Clear the struct so that all reserved fields are zero when we
send the struct down to the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_remove_sta_key() function handles removing a key when the
sta doesn't exist anymore. Mistakenly, this was changed to return an
error while fixing another bug.
If the mvm_sta doesn't exist, we continue normally, but just don't try
to remove the igtk key.
Fixes: cd4d23c1ea ("iwlwifi: mvm: Fix removal of IGTK")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we want to stop the recording of the firmware debug
and restart it later without reloading the firmware we
don't need to resend the configuration that comes with
host commands.
Sending those commands confused the hardware and led to
an NMI 0x66.
Change the flow as following:
* read the relevant registers (DBGC_IN_SAMPLE, DBGC_OUT_CTRL)
* clear those registers
* wait for the hardware to complete its write to the buffer
* get the data
* restore the value of those registers (to restart the
recording)
For early start (where the configuration is already
compiled in the firmware), we don't need to set those
registers after the firmware has been loaded, but only
when we want to restart the recording without having
restarted the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ucode_loaded check should be under the mutex, since it can
otherwise change state after we looked at it and before we got
the mutex. Fix that.
Fixes: 5c89e7bc55 ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.
Fixes: 7948b87308 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During d0i3 flow we flush all the queue except from the command queue.
Currently, in this flow the command queue is hard coded to 9.
In DQA the command queue number has changed from 9 to 0.
Fix that.
This fixes a problem in runtime PM resume flow.
Fixes: 097129c9e6 ("iwlwifi: mvm: move cmd queue to be #0 in dqa mode")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Up until now, the driver was comparing the rate reported by the FW and
the rate of the latest LQ command to avoid processing data belonging
to the old LQ command. Recently, FW changed the meaning of the initial
rate field in tx response and it holds the actual rate (which is not
necessarily the initial rate of LQ's rate table). Use instead LQ cmd
color to be able to filter out tx responses/BA notifications which
where sent during earlier LQ commands' time frame.
This fixes some throughput degradation in noisy environments.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* API support for concurrent scheduled scan requests
* API changes for roaming reporting
* BSS max idle support in mac80211
* API changes for TX status reporting in mac80211
* API changes for RX rate reporting in mac80211
* rewrite monitor logic to prepare for BPF filters
* bugfix for rare devices without 2.4 GHz support
* a bugfix for recent DFS changes
* some further cleanups
The API changes are actually at a nice time, since it's
typically quiet just before the merge window, and trees
can be synchronized easily during it.
-----BEGIN PGP SIGNATURE-----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=dYTw
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of patches for -next:
* API support for concurrent scheduled scan requests
* API changes for roaming reporting
* BSS max idle support in mac80211
* API changes for TX status reporting in mac80211
* API changes for RX rate reporting in mac80211
* rewrite monitor logic to prepare for BPF filters
* bugfix for rare devices without 2.4 GHz support
* a bugfix for recent DFS changes
* some further cleanups
The API changes are actually at a nice time, since it's
typically quiet just before the merge window, and trees
can be synchronized easily during it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This field will need to be used again for HE, so rename it now.
Again, mostly done with this spatch:
@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* The firmware for 7265D and 3168 NICs is frozen at version 29;
* Sari continues working heavily on support for A000 series;
* A bunch of fixes;
* Some cleanups here and there;
-----BEGIN PGP SIGNATURE-----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=5wA8
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
One more pull-request intended for 4.12. These are the changes:
* The firmware for 7265D and 3168 NICs is frozen at version 29;
* Sari continues working heavily on support for A000 series;
* A bunch of fixes;
* Some cleanups here and there;
The changes in commit 9415af7f30 ("iwlwifi: mvm: support new binding
API") assigned values that were later memset to 0. Move the memset
earlier.
Fixes: 9415af7f30 ("iwlwifi: mvm: support new binding API")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename current wait_tx_queue_empty to wait_tx_queues_empty since
it waits for multiple queues (up to 32).
Next patch will add a wait for single TX queue which is needed for
gen2 to be scalable for 512.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid using the old define since it will enlarge necessary
structs for previous HW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support change to ADD_STA API to support station types.
Each station is assigned its type.
This simplifies FW handling of the broadcast and multicast
stations:
* broadcast station is identified by its type and not the mac
address.
* multicast queue is no longer treated differently. The opening
and closing of it is done by referring to its station.
There is no need to specify it in the MAC command.
* When disabling TX to all station driver can disable the traffic
on multicast station, so FW doesn't have to do it.
Change is backward compatible.
Change the order of adding and removing the stations according to
FW requirements.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most of the fields aren't needed in new TX path.
Enlarging the struct to 512 queues will consume a lot of memory.
Remove all references to the struct in the new TX path.
Move mac80211 queue mapping outside, since it will be needed per
queue for TVQM mode.
Add warning in paths that shouldn't be hit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most of the dwells are constant across different scan types.
Use defines instead of depending on scan type.
This is needed as preparation to having different scan type per
band.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We use the full station field as sta_id, and never
use the color.
FW are about to clean the color out, so those defines
are incorrect now (and were redundant before).
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can't use IEEE80211_INVAL_HW_QUEUE to mark a queue as
invalid since 255 will be a valid value for a TVQM queue
index.
Use IWL_MVM_INVALID_QUEUE instead for accessing txq_id.
reserved_queue can stay a u8 since reserved_queue is not
used when TVQM is enabled.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
cab_queue can now get bigger than u8, since in TVQM we will support
512 queues..
Support it by maintaining internal mapping between the actual number
and mac80211 queue (IWL_MVM_DQA_GCAST_QUEUE).
For pre-a000 the internal queue will be the same as the mac80211
queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Wifi mcc (mobile country code) update is forbidden while associated.
Currently, FW prevents these updates and the driver is unaware to
this logic. From now on, the FW sends every wifi mcc update to the
driver. The driver in his turn needs to decide whether to
ignore it or not, depends on the association state.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The reserved queue is never used, save the trouble.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove an extra variable 'queue' that already exists.
Also, since there are no code paths that use 'queue'
without intializing it, remove the unnecessary zero
initialization.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_mvm_sar_get_ewrd_table() In case of a BIOS bug, n_profiles
might be 0 thus we need to return an error value. Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Delete the scanned channel results.
No need in it we get it any way when logging.
The print only clogs up the ftrace print buffer.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While freeing inactive queue, check mvmsta to be valid before
dereferencing it. Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to have iwl_run_unified_mvm_ucode() be exposed
to other parts of the code since the logic to pick it over the
normal code in iwl_run_init_mvm_ucode() can just be done in
that function itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rates were changed to adapt to HE. Change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+cipAAoJEG4XJFUm622b+04H/2u7zhIqv3R5NsmGRlwjKmvd
6us1hcYzUiBW1kBFFtcvokwgqv3Rw/EUi+NYA5UCHgo30HTVJWTqW0q+BUEI7U0X
iwuFdHbs/qjj8hXKgZwaJMVyRhXAbq+iHYaMY5OEDNTRSbxqXA4V69SHGK9vLX0l
KQLJBZX3etnwsyRWrmd4E0roGGfD5tMPpGMUDSlvTPWt0I+1QFUxRI9ohn1fRBpD
p+UHHC+SYF6NzxvfqyPwm6ndb2XOwdAKYljlf4KrBwHtSXvAH8p5EASm4PjGbavY
0mrkv0cb8QOKQNVe9q4B4AmM4iAITZ9i3sQBPJ+EBN2P+kS/lFU5L/+5z3VQjms=
=KTEG
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When FW fails to get block ack, it will send the notification with
0 items in the TFD queue elements. Allow this and handle accordingly.
Fixes: c46e7724bf ("iwlwifi: mvm: support new BA notification response")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 CDB firmware, we cannot update phy context to a
different band - we must first remove it and add it
again. Support this flow for all a000 devices since
we may have various combinations that cause us to fail
regardless if CDB is active.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently when rate isn't found (invalid rate or CCK rate in high
band) driver is assigning rate -1, which causes mac80211 to dump
it later with the cryptic rate value of 0xFF.
Instead, warn early and dump the frame in mvm.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 devices, we don't really have multi RX queue for now,
until we have the RX queue configuration API.
Disable RX queue notification for now.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we load firmware in extended mode (as we do by default for
now) driver should send a command what kind of commands ucode
should stop and wait for before proceeding with phy calibrations.
Support this command. Currently we only do NVM access - so mark
this bit only.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To utilize the maximum allowed tx power, an additional table was added
to the BIOS. The table consists of up to seven different regions
(currently only three are in use). Each region contains per band:
1. Maximum allowed tx power on the band.
2. Tx power offset for chain A.
3. Tx power offset for chain B.
On init flow driver reads this table by means of ACPI and
passes it to the firmware with GEO_TX_POWER_LIMIT cmd.
The firmware will use this table to enhance tx power with
the offset in the relevant table as well as verifying it does not
violate the maximum allowed tx power.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
API was changed once more to support 2 LMACs.
Adapt to change while preserving current functionality.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the end, the firmware doesn't want the SP len as present
in the WMM IE, but rather the actual number of frames.
Fixes: bd3c6cf901a8 ("iwlwifi: mvm: tell the firmware about the U-APSD parameters")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get SN that is smaller than SSN of the aggregation,
we shouldn't apply any reordering on them.
Further more, HW NSSN will be zeroed, which can cause us
to make some invalid decisions.
Detect the situation and invalidate the BAID.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change the value of TX_CMD_SEC_KEY_FROM_TABLE flag
in TX_CMD security flags to accommodate a FW API change.
Bump min API for 9000 series devices to 30 to keep the driver aligned
aligned the FW.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Seems like HW is reversing addr3 in the MAC header of de-aggregated
AMSDU. Reverse it back.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This flag is used for mac80211 reordering. As we do reordering
ourselves, turning it on is misleading and pointless.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Not only that this write is not needed (as FW does this
itself), on newer HW this register is write protected
so trying to write there will cause problems.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In TVQM firmware returns the value of the queue ID and code
should accept it.
The TX queue config API was changed. Move to new API.
This has to be done in parallel in mvm and pcie.
Do not move yet to 512 queues since there are some opens
with enabling it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In TVQM mode the TX responses were changed to include
queue number since legacy TX queue number retrieval cannot
be scaled up to 512 queues.
Support this change.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
By moving all the code that depends on the new API
we avoid unnecessary indentation in the code.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer firmware versions will be able to handle all the
WMM-PS flows internally when we act as a GO. The firwmare
relies on the fact that the drivers puts frames for
different peers in different queues (DQA) to achieve this.
The driver will not be aware of the power state of the peers
anymore.
Tell the firmware about the WMM-PS parameters of earch peer
that connects to us so that it can know what are the
trigger-enabled ACs, the delivery-enableds ACs and the
Service Period length.
This API change is backward compatible since older firmware
versions will simply ignore the newly added values.
Since we don't support ieee80211 TSPECs for now, just copy
the trigger-enabled ACs to the delivery enabled ones.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
