Refactor VF RSS code to allow RSS on a single queue and eliminate
the need for the next_queue function.
Change-ID: I9253bad96b7f542ee7036e15636db0e5d58d8ef2
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC filter list is protected by a critical task bit, and the VLAN
list should be protected as well. This prevents list corruption if the
watchdog happens to run at the same time as a VLAN filter is being added
or deleted.
Change-ID: Ia4867cebbbb046a1f38012771b288a634ca5882b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call the netdev carrier off and TX disable functions first, before other
shutdown operations. This stops the stack from hitting us with
transmits while we're shutting down. Additionally, disable NAPI before
disabling interrupts, or the interrupt might get re-enabled
inappropriately. Finally, remove the call to netif_tx_stop_all_queues,
as it is redundant - the call to netif_tx_disable already did the same
thing.
Change-ID: I8b2dd25231b82817746cc256234a5eeeb4abaccc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VF interface is closed, we cannot immediately free our rings
and RX buffers, because the hardware hasn't yet stopped accessing this
memory. This shows up as a panic or memory corruption when the device is
brought down while under heavy stress.
To fix this, delay releasing resources until we receive acknowledgment
from the PF driver that the rings have indeed been stopped. Because of
this delay, we also need to check to make sure that all of our admin
queue requests have been handled before allowing the device to be
opened.
Change-ID: I44edd35529ce2fa2a9512437a3a8e6f14ed8ed63
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump PF version to 1.2.37 and VF version to 1.2.25
Change-ID: I0287a750408250dc055c03e1f744fd5f0caefd68
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug introduced in the force writeback code, where the interrupt
rate was set to 0 (maximum) by accident.
The driver must correctly set the NOITR fields to avoid ITR update
as a side effect of triggering the software interrupt.
Change-ID: I290851ae04ef3811c43aab5ee33242029f26c1a3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset occurs when the netdev is closed, the reset task will hang in
napi_disable, causing deadlocks and general grumpiness.
Check to make sure the device is actually running before stopping
everything. This allows the reset task to complete and have a real good
time.
Change-ID: Iaaea84acbcb9b3810c216b14c3326e4287b75b58
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.12 and i40evf to 1.2.6.
Change-ID: I641871da3a9abd396b28eda5744a4d68493c1400
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.11 and i40evf to 1.2.5
Change-ID: Ie13375941606b0a027e5b5dbc235f5f5f03b75c8
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.10 and i40evf to 1.2.4
Change-ID: I48aa64df05fcc8356e7026f3a9e69ecf78d0c785
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.9 and i40evf 1.2.3
Also update the copyright year.
Change-ID: I345d777e94abd0acffe6a28793f675d251a86299
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the netdev name to the VF misc vector name. Without
this patch, all the interrupts show the same info, so it difficult to
distinguish them.
Change-ID: I247828697e1373ecfb5f8dc1bc9618e98a7f4942
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Under rare circumstances, after a reset, set_rx_mode might get called
while the watchdog is running, which will cause a deadlock on the
critical section lock. To correct this, add a counter and give up trying
to get the lock after fifty tries. Log a message if this happens but
don't take any other action. Because this happens after a reset, all of
the Rx filters are still in place and the device won't lose
connectivity.
We can also get stuck during shutdown, if the PF has stopped communicating
with us, or if a reset is occurring. If we can't get the lock after a reasonable
amount of time, just error out. Something else bad is happening anyway, so
adding this filter is the least of our concern right now.
Change-ID: I159731e2a82a06b389ee31b34ce336548e05baa0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change to the shutdown flow messed up the reset flow. Since
i40evf_down now holds the critical section lock, we cannot call it from
the reset handler, which also holds the lock. To do so causes a deadlock
accompanied by wailing and gnashing of teeth. This is easily triggered
by running an ethtool self-test on the PF device.
Instead, we move the relevant portions of i40evf_down into the reset
handler and bend them to our will. Additionally, we can optimize the
reinit path by not deleting the MAC and VLAN filters and then adding
them back again. Instead, we just set the 'add' flag and let the
watchdog resynchronize the filter list with the PF driver. We also
reword a few messages to make them more consistent with the rest of the
driver.
Change-ID: I03dd92ae736f7719fca3564b12a2cf9b98c6cb18
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When closing the interface, disable NAPI polling before any other
activities. This fixes an occasional panic during close caused by the
driver trying to delete and clean rings at the same time.
Change-ID: Ib4d427b13d310258ea85b248d535da70ecf0c1e9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.8 and i40evf to 1.2.2
Change-ID: I64f47c3367ea8ff2a53068e895d7a1f60726c871
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the receive hot path code into two, one for packet split and one
for single buffer. This improves receive performance since we only need
to check if the ring is in packet split mode once per NAPI poll time,
not several times per packet. The single buffer code is further improved
by the removal of a bunch of code and several variables that are not
needed. On a receive-oriented test this can improve single-threaded
throughput.
Also refactor the packet split receive path to use a fixed buffer for
headers, like ixgbe does. This vastly reduces the number of DMA mappings
and unmappings we need to do, allowing for much better performance in
the presence of an IOMMU.
Lastly, correct packet split descriptor types now that we are actually
using them.
Change-ID: I3a194a93af3d2c31e77ff17644ac7376da6f3e4b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop the watchdog during shutdown. Failing to do this causes a log full
of admin queue errors and the occasional hang when the system is shut
down.
Change-ID: Ib2fd11213cca2fa589eb68577e86b1000c23c250
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Occasionally on shutdown, the FW will hand us a bunch of messages filled
with zeros, which can cause us to spin trying to handle them. Just
ignore these and get on with shutting down.
Change-ID: I347e9648f7153ad5a7b7e0847b87f7aad5f3e0da
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the module is being unloaded, don't wait for the PF to politely
handle all of our admin queue requests, as that might take forever with
a lot of VFs enabled. Instead, just stop everything and request a VF
reset.
When the original shutdown code was written, VF resets were unreliable,
so we avoided them. But with production hardware and firmware, and the
1.x PF driver, this is no longer the case.
This fixes a potential multi-minute delay on driver unload, VF disable,
or system shutdown.
Change-ID: Ib43d6d860ef6b9b8f26e8dce0615a0302608c7d9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.6 and i40evf to 1.2.0 version.
Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.5 and i40evf to 1.0.7.
Change-ID: I622556829056e3ed42d3b9d285fc5ffb693b21cc
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some versions of the firmware, the VF admin send queue may become
stalled. In this case, the easiest solution is to just place another
descriptor on the queue; the firmware will then process both requests.
The early init code already accounts for this, but the runtime code does
not. In the watchdog task, check for the stall condition, and if it's
found, send our API version to the PF. When the PF replies, just ignore
the reply.
Change-ID: I380d78185a4f284d649c44d263e648afc9b4d50c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't enable vector 0 in the ISR, just schedule the adminq task and let
it enable the vector. This prevents the task from being called
reentrantly. Make sure that the vector is enabled on all exit paths of
the adminq task, including error exits.
Change-ID: I53f3d14f91ed7a9e90291ea41c681122a5eca5b5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is always a possibility that MSI-X interrupts can get lost. To
keep this problem from stalling the driver, we fire all of our MSI-X
vectors during the watchdog routine. However, we should not fire the
traffic vectors when the interface is closed. In this case, just fire
vector 0, which is used for admin queue events.
As a result, we do not enable the interrupt cause for vector 0. This
can cause the admin queue handler to be called reentrantly, which
causes a scary "critical section violation" message to be logged,
even though no real damage is done.
Change-ID: Ic43a5184708ab2cb9a23fca7dedd808a46717795
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we're using VLANs and communications with the PF fail during
shutdown, we will leak memory because not all of the VLAN filters will
be removed. To eliminate this possibility, go through the list again
right before the module is removed and delete any leftover entries.
Change-ID: Id3b5315c47ca0a61ae123a96ff345d010bc41aed
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF driver is running in the host, the shutdown code is completely
broken. We cannot wait in our down routine for the PF to respond to our
requests, as its admin queue task will never run while we hold the lock.
Instead, we schedule operations, then let the watchdog take care of
shutting things down. If the driver is being removed, then wait in the
remove routine until the watchdog is done before continuing.
Change-ID: I93a58d17389e8d6b58f21e430b56ed7b4590b2c5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These messages may be triggered during normal init of the driver if the
PF or FW take a long time to respond. There's nothing really wrong, so
don't freak people out logging messages.
If the communication channel really is dead, then we'll retry a few
times and give up. This will log a different more scary message that
should cause consternation. This allows the user to more easily detect a
genuine failure.
Change-ID: I6e2b758d4234a3a09c1015c82c8f2442a697cbdb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions are redundant and duplicate functionality found in
i40evf_free_all_[tx|rx]_resources.
Change-ID: Ia199908926d7a1a4b8247f75f89b5da24c9b149c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When multiple VFs attempt to initialize simultaneously, the firmware may
delay or drop messages. Make the init code more adept at handling these
situations by a) reinitializing the admin queue if the firmware fails to
process a request, and b) resending a request if the PF doesn't answer.
Once the request has been sent again, the PF might end up getting both
requests and send the configuration information to the driver twice.
This will cause the VF to complain about receiving an unexpected message
from the PF. Since this is not fatal, reduce the warning level of the
log messages that are generated in response to this event.
Change-ID: I9370a1a2fde2ad3934fa25ccfd0545edfbbb4805
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the if part of this statement contains a break, there's no reason
for the else. Clean up the code and make it more obvious that the delay
happens each time through the loop.
Change-ID: I9292eaf7dd687688bdc401b8bd8d1d14f6944460
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most of the null-checking in this driver is of the style if (!foo),
except these few. Make these checks consistent with the rest of the
code.
Change-ID: I991924f34072fa607a1b626a8b3f1fa5195d43e9
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is the result of running checkpatch on the i40evf driver with
the --strict option. The vast majority of changes are adding/removing
blank lines, aligning function parameters, and correcting over-long
lines.
The only possible functional change is changing the flags member of the
adapter structure to be non-volatile. However, according to the kernel
documentation, this is not necessary and the volatile should be removed.
Change-ID: Ie8c6414800924f529bef831e8845292b970fe2ed
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Overloading the msg_size field in the arq_event_info struct is just a
bad idea. It leads to repeated bugs when the structure is used in a
loop, since the input value (buffer size) is overwritten by the output
value (actual message length).
Fix this by splitting the field into two and renaming to indicate the
actual function of each field.
Since the arq_event struct has now changed, we need to change the drivers
to support this. Note that we no longer need to initialize the buffer size
each time we go through a loop as this value is no longer destroyed by
arq processing.
In the process, we also fix a bug in i40evf_verify_api_ver where the
buffer size was not correctly reinitialized each time through the loop.
Change-ID: Ic7f9633cdd6f871f93e698dfb095e29c696f5581
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's kind of silly to configure and attempt to use a bunch of queue
pairs when you're running on a single (virtual) CPU. Instead of
unconditionally configuring all of the queues that the PF gives us,
clamp the number of queue pairs to the number of CPUs.
Change-ID: I321714c9e15072ee76de8f95ab9a81f86ed347d1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we receive an admin queue message, the msg_size field in the event
struct gets overwritten. Because of this, we need to reinit the field
each time we go through the loop. Without this we may receive truncated
messages due to the firmware thinking we have insufficient buffer size.
Change-ID: I21dcca5114d91365d731169965ce3ffec0e4a190
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the Documentation/timers/timers-howto.txt it is preferred to use
usleep_range() instead of udelay() if the delay value is > 10us in
non-atomic contexts.
So, replacing all the instances of udelay() with 10 or greater than 10
micro seconds delay in the driver and using usleep_range() instead.
Change-ID: Iaa2ab499a4c26f6005e5d86cc421407ef9de16c7
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e version to 1.0.11 and i40evf version to 1.0.5.
Change-ID: I63a60fa2efe82aae87a8a3095f43218db57d46ce
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Bump versions for i40e to 1.0.4 and i40evf to 1.0.1.
Change-ID: I960c04da2c91bdf1d02f8e5011e68c34a634122d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Removing VF driver during device still in reset caused guest OS panic.
in the i40evf_remove(), we're trying to clean mac_filter_list which has
not been initialized since the device is still stuck at the reset.
The change is to initialize the filter_list before setting any task.
Change-ID: I8b59df7384416c7e6f2d264b598f447e1c2c92b0
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is loaded and then unloaded before the interface is
brought up, then it will allocate a MAC filter entry and never free it.
To fix this, on unload, run through the mac filter list and free all the
entries. We also do this during reset recovery when the driver cannot
contact the PF and needs to shut down completely.
Change-ID: I15fabd67eb4a1bfc57605a7db60d0b5d819839db
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak. Driver was allocating memory for queue vectors on
init but not freeing them on shutdown. These need to be freed at two
different times: during module unload, and during reset recovery when
the driver cannot contact the PF driver and needs to give up.
Change-ID: I7c1d0157a776e960d4da432dfe309035aad7c670
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in an adapter state check to prevent re-arming watchdog timer after
i40evf_remove has been called and timer has been deleted.
Change-ID: I636ba7c6322be8cbf053231959f90c0a2d8d803a
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously defined state I40E_VFR_VFACTIVE uses bit 1 which is now set to
"reserved." Update the state checks to also include I40E_VFR_COMPLETED.
This change will allow the VF to work with both existing and future PFs.
Change-ID: Ifd1d34f79f3b0ffd6d2550ee4dadc55825ff52f8
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was converted to use snprintf everywhere but this one function.
Just use snprintf, instead of sprintf.
Also a small spelling correction in a comment.
Change-ID: I59d45f94a52754c7b4cd6034df9a61d8132b7f77
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We really don't need to delay an entire millisecond just to get into our
critical section. A microsecond will be sufficient, thank you.
Change-ID: I2d02ece6610007d98cabcb3f42df9a774bb54e59
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump.
Change-ID: Ie0c36583ffd9997679f46bdf89bc462d3e992995
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40evf_irq_enable and i40evf_fire_sw_interrupt functions were
unfairly discriminating against MSI-X vector 0, just because it doesn't
handle traffic. That doesn't mean it's not essential to the operation of
the driver. This change allows the watchdog to fire vector 0 via
software, which makes the driver tolerant of dropped interrupts on that
vector.
Buck up, vector 0! You can be part of our gang!
Change-ID: I37131d955018a6b3e711e1732d21428acd0d767e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a slash to the branding string to reduce confusion and match up with
our other marketing materials.
Change-ID: I8229e8c3e43083b7a29c859a250f8d2d4dc46b9e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes the firmware will not indicate an error but fail to pass a
message between the VF and the PF driver. If this happens, just resend
the request.
This fixes an initialization failure if many VFs are instantiated at the
same time and the VF module is autoloaded.
Change-ID: Idd1ad8da2fd5137859244685c355941427d317d7
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct a missing word in a log message.
Change-ID: Id94da7d9f842382d073b3947e0b616503e2f8e91
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF driver fails to complete early init, then rmmod can cause a
softlock when the driver tries to stop a watchdog timer that never even
got initialized.
Add a check to see if the timer is actually initialized before stopping
it.
Change-ID: Id9d550aa8838e07f4b02afe7bc017ef983779efc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FW can indicate any admin queue error states to the driver via some bits
in the length registers. Each time we process an admin queue message,
check these bits and log any errors we find. Since the VF really can't
do much, we just print the message and depend on the PF driver to clear
things up on our behalf.
Change-ID: I92bc6c53ce3b4400544e0ca19c5de2d27490bd0d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linux gives us a function to copy Ethernet MAC addresses, let's use it.
Change-ID: I0c861900029ca5ea65a53ca39565852fb633f6fd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the device is down, there's no place to go but up, so don't try to go
down even more. This prevents a CPU soft lock in napi_disable().
Change-ID: I8b058b9ee974dfa01c212fae2597f4f54b333314
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bumpity and Fred Worm say it's time to change the numbers again.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I658731d022ea23cedede4be2bfecd8b4cc68d270
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix function header comment to have the correct function name.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 0.4.5 and i40evf to 0.9.29.
Change-ID: I9faca5544446518c5425612e733499cf16ef20a1
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a coding error where during the registration for NAPI
the driver requested 256 budget. The max recommended
value for this is NAPI_POLL_WEIGHT or 64.
Change-ID: I03ea1e2934a84ff1b5d572988b18315d6d91c5c6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Both the PF side and the VF side of the VF reset process are too noisy.
We already warn the user that a reset is happening, and that is
sufficient.
Because some of these message are inside if statements, we have to
rejigger the brackets at the same time to keep our coding style
consistent.
Change-ID: Id175562fb0ec7c396d9de156b4890e136f52d5f4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The correct format is %pM, not %pMAC.
Change-ID: Idb335723a966fe56db3a72b9c07c08ca66f9db3c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up inconsistent log messages, mostly related to punctuation. Based
on the dogma that "kernel messages are not sentences", remove all
trailing periods. Reword a few of the messages to make them less
sentence-like.
Change-ID: Ibd849aa7623a77549b0709988c66ab05d1311472
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This comment is just plain false. VF drivers require MSI-X or they won't
get interrupts at all.
Change-ID: Iaea5e30b6926948aa834a3c506d9a9223d9e3e29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to print log messages when we encounter an out-of-memory
condition, as the allocator will do this for us. Also, remove a Tx hang
message that duplicates the one emitted by the netdev layer, and a
duplicate message in the watchdog.
Change-ID: If2056e6135fe248f66ea939778f9895660f4d189
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 0.4.3 and i40evf to 0.9.27.
Change-ID: I4141e9f8615bdcfa3b1b5ecbc2ac62603a03b7ad
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Depending on the timing of what the PF driver is doing, it make take a
few tries before the VF driver is able to communicate with the PF driver
on init or reset recovery. In order to prevent confusion, make the most
common messages less scary by lowering them to a less terrifying log
level and indicate that the driver will retry.
Change-ID: I1ec22aa59a68f4469aabe14775a1bfc1ab4b7f2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40evf_set_ringparam was broken in several ways. First, it only changed
the size of the first ring, and second, changing the ring size would
often result in a panic because it would change the count before
deallocating resources, causing the driver to either free nonexistent
buffers, or leak leftover buffers.
Fix this by storing the descriptor count in the adapter structure, and
updating the count for each ring each time we allocate them. This
ensures that we always free the right size ring, and always end up with
the requested count when the device is (re)opened.
Change-ID: I298396cd3d452ba8509d9f2d33a93f25868a9a55
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The RESETTING state means that a Catastrophic Hardware Bad Thing is
happening and the driver need to tiptoe around and not use the admin
queue or registers or anything like that.
On the other hand, a reinit is no big deal and we can use the admin
queue, and we should. So don't set the state to RESETTING here.
This fixes a Tx hang and FW crash that happens after setting the MTU on
a VF.
Change-ID: I3e6191edbd6a93958a1f1bd1d41a5c2d17474d41
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the is_multicast_ether_addr helper function from linux/etherdevice.h
instead of open coding the multicast address check.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove cases where useless bare return is left at end of function.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool consistently reports 0 values for our ITR settings because
we never actually set them. Fix this by setting the default values
to the specified default values.
Change-ID: I2832406a66f7140f2b1230945d6ff6cbf77467c8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding the appropriate GNU General Public License header and
update copyright year to 2014.
Change-ID: I769dd2d37d70350afd0c8727ae2859c0fd340361
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the PF driver fails or is removed from the host, the VF driver will
fill up its log with this message.
Change-ID: I67045f987f7c0d444d21ded403adc509343cdb8f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a panic that would occur in the VF if the PF driver failed or was
removed from the host kernel. In this case, the VF driver calls
i40evf_close(), but this function does nothing because the driver is in
the resetting state. Because of this, the driver doesn't free its irqs
and causes a kernel panic when it tries to disable MSI-X.
Change-ID: If95644a89e554b4d7be0dca1b6add26f63047129
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to version 0.3.43 and i40evf to version 0.9.21.
Change-ID: Ice4c715731bfa1dfc12dd45418675a3ba6e08d57
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change broke the RSS LUT programming, causing it to be
programmed with all 0. Correct this by actually assigning the
incremented value back to the counter variable so that the increment
will be remembered by the calling function.
While we're at it, add a proper kernel-doc function comment to our
helper function.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit 6494294f27 ("i40e/i40evf: Use
dma_set_mask_and_coherent") uses dma_set_mask_and_coherent() to
replace dma_set_coherent_mask() for the benefit of return error.
The conversion brings some confusion in error checking as whether
against DMA_BIT_MASK(64) or DMA_BIT_MASK(32). For one, if error is
zero, the check will be against DMA_BIT_MASK(64) twice. Fix this
error checking by binding the check to the pertinent one.
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx watchdog handler runs in interrupt context, so it would cause an
oops when sending an admin queue message to request a reset, because the
admin queue functions use spinlocks.
Instead, set a flag and let the reset task handle sending the request.
Change-ID: I65879470b72963d9c308edfb8f45ac4fbba2c14f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an error message when the admin queue message never completes, and
fix formatting on another one that was unnecessarily wrapped.
Change-ID: I8b8a4eb7629d741f09357250144023cd4a72231f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver encounters an error while communicating with the PF
driver, don't just shut down the admin queue unconditionally. The PF
may be delayed, and shutting down the admin queue causes it to fail
completely. If this happens, the VF will never complete initialization.
Change-ID: I6192e9d8caeefb738428c3597fa2f54fa400ce7f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump to version 0.3.36 for i40e and 0.9.16 for i40evf.
Change-ID: I7b4ff97b32d2825181803c03c316381a7608a618
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Checkpatch complained in an earlier patch about using min(), but that
change would have been completely unrelated to the point of that patch.
So fix it here.
Change-ID: I2cd87b39cfd406850d283b88f259757a6bcd14cd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HLUT programming loop in in i40evf_configure_rss was a) overly-
complicated, and b) just plain broken. Most of the entries ended up being
not written at all, so most of the flows ended up at queue zero.
Refactor the HLUT programming loop to simply walk through the registers
and write four values to each one, incrementing through the number of
available queues.
Change-ID: I75766179bc67e4e997187794f3144e28c83fd00d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In Linux 3.13, dma_set_mask_and_coherent was introduced, and we have
been encouraged to use it. It simplifies the DMA mapping code a bit as
well.
Change-ID: I66e340245af7d0dedfa8b40fec1f5e352754432e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that the 2.4 firmware reports the correct number of MSI-X vectors,
use this value correctly when communicating with the VF, and when
setting up the interrupt linked list.
The PF has always reported the correct number of MSI-X vectors, so we
should never increment the value in the vf driver.
Change-ID: Ifeefc631c321390192219ce2af9ada6180c1492f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set netdev->hw_features to enable the ndo_set_features netdev op.
Change-Id: I5a086fbfa5a089de5adba2800c4d0b3a73747b11
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix inconsistent use of MSIX and MSI-X in messages.
Change-ID: Iae9ffb42819677c34544719044ed77632e06147d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bunch of changes merit a new version number, and since these were
made in the new year, update the copyright date.
Change-ID: Ic3f282bf0c20679b9fb06860211afa7c78055bc2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the descriptor ring size in the actual ring structs instead of in
the adapter struct. This enables us to use common tx and rx code with
the i40e PF driver.
Also update copyrights.
Change-ID: I2861e599b2b4c76441c062ea14400f4750f54d0e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to set an interface name here; the net core will do
that, and then it will get renamed by udev anyway.
Change-ID: I839a17837d19bedd1f490bff32ac5b85b4bfd97f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This comment is simply not true.
Change-ID: If006b02b60984601a24257a951ae873dff568008
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure errors are reported at the correct log level, quit printing
the function name every time, and make the messages more consistent in
format.
v2: Removed unnecessary periods and redundant OOM message.
Change-ID: I50e443467519ad3850def131d84626c50612c611
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI DAC doesn't really mean much on a virtualized PCI Express part, so
get rid of that check and just always set the HIGHDMA flag in the net
device.
Change-ID: I2040272be0e7934323f470c2bc73fbdd4f93e2b6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending upon the state of the driver, there are several potential
pitfalls on remove. Kill the watchdog task so rmmod doesn't hang.
Check the adapter->msix_entries field, not the num_msix_vectors field,
which is never cleared.
Change-ID: I0546048477f09fc19e481bd37efa30daae4faa88
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We remove all the MAC filters, so remove the VLAN filters, too.
Change-ID: I4f7559acdf005dc3f359bf6460ce32d183c8878b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the kernel watchdog bites us, ask the PF to reset us and attempt to
reinit the driver.
Change-ID: Ic97665aeeed71ce712b9c4f057e78ff8372522b9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respond better to a VF reset event. When a reset is signaled by the
PF, or detected by the watchdog task, prevent the watchdog from
processing admin queue requests, and schedule the reset task.
In the reset task, wait first for the reset to start, then for it to
complete, then reinit the driver.
If the reset never appears to complete after a long, long time (>10
seconds is possible depending on what's going on with the PF driver),
then set a flag to indicate that PF communications have failed.
If this flag is set, check for the reset to complete in the watchdog,
and attempt to do a full reinitialization of the driver from scratch.
With these changes the VF driver correctly handles a PF reset event
while running on bare metal, or in a VM.
Also update copyrights.
Change-ID: I93513efd0b50523a8345e7f6a33a5e4f8a2a5996
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we store the traffic vector names in the queue vector struct, we
don't need to maintain an array of strings for these names in the
adapter structure. Replace this array with a single string and use it
when allocating the misc irq vector.
Also update copyrights.
Change-ID: I664f096c3c008210d6a04a487163e8aa934fee5b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the device ID #defines to follow the _DEV_ID convention
already established in the other Intel drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the driver for the Intel(R) XL710 X710 Virtual Function.
This patch contains the main driver entry points, but does not include
transmit and receive or ethtool functionality, which are presented as
separate patches in this series.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
