Add another mdp5_hw_mixer pointer (r_mixer) in mdp5_crtc_state.
This mixer will be used to generate the right half of the scanout.
With Source Split, a SSPP can now be connected to 2 Layer Mixers, but
has to be at the same blend level (stage #) on both Layer Mixers.
A drm_plane that has a lesser width than the max width supported, will
comprise of a single SSPP/hwpipe, staged on both the Layer Mixers at
the same blend level. A plane that is greater than max width will comprise
of 2 SSPPs, with the 'left' SSPP staged on the left LM, and the 'right'
SSPP staged on the right LM at the same blend level.
For now, the drm_plane consists of only one SSPP, therefore, it
needs to be staged on both the LMs in blend_setup() and mdp5_ctl_blend().
We'll extend this logic to support 2 hwpipes per plane later.
The crtc cursor ops (using the LM cursors, not SSPP cursors) simply
return an error if they're called when the right mixer is assigned to
the CRTC state. With source split is enabled, we're expected to only
SSPP cursors.
This commit adds code that configures the right mixer, but the r_mixer
itself isn't assigned at the moment.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These are a part of CRTC state, it doesn't feel nice to leave them
hanging in mdp5_ctl struct. Pass mdp5_pipeline pointer instead
wherever it is needed.
We still have some params in mdp5_ctl like start_mask etc which
are derivative of atomic state, and should be rolled back if
a commit fails, but it doesn't seem to cause much trouble.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use the mdp5_hw_mixer struct in the mdp5_crtc and mdp5_ctl instead of
using the LM index.
Like before, the Layer Mixers are assigned statically to the CRTCs.
The hwmixer(s) will later be dynamically assigned to CRTCs.
For now, ignore the hwmixers that can only do WB.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use SSPP_NONE in mdp5_plane_pipe() if there is now hwpipe allocated for
the drm_plane. Returning '0' means we are returning VIG0 pipe.
Also, use the mdp5_pipe enum to pass around the stage array. Initialize
the stage to SSPP_NONE by default.
We do the above because 1) Cursor plane has to be staged at the topmost
blender of the LM, which can result in empty stages in between 2) In
the future, when we support multiple LMs per CRTC. We could have stages
which don't have any pipe assigned to them.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change takes advantage of a HW feature that synchronize
flush operation on CTL1 to CTL0, to keep dual DSI pipes in
sync.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In MDP5, CTL contains information of the whole pipeline whose
output goes down to a display interface. In various cases, one
interface may require 2 CRTCs, but only one CTL. Some interfaces
also require to use certain CTLs.
Instead of allocating CTL for each active CRTC, this change is to
associate a CTL with each interface.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change is to add properties alpha/zpos/blend_mode to mdp5 plane
for alpha blending operation to generate the blended output.
v1: Initial change
v2: Change "premultilied" property to enum (Rob's comment)
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
[Don't actually expose alpha/premultiplied props to userspace yet
pending a chance for discussion and some userspace to exercise it]
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP FLUSH registers could indicate if the previous flush updates
has taken effect at vsync boundary. Making use of this H/W feature
can catch the vsync that happened between CRTC atomic_flush and
*_wait_for_vblanks, to avoid unnecessary wait.
This change allows kms CRTCs to use their own *_wait_for_commit_done
functions to wait for FLUSH register cleared at vsync, before commit
completion.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some interfaces (WB, DSI Command Mode) need to be kicked off
through a START Signal. This signal needs to be sent at the right
time and requests in some cases to keep track of the pipeline
status (eg: whether pipeline registers are flushed AND output WB
buffers are ready, in case of WB interface).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI and WB interfaces need a more complex pipeline configuration
than the current mdp5_ctl_set_intf().
For example, memory output connections need to be selected for
WB. Interface mode (Video vs. Command modes) also need to be
configured for DSI.
This change takes care of configuring the whole pipeline as far
as operation mode goes. DSI and WB interfaces will be added
later.
v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[Remove temp bisectability hack -Rob]
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_ctl_set_intf()'s second argument should be "int", not "enum mdp5_intf".
The passed in value is "intf", not "intf_id".
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For example, use 'struct mdp5_smp *' everywhere instead of 'void *', but
only declare it as 'struct mdp5_smp;' in common headers, so the struct
body is still private. The accomplishes the desired modularity while
still letting the compiler provide some type checking for us.
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 currently support one single CRTC with its private pipe.
This change allows the configuration of multiple CRTCs with
the possibility to attach several public planes to these CRTCs.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
