Pull networking fixes from David Miller:
1) Don't get per-cpu pointer with preemption enabled in nft_set_pipapo,
fix from Stefano Brivio.
2) Fix memory leak in ctnetlink, from Pablo Neira Ayuso.
3) Multiple definitions of MPTCP_PM_MAX_ADDR, from Geliang Tang.
4) Accidently disabling NAPI in non-error paths of macb_open(), from
Charles Keepax.
5) Fix races between alx_stop and alx_remove, from Zekun Shen.
6) We forget to re-enable SRIOV during resume in bnxt_en driver, from
Michael Chan.
7) Fix memory leak in ipv6_mc_destroy_dev(), from Wang Hai.
8) rxtx stats use wrong index in mvpp2 driver, from Sven Auhagen.
9) Fix memory leak in mptcp_subflow_create_socket error path, from Wei
Yongjun.
10) We should not adjust the TCP window advertised when sending dup acks
in non-SACK mode, because it won't be counted as a dup by the sender
if the window size changes. From Eric Dumazet.
11) Destroy the right number of queues during remove in mvpp2 driver,
from Sven Auhagen.
12) Various WOL and PM fixes to e1000 driver, from Chen Yu, Vaibhav
Gupta, and Arnd Bergmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (35 commits)
e1000e: fix unused-function warning
e1000: use generic power management
e1000e: Do not wake up the system via WOL if device wakeup is disabled
lan743x: add MODULE_DEVICE_TABLE for module loading alias
mlxsw: spectrum: Adjust headroom buffers for 8x ports
bareudp: Fixed configuration to avoid having garbage values
mvpp2: remove module bugfix
tcp: grow window for OOO packets only for SACK flows
mptcp: fix memory leak in mptcp_subflow_create_socket()
netfilter: flowtable: Make nf_flow_table_offload_add/del_cb inline
net/sched: act_ct: Make tcf_ct_flow_table_restore_skb inline
net: dsa: sja1105: fix PTP timestamping with large tc-taprio cycles
mvpp2: ethtool rxtx stats fix
MAINTAINERS: switch to my private email for Renesas Ethernet drivers
rocker: fix incorrect error handling in dma_rings_init
test_objagg: Fix potential memory leak in error handling
net: ethernet: mtk-star-emac: simplify interrupt handling
mld: fix memory leak in ipv6_mc_destroy_dev()
bnxt_en: Return from timer if interface is not in open state.
bnxt_en: Fix AER reset logic on 57500 chips.
...
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2020-06-16
This series contains fixes to e1000 and e1000e.
Chen fixes an e1000e issue where systems could be waken via WoL, even
though the user has disabled the wakeup bit via sysfs.
Vaibhav Gupta updates the e1000 driver to clean up the legacy Power
Management hooks.
Arnd Bergmann cleans up the inconsistent use CONFIG_PM_SLEEP
preprocessor tags, which also resolves the compiler warnings about the
possibility of unused structure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_PM_SLEEP #ifdef checks in this file are inconsistent,
leading to a warning about sometimes unused function:
drivers/net/ethernet/intel/e1000e/netdev.c:137:13: error: unused function 'e1000e_check_me' [-Werror,-Wunused-function]
Rather than adding more #ifdefs, just remove them completely
and mark the PM functions as __maybe_unused to let the compiler
work it out on it own.
Fixes: e086ba2fcc ("e1000e: disable s0ix entry and exit flows for ME systems")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let PCI
core handle the work.
e1000_suspend() calls __e1000_shutdown() to perform intermediate tasks.
__e1000_shutdown() modifies the value of "wake" (device should be wakeup
enabled or not), responsible for controlling the flow of legacy PM.
Since, PCI core has no idea about the value of "wake", new code for generic
PM may produce unexpected results. Thus, use "device_set_wakeup_enable()"
to wakeup-enable the device accordingly.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the system will be woken up via WOL(Wake On LAN) even if the
device wakeup ability has been disabled via sysfs:
cat /sys/devices/pci0000:00/0000:00:1f.6/power/wakeup
disabled
The system should not be woken up if the user has explicitly
disabled the wake up ability for this device.
This patch clears the WOL ability of this network device if the
user has disabled the wake up ability in sysfs.
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver")
Reported-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without a MODULE_DEVICE_TABLE the attributes are missing that create
an alias for auto-loading the module in userspace via hotplug.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port's headroom buffers are used to store packets while they
traverse the device's pipeline and also to store packets that are egress
mirrored.
On Spectrum-3, ports with eight lanes use two headroom buffers between
which the configured headroom size is split.
In order to prevent packet loss, multiply the calculated headroom size
by two for 8x ports.
Fixes: da382875c6 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code to initialize the conf structure while gathering the configuration
of the device was missing.
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Martin <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remove function does not destroy all
BM Pools when per cpu pool is active.
When reloading the mvpp2 as a module the BM Pools
are still active in hardware and due to the bug
have twice the size now old + new.
This eventually leads to a kernel crash.
v2:
* add Fixes tag
Fixes: 7d04b0b13b ("mvpp2: percpu buffers")
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://github.com/KSPP/linux/issues/21
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
It isn't actually described clearly at all in UM10944.pdf, but on TX of
a management frame (such as PTP), this needs to happen:
- The destination MAC address (i.e. 01-80-c2-00-00-0e), along with the
desired destination port, need to be installed in one of the 4
management slots of the switch, over SPI.
- The host can poll over SPI for that management slot's ENFPORT field.
That gets unset when the switch has matched the slot to the frame.
And therein lies the problem. ENFPORT does not mean that the packet has
been transmitted. Just that it has been received over the CPU port, and
that the mgmt slot is yet again available.
This is relevant because of what we are doing in sja1105_ptp_txtstamp_skb,
which is called right after sja1105_mgmt_xmit. We are in a hard
real-time deadline, since the hardware only gives us 24 bits of TX
timestamp, so we need to read the full PTP clock to reconstruct it.
Because we're in a hurry (in an attempt to make sure that we have a full
64-bit PTP time which is as close as possible to the actual transmission
time of the frame, to avoid 24-bit wraparounds), first we read the PTP
clock, then we poll for the TX timestamp to become available.
But of course, we don't know for sure that the frame has been
transmitted when we read the full PTP clock. We had assumed that ENFPORT
means it has, but the assumption is incorrect. And while in most
real-life scenarios this has never been caught due to software delays,
nowhere is this fact more obvious than with a tc-taprio offload, where
PTP traffic gets a small timeslot very rarely (example: 1 packet per 10
ms). In that case, we will be reading the PTP clock for timestamp
reconstruction too early (before the packet has been transmitted), and
this renders the reconstruction procedure incorrect (see the assumptions
described in the comments found on function sja1105_tstamp_reconstruct).
So the PTP TX timestamps will be off by 1<<24 clock ticks, or 135 ms
(1 tick is 8 ns).
So fix this case of premature optimization by simply reordering the
sja1105_ptpegr_ts_poll and the sja1105_ptpclkval_read function calls. It
turns out that in practice, the 135 ms hard deadline for PTP timestamp
wraparound is not so hard, since even the most bandwidth-intensive PTP
profiles, such as 802.1AS-2011, have a sync frame interval of 125 ms.
So if we couldn't deliver a timestamp in 135 ms (which we can), we're
toast and have much bigger problems anyway.
Fixes: 47ed985e97 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool rx and tx queue statistics are reporting wrong values.
Fix reading out the correct ones.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rocker_dma_rings_init, the goto blocks in case of errors
caused by the functions rocker_dma_cmd_ring_waits_alloc() and
rocker_dma_ring_create() are incorrect. The patch fixes the
order consistent with cleanup in rocker_dma_rings_fini().
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
During development we tried to make the interrupt handling as fine-grained
as possible with TX and RX interrupts being disabled/enabled independently
and the counter registers reset from workqueue context.
Unfortunately after thorough testing of current mainline, we noticed the
driver has become unstable under heavy load. While this is hard to
reproduce, it's quite consistent in the driver's current form.
This patch proposes to go back to the previous approach of doing all
processing in napi context with all interrupts masked in order to make the
driver usable in mainline linux. This doesn't impact the performance on
pumpkin boards at all and it's in line with what many ethernet drivers do
in mainline linux anyway.
At the same time we're adding a FIXME comment about the need to improve
the interrupt handling.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will avoid many uneccessary error logs when driver or firmware is
in reset.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AER reset should follow the same steps as suspend/resume. We need to
free context memory during AER reset and allocate new context memory
during recovery by calling bnxt_hwrm_func_qcaps(). We also need
to call bnxt_reenable_sriov() to restore the VFs.
Fixes: bae361c54f ("bnxt_en: Improve AER slot reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VFs are enabled, we need to re-configure them during resume because
firmware has been reset while resuming. Otherwise, the VFs won't
work after resume.
Fixes: c16d4ee0e3 ("bnxt_en: Refactor logic to re-enable SRIOV after firmware reset detected.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The separate steps we do in bnxt_resume() can be done more simply by
calling bnxt_hwrm_func_qcaps(). This change will add an extra
__bnxt_hwrm_func_qcaps() call which is needed anyway on older
firmware.
Fixes: f9b69d7f62 ("bnxt_en: Fix suspend/resume path on 57500 chips")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition exist during termination. The path is
alx_stop and then alx_remove. An alx_schedule_link_check could be called
before alx_stop by interrupt handler and invoke alx_link_check later.
Alx_stop frees the napis, and alx_remove cancels any pending works.
If any of the work is scheduled before termination and invoked before
alx_remove, a null-ptr-deref occurs because both expect alx->napis[i].
This patch fix the race condition by moving cancel_work_sync functions
before alx_free_napis inside alx_stop. Because interrupt handler can call
alx_schedule_link_check again, alx_free_irq is moved before
cancel_work_sync calls too.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VNIC driver's "login" command sequence is the final step
in the driver's initialization process with device firmware,
confirming the available device queue resources to be utilized
by the driver. Under high system load, firmware may not respond
to the request in a timely manner or may abort the request. In
such cases, the driver should reattempt the login command
sequence. In case of a device error, the number of retries
is bounded.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change added a disable to NAPI into macb_open, this was
intended to only happen on the error path but accidentally applies
to all paths. This causes NAPI to be disabled on the success path, which
leads to the network to no longer functioning.
Fixes: 014406babc ("net: cadence: macb: disable NAPI on error")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a comment. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow
unregistered mcast packets to pass.
This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
This path was missed by commit 9d1f644727 ("net: ethernet: ti: ale: fix
seeing unreg mcast packets with promisc and allmulti disabled").
Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti().
Fixes: 9d1f644727 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ALE parameters structure is created on stack, so it has to be reset
before passing to cpsw_ale_create() to avoid garbage values.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Ensure that all scheduled work items have completed before continuing
with device removal and after further event scheduling has been
halted. This patch fixes a bug where a scheduled driver reset event
is processed following device removal.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only QMAP endpoints should be configured to find a pad size field
within packet headers. They are found in the first byte of the QMAP
header (and the hardware fills only the 6 bits in that byte that
constitute the pad_len field).
The RMNet driver assumes the pad_len field is valid for received
packets, so we want to ensure the pad_len field is filled in that
case. That driver also assumes the length in the QMAP header
includes the pad bytes.
The RMNet driver does *not* pad the packets it sends, so the pad_len
field can be ignored.
Fix ipa_endpoint_init_hdr_ext() so it only marks the pad field
offset valid for QMAP RX endpoints, and in that case indicates
that the length field in the header includes the pad bytes.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upper two nibbles of the sequencer type were not used for
SDM845, and were assumed to be 0. But for SC7180 they are used, and
so they must be programmed by ipa_endpoint_init_seq(). Fix this bug.
IPA_SEQ_PKT_PROCESS_NO_DEC_NO_UCP_DMAP doesn't have a descriptive
comment, so add one.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The endpoint id assigned to the modem LAN RX endpoint for the SC7180 SoC
is incorrect. The erroneous value might have been copied from SDM845 and
never updated. The correct endpoint id to use for this SoC is 11.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way the mask value is programmed for QMAP RX endpoints was based
on some wrong assumptions about the way metadata containing the QMAP
mux_id value is formatted. The metadata value supplied by the
modem is *not* in QMAP format, and in fact contains the mux_id we
want in its (big endian) low-order byte. That byte must be written
by the IPA into offset 1 of the QMAP header it inserts before the
received packet.
QMAP TX endpoints *do* use a QMAP header as the metadata sent with
each packet. The modem assumes this, and based on that assumes the
mux_id is in the second byte. To match those assumptions we must
program the modem TX (QMAP) endpoint HDR register to indicate the
metadata will be found at offset 0 in the message header.
The previous configuration managed to work, but it was not working
correctly. This patch fixes a bug whose symptom was receipt of
messages containing the wrong QMAP mux_id.
In fixing this, get rid of ipa_rmnet_mux_id_metadata_mask(), which
was more or less defined so there was a separate place to explain
what was happening as we generated the mask value. Instead, put a
longer description of how this works above ipa_endpoint_init_hdr(),
and define the metadata mask to use as a simple constant.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the PCIe link information for our device.
Fixes: 77f972a707 ("ionic: remove support for mgmt device")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2020-06-11
This series contains fixes to the iavf driver.
Brett fixes the supported link speeds in the iavf driver, which was only
able to report speeds that the i40e driver supported and was missing the
speeds supported by the ice driver. In addition, fix how 2.5 and 5.0
GbE speeds are reported.
Alek fixes a enum comparison that was comparing two different enums that
may have different values, so update the comparison to use matching
enums.
Paul increases the time to complete a reset to allow for 128 VFs to
complete a reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't leave "counter" set to an error pointer. Otherwise either it
will lead to an error pointer dereference later in the function or it
leads to an error pointer dereference when we call mlx5_fc_destroy().
Fixes: 07bab95026 ("net/mlx5: E-Switch, Refactor eswitch ingress acl codes")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Clang warns:
drivers/net/ethernet/mellanox/mlx5/core/main.c:1278:6: warning: variable
'err' is used uninitialized whenever 'if' condition is true
[-Wsometimes-uninitialized]
if (!priv->dbg_root) {
^~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/main.c:1303:9: note:
uninitialized use occurs here
return err;
^~~
drivers/net/ethernet/mellanox/mlx5/core/main.c:1278:2: note: remove the
'if' if its condition is always false
if (!priv->dbg_root) {
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/main.c:1259:9: note: initialize
the variable 'err' to silence this warning
int err;
^
= 0
1 warning generated.
The check of returned value of debugfs_create_dir() is wrong because
by the design debugfs failures should never fail the driver and the
check itself was wrong too. The kernel compiled without CONFIG_DEBUG_FS
will return ERR_PTR(-ENODEV) and not NULL as expected.
Fixes: 11f3b84d70 ("net/mlx5: Split mdev init and pci init")
Link: https://github.com/ClangBuiltLinux/linux/issues/1042
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set the ipv6 word fields according to the hardware definitions.
Fixes: ac991b48d4 ("net/mlx5e: CT: Offload established flows")
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current below problems exists.
1. devlink device is registered by mlx5_load_one(). But it is
not unregistered by mlx5_unload_one(). This is incorrect.
2. Above issue leads to,
When mlx5 PCI device is removed, currently devlink device is
unregistered before devlink ports are unregistered in below ladder
diagram.
remove_one()
mlx5_devlink_unregister()
[..]
devlink_unregister() <- ports are still registered!
mlx5_unload_one()
mlx5_unregister_device()
mlx5_remove_device()
mlx5e_remove()
mlx5e_devlink_port_unregister()
devlink_port_unregister()
3. Condition checking for registering and unregister device are not
symmetric either in these routines.
Hence, fix the sequence by having load and unload routines symmetric
and in right order.
i.e.
(a) register devlink device followed by registering devlink ports
(b) unregister devlink ports followed by devlink device
Do this based on boot and cleanup flags instead of different
conditions.
Fixes: c6acd629ee ("net/mlx5e: Add support for devlink-port in non-representors mode")
Fixes: f60f315d33 ("net/mlx5e: Register devlink ports for physical link, PCI PF, VFs")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
While unregistration is in progress, user might be reloading the
interface.
This can race with unregistration in below flow which uses the
resources which are getting disabled by reload flow.
Hence, disable the devlink reloading first when removing the device.
CPU0 CPU1
---- ----
local_pci_remove() devlink_mutex
remove_one() devlink_nl_cmd_reload()
mlx5_unregister_device() devlink_reload()
ops->reload_down()
mlx5_unload_one()
Fixes: 4383cfcc65 ("net/mlx5: Add devlink reload")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Changing RX hash function requires rearranging of RQT internal indexes,
the user isn't exposed to such changes and these changes do not affect
the user configured indirection table. Rebuild RQ table on hfunc change.
Fixes: bdfc028de1 ("net/mlx5e: Fix ethtool RX hash func configuration change")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After an XSK is closed, the relevant structures in the channel are not
zeroed. If an XSK is opened the second time on the same channel without
recreating channels, the stray values in the structures will lead to
incorrect operation of queues, which causes CQE errors, and the new
socket doesn't work at all.
This patch fixes the issue by explicitly zeroing XSK-related structs in
the channel on XSK close. Note that those structs are zeroed on channel
creation, and usually a configuration change (XDP program is set)
happens on XSK open, which leads to recreating channels, so typical XSK
usecases don't suffer from this issue. However, if XSKs are opened and
closed on the same channel without removing the XDP program, this bug
reproduces.
Fixes: db05815b36 ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Variable "in" in dr_create_rc_qp() is allocated with kvzalloc() and
should be freed with kvfree().
Fixes: 297cccebdc ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, in case of fatal error during mlx5_load_one(), we cannot
enter error state until mlx5_load_one() is finished, what can take
several minutes until commands will get timeouts, because these commands
can't be processed due to the fatal error.
Fix it by setting dev->state as MLX5_DEVICE_STATE_INTERNAL_ERROR before
requesting the lock.
Fixes: c1d4d2e92a ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: Shay Drory <shayd@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With an increased number of VFs, it's possible to encounter the following
issue during reset.
iavf b8d4:00:02.0: Hardware reset detected
iavf b8d4:00:02.0: Reset never finished (0)
iavf b8d4:00:02.0: Reset task did not complete, VF disabled
Increase the reset complete wait count to allow for 128 VFs to complete
reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 4ae4916b56 ("i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb
speeds") added the ability for the PF to report 2.5 and 5Gb speeds,
however, the iavf driver does not recognize those speeds as the values were
not added there. Add the proper enums and values so that iavf can properly
deal with those speeds.
Fixes: 4ae4916b56 ("i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb speeds")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Witold Fijalkowski <witoldx.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
adapter->link_speed has type enum virtchnl_link_speed but our comparisons
are against enum iavf_aq_link_speed. Though they are, currently, the same
values, change the comparison to the matching enum virtchnl_link_speed
since that may not always be the case.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Link speeds are communicated over virtchnl using an enum
virtchnl_link_speed. Currently, the highest link speed is 40Gbps which
leaves us unable to reflect some speeds that an ice VF is capable of.
This causes link speed to be misreported on the iavf driver.
Allow for communicating link speeds using Mbps so that the proper speed can
be reported for an ice VF. Moving away from the enum allows us to
communicate future speed changes without requiring a new enum to be added.
In order to support communicating link speeds over virtchnl in Mbps the
following functionality was added:
- Added u32 link_speed_mbps in the iavf_adapter structure.
- Added the macro ADV_LINK_SUPPORT(_a) to determine if the VF
driver supports communicating link speeds in Mbps.
- Added the function iavf_get_vpe_link_status() to fill the
correct link_status in the event_data union based on the
ADV_LINK_SUPPORT(_a) macro.
- Added the function iavf_set_adapter_link_speed_from_vpe()
to determine whether or not to fill the u32 link_speed_mbps or
enum virtchnl_link_speed link_speed field in the iavf_adapter
structure based on the ADV_LINK_SUPPORT(_a) macro.
- Do not free vf_res in iavf_init_get_resources() as vf_res will be
accessed in iavf_get_link_ksettings(); memset to 0 instead. This
memory is subsequently freed in iavf_remove().
Fixes: 7c710869d6 ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We no longer support the mgmt device in the ionic driver,
so remove the device id and related code.
Fixes: b3f064e974 ("ionic: add support for device id 0x1004")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
