The amount of TX/RX buffers that the vNIC driver currently allocates
is different from the amount agreed upon in negotiation with firmware.
Correct that by allocating the requested number of buffers confirmed
by firmware.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a counter to track the number of outstanding transmissions sent
that have not received completions. If the counter reaches the maximum
number of queue entries, stop transmissions on that queue. As we receive
more completions from firmware, wake the queue once the counter reaches
an acceptable level.
This patch prevents hardware/firmware TX queue from filling up and
and generating errors. Since incorporating this fix, internal testing
has reported that these firmware errors have stopped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds glue-code that allows the EMAC driver to interface
with the existing dt-supported PHYs in drivers/net/phy.
Because currently, the emac driver maintains a small library of
supported phys for in a private phy.c file located in the drivers
directory.
The support is limited to mostly single ethernet transceiver like the:
CIS8201, BCM5248, ET1011C, Marvell 88E1111 and 88E1112, AR8035.
However, routers like the Netgear WNDR4700 and Cisco Meraki MX60(W)
have a 5-port switch (AR8327N) attached to the EMAC. The switch chip
is supported by the qca8k mdio driver, which uses the generic phy
library. Another reason is that PHYLIB also supports the BCM54610,
which was used for the Western Digital My Book Live.
This will now also make EMAC select PHYLIB.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After sending device capability queries and requests to the vNIC Server,
an interrupt is triggered and the responses are written to the driver's
CRQ response buffer. Since the interrupt can be triggered before all
responses are written and visible to the partition, there is a danger
that the interrupt handler or tasklet can terminate before all responses
are read, resulting in a failure to initialize the device.
To avoid this scenario, when capability commands are sent, we set
a flag that will be checked in the following interrupt tasklet that
will handle the capability responses from the server. Once all
responses have been handled, the flag is disabled; and the tasklet
is allowed to terminate.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two different counters were being used for capabilities
requests and queries. These commands are not called
at the same time so there is no reason a single counter
cannot be used.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a tasklet to process queued commands or messages received from
firmware instead of processing them in the interrupt handler. Note that
this handler does not process network traffic, but communications related
to resource allocation and device settings.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error reports received from firmware were not being converted from
big endian values, leading to bogus error codes reported on little
endian systems.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vNIC client driver requests a faulty device setting, the
server returns an acceptable value for the client to request.
This 64 bit value was incorrectly being swapped as a 32 bit value,
resulting in loss of data. This patch corrects that by using
the 64 bit swap function.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.
It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.
Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failure path in ibmvnic_open() mistakenly makes a second call
to napi_enable instead of calling napi_disable. This can result
in a BUG_ON for any queues that were enabled in the previous call
to napi_enable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize condition variables prior to invoking any work that can
mark them complete. This resolves a race in the ibmvnic driver where
the driver faults trying to complete an uninitialized condition
variable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete()
We plan to remove __napi_complete() to reduce NAPI complexity.
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the ibmveth driver in a KVM/QEMU based VM, it currently
always prints out a scary error message like this when it is started:
ibmveth 71000003 (unregistered net_device): unable to change
checksum offload settings. 1 rc=-2 ret_attr=71000003
This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include calculations to compute the number of segments
that comprise an aggregated large packet.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for netdev private data is allocated using kzalloc/vzalloc in
alloc_netdev_mqs, thus there is no need to zero the stats portion of it
again in the driver's probe function.
In any case, the size for the memset is wrong as the stats member is of
type rtnl_link_stats64, not net_device_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate header seq_file.h from ibmvnic.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mistake was causing debugfs directory creation
failures when multiple ibmvnic devices were probed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure was mapped but never subsequently unmapped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the opt_* fields to determine the starting point for negotiating the
number of tx/rx completion queues with the vnic server. These contain the
number of queues that the vnic server estimates that it will be able to
allocate. While renegotiation may still occur, using the opt_* fields will
reduce the number of times this needs to happen and will prevent driver
probe timeout on systems using large numbers of ibmvnic client devices per
vnic port.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ehea driver is missing a call to netif_carrier_off()
before the interface bring-up; this is necessary in order to
initialize the __LINK_STATE_NOCARRIER bit in the net_device state
field. Otherwise, we observe state UNKNOWN on "ip address" command
output.
This patch adds a call to netif_carrier_off() on ehea's net device
open callback.
Reported-by: Xiong Zhou <zhou@redhat.com>
Reference-ID: IBM bz #137702, Red Hat bz #1089134
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: d894be57ca92('ethernet: use net core MTU range checking in more drivers')
CC: Jarod Wilson <jarod@redhat.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the MTU to be changed during the initialization
process with the VNIC Server. Ensure that the net device is updated
to reflect the new MTU.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increment driver version to reflect features that have
been added since release.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea: min_mtu 68, max_mtu 9022
- remove ehea_change_mtu, it's now redundant
emac: min_mtu 46, max_mtu 1500 or whatever gets read from OF
CC: netdev@vger.kernel.org
CC: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for preventing race conditions within ioctl calls.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add realization for mac address set and remove dummy callback.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'd like to eventually remove NO_IRQ on powerpc, so remove usages of it
from powerpc-only drivers.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENOMEM from the dma_map_single error
handling case instead of 0, as done elsewhere in this function.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an open coded simple_open() function and replace file
operations references to the function with simple_open()
instead.
Generated by: scripts/coccinelle/api/simple_open.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An upcoming feature of IBM VNIC protocol is the ability to configure
redundant backing devices for a VNIC client. In case of a failure
on the current backing device, the driver will receive a signal
from the hypervisor indicating that a failover will occur. The driver
will then wait for a message from the backing device before
establishing a new connection.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, if there is no VNIC server available during the driver
probe, the driver should wait until it receives an initialization
request from the VNIC Server to start the login process. Recent testing
has show that this is incorrectly handled in the current driver.
The proposed solution handles this initialization request by scheduling
a task in the shared workqueue that completes the login process and
registers the net device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a function that handles sub-CRQ IRQ creation
separately from sub-CRQ initialization. Another function is then needed
to release sub-CRQ resources prior to sub-CRQ IRQ creation.
These additions allow the driver probe function to be simplified,
specifically during the VNIC Server login process. A timeout is also
included while waiting for completion of the login process in case
the VNIC Server is not available or some other error occurs.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ mappings were not being properly disposed when releasing sub-CRQ's.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ibmvnic uses multiple tx queues, start and stop all queues when
opening and closing devices.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each() macro aptly named
list_for_each_safe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea_get_port may return NULL. Do not dereference NULL value.
Fixes: 8c4877a412 ("ehea: Use the standard logging functions")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the phy initialization code for Qualcomm
Atheros AR8035 phy. This configuration is found in the
Cisco Meraki MR24.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables the use of multiple transmit and receive scrqs allowing the ibmvnic
driver to take advantage of multiqueue functionality. To achieve this, the
driver must implement the process of negotiating the maximum number of
queues allowed by the server. Initially, the driver will attempt to login
with the maximum number of tx and rx queues supported by the server. If
the server fails to allocate the requested number of scrqs, it will return
partial success in the login response. In this case, we must reinitiate
the login process from the request capabilities stage and attempt to login
requesting fewer scrqs.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable RX Checksum offload feature in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the VNIC driver to provide descriptors containing
L2/L3/L4 headers to firmware. This feature is needed
for greater hardware compatibility and enablement of checksum
and TCP offloading features.
A new function is included for the hypervisor call,
H_SEND_SUBCRQ_INDIRECT, allowing a DMA-mapped array of SCRQ
descriptor elements to be sent to the VNIC server.
These additions will help fully enable checksum offloading as
well as other features as they are included later.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_linearize fails, the driver should drop the packet
instead of trying to copy it into the bounce buffer.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic_capability struct was defined incorrectly. The last two
elements of the struct are in the wrong order. In addition, the number
element should be 64-bit. Byteswapping functions are updated
as well.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new device driver for a high performance SR-IOV assisted virtual
network for IBM System p and IBM System i systems. The SR-IOV VF will be
attached to the VIOS partition and mapped to the Linux client via the
hypervisor's VNIC protocol that this driver implements.
This driver is able to perform basic tx and rx, new features
and improvements will be added as they are being developed and tested.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an API consolidation only. The use of kmalloc + memset to 0
is equivalent to kcalloc in this case as it is allocating an array
of elements.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the MAC register dump used to be the size specified by the
reg property in the device tree. Userland has no good way of finding
out that size, and it was not specified consistently for each MAC type,
so ethtool would end up printing junk at the end of the register dump
if the device tree didn't match the size it assumed.
Using the new version numbers indicates unambiguously that the size of
the MAC register dump is dependent only on the MAC type.
Fixes: 5369c71f7c ("net/ibm/emac: fix size of emac dump memory areas")
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_mode can be negative.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a new method of signalling the firmware
that TSO packets are being sent. The new method removes the need to
alter the ip and tcp checksums and allows TSO6 support.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix in send of emac regs dump to ethtool which
causing in wrong data interpretation on ethtool
layer for MII and EMAC.
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables receiving large packets from other LPARs. These packets
have a -1 IP header checksum, so we must recalculate to have
a valid checksum.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TSO. TSO is turned off by default and
must be enabled and configured by the user. The driver
version number is increased so that users can be sure
that they are using ibmveth with TSO support.
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables 64k rx buffer pools by default. If Cooperative
Memory Overcommitment (CMO) is enabled, the number of 64k buffers
is reduced to save memory.
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit to only register the EHEA memory hotplug hooks on
adapter probe has a few problems.
Firstly the reference counting is wrong for multiple adapters, in that
the hooks are registered multiple times. Secondly the check in the tear
down path is backward. Finally the error path doesn't decrement the
count.
The multiple registration of the hooks is the biggest problem, as it
leads to oopses when the system is rebooted, and/or errors during memory
hotplug, eg:
$ ./mem-on-off-test.sh -r 2
...
ehea: memory is going offline
ehea: LPAR memory changed - re-initializing driver
ehea: re-initializing driver complete
ehea: memory is going offline
ehea: LPAR memory changed - re-initializing driver
ehea: opcode=26c ret=fffffffffffffffc arg1=8000000003000003 arg2=0 arg3=700000060000d600 arg4=3fded0000 arg5=200 arg6=0 arg7=0
ehea: register_rpage_mr failed
ehea: registering mr failed
ehea: register MR failed - driver inoperable!
ehea: memory is going offline
Fixes: aa18332331 ("ehea: Register memory hotplug, reboot and crash hooks on adapter probe")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
AFAIK the PAPR document which defines the virtual device interface used by
the ibmveth driver doesn't specify a specific maximum MTU. So, in the
ibmveth driver, the maximum allowed MTU is determined by the maximum
allocated buffer size of 64k (corresponding to one page in the common case)
minus the per-buffer overhead IBMVETH_BUFF_OH (which has value 22 for 14
bytes of ethernet header, plus 8 bytes for an opaque handle).
This suggests a maximum allowable MTU of 65514 bytes, but in fact the
driver only permits a maximum MTU of 65513. This is because there is a <
instead of an <= in ibmveth_change_mtu(), which only permits an MTU which
is strictly smaller than the buffer size, rather than allowing the buffer
to be completely filled.
This patch fixes the buglet.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVL2cxAAoJEFHr6jzI4aWAR8cP/19VTo/CzCE4ffPSx7qR464n
F+WFZcbNjIMXu6+B0YLuJZEsuWtKKrCit/MCg3+mSgE4iqvxmtI+HDD0445Buszj
UD4E4HMdPrXQ+KUSUDORvRjv/FFUXIa94LSv/0g2UeMsPz/HeZlhMxEu7AkXw9Nf
rTxsmRTsOWME85Y/c9ss7XHuWKXT3DJV7fOoK9roSaN3dJAuWTtG3WaKS0nUu0ok
0M81D6ZczoD6ybwh2DUMPD9K6SGxLdQ4OzQwtW6vWzcQIBDfy5Pdeo0iAFhGPvXf
T4LLPkv4cF4AwHsAC4rKDPHQNa+oZBoLlScrHClaebAlDiv+XYKNdMogawUObvSh
h7avKmQr0Ygp1OvvZAaXLhuDJI9FJJ8lf6AOIeULgHsDR9SyKMjZWxRzPe11uarO
Fyi0qj3oJaQu6LjazZraApu8mo+JBtQuD3z3o5GhLxeFtBBF60JXj6zAXJikufnl
kk1/BUF10nKUhtKcDX767AMUCtMH3fp5hx8K/z9T5v+pobJB26Wup1bbdT68pNBT
NjdKUppV6QTjZvCsA6U2/ECu6E9KeIaFtFSL2IRRoiI0dWBN5/5eYn3RGkO2ZFoL
1NdwKA2XJcchwTPkpSRrUG70sYH0uM2AldNYyaLfjzrQqza7Y6lF699ilxWmCN/H
OplzJAE5cQ8Am078veTW
=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are only used from one place each. If the cacheable_*
versions really are more efficient, then those changes should be
migrated into the common code instead.
NOTE: The old routines are just flat buggy on kernels that support
hardware with different cacheline sizes.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The interrupt is enabled before napi_complete(). A network timeout
occurs if the interrupt handler is called before napi_complete().
Fix the bug by enabling the interrupt after napi_complete().
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function that will enable changing the MAC address
of an ibmveth interface while it is still running.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea creates memory hotplug, reboot and crash hooks even if there
are no adapters in the box. Just create them when we probe our
first adapter.
[cascardo: use ehea_register_memory_hooks return code]
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The of_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver claims that it can do TSO and IP checksums on vlan
devices and also allows user to control vlan acceleration offloading.
This makes it possible to push traffic to this driver that has TSO or
partial checksums set, but also have a non-accelearted vlan
header. In this case, the driver will fail to correctly
identify such traffic and will not correctly perform
segmentation and checksum calculation.
Fix this by using vlan_get_protocol() helper instead of
assuming skb->protocol always has this information.
CC: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.
Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Makefile, ehea_phyp.o is included twice in the list of
object files compile into ehea.o.
This change removes one instance.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
