Clock adjustment data should be passed to FW as well, otherwise in some
cases a drift was observed when using GPIO features.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Artificial HW reliability tests revealed a possible hangup in
the driver. Normally, when device disappears from bus, all
register reads returns 0xFFFFFFFF.
At remote procedure invocation towards FW there is a logic
where result is compared with -1 in a loop.
That caused an infinite loop if hardware due to some issues
disappears from bus.
Add extra result checks to prevent this.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yet another checksum offload compatibility issue was found.
The known issue is that AQC HW marks tcp packets with 0xFFFF checksum
as invalid (1). This is workarounded in driver, passing all the suspicious
packets up to the stack for further csum validation.
Another HW problem (2) is that it hides invalid csum of LRO aggregated
packets inside of the individual descriptors. That was workarounded
by forced scan of all LRO descriptors for checksum errors.
However the scan logic was joint for both LRO and multi-descriptor
packets (jumbos). And this causes the issue.
We have to drop LRO packets with the detected bad checksum
because of (2), but we have to pass jumbo packets to stack because of (1).
When using windows tcp partner with jumbo frames but with LSO disabled
driver discards such frames as bad checksummed. But only LRO frames
should be dropped, not jumbos.
On such a configurations tcp stream have a chance of drops and stucks.
(1) 76f254d4af ("net: aquantia: tcp checksum 0xffff being handled incorrectly")
(2) d08b9a0a3e ("net: aquantia: do not pass lro session with invalid tcp checksum")
Fixes: d08b9a0a3e ("net: aquantia: do not pass lro session with invalid tcp checksum")
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of autosuspend, at91ether_start is called with clocks disabled.
Ensure that pm_runtime doesn't suspend the interface as soon as it is
opened as there is no pm_runtime support is the other relevant parts of the
platform support for at91rm9200.
Fixes: d54f89af6c ("net: macb: Add pm runtime support")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0290bd291c ("netdev: pass the stuck queue to the timeout handler")
introduced a new argument to the function but missed adding the description
of the argument to the function header comment. Add it now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"fallthrough" comments are used in switch case statements to explicitly
indicate the code is intended to fall through to the following statement.
Different variants of "fallthough" are acceptable, e.g. "fall through",
"fallthrough", "Fall-through". The GCC compiler has an optional warning
(-Wimplicit-fallthrough[=n]) to warn when such a comment is not present;
the default version of which is enabled when compiling the Linux kernel.
There have been recent discussions in kernel mailing lists regarding
replacing non-standardized "fallthrough" comments with the pseudo-reserved
word 'fallthrough' which will be defined as __attribute__ ((fallthrough))
for versions of gcc that support it (i.e. gcc 7 and newer) or as a nop
for versions that do not. Replace "fallthrough" comments with fallthrough
reserved word.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fallthrough comments are used to explicitly indicate the code is intended
to flow from one case statement to the next in a switch statement rather
than break out of the switch statement. They are only needed when a case
has one or more statements to execute before falling through to the next
case, not when there is a list of cases for which the same statement(s)
should be executed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in ice_vc_ena_qs_msg() we are incorrectly validating the
virtchnl queue select bitmaps. The virtchnl_queue_select rx_queues and
tx_queue bitmap is being compared against ICE_MAX_BASE_QS_PER_VF, but
the problem is that these bitmaps can have a value greater than
ICE_MAX_BASE_QS_PER_VF. Fix this by comparing the bitmaps against
BIT(ICE_MAX_BASE_QS_PER_VF).
Also, add the function ice_vc_validate_vqs_bitmaps() that checks to see
if both virtchnl_queue_select bitmaps are empty along with checking that
the bitmaps only have valid bits set. This function can then be used in
both the queue enable and disable flows.
Arkady Gilinksky's patch on the intel-wired-lan mailing list
("i40e/iavf: Fix msg interface between VF and PF") made me
aware of this issue.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VF driver sends the PF a request to disable Rx queues
we will disable them one at a time, even if the VF driver sent us a
batch of queues to disable. This is causing issues where the Rx queue
disable times out with LFC enabled. This can be improved by detecting
when the VF is trying to disable all of its queues.
Also remove the variable num_qs_ena from the ice_vf structure as it was
only used to see if there were no Rx and no Tx queues active. Instead
add a function that checks if both the vf->rxq_ena and vf->txq_ena
bitmaps are empty.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are not handling LAN overflow events. There can be cases
where LAN overflow events occur on VF queues, especially with Link Flow
Control (LFC) enabled on the controlling PF. In order to recover from
the LAN overflow event caused by a VF we need to determine if the queue
belongs to a VF and reset that VF accordingly.
The struct ice_aqc_event_lan_overflow returns a copy of the GLDCB_RTCTQ
register, which tells us what the queue index is in the global/device
space. The global queue index needs to first be converted to a PF space
queue index and then it can be used to find if a VF owns it.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in ice_vsi_get_qs() we set the mapping_mode for Tx and Rx to
vsi->[tx|rx]_mapping_mode, but the problem is vsi->[tx|rx]_mapping_mode
have not been set yet. This was working because ICE_VSI_MAP_CONTIG is
defined to 0. Fix this by being explicit with our mapping mode by
initializing the Tx and Rx structure's mapping_mode to
ICE_VSI_MAP_CONTIG and then setting the vsi->[tx|rx]_mapping_mode to the
[tx|rx]_qs_cfg.mapping_mode values.
Also, only assign the vsi->[tx|rx]_mapping_mode when the queues are
successfully mapped to the VSI. With this change there was no longer a
need to initialize the ret variable to 0 so remove that.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when we enable/disable all Rx queues we do the following
sequence for each Rx queue and then move to the next queue.
1. Enable/Disable the Rx queue via register write.
2. Read the configuration register to determine if the Rx queue was
enabled/disabled successfully.
In some cases enabling/disabling queue 0 fails because of step 2 above.
Fix this by doing step 1 for all of the Rx queues and then step 2 for
all of the Rx queues.
Also, there are cases where we enable/disable a single queue (i.e.
SR-IOV and XDP) so add a new function that does step 1 and 2 above with
a read flush in between.
This change also required a single Rx queue to be enabled/disabled with
and without waiting for the change to propagate through hardware. Fix
this by adding a boolean wait flag to the necessary functions.
Also, add the keywords "one" and "all" to distinguish between
enabling/disabling a single Rx queue and all Rx queues respectively.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VF can see other's broadcast and multicast traffic because
it always has a VLAN filter for VLAN 0. Fix this by removing/adding the
VF's VLAN 0 filter when a port VLAN is added/removed respectively.
This required a few changes.
1. Move where we add VLAN 0 by default for the VF into
ice_alloc_vsi_res() because this is when we determine if a port VLAN is
present for load and reset.
2. Moved where we kill the old port VLAN filter in
ice_set_vf_port_vlan() to the very end of the function because it allows
us to save the old port VLAN configuration upon any failure case.
3. During adding/removing of a port VLAN via ice_set_vf_port_vlan() we
also need to remove/add the VLAN 0 filter rule respectively.
4. Improve log messages.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when configuring a port VLAN for a VF we are only shifting the
QoS bits by 12. This is incorrect. Fix this by getting rid of the ICE
specific VLAN defines and use the kernel VLAN defines instead.
Also, don't assign a value to vlanprio until the VLAN ID and QoS
parameters have been validated.
Also, there are many places we do (le16_to_cpu(vsi->info.pvid) &
VLAN_VID_MASK). Instead do (vf->port_vlan_info & VLAN_VID_MASK) because
we always save what's stored in vsi->info.pvid to vf->port_vlan_info in
the CPU's endianness.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for vf->link_up is incorrect because this field is only valid if
vf->link_forced is true. Fix this by adding the helper ice_is_vf_link_up()
to determine if the VF's link is up.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ice_vsi_manage_pvid() calls
ice_vsi_[set|kill]_pvid_fill_ctxt() when enabling/disabling a port VLAN
on a VSI respectively. These two functions have some duplication so just
move their unique pieces inline in ice_vsi_manage_pvid() and then the
duplicate code can be reused for both the enabling/disabling paths.
Before this patch the info.pvid field was not being written
correctly via ice_vsi_kill_pvid_fill_ctxt() so it was being hard coded
to 0 in ice_set_vf_port_vlan(). Fix this by setting the info.pvid field
to 0 before calling ice_vsi_update() in ice_vsi_manage_pvid().
We currently use vf->port_vlan_id to keep track of the port VLAN
ID and QoS, which is a bit misleading. Fix this by renaming it to
vf->port_vlan_info. Also change the name of the argument for
ice_vsi_manage_pvid() from vid to pvid_info.
In ice_vsi_manage_pvid() only save the fields that were modified
in the VSI properties structure on success instead of the entire thing.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow support for S-Tag + C-Tag VLAN traffic by disabling pruning when
there are no 0x8100 VLAN interfaces currently created on top of the PF.
When an 0x8100 VLAN interface is configured, enable pruning and only
support single and double C-Tag VLAN traffic. If all of the 0x8100
interfaces that were created on top of the PF are removed via
ethtool -K <iface> rx-vlan-filter off or via ip tools, then disable
pruning and allow S-Tag + C-Tag traffic again.
Add VLAN 0 filter by default for the PF. This is because a bridge
sets the default_pvid to 1, sends the request down to
ice_vlan_rx_add_vid(), and we never get the request to add VLAN 0 via
the 8021q module which causes all untagged traffic to be dropped.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The IPv6 address defined in struct in6_addr is specified as
big endian, but there is no specified endian in struct
hclge_fd_rule_tuples, so it will cause a problem if directly
use memcpy() to copy ipv6 address between these two structures
since this field in struct hclge_fd_rule_tuples is little endian.
This patch fixes this problem by using be32_to_cpu() to convert
endian of IPv6 address of struct in6_addr before copying.
Fixes: d93ed94fbe ("net: hns3: add aRFS support for PF")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling 4 TC after setting the bandwidth of VF, the bandwidth
of VF will resume to default value, because of the qset resources
changed in this case.
This patch fixes it by using a fixed VF's qset resources according to
HNAE3_MAX_TC macro.
Fixes: ee9e44248f ("net: hns3: add support for configuring bandwidth of VF on the host")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current process, the management table is missing after the
IMP reset. This patch adds the management table to the reset process.
Fixes: f5aac71c03 ("net: hns3: add manager table initialization for hardware")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With multiple VIFS ath10k, and probably others, tries to find the
minimum txpower for all vifs and uses that when setting txpower in
the firmware.
If a second vif is added and starts to scan, it's txpower is not
initialized yet and it set to zero.
ath10k had a patch to ignore zero values, but then it is impossible
to actually set txpower to zero.
So, instead initialize the txpower to INT_MIN in mac80211, and let
drivers know that means the power has not been set and so should
be ignored.
This should fix regression in:
commit 88407beb1b
Author: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Date: Tue Dec 13 14:55:19 2016 -0800
ath10k: fix incorrect txpower set by P2P_DEVICE interface
Tested on ath10k 9984 with ath10k-ct firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191217183057.24586-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Because wireguard is calling icmp from network device context, it should
use the ndo helper so that the rate limiting applies correctly. This
commit adds a small test to the wireguard test suite to ensure that the
new functions continue doing the right thing in the context of
wireguard. It does this by setting up a condition that will definately
evoke an icmp error message from the driver, but along a nat'd path.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because sunvnet is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly. While we're
at it, doing the additional route lookup before calling icmp_ndo_send is
superfluous, since this is the job of the icmp code in the first place.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because gtp is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Formatting strings in print function calls (like dev_info, dev_err, etc.)
can exceed 80 columns without making checkpatch unhappy. So remove
newlines where applicable and make print statements more compact.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use ice_pf_to_dev(pf) instead of &pf->pdev->dev
Use ice_pf_to_dev(vsi->back) instead of &vsi->back->pdev->dev
When a pointer to the pf instance is available, use ice_pf_to_dev
instead of ice_hw_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 1f45ebe0d8 ("ice: add extra check for null Rx descriptor") moved
the call to ice_construct_skb() under a null check as Coverity reported a
possible use of null skb. However, the original call was not deleted, do so
now.
Fixes: 1f45ebe0d8 ("ice: add extra check for null Rx descriptor")
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After a reset the Unit Load Status bits in the GLNVM_ULD register to check
for completion should be 0x7FF before continuing. Update the mask to check
(minus the three reserved bits that are always set).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Logging the firmware/NVM information during driver load is redundant since
that information is also available via ethtool. Move the functionality
found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove
calling the former and logging that info during driver probe. This also
gets rid of a bug in ice_nvm_version_str() where it returns a pointer to
a buffer which is free'ed when that function exits.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unnecessary CONFIG_PCI_IOV wrapping in ice_set_pf_caps. None
of the data structures accessed within the block are wrapped with
this flag. When CONFIG_PCI_IOV is undefined, pf->num_vfs_supported
will be 0 anyway.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we compare the value we are about to write to the Rx tail
register with the previous value of next_to_use. The problem with this
is we only write tail on 8 descriptor boundaries, but next_to_use is
updated whenever we clean Rx descriptors. Fix this by comparing the
value we are about to write to tail with the previously written tail
value. This will prevent duplicate Rx tail bumps.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Display all of the supported and advertised link modes based on the PHY
capability with media.
Displaying all supported modes is more informative then only displaying
the current link mode.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When switching between FW and SW LLDP mode, the
number of configured TLV apps in the driver's
DCB configuration is getting out of synch with
what lldpad thinks is configured. This is causing
a problem when shutting down lldpad. The cleanup
is trying to delete TLV apps that are not defined
in the kernel.
Since the driver is keeping an accurate account
of the apps defined, use the drivers number of
apps to determine if there is an app to delete.
If the number of apps is <= 1, then do not
attempt to delete.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ice_dcb_rebuild had some logic
flaws in it, and also didn't differentiate
between FW and SW modes needs.
For FW flow, the willing setting was being
forced to OFF and left that way. Unwilling
in DCB FW mode is not a supported model.
Leave the config alone and use the return value
from the set command to determine if setting the
config was successful.
The SW DCB flow does not need to need to register
for MIB change events (as they are not used in
SW mode).
Use !is_sw_lldp checks to only perform FW specific
task while in FW mode.
Also adding a reapplication of the current DCB
config after a link event. Some NVMs are not
maintaining their DCB configs across link events.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows you to specify the type of rgmii-id that will enable phy
internal delay in ethernet phy-mode.
This adds all RGMII cases to all of get_pinmode() except LD11, because LD11
SoC doesn't support RGMII due to the constraint of the hardware. When RGMII
phy mode is specified in the devicetree for LD11, the driver will abort
with an error.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent months, our customer reported several kernel crashes all
preceding with following message:
NETDEV WATCHDOG: eth2 (enic): transmit queue 0 timed out
Error message of one of those crashes:
BUG: unable to handle kernel paging request at ffffffffa007e090
After analyzing severl vmcores, I found that most of crashes are
caused by memory corruption. And all the corrupted memory areas
are overwritten by data of network packets. Moreover, I also found
that the tx queues were enabled over watchdog reset.
After going through the source code, I found that in enic_stop(),
the tx queues stopped by netif_tx_disable() could be woken up over
a small time window between netif_tx_disable() and the
napi_disable() by the following code path:
napi_poll->
enic_poll_msix_wq->
vnic_cq_service->
enic_wq_service->
netif_wake_subqueue(enic->netdev, q_number)->
test_and_clear_bit(__QUEUE_STATE_DRV_XOFF, &txq->state)
In turn, upper netowrk stack could queue skb to ENIC NIC though
enic_hard_start_xmit(). And this might introduce some race condition.
Our customer comfirmed that this kind of kernel crash doesn't occur over
90 days since they applied this patch.
Signed-off-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
comp_ctx can be NULL in a very rare case when an admin command is executed
during the execution of ena_remove().
The bug scenario is as follows:
* ena_destroy_device() sets the comp_ctx to be NULL
* An admin command is executed before executing unregister_netdev(),
this can still happen because our device can still receive callbacks
from the netdev infrastructure such as ethtool commands.
* When attempting to access the comp_ctx, the bug occurs since it's set
to NULL
Fix:
Added a check that comp_ctx is not NULL
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up till kernel 4.11 there was no enum defined for crc32 hash in ethtool,
thus the xor enum was used for supporting crc32.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the name suggests ETH_RSS_HASH_NO_CHANGE is received upon changing
the key or indirection table using ethtool while keeping the same hash
function.
Also add a function for retrieving the current hash function from
the ena-com layer.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Saeed Bshara <saeedb@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ena_com_ind_tbl_convert_from_device() has an overflow
bug as explained below. Either way, this function is not needed at
all since we don't retrieve the indirection table from the device
at any point which means that this conversion is not needed.
The bug:
The for loop iterates over all io_sq_queues, when passing the actual
number of used queues the io_sq_queues[i].idx equals 0 since they are
uninitialized which results in the following code to be executed till
the end of the loop:
dev_idx_to_host_tbl[0] = i;
This results dev_idx_to_host_tbl[0] in being equal to
ENA_TOTAL_NUM_QUEUES - 1.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The indirection table has the indices of the Rx queues. When we store it
during set indirection operation, we convert the indices to our internal
representation of the indices.
Our internal representation of the indices is: even indices for Tx and
uneven indices for Rx, where every Tx/Rx pair are in a consecutive order
starting from 0. For example if the driver has 3 queues (3 for Tx and 3
for Rx) then the indices are as follows:
0 1 2 3 4 5
Tx Rx Tx Rx Tx Rx
The BUG:
The issue is that when we satisfy a get request for the indirection
table, we don't convert the indices back to the original representation.
The FIX:
Simply apply the inverse function for the indices of the indirection
table after we set it.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device receives, stores and retrieves the hash function value as bits
and not as their enum value.
The bug:
* In ena_com_set_hash_function() we set
cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func.
(1 << rss->hash_func)
* In ena_com_get_hash_function() we retrieve the hash function and store
it's bit value in rss->hash_func. (Now the bit value of rss->hash_func
is stored in rss->hash_func instead of it's enum value)
The fix:
This commit fixes the issue by converting the retrieved hash function
values from the device to the matching enum value of the set bit using
ffs(). ffs() finds the first set bit's index in a word. Since the function
returns 1 for the LSB's index, we need to subtract 1 from the returned
value (note that BIT(0) is 1).
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
