To aid debugging of performance issues caused by limited PCIe
bandwidth print the PCIe link information on probe.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP locks record the owner when held, for PCIe devices the owner
ID will be the PCIe link number. When driver loads it should scan
known locks and if they indicate that they are held by local
endpoint but the driver doesn't hold them - release them.
Locks can be left taken for instance when kernel gets kexec-ed or
after a crash. Management FW tries to clean up stale locks too,
but it currently depends on PCIe link going down which doesn't
always happen.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic functions needed to implement offloading for filters
created by tc-flower.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds the capability of configuring the queue steering of arriving
packets based on their source and destination MAC addresses.
Source address steering (i.e. driving traffic to a specific queue),
for the i210, does not work, but filtering does (i.e. accepting
traffic based on the source address). So, trying to add a filter
specifying only a source address will be an error.
In practical terms this adds support for the following use cases,
characterized by these examples:
$ ethtool -N eth0 flow-type ether dst aa:aa:aa:aa:aa:aa action 0
(this will direct packets with destination address "aa:aa:aa:aa:aa:aa"
to the RX queue 0)
$ ethtool -N eth0 flow-type ether src 44:44:44:44:44:44 \
proto 0x22f0 action 3
(this will direct packets with source address "44:44:44:44:44:44" and
ethertype 0x22f0 to the RX queue 3)
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows igb_add_filter()/igb_erase_filter() to work on filters
that include MAC addresses (both source and destination).
For now, this only exposes the functionality, the next commit glues
ethtool into this. Later in this series, these APIs are used to allow
offloading of cls_flower filters.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Users expect that when adding a steering filter for the local MAC
address, that all the traffic directed to that address will go to some
queue.
Currently, it's not possible to configure entries in the "in use"
state, which is the normal state of the local MAC address entry (it is
the default), this patch allows to override the steering configuration
of "in use" entries, if the filter to be added match the address and
address type (source or destination) of an existing entry.
There is a bit of a special handling for entries referring to the
local MAC address, when they are removed, only the steering
configuration is reset.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some igb models (82575 and i210) the MAC address filters can
control to which queue the packet will be assigned.
This extends the 'state' with one more state to signify that queue
selection should be enabled for that filter.
As 82575 parts are no longer easily obtained (and this was developed
against i210), only support for the i210 model is enabled.
These functions are exported and will be used in the next patch.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Makes it possible to direct packets to queues based on their source
address. Documents the expected usage of the 'flags' parameter.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This will allow functionality depending on the hardware being traffic
class aware to work. In particular the tc-flower offloading checks
verifies that this bit is set.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On the RAH registers there are semantic differences on the meaning of
the "queue" parameter for traffic steering depending on the controller
model: there is the 82575 meaning, which "queue" means a RX Hardware
Queue, and the i350 meaning, where it is a reception pool.
The previous behaviour was having no effect for i210 based controllers
because the QSEL bit of the RAH register wasn't being set.
This patch separates the condition in discrete cases, so the different
handling is clearer.
Fixes: 83c21335c8 ("igb: improve MAC filter handling")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some MDIO busses will error out when trying to read a phy address with no
phy present at that address. In that case, probing the bus will fail
because __mdiobus_register() is scanning the bus for all possible phys
addresses.
In case MII_PHYSID1 returns -EIO or -ENODEV, consider there is no phy at
this address and set the phy ID to 0xffffffff which is then properly
handled in get_phy_device().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the order of the parameters passes to 'hlist_add_behind()' was
inverted, the 'parent' node was added "behind" the 'input', as input
is not in the list, this causes the 'input' node to be lost.
Fixes: 0e71def252 ("igb: add support of RX network flow classification")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original implementation for macvlan offload has us performing a full
port reset every time we added a new macvlan. This shouldn't be necessary
and can be avoided with a few behavior changes.
This patches updates the logic for the queues so that we have essentially 3
possible configurations for macvlan offload. They consist of 15 macvlans
with 4 queues per macvlan, 31 macvlans with 2 queues per macvlan, and 63
macvlans with 1 queue per macvlan. As macvlans are added you will encounter
up to 3 total resets if you add all the way up to 63, and after that the
device will stay in the mode supporting up to 63 macvlans until the L2FW
flag is cleared.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch drops the real_adapter member from the fwd_adapter structure.
The general idea behind the change is that the real_adapter is carrying
unnecessary data since we could always just grab the adapter structure
from netdev_priv(macvlan->lowerdev) if we really needed to get at it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Both the ixgbe and fm10k drivers support destination filtering.
Instead of adding a ton of complexity to support either source or passthru
mode we can instead just avoid offloading them for now. Doing this we avoid
leaking packets into interfaces that aren't meant to receive them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drop dead code now that we shouldn't be receiving broadcast or multicast
frames on the queues associated to the macvlan netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use a software path for packets that are
going to be locally switched between two macvlan interfaces on the same
device. In addition we resort to software replication of broadcast and
multicast packets instead of offloading that to hardware.
The general idea is that using the device for east/west traffic local to
the system is extremely inefficient. We can only support up to whatever the
PCIe limit is for any given device so this caps us at somewhere around 20G
for devices supported by ixgbe. This is compounded even further when you
take broadcast and multicast into account as a single 10G port can come to
a crawl as a packet is replicated up to 60+ times in some cases. In order
to get away from that I am implementing changes so that we handle
broadcast/multicast replication and east/west local traffic all in
software.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change renames the fwd_priv member to accel_priv as this more
accurately reflects the actual purpose of this value. In addition I am
adding an accessor which will allow us to further abstract this in the
future if needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drop the code for handling macvlan specific unicast lists. It isn't needed
since we don't take any efforts to maintain it when we bring the interface
up and it takes the slow path anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Comparison instruction requires a subtraction. If the constant
is negative we are more likely to fit it into a NFP instruction
directly if we change the sign and use addition.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
There are quite a few compare instructions now, use a table
to translate BPF instruction code to NFP instruction parameters
instead of parameterizing helpers. This saves LOC and makes
future extensions easier.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP instruction set can fit small immediates into the instruction.
Negative integers, however, will never fit because they will have
highest bit set. If we swap the ALU op between ADD and SUB and
negate the constant we have a better chance of fitting small negative
integers into the instruction itself and saving one or two cycles.
immed[gprB_21, 0xfffffffc]
alu[gprA_4, gprA_4, +, gprB_21], gpr_wrboth
immed[gprB_21, 0xffffffff]
alu[gprA_5, gprA_5, +carry, gprB_21], gpr_wrboth
now becomes:
alu[gprA_4, gprA_4, -, 4], gpr_wrboth
alu[gprA_5, gprA_5, -carry, 0], gpr_wrboth
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Swap VF representor tx and rx interface statistics since it is a
virtual switchdev port and tx for VM should be rx for VF representor
and vice-versa.
Signed-off-by: Srinivas Jampala <srinivasa.jampala@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-04-24
This series contains fixes to ixgbevf, igb and ice drivers.
Colin Ian King fixes the return value on error for the new XDP support
that went into ixgbevf for 4.17.
Vinicius provides a fix for queue 0 for igb, which was not receiving all
the credits it needed when QAV mode was enabled.
Anirudh provides several fixes for the new ice driver, starting with
properly initializing num_nodes_added to zero. Fixed up a code comment
to better reflect what is really going on in the code. Fixed how to
detect if an OICR interrupt has occurred to a more reliable method.
Md Fahad fixes the ice driver to allocate the right amount of memory
when reading and storing the devices MAC addresses. The device can have
up to 2 MAC addresses (LAN and WoL), while WoL is currently not
supported, we need to ensure it can be properly handled when support is
added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The check port->rev_info.major >= 6 is being performed twice, thus
the inner second check is always true and is redundant, hence it
can be removed. Detected by cppcheck.
drivers/net/ethernet/freescale/fman/fman_port.c:1394]: (warning)
Identical inner 'if' condition is always true.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the MAC read operation, the device can return up to two (LAN and WoL)
MAC addresses. Without access to adequate memory, the device will return
an error. Fixed this by allocating the right amount of memory. Also, logic
to detect and copy the LAN MAC address into the port_info structure has
been added. Note that the WoL MAC address is ignored currently as the WoL
feature isn't supported yet.
Fixes: dc49c77236 ("ice: Get MAC/PHY/link info and scheduler topology")
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The strscpy() was a recent fix (net: qed: use correct strncpy() size) to
prevent passing the length of the source buffer to strncpy() and guarantee
null termination.
It misses the goal of overwriting only the first 3 characters in
"???_BIG_RAM" and "???_RAM" while keeping the rest of the string.
Use strncpy() with the length of 3, without null termination.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Associate an arbitrary ID with each ARFS filter, allowing to properly query
for expiry. The association is maintained in a hash table, which is
protected by a spinlock.
v3: fix build warnings when CONFIG_RFS_ACCEL is disabled (thanks lkp-robot).
v2: fixed uninitialised variable (thanks davem and lkp-robot).
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware spec, checking the INTEVENT bit isn't a
reliable way to detect if an OICR interrupt has occurred. This is
because this bit can be cleared by the hardware/firmware before the
interrupt service routine has run. So instead, just check for OICR
events every time.
Fixes: 940b61af02 ("ice: Initialize PF and setup miscellaneous interrupt")
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Action type 5 defines large action generic values. Fix comment to
reflect that better.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_sched_add_nodes_to_layer is used recursively, and so we start
with num_nodes_added being 0. This way, in case of an error or if
num_nodes is NULL, the function just returns 0 to indicate that no
nodes were added.
Fixes: 5513b920a4 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When Qav mode is enabled, queue 0 should be kept on Stream Reservation
mode. From the i210 datasheet, section 8.12.19:
"Note: Queue0 QueueMode must be set to 1b when TransmitMode is set to
Qav." ("QueueMode 1b" represents the Stream Reservation mode)
The solution is to give queue 0 the all the credits it might need, so
it has priority over queue 1.
A situation where this can happen is when cbs is "installed" only on
queue 1, leaving queue 0 alone. For example:
$ tc qdisc replace dev enp2s0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0
$ tc qdisc replace dev enp2s0 parent 100:2 cbs locredit -1470 \
hicredit 30 sendslope -980000 idleslope 20000 offload 1
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current error handling for failed resource setup for xdp_ring
data is a break out of the loop and returning 0 indicated everything
was OK, when in fact it is not. Fix this by exiting via the
error exit label err_setup_tx that will clean up the resources
correctly and return and error status.
Detected by CoverityScan, CID#1466879 ("Logically dead code")
Fixes: 21092e9ce8 ("ixgbevf: Add support for XDP_TX action")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for adaptive TX moderation. This greatly reduces TX interrupt
rate and increases bandwidth, mostly for TCP bandwidth over ARM
architecture (below). There is a slight single stream TCP with very large
message sizes degradation (x86). In this case if there's any moderation on
transmitted packets the bandwidth would reduce due to hitting TCP output limit.
Since this is a synthetic case, this is still worth doing.
Performance improvement (ConnectX-4Lx 40GbE, ARM)
TCP 64B bandwidth with 1-50 streams increased 6-35%.
TCP 64B bandwidth with 100-500 streams increased 20-70%.
Performance improvement (ConnectX-5 100GbE, x86)
Bandwidth: increased up to 40% (1024B with 10s of streams).
Interrupt rate: reduced up to 50% (1024B with 1000s of streams).
Performance degradation (ConnectX-5 100GbE, x86)
Bandwidth: up to 10% decrease single stream TCP (1MB message size from
51Gb/s to 47Gb/s).
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for introducing adaptive TX to net DIM.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same fix in Commit dbe173079a ("bridge: fix netconsole
setup over bridge") is also needed for team driver.
While at it, remove the unnecessary parameter *team from
team_port_enable_netpoll().
v1->v2:
- fix it in a better way, as does bridge.
Fixes: 0fb52a27a0 ("team: cleanup netpoll clode")
Reported-by: João Avelino Bellomo Filho <jbellomo@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some HP laptops have only a single wifi antenna. This would not be a
problem except that they were shipped with an incorrectly encoded
EFUSE. It should have been possible to open the computer and transfer
the antenna connection to the other terminal except that such action
might void the warranty, and moving the antenna broke the Windows
driver. The fix was to add a module option that would override the
EFUSE encoding. That was done with commit c18d8f5095 ("rtlwifi:
rtl8723be: Add antenna select module parameter"). There was still a
problem with Bluetooth coexistence, which was addressed with commit
baa1702290 ("rtlwifi: btcoexist: Implement antenna selection").
There were still problems, thus there were commit 0ff78adeef
("rtlwifi: rtl8723be: fix ant_sel code") and commit 6d62269283
("rtlwifi: btcoexist: Fix antenna selection code"). Despite all these
attempts at fixing the problem, the code is not yet right. A proper
fix is important as there are now instances of laptops having
RTL8723DE chips with the same problem.
The module parameter ant_sel is used to control antenna number and path.
At present enum ANT_{X2,X1} is used to define the antenna number, but
this choice is not intuitive, thus change to a new enum ANT_{MAIN,AUX}
to make it more readable. This change showed examples where incorrect
values were used. It was also possible to remove a workaround in
halbtcoutsrc.c.
The experimental results with single antenna connected to specific path
are now as follows:
ant_sel ANT_MAIN(#1) ANT_AUX(#2)
0 -8 -62
1 -62 -10
2 -6 -60
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Fixes: c18d8f5095 ("rtlwifi: rtl8723be: Add antenna select module parameter")
Fixes: baa1702290 ("rtlwifi: btcoexist: Implement antenna selection")
Fixes: 0ff78adeef ("rtlwifi: rtl8723be: fix ant_sel code")
Fixes: 6d62269283 ("rtlwifi: btcoexist: Fix antenna selection code")
Cc: Stable <stable@vger.kernel.org> # 4.7+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When version 8 of the scan command API was introduced, only the size
of version 7 was updated, causing older versions of the firmware to
throw BAD_COMMAND errors.
Calculating the old version based on the size of the latest version
got too complicated and the size of the older versions will never
change anyway, so it's better to just hardcoded the sizes.
Fixes: 66fa2424df ("iwlwifi: fw api: support the new scan request FW API version")
Reported-by: Scott Register <sreg@sreg.io>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must validate sockaddr_len, otherwise userspace can pass fewer data
than we expect and we end up accessing invalid data.
Fixes: 224cf5ad14 ("ppp: Move the PPP drivers")
Reported-by: syzbot+4f03bdf92fdf9ef5ddab@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().
Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration information is added to the debug data collection, in
addition to register dump.
Added qed_dbg_nvm_image() that receives an image type, allocates a
buffer and reads the image. The images are saved in the buffers and the
dump size is updated.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nvm images attributes are cached during driver load, acquiring ptt
is not needed when calling qed_mcp_get_nvm_image().
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the core version detection to a common place ("hwif.c") and
implement a table which can be used to lookup the correct callbacks for
each IP version.
This simplifies the initialization flow of each IP version and eases
future implementation of new IP versions.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no benefit in using netif_info et al before the net_device has
been registered. We get messages like
r8169 0000:03:00.0 (unnamed net_device) (uninitialized): [message]
Therefore use dev_info/dev_err instead.
As a side effect we don't need parameter dev for function
rtl8169_get_mac_version() any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Commit 8a8efa22f5 ("bonding: sync netpoll code with bridge"), it
would set slave_dev npinfo in slave_enable_netpoll when enslaving a dev
if bond->dev->npinfo was set.
However now slave_dev npinfo is set with bond->dev->npinfo before calling
slave_enable_netpoll. With slave_dev npinfo set, __netpoll_setup called
in slave_enable_netpoll will not call slave dev's .ndo_netpoll_setup().
It causes that the lower dev of this slave dev can't set its npinfo.
One way to reproduce it:
# modprobe bonding
# brctl addbr br0
# brctl addif br0 eth1
# ifconfig bond0 192.168.122.1/24 up
# ifenslave bond0 eth2
# systemctl restart netconsole
# ifenslave bond0 br0
# ifconfig eth2 down
# systemctl restart netconsole
The netpoll won't really work.
This patch is to remove that slave_dev npinfo setting in bond_enslave().
Fixes: 8a8efa22f5 ("bonding: sync netpoll code with bridge")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6870de435b ("bpf: make virtio compatible w/
bpf_xdp_adjust_tail") i didn't account for vi->hdr_len during new
packet's length calculation after bpf_prog_run in receive_mergeable.
because of this all packets, if they were passed to the kernel,
were truncated by 12 bytes.
Fixes:6870de435b90 ("bpf: make virtio compatible w/ bpf_xdp_adjust_tail")
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Avoid using value stored in the login response buffer when
cleaning TX and RX buffer pools since these could be inconsistent
depending on the device state. Instead use the field in the driver's
private data that tracks the number of active pools.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion of rndis friendly name to utf8 uses a standard
kernel routine which is optional in config. Therefore build
would fail for some configurations. Resolve by selecting needed
library.
Fixes: 0fe554a46a ("hv_netvsc: propogate Hyper-V friendly name into interface alias")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-04-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Initial work on BPF Type Format (BTF) is added, which is a meta
data format which describes the data types of BPF programs / maps.
BTF has its roots from CTF (Compact C-Type format) with a number
of changes to it. First use case is to provide a generic pretty
print capability for BPF maps inspection, later work will also
add BTF to bpftool. pahole support to convert dwarf to BTF will
be upstreamed as well (https://github.com/iamkafai/pahole/tree/btf),
from Martin.
2) Add a new xdp_bpf_adjust_tail() BPF helper for XDP that allows
for changing the data_end pointer. Only shrinking is currently
supported which helps for crafting ICMP control messages. Minor
changes in drivers have been added where needed so they recalc
the packet's length also when data_end was adjusted, from Nikita.
3) Improve bpftool to make it easier to feed hex bytes via cmdline
for map operations, from Quentin.
4) Add support for various missing BPF prog types and attach types
that have been added to kernel recently but neither to bpftool
nor libbpf yet. Doc and bash completion updates have been added
as well for bpftool, from Andrey.
5) Proper fix for avoiding to leak info stored in frame data on page
reuse for the two bpf_xdp_adjust_{head,meta} helpers by disallowing
to move the pointers into struct xdp_frame area, from Jesper.
6) Follow-up compile fix from BTF in order to include stdbool.h in
libbpf, from Björn.
7) Few fixes in BPF sample code, that is, a typo on the netdevice
in a comment and fixup proper dump of XDP action code in the
tracepoint exception, from Wang and Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tun driver, in absence of an eBPF steering program,
always compute the rxhash in its rx path, even when such value
is later unused due to additional checks (
This changeset moves the all the related checks just before the
__skb_get_hash_symmetric(), so that the latter is no more computed
when unneeded.
Also replace an unneeded RCU section with rcu_access_pointer().
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to dump lan78xx family registers using ethtool, add
support at lan78xx driver level.
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:
0=link/activity 1=link1000/activity
2=link100/activity 3=link10/activity
4=link100/1000/activity 5=link10/1000/activity
6=link10/100/activity 14=off 15=on
These values are given symbolic constants in a dt-bindings header.
Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a standard mechanism for locating and using a MAC address from
the Device Tree. Use this facility in the lan78xx driver to support
applications without programmed EEPROM or OTP. At the same time,
regularise the handling of the different address sources.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpumask_local_spread to provide interrupt affinity hints
for each queue. This will spread interrupts across NUMA local
CPUs first, extending to remote nodes if needed.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be a need for VF driver to request PF to explicitly update its
bulletin with a MAC address.
e.g. When user assigns a MAC address to VF while VF is still down,
and PF's bulletin board contains different MAC address, in this case,
when VF's interface is brought up, it gets loaded with MAC address from
bulletin board which is not desirable.
To handle this corner case, we need a new TLV to request PF to update
its bulletin board with suggested MAC.
This request will be honored only for trusted VFs.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per existing behavior, when PF sets a MAC address for a VF
(also called as forced MAC), VF is not allowed to change its
MAC address afterwards.
This puts the limitation on few use cases such as bonding of VFs,
where bonding driver asks VF to change its MAC address.
This patch uses a VF trust mode to allow VF to change its MAC address
in spite PF has set a forced MAC for that VF.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, on a new link creation or when 'remote' address parameter
is updated, an MTU is not changed and always equals 1500. When a lower
device has a larger MTU, it might not be efficient, e.g. for UDP, and
requires the manual MTU adjustments to match the MTU of the lower
device.
This patch tries to automate this process, finds a lower device using
the 'remote' address parameter, then uses its MTU to tune GENEVE's MTU:
* on a new link creation
* when 'remote' parameter is changed
Also with this patch, the MTU from a user, on a new link creation, is
passed to geneve_change_mtu() where it is verified, and MTU adjustments
with a lower device is skipped in that case. Prior that change, it was
possible to set the invalid MTU values on a new link creation.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_change_mtu() will be used not only as ndo_change_mtu() callback,
but also to verify a user specified MTU on a new link creation in the
next patch.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ETH_HLEN instead and introduce two new macros: GENEVE_IPV4_HLEN
and GENEVE_IPV6_HLEN that include Ethernet header length, corresponded
IP header length and GENEVE_BASE_HLEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Account for operational state when determining port linkup state,
as per Documentation/networking/operstates.txt.
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the ndo to gather VF statistics through the PF.
Collect VF statistics via mailbox from VF.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for specifying system controller that configures
phy-mode setting.
According to the DT property "phy-mode", it's necessary to configure the
controller, which is used to choose the settings of the MAC suitable,
for example, mdio pin connections, internal clocks, and so on.
Supported phy-modes are SoC-dependent. The driver allows phy-mode to set
"internal" if the SoC has a built-in PHY, and {"mii", "rmii", "rgmii"}
if the SoC supports each mode. So we have to check whether the phy-mode
is valid or not.
This adds the following features for each SoC:
- check whether the SoC supports the specified phy-mode
- configure the controller accroding to phy-mode
The DT property accepts one argument to distinguish them for multiple MAC
instances.
ethernet@65000000 {
...
socionext,syscon-phy-mode = <&soc_glue 0>;
};
ethernet@65200000 {
...
socionext,syscon-phy-mode = <&soc_glue 1>;
};
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link is becoming up for Pro4 SoC, the kernel is stalled
due to some missing clocks and resets.
The AVE block for Pro4 is connected to the GIO bus in the SoC.
Without its clock/reset, the access to the AVE register makes the
system stall.
In the same way, another MAC clock for Giga-bit Connection and
the PHY clock are also required for Pro4 to activate the Giga-bit feature
and to recognize the PHY.
To satisfy these requirements, this patch adds support for multiple clocks
and resets, and adds the clock-names and reset-names to the binding because
we need to distinguish clock/reset for the AVE main block and the others.
Also, make the resets a required property. Currently, "reset is
optional" relies on that the bootloader or firmware has deasserted
the reset before booting the kernel. Drivers should work without
such expectation.
Fixes: 4c270b55a5 ("net: ethernet: socionext: add AVE ethernet driver")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_register will search for any mdiobus board info registered for
the bus being registered. If found, it will probe devices on the bus.
That device, if for example it is an ethernet switch, may then try to
register an mdio bus. Thus we need to allow recursive calls to
mdiobus_register.
Holding the mdio_board_lock will cause a deadlock during this
recursion. Release the lock and use list_for_each_entry_safe.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver. This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.
Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096. Move the kzalloc() call
into the bnxt_get_pkgver() function.
Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
offloads is a buffer in virtio format, should use
the __virtio64 tag.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Programming vids (adding or removing them) still passes
guest-endian values in the DMA buffer. That's wrong
if guest is big-endian and when virtio 1 is enabled.
Note: this is on top of a previous patch:
virtio_net: split out ctrl buffer
Fixes: 9465a7a6f ("virtio_net: enable v1.0 support")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending control commands, virtio net sets up several buffers for
DMA. The buffers are all part of the net device which means it's
actually allocated by kvmalloc so it's in theory (on extreme memory
pressure) possible to get a vmalloc'ed buffer which on some platforms
means we can't DMA there.
Fix up by moving the DMA buffers into a separate structure.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When longer interface names are used, the action names exposed in
/proc/interrupts and /proc/irq/* maybe truncated. For example, when
using the predictable name algorithm in systemd on a HiSilicon D05,
I see:
ubuntu@d05-3:~$ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
enahisic2i0-tx0
enahisic2i0-tx1
[...]
enahisic2i0-tx8
enahisic2i0-tx9
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
Increase the max ring name length to allow for an interface name
of IFNAMSIZE. After this change, I now see:
$ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
enahisic2i0-tx0
enahisic2i0-tx1
enahisic2i0-tx2
[...]
enahisic2i0-tx8
enahisic2i0-tx9
enahisic2i0-tx10
enahisic2i0-tx11
enahisic2i0-tx12
enahisic2i0-tx13
enahisic2i0-tx14
enahisic2i0-tx15
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add platform device driver to populate the ax88796 platform data from
information provided by the XSurf100 zorro device driver. The ax88796
module will be loaded through this module's probe function.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net device struct pointer is stored as platform device drvdata on
module probe - clear the drvdata entry on probe fail there, as well as
when unloading the module.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Amiga X-Surf100, the network card interrupt is shared with many
other interrupt sources, so requires the IRQF_SHARED flag to register.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to tell the ax88796 driver whether it is sensible to enter
the 8390 interrupt handler, an "is this interrupt caused by the 88796"
callback has been added to the ax_plat_data structure (with NULL being
compatible to the previous behaviour).
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add platform specific hooks for block transfer reads/writes of packet
buffer data, superseding the default provided ax_block_input/output.
Currently used for m68k Amiga XSurf100.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This complements the fix in 82533ad9a1 ("net: ethernet: ax88796:
don't call free_irq without request_irq first") that removed the
free_irq call in the error path of probe, to also not call free_irq
when remove is called to revert the effects of probe.
Fixes: 82533ad9a1 (net: ethernet: ax88796: don't call free_irq without request_irq first)
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call ax_mii_init in ax_open(), and unregister/remove mdiobus resources
in ax_close().
This is needed to be able to unload the module, as the module is busy
while the MII bus is attached.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To read the MAC address from the (virtual) SAprom, the remote DMA
unit needs to be set up like for every other process access to card-local
memory.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Asix Electronics PHY found on the X-Surf 100 Amiga Zorro network
card by Individual Computers is buggy, and needs the reset bit toggled
as workaround to make a PHY soft reset succeed.
Add workaround driver just for this special case.
Suggested in xsurf100 patch series review by Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform data header file is now unused. Remove it, but add
an extra include which it brought in.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the allocation of this structure to the probe function is a
step towards making it the core data structure of the driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the code, removing the need to handle active low
flags, etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio-gpio driver was the only user of the interface reset option.
Since it no longer uses it, remove it from the bit banging code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform data can contain a function to call to reset
the bit banging interface. It is not used, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the prefix for fib6_info struct elements from rt6i_ to fib6_.
rt6i_pcpu and rt6i_exception_bucket are left as is given that they
point to rt6_info entries.
Rename only; not functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3_get_hdr_len() is used to calculate the header length which in
turn is used to calculate the gso_size for skb. When rxvlan offload is
disabled, vlan tag is present in the header and the function references
ip header from sizeof(ethhdr) and leads to incorrect pointer reference.
This patch fixes this issue by taking sizeof(vlan_ethhdr) into account
if vlan tag is present and correctly references the ip hdr.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Acked-by: Louis Luo <llouis@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables arm64 platform support for the HINIC driver.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ACS Feature is currently enabled for GMAC >= 4 but the llc_snap status
is never checked in descriptor rx_status callback. This will cause
stmmac to always strip packets even that ACS feature is already
stripping them.
Lets be safe and disable the ACS feature for GMAC >= 4 and always strip
the packets for this GMAC version.
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2 TX/RX descriptors uses 40bits DMA addresses, but 41 bits masks were
used (GENMASK_ULL(40, 0)).
This commit fixes that by using the correct mask.
Fixes: e7c5359f2e ("net: mvpp2: introduce PPv2.2 HW descriptors and adapt accessors")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the last rmnet device attached to a real device is removed, the
real device is unregistered from rmnet. As a result, the real device
lookup fails resulting in a warning when the fill_info handler is
called as part of the rmnet device unregistration.
Fix this by returning the rmnet flags as 0 when no real device is
present.
WARNING: CPU: 0 PID: 1779 at net/core/rtnetlink.c:3254
rtmsg_ifinfo_build_skb+0xca/0x10d
Modules linked in:
CPU: 0 PID: 1779 Comm: ip Not tainted 4.16.0-11872-g7ce2367 #1
Stack:
7fe655f0 60371ea3 00000000 00000000
60282bc6 6006b116 7fe65600 60371ee8
7fe65660 6003a68c 00000000 900000000
Call Trace:
[<6006b116>] ? printk+0x0/0x94
[<6001f375>] show_stack+0xfe/0x158
[<60371ea3>] ? dump_stack_print_info+0xe8/0xf1
[<60282bc6>] ? rtmsg_ifinfo_build_skb+0xca/0x10d
[<6006b116>] ? printk+0x0/0x94
[<60371ee8>] dump_stack+0x2a/0x2c
[<6003a68c>] __warn+0x10e/0x13e
[<6003a82c>] warn_slowpath_null+0x48/0x4f
[<60282bc6>] rtmsg_ifinfo_build_skb+0xca/0x10d
[<60282c4d>] rtmsg_ifinfo_event.part.37+0x1e/0x43
[<60282c2f>] ? rtmsg_ifinfo_event.part.37+0x0/0x43
[<60282d03>] rtmsg_ifinfo+0x24/0x28
[<60264e86>] dev_close_many+0xba/0x119
[<60282cdf>] ? rtmsg_ifinfo+0x0/0x28
[<6027c225>] ? rtnl_is_locked+0x0/0x1c
[<6026ca67>] rollback_registered_many+0x1ae/0x4ae
[<600314be>] ? unblock_signals+0x0/0xae
[<6026cdc0>] ? unregister_netdevice_queue+0x19/0xec
[<6026ceec>] unregister_netdevice_many+0x21/0xa1
[<6027c765>] rtnl_delete_link+0x3e/0x4e
[<60280ecb>] rtnl_dellink+0x262/0x29c
[<6027c241>] ? rtnl_get_link+0x0/0x3e
[<6027f867>] rtnetlink_rcv_msg+0x235/0x274
Fixes: be81a85f5f ("net: qualcomm: rmnet: Implement fill_info")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the NetVSP v6 and 6.1 message structures, and includes
these versions into NetVSC/NetVSP version negotiation process.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement the 'Device Naming' feature of the Hyper-V
network device API. In Hyper-V on the host through the GUI or PowerShell
it is possible to enable the device naming feature which causes
the host to make available to the guest the name of the device.
This shows up in the RNDIS protocol as the friendly name.
The name has no particular meaning and is limited to 256 characters.
The value can only be set via PowerShell on the host, but could
be scripted for mass deployments. The default value is the
string 'Network Adapter' and since that is the same for all devices
and useless, the driver ignores it.
In Windows, the value goes into a registry key for use in SNMP
ifAlias. For Linux, this patch puts the value in the network
device alias property; where it is visible in ip tools and SNMP.
The host provided ifAlias is just a suggestion, and can be
overridden by later ip commands.
Also requires exporting dev_set_alias in netdev core.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the chip configuration entries only RTL8169 (ver <= 06)
supports tx checksumming for jumbo packets.
By the way: constant JUMBO_1K is a little misleading because it refers
to the standard packet size and not to a jumbo packet size.
By implementing this rule we can get rid of configuring tx checksumming
support per chip type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The region to be used is always the first of type IORESOURCE_MEM.
We can implement this rule directly w/o having to specify which
region is the first one per configuration entry.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
txd_version is used in rtl_init_one() only, so we can drop member
txd_version from struct rtl8169_private.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain entries in array mac_info[] are redundant, so remove them:
0x7cf, 0x2c200000 (VER 33): matched by entry 0x7c8, 0x2c000000
0x7cf, 0x28300000 (VER 26): matched by entry 0x7c8, 0x28000000
0x7cf, 0x3cb00000 (VER 24): matched by entry 0x7c8, 0x3c800000
0x7cf, 0x3c400000 (VER 22): matched by entry 0x7c8, 0x3c000000
0x7cf, 0x38500000 (VER 17): matched by entry 0x7c8, 0x38000000
0x7cf, 0x44900000 (VER 39): matched by entry 0x7c8, 0x44800000
0x7cf, 0x40b00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x40a00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x34a00000 (VER 09): matched by entry 0x7c8, 0x34800000
0x7cf, 0x24a00000 (VER 09): matched by entry 0x7c8, 0x24800000
In addition don't mask out bits 30 and 29 when printing the XID.
Most likely this is a relict from the times when the driver covered
RTL8169 chip version only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For security reasons since commit ad67b74d24 "printk: hash addresses
printed with %p" %p doesn't display the full address any longer.
We could switch to %px, but I think the pointer address doesn't
provide a real benefit, so remove printing the hashed address.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can get rid of member opts1_mask and in addition save a few cpu
cycles in the hot path of rtl_rx().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code can be a little simplified by switching the interrupt handler
argument type to struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter handling functions don't deal with the net_device, so code
can be simplified by changing the argument type to
struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code can be simplified by changing the argument type of hw_start
callbacks from struct net_device * to struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is very simple and used only once, so we can inline
the two statements.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_buf_sz is constant, so we don't have to pass it as parameter and
in general can replace it with a constant.
When working on this I noticed that also before in
rtl_set_rx_max_size() a value of 0x4000 is set, what is not in line
with the chip spec. According to the spec only bits 0..13 are used
and we set an effective value of zero therefore.
However, the driver still seems to work and due to potential side
effects I'm reluctant to make a change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_rx_fill() is called only once and directly before the call
array tp->Rx_databuff[] is filled with zero's. Therefore we don't
need this check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function doesn't use the net_device, therefore change the
parameter to type struct rtl8169_private * to simplify the code.
In addition we don't need the calculations in the memset
statements, we can use the size of the arrays directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->dev.parent has the same value as tp_to_dev(tp)
(set by SET_NETDEV_DEV() in rtl_init_one()) and we know it can't be NULL.
This allows us to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_schedule() is called from hard irq context, so we can switch to
napi_schedule_irqoff() and avoid some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use generic constant NAPI_POLL_WAIT instead of defining an own
constant for the same value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not a giant leap for mankind, but let's avoid the open-coded memcpy
and use standard helper skb_copy_to_linear_data instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6f0333b8fd "r8169: use 50% less ram for RX ring" member
align isn't used any longer, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Member features of struct rtl8169_private isn't used any longer since
commit 6c6aa15fde "r8169: improve interrupt handling", so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for promiscuous mode in k2g's network
driver. When upper layer instructs to transition from
non-promiscuous mode to promiscuous mode or vice versa
K2G network driver needs to configure ALE accordingly
so that in case of non-promiscuous mode, ALE will not flood
all unicast packets to host port, while in promiscuous
mode, it will pass all received unicast packets to
host port.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an API to support setting rx mode in
netcp modules. If a netcp module needs to be notified
when upper layer transitions from one rx mode to
another and react accordingly, such a module will implement
the new API set_rx_mode added in this patch. Currently
rx modes supported are PROMISCUOUS and NON_PROMISCUOUS
modes.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp driver shouldn't proceed until the knav qmss and dma
devices are ready. So return -EPROBE_DEFER if these devices are not
ready.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the probe sequence is not guaranteed contrary to the assumption
of the commit 2d8e276a9030, same has to be reverted.
commit 2d8e276a9030 ("net: netcp: remove dead code from the driver")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy used for K2G allows for internal delays to be added optionally
to the clock circuitry based on board desing. To add this support,
enhance the driver to use of_get_phy_mode() to read the phy-mode from
the phy device and pass the same to phy through of_phy_connect().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stats block in 2u cpsw hardware is similar to the one on nu
and hence handle it in a similar way by using a macro that includes
2u hardware as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently support only vlan priority zero. So map the
vlan priorities to zero flow in hardware.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce rgmii link status to handle link state events for 2u
cpsw hardware on K2G.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2u cpsw hardware on K2G uses rgmii link to interface with Phy. So add
support for this interface in the code so that driver can be re-used
for 2u hardware.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add support for 2u cpsw hardware found on
K2G SoC, make sgmii configuration conditional. This is required
since 2u uses RGMII interface instead of SGMII and to allow for driver
re-use.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver currently uses macro for NU and XBE hardwrae, while other
places for older hardware such as that on K2H/K SoC (version 1.4
of the cpsw hardware, it explicitly check for the ss_version
inline. Add a new macro for version 1.4 and use it to customize
code in the driver. While at it also fix similar issue with
checking XBE version by re-using existing macro IS_SS_ID_XGBE().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
w/ bpf_xdp_adjust_tail helper xdp's data_end pointer could be changed as
well (only "decrease" of pointer's location is going to be supported).
changing of this pointer will change packet's size.
for virtio driver we need to adjust XDP_PASS handling by recalculating
length of the packet if it was passed to the TCP/IP stack
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
w/ bpf_xdp_adjust_tail helper xdp's data_end pointer could be changed as
well (only "decrease" of pointer's location is going to be supported).
changing of this pointer will change packet's size.
for tun driver we need to adjust XDP_PASS handling by recalculating
length of the packet if it was passed to the TCP/IP stack
(in case if after xdp's prog run data_end pointer was adjusted)
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
w/ bpf_xdp_adjust_tail helper xdp's data_end pointer could be changed as
well (only "decrease" of pointer's location is going to be supported).
changing of this pointer will change packet's size.
for nfp driver we will just calculate packet's length unconditionally
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
w/ bpf_xdp_adjust_tail helper xdp's data_end pointer could be changed as
well (only "decrease" of pointer's location is going to be supported).
changing of this pointer will change packet's size.
for cavium's thunder driver we will just calculate packet's length
unconditionally
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
w/ bpf_xdp_adjust_tail helper xdp's data_end pointer could be changed as
well (only "decrease" of pointer's location is going to be supported).
changing of this pointer will change packet's size.
for bnxt driver we will just calculate packet's length unconditionally
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
w/ bpf_xdp_adjust_tail helper xdp's data_end pointer could be changed as
well (only "decrease" of pointer's location is going to be supported).
changing of this pointer will change packet's size.
for mlx4 driver we will just calculate packet's length unconditionally
(the same way as it's already being done in mlx5)
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Bogus trimming in tun_net_xmit() causes truncated vlan packets.
skb->len is correct whether or not skb_vlan_tag_present() is true. There
is no more reason to adjust the skb length on xmit in this driver than
any other driver. tun_put_user() adds 4 bytes to the total for tagged
packets because it transmits the tag inline to userspace. This is
similar to a nic transmitting the tag inline on the wire.
Reproducing the bug by sending any tagged packet through back-to-back
connected tap interfaces:
socat TUN,tun-type=tap,iff-up,tun-name=in TUN,tun-type=tap,iff-up,tun-name=out &
ip link add link in name in.20 type vlan id 20
ip addr add 10.9.9.9/24 dev in.20
ip link set in.20 up
tshark -nxxi in -f arp -c1 2>/dev/null &
tshark -nxxi out -f arp -c1 2>/dev/null &
ping -c 1 10.9.9.5 >/dev/null 2>&1
The output from the 'in' and 'out' interfaces are different when the
bug is present:
Capturing on 'in'
0000 ff ff ff ff ff ff 76 cf 76 37 d5 0a 81 00 00 14 ......v.v7......
0010 08 06 00 01 08 00 06 04 00 01 76 cf 76 37 d5 0a ..........v.v7..
0020 0a 09 09 09 00 00 00 00 00 00 0a 09 09 05 ..............
Capturing on 'out'
0000 ff ff ff ff ff ff 76 cf 76 37 d5 0a 81 00 00 14 ......v.v7......
0010 08 06 00 01 08 00 06 04 00 01 76 cf 76 37 d5 0a ..........v.v7..
0020 0a 09 09 09 00 00 00 00 00 00 ..........
Fixes: aff3d70a07 ("tun: allow to attach ebpf socket filter")
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all code paths referencing a FIB entry from
rt6_info to fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce fib6_nh structure and move nexthop related data from
rt6_info and rt6_info.dst to fib6_nh. References to dev, gateway or
lwtstate from a FIB lookup perspective are converted to use fib6_nh;
datapath references to dst version are left as is.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch removes rt6i_table from rt6_info. Save the ipv6
table for a VRF in net_vrf. fib tables can not be deleted so
no reference counting or locking is required.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some firmware variants - specifically 'capture packed stream' - RSS
filters are not valid. We must check if RSS is actually active rather
than merely enabled.
Fixes: 42356d9a13 ("sfc: support RSS spreading of ethtool ntuple filters")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like tos inherit, ttl inherit should also means inherit the inner protocol's
ttl values, which actually not implemented in vxlan yet.
But we could not treat ttl == 0 as "use the inner TTL", because that would be
used also when the "ttl" option is not specified and that would be a behavior
change, and breaking real use cases.
So add a different attribute IFLA_VXLAN_TTL_INHERIT when "ttl inherit" is
specified with ip cmd.
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing API ndo_xdp_xmit to take a struct xdp_frame instead of struct
xdp_buff. This brings xdp_return_frame and ndp_xdp_xmit in sync.
This builds towards changing the API further to become a bulk API,
because xdp_buff is not a queue-able object while xdp_frame is.
V4: Adjust for commit 59655a5b6c ("tuntap: XDP_TX can use native XDP")
V7: Adjust for commit d9314c474d ("i40e: add support for XDP_REDIRECT")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing API xdp_return_frame() to take struct xdp_frame as argument,
seems like a natural choice. But there are some subtle performance
details here that needs extra care, which is a deliberate choice.
When de-referencing xdp_frame on a remote CPU during DMA-TX
completion, result in the cache-line is change to "Shared"
state. Later when the page is reused for RX, then this xdp_frame
cache-line is written, which change the state to "Modified".
This situation already happens (naturally) for, virtio_net, tun and
cpumap as the xdp_frame pointer is the queued object. In tun and
cpumap, the ptr_ring is used for efficiently transferring cache-lines
(with pointers) between CPUs. Thus, the only option is to
de-referencing xdp_frame.
It is only the ixgbe driver that had an optimization, in which it can
avoid doing the de-reference of xdp_frame. The driver already have
TX-ring queue, which (in case of remote DMA-TX completion) have to be
transferred between CPUs anyhow. In this data area, we stored a
struct xdp_mem_info and a data pointer, which allowed us to avoid
de-referencing xdp_frame.
To compensate for this, a prefetchw is used for telling the cache
coherency protocol about our access pattern. My benchmarks show that
this prefetchw is enough to compensate the ixgbe driver.
V7: Adjust for commit d9314c474d ("i40e: add support for XDP_REDIRECT")
V8: Adjust for commit bd658dda42 ("net/mlx5e: Separate dma base address
and offset in dma_sync call")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch shows how it is possible to have both the driver local page
cache, which uses elevated refcnt for "catching"/avoiding SKB
put_page returns the page through the page allocator. And at the
same time, have pages getting returned to the page_pool from
ndp_xdp_xmit DMA completion.
The performance improvement for XDP_REDIRECT in this patch is really
good. Especially considering that (currently) the xdp_return_frame
API and page_pool_put_page() does per frame operations of both
rhashtable ID-lookup and locked return into (page_pool) ptr_ring.
(It is the plan to remove these per frame operation in a followup
patchset).
The benchmark performed was RX on mlx5 and XDP_REDIRECT out ixgbe,
with xdp_redirect_map (using devmap) . And the target/maximum
capability of ixgbe is 13Mpps (on this HW setup).
Before this patch for mlx5, XDP redirected frames were returned via
the page allocator. The single flow performance was 6Mpps, and if I
started two flows the collective performance drop to 4Mpps, because we
hit the page allocator lock (further negative scaling occurs).
Two test scenarios need to be covered, for xdp_return_frame API, which
is DMA-TX completion running on same-CPU or cross-CPU free/return.
Results were same-CPU=10Mpps, and cross-CPU=12Mpps. This is very
close to our 13Mpps max target.
The reason max target isn't reached in cross-CPU test, is likely due
to RX-ring DMA unmap/map overhead (which doesn't occur in ixgbe to
ixgbe testing). It is also planned to remove this unnecessary DMA
unmap in a later patchset
V2: Adjustments requested by Tariq
- Changed page_pool_create return codes not return NULL, only
ERR_PTR, as this simplifies err handling in drivers.
- Save a branch in mlx5e_page_release
- Correct page_pool size calc for MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ
V5: Updated patch desc
V8: Adjust for b0cedc844c ("net/mlx5e: Remove rq_headroom field from params")
V9:
- Adjust for 121e892754 ("net/mlx5e: Refactor RQ XDP_TX indication")
- Adjust for 73281b78a3 ("net/mlx5e: Derive Striding RQ size from MTU")
- Correct handling if page_pool_create fail for MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ
V10: Req from Tariq
- Change pool_size calc for MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need a fast page recycle mechanism for ndo_xdp_xmit API for returning
pages on DMA-TX completion time, which have good cross CPU
performance, given DMA-TX completion time can happen on a remote CPU.
Refurbish my page_pool code, that was presented[1] at MM-summit 2016.
Adapted page_pool code to not depend the page allocator and
integration into struct page. The DMA mapping feature is kept,
even-though it will not be activated/used in this patchset.
[1] http://people.netfilter.org/hawk/presentations/MM-summit2016/generic_page_pool_mm_summit2016.pdf
V2: Adjustments requested by Tariq
- Changed page_pool_create return codes, don't return NULL, only
ERR_PTR, as this simplifies err handling in drivers.
V4: many small improvements and cleanups
- Add DOC comment section, that can be used by kernel-doc
- Improve fallback mode, to work better with refcnt based recycling
e.g. remove a WARN as pointed out by Tariq
e.g. quicker fallback if ptr_ring is empty.
V5: Fixed SPDX license as pointed out by Alexei
V6: Adjustments requested by Eric Dumazet
- Adjust ____cacheline_aligned_in_smp usage/placement
- Move rcu_head in struct page_pool
- Free pages quicker on destroy, minimize resources delayed an RCU period
- Remove code for forward/backward compat ABI interface
V8: Issues found by kbuild test robot
- Address sparse should be static warnings
- Only compile+link when a driver use/select page_pool,
mlx5 selects CONFIG_PAGE_POOL, although its first used in two patches
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the IDA infrastructure for getting a cyclic increasing ID number,
that is used for keeping track of each registered allocator per
RX-queue xdp_rxq_info. Instead of using the IDR infrastructure, which
uses a radix tree, use a dynamic rhashtable, for creating ID to
pointer lookup table, because this is faster.
The problem that is being solved here is that, the xdp_rxq_info
pointer (stored in xdp_buff) cannot be used directly, as the
guaranteed lifetime is too short. The info is needed on a
(potentially) remote CPU during DMA-TX completion time . In an
xdp_frame the xdp_mem_info is stored, when it got converted from an
xdp_buff, which is sufficient for the simple page refcnt based recycle
schemes.
For more advanced allocators there is a need to store a pointer to the
registered allocator. Thus, there is a need to guard the lifetime or
validity of the allocator pointer, which is done through this
rhashtable ID map to pointer. The removal and validity of of the
allocator and helper struct xdp_mem_allocator is guarded by RCU. The
allocator will be created by the driver, and registered with
xdp_rxq_info_reg_mem_model().
It is up-to debate who is responsible for freeing the allocator
pointer or invoking the allocator destructor function. In any case,
this must happen via RCU freeing.
Use the IDA infrastructure for getting a cyclic increasing ID number,
that is used for keeping track of each registered allocator per
RX-queue xdp_rxq_info.
V4: Per req of Jason Wang
- Use xdp_rxq_info_reg_mem_model() in all drivers implementing
XDP_REDIRECT, even-though it's not strictly necessary when
allocator==NULL for type MEM_TYPE_PAGE_SHARED (given it's zero).
V6: Per req of Alex Duyck
- Introduce rhashtable_lookup() call in later patch
V8: Address sparse should be static warnings (from kbuild test robot)
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now all the users of ndo_xdp_xmit have been converted to use xdp_return_frame.
This enable a different memory model, thus activating another code path
in the xdp_return_frame API.
V2: Fixed issues pointed out by Tariq.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also convert driver i40e, which very recently got XDP_REDIRECT support
in commit d9314c474d ("i40e: add support for XDP_REDIRECT").
V7: This patch got added in V7 of this patchset.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The virtio_net driver assumes XDP frames are always released based on
page refcnt (via put_page). Thus, is only queues the XDP data pointer
address and uses virt_to_head_page() to retrieve struct page.
Use the XDP return API to get away from such assumptions. Instead
queue an xdp_frame, which allow us to use the xdp_return_frame API,
when releasing the frame.
V8: Avoid endianness issues (found by kbuild test robot)
V9: Change __virtnet_xdp_xmit from bool to int return value (found by Dan Carpenter)
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tuntap driver invented it's own driver specific way of queuing
XDP packets, by storing the xdp_buff information in the top of
the XDP frame data.
Convert it over to use the more generic xdp_frame structure. The
main problem with the in-driver method is that the xdp_rxq_info pointer
cannot be trused/used when dequeueing the frame.
V3: Remove check based on feedback from Jason
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend struct ixgbe_tx_buffer to store the xdp_mem_info.
Notice that this could be optimized further by putting this into
a union in the struct ixgbe_tx_buffer, but this patchset
works towards removing this again. Thus, this is not done.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements basic XDP redirect support in mlx5 driver.
Notice that the ndo_xdp_xmit() is NOT implemented, because that API
need some changes that this patchset is working towards.
The main purpose of this patch is have different drivers doing
XDP_REDIRECT to show how different memory models behave in a cross
driver world.
Update(pre-RFCv2 Tariq): Need to DMA unmap page before xdp_do_redirect,
as the return API does not exist yet to to keep this mapped.
Update(pre-RFCv3 Saeed): Don't mix XDP_TX and XDP_REDIRECT flushing,
introduce xdpsq.db.redirect_flush boolian.
V9: Adjust for commit 121e892754 ("net/mlx5e: Refactor RQ XDP_TX indication")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added red_drops stats. Inbound packets dropped by RED, buffer exhaustion
2. Included fcs_err, jabber_err, l2_err and frame_err errors under
rx_errors
3. Included fifo_err, dmac_drop, red_drops, fw_err_pko, fw_err_link and
fw_err_drop under rx_dropped
4. Included max_collision_fail, max_deferral_fail, total_collisions,
fw_err_pko, fw_err_link, fw_err_drop and fw_err_pki under tx_dropped
5. Counting dma mapping errors
6. Added some firmware stats description and removed for some
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Acked-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace magic number "0x5 << MAX_READ_REQUEST_SHIFT" with the
appropriate constant as defined in PCI core.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch stmmac_mode_ops to generic Hardware Interface Helpers instead of
using hard-coded callbacks. This makes the code more readable and more
flexible.
No functional change.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch stmmac_hwtimestamp to generic Hardware Interface Helpers instead
of using hard-coded callbacks. This makes the code more readable and
more flexible.
No functional change.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch stmmac_ops to generic Hardware Interface Helpers instead of using
hard-coded callbacks. This makes the code more readable and more
flexible.
No functional change.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch stmmac_dma_ops to generic Hardware Interface Helpers instead of
using hard-coded callbacks. This makes the code more readable and more
flexible.
No functional change.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch stmmac_desc_ops to generic Hardware Interface Helpers instead of
using hard-coded callbacks. This makes the code more readable and more
flexible.
No functional change.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface is down, head/tail of the descriptor
ring address is set to 0 in netsec_netdev_stop().
But netsec hardware still keeps the previous descriptor
ring address, so there is inconsistency between driver
and hardware after interface is up at a later time.
To address this inconsistency, add netsec_reset_hardware()
when the interface is down.
In addition, to minimize the reset process,
add flag to decide whether driver loads the netsec microcode.
Even if driver resets the netsec hardware, netsec microcode
keeps resident on RAM, so it is ok we only load the microcode
at initialization.
This patch is critical for installation over network.
Signed-off-by: Masahisa KOJIMA <masahisa.kojima@linaro.org>
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable TX-irq as well during ndo_open() as we can not count upon
RX to arrive early enough to trigger the napi. This patch is critical
for installation over network.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call mtk_probe() is to match an entry in
of_mtk_match[], so match cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a firmware bug, the hypervisor can send an interrupt to a
transmit or receive queue just prior to a partition migration, not
allowing the device enough time to handle it and send an EOI. When
the partition migrates, the interrupt is lost but an "EOI-pending"
flag for the interrupt line is still set in firmware. No further
interrupts will be sent until that flag is cleared, effectively
freezing that queue. To workaround this, the driver will disable the
hardware interrupt and send an H_EOI signal prior to re-enabling it.
This will flush the pending EOI and allow the driver to continue
operation.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell's PPv2 controller has a Packet Header parser, which uses a
fixed-size TCAM array of filter entries.
The mvpp2 driver reserves some ranges among the 256 TCAM entries to
perform MAC and VID filtering. The rest of the TCAM ids are freely usable
for other features, such as IPv4 proto matching.
This commit fixes the MVPP2_PE_LAST_FREE_TID define that sets the end of
the "free range", which included the MAC range. This could therefore allow
some other features to use entries dedicated to MAC filtering,
lowering the number of unicast/multicast addresses that could be allowed
before switching to promiscuous mode.
Fixes: 10fea26ce2 ("net: mvpp2: Add support for unicast filtering")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is just wrong, sorry. I was trying to fix a static checker
warning and misread the code. The reference taken in macsec_newlink()
is released in macsec_free_netdev() when the netdevice is destroyed.
This reverts commit 5dcd840088.
Reported-by: Laura Abbott <labbott@redhat.com>
Fixes: 5dcd840088 ("macsec: missing dev_put() on error in macsec_newlink()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A misconfigured system (e.g. with all interrupts affinitised to all CPUs)
may produce a storm of ARFS steering events. With the existing sfc ARFS
implementation, that could create a backlog of workitems that grinds the
system to a halt. To prevent this, limit the number of workitems that
may be in flight for a given SFC device to 8 (EFX_RPS_MAX_IN_FLIGHT), and
return EBUSY from our ndo_rx_flow_steer method if the limit is reached.
Given this limit, also store the workitems in an array of slots within the
struct efx_nic, rather than dynamically allocating for each request.
The limit should not negatively impact performance, because it is only
likely to be hit in cases where ARFS will be ineffective anyway.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we inserted an ARFS filter for ndo_rx_flow_steer(), we didn't know
what the filter ID would be, so we just returned 0. Thus, we must also
pass 0 as the filter ID when calling rps_may_expire_flow() for it, and
rely on the flow_id to identify what we're talking about.
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Necessary to allow redirecting a flow when the application moves.
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We tends to batch submitting packets during XDP_TX. This requires to
kick virtqueue after a batch, we tried to do it through
xdp_do_flush_map() which only makes sense for devmap not XDP_TX. So
explicitly kick the virtqueue in this case.
Reported-by: Kimitoshi Takahashi <ktaka@nii.ac.jp>
Tested-by: Kimitoshi Takahashi <ktaka@nii.ac.jp>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Fixes: 186b3c998c ("virtio-net: support XDP_REDIRECT")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA stack passes received PTP frames to this driver via
mv88e6xxx_port_rxtstamp() for deferred delivery. The driver then
queues the frame and kicks the worker thread. The work callback reads
out the latched receive time stamp and then works through the queue,
delivering any non-matching frames without a time stamp.
If a new frame arrives after the worker thread has read out the time
stamp register but enters the queue before the worker finishes
processing the queue, that frame will be delivered without a time
stamp.
This patch fixes the race by moving the queue onto a list on the stack
before reading out the latched time stamp value.
Fixes: c6fe0ad2c3 ("net: dsa: mv88e6xxx: add rx/tx timestamping support")
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a second skb list for handling control messages and limit the
number of allowed messages. Some control messages are considered more
crucial than others, resulting in the need for a second skb list. By
splitting the list into a separate high and low priority list we can
ensure that messages on the high list get added to the head of the list
that gets processed, this however has no functional impact. Previously
there was no limit on the number of messages allowed on the queue, this
could result in the queue growing boundlessly and eventually the host
running out of memory.
Fixes: b985f870a5 ("nfp: process control messages in workqueue in flower app")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we processed the route ack control messages in the workqueue,
this unnecessarily loads the workqueue. We can deal with these messages
sooner as we know we are going to drop them.
Fixes: 8e6a9046b6 ("nfp: flower vxlan neighbour offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When waiting for an NFP mutex is interrupted print a message
to make root causing later error messages easier.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently allow signals to interrupt the wait for management FW
commands. Exiting the wait should not cause trouble, the FW will
just finish executing the command in the background and new commands
will wait for the old one to finish.
However, this may not be what users expect (Ctrl-C not actually stopping
the command). Moreover some systems routinely request link information
with signals pending (Ubuntu 14.04 runs a landscape-sysinfo python tool
from MOTD) worrying users with errors like these:
nfp 0000:04:00.0: nfp_nsp: Error -512 waiting for code 0x0007 to start
nfp 0000:04:00.0: nfp: reading port table failed -512
Make the wait for management FW responses non-interruptible.
Fixes: 1a64821c6a ("nfp: add support for service processor access")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attempting to change the driver parameters, such as the MTU
value or number of queues, do not call netdev_notify_peers().
Doing so will deadlock on the rtnl_lock.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug in handling the possible return codes from sending the
login CRQ. The current code treats any non-success return value,
minus failure to send the crq and a timeout waiting for a login response,
as a need to re-send the login CRQ. This can put the drive in an
infinite loop of trying to login when getting return values other
that a partial success such as a return code of aborted. For these
scenarios the login will not ever succeed at this point and the
driver would need to be reset again.
To resolve this loop trying to login is updated to only retry the
login if the driver gets a return code of a partial success. Other
return codes are treated as an error and the driver returns an error
from ibmvnic_login().
To avoid infinite looping in the partial success return cases, the
number of retries is capped at the maximum number of supported
queues. This value was chosen because the driver does a renegotiation
of capabilities which sets the number of queues possible and allows
the driver to attempt a login for possible value for the number
of queues supported.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch is to configure DSP registers of PHY device
to handle Gbe-EEE failures with >40m cable length.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "name" field of struct vnic_login_client_data is a char array of
undefined length. This should be written as "char name[]" so the compiler
can make better decisions about the field (for example, not assuming
it's a single character). This was noticed while trying to tighten the
CONFIG_FORTIFY_SOURCE checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) In ip_gre tunnel, handle the conflict between TUNNEL_{SEQ,CSUM} and
GSO/LLTX properly. From Sabrina Dubroca.
2) Stop properly on error in lan78xx_read_otp(), from Phil Elwell.
3) Don't uncompress in slip before rstate is initialized, from Tejaswi
Tanikella.
4) When using 1.x firmware on aquantia, issue a deinit before we
hardware reset the chip, otherwise we break dirty wake WOL. From
Igor Russkikh.
5) Correct log check in vhost_vq_access_ok(), from Stefan Hajnoczi.
6) Fix ethtool -x crashes in bnxt_en, from Michael Chan.
7) Fix races in l2tp tunnel creation and duplicate tunnel detection,
from Guillaume Nault.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
l2tp: fix race in duplicate tunnel detection
l2tp: fix races in tunnel creation
tun: send netlink notification when the device is modified
tun: set the flags before registering the netdevice
lan78xx: Don't reset the interface on open
bnxt_en: Fix NULL pointer dereference at bnxt_free_irq().
bnxt_en: Need to include RDMA rings in bnxt_check_rings().
bnxt_en: Support max-mtu with VF-reps
bnxt_en: Ignore src port field in decap filter nodes
bnxt_en: do not allow wildcard matches for L2 flows
bnxt_en: Fix ethtool -x crash when device is down.
vhost: return bool from *_access_ok() functions
vhost: fix vhost_vq_access_ok() log check
vhost: Fix vhost_copy_to_user()
net: aquantia: oops when shutdown on already stopped device
net: aquantia: Regression on reset with 1.x firmware
cdc_ether: flag the Cinterion AHS8 modem by gemalto as WWAN
slip: Check if rstate is initialized before uncompressing
lan78xx: Avoid spurious kevent 4 "error"
lan78xx: Correctly indicate invalid OTP
...
- Rework the idle loop in order to prevent CPUs from spending too
much time in shallow idle states by making it stop the scheduler
tick before putting the CPU into an idle state only if the idle
duration predicted by the idle governor is long enough. That
required the code to be reordered to invoke the idle governor
before stopping the tick, among other things (Rafael Wysocki,
Frederic Weisbecker, Arnd Bergmann).
- Add the missing description of the residency sysfs attribute to
the cpuidle documentation (Prashanth Prakash).
- Finalize the cpufreq cleanup moving frequency table validation
from drivers to the core (Viresh Kumar).
- Fix a clock leak regression in the armada-37xx cpufreq driver
(Gregory Clement).
- Fix the initialization of the CPU performance data structures
for shared policies in the CPPC cpufreq driver (Shunyong Yang).
- Clean up the ti-cpufreq, intel_pstate and CPPC cpufreq drivers
a bit (Viresh Kumar, Rafael Wysocki).
- Mark the expected switch fall-throughs in the PM QoS core (Gustavo
Silva).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Pnk4
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These include one big-ticket item which is the rework of the idle loop
in order to prevent CPUs from spending too much time in shallow idle
states. It reduces idle power on some systems by 10% or more and may
improve performance of workloads in which the idle loop overhead
matters. This has been in the works for several weeks and it has been
tested and reviewed quite thoroughly.
Also included are changes that finalize the cpufreq cleanup moving
frequency table validation from drivers to the core, a few fixes and
cleanups of cpufreq drivers, a cpuidle documentation update and a PM
QoS core update to mark the expected switch fall-throughs in it.
Specifics:
- Rework the idle loop in order to prevent CPUs from spending too
much time in shallow idle states by making it stop the scheduler
tick before putting the CPU into an idle state only if the idle
duration predicted by the idle governor is long enough.
That required the code to be reordered to invoke the idle governor
before stopping the tick, among other things (Rafael Wysocki,
Frederic Weisbecker, Arnd Bergmann).
- Add the missing description of the residency sysfs attribute to the
cpuidle documentation (Prashanth Prakash).
- Finalize the cpufreq cleanup moving frequency table validation from
drivers to the core (Viresh Kumar).
- Fix a clock leak regression in the armada-37xx cpufreq driver
(Gregory Clement).
- Fix the initialization of the CPU performance data structures for
shared policies in the CPPC cpufreq driver (Shunyong Yang).
- Clean up the ti-cpufreq, intel_pstate and CPPC cpufreq drivers a
bit (Viresh Kumar, Rafael Wysocki).
- Mark the expected switch fall-throughs in the PM QoS core (Gustavo
Silva)"
* tag 'pm-4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
tick-sched: avoid a maybe-uninitialized warning
cpufreq: Drop cpufreq_table_validate_and_show()
cpufreq: SCMI: Don't validate the frequency table twice
cpufreq: CPPC: Initialize shared perf capabilities of CPUs
cpufreq: armada-37xx: Fix clock leak
cpufreq: CPPC: Don't set transition_latency
cpufreq: ti-cpufreq: Use builtin_platform_driver()
cpufreq: intel_pstate: Do not include debugfs.h
PM / QoS: mark expected switch fall-throughs
cpuidle: Add definition of residency to sysfs documentation
time: hrtimer: Use timerqueue_iterate_next() to get to the next timer
nohz: Avoid duplication of code related to got_idle_tick
nohz: Gather tick_sched booleans under a common flag field
cpuidle: menu: Avoid selecting shallow states with stopped tick
cpuidle: menu: Refine idle state selection for running tick
sched: idle: Select idle state before stopping the tick
time: hrtimer: Introduce hrtimer_next_event_without()
time: tick-sched: Split tick_nohz_stop_sched_tick()
cpuidle: Return nohz hint from cpuidle_select()
jiffies: Introduce USER_TICK_USEC and redefine TICK_USEC
...
I added dumping of link information about tun devices over netlink in
commit 1ec010e705 ("tun: export flags, uid, gid, queue information
over netlink"), but didn't add the missing netlink notifications when
the device's exported properties change.
This patch adds notifications when owner/group or flags are modified,
when queues are attached/detached, and when a tun fd is closed.
Reported-by: Thomas Haller <thaller@redhat.com>
Fixes: 1ec010e705 ("tun: export flags, uid, gid, queue information over netlink")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, register_netdevice advertises the creation of the device with
the default flags, instead of what the user requested.
Reported-by: Thomas Haller <thaller@redhat.com>
Fixes: 1ec010e705 ("tun: export flags, uid, gid, queue information over netlink")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 92571a1aae ("lan78xx: Connect phy early") moves the PHY
initialisation into lan78xx_probe, but lan78xx_open subsequently calls
lan78xx_reset. As well as forcing a second round of link negotiation,
this reset frequently prevents the phy interrupt from being generated
(even though the link is up), rendering the interface unusable.
Fix this issue by removing the lan78xx_reset call from lan78xx_open.
Fixes: 92571a1aae ("lan78xx: Connect phy early")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When open fails during ethtool -L ring change, for example, the driver
may crash at bnxt_free_irq() because bp->bnapi is NULL.
If we fail to allocate all the new rings, bnxt_open_nic() will free
all the memory including bp->bnapi. Subsequent call to bnxt_close_nic()
will try to dereference bp->bnapi in bnxt_free_irq().
Fix it by checking for !bp->bnapi in bnxt_free_irq().
Fixes: e5811b8c09 ("bnxt_en: Add IRQ remapping logic.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent changes to reserve both L2 and RDMA rings, we need to include
the RDMA rings in bnxt_check_rings(). Otherwise we will under-estimate
the rings we need during ethtool -L and may lead to failure.
Fixes: fbcfc8e467 ("bnxt_en: Reserve completion rings and MSIX for bnxt_re RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While a VF is configured with a bigger mtu (> 1500), any packets that
are punted to the VF-rep (slow-path) get dropped by OVS kernel-datapath
with the following message: "dropped over-mtu packet". Fix this by
returning the max-mtu value for a VF-rep derived from its corresponding VF.
VF-rep's mtu can be changed using 'ip' command as shown in this example:
$ ip link set bnxt0_pf0vf0 mtu 9000
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently uses src port field (along with other fields) in the
decap tunnel key, while looking up and adding tunnel nodes. This leads to
redundant cfa_decap_filter_alloc() requests to the FW and flow-miss in the
flow engine. Fix this by ignoring the src port field in decap tunnel nodes.
Fixes: f484f6782e ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch the following commands would succeed as far as the
user was concerned:
$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol all \
flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:01/44 action drop
The current flow offload infrastructure used does not support wildcard
matching for ethernet headers, so do not allow the second or third
commands to succeed. If a user wants to drop traffic on that interface
the protocol and MAC addresses need to be specified explicitly:
$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol arp \
flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw action drop
...
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:01 action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:02 action drop
...
There are also checks for VLAN parameters in this patch as other callers
may wildcard those parameters even if tc does not. Using different
flow infrastructure could allow this to work in the future for L2 flows,
but for now it does not.
Fixes: 2ae7408fed ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ethtool .get_rxfh() crash by checking for valid indirection table
address before copying the data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preferred to opencoding an IDA_INIT.
Link: http://lkml.kernel.org/r/20180313132639.17387-2-willy@infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case netdev is closed at the moment of pci shutdown, aq_nic_stop
gets called second time. napi_disable in that case hangs indefinitely.
In other case, if device was never opened at all, we get oops because
of null pointer access.
We should invoke aq_nic_stop conditionally, only if device is running
at the moment of shutdown.
Reported-by: David Arcari <darcari@redhat.com>
Fixes: 90869ddfef ("net: aquantia: Implement pci shutdown callback")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
