable to boot their systems at all.
[HOW]
Disable DMCU load on Raven 1. Only load it for Raven 2 and Picasso.
v2: Fix ifdef (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In fill_plane_buffer_attributes() we calculate chroma/luma
assuming that the surface_pixel_format is always valid.
If it's not the case, there's a risk of divide by zero error.
[How]
Check if format valid before calculating pixel format attributes
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When x or y is negative we set the x and y values to 0 and compensate
with a positive cursor hotspot in DM since DC expects positive cursor
values.
When x or y is less than or equal to the maximum cursor width or height
the cursor hotspot is clamped so the hotspot doesn't exceed the
cursor size:
if (x < 0) {
xorigin = min(-x, amdgpu_crtc->max_cursor_width - 1);
x = 0;
}
if (y < 0) {
yorigin = min(-y, amdgpu_crtc->max_cursor_height - 1);
y = 0;
}
This incorrectly forces the cursor to be at least 1 pixel on the screen
in either direction when x or y is sufficiently negative.
[How]
Just disable the cursor when it goes far enough off the screen in one
of these directions.
This fixes kms_cursor_crc@cursor-256x256-offscreen.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some early Raven boards had a bad SBIOS that doesn't play nicely with
the DMCU FW. We thought the issues were fixed by ignoring errors on DMCU
load but that doesn't seem to be the case. We've still seen reports of
users unable to boot their systems at all.
[HOW]
Disable DMCU load on Raven 1. Only load it for Raven 2 and Picasso.
v2: Fix ifdef (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This reverts commit 55143dc23c.
This causes build breakags with some Kconfigs so revert for now.
Fixes: 55143dc23c ("drm/amd/display: Don't load DMCU for Raven 1")
Signed-off-by: Dave Airlie <airlied@redhat.com>
[WHY]
Some early Raven boards had a bad SBIOS that doesn't play nicely with
the DMCU FW. We thought the issues were fixed by ignoring errors on DMCU
load but that doesn't seem to be the case. We've still seen reports of
users unable to boot their systems at all.
[HOW]
Disable DMCU load on Raven 1. Only load it for Raven 2 and Picasso.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
The type of 'r' is uint32_t and the return codes for both:
- reservation_object_wait_timeout_rcu
- amdgpu_bo_reserve
...are signed. While it works for the latter since the check is
done on != 0 it doesn't work for the former since we check <= 0.
[How]
Make 'r' a long in commit planes so we're not doing any unsigned/signed
conversion here in the first place.
v2: use long instead of int (Christian)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pre-DCE12 needs special treatment for BTR / low framerate
compensation for more stable behaviour:
According to comments in the code and some testing on DCE-8
and DCE-11, DCE-11 and earlier only apply VTOTAL_MIN/MAX
programming with a lag of one frame, so the special BTR hw
programming for intermediate fixed duration frames must be
done inside the current frame at flip submission in atomic
commit tail, ie. one vblank earlier, and the fixed refresh
intermediate frame mode must be also terminated one vblank
earlier on pre-DCE12 display engines.
To achieve proper termination on < DCE-12 shift the point
when the switch-back from fixed vblank duration to variable
vblank duration happens from the start of VBLANK (vblank irq,
as done on DCE-12+) to back-porch or end of VBLANK (handled
by vupdate irq handler). We must leave the switch-back code
inside VBLANK irq for DCE12+, as before.
Doing this, we get much better behaviour of BTR for up-sweeps,
ie. going from short to long frame durations (~high to low fps)
and for constant framerate flips, as tested on DCE-8 and
DCE-11. Behaviour is still not quite as good as on DCN-1
though.
On down-sweeps, going from long to short frame durations
(low fps to high fps) < DCE-12 is a little bit improved,
although by far not as much as for up-sweeps and constant
fps.
v2: Fix some wrong locking, as pointed out by Nicholas.
v3: Simplify if-condition in vupdate-irq - nit by Nicholas.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RGB565 support isn't restricted to just the primary plane in DC, so
also expose support for it on overlays.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Originally we did the amdgpu_dm_handle_vrr_transition call before
interrupts were enabled. After the interrupt toggling logic was
moved around for support enabling CRTCs with no primary planes
active this was no longer being called in the case where there
wasn't a modeset.
This fixes failures in igt@kms_vrr@* with error
"Timed out: Waiting for vblank event".
[How]
Shift them back into the loop that always ran before interrupts were
enabled.
Pull out the logic that updated VRR state into the same loop since
there's no reason these need to be split.
In the case where we're going from VRR off, no planes to VRR on, some
active planes we'll still be covered for having the VRR vupdate
handler enabled - vblank will be re-enabled at this point, it will
see that VRR is active and set the vupdate interrupt on there.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the generic introduction of seamless boot, the display is no
longer blanked upon boot. However, this causes corruption on some
systems that does not lock the memory in the non-secure boot case,
resulting in brief corruption on boot due to garbage being written into
the frame buffer.
[How]
Add a flag, read during DC init, to determine whether display should be
blanked on boot. Default to true.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many userspace applications (and IGT) seem to expect that most drivers
can keep a CRTC active and enabled if there are no primary or overlay
planes.
DC is setup to handle this but only in the case where there are
absolutely no planes on the CRTC - no primary, cursor, or overlay.
[How]
Add a check to reject commits that have cursor planes enabled and
nothing else on CRTCs since we can't handle that. The new helper
does_crtc_have_active_cursor is used for this.
In atomic commit tail, we need to let DC know that there are zero
planes enabled when doing stream updates to let it disable and blank
pipes as appropriate.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When disabling all the pipes for a CRTC the page-flip interrupt also
gets disabled on Raven. We can't re-enable the page-flip interrupt
unless we give DC at least one active DC plane.
We currently enable interrupts after the call to dc_commit_state since
there's currently no valid sequence that should disable all the planes
or re-enable planes for a CRTC without first going through
dc_commit_state.
If we were to allow for a CRTC to be enabled with no primary plane this
would not be the case - the call to dc_commit_updates_for_stream would
enable the planes when going from zero to at least one active plane,
but manage_dm_interrupts would have been called too early.
This results in a page-flip timeout on any subsequent commits since we
think the page-flip are now enabled when they're actually disabled.
We need to enable interrupts after the call to
dc_commit_updates_for_stream.
[How]
Split enabling interrupts into two passes. One pass before
dc_commit_updates_for_stream and one after it.
Shifting all the interrupts to be strictly below the call doesn't
currently work even though it should in theory. We end up queuing
off the vblank event to be handle by the flip handler before it's
actually enabled in some cases, particularly:
old_crtc_state->active = false -> new_crtc_state->active = true
The framebuffer states haven't changed and we can technically still
do a "pageflip" in this case and send back the event.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We only currently drop the vblank reference when the stream is
being removed from the context. We should be dropping it whenever we
disable interrupts and reaquiring it after we re-enable them.
We also never get the extra reference correctly when re-enabling
interrupts, since grabbing the reference has the following condition:
if (!crtc_state->crc_enabled && enable)
drm_crtc_vblank_get(crtc);
This means that crc_enabled must be *false* in order to grab the extra
reference.
[How]
Always drop the ref whenever we're disabling interrupts.
Only disable CRC capture when the stream is being removed.
Always grab the ref by setting dm_new_crtc_state->crc_enabled = false
before the call to re-enable CRC capture.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can't do cursor programming after the planes have been disabled
since there won't be any pipes - leading to lock warnings and the wrong
cursor state being left in the registers.
When we re-enable the planes after the previous cursor state will also
remain if we don't have a cursor plane.
[How]
If we're disabling the planes then do the cursor programming first.
If we're not disabling the planes then do the cursor programming after.
Introduce the amdgpu_dm_commit_cursors helper to avoid code duplication
for both of these cases.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The vblank and pageflip interrupts should only be enabled for a CRTC
that's enabled and has active planes.
The current logic takes care of this, but isn't setup to handle the case
where the active plane count goes to zero but the stream remains
enabled.
We currently block this case since we don't allow commits that enable a
CRTC with no active planes, but shouldn't be any reason we can't support
this from a hardware perspective and many userspace applications expect
to be able to do it (like IGT).
[How]
The count_crtc_active_planes function fills in the number of
"active_planes" on the dm_crtc_state. This should be the same as
DC's plane_count on the stream_status but easier to access since we
don't need to lock the private atomic state with the DC context.
Add the "interrupts_enabled" flag to the dm_crtc_state and set it based
on whether the stream exists and if there are active planes on the
stream.
Update the disable and enable logic to make use of this new flag.
There shouldn't be any functional change (yet) with this patch.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add the amdgpu specific bits for timeline support
- Add internal interfaces for xgmi pstate support
- DC Z ordering fixes for planes
- Add support for NV12 planes in DC
- Add colorspace properties for planes in DC
- eDP optimizations if the GOP driver already initialized eDP
- DC bandwidth validation tracing support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419150034.3473-1-alexander.deucher@amd.com
Patch '5edb0c9b Fix deadlock with display during hanged ring recovery'
was accidentaly removed during one of DALs code merges.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't block others while waiting for the fences to finish, concurrent
submission is perfectly valid in this case and holding the lock can
prevent killed applications from terminating.
Signed-off-by: Christian König <ckoenig.leichtzumerken@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC and DM already support DRM_FORMAT_RGB565, it's just missing from the
list of valid formats.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a fast_validate parameter in dc_validate_global_state for future use
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
As long as we have at least one non-cursor plane enabled on a CRTC then
the CRTC itself can remain enabled.
This will allow for commits where there's an overlay plane enabled but
no primary plane enabled.
[How]
Remove existing primary plane fb != NULL checks and replace them with
the new does_crtc_have_active_plane helper.
This will be called from atomic check when validating the CRTC.
Since the primary plane state can now potentially be NULL we'll need
to guard for that when accessing it in some of the cursor logic.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Surface scaling info updates can affect bandwidth and blocks. We need
to be checking these with global validation to avoid underflow or
corruption.
[How]
Drop the state->allow_modeset early exit in
dm_determine_update_type_for_commit. Most of those should be considered
fast now anyway.
Fill in scaling info and it to the surface update in atomic
check.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM thinks that the update type should be full whenever a stream or
plane is added or removed (including recreations).
This won't match in the case where DC thinks what looks like a fast
update to DM is actually a medium or full - like scaling changes that
affect bandwidth and clocks.
[How]
Drop this warning. DC knows better than the DM does for determining
cases like this.
The other warning can be kept for now since it would warn on a pretty
serious DC or DM bug.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC expects the surface memory address to identify the surface.
This doesn't work with what we're doing with the temporary surfaces,
it will always assume this is a full update because the surface
isn't in the current context.
[How]
Use the surface directly. This doesn't give us much improvement yet,
since we always create a new dc_plane_state when state->allow_modeset
is true.
The call into dc_check_update_surfaces_for_stream also needs to be
locked, for two reasons:
1. It checks the current DC state
2. It modifies the surface update flags
Both of which could be currently in the middle of commit work from
commit tail.
A TODO here is to pass the context explicitly into this function and
find a way to get the surface update flags out of it without modifying
the surface in place.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Planes have downscaling limits and upscaling limits per format and DM
is expected to validate these using DC caps. We should fail atomic
check validation if we aren't capable of doing the scaling.
[How]
We don't currently create store which DC plane maps to which DRM plane
so we can't easily check the caps directly. For now add basic
constraints that cover the absolute min and max downscale / upscale
limits for most RGB and YUV formats across ASICs.
Leave a TODO indicating that these should really be done with DC caps.
We'll probably need to subclass DRM planes again in order to correctly
identify which DC plane maps to it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We currently don't do DC validation for medium or full updates where
the plane state isn't created. There are some medium and full updates
that can cause bandwidth or clock changes to occur resulting in
underflow or corruption.
We need to be able to fill surface and plane info updates during
atomic commit for dm_determine_update_type for commit. Since we already
do this during atomic commit tail it would be good if we had the same
logic in both places for creating these structures.
[How]
Introduce fill_dc_scaling_info and fill_dc_plane_info_and_addr.
These two functions cover the following three update structures:
- struct dc_scaling_info
- struct dc_plane_info
- struct dc_plane_address
Cleanup and adapter the existing fill_plane_* helpers to work with
these functions.
Update call sites that used most of these sub helpers directly to work
with the new functions. The exception being prepare_fb - we just want
the new buffer attributes specifically in the case where we're
creating the plane. This is needed for dc_commit_state in the case
where the FB hasn't been previously been used.
This isn't quite a refactor, but functionally driver behavior should
be mostly the smae as before. The one exception is that we now check
the return code for fill_plane_buffer_attributes which means that
commits will be rejected that try to enable DCC with erroneous
parameters.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pitch was only calculated based on format whenever the plane state
was recreated. This could result in surface corruption due to the
incorrect pitch being programmed when the surface pitch changed during
commits where state->allow_modeset = false.
[How]
Recalculate pitch at the same time we update the buffer address and
other buffer attributes. This function was previously called
fill_plane_tiling_attributes but I've also renamed it to
fill_plane_buffer_attributes to clarify the actual intent of the
function now that it's handling most buffer related attributes.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The overlay will be incorrectly placed *below* the primary plane for
commits with state->allow_modeset = true because the primary plane
won't be removed and recreated in the same commit.
[How]
Add the should_reset_plane helper to determine if the plane should be
reset or not. If we need to add or force reset any plane in the context
then we'll need to do the same for every plane on the stream.
Unfortunately we need to do the remove / recreate routine for removing
planes as well since DC currently isn't well equipped to handle the
plane with the top pipe being removed with other planes still active.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Plane scaling parameters are not correctly filled or updated when
performing fast updates.
They're filled when creating the dc plane state and during atomic check.
While the atomic check code path happens for the plane even during fast
updates, the issue is that they're done in place on the dc_plane_state
directly. This dc_plane_state may be the current state plane state
being used by the hardware, so these parameters won't be correctly
programmed.
The new scaling parameters should instead be passed as an update
to the plane.
[How]
Update fill_rects_from_plane_state to not modify dc_plane_state
directly. Update the call sites that use this to fill in the appropriate
values.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
there are some scaling capabilities such as fp16 which are known to be unsupported
on a given ASIC. exposing these static capabilities allows much simpler implementation
for OS interfaces which require to report such static capabilities to reduce the
number of dynamic validation calls
[how]
refactor the existing plane caps to be more extensible, and add fp16 and scaling
capabilities
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need DC's color space to match the color encoding and color space
specified by userspace to correctly render YUV surfaces.
[How]
Add the DRM color properties when the DC plane supports NV12.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardware can support video surfaces and DC tells us which planes are
suitable via DC plane caps.
[How]
The supported formats array will now vary based on what DC tells us,
so create an array and fill it dynamically based on plane types and
caps.
Ideally we'd query support for every format via DC plane caps, but for
the framework is in place to do so later with this.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When deciding to add properties or expose formats on DRM planes we
should be querying the caps for the DC plane it's supposed to represent.
[How]
Pass plane caps down into plane initialization, refactoring overlay
plane initialization to have the overlay plane be represented by
the first overlay capable DC plane.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When entering S3, amdgpu first calls DRM to cache the current atomic
state, then commit the 'all-disabled' state. This sets dc->current_state
to point at the private atomic object's dm_atomic_state->context, as
any regular atomic commit would.
Afterwards, amdgpu_dm calls dc_set_power_state() with S3 power state.
This invalidates dc->current_state by wiping it to 0, consequently
wiping dm_atomic_state->context.
During resume, the cached atomic state is restored. When getting the
private object however, the dm_atomic_state - containing the wiped
context - is duplicated into the atomic state. This causes DC validation
to fail during atomic check, as necessary function pointers in dc_state
are now NULL.
[How]
Recreate the private object's dm_atomic_state->context during resume,
restoring any static values such as function pointers.
A TODO item is added to move static read-only values out of dc_state -
they shouldn't be there anyways.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need DC's color space to match the color encoding and color space
specified by userspace to correctly render YUV surfaces.
[How]
Convert the DRM color encoding and color range properties to the
appropriate DC colorspace option and update the color space when
performing surface updates.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC provides a few visual confirmation debug options that can be
dynamically changed at runtime to help debug surface programming issues
but we don't have any way to access it from userspace.
[How]
Add the amdgpu_dm_visual_confirm debugfs entry.
It accepts a string containing the DC visual confirm enum value using
the debugfs attribute helpers.
The debugfs_create_file_unsafe can be used instead of
debugfs_create_file as per the documentation.
v2: Use debugfs helpers for getting and setting the value (Christian)
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The brace initialization used here generates warnings on some
compilers. For example, on GCC 4.9:
[...] In function ‘dm_determine_update_type_for_commit’:
[...] error: missing braces around initializer [-Werror=missing-braces]
struct dc_stream_update stream_update = { 0 };
^
Use memset to make this more portable.
v2: Specify the compiler / diagnostic in the commit message (Paul)
Cc: Sun peng Li <Sunpeng.Li@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
the member sdr_white_level of struct dc_cursor_attributes was not
initialized, then the random value result that
dcn10_set_cursor_sdr_white_level() set error hw_scale value 0x20D9(normal
value is 0x3c00), this cause the black cursor issue.
[how]
just initilize the obj of struct dc_cursor_attributes to zero to avoid
the random value.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Tianci Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Multiple threads were writing back to one global VBA in DC resulting
in multiple threads overwriting eachother's data
[How]
Add an instance of DML (which contains VBA) to each context and
change all calls that used dc->dml to use context->dml. Created a
seperate copy constructor for linux in a case where there is no
access to DC.
Signed-off-by: Aidan Wood <Aidan.Wood@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want vblank counts and timestamps of flip completion as sent
in pageflip completion events to be consistent with the vblank
count and timestamp of the vblank of flip completion, like in non
VRR mode.
In VRR mode, drm_update_vblank_count() - and thereby vblank
count and timestamp updates - must be delayed until after the
end of front-porch of each vblank, as it is only safe to
calculate vblank timestamps outside of the front-porch, when
we actually know when the vblank will end or has ended.
The function drm_update_vblank_count() which updates timestamps
and counts gets called by drm_crtc_accurate_vblank_count() or by
drm_crtc_handle_vblank().
Therefore we must make sure that pageflip events for a completed
flip are only sent out after drm_crtc_accurate_vblank_count() or
drm_crtc_handle_vblank() is executed, after end of front-porch
for the vblank of flip completion.
Two cases:
a) Pageflip irq handler executes inside front-porch:
In this case we must defer sending pageflip events until
drm_crtc_handle_vblank() executes after end of front-porch,
and thereby calculates proper vblank count and timestamp.
Iow. the pflip irq handler must just arm a pageflip event
to be sent out by drm_crtc_handle_vblank() later on.
b) Pageflip irq handler executes after end of front-porch, e.g.,
after flip completion in back-porch or due to a massively
delayed handler invocation into the active scanout of the new
frame. In this case we can call drm_crtc_accurate_vblank_count()
to safely force calculation of a proper vblank count and
timestamp, and must send the pageflip completion event
ourselves from the pageflip irq handler.
This is the same behaviour as needed for standard fixed refresh
rate mode.
To decide from within pageflip handler if we are in case a) or b),
we check the current scanout position against the boundary of
front-porch. In non-VRR mode we just do what we did in the past.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In VRR mode, proper vblank/pageflip timestamps can only be computed
after the display scanout position has left front-porch. Therefore
delay calls to drm_crtc_handle_vblank(), and thereby calls to
drm_update_vblank_count() and pageflip event delivery, to after the
end of front-porch when in VRR mode.
We add a new vupdate irq, which triggers at the end of the vupdate
interval, ie. at the end of vblank, and calls the core vblank handler
function. The new irq handler is not executed in standard non-VRR
mode, so vblank handling for fixed refresh rate mode is identical
to the past implementation.
v2: Implement feedback by Nicholas and Paul Menzel.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For throttling to work correctly, we always need a baseline vblank
count last_flip_vblank that increments at start of front-porch.
This is the case for drm_crtc_vblank_count() in non-VRR mode, where
the vblank irq fires at start of front-porch and triggers DRM core
vblank handling, but it is no longer the case in VRR mode, where
core vblank handling is done later, after end of front-porch.
Therefore drm_crtc_vblank_count() is no longer useful for this.
We also can't use drm_crtc_accurate_vblank_count(), as that would
screw up vblank timestamps in VRR mode when called in front-porch.
To solve this, use the cooked hardware vblank counter returned by
amdgpu_get_vblank_counter_kms() instead, as that one is cooked to
always increment at start of front-porch, independent of when
vblank related irq's fire.
This patch allows vblank irq handling to happen anywhere within
vblank of even after it, without a negative impact on flip
throttling, so followup patches can shift the vblank core
handling trigger point wherever they need it.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During VRR mode we can not allow vblank irq dis-/enable
transitions, as an enable after a disable can happen at
an arbitrary time during the video refresh cycle, e.g.,
with a high likelyhood inside vblank front-porch. An
enable during front-porch would cause vblank timestamp
updates/calculations which are completely bogus, given
the code can't know when the vblank will end as long
as we are in front-porch with no page flip completed.
Hold a permanent vblank reference on the crtc while
in active VRR mode to prevent a vblank disable, and
drop the reference again when switching back to fixed
refresh rate non-VRR mode.
v2: Make sure transition is also handled if vrr is
disabled and stream gets disabled in the same
atomic commit by moving the call to the transition
function outside of plane commit.
Suggested by Nicholas.
v3: Trivial rebase onto previous patch.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need the VRR active/inactive state info earlier in
the commit sequence, so VRR related setup functions like
amdgpu_dm_handle_vrr_transition() know the final VRR state
when they need to do their hw setup work.
Split update_freesync_state_on_stream() into an early part,
that can run at the beginning of commit tail before the
vrr transition handling, and a late part that must run after
vrr transition handling inside the commit planes code for
enabled crtc's.
Suggested by Nicholas Kazlauskas.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu:
- Switch to HMM for userptr (reverted until HMM fixes land)
- New experimental SMU 11 replacement for powerplay for vega20 (not enabled by default)
- Initial RAS support for vega20
- BACO support for vega12
- BACO fixes for vega20
- Rework IH handling for page fault and retry interrupts
- Cleanly split CPU and GPU paths for GPUVM updates
- Powerplay fixes
- XGMI fixes
- Rework how DC interacts with atomic for planes
- Clean up and simplify DC/Powerplay interfaces
- Misc cleanups and bug fixes
amdkfd:
- Switch to HMM for userptr (reverted until HMM fixes land)
- Add initial RAS support
- MQD fixes
ttm:
- Unify DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
- Misc cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190402170820.22197-1-alexander.deucher@amd.com
[Why]
set_display_requirement, dcn1_pplib_apply_display_requirements
are no longer used and should be removed.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
program default output gamma if no user specific gamma
parameters passed.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Black screens or artifacting can occur when enabling FreeSync outside
of the supported range of the monitor. This can happen since the
supported range isn't always the min/max vrefresh range available for
the monitor.
[How]
There was previously a fix that prevented this from happening in the
low range but it didn't cover the upper range. Expand the condition
to include both.
Cc: Sun peng Li <Sunpeng.Li@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want DRM planes to be initialized in the following order:
- primary planes
- overlay planes
- cursor planes
to support existing userspace expectations for plane z-ordering. This
means that we also need to register CRTCs after all planes have been
initialized since overlay planes can be placed on any CRTC.
So the only reason why we have the mode_info->planes list is to
remember the primary planes for use later when we need to register
the CRTC.
Overlay planes have no purpose being in this list. DRM will cleanup
any planes that we've registered for us, so the only planes that need to
be explicitly cleaned up are the ones that have failed to register.
By dropping the explicit free on every plane in the mode_info->planes
list this patch also fixes a double-free in the case where we fail to
initialize only some of the planes.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need arbitrary read/write over DP AUX DPCD
for debugging
[How]
Three debugfs entries
Set the target address by writing to
"aux_dpcd_address"
(The first four bytes written are used)
Set the transaction size in bytes by writing to
"aux_dpcd_size"
(The first four bytes written are used)
Start a transaction by reading/writing
"aux_dpcd_data"
Do note: there is no concerrency protection at all
Accessing these entries in quick succession can lead
to strange behaviour
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to add DP SDP message test debugfs to make sdp message test
more convenient and efficient.
[How]
Add sdp_message debugfs entry in amdgpu.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Somewhere in the atomic check reshuffle ABM got lost.
ABM is a crtc property (copied from a connector property).
It can change without a modeset, just like underscan.
[How]
In the skip_modeset branch of atomic check crtc updates,
copy over the abm property.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To help prevent plane state not being set to the correct default
value if any new properties are added in the future.
[How]
Use the drm helper - which seems to be the common solution among other
DRM drivers.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The plane_reset callback is subclassed but hasn't been updated since
the drm helper got updated to include resetting alpha related state
(state->alpha and state->pixel_blend_mode). The overlay planes
exposed by amdgpu_dm were therefore being rendered as invisible by
default ever since supported was exposed for alpha blending properties
on overlays.
This caused regressions in igt@kms_plane_multiple@atomic-tiling-none
and igt@kms_plane@plane-position-covered-pipe tests.
[How]
Reset the plane state values to their correct values as defined in
the drm helper.
This fixes the IGT test regression.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect hardcoded assumptions are made regarding luma and chroma
alignment. The actual values set for the DRM framebuffer should be used
when programming the address.
[How]
Respect the given pitch for both luma and chroma planes - it's not like
we can force the alignment to anything else at this point anyway.
Use the FB offset for the chroma planes directly. DRM already
provides this to us so there's no need to calculate it manually.
While we don't actually use the chroma surface size parameters on Raven,
these should have technically been fb->width / 2 and fb->height / 2
since the chroma plane is half size of the luma plane for NV12.
Leave a TODO indicating that those should be set based on the actual
surface format instead since this is only correct for YUV420 formats.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For new DC planes the correct plane address fields are filled based
on whether the plane had a graphics or video format.
However, when we perform stream and plane updates using DC we only ever
fill in the graphics format fields. This causing corruption and hangs
when using video surface formats like NV12 for planes.
[How]
Use the same logic everywhere we update dc_plane_address - always
fill in the correct fields based on the surface format type.
There are 3 places this is done:
- Atomic check, during DC plane creation
- Atomic commit, during plane prepare_fb
- Atomic commit tail, during amdgpu_dm_commit_planes
We use the fill_plane_tiling_attributes in all 3 locations and it
already needs the address to update DCC attributes, so the surface
address update logic can be moved into this helper.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DRM overlay planes DM exposes support RGBA formats but are currently
forced as fully opaque over whatever they overlay.
[How]
Expose DRM blending mode and alpha properties to userspace.
The overlays exposed support per-pixel pre-multiplied alpha along with
global plane opacity.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Can happen on ASICs with 6 planes, but this isn't a bug since we haven't
written outside the array.
[How]
Use <= instead of <.
Cc: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reported-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
New DRM versions manage locking for private objects for us, so this
is no longer needed.
This also prevents a WARN_ON from occurring when the private object is
duplicated during the forced atomic commit that occurs from the HPD
handler.
The HPD handler calls drm_modeset_lock_all before the forced commit
and if the private object is duplicated then the
DEBUG_LOCKS_WARN_ON(ww_ctx->done_acquire) warning will be triggered
since we're trying to lock something when everything should have
already been locked.
[How]
Drop the lock and let DRM manage this.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Tiling and DCC attributes can change when swapping framebuffers but
these will only ever get updated on full commits where
state->allow_modeset is true. But for the page-flip IOCTL
state->allow_modeset = false so these aren't updated and DCC changes
aren't being programmed.
[How]
Split out updating the tiling and DCC attributes into its own function
that's called when creating the plane for the first time but also
called when switching framebuffers before commit stream updates.
These functions also don't modify the plane state directly since the
plane state being used as reference is often the current one
being used by the hardware.
DC needs to be able to compare plane_state to the stream update
structures to determine if the hardware programming should happen. If
it's modified in place then nothing will be programmed and we can run
into concurrency issues.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
commit_planes is indented quite far
[How]
Move the pageflip code from an if statement to after a
continue
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IGT expects that pageflips can be triggered with the same
framebuffer before and after the commit
[How]
Expand the definition of pageflip to include any change
with an old framebuffer and a new framebuffer, even if they're
the same
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Raven has support for combining pipes for DRM_PLANE_TYPE_OVERLAY use
but no overlays are exposed to userspace.
[How]
Expose overlay planes based on DC plane caps.
If all the pipes are in use then the atomic commits can fail, but this
is expected behavior for userspace.
Only support RGB on overlays for now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Primary and underlay planes were previously exposed to DRM by using
max_planes and max_slave_planes.
The value for max_planes was always pipe_count + has_underlay.
If there was an underlay pipe, then max_slave_planes = 1.
Raven has pipe_count = 4, max_planes = 4, and max_slave_planes = 1.
So during plane initialziation it was actually "creating"
1 overlay plane and 3 primary planes... or it would be, had its
plane_type array not been dm_plane_type_default, which will only create
DRM_PLANE_TYPE_PRIMARY planes.
We can expose primary planes as supporting more than one CRTC at a time
to more closely resemble plane behavior on DCN but userspace doesn't
really expect planes to be used in this manner and will either
ignore the planes or crash.
Planes with index greater than max_streams are marked as supporting
all CRTCs. No ASIC currently has primary plane count greater than the
stream count but we shouldn't expose more than necessary.
[How]
Drop support for underlay planes. They aren't well tested and don't
fully work right at the moment.
Only create one primary plane per CRTC so we're not creating overlays.
Initialize plane types directly instead of referencing a misleading
array of plane types.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The kms_plane@plane-position-covered-pipe-*-planes subtests can produce
a sequence of atomic commits such that neither active_changed nor
mode_changed but connectors_changed.
When this happens we remove the old stream from the context and add
a new stream but the new stream doesn't have mode_changed=true set.
This incorrect programming sequence causes CRC mismatches to occur in
the test.
The stream->mode_changed value should be set whenever a new stream
is created.
[How]
A new stream is created whenever drm_atomic_crtc_needs_modeset is true.
We previously covered the active_changed and mode_changed conditions
for the CRTC but connectors_changed is also checked within
drm_atomic_crtc_needs_modeset.
So just use drm_atomic_crtc_needs_modeset directly to determine the
mode_changed flag.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new aux implementation was not up to spec. This caused us to fail DP
compliance as well as introduced serious delays during system resume.
[How]
Make dce_aux_transfer_raw return the operation result
Make dce_aux_transfer_with_retries delay with udelay instead
of msleep, and only on invalid reply. Also fail on the second
invalid reply, third timeout, or first of any other error
Convert return values to drm error codes in amdgpu_dm
As the two aux transfer functions are now noticeably
different, change the names to better reflect their
functionality and document.
There was one last call to dc_link_aux_transfer that
should have retries, fix that
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With special monitor combination on MST, the UP_REQ could come
after clear payload table. It makes the pending DOWN_REP fail
to be handled after link training and the new DOWN_REQ will be queued
until time out .
[How]
To move the current polling pending DOWN_REP procedure to after
clear payload table to make sure the pending DOWN_REP can be
done before enabling the link.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch implements inteferface to set watermarks table for clock ranges on
smu 11. It fills watermark table before it is written to SMC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds interface to notify smu enable pme restore register for display
and in smu v11 didn't have this implementation.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fills the amd_pp_clock_info data for display, it will get the current
info in that structure.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds interface to request display clock voltage, display will use it
to request current display clock voltage.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds inteface to get clock by type with voltage, display will use it
to get current clocks with voltage.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds get clock by type with latency, display will use it to get
current clocks with latency.
v2: fix the missed mutex lock before return.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds interface to get max high clocks for display and in smu v11
didn't have this implementation.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds get_clock_by_type interface for display, in smu v11 didn't have
the implementation.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds display configuration change function that creates the new path
with sw smu driver instead of powerplay.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_commit_updates_for_stream is called twice per stream: once
with the flip data and once will all other data. This causes
problems when these DC calls have different numbers of planes
For example, a commit with a pageflip on plane A and a
non-pageflip change on plane B will first call
into DC with just plane A, causing plane B to be
disabled. Then it will call into DC with both planes,
re-enabling plane B
[How]
Merge flip and full into a single bundle
Apart from the single DC call, the logic should not be
changed by this patch
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The wait_for_vblank boolean in commit_tail was passed by reference
into each stream commit, and if that commit was an asynchronous
flip, it would disable vblank waits on all subsequent flips.
This made the behaviour depend on crtc order in a non-intuitive way,
although since the asynchronous pageflip flag is only used by the
legacy IOCTLs at the moment it is never an issue
[How]
Find wait_for_vblank before doing any stream commits
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make dml and integration with pplib clearer.
[How]
Change the way the dml formula is initialized to make its values more
clear. Restructure DC interface with pplib into rv_funcs.
Cap clocks received from pplib.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In VRR mode, keep track of the vblank count of the last
completed pageflip in amdgpu_crtc->last_flip_vblank, as
recorded in the pageflip completion handler after each
completed flip.
Use that count to prevent mmio programming a new pageflip
within the same vblank in which the last pageflip completed,
iow. to throttle pageflips to at most one flip per video
frame, while at the same time allowing to request a flip
not only before start of vblank, but also anywhere within
vblank.
The old logic did the same, and made sense for regular fixed
refresh rate flipping, but in vrr mode it prevents requesting
a flip anywhere inside the possibly huge vblank, thereby
reducing framerate in vrr mode instead of improving it, by
delaying a slightly delayed flip requests up to a maximum
vblank duration + 1 scanout duration. This would limit VRR
usefulness to only help applications with a very high GPU
demand, which can submit the flip request before start of
vblank, but then have to wait long for fences to complete.
With this method a flip can be both requested and - after
fences have completed - executed, ie. it doesn't matter if
the request (amdgpu_dm_do_flip()) gets delayed until deep
into the extended vblank due to cpu execution delays. This
also allows clients which want to regulate framerate within
the vrr range a much more fine-grained control of flip timing,
a feature that might be useful for video playback, and is
very useful for neuroscience/vision research applications.
In regular non-VRR mode, retain the old flip submission
behavior. This to keep flip scheduling for fullscreen X11/GLX
OpenGL clients intact, if they use the GLX_OML_sync_control
extensions glXSwapBufferMscOML(, ..., target_msc,...) function
with a specific target_msc target vblank count.
glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will
not flip at the proper target_msc for a non-zero target_msc
if VRR mode is active with this patch. They'd often flip one
frame too early. However, this limitation should not matter
much in VRR mode, as scheduling based on vblank counts is
pretty futile/unusable under variable refresh duration
anyway, so no real extra harm is done.
According to some testing already done with this patch by
Nicholas on top of my tests, IGT tests didn't report any
problems. If fixes stuttering and flickering when flipping
at rates below the minimum vrr refresh rate.
Fixes: bb47de7366 ("drm/amdgpu: Set FreeSync state using drm VRR
properties")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Tested-by: Bruno Filipe <bmilreu@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In VRR mode, keep track of the vblank count of the last
completed pageflip in amdgpu_crtc->last_flip_vblank, as
recorded in the pageflip completion handler after each
completed flip.
Use that count to prevent mmio programming a new pageflip
within the same vblank in which the last pageflip completed,
iow. to throttle pageflips to at most one flip per video
frame, while at the same time allowing to request a flip
not only before start of vblank, but also anywhere within
vblank.
The old logic did the same, and made sense for regular fixed
refresh rate flipping, but in vrr mode it prevents requesting
a flip anywhere inside the possibly huge vblank, thereby
reducing framerate in vrr mode instead of improving it, by
delaying a slightly delayed flip requests up to a maximum
vblank duration + 1 scanout duration. This would limit VRR
usefulness to only help applications with a very high GPU
demand, which can submit the flip request before start of
vblank, but then have to wait long for fences to complete.
With this method a flip can be both requested and - after
fences have completed - executed, ie. it doesn't matter if
the request (amdgpu_dm_do_flip()) gets delayed until deep
into the extended vblank due to cpu execution delays. This
also allows clients which want to regulate framerate within
the vrr range a much more fine-grained control of flip timing,
a feature that might be useful for video playback, and is
very useful for neuroscience/vision research applications.
In regular non-VRR mode, retain the old flip submission
behavior. This to keep flip scheduling for fullscreen X11/GLX
OpenGL clients intact, if they use the GLX_OML_sync_control
extensions glXSwapBufferMscOML(, ..., target_msc,...) function
with a specific target_msc target vblank count.
glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will
not flip at the proper target_msc for a non-zero target_msc
if VRR mode is active with this patch. They'd often flip one
frame too early. However, this limitation should not matter
much in VRR mode, as scheduling based on vblank counts is
pretty futile/unusable under variable refresh duration
anyway, so no real extra harm is done.
According to some testing already done with this patch by
Nicholas on top of my tests, IGT tests didn't report any
problems. If fixes stuttering and flickering when flipping
at rates below the minimum vrr refresh rate.
Fixes: bb47de7366 ("drm/amdgpu: Set FreeSync state using drm VRR
properties")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Tested-by: Bruno Filipe <bmilreu@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlx8YYIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGs5MIAIiVVIH+C0St60vf
nzfGpVe+BETe199UveM4Ic2FWMk97ZhSk5Oj6HwYY9vnw4iwoRCZIO5B8Dna4nxY
8XjiwxpJRVLq+7Y1d61O6NHo6UjFHF0GMzyeJeNNUq+mCISxZdLsqzsszt9X09mA
GoJjZ0UMw2Tkz/s3Ie4MumKASc+y2CjJc0ZVEZlJsMaqMJLIfUn/CrTzHBivmuqJ
sV6ZkP4as6h87bI9mi79p8pzvVooCRJ10cg4A/DHG4t2bEAIlB4t5dfZRFzVMhVo
cCPRk9tiA9y4I3zBjcuAZMODcBpfdWoQK8TqYw2cDS3LEDMgnEdIH6snMYHr69z0
kZJjA2A=
=Qs0l
-----END PGP SIGNATURE-----
Merge v5.0 into drm-next
There is a really hairy resolution involving amdgpu fixes, that I'd rather confirm here.
Also some misc fixes are landed by me, but the pr has them as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>
In VRR mode, keep track of the vblank count of the last
completed pageflip in amdgpu_crtc->last_flip_vblank, as
recorded in the pageflip completion handler after each
completed flip.
Use that count to prevent mmio programming a new pageflip
within the same vblank in which the last pageflip completed,
iow. to throttle pageflips to at most one flip per video
frame, while at the same time allowing to request a flip
not only before start of vblank, but also anywhere within
vblank.
The old logic did the same, and made sense for regular fixed
refresh rate flipping, but in vrr mode it prevents requesting
a flip anywhere inside the possibly huge vblank, thereby
reducing framerate in vrr mode instead of improving it, by
delaying a slightly delayed flip requests up to a maximum
vblank duration + 1 scanout duration. This would limit VRR
usefulness to only help applications with a very high GPU
demand, which can submit the flip request before start of
vblank, but then have to wait long for fences to complete.
With this method a flip can be both requested and - after
fences have completed - executed, ie. it doesn't matter if
the request (amdgpu_dm_do_flip()) gets delayed until deep
into the extended vblank due to cpu execution delays. This
also allows clients which want to regulate framerate within
the vrr range a much more fine-grained control of flip timing,
a feature that might be useful for video playback, and is
very useful for neuroscience/vision research applications.
In regular non-VRR mode, retain the old flip submission
behavior. This to keep flip scheduling for fullscreen X11/GLX
OpenGL clients intact, if they use the GLX_OML_sync_control
extensions glXSwapBufferMscOML(, ..., target_msc,...) function
with a specific target_msc target vblank count.
glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will
not flip at the proper target_msc for a non-zero target_msc
if VRR mode is active with this patch. They'd often flip one
frame too early. However, this limitation should not matter
much in VRR mode, as scheduling based on vblank counts is
pretty futile/unusable under variable refresh duration
anyway, so no real extra harm is done.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes for 5.1:
amdgpu:
- Fix missing fw declaration after dropping old CI DPM code
- Fix debugfs access to registers beyond the MMIO bar size
- Fix context priority handling
- Add missing license on some new files
- Various cleanups and bug fixes
radeon:
- Fix missing break in CS parser for evergreen
- Various cleanups and bug fixes
sched:
- Fix entities with 0 run queues
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221214134.3308-1-alexander.deucher@amd.com
[Why]
Cursor updates used to happen after vblank/flip/stream updates before
the stream update refactor. They now happen before stream updates
which means that they're not going to be synced with fb changes
and that they're going to programmed for pipes that we're disabling
within the same commit.
[How]
Move them after stream updates.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever a stream or plane is added or removed from the context the
pointer will change from old to new. We set lock and validation
needed in these cases. But not all of these cases match update_type
from dm_determine_update_type_for_commit - an example being overlay
plane updates.
There are warnings for a few of these cases that should be fixed.
[How]
We can closer align to DC (and lock_and_validation_needed) by
comparing stream and plane pointers.
Since the old stream/old plane state is never freed until sometime
after the commit tail work finishes we are guaranteed to never get
back the same block of memory when we remove and create a stream or
plane state in the same commit.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This format isn't supported in DC and some IGT tests fail since we
expose support for it.
[How]
Remove it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If a commit updates an overlay plane via the legacy plane IOCTL
then the only plane in the state will be the overlay plane.
Overlay planes need to be added first to the DC context, but in the
scenario above the plane will be added last. This will result in wrong
z-order during rendering.
[How]
If any non-cursor plane has been updated then the rest of the
non-cursor planes should be added to the CRTC state.
The cursor plane doesn't need to be included for stream updates and
locking it will cause performance issues. It should be ignored.
DC requires that the surface count passed during stream updates
be the number of surfaces currently on the stream to enable fast
updates. This previously wasn't the case without this patch, so this
also allows this optimization to occur.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm_dp_mst_topology_mgr_suspend() is added into the new reboot
sequence, which disables the UP request at the beginning.
Therefore sideband messages are blocked.
[How]
Finish MST sideband message transaction before UP request is
suppressed.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge v5.0-rc7 into drm-next
Backmerging for nouveau and imx that needed some fixes for next pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
When ring hang happens amdgpu_dm_commit_planes during flip is holding
the BO reserved and then stack waiting for fences to signal in
reservation_object_wait_timeout_rcu (which won't signal because there
was a hnag). Then when we try to shutdown display block during reset
recovery from drm_atomic_helper_suspend we also try to reserve the BO
from dm_plane_helper_cleanup_fb ending in deadlock.
Also remove useless WARN_ON
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's useful to know the min and max vrr range for IGT testing.
[How]
Expose the min and max vfreq for the connector via a debugfs file
on the connector, "vrr_range".
Example usage: cat /sys/kernel/debug/dri/0/DP-1/vrr_range
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The dc_sink was released but the pointer on the aconnector was
not cleared.
[How]
Clear it.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are opt1c lock warnings and CRTC read timeouts when running the
"igt@kms_plane@plane-position-hole-dpms-pipe-*" tests. These are
caused by trying to reprogram planes that are not in the current
context.
DPMS off removes the stream from the context. In this case:
new_crtc_state->active_changed = true
new_crtc_state->mode_changed = false
The planes are reprogrammed before the stream is removed from the
context because stream_state->mode_changed = false.
For DPMS adds the stream and planes back to the context:
new_crtc_state->active_changed = true
new_crtc_state->mode_changed = false
The planes are also reprogrammed here before the stream is added to the
context because stream_state->mode_changed = true. They were not
previously in the current context so warnings occur here.
[How]
Set stream_state->mode_changed = true when
new_crtc_state->active_changed = true too.
This prevents reprogramming before the context is applied in DC. The
programming will be done after the context is applied.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It fixes the failure to create stream for sink in the scenario
when hotplug SST and MST in sequence, and disconnect MST.
[How]
Add the fake sink back after the majority of MST rework is done.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Setting monitor refresh rate below freesync range would cause the
monitor to go blank indefinitely with freesync enabled
[How]
Set vrr_supported and ignore_msa_timing_param according to whether
the refresh rate is above or below the minimum freesync frequency.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This provides little debug value and creates a lot of dmesg noise.
[How]
Remove it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The stream_update struct is left unitialized but DC will access
its fields. This usually results in global state validation occur
during any atomic commit with state->allow_modeset = true.
[How]
Initialize the struct to zero for every stream we check.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The indenting for this function is a few levels too deep and can be
simplified a fair bit. This patch is in preparation for functional
changes that fix update type determination to occur less frequently
and more accurately.
[How]
Place checks early and exit/continue when possible. This isn't
a functional change.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We were always passing the first surface on the stream status for
flip updates when we should be using the surface associated with
the plane.
[How]
Use the dc_plane_state from the plane that's being updated.
FreeSync should also only keep track of updates from the primary
plane, so the check needed to be updated.
The acrtc->stream state doesn't need to be checked for NULL before
updating FreeSync either since there needs to be a stream to be
inside this function as a prerequisite.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Most surface updates weren't propagated onto the surface during
dc_commit_updates_for_stream. This makes it more difficult for DC to
determine the actual surface update type required.
[How]
Use copy_surface_update_to_plane to propagate the changes. The FreeSync
surface timing information update for BTR has been moved out of
amdgpu_dm.c into this function as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When CONFIG_DEBUG_FS isn't defined then amdgpu_dm_crtc_set_crc_source
is NULL. This causes a compilation error since it's being called
unconditionally.
[How]
Guard the call based on CONFIG_DEBUG_FS - CRC capture isn't supported
without this.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Fixes: 43a6a02eb3 ("drm/amd/display: Re-enable CRC capture following modeset")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:2314:38:
warning: suggest braces around initialization of subobject
[-Wmissing-braces]
struct dc_surface_dcc_cap output = {0};
^
{}
Previous efforts to fix this type of warning by adding or removing
braces have been met with some pushback in favor of using memset [1][2].
Do that here, mirroring commit 05794eff1a ("drm/amdgpu/gmc: fix
compiler errors [-Werror,-Wmissing-braces] (V2)") in this tree.
[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
Fixes: 7df7e505e8 ("drm/amd/display: Set requested plane state DCC params for GFX9")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:5089:60:
warning: suggest braces around initialization of subobject
[-Wmissing-braces]
struct dc_surface_update dummy_updates[MAX_SURFACES] = { 0 };
^
{}
Previous efforts to fix this type of warning by adding or removing
braces have been met with some pushback in favor of using memset [1][2].
Do that here, mirroring commit 05794eff1a ("drm/amdgpu/gmc: fix
compiler errors [-Werror,-Wmissing-braces] (V2)") in this tree.
[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
Fixes: 02d6a6fcdf ("drm/amd/display: Simplify underscan and ABM commit")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP was missing in the checks for supported VRR connectors.
[How]
Attach the properties for eDP connectors too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202449
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- Split out some part of drm_crtc_helper.h into drm_probe_helper.h
- DRIVER_* flags improvements
- New tasks on the TODO-list
- Improvements to the documentation
Driver Changes:
- Continual of drmP.h removal in multiple drivers
- Removal of FBINFO_(FLAG_)DEFAULT in multiple drivers
- sun4i: Addition of the A23 support, multiple fixes for the tiled
formats
- atmel-hlcdc: Fix of clipping and rotation properties
- qxl: various BO-related improvements, prime and generic fbdev emulation
support
- dw-hdmi: Support for HDMI2.0 2160p modes and YUV420 output
- New Sitronix ST7701 panel driver
- New Kingdisplay KD097D04 panel driver
- New LeMaker BL035-RGB-002 panel driver
- New PDA 91-00156-A0 panel driver
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXFRb/wAKCRDj7w1vZxhR
xXj2AQDFAkH0/tksJ+T6yrHZXQE7q/6fAWTlrDXLo7Nb1hhfswEA1AyaHmZJA0Ar
u7S+4Gfzs/gisw9Jr4bqQaerEpYJxQA=
=qumD
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-02-01' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- Split out some part of drm_crtc_helper.h into drm_probe_helper.h
- DRIVER_* flags improvements
- New tasks on the TODO-list
- Improvements to the documentation
Driver Changes:
- Continual of drmP.h removal in multiple drivers
- Removal of FBINFO_(FLAG_)DEFAULT in multiple drivers
- sun4i: Addition of the A23 support, multiple fixes for the tiled
formats
- atmel-hlcdc: Fix of clipping and rotation properties
- qxl: various BO-related improvements, prime and generic fbdev emulation
support
- dw-hdmi: Support for HDMI2.0 2160p modes and YUV420 output
- New Sitronix ST7701 panel driver
- New Kingdisplay KD097D04 panel driver
- New LeMaker BL035-RGB-002 panel driver
- New PDA 91-00156-A0 panel driver
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190201144749.t3abxvguhstu6bcl@flea
New stuff for 5.1.
amdgpu:
- DC bandwidth formula updates
- Support for DCC on scanout surfaces
- Support for multiple IH rings on soc15 asics
- Fix xgmi locking
- Add sysfs interface to get pcie usage stats
- Simplify DC i2c/aux code
- Initial support for BACO on vega10/20
- New runtime SMU feature debug interface
- Expand existing sysfs power interfaces to new clock domains
- Handle kexec properly
- Simplify IH programming
- Rework doorbell handling across asics
- Drop old CI DPM implementation
- DC page flipping fixes
- Misc SR-IOV fixes
amdkfd:
- Simplify the interfaces between amdkfd and amdgpu
ttm:
- Add a callback to notify the driver when the lru changes
sched:
- Refactor mirror list handling
- Rework hw fence processing
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125231517.26268-1-alexander.deucher@amd.com
[Why]
The flip and full structures were allocated but never freed.
[How]
Free them at the end of the function. There's a small behavioral
change here with the function returning early if the allocation fails
but we wouldn't should be doing anything in that case anyway.
Fixes: c00e0cc0fdc0 ("drm/amd/display: Call into DC once per multiplane flip")
Fixes: ea39594e0855 ("drm/amd/display: Perform plane updates only when needed")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During any modeset the CRTC stream is removed and a new stream is added.
This new stream doesn't carry over CRC capture state if it was
previously set.
[How]
Re-program the stream for CRC capture. The existing DRM callback can
be re-used here for the most part - the only modification needed is
additional locking now that it's called from within commit tail.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to read CRC events when CRC capture is enabled the vblank
interrput handler needs to be running for the CRTC. The handler is
enabled while there is an active vblank reference.
When running IGT tests there will often be no active vblank reference
but the test expects to read a CRC value. This is valid usage (and
works on i915 since they have a CRC interrupt handler) so the reference
to the vblank should be grabbed while capture is active.
This issue was found running:
igt@kms_plane_multiple@atomic-pipe-b-tiling-none
The pipe-b is the only one in the initial commit and was not previously
active so no vblank reference is grabbed. The vblank interrupt is
not enabled and the test times out.
[How]
Keep a reference to the vblank as long as CRC capture is enabled.
If userspace never explicitly disables it then the reference is
also dropped when removing the CRTC from the context (stream = NULL).
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On current design, driver cannot handle the interrupt for
down reply when link training is processing. The DOWN REQ
send before link training will keep in the pending DOWN REP
state in the queue.
It makes the next DOWN REQ be queued until time out.
[How]
To add a polling sequence before clear payload allocation table
to make sure the pending DOWN REP can be handled.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We were assuming that any commit with allow_modeset == false
was a pageflip. This was against drm intention and only
worked by sheer luck
[How]
A pageflip is the change from one framebuffer to another
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Our old logic: if pageflip, update freesync and plane address.
Otherwise, update everything.
This over-updated on non-pageflip cases, and it failed to
update if pageflip and non-pageflip changes occurred on
the same commit
[How]
Update flip_addrs on pageflips.
Update scaling_info when it changes.
Update color fields on color changes.
Updates plane_info always because we don't have a good way of
knowing when it needs to be updated.
Unfortunately, this means that every stream commit involves two
calls into DC. In particular, on pageflips there is a second,
pointless update that changes nothing but costs several
microseconds (about a 50% increase in time taken). The update is
fast, but there are comparisons and some useless programming.
Leave TODOs indicating dissatisfaction.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
amdgpu_dm_commit_planes was performing multi-plane
flips incorrectly:
It waited for vblank once per flipped plane
It prepared flip ISR and acquired the corresponding vblank ref
once per plane, although it closed ISR and put the ref once
per crtc
It called into dc once per flipped plane, duplicating some work
[How]
Wait for vblank, get vblank ref, prepare flip ISR, and call into
DC only once, and only if there is a pageflip
Make freesync continue to update planes even if vrr information
has already been changed
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underscan and ABM are connector properties but require updates
to DC stream state. Previously, on updates to these properties
the affected stream and all its planes were committed.
This is unnecessary; only a few fields on the stream need
to be changed.
[How]
If scaling or ABM have changed, change the stream and
create a stream update with those changes. Call
DC with only those fields.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace kzalloc() function with its 2-factor argument form, kcalloc().
This patch replaces cases of:
kzalloc(a * b, gfp)
with:
kcalloc(a, b, gfp)
Also, improve the coding style and the use of sizeof during
allocation by changing sizeof(struct dc_surface_update) and
sizeof(struct dc_plane_state) to sizeof(*updates) and
sizeof(*surfaces), correspondingly.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check if crtc state is changed so that mode set is
required before trying to create new stream.
It deals with the MST hotplug use case when plug back to the
same connector where the failure to create new stream for the
inactive crtc on the old connector.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Having the probe helper stuff (which pretty much everyone needs) in
the drm_crtc_helper.h file (which atomic drivers should never need) is
confusing. Split them out.
To make sure I actually achieved the goal here I went through all
drivers. And indeed, all atomic drivers are now free of
drm_crtc_helper.h includes.
v2: Make it compile. There was so much compile fail on arm drivers
that I figured I'll better not include any of the acks on v1.
v3: Massive rebase because i915 has lost a lot of drmP.h includes, but
not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h
there was still one, which this patch largely removes. Which means
rolling out lots more includes all over.
This will also conflict with ongoing drmP.h cleanup by others I
expect.
v3: Rebase on top of atomic bochs.
v4: Review from Laurent for bridge/rcar/omap/shmob/core bits:
- (re)move some of the added includes, use the better include files in
other places (all suggested from Laurent adopted unchanged).
- sort alphabetically
v5: Actually try to sort them, and while at it, sort all the ones I
touch.
v6: Rebase onto i915 changes.
v7: Rebase once more.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: virtualization@lists.linux-foundation.org
Cc: etnaviv@lists.freedesktop.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: spice-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-tegra@vger.kernel.org
Cc: xen-devel@lists.xen.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
[Why]
Backlight is conceptually a property of links, not streams.
All backlight programming is done on links, but there is a
stream property bl_pwm_level that is used to restore backlight
on dpms on and s3 resume. This is unnecessary, as backlight
is already restored by hardware with no driver intervention.
[How]
Remove bl_pwm_level, and the stream argument to set_backlight
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=109375
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 923fe49512)
[Why]
This fixes a stuttering issue that occurs when moving a hardware cursor
when VRR is enabled.
Previously when VRR is enabled atomic check will grab the connector
state for every atomic update. This has to lock the connector in order
to do so. The locking is bad enough by itself for performance, but
it gets worse with what we do just below that - add all the planes
for the CRTC to the commit.
This prevents the cursor fast path from working - there's more than one
plane now. With state->allow_modeset = true on top of this, it also
adds and removes all the planes from the DC context triggering a full
(very slow) update in DC.
[How]
We need the connector state to get the VRR min/max capbilities, but we
only need them when there's a CRTC mode change or when VRR is toggled.
The condition has been updated accordingly.
Fixes: 3cc22f281318 ("drm/amdgpu: Set FreeSync state using drm VRR properties")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] clarify dal input parameters to pplib interface, remove
un-used parameters. dal knows exactly which parameters needed
and their effects at pplib and smu sides.
current dal sequence for dcn1_update_clock to pplib:
1.smu10_display_clock_voltage_request for dcefclk
2.smu10_display_clock_voltage_request for fclk
3.phm_store_dal_configuration_data {
set_min_deep_sleep_dcfclk
set_active_display_count
store_cc6_data --- this data never be referenced
new sequence will be:
1. set_display_count --- need add new pplib interface
2. set_min_deep_sleep_dcfclk -- new pplib interface
3. set_hard_min_dcfclk_by_freq
4. set_hard_min_fclk_by_freq
after this code refactor, smu10_display_clock_voltage_request,
phm_store_dal_configuration_data will not be needed for rv.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
