Add geneve Rx offload support for x550em_a.
The implementation follows the vxlan code with the lower 16 bits of
the VXLANCTRL register holding the UDP port for VXLAN and the upper
for Geneve.
Disabled NFS filters in the RFCTL register which allows us to simplify
the check for VXLAN and Geneve packets in ixgbe_rx_checksum().
Removed vxlan from the name of the callback functions and replaced it
with udp_tunnel which is more in line with the new API.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use atomic bitwise operations when setting and checking reset
requests. This should help with possible races in the service task.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a write the TXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.
The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.
Fixes: a85a970af2 ("net_sched: move tc_action into tcf_common")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit. This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV. This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.
Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.
Fixes: 1636956491 ("ixgbe: Add support for VLAN promiscuous with SR-IOV")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-07-22
This series contains updates to ixgbe and ixgbevf only.
Emil fixes the NACK check in ixgbevf_set_uc_addr_vf() for instances where
the index is not equal to zero. Fixes an issue where mac->ops.setup_fc
can be NULL for backplanes which can cause the driver to crash on load.
Don fixes the second parameter of the LED functions, which is the index to
the LED we are interested in affecting. Fixed variable to store register
reads to unsigned integer. Adds support for the new x553 hardware into
ixgbevf. Fixed a missing rtnl lock around ixgbevf_reinit_locked().
Fixed an issue where in ixgbevf_reset_subtask() was not verifying that
the port has been removed. Cleans up the initial crosstalk fix, since
the SFP that indicates the presence of a SFP+ module changes between
hardware types.
Babu Moger fixes typo in freeing IRQ, since the array subscript increments
after the execution of the statement.
Wei Yongjun adds the missing destroy_workqueue() before returning from
ixgbe_init_module() in the error handling case.
Tony adds range checking for setting the MTU from the VF, where the PF can
return a NACK but this was not passed on to the VF, so propagate the
results from the PF to the VF so errors can be reported. Consolidates
mailbox read and write functions, since the recent changes to
ixgbevf_write_msg_read_ack(), other functions are performing the same
operations done here.
Colin Ian King removes a redundant check on ret_val, since ret_val has
not changed since the previous check.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch address a few issues with the initial crosstalk fix. Most
important of which is the SDP that indicates the presents of a SFP+
module changes between HW types. With this change that is taken in
to consideration
It also moves the check closer to the base code that checks link. This
makes it so we only need to do the check in one spot.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the missing destroy_workqueue() before return from
ixgbe_init_module() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The array subscript increments after the execution of the statement.
So there is no issue here. However it helps to read the code better.
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the function ixgbe_poll() returns 0 when it clean completely
the rx rings, but this foul budget accounting in core code.
Fix this returning the actual work done, capped to weight - 1, since
the core doesn't allow to return the full budget when the driver modifies
the napi status
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some comments weren't updated to reflect the renaming of ndo's and the
change of arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For u32 classifier filters, avoid overwriting existing filter
in a hardware location without removing it first, to clean up
inconsistencies due to duplicate values for filter location.
Verified with the following filters:
Create child hash tables:
handle 1: u32 divisor 1
handle 2: u32 divisor 1
Link to the child hash table from parent hash table:
handle 800:0:11 u32 ht 800: link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 6 ff match ip dst 15.0.0.1/32
handle 800:0:12 u32 ht 800: link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 17 ff match ip dst 16.0.0.1/32
Add filter into child hash table:
handle 1:0:3 u32 ht 1: \
match tcp src 22 ffff action drop
Add another filter to the same location:
handle 2:0:3 u32 ht 2: \
match tcp src 33 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On deleting filters which are links to a child hash table, the filters
in the child hash table must be cleared from the hardware if there
is no link between the parent and child hash table.
Verified with the following filters:
Create a child hash table:
handle 1: u32 divisor 1
Link to the child hash table from parent hash table:
handle 800:0:10 u32 ht 800: link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 6 ff match ip dst 15.0.0.1/32
Add filters into child hash table:
handle 1:0:2 u32 ht 1: \
match tcp src 22 ffff action drop
handle 1:0:3 u32 ht 1: \
match tcp src 33 ffff action drop
Delete link filter from parent hash table:
handle 800:0:10 u32
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we do have pci_request_mem_regions() and pci_release_mem_regions()
at hand, use it in the Intel ethernet drivers.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
In addition I updated the socket address family check so that instead of
excluding IPv6 we instead abort of type is not IPv4. This makes much more
sense as we should only be supporting IPv4 outer addresses on this
hardware.
The last change is that I pulled the rtnl_lock/unlock into the conditional
statement for IXGBE_FLAG2_VXLAN_REREG_NEEDED. The motivation behind this
is to avoid unneeded bouncing of the mutex which will just slow down the
handling of this call anyway.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for offloading IPXIP6 type packets that represent
either IPv4 or IPv6 encapsulated inside of an IPv6 outer IP header. In
addition with this change we should also be able to support FOU
encapsulated traffic with outer IPv6 headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like at some point I somehow transposed the location of setting
the VLAN features in netdev->features and the configuration of the
vlan_features. As a result the driver is now generating a warning about
vlan_features being setup incorrectly.
This patch corrects that by placing the update of netdev->features to
include the VLAN features so that it is after the point where we write
netdev->features into netdev->vlan_features.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Swap the parameters in GENMASK in order to generate the correct mask.
This change fixes Tx hangs when enabling SRIOV.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-05-04
This series contains updates to ixgbe, ixgbevf and traffic class helpers.
Sridhar adds helper functions to the tc_mirred header to access tcf_mirred
information and then implements them for ixgbe to enable redirection to
a SRIOV VF or an offloaded MACVLAN device queue via tc 'mirred' action.
Amritha adds support to set filters with multiple header fields (L3,L4)
to match on.
KY Srinivasan from Microsoft add Hyper-V support into ixgbevf.
Emil adds 82599 sub-device IDs that were missing from the list of parts
that support WoL. Then simplified the logic we use to determine WoL
support by reading the EEPROM bits for MACs X540 and newer.
Preethi cleaned up duplicate and unused device IDs. Fixed our ethtool
stat reporting where we were ignoring higher 32 bits of stats registers,
so fill out 64 bit stat values into two 32 bit words.
Babu Moger from Oracle improves VF performance issues on SPARC.
Alex Duyck cleans up some of the Hyper-V implementation from KY so that
we can just use function pointers instead of having to identify if a
given VF is running on a Linux or Windows PF.
Usha makes sure that DCB and FCoE is disabled for X550EM_x/a MACs and
cleans up the DCB initialization in the process.
Tony cleans up the API for ixgbevf_update_xcast_mode() so we do not
have to pass in the netdev parameter, since it was never used in the
function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
a trans_start struct member exists twice:
- in struct net_device (legacy)
- in struct netdev_queue
Instead of open-coding dev->trans_start usage to obtain the current
trans_start value, use dev_trans_start() instead.
This is not exactly the same, as dev_trans_start also considers
the trans_start values of the netdev queues owned by the device
and provides the most recent one.
For legacy devices this doesn't matter as dev_trans_start can cope
with netdev trans_start values of 0 (they are ignored).
This is a prerequisite to eventual removal of dev->trans_start.
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IXGBE_FLAG_DCB_CAPABLE flag that is set
for all MACs other than X550EM_x and x550em_a. DCB and
FCoE is disabled for these MACS. DCB initialization
code is moved to a separate function.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Ronald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change aims to simplify the logic we use to determine WOL
support by reading the EEPROM bits for MACs X540 and newer.
Also some cleanups in ixgbe_wol_supported() - changed return type to
bool and removed redundant return variable by simply using return after
the checks.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We had some 82599 subdevice IDs missing from the list of parts that
support WoL.
Reported-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds support to set filters with multiple header fields (L3,L4)to match on.
This is achieved in the following order:
1. Create a leaf hash table for the next header.
2. Create a link to the leaf hash table from the base hash table with
matches on next header type and current header fields.
3. Add filter in leaf hash table with match on next header fields and
action.
Verified with the following filters :
Match TCP and DIP:
handle 1: u32 divisor 1
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 6 ff match ip dst 10.0.0.1/32
match tcp src 28 ffff action drop
Delete the filter:
Match on DIP, SIP, UDP (SPort, DPort):
handle 2: u32 divisor 1
u32 ht 800: order 2 link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip dst 15.0.0.2/32 match ip protocol 17 ff \
match ip src 15.0.0.1/32
match udp src 30 ffff match udp dst 32 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables 'redirect' to a SRIOV VF or a offloaded macvlan
device queue via tc 'mirred' action.
Verified with the following script that creates SRIOV VFs, offloaded
macvlan and adds tc u32 filters with redirect action to the associated
netdevs.
# add ingress qdisc.
tc qdisc add dev p4p1 ingress
# enable hw tc offload.
ethtool -K p4p1 hw-tc-offload on
# create 4 sriov VFs and bring up the first one.
echo 4 > /sys/class/net/p4p1/device/sriov_numvfs
sleep 1
ip link set p4p1 up
ip link set p4p1_0 up
# create a offloaded macvlan device and bring it up.
ethtool -K p4p1 l2-fwd-offload on
ip link add link p4p1 name mvlan_1 type macvlan
ip link set mvlan_1 up
# add u32 filter with action to redirect to VF netdev
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: \
match ip src 192.168.1.3/32 \
action mirred egress redirect dev p4p1_0
# add u32 filter with action to redirect to macvlan netdev
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: \
match ip src 192.168.2.3/32 \
action mirred egress redirect dev mvlan_1
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for partial GSO segmentation in the case of
tunnels. Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header. This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make use of GENMASK instead of open coding the equivalent operation
incorrectly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several areas of ixgbe were written before widespread usage of the
BIT(n) macro. With the impending release of GCC 6 and its associated new
warnings, some usages such as (1 << 31) have been noted within the ixgbe
driver source. Fix these wholesale and prevent future issues by simply
using BIT macro instead of hand coded bit shifts.
Also fix a few shifts that are shifting values into place by using the
'u' prefix to indicate unsigned. It doesn't strictly matter in these
cases because we're not shifting by too large a value, but these are all
unsigned values and should be indicated as such.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible on some systems that crosstalk could lead to link flap
on empty SFP+ cages. A new NVM bit was defined to let SW know it
needs to implement the work around which consists of verifying that
there is a module in the cage before acting on the LSC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a new register to wait for previous register writes to complete
before issuing a register read. This is needed when slower links
are in use.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Consolidate the logic behind configuring spoof checking:
Move the setting of the MAC, VLAN and Ethertype spoof checking into
ixgbe_ndo_set_vf_spoofchk().
Change ixgbe_set_mac_anti_spoofing() to set MAC spoofing per VF similar
to the VLAN and Ethertype functions - this allows us to call the helper
functions in ixgbe_ndo_set_vf_spoofchk() for all spoof check types and
only disable MAC spoof checking when creating MACVLAN.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
vxlan_get_rx_port requires rtnl_lock to be held.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ixgbe version number.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for x550em_a-based KR backplane devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for an SGMII backplane interface.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for SFPs with an external retimer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for x550em_a 10G MAC type to the ixgbe driver. The new
MAC includes new firmware commands that need to be used to control
PHY and IOSF access, so that support is also added. The interface
supported is a native SFP+ interface.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for a single-port X550 device.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables bulk free in Tx cleanup for ixgbevf and cleans up the
boolean logic in the polling routines for ixgbe and ixgbevf in the hopes of
avoiding any mix-ups similar to what occurred with i40e and i40evf.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can use the ethtool rx-vlan-filter flag to
toggle Rx VLAN filtering on and off. This is basically just an extension
of the existing VLAN promisc work in that it just adds support for the
additional ethtool flag.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added support to match on UDP fields in the transport layer.
Extended core logic to support multiple headers.
Verified with the following filters :
handle 1: u32 divisor 1
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
u32 ht 1: order 2 \
match tcp src 1024 ffff match tcp dst 23 ffff action drop
handle 2: u32 divisor 1
u32 ht 800: order 3 link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 17 ff
u32 ht 2: order 4 \
match udp src 1025 ffff match udp dst 24 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible on some HW that a system reset could occur when we are
holding the SWFW semaphore lock. So next time the driver was loaded we
would see it incorrectly as locked. This patch will recover from that state
by: Attempting to acquire the semaphore and then regardless of whether or
not it was acquire we immediately release it. This will force us into
a known good state.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit adds a callback which allows to adjust the maximum transmit
bitrate the card can output. This makes it possible to get a smooth
traffic instead of the default burst-y behaviour when trying to output
e.g. a video stream.
Much of the logic needed to get a correct bcnrc_val was taken from the
ixgbe_set_vf_rate_limit() function.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for generic Tx checksums to the ixgbe driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit converts commit c762dff24c ("ixgbe: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d10549 ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The source for the ops structure contents are const, so make them
so. Copy them in place with structure assignments instead of memcpys.
Make the mbx_ops accessed by reference instead of making a copy of
the source structure. Update copyright date on the touched files.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were adding VLAN 0 twice each time we restored the VLAN configuration.
Instead of doing it twice we can just start working through the active
VLANs from ID 1 on and skip the double write.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While doing the work on igb I realized there were a few cases where we were
still adding VLANs to the VLVF entries for the PF when they were not
needed. This patch cleans that up so that the only time we add a PF entry
to the VLVF is either for VLAN 0 or if the PF has requested a VLAN that a VF
is already using.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the incorrect check for mask in ixgbe_configure_clsu32 and
drop the 'mask' field that is not required in struct ixgbe_mat_field
Verified with the following filters:
#tc qdisc add dev p4p1 ingress
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: \
match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: \
match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:3 u32 ht 800: \
match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:4 u32 ht 800: \
match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for handle ids when adding/deleting hash nodes OR adding/deleting
filter entries and limit them to max number of links or header nodes
supported(IXGBE_MAX_LINK_HANDLE).
Start from bit 0 when setting hash table bit-map.(adapter->tables)
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function is only used in ixgbe_main.c
Resolves a "missing prototype" warning when building the driver with W=1
Reported-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ATR code was assuming that it would be able to use tcp_hdr for
every TCP frame that came through. However this isn't the case as it
is possible for a frame to arrive that is TCP but sent through something
like a raw socket. As a result the driver was setting up bad filters in
which tcp_hdr was really pointing to the network header so the data was
all invalid.
In order to correct this I have added a bit of parsing logic that will
determine the TCP header location based off of the network header and
either the offset in the case of the IPv4 header, or a walk through the
IPv6 extension headers until it encounters the header that indicates
IPPROTO_TCP. In addition I have added checks to verify that the lowest
protocol provided is recognized as IPv4 or IPv6 to help mitigate raw
sockets using ETH_P_ALL from having ATR applied to them.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VXLAN port number should be stored in network order instead of in host
order as it is accessed from the hot-path in ATR. This way we can avoid
having to do any byte swaps in order to validate the port number.
I moved the vxlan_port value into a hole in the read-mostly region of the
adapter struct. This way it should be in a warm cache-line instead of in
some isolated region in memory when it needs to be accessed.
In addition I went through and stripped a bunch of unneeded ifdef flags
since having an extra variable present doesn't really hurt anything and
makes the code easier to read. I also went through and dropped the
NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides
no value as the flag is not evaluated in the Rx path.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit c9f53e63c2 ("ixgbe: Refactor MAC address configuration code")
introduced code that doesn't set HW register RAR0 to default mac address
but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets
that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF.
This commit sets RAR0 correctly to default HW mac address.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original series drivers would get offload requests for cls_u32
rules even if the feature bit is disabled. This meant the driver had
to do a boiler plate check on the feature bit before adding/deleting
the rule.
This patch lifts the check into the core code and removes it from the
driver specific case.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures ixgbe will not try to offload hash tables from the
u32 module. The device class does not currently support this so until
it is enabled just abort on these tables.
Interestingly the more flexible your hardware is the less code you
need to implement to guard against these cases.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds initial support for offloading the u32 tc classifier. This
initial implementation only implements a few base matches and actions
to illustrate the use of the infrastructure patches.
However it is an interesting subset because it handles the u32 next
hdr logic to correctly map tcp packets from ip headers using the ihl
and protocol fields. After this is accepted we can extend the match
and action fields easily by updating the model header file.
Also only the drop action is supported initially.
Here is a short test script,
#tc qdisc add dev eth4 ingress
#tc filter add dev eth4 parent ffff: protocol ip \
u32 ht 800: order 1 \
match ip dst 15.0.0.1/32 match ip src 15.0.0.2/32 action drop
<-- hardware has dst/src ip match rule installed -->
#tc filter del dev eth4 parent ffff: prio 49152
#tc filter add dev eth4 parent ffff: protocol ip prio 99 \
handle 1: u32 divisor 1
#tc filter add dev eth4 protocol ip parent ffff: prio 99 \
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
#tc filter add dev eth4 parent ffff: protocol ip \
u32 ht 1: order 3 match tcp src 23 ffff action drop
<-- hardware has tcp src port rule installed -->
#tc qdisc del dev eth4 parent ffff:
<-- hardware cleaned up -->
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an opportunity to bulk free SKBs during reclaiming of
resources after DMA transmit completes in ixgbe_clean_tx_irq. Thus,
bulk freeing at this point does not introduce any added latency.
Simply use napi_consume_skb() which were recently introduced. The
napi_budget parameter is needed by napi_consume_skb() to detect if it
is called from netpoll.
Benchmarking IPv4-forwarding, on CPU i7-4790K @4.2GHz (no turbo boost)
Single CPU/flow numbers: before: 1982144 pps -> after : 2064446 pps
Improvement: +82302 pps, -20 nanosec, +4.1%
(SLUB and GCC version 5.1.1 20150618 (Red Hat 5.1.1-4))
Joint work with Alexander Duyck.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now ATR is not handling IPv6 extended headers, so ATR is not
being performed on such packets. Fix that by skipping extended
headers when they are present. This also fixes a problem where
the ATR code was not checking that the inner protocol was actually
TCP before setting up the signature rules. Since the protocol check
is intimately involved with the extended header processing as well,
this all gets fixed together.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When FCoE is enabled with SR-IOV on the X550 NIC the hardware
generates MDD events.
This patch fixes these by setting the expected values in the
Tx context descriptors for FCoE/FIP frames and adding a flush
after writing the RDLEN register.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an outer UDP checksum is set, pass the skb up with CHECKSUM_NONE
so that the stack will check the checksum. Do not increment an
error counter, because we don't know that there is an actual error.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up minor redundancy in the setting of hw_enc_features that
makes it appears that X550 uniquely has more encapsulation features
than other devices. The driver only supports one more feature, so
make it look that way. No longer set NETIF_F_SG since that is set
by the register_netdev call. Thanks to Alex Duyck for noticing this
slight confusion.
Reported-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a follow-on for enabling VLAN promiscuous and allowing the PF
to add VLANs without adding a VLVF entry. What this patch does is go
through and free the VLVF registers if they are not needed as the VLAN
belongs only to the PF which is the default pool.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for VLAN promiscuous with SR-IOV enabled.
The code prior to this patch was only adding the PF to VLANs that the VF
had added. As such enabling promiscuous mode would actually not add any
additional VLAN filters so visibility was limited. This lead to a number
of issues as the bridge and OVS would expect us to accept all VLAN tagged
packets when promiscuous mode was enabled, and instead we would filter out
most if not all depending on the configuration of the PF.
With this patch what we do is set all the bits in the VFTA and all of the
VLVF bits associated with the pool belonging to the PF. By doing this the
PF is guaranteed to receive all VLAN tagged traffic associated with the RAR
filters assigned to the PF. In addition we will clean up those same bits
in the event of promiscuous mode being disabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for bypassing the VLVF entry creation when the PF
is adding a new VLAN. The advantage to doing this is that we can then save
the VLVF entries for the VFs which must have them in order to function,
versus the PF which can fall back on the default pool entry.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a check to make certain mac_table was actually allocated and is not
NULL. If it is NULL return -ENOMEM and allow the probe routine to fail
rather then causing a NULL pointer dereference further down the line.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state. Specifically the MAC address was
enabled for both VF 0 and the PF. This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.
A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.
In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.
Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000
Result:
MPSAR[0] 00000081
MPSAR[254] 00000001
Expected Result, behavior after patch:
MPSAR[0] 00000080
MPSAR[254] 00000080
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we allow the PF to make use of all free RAR
entries for FDB use if needed.
Previously the code limited us to 16 unicast entries, however this was
shared between MACVLAN which wasn't limited and the FDB code which was. So
instead of treating the FDB code as a second class citizen I have updated
it so that it has access to just as many entries as the MACVLAN filters.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode
with a call to __dev_uc_sync instead. This works much better with the MAC
addr list code that was already in place and solves an issue in which you
couldn't remove an FDB address without having to reset the port.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the process of tracking down a memory leak when adding/removing FDB
entries I had to go through the MAC address configuration code for ixgbe.
In the process of doing so I found a number of issues that impacted
readability and performance. This change updates the code in general to
clean it up so it becomes clear what each step is doing. From what I can
tell there a couple of bugs cleaned up in this code.
First is the fact that the MAC addresses were being double counted for the
PF. As a result once entries up to 63 had been used you could no longer
add additional filters.
A simple test case for this:
for i in `seq 0 96`
do
ip link add link ens8 name mv$i type macvlan
ip link set dev mv$i up
done
Test script:
ethregs -s 0:8.0 | grep -e "RAH" | grep 8000....$
When things are working correctly RAL/H registers 1 - 97 will be consumed.
In the failing case it will stop at 63 and prevent any further filters from
being added.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_intr and ixgbe/ixgbevf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit dfaf891dd3 ("ixgbe: Refactor the RSS configuration code")
introduced a few kernel-doc errors:
1) The function name is missing;
2) The format is wrong;
3) The short description is redundant.
Fix all the above for the correct execution of the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delete a redundant include of net/vxlan.h.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the new netdev op to trust VF in ixgbe.
The administrator can turn on and off VF trusted by ip command which
supports trust message.
# ip link set dev eth0 vf 1 trust on
or
# ip link set dev eth0 vf 1 trust off
Send a ping to reset VF on changing the status of trusting.
VF driver will reconfigure its features on reset.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch disables LRO by default in favor of GRO.
LRO is incompatible with forwarding and is disabled when forwarding
is turned on which makes the default offloads of the driver
inconsistent. LRO can still be enabled via ethtool.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that flow control packets initiated by the VF are
dropped and reported as spoofed.
Flow control packets can be used to limit the throughput or as DOS
attack when generated from a VF. Flow control is not supported per VF
hence any pause frames generated from a VF are considered malicious.
Also cleaned up indentation and some redundant comments.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the addition of X550em_x SFP+ support, the driver is now
functionally equivalent to what will be the 4.2.1 driver when
released, so change the version to match.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 thermal interrupt (IXGBE_EIMS_TS) is not an SDP, so it
doesn't need to be enabled in ixgbe_setup_gpie(). In fact the
value is simply not for the GPIE register at all.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change does two things. First, it makes it so that we always
set the relaxed ordering bits related to the DCA registers even if
DCA is not enabled. Second, it moves the configuration out of the
ixgbe_down function and into the ixgbe_configure function before
enabling the Rx and Tx rings. This ensures that DCA is configured
correctly before starting to process packets.
Thanks to Alex Duyck for this fix.
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
