Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.
To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses incorrect APIs to unmap DMA memory which were
mapped using dma_map_single(). This patch fixes it to use
appropriate APIs for un-mapping DMA memory.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed_dcbx_query_params() implementation populate the values to input
buffer based on the dcbx mode and, the current negotiated state/params,
the caller of this API need to memset the buffer to zero.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx indirection table entries are in the range [0, (rss_count - 1)]. If
user reduces the rss count, the table entries may not be in the ccorrect
range. Need to reconfigure the table with new rss_count as a basis.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the current default values for Rx path i.e., 8 queues of 8Kb entries
each with 4Kb size, interface will consume 256Mb for Rx. The default values
causing the driver probe to fail when the system memory is low. Based on
the perforamnce results, rx-ring count value of 1Kb gives the comparable
performance with Rx coalesce timeout of 12 seconds. Updating the default
values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the execution of loopback test, driver may receive the packets which
are not originated by this test, loopback implementation need to skip those
packets.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS configuration is not supported for 100G adapters.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes in kernel ethtool implementation requires the driver
callback for get_channels() has to populate the values for max tx/rx
coalesce fields.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory return by kzalloc() has already be set to zero, so
remove useless memset(0).
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qede: min_mtu 46, max_mtu 9600
- Put define for max in qede.h
qlcnic: min_mtu 68, max_mtu 9600
CC: netdev@vger.kernel.org
CC Dept-GELinuxNICDev@qlogic.com
CC: Yuval Mintz <Yuval.Mintz@qlogic.com>
CC: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a skeletal implementation of the qed* RoCE driver -
basically the ability to communicate with the qede driver and
receive notifications from it regarding various init/exit events.
Signed-off-by: Rajesh Borundia <rajesh.borundia@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
While handling SPQ ramrod completion, there is a possible race
where driver might not read updated fw return code based on
ramrod completion done. This patch ensures that fw return code
is written first and then completion done flag is updated
using appropriate memory barriers.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Malicious VFs might be caught in several different methods:
- Misusing their bar permission and being blocked by hardware.
- Misusing their fastpath logic and being blocked by firmware.
- Misusing their interaction with their PF via hw-channel,
and being blocked by PF driver.
On the first two items, firmware would indicate to driver that
the VF is to be considered malicious, but would sometime still
allow the VF to communicate with the PF [depending on the exact
nature of the malicious activity done by the VF].
The current existing logic on the PF side lacks handling of such events,
and might allow the PF to perform some incorrect configuration on behalf
of a VF that was previously indicated as malicious.
The new scheme is simple -
Once the PF determines a VF is malicious it would:
a. Ignore any further requests on behalf of the VF-driver.
b. Prevent any configurations initiated by the hyperuser for
the malicious VF, as firmware isn't willing to serve such.
The malicious indication would be cleared upon the VF flr,
after which it would become usable once again.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a ramrod is being sent for some device configuration,
the driver is going to sleep at least 5ms between each iteration
of polling on the completion of the ramrod.
However, in almost every configuration scenario the firmware
would be able to comply and complete the ramrod in a manner of
several usecs. This is especially important in cases where there
might be a lot of sequential configurations applying to the hardware
[e.g., RoCE], in which case the existing scheme might cause some
visible user delays.
This patch changes the completion scheme - instead of immediately
starting to sleep for a 'long' period, allow the device to quickly
poll on the first iteration after a couple of usecs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently qede fails to set IFF_UNICAST_FLT, and as a result is not
actually performing unicast MAC filtering.
While we're at it - relax a hard-coded limitation that limits each
interface into using at most 15 unicast MAC addresses before turning
promiscuous. Instead utilize the HW resources to their limit.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to hardware limitation, when transmitting a geneve-encapsulated
packet with more than 32 bytes worth of geneve options the hardware
would not be able to crack the packet and consider it a regular UDP
packet.
This implements the ndo_features_check() in qede in order to prevent
GSO on said transmitted packets.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GSO support for GRE and UDP tunnels
where outer checksums are enabled.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hypervisors can support MAC hints to their VFs.
Even though we don't have such a hypervisor API in linux, we add
sufficient logic for the VF to be able to receive such hints and
set the mac accordingly - as long as the VF has not been set with
a MAC already.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans many of the warnings that would arise in qed as a
result of compilations with C=1; Most of those are the addition
of missing 'static' to functions, although there are several other
fixes as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qedr driver would require a tristate Kconfig option [to allow
it to compile as a module], and toward that end we've added the
INFINIBAND_QEDR option. But as we've made the compilation of the
qed/qede infrastructure required for RoCE dependent on the option
we'd be facing linking difficulties in case that QED=y or QEDE=y,
and INFINIBAND_QEDR=m.
To resolve this, we seperate between the INFINIBAND_QEDR option
and the infrastructure support in qed/qede by introducing a new
QED_RDMA option which would be selected by INFINIBAND_QEDR but would
be a boolean instead of a tristate; Following that, the qed/qede is
fixed based on this new option so that all config combinations would
be supported.
Fixes: cee9fbd8e2 ("qede: add qedr framework")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch compains about qed_roce_ll2_tx() dereference
of the 'cdev' variable while testing its validity later.
As the validation checking is an over-kill [variable would always
be set], simply remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: abd49676c7 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of qed_get_rdma_ops() is not a prototype unless
we add 'void' here, as indicated by this W=1 warning:
drivers/net/ethernet/qlogic/qed/qed_roce.c: In function ‘qed_get_rdma_ops’:
drivers/net/ethernet/qlogic/qed/qed_roce.c:2950:28: error: old-style function definition [-Werror=old-style-definition]
Fixes: abd49676c7 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each_entry() macro aptly named
list_for_each_entry_safe().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the RoCE-specific LL2 logic [as well as GSI support] over
the 'generic' LL2 interface.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add slowpath configuration support for user, dma and memory
regions registration.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the slowpath configurations of Queue Pair verbs
which adds, deletes, modifies and queries Queue Pairs.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the configurations of the protection domain and
completion queues.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the backbone required for the various HW initalizations
which are necessary for the qedr driver - FW notification, resource
initializations, etc.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a skeletal implementation of the qede RoCE driver -
The qedr has some dependencies of the state of the underlying base
interface. This adds some logic required with mutual registrations
and the ability to pass updates on 'intresting' events.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other protocols beside the networking driver need the ability
of passing some L2 traffic, usually [although not limited] for the
purpose of some management traffic.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fe56b9e6a8 ("qed: Add module with basic common support")
has introduced a stack corruption during probe, where filling a
local struct with data to be sent to management firmware is incorrectly
filled; The data is written outside of the struct and corrupts
the stack.
Changes from v1:
----------------
- Correct the value written [Caught by David Laight]
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a few warnings when building kernel with W=1:
drivers/net/ethernet/qlogic/qed/qed_l2.c:112:5: warning: no previous prototype for 'qed_sp_vport_start' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:110:6: warning: no previous prototype for 'qed_iov_is_valid_vfid' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:188:5: warning: no previous prototype for 'qed_iov_post_vf_bulletin' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:578:6: warning: no previous prototype for 'qed_iov_set_vfs_to_disable' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:1135:28: warning: no previous prototype for 'qed_iov_get_public_vf_info' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:1148:6: warning: no previous prototype for 'qed_iov_clean_vf' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:2444:5: warning: no previous prototype for 'qed_iov_chk_ucast' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:2762:5: warning: no previous prototype for 'qed_iov_vf_flr_cleanup' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/qlogic/qede/qede_main.c:2113:5: warning: no previous prototype for 'qede_set_features' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for dumping and formatting the HW/FW debug data.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 4 warnings when building kernel with W=1:
drivers/net/ethernet/qlogic/qed/qed_selftest.c:6:5: warning: no previous prototype for 'qed_selftest_memory' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:19:5: warning: no previous prototype for 'qed_selftest_interrupt' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:32:5: warning: no previous prototype for 'qed_selftest_register' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:55:5: warning: no previous prototype for 'qed_selftest_clock' [-Wmissing-prototypes]
In fact, these functions are declared in qed_selftest.h, so this patch
add missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for several infrastructure operations that are done as part of
debug data collection.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These messages are unnecessary as OOM allocation failures already do
a dump_stack() giving more or less the same information.
$ size drivers/net/ethernet/qlogic/qed/built-in.o* (defconfig x86-64)
text data bss dec hex filename
127817 27969 32800 188586 2e0aa drivers/net/ethernet/qlogic/qed/built-in.o.new
132474 27969 32800 193243 2f2db drivers/net/ethernet/qlogic/qed/built-in.o.old
Miscellanea:
o Change allocs to the generally preferred forms where possible.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fdb dumps spanning multiple skb's currently restart from the first
interface again for every skb. This results in unnecessary
iterations on the already visited interfaces and their fdb
entries. In large scale setups, we have seen this to slow
down fdb dumps considerably. On a system with 30k macs we
see fdb dumps spanning across more than 300 skbs.
To fix the problem, this patch replaces the existing single fdb
marker with three markers: netdev hash entries, netdevs and fdb
index to continue where we left off instead of restarting from the
first netdev. This is consistent with link dumps.
In the process of fixing the performance issue, this patch also
re-implements fix done by
commit 472681d57a ("net: ndo_fdb_dump should report -EMSGSIZE to rtnl_fdb_dump")
(with an internal fix from Wilson Kok) in the following ways:
- change ndo_fdb_dump handlers to return error code instead
of the last fdb index
- use cb->args strictly for dump frag markers and not error codes.
This is consistent with other dump functions.
Below results were taken on a system with 1000 netdevs
and 35085 fdb entries:
before patch:
$time bridge fdb show | wc -l
15065
real 1m11.791s
user 0m0.070s
sys 1m8.395s
(existing code does not return all macs)
after patch:
$time bridge fdb show | wc -l
35085
real 0m2.017s
user 0m0.113s
sys 0m1.942s
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:1230:13-20: WARNING: kzalloc should be used for dcbx_info, instead of kmalloc/memset
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:1192:13-20: WARNING: kzalloc should be used for dcbx_info, instead of kmalloc/memset
Use kzalloc rather than kmalloc followed by memset with 0
This considers some simple cases that are common and easy to validate
Note in particular that there are no ...s in the rule, so all of the
matched code has to be contiguous
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
CC: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes care of clearing the uninitialized buffer before using it.
1. pfc pri-enable bitmap need to be cleared before setting the requested
enable bits. Without this, the un-touched values will be merged with
requested values and sent to MFW.
2. The data in app-entry field need to be cleared before using it.
3. Clear the output data buffer used in qed_dcbx_query_params().
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware requires the selection-field (SF) to be set for
configuring the application/protocol entry in IEEE mode. Without this
setting, the app entry will be configured incorrectly in MFW.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dcbx configuration is not supported for VF interfaces. Hence don't populate
the callbacks for VFs and also fail the dcbx-query for VFs.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of the per-queue statistics introduced a harmless warning
on all 32-bit architectures:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function 'qede_get_ethtool_stats':
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
buf[cnt++] = QEDE_TQSTATS_DATA(edev,
^
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:22: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
buf[cnt++] = QEDE_TQSTATS_DATA(edev,
^
This changes the cast to 'void *' to shut up the warning, which
avoids the assumptions on the size of the pointer type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 68db9ec2df ("qede: Add support for per-queue stats.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add provision for configuring the fastpath queues with Tx (or Rx) only
functionality.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each VF employees a lock that's supposed to serialize its usage of the
HW channel for communication with its PF, but the critical section is
ill-defined:
- VFs currently release the lock whenever the PF response arrives,
prior to actually processing the reply buffer [which was also supposed
to have been protected by same lock].
- The lock would be released on first response, ignoring the possibilty
the sw flow isn't over [as might be the case of the acquisition flow].
As a result, the flow would run unprotected and would cause a double
mutex release [as the additional message completion would release it
while its actually already free].
Change the flow to have a dedicated function to be called at end of each
flow and release the lock.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern VFs can't run on old non-compatible as the fastpath HSI is
slightly changed - but as the HSI is actually very close [basically,
a single bit whose meaning flipped] this can be supported with small
modifications.
The major differences would be in:
- Recognizing that VF is running on top of a legacy PF.
- Returning some slowpath configurations that are no longer needed
on top of modern PFs, but would be required when working over
the legacy ones.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware would silently drop any control frame sent by VF to prevent
a malicious VF from generating pause flood in the network.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8.10.x FW added support for forward compatability as well as
'future' backward compatibility, but only to those VFs that were
using HSI which was 8.10.x based or newer.
The latest firmware now supports backward compatibility for the
older VFs based on 8.7.x and 8.8.x firmware as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver never bothered marking the VF's vport with the VF's sw_fid.
As a result, FLR flows are not going to clean those vports.
If the vport was active when FLRed, re-activating it would lead
to a FW assertion.
Fixes: dacd88d6f6 ("qed: IOV l2 functionality")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware for the qed* adpaters fixes several issues:
- Better blocking of malicious VFs.
- After FLR, Tx-switching [internal routing] of packets might
be incorrect.
- Deletion of unicast MAC filters would sometime have side-effect
of corrupting the MAC filters configred for a device.
It also contains fixes for future qed* drivers that *hopefully* would be
sent for review in the near future.
In addition, it would allow driver some new functionality, including:
- Allowing PF/VF driver compaitibility with old drivers [running
pre-8.10.5.0 firmware].
- Better debug facilities.
This would also bump the qed* driver versions to 8.10.9.20.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While '0xdead' and '0xbeef' are "great" values, we should
use the correct SPEED_* values instead.
Fixes: 054c67d1c8 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When moving into using ethtool's link_ksetting, qed started
supplying its own bitmask of speed/capabilities, but qede
is still checking for the SUPPORTED value to determine whether
it supports pause.
Fixes: 054c67d1c8 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses netif_tx_queue_stopped() to make sure the xmit_more
indication will be honored, but that only checks for DRV_XOFF.
At the same time, it's possible that during transmission the DQL will
close the transmission queue with STACK_XOFF indication.
In re-configuration flows, when the threshold is relatively low, it's
possible that the device has no pending tranmissions, and during
tranmission the driver would miss doorbelling the HW.
Since there are no pending transmission, there will never be a Tx
completion [and thus the DQL would not remove the STACK_XOFF indication],
eventually causing the Tx queue to timeout.
While we're at it - also doorbell in case driver has to close the
transmission queue on its own [although this one is less important -
if the ring is full, we're bound to receive completion eventually,
which means the doorbell would only be postponed and not indefinetly
blocked].
Fixes: 312e06761c ("qede: Utilize xmit_more")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for sending the NCSI statistics to the
MFW. This is an asynchronous request from MFW. Upon receiving this, driver
populates the required data and send it to MFW.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for capturing stats ttl0_discard and
packet_too_big_discard in "ethtool -S" display.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch touches various prints in the driver - it reduces the
verbosity of some prints [which were previously logged by default]
while adding several new debug prints and modifying others.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change qed* code in trivial manner; This isn't necessarily
semantic-only, but the end result is the same, i.e., no change
should occur from user perspective. Changes include:
- Using temporary variables to better fit 80-character restrictions.
- Removal of unused variables & code with no effect.
[plus some additional minor modifications].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make semantic-only adjustments to qed* drivers, such as:
- Changes in code indentation.
- Usage of BIT() macro.
- re-naming of variables.
- Re-ordering of variable declerations.
- Removal of (== 0) and (!= 0) in conditions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'dcbx_info is malloced in qed_dcbnl_get_ieee_pfc() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: a1d8d8a51e ("qed: Add dcbnl support.")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver implementation for ethtool link_ksettings
callbacks. qed driver now defines/uses the qed specific masks for
representing link capability values. qede driver maps these values to
to new link modes defined by the kernel implementation of link_ksettings.
Please consider applying this to 'net-next' branch.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
App count is not updated while adding new app entry to the dcbx app table.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW now supports the Selection field for IEEE mode. Add driver changes to
use the newer MFW masks to read/write the port-id value.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtype value is being read incorrectly in ieee-dcbx mode. Use the
correct mfw mask value.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Endian-ness conversion is not needed for priority-to-TC field as the
field is already being read/written by the driver in big-endian way.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver modifies the supplied NAPI budget in qlcnic_83xx_msix_tx_poll()
function. Instead, it should use the budget as it is.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a data structure corruption bug in the SRIOV VF mailbox
handler code. While handling mailbox commands from the atomic context,
driver is accessing and updating qlcnic_async_work_list_struct entry fields
in the async work list. These fields could be concurrently accessed by the
work function resulting in data corruption.
This patch restructures async mbx command handling by using a separate
async command list instead of using a list of work_struct structures.
A single work_struct is used to schedule and handle the async commands
with proper locking mechanism.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
100g support is not available in MSI mode. Failing the driver load in this scenario.
Please consider applying this to `net'.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -EINVAL instead of 0 when EQ elements is
too larger, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assigning NULL to parmeter dcb has no effect outside of the
inlined function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not write random bytes from the kernel stack when
calling qed_wr.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable length is not used after the deleted line.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each PF/VF has a limited number of vlan filters for
configuration purposes; This information is passed to qede
and is used to prevent over-usage - once a vlan is to be
configured and no filter credit is available, the driver
would switch into working in vlan-promisc mode.
Problem is the credit pool is shared by both PFs and VFs,
and currently PFs aren't deducting the filters that are
reserved for their VFs from their quota, which may lead
to some vlan filters failing unknowingly due to lack of credit.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses reverse logic when checking if minimum
bandwidth configuration applied, causing it to
configure the guarantee only on the first hw-function.
Fixes: a0d26d5a4f ("qed*: Don't reset statistics on inner reload")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the necessary logic to prevet statistics reset
on inner-reload introduced a bug, and now statistics
are reset only when re-probing the driver.
Fixes: a0d26d5a4f ("qed*: Don't reset statistics on inner reload")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before requesting the firmware to start Rx queues,
driver goes and sets the queue producer in the device to 0.
But while the producer is 32-bit, the driver currently clears 64 bits,
effectively zeroing an additional CID's producer as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver has reverse logic for checking the result of the
spoof-checking configuration. As a result, it would log that
the configuration failed [even though it succeeded], and will
no longer do anything when requested to remove the configuration,
as it's accounting of the feature will be incorrect.
Fixes: 6ddc760825 ("qed*: IOV support spoof-checking")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of ndo_vlan_rx_kill_vid() implementation,
qede is requesting firmware to remove the vlan filter.
This currently happens even if the vlan wasn't previously
added [In case device ran out of vlan credits].
For PFs this doesn't cause any issues as the firmware
would simply ignore the removal request. But for VFs their
parent PF is holding an accounting of the configured vlans,
and such a request would cause the PF to fail the VF's
removal request.
Simply fix this for both PFs & VFs and don't remove filters
that were not previously added.
Fixes: 7c1bfcad9f ("qede: Add vlan filtering offload support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slowpath completion handling is incorrectly changing
SPQ_RING_SIZE bits instead of a single one.
Fixes: 76a9a3642a ("qed: fix handling of concurrent ramrods")
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses xmit_more optimization to reduce
number of TX doorbells write per packet.
Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleanups qede_poll() routine a bit
and allows qede_poll() to do single iteration to handle
TX completion [As under heavy TX load qede_poll() might
run for indefinite time in the while(1) loop for TX
completion processing and cause CPU stuck].
Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling IP fragmented packets with csum in their
transport header, the csum isn't changed as part of the
fragmentation. As a result, the packet containing the
transport headers would have the correct csum of the original
packet, but one that mismatches the actual packet that
passes on the wire. As a result, on receive path HW would
give an indication that the packet has incorrect csum,
which would cause qede to discard the incoming packet.
Since HW also delivers a notification of IP fragments,
change driver behavior to pass such incoming packets
to stack and let it make the decision whether it needs
to be dropped.
Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call wmb() to ensure writes are complete before
hardware fetches updated Tx descriptors.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
SPQ doorbell is currently protected with the compilation barrier. Under the
stress scenarios, we may get into a state where (due to the weak ordering)
several ramrod doorbells were written to the BAR with an out-of-order
producer values. Need to change the barrier type to a write barrier to make
sure that the write buffer is flushed after each doorbell.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static checker warnings:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:435 qede_get_coalesce()
warn: passing casted pointer '&coal->rx_coalesce_usecs' to
'edev->ops->common->get_coalesce()' 32 vs 16.
The u32 pointer is being typecasted to u16 which may fail for big-endian
platforms.
Fixes: d552fa84cb ("qede: Add support for coalescing config read/update.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a static checker warning here "warn: mask and shift to zero"
and the code sets "ring" to zero every time. From looking at how
QLCNIC_FETCH_RING_ID() is used in qlcnic_83xx_process_rcv_ring() the
qlcnic_83xx_hndl() should be removed.
Fixes: 4be41e92f7 ('qlcnic: 83xx data path routines')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring the device tx/rx coalescing
timeout values in the order of micro seconds. It also adds APIs for
upper layer drivers for reading/updating the coalescing values.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'MODULE_FIBER' value replaced several other FIBER values
in newer management firmware images, so existing code would
fail to properly reflect its mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver has 2 sets of entries for handling ramrod configurations
toward firmware - a regular pre-allocated set of entires and a
possible 'unlimited' list of additional pending entries.
In most scenarios the 'unlimited' list would not be used, but
when it does the handling of the ramrod completion doesn't
properly handle the release of the entry.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several user APIs can cause driver to perform an inner-reload.
Currently, doing this would cause the HW/FW statistics of the
adapter to reset, which isn't the expected behavior [statistics
should only reset on explicit unloads].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal loopback in driver is based on two things - first
is the willingness of transmitter to use it [in case of VFs,
this can be forced based on VEPA/VEB] and secondly on another
vport classification configuration which should match the
packet's destination.
Current code allows non-linux VFs to configure a 'promisc'
mode on Tx, meaning all traffic sent by VF would be loopbacked
internally by firmware; This isn't considered a valid mode and
as such should be prevented by PF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no vlan filter is configured, firmware has a configurable
default on whether to pass only untagged packets or all packets
regardless of their tagging. Driver currently doesn't set this
field in the necessary ramrod, causing the default to always be
'receive all'.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a warning for qlcnic_83xx_get_mac_address when building with
"make W=1":
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c: In function 'qlcnic_83xx_get_mac_address':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:2156:8: error: parameter 'function' set but not used [-Werror=unused-but-set-parameter]
Clearly this is harmless, but there is also no point for setting
the variable, so we can simply remove the assignment.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the interfaces for ieee/cee dcbnl callbacks and registers
them with the kernel.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the implementation for both cee/ieee dcbnl callbacks by
using the qed query/config APIs.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query API reads the dcbx data from the device shared memory and return it
to the caller. The config API configures the user provided dcbx values on
the device, and initiates the dcbx negotiation with the peer.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code "ent_per_page" could be more than "conn_num" making
"conn_num" negative after the subtraction. In the next iteration
through the loop then the negative is treated as a very high positive
meaning we don't put a limit on "ent_num". It could lead to memory
corruption.
Fixes: dbb799c397 ('qed: Initialize hardware for new protocols')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a future VF would send the PF an unknown message, the PF today would
not send a reply. This would have 2 bad effects:
a. VF would have to timeout on the request.
b. If VF were to send an additional message to PF, firmware would mark
it as malicious.
Instead, if there's some valid reply-address on the message - let the PF
answer and tell the VF it doesn't know the message.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only limitation relating to MACs the PF enforce today on its VFs
is in case it has a forced-unicast MAC address for them, in which case
they can't configure other unicast addresses.
Specifically, the PF isn't enforcing the number of MAC addresse a VF can
configure regardless of the nubmer of such filters agreed upon by PF and
VF during the acquisition process.
PF's shadow-config is now extended to also contain information about its
VFs' unicast addresses configuration, allowing such enforcement.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, the VF is aware of its queues context-ids, and calculates the
doorbell address when opening its queues on its own.
The configuration of doorbells in HW can sometime in the future be changed
by the PF [hw has several configurable features that might affect doorbell
addresses, e.g., dpm support], this would break compatibility with older
VFs as their calculated doorbell addresses would be incorrect for such a
configuration.
In order to avoid such a backward compatibility failure, let the PF make
the calculation of the doorbell offset based on the context-id, and pass
that to the VF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several requests the VF can make toward the PF which the driver
would pass to firmware without checking the validity first - specifically,
opening queues and updating vports. Such configurations might cause the
firmware to assert.
This adds validation of the legality of said configurations on the PF side
before passing it onward via ramrod to firmware.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the goals of the vf's first message to the PF [acquire]
is to learn about the number of resources available to it [macs, vlans,
etc.]. This is done via negotiation - the VF requires a set of resources,
which the PF either approves or disaproves and sends a smaller set of
resources as alternative. In this later case, the VF is then expected to
either abort the probe or re-send the acquire message with less
required resources.
While this infrastructure exists since the initial submision of qed
SRIOV support, it's in fact completely inoperational - PF isn't really
looking into the resources the VF has asked for and is never going to
reply to the VF that it lacks resources.
This patch addresses this flow, fixing it and allowing the PF and VF
to actually agree on a set of resources.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver require an exact match between VF and PF storm firmware;
Any difference would fail the VF acquire message, causing the VF probe
to be aborted.
While there's still dependencies between the two, the recent FW submission
has relaxed the match requirement - instead of an exact match, there's now
a 'fastpath' HSI major/minor scheme, where VFs and PFs that match in their
major number can co-exist even if their minor is different.
In order to accomadate this change some changes in the vf-start init flow
had to be made, as the VF start ramrod now has to be sent only after PF
learns which fastpath HSI its VF is requiring.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RoCE and iSCSI would require some added/changed hw configuration in order
to properly run; The biggest single change being the requirement of
allocating and mapping host memory for several HW blocks that aren't being
used by qede [SRC, QM, TM, etc.].
In addition, whereas qede is only using context memory for HW blocks, the
new protocol would also require task memories to be added.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds in the ecore 2 new personalities in addition to
QED_PCI_ETH - QED_PCI_ISCSI and QED_PCI_ETH_ROCE.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the qed portion of the RoCE & iSCSI firmware HSI,
as well as adding several new common HSI files which would be required
by both qed and qed* protocols.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RoCE driver is going to need a 32-bit chain [current chain implementation
for qed* currently supports only 16-bit producer/consumer chains].
This patch adds said support, as well as doing other slight tweaks and
modifications to qed's chain API.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The New QED firmware contains several fixes, including:
- Wrong classification of packets in 4-port devices.
- Anti-spoof interoperability with encapsulated packets.
- Tx-switching of encapsulated packets.
It also slightly improves Tx performance of the device.
In addition, this firmware contains the necessary logic for
supporting iscsi & rdma, for which we plan on pushing protocol
drivers in the imminent future.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warns about qed_fill_link possibly accessing uninitialized data:
drivers/net/ethernet/qlogic/qed/qed_main.c: In function 'qed_fill_link':
drivers/net/ethernet/qlogic/qed/qed_main.c:1170:35: error: 'link_caps' may be used uninitialized in this function [-Werror=maybe-uninitialized]
While this warning is only about the specific case of CONFIG_QED_SRIOV
being disabled but the function getting called for a VF (which should
never happen), another possibility is that qed_mcp_get_*() fails without
returning data.
This rearranges the code so we bail out in either of the two cases
and print a warning instead of accessing the uninitialized data.
The qed_link_output structure remains untouched in this case, but
all callers first call memset() on it, so at least we are not leaking
stack data then.
As discussed, we also use a compile-time check to ensure we never
use any of the VF code if CONFIG_QED_SRIOV is disabled, and the
PCI device table is updated to no longer bind to virtual functions
in that configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently 100g devices don't support minimum/maximum BW configurations,
yet link flaps might cause the driver to attempt to do such a
configuration. Prevent this just as we do for the maximum BW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapter can support 100g in both MSIx and INTa, but not in MSI.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the HW configurations are currently missing for 100g devices.
This can cause various classification issues, as well as prevent device
from fully reaching line-rate.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DCBx re-negotiation is occurring, the PF's configurations for
maximum and minimum bandwidth guarantees are currently lost.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 39651abd28 ("qed: add support for dcbx") is re-configuring
the QM hw-block as part of its sequence. This is done in attention
handling context which is non-sleepable, yet memory is allocated in
this flow using GFP_KERNEL.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PFs and VFs differ in their registered ethtool operations,
but they're using a common function for get_sset_count().
As a result, `ethtool -i' for a VF would indicate it supports
selftest, although that's not the case.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since driver is using a FW-based GRO implementation, this has some
effects on its ability to cope with GRO enablement/disablement.
As a result, driver must perform an inner-reload as a result of a state
change in the offload configuration of said feature.
[Failure to do so means network stack would continue to receive
aggregated packets even though user requested the feature to be disabled].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF is currently ignoring the minimum provided by the API,
mistakenly using the maximum for minimum as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the coding error in determining the enable flag for
the application/protocol. The enable flag should be set for all protocols
but the eth.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One timer, whose handler keeps reading on MMIO register for EEH
core to detect error in time, is started when the PCI device driver
is loaded. MMIO register can't be accessed during PE reset in EEH
recovery. Otherwise, the unexpected recursive error is triggered.
The timer isn't closed that time if the interface isn't brought
up. So the unexpected recursive error is seen during EEH recovery
when the interface is down.
This avoids the unexpected recursive EEH error by closing the timer
in qlge_io_error_detected() before EEH PE reset unconditionally. The
timer is started unconditionally after EEH PE reset in qlge_io_resume().
Also, the timer should be closed unconditionally when the device is
removed from the system permanently in qlge_io_error_detected().
Reported-by: Shriya R. Kulkarni <shriyakul@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"priority" needs to be signed for the error handling to work.
Fixes: 39651abd28 ('qed: add support for dcbx.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes and more updates from David Miller:
1) Tunneling fixes from Tom Herbert and Alexander Duyck.
2) AF_UNIX updates some struct sock bit fields with the socket lock,
whereas setsockopt() sets overlapping ones with locking. Seperate
out the synchronized vs. the AF_UNIX unsynchronized ones to avoid
corruption. From Andrey Ryabinin.
3) Mount BPF filesystem with mount_nodev rather than mount_ns, from
Eric Biederman.
4) A couple kmemdup conversions, from Muhammad Falak R Wani.
5) BPF verifier fixes from Alexei Starovoitov.
6) Don't let tunneled UDP packets get stuck in socket queues, if
something goes wrong during the encapsulation just drop the packet
rather than signalling an error up the call stack. From Hannes
Frederic Sowa.
7) SKB ref after free in batman-adv, from Florian Westphal.
8) TCP iSCSI, ocfs2, rds, and tipc have to disable BH in it's TCP
callbacks since the TCP stack runs pre-emptibly now. From Eric
Dumazet.
9) Fix crash in fixed_phy_add, from Rabin Vincent.
10) Fix length checks in xen-netback, from Paul Durrant.
11) Fix mixup in KEY vs KEYID macsec attributes, from Sabrina Dubroca.
12) RDS connection spamming bug fixes from Sowmini Varadhan
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
net: suppress warnings on dev_alloc_skb
uapi glibc compat: fix compilation when !__USE_MISC in glibc
udp: prevent skbs lingering in tunnel socket queues
bpf: teach verifier to recognize imm += ptr pattern
bpf: support decreasing order in direct packet access
net: usb: ch9200: use kmemdup
ps3_gelic: use kmemdup
net:liquidio: use kmemdup
bpf: Use mount_nodev not mount_ns to mount the bpf filesystem
net: cdc_ncm: update datagram size after changing mtu
tuntap: correctly wake up process during uninit
intel: Add support for IPv6 IP-in-IP offload
ip6_gre: Do not allow segmentation offloads GRE_CSUM is enabled with FOU/GUE
RDS: TCP: Avoid rds connection churn from rogue SYNs
RDS: TCP: rds_tcp_accept_worker() must exit gracefully when terminating rds-tcp
net: sock: move ->sk_shutdown out of bitfields.
ipv6: Don't reset inner headers in ip6_tnl_xmit
ip4ip6: Support for GSO/GRO
ip6ip6: Support for GSO/GRO
ipv6: Set features for IPv6 tunnels
...
Driver incorrectly uses dma_unmap_addr_set() to set
a variable which is in truth a dma_addr_t
[i.e not defined using DEFINE_DMA_UNMAP_ADDR()] and is
being used by the driver flows other than unmapping
physical addresses. This patch fixes driver fastpath
where CONFIG_NEED_DMA_MAP_STATE is not set.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many developers already know that field for reference count of the
struct page is _count and atomic type. They would try to handle it
directly and this could break the purpose of page reference count
tracepoint. To prevent direct _count modification, this patch rename it
to _refcount and add warning message on the code. After that, developer
who need to handle reference count will find that field should not be
accessed directly.
[akpm@linux-foundation.org: fix comments, per Vlastimil]
[akpm@linux-foundation.org: Documentation/vm/transhuge.txt too]
[sfr@canb.auug.org.au: sync ethernet driver changes]
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Yuval Mintz <yuval.mintz@qlogic.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page_reference manipulation functions are introduced to track down
reference count change of the page. Use it instead of direct
modification of _count.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the necessary driver support for Management Firmware to
configure the device/firmware with the dcbx results. Management Firmware
is responsible for communicating the DCBX and driving the negotiation,
but the driver has responsibility of receiving async notification and
configuring the results in hw/fw. This patch also adds the dcbx support for
future protocols (e.g., FCoE) as preparation to their imminent submission.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This line was indented more than it should be.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF's probe might log that it has no PM capability in its PCI configuration
space. As this is a valid configuration, silence such prints.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-function modes, PFs are currently limited to using 16 VFs -
But that limitation would also currently apply in case there's a single
PCI function exposed, where no such restriction should have existed.
This lifts the restriction for the default mode; User should be able
to start the maximum number of VFs as appear in the PCI config space.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF updates its VFs' bulletin boards with link configurations whenever
the physical carrier changes or whenever hyper-user explicitly requires
some setting of the VFs link via the hypervisor's PF.
Since the bulletin board is getting cleaned as part of the IOV disable
flow on the PF side, re-enabling sriov would lead to a VF that sees the
carrier as 'down', until an event causing the PF to re-fill the bulletin
with the link configuration would occur.
To fix this we simply refelect the link state during the flows, giving
the later VFs a default reflecting the PFs link state.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During FLR flow, need to make sure HW is no longer capable of writing to
host memory as part of its interrupt mechanisms.
While we're at it, unify the logic cleaning the driver's status-blocks
into using a single API function for both PFs and VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems like something broke in commit 1408cc1fa4 ("qed: Introduce VFs")
and the function no longer verifies that the vf is indeed a valid one.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Device should be configured by default to VEB once VFs are active.
This changes the configuration of both PFs' and VFs' vports into enabling
tx-switching once sriov is enabled.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the user to view the VF configuration by observing the PF's
device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in `ndo_set_vf_spoofchk' for allowing PF control over
its VF spoof-checking configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support in 2 ndo that allow PF to tweak the VF's view of the
link - `ndo_set_vf_link_state' to allow it a view independent of the PF's,
and `ndo_set_vf_rate' which would allow the PF to limit the VF speed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the PF to enforce the VF's mac.
i.e., by using `ip link ... vf <x> mac <value>'.
While a MAC is forced, PF would prevent the VF from configuring any other
MAC.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for PF control over the VF vlan configuration.
I.e., `ip link ... vf <x> vlan <vid>' should now be supported.
1. <vid> != 0 => VF receives [unknowingly] only traffic tagged by
<vid> and tags all outgoing traffic sent by VF with <vid>.
2. <vid> == 0 ==> Remove the pvid configuration, reverting to previous.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a PCI callback for `sriov_configure' and a new PCI device id for
the VF [+ Some minor changes to accomodate differences between PF and VF
at the qede].
Following this, VF creation should be possible and the entire subset of
existing PF functionality that's allow to VFs should be supported.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the VF infrastructure is supposed to offer backward/forward
compatibility, the various types associated with VF<->PF communication
should be aligned across all various platforms that support IOV
on our family of adapters.
This adds a couple of currently missing values, specifically aligning
the enum for the various TLVs possible in the communication between them.
It then adds the PF implementation for some of those missing VF requests.
This support isn't really necessary for the Linux VF as those VFs aren't
requiring it [at least today], but are required by VFs running on other
OSes. LRO is an example of one such configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up to this point, VF and PF communication always originates from VF.
As a result, VF cannot be notified of any async changes, and specifically
cannot be informed of the current link state.
This introduces the bulletin board, the mechanism through which the PF
is going to communicate async notifications back to the VF. basically,
it's a well-defined structure agreed by both PF and VF which the VF would
continuously poll and into which the PF would DMA messages when needed.
[Bulletin board is actually allocated and communicated in previous patches
but never before used]
Based on the bulletin infrastructure, the VF can query its link status
and receive said async carrier changes.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds sufficient changes to allow VFs l2-configuration flows to work.
While the fastpath of the VF and the PF are meant to be exactly the same,
the configuration of the VF is done by the PF.
This diverges all VF-related configuration flows that originate from a VF,
making them pass through the VF->PF channel and adding sufficient logic
on the PF side to support them.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.
It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.
This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Communication between VF and PF is based on a dedicated HW channel;
VF will prepare a messge, and by signaling the HW the PF would get a
notification of that message existance. The PF would then copy the
message, process it and DMA an answer back to the VF as a response.
The messages themselves are TLV-based - allowing easier backward/forward
compatibility.
This patch adds the infrastructure of the channel on the PF side -
starting with the arrival of the notification and ending with DMAing
the response back to the VF.
It also adds a dummy-response as reference, as it only lays the
groundwork of the communication; it doesn't really add support of any
actual messages.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a new Kconfig option for qed* driver which would allow
[eventually] the support in VFs.
This patch adds the necessary logic in the PF to learn about the possible
VFs it will have to support [Based on PCI configuration space and HW],
and prepare a database with an entry per-VF as infrastructure for future
interaction with said VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qlcnic_fw_cmd_get_minidump_temp() fails then "fw_dump->tmpl_hdr" is
NULL or possibly freed. It can lead to an oops later.
Fixes: d01a6d3c8a ('qlcnic: Add support to enable capability to extend minidump for iSCSI')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
"data_split" was never set to false. It's just uninitialized.
Fixes: 2950219d87 ('qede: Add basic network device support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling is broken here. netxen_rom_fast_read() returns zero
on success and -EIO on error. It never returns -1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that we are using "autoneg" without
initializing it. The problem is the ->phy_read() condition is reversed
so we only set this on error instead of success.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complained that "v" can be used unintialized if
netxen_rom_fast_read() returns -EIO. That function never actually
returns -1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qede requires qed to provide enough resources to accommodate 16 combined
channels, but that upper-bound isn't actually being enforced by it.
Instead, qed inform back to qede how many channels can be opened based on
available resources - but that calculation doesn't really take into account
the resources requested by qede; Instead it considers other FW/HW available
resources.
As a result, if a user would increase the number of channels to more than
16 [e.g., using ethtool] the chip would hang.
This change increments the resources requested by qede to 64 combined
channels instead of 16; This value is an upper bound on the possible
available channels [due to other FW/HW resources].
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure and enable various tunnels on the
adapter after PF start.
This change was missed as a part of
'commit 464f664501
("qed: Add infrastructure support for tunneling")'
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the qede implementation for internal loopback test.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the qede ethtool support for the following tests:
- interrupt test
- memory test
- register test
- clock test
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functionality and APIs needed for selftests.
It adds the ability to configure the link-mode which is required for the
implementation of loopback tests. It adds the APIs for clock test,
register test, interrupt test and memory test.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in the conflicts.
In the macsec case, the change of the default ID macro
name overlapped with the 64-bit netlink attribute alignment
fixes in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PF minimum bandwidth update
or configuration notified by management firmware.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PF maximum bandwidth update
or configuration notified by management firmware.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds relevant APIs needed to configure WFQ
(Weighted fair queueing) values for the vports. WFQ configuration
is used per vport basis when minimum bandwidth update/configuration
is notified to the PF by the management firmware.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The APIs for making this sort of configuration [e.g., via ethtool] are
already present in qede, but the current configuration flow in qed doesn't
respect it.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's some inconsistency in current logic determining whether the
link settings of a given interface can be changed; I.e., in all modes
other than the so-called `deault' mode the interfaces are forbidden from
changing the configuration - but even this rule is not applied to all
user APIs that may change the configuration.
Instead, let the core-module [qed] decide whether an interface can change
the configuration by supporting a new API function. We also revise the
current rule, allowing all interfaces to change their configurations while
laying the infrastructure for future modes where an interface would be
blocked from making such a configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a getter for the interfaces private flags.
The only parameter currently supported is whether the interface is a
coupled function [required for supporting 100g].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a difference in statsitics' names starting at qed and
propagating to qede, where egress counters indicate ranges while ingress
counters indiciate high-end.
Align all statistcs to follow the same conventions - name indicates range.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just updating the version as many fixes got
accumulated over 5.3.63
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic_attach_func requires rtnl_lock to be held.
Cc: Dept-GELinuxNICDev@qlogic.com
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In firmware assisted GRO flow there could be a single MTU sized
segment arriving due to firmware aggregation timeout/last segment
in an aggregation flow, which is not expected to be an actual gro
packet. So If a skb has zero frags from the GRO flow then simply
push it in the stack as non gso skb.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skb's network header needs to be set before extracting IPv4/IPv6
headers from it.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles memory allocation failures for fastpath
gracefully in the driver.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables netdev tunneling features and adds
TX/RX fastpath support for tunneling in driver.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables GENEVE tunnel on the adapter and
add support for driver hooks to configure UDP ports
for GENEVE tunnel offload to be performed by the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables VXLAN tunnel on the adapter and
add support for driver hooks to configure UDP ports
for VXLAN tunnel offload to be performed by the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds various structure/APIs needed to configure/enable different
tunnel [VXLAN/GRE/GENEVE] parameters on the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace deprecated create_singlethread_workqueue with
alloc_ordered_workqueue.
Work items include getting tx/rx frame sizes, resetting MPI processor,
setting asic recovery bit so ordering seems necessary as only one work
item should be in queue/executing at any given time, hence the use of
alloc_ordered_workqueue.
WQ_MEM_RECLAIM flag has been set since ethernet devices seem to sit in
memory reclaim path, so to guarantee forward progress regardless of
memory pressure.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for the following via ethtool:
- UDP configuration of RSS based on 2-tuple/4-tuple.
- RSS hash key.
- RSS indirection table.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the required API for passing RSS-related configuration from qede.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inbox drivers don't need versioning scheme in order to guarantee
compatibility, as both qed and qede are compiled from same codebase.
Signed-off-by: Rahul Verma <rahul.verma@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in the case where qed_slowpath_irq_req is not called, rc is not
assigned and so qed_int_igu_enable will return a garbage value.
Fix this by initializing rc to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just updating version as many fixes got
accumulated over 1.00.00.34
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running small packets [length < 256 bytes] traffic, packets were
being dropped due to invalid data in those packets which were
delivered by the driver upto the stack. Using pci_dma_sync_single_for_cpu
ensures copying latest and updated data into skb from the receive buffer.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the scenario where slowpath configuration isn't passing due to
various pause configurations affecting the chip, the theoretical time
required in worst-case-scenario to empty hw fifos sufficiently to
guarantee that slowpath configuration would flow is currently
insufficient.
This increases such a drain request to the theoretical maximum.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle a new message from the MFW, one that indicate that the transciever
state has changed, and log that into the system logs.
Signed-off-by: Zvi Nachmani <Zvi.Nachmani@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver interaction with the managemnt firmware is done via mailbox
commands which the management firmware periodically sample, as well
as placing of additional data in set places in the shared memory.
Each PF has a single designated mailbox address, and all flows that
require messaging to the management should use it.
This patch does 2 things:
1. It re-defines the critical section surrounding the mailbox sending -
that section should include the setting of the shared memory as well as
the sending of the command [otherwise a race might send a command with
the data of a different command].
2. It moves the locking scheme from using mutices into using spinlocks.
This lays the groundwork for sending MFW commands from non-sleepable
contexts.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is configured for Multi-function mode, some older management
firmware might incorrectly notify interfaces of link changes while they
haven't requested the physical link configuration to be set.
This can create bizzare race conditions where unloading interfaces are
getting notified that the link is up.
Let the driver compensate - store the logical requested state of the link
and don't propagate notifications after protocol driver explicitly
requires the link to be unset.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'commit 55482edc25
("qede: Add slowpath/fastpath support and enable hardware GRO")'
introduces below error when compiling net-next with "make ARCH=x86_64"
drivers/built-in.o: In function `qede_rx_int':
qede_main.c:(.text+0x6101a0): undefined reference to `tcp_gro_complete'
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o While the driver is in the middle of a MB completion processing
and it receives a spurious MB interrupt, it is mistaken as a good MB
completion interrupt leading to premature completion of the next MB
request. Fix the driver to guard against this by checking the current
state of MB processing and ignore the spurious interrupt.
Also added a stats counter to record this condition.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o atomic_t usage is incorrect as we are not implementing
any atomicity.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures hardware to use GRO and adds support
for fastpath APIs to handle HW aggregated packets.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds mainly structures and APIs prototype changes
in order to give support for qede slowpath/fastpath support
for the same.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of problems when initializing the chip, the error flows aren't
being properly done. Specifically, it's possible that the chip would be
left in a configuration allowing it [internally] to access the host
memory, causing fatal problems in the device that would require power
cycle to overcome.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current statistics logic is meant for L2, not for all future protocols.
Move this content to the proper designated file.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BB_A0 is a development model that is will not reach actual clients.
In fact, future firmware would simply fail to initialize such chip.
This changes the configuration into B0 instead of A0, and adds a safeguard
against the slim chance someone would actually try this with an A0 adapter
in which case probe would gracefully fail.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver learns the inner bar sized from a register configured by management
firmware, but older versions are not setting this register.
But since we know which values were configured back then, use them instead.
Signed-off-by: Ram Amrani <Ram.Amrani@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch utilizes the attention infrastructure to log additional
information that relates only to specific HW blocks.
For some of those HW blocks, it also stops automatically disabling the
attention generation as the attention is considered benign and thus
should only be logged; No fear of it flooding the system.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each HW block contains common information about attention reasons,
raising a bit for each one of the different sub-reasons that caused it
to raise an attention.
This patch extends the infrastructure by allowing logging of the various
reasons causing the HW blocks to generate an attention.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW is capable of generating attentnions for a multitude of reasons,
but current driver is enabling attention generation only for management
firmware [required for link notifications].
This patch enables almost all of the possible reasons for HW attentions,
logging the HW block generating the attention and preventing further
attentions from that source [to prevent possible attention flood].
It also lays the infrastructure for additional exploration of the various
attentions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the `QL4xxx 40G/100G' and use `FastLinQ 4xxxx' instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't allow driver to probe on an adapter at a failed state;
Gracefully block the probe instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Module is using a binary firmware file and so should be marked as such.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several corner cases where driver might get a 2nd notification
about the same link change. Don't log any additional changes if the
physical carrier is already reported as it should.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a corner-case in HW where an SKB queued for transmission that
contains too many frags will cause FW to assert.
This patch solves this by linearizing the SKB if necessary.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device ID for the 10g module has changed. Populate the pci_ids table
accordingly.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the use of kobj_to_dev() helper function instead of open
coding it with container_of()
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@@
expression a;
symbol kobj;
@@
- container_of(a, struct device, kobj)
+ kobj_to_dev(a)
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW hsi contains regpairs, mostly for 64-bit address representations.
Since same paradigm is applied each time a regpair is filled, this
introduces a new utility macro for setting such regpairs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each configuration element send via ramrod requires a Slow Path Queue
entry. This slightly changes the way such an entry is configured, but
contains mostly semantic changes [where more parameters are gathered
in a sub-struct instead of being directly passed].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to HW design, some of the memories are wide-bus and access to those
needs to be sequentialized on a per-HW-block level; Read/write to a
given HW-block might break other read/write to wide-bus memory done at
~same time.
Status blocks initialization in CAU is done into such a wide-bus memory.
This moves the initialization into using DMAE which is guaranteed to be
safe to use on such memories.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial driver submission used GFP_ATOMIC almost inclusively when
allocating memory. We now remedy this point, using GFP_KERNEL where
it's possible.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device would start receiving only vlan-tagged traffic with tags matching
that of one of the configured vlan IDs, unless:
- Device is expliicly placed in PROMISC mode.
- Device exhausts its vlan filter credits.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, interfaces are working in vlan-promisc mode; But once
vlan filtering offloaded would be supported, we'll need a method to
control it directly [e.g., when setting device to PROMISC, or when
running out of vlan credits].
This adds the necessary API for L2 client to manually choose whether to
accept all vlans or only those for which filters were configured.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the qed* driver into utilizing the 8.7.3.0 FW.
This new FW is required for a lot of new SW features, including:
- Vlan filtering offload
- Encapsulation offload support
- HW ingress aggregations
As well as paving the way for the possibility of adding storage protocols
in the future.
V2:
- Fix kbuild test robot error/warnings.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since qlcnic_alloc_mbx_args can be failed,
return value should be checked.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qlcnic_dcb_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, if we succeeded on the last iteration through the
loop then we still returned failure.
Fixes: 389e4e04ad ('qlcnic: fix a timeout loop')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem here is that at the end of the loop we test for if
idc->vnic_wait_limit is zero, but since idc->vnic_wait_limit-- is a
post-op, it actually ends up set to (u8)-1. I have fixed this by
moving the decrement inside the loop.
Fixes: 486a5bc77a ('qlcnic: Add support for 83xx suspend and resume.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem here is that after the loop we test for "if (!i) " but
because "i--" is a post-op we exit with i set to -1. I have fixed this
by changing it to a pre-op instead. I had to change the starting value
from 3 to 4 so that we still iterate 3 times.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using INTa, ISR might be called before device is configured
for INTa [E.g., due to other device asserting the shared interrupt line],
in which case the ISR would read the SISR registers that shouldn't be
read unless HW is already configured for INTa. This might break interrupts
later on. There's also an MSI-X issue due to this difference, although
it's mostly theoretical.
This patch changes the initialization order, calling request_irq() for the
slowpath interrupt only after the chip is configured for working
in the preferred interrupt mode.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can't rely on pci config space to discover bar size,
as in some environments this returns a wrong, too large value.
Instead, rely on device register, which contains the value
provided by MFW at preboot.
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Concurrent non-blocking slowpath ramrods can be completed
out-of-order on the completion chain. Recycling completed elements,
while previously sent elements are still completion pending,
can lead to overriding of active elements on the chain. Furthermore,
sending pending slowpath ramrods currently lacks the update of the
chain element physical pointer.
This patch:
* Ensures that ramrods are sent to the FW with
consecutive echo values.
* Handles out-of-order completions by freeing only first
successive completed entries.
* Updates the chain element physical pointer when copying
a pending element into a free element for sending.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>