Bump to version 0.3.36 for i40e and 0.9.16 for i40evf.
Change-ID: I7b4ff97b32d2825181803c03c316381a7608a618
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a feature to avoid updating the descriptor
ring by marking each descriptor with a DD bit, and instead
writes a memory location with an update to where the driver
should clean up to. Enable this feature.
Change-ID: I5da4e0681f0b581a6401c950a81808792267fe57
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up and moves a portion of i40e_open to i40e_vsi_open,
in order to have a shorter vsi_open function that does only that.
Change-ID: I1c418dda94dcfc0eb7d4386a70c330692ef5ecc9
Signed-off-by: Elizabeth Kappler <elizabeth.m.kappler@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables option '-k/-K' in ethtool for NTUPLE control.
NTUPLE control requires a reset, to take effect. When the feature is
turned off, the SW list of stored FD SB filters gets cleaned up.
Change-ID: I9d564b67a10d4afa11de3b320d601c3d2e6edc1f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This netdev op allows the PF driver to control the virtual link state of
the VF devices. This can be used to deny naughty VF drivers access to
the wire, or to allow VFs (regardless of temperament) to communicate
with each other over the device's internal switch even though external
link is down.
Add the actual ndo function, and modify vc_notify_link_state to check
the link status of each VF before sending a message in the case when
physical link changes state.
Change-ID: Ib5a6924da78c540789f21d26b5e8086d71c29384
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The networking core does it for the driver during registration time.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Linux 3.13, dma_set_mask_and_coherent was introduced, and we have
been encouraged to use it. It simplifies the DMA mapping code a bit as
well.
Change-ID: I66e340245af7d0dedfa8b40fec1f5e352754432e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have a separate handler for MDD events, a generic reset is not required.
Change-ID: I77858e2d479e4e65c52aede67109464649ea0253
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FDIR replay logic was being run a little too soon (before the
queues were enabled) and hence the tail bump was not effective till
a later transaction happened on the queue.
Change-ID: Icfd7cd2e79fc3cae3cbd3f703a2b3a148b4e7bf6
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to enforce the following policy:
- If the HW reports filter programming error, we check if it's due to a
full table.
- If so, we go ahead and turn off new rule addition for ATR and then SB
in that order.
- We monitor the programmed filter count, if enough room is created due
to filter deletion/reset, we then re-enable SB and ATR new rule addition.
Change-ID: I69d24b29e5c45bc4fa861258e11c2fa7b8868748
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In a similar way to how ixgbe works, print a short one-line string
showing what features and number of queues the driver and hardware has
enabled at probe time.
Example (wrapped for the commit message):
i40e 0000:06:00.1: Features: PF-id[1] VFs: 64 VSIs: 66 QP: 32 FDir RSS
ATR NTUPLE DCB
Change-ID: I177bf7f93d1c4c921529c92fdf66e614f6b4f755
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the strings that the driver prints during normal
operation and moves many strings into dev_dbg. It also cleans up
strings printed during reset.
Change-ID: I1835cc4e3c3b22596182b683284e6bb87eac61b2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This cleans up strings for consistency, q is replaced with queue.
Change-ID: Ia5f9dfae9af261f4c24485854264e02363729cf3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We've been deleting the netdev before getting around to deleting the napi
structs. Unfortunately, we then didn't delete the napi structs because we
have a check for netdev, thus we were leaving garbage around in the system.
Change-ID: Ife540176f6c9f801147495b3f2d2ac2e61ddcc58
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver needs to use the format that the current NVM
uses when printing the version of the NVM. It should remain
this way from now on forward.
The driver was reporting when firmware was less than
an expected version number, but this is not a requirement
for the product and we print the firmware number at
init and in ethtool -i output. Just remove the print.
Change-ID: Ide0b856cd454ebf867610ef9a0d639bb358a4a60
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Number of MSIX vectors being reported is correct and hence
we need a check to do the right thing for FWs before and after.
Change-ID: I50902d1c848adcb960ea49ac73f7865ca871a1c3
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix inconsistent use of MSIX and MSI-X in messages.
Change-ID: Iae9ffb42819677c34544719044ed77632e06147d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the do/while to a for loop, so we don't hit the delay each
time, even when the register is ready for action.
Don't bother to set or clear the QENA_STAT bit as it is
read-only.
Change-ID: Ie464718804dd79f6d726f291caa9b0c872b49978
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the DOWN flag before attempting to disable VFs when unloading the
driver. Also, don't attempt to reset the VFs when the driver is
unloading, because the switch configuration will fail. This fixes a
panic on unload when VFs are enabled.
Change-ID: I25a6567e89c9687145f510ff4f630932412c5c5d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VFs are present when the driver loads, then set up some resources
so they can function.
Change-ID: I485916a811609a9990ce663d06dc645f625b07ff
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset all of the VFs after a PF reset, so that they are in a known
state, and the VF driver can detect the reset and reinit itself.
Change-ID: I93c5b3a0f8b1371d0da078f92de948b9d3a6413f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tx_timeout recovery failed, then it becomes necessary to set
i40e_down bit before actually shutdown the connection.
Change-ID: Iaac81df0e302116571827aa0cff450697fbb7fa3
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version to 0.3.31-k.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indentation mismatch spotted with Coverity.
Introduced in 4e3b35b044 ("i40e: add DCB and DCBNL support")
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the device ID #defines to follow the _DEV_ID convention
already established in the other Intel drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds capability to configure DCB on i40e network
interfaces using Intel XL710 adapter firmware APIs.
By default all VSIs are only enabled for the default traffic
class enabled by firmware for any given PF. The driver would
query the firmware for the traffic classes that are enabled for
the port and reconfigure the LAN VSI to match to the port traffic
class settings. All other VSIs are only enabled for the default
traffic class settings for now.
The driver registers and listens to firmware events that may
require change in the DCB settings. It may reconfigure the VSI
settings based on these events.
This patch exposes IEEE DCBNL interfaces for the i40e driver to
allow any application to query the DCB settings on the adapter.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e hardware was generating some inconsistent results
when using current programming methods. This refactor
fixes the inconsistencies that were preventing clean
unloads of the driver, and moves the queues for handling
flow director errors into their own hardware VSI.
This patch also implements a corrected version of the
basic ethtool add ntuple rule, which will disable
the driver's automatic flow programming. A future patch
adds remove/replay/list support for ntuple.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FLAG_FDIR_* defines can be renamed to be more descriptive.
This patch is in preparation for the following where the fdir
code is refactored.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix more whitespace issues, including making some locals declared
in a nicer order.
Also update Copyright string printed when the driver loads.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a workaround that is no longer necessary and implement
a better understanding of what firmware is returning in the MSI-X
vector count. This makes it so that the driver ends up with the
right amount of queues when using all available MSI-X vectors.
Change-ID: I34e60cc71dcfb1b5412f37df956fedcc49ade187
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On port VLAN deletion the list of MAC filters for the virtual function (VF)
VSI were all deleted. Let's keep them around, they come in handy for keeping
the VF functional.
Change-Id: I335e760392f274dc8b8b40efcb708f65b49d7973
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version to 0.3.30-k.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some whitespace and comment issues.
Change-ID: I1587599e50ce66fd389965720e86f9e331d86643
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug where the queue was not associated with the right set-up
within the hardware. The fix is to use the right QTX_CTL VSI type
when associating it to the VSI.
Change-ID: I65ef6c5a8205601c640a6593e4b7e78d6ba45545
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version to 0.3.28-k.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New feature: Enable PTP support in the i40e driver.
Change-ID: I6a8e799f582705191f9583afb1b9231a8db96cc8
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the latest firmware the clear_pxe_mode function will use the
AdminQ request, so call this after AdminQ is set up rather than
relying on i40e_pf_reset() to clear the PXE mode.
Change-ID: Ice8cba2e9cbc3c7bde0a0bcf8eaf5009abef040b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the "new" qtx_head[q] register is cleared before
enabling the Tx queue.
Change-ID: I0c7a12815e343a5ae68807af172a35d6c6857935
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where the driver was erroneously exiting the driver unload
path if one part of the unload failed. Instead of the original way
the driver should always continue when disabling and be sure to disable
all queues.
Change-ID: Ib8c81c596bc87c31d8e9ca97ebf871168475279d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver needs to set the MFP flag earlier in i40e_sw_init
and then can use that flag to decide if other hardware
work-arouds are required.
Change-ID: Ib17ad1e3485f57b28845ab4722294a99f203bd48
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The alloc_rx_buff_failed and alloc_rx_page_failed variables
are both part of an rx specific structure so just remove
the _rx part of the name. No functional changes.
Change-ID: Icffa2f5d13c6f2b1e09cf45b9472b83c9dae8fc6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The admin queue can be used to send messages among the physical
function interfaces. This adds the code to handle that case.
Change-ID: I0700fcc47e41433131a381f0eb72fc7b01b6bd87
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSS initialization was doing some extra work, remove the extra
work and any bugs it created when managing number of queues.
Change-ID: Iea75b04a70d73ce76947b6a177ce89ab4899d4c6
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver and hardware support splitting packets on headers
but with the use of GRO we don't need the extra bus
overhead, so make this driver more like igb and ixgbe and
disable packet split.
Change-ID: Id42f2c3736baa9d5bdfe1f72d64226e7d8ebd737
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The memory barrier used in maybe_stop_tx can use a comment.
Also add checks to VSI->rx_rings to ensure a kernel panic is not induced.
Change-ID: I48cc1bf1d6cf301818155b737edeef77c0d790c7
Change-ID: I1363a8445fbf521a26267849966296ed55f43ad8
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The GPL header included in each file in the i40e driver doesn't
need to include the "this program" text since this driver
is already part of the larger kernel.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware can occasionally give an interrupt on the misc
queue for which there is no driver work to do. In that case
the driver was not re-enabling interrupts even though they
were auto masked by hardware. This left interrupts disabled
on this queue.
Re-enable the interrupt whenever leaving this function.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the 8021q driver is loaded it sets VLAN 0 filters on all devices.
This does not mean that any VLAN tagged packet should be accepted.
Instead accept only VLAN 0 tagged packets so that upper layers can
interpret the priority bits.
Change-Id: I17274a540b613749612ffe23a3aef2b8ee6ff6a4
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Broadcast promiscuous should only be turned on when general
promiscuous mode is turned on, otherwise VLAN tagged packets out of
the assigned VLAN domain are received.
Add a broadcast MAC filter in order to continue to receive
broadcast traffic on VLANs, MAIN or VMDQ VSI.
Change-Id: I99d8e382a082ee51201228f1226af3b46452ac55
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the device is not in a working state avoid making admin
queue (AQ) calls that rely on a working AQ.
Change-Id: Ifbba6d257b3a5b51bfe92938c04088c0baa21433
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver needs to make sure the send queue is alive before
trying to use it.
Chagne-Id: I9bd1f6159c45c98e63f562e3a8dfb57edfe50e13
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Always call the AQ call to shutdown the queue in the shutdown path.
Check ASQ is alive before issuing the AQ command since we might be
resetting to recover from a bad state in which case we should not
issue the AQ command.
Use the register variable for length so it can be used by PF, VF
and GL AQ commands.
Change-Id: Ic3d305687ea3f1a6afa84e864b7a27bd38a9af32
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF VSI Port VLAN settings still allow the user to view VLAN tag in
the descriptor. Fix the settings to hide the VLAN ID from the VF. The
VF is not supposed to be aware it is on a VLAN in the Port VLAN
scenario.
Change-Id: I976f2bacb455dbb750f8c53a781c689f02cb8907
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shockingly, the compiler didn't flag this uninitialized variable. This
fixes a potential memory corruption condition where ARQ messages are
written to random memory locations.
Change-Id: Iac82f4562d2bf3f42df3f3b2163d9cbed2160135
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling the default port on the VEB causes all outgoing traffic from
virtual functions to be copied to the physical function. The default
port is only supposed to be used if you wish to bridge the physical
function to a SW switch such as Open vSwitch or the Linux bridge. That
allows the SW switch to route traffic to VMs that are not using a
virtual function.
Eventually we'll want to implement the ndo_fdb_add, ndo_fdb_del, and
ndo_fdb_dump functions. The ndo_fdb_add function would set the
default port on the VEB in those cases where the MAC/VLAN address
filters have overflowed. Normally we would not want to use it.
Change-Id: I3990f0384fff2840c4e43bc0955dd0b701380852
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes two different problems.
1) The port VLAN configuration was not persistent across VF driver
loads and unloads.
2) The port VLAN configuration was only correct the first time it was
set. Switching the port VLAN on and off would cause subsequent VLAN
configurations to be corrupted in the VSI. Ensure that the correct
bits are being set for the VSI port VLAN configuration.
Change-Id: I7ebf5329f77eb8d73ccd3324eb346b3abeea737d
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver needs to clean PBA only when interrupts are turned off and we
are polling instead.
Change-Id: Ic0c1da761bd3abe7f73b1cc8bcddf8e3a232fd0f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove references to I40E_FLAG_MQ_ENABLED from the code
as it doesn't seem to be used anywhere.
Change-Id: I4c89fb65b2cdd26fbb0c58fccbbb4b03f0e5f1b3
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The allocation and clearing of rings for a VSI should be
using the alloc_queue_pairs and not num_queue_pairs.
The alloc_queue_pairs per VSI is a pre-allocated number
of queues assigned to a VSI; based on number of TCs enabled
only certain number of queues may be used from that. This
is mainly valid only for the LAN VSI case as that is the
only VSI that may be enabled with multiple traffic classes.
In the future the number of TCs may change based on DCBX
configuration.
The actual number of queues that are enabled/configured is
based on the number of TCs enabled for a given VSI and that
is stored in num_queue_pairs.
With this change num_[tr]x_queues is unused so remove them.
Change-Id: I9c2f84778bb25f7313c630e9b002a0caa883ce29
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't try to free a q_vector that hasn't been set up as it can
panic the kernel.
Change-Id: I0650cc6c441d0779788c522c790293c276d14fbc
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Swap a couple lines around in the error handling if the kzalloc() for
the pf->vsi array fails. This was causing a kernel BUG because the
call to i40e_clear_interrupt_scheme() was assuming the pf->vsi[] array
existed. In this fix it is possible that i40e_reset_interrupt_capability()
will get called twice, but this is a safe action.
Change-Id: I939163ccaa89baac7511556d36bc873864c35ae1
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When cleaning the ARQ, we must reinitialize the buffer size each time we
go through the loop, because i40e_clean_arq_element returns the message
length in the same field. Without this change, subsequent messages can
be truncated to the length of the previous message.
Change-Id: Ic9c32ff843faf0fc3196d21351a1c3a60c6158eb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce i40e_irq_dynamic_disable_icr0 and use it and its previously-
extant counterpart when appropriate.
Change-Id: Ieb4037874fba2e96fc2354b34a97a3cb8f6490f3
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove custom i40e functions around ethernet addresses that are
duplicating already existing kernel functionality.
Also ends up fixing a bug with multicast addresses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make a define used in the header file by both VF and PF drivers.
Change-Id: Ie9e35adcc021cd6a8f7513934984eb4ed55774f5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't complain when we disable queues that are already disable, or
enable them when they're already enabled. This removes a bunch of bogus
log messages that we see at every VF reset.
Change-Id: Ia127be572abdccc48a53d8c43f8a07b8bb920de1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the VF reset flow so that it works on real hardware. After
discussions with the HW team, the reset flow has been changed
somewhat.
- Change the i40e_reset_vf function to a void type, and fix
up the callers to reflect this.
- Move the MSI-X disable code to i40e_free_vf_res since it must
be done every time the VF is freed, regardless of whether or
not it is reset.
- Ensure that the PCIe bus is quiet before polling the reset bit.
- Don't clear the VFGEN_RSTAT1 register at the beginning as it is
cleared by the reset.
- Poll longer for the reset to be done.
- Disable the queues using an existing function rather than
rolling our own.
- Free and reallocate the VSI after reset to avoid rx hang.
Change-Id: I11e2590431cb73e8663714d1cc5b23d59b809033
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds the implementation for the VXLAN ndo's. This allows the
hardware to do RX checksum offload for inner packets on the UDP ports
that VXLAN notifies us about.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add curly-braces on a multi-line function. While we're here we
also change to return void in i40e_vsi_clear_rings() since no
caller cares.
Change-Id: I261fcef20e2a39e18d83ec08fdd14456131dee91
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wake on LAN is disabled by default and will remain that way for most
platforms, but there is an NVM setting that allows vendors to enable it
for a port if they think they've provided the right power environment
for the device. This patch adds code to check the NVM setting and enable
Magic Packet use if WoL is enabled for the port.
Since only Magic Packet is supported, there's not a lot of HW configuration
needed.
Change-Id: I44e904a7b15695e34683009f487064cd86ea59b0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call i40e_set_pci_config_data from probe, then check that
we are in a 8GT/s x8 PCIe slot and send a warning if we are not.
Change-Id: I62815c574cee50d2787c50bbe956dde7a7a75a11
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HMC error interrupt would generate an un-necessary message
"unhandled interrupt", causing extra log spam, in addition to causing
a reset that was not necessary. Prevent this issue by handling the
HMC error case explicitly, and only reset if the interrupt was from
some of the other causes.
Change-Id: Iabd203ba1dfc26a136b638597f3e9991acfa29f3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
No functional change, but the wrong defines were being used.
Change-Id: Ica2afd2dfe18154ca0f1260a508f31e372319ba7
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Any user-initiated path which eventually calls reset needs
to hold the rtnl_lock, so add functionality to do that.
Be careful not to use the safe reset when cleaning up
from the diagnostic tests, which avoids rtnl_lock
recursion from ethtool.
Protect the reset_task with rtnl_lock, since it runs from a work item.
Change-Id: Ib6e7a3fb2966809db2daf35fd5a123ccdf6f6f0f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the second of 3 patches that allows for changing
the number of queues in the driver on the fly.
This patch adds a function that calls the reinit flow for the
main VSI after making changes to the RSS queue count as requested
by the user.
Change-Id: I82dee91e9fe90eeb4e84a7369f4b8b342155dd85
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is the first in a 3 series patchset to implement
dynamically changing the queue count for the main VSI.
This patch starts by adding a reinit flow. This flow is designed
to be able to change just the queue count and not the number of
interrupt vectors that the device originally came up with.
Change-Id: I0634aaebf7dc4dd6c66af8f9dbbef89d7beac438
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current driver default sets the number of transmit/receive
queue pairs based on the current node's CPU count.
A better method is to use the total number of CPUs in the system
to suggest the number of queue pairs, which aligns better with
the behavior of ixgbe, and also with the expectations of the
kernel XPS and other subsystems in the stack.
Change-Id: If3e20c7f100f13e51d69762594d948f247ffe0c8
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prevent some compiler warnings and implement some other
trivial fixes.
Change-Id: I7f49d79b91b94df1ad4a8306a0410ed72238845f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor flow control set up and disable L2 flow
control by default.
Change-Id: I2fe257b80df6d9a1e37deb4df118da8f8467040d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call the netif_set_real* functions in order to make sure
the stack knows about how many queues we have, in order
for RFS/RPS/XFS to work correctly.
Change-Id: Ib7a7b2792f80c5eef210dedf42cc6607d63953d2
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the vsi->tx_rings structure is NULL we don't want to panic.
Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the number of physical functions (PFs) found, this is a global counter
on purpose so that each pf loaded has a unique ID.
Change-Id: I74d618520afbce4a774d0235449e3b5f97ff6d4a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print a message to notify the user of how many VFs are initialized on each
port.
Change-Id: I29ac2acc478ee4e588fd6ffcc35133d4c6607ca9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VSI may be allocated more queues (alloc_queue_pairs) than actually
are to be used (num_queue_pairs), so only allocate rings for the queues
to be used. The numbers will likely be the same for most VSIs, but can
be different based on how TCs are assigned and enabled.
Change-Id: Ie40f7ad0affbc4b45d6f049bcf02ee2fa24edc74
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSS can steer packets based on recognition of all
sorts of different headers. Enable some more of them.
Change-Id: I2264dedae66fb0bceca6fb6e772e050e3ca8efc8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to re-size queues and vectors while the interface is
still up, we need to be able to call functions to free and
re-allocate without bringing down the VSI.
We also need to reset the existing setup, update the
configuration and then rebuild again. This requires us to have
the reset flow broken down into two parts.
Change-Id: I374dd25aabf769decda69b676491c7b7730a4635
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
