Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver can be used on Xilinx ARM Zynq platform
where in_be32/out_be32 functions are not implemented.
Use __raw_readl/__raw_writel functions which are
implemented on Microblaze and PowerPC.
For ARM readl/writel functions are used instead.
The correct way how to implement this is to detect
endians directly on IP. But for the gpio case
without interrupt connected(it means without
interrupt logic) there are just 2 registers
data and tristate where auto detection can't be done.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Supporting the second channel in the driver.
Offset is 0x8 and both channnels share the same
IRQ.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplification is done by using OF helper function
which increase readability of code and remove
(if (var) var = be32_to_cpup;) assignment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a kernel message, containing GPIO range and device
name on successful device registration, and removes duplicate messages from the following drivers:
* gpio-adp5588
* gpio-bt8xx
* gpio-cs5535
* gpio-janz-ttl
* gpio-nomadik
* gpio-pcf857x
* gpio-xilinx
* drivers/of/gpio.c
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
[grant.likely@secretlab.ca: squashed 2 patches together]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in gpio
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Sort the gpio makefile and enforce the naming convention gpio-*.c for
gpio drivers.
v2: cleaned up filenames in Kconfig and comment blocks
v3: fixup use of BASIC_MMIO to GENERIC_GPIO for mxc
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
