If srp_transfer_data fails within ibmvscsis_write_pending, then
the most likely scenario is that the client timed out the op and
removed the TCE mapping. Thus it will loop forever retrying the
op that is pretty much guaranteed to fail forever. A better return
code would be EIO instead of EAGAIN.
Cc: stable@vger.kernel.org
Reported-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bgly@us.ibm.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Now that we disable the display engine by default, we need to re-enable
it for the Hummingbird A31, which already had its display pipeline
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
While we now support the internal display pipeline found on sun6i, it
is possible that we are unable to enable the display for some boards,
due to a lack of drivers for the panels or bridges found on them. If
the display pipeline is enabled, the driver will try to enable, and
possibly screw up the simple framebuffer U-boot had configured.
Disable the display pipeline by default.
Fixes: 6d0e5b70be ("ARM: dts: sun6i: Add device nodes for first
display pipeline")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
MUSB driver now has runtime PM support, but the debugfs driver misses
the PM _get/_put() calls, which could cause MUSB register access
failure.
Cc: stable@vger.kernel.org # 4.9+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hayes Wang says:
====================
r8152: fix autosuspend issue
Avoid rx is split into two parts when runtime suspend occurs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause the rx and make sure the rx fifo is empty when the autosuspend
occurs.
If the rx data comes when the driver is canceling the rx urb, the host
controller would stop getting the data from the device and continue
it after next rx urb is submitted. That is, one continuing data is
split into two different urb buffers. That let the driver take the
data as a rx descriptor, and unexpected behavior happens.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split rtl8152_suspend() into rtl8152_system_suspend() and
rtl8152_rumtime_suspend().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPC4r37 6.4.1 EXTENDED COPY(LID4) states (also applying to LID1 reqs):
A parameter list length of zero specifies that the copy manager shall
not transfer any data or alter any internal state, and this shall not
be considered an error.
This behaviour can be tested using the libiscsi ExtendedCopy.ParamHdr
test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Check for XCOPY header, CSCD descriptor and segment descriptor list
truncation, and respond accordingly.
SPC4r37 6.4.1 EXTENDED COPY(LID4) states (also applying to LID1 reqs):
If the parameter list length causes truncation of the parameter list,
then the copy manager shall transfer no data and shall terminate the
EXTENDED COPY command with CHECK CONDITION status, with the sense key
set to ILLEGAL REQUEST, and the additional sense code set to PARAMETER
LIST LENGTH ERROR.
This behaviour can be tested using the libiscsi ExtendedCopy.ParamHdr
test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
The XCOPY specification in SPC4r37 states that the XCOPY source and
destination device(s) should be derived from the copy source and copy
destination (CSCD) descriptor IDs in the XCOPY segment descriptor.
The CSCD IDs are generally (for block -> block copies), indexes into
the corresponding CSCD descriptor list, e.g.
=================================
EXTENDED COPY Header
=================================
CSCD Descriptor List
- entry 0
+ LU ID <--------------<------------------\
- entry 1 |
+ LU ID <______________<_____________ |
================================= | |
Segment Descriptor List | |
- segment 0 | |
+ src CSCD ID = 0 --------->---------+----/
+ dest CSCD ID = 1 ___________>______|
+ len
+ src lba
+ dest lba
=================================
Currently LIO completely ignores the src and dest CSCD IDs in the
Segment Descriptor List, and instead assumes that the first entry in the
CSCD list corresponds to the source, and the second to the destination.
This commit removes this assumption, by ensuring that the Segment
Descriptor List is parsed prior to processing the CSCD Descriptor List.
CSCD Descriptor List processing is modified to compare the current list
index with the previously obtained src and dest CSCD IDs.
Additionally, XCOPY requests where the src and dest CSCD IDs refer to
the CSCD Descriptor List entry can now be successfully processed.
Fixes: cbf031f ("target: Add support for EXTENDED_COPY copy offload")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=191381
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Ensure that the segment descriptor CSCD descriptor ID values correspond
to CSCD descriptor entries located in the XCOPY command parameter list.
SPC4r37 6.4.6.1 Table 150 specifies this range as 0000h to 07FFh, where
the CSCD descriptor location in the parameter list can be located via:
16 + (id * 32)
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: inserted "; " in the format string of an error message
and also moved a "||" operator from the start of a line to the end
of the previous line ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
target_xcopy_locate_se_dev_e4() is used to locate an se_dev, based on
the WWN provided with the XCOPY request. Remove a couple of unneeded
arguments, and rely on the caller for the src/dst test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Use UNSUPPORTED TARGET DESCRIPTOR TYPE CODE and UNSUPPORTED SEGMENT
DESCRIPTOR TYPE CODE additional sense codes if a descriptor type in an
XCOPY request is not supported, as specified in spc4r37 6.4.5 and 6.4.6.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
spc4r37 6.4.3.5 states:
If the combined length of the CSCD descriptors and segment descriptors
exceeds the allowed value, then the copy manager shall terminate the
command with CHECK CONDITION status, with the sense key set to ILLEGAL
REQUEST, and the additional sense code set to PARAMETER LIST LENGTH
ERROR.
This functionality can be tested using the libiscsi
ExtendedCopy.DescrLimits test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Check the length of the XCOPY request segment descriptor list against
the value advertised via the MAXIMUM SEGMENT DESCRIPTOR COUNT field in
the RECEIVE COPY OPERATING PARAMETERS response.
spc4r37 6.4.3.5 states:
If the number of segment descriptors exceeds the allowed number, the
copy manager shall terminate the command with CHECK CONDITION status,
with the sense key set to ILLEGAL REQUEST, and the additional sense
code set to TOO MANY SEGMENT DESCRIPTORS.
This functionality is testable using the libiscsi
ExtendedCopy.DescrLimits test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
spc4r37 6.4.3.4 states:
If the number of CSCD descriptors exceeds the allowed number, the copy
manager shall terminate the command with CHECK CONDITION status, with
the sense key set to ILLEGAL REQUEST, and the additional sense code
set to TOO MANY TARGET DESCRIPTORS.
LIO currently responds with INVALID FIELD IN PARAMETER LIST, which sees
it fail the libiscsi ExtendedCopy.DescrLimits test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
As defined in http://www.t10.org/lists/asc-num.htm. To be used during
validation of XCOPY target and segment descriptor lists.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Use drm_accurate_vblank_count so we have the full 32 bit to represent
the frame counter and userspace has a simpler way of knowing when the
counter wraps around.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170110134305.26326-3-tomeu.vizoso@collabora.com
The core provides now an ABI to userspace for generation of frame CRCs,
so implement the ->set_crc_source() callback and reuse as much code as
possible with the previous ABI implementation.
When handling the pageflip interrupt, we skip 1 or 2 frames depending on
the HW because they contain wrong values. For the legacy ABI for
generating frame CRCs, this was done in userspace but now that we have a
generic ABI it's better if it's not exposed by the kernel.
v2:
- Leave the legacy implementation in place as the ABI implementation
in the core is incompatible with it.
v3:
- Use the "cooked" vblank counter so we have a whole 32 bits.
- Make sure we don't mess with the state of the legacy CRC capture
ABI implementation.
v4:
- Keep use of get_vblank_counter as in the legacy code, will be
changed in a followup commit.
v5:
- Skip first frame or two as it's known that they contain wrong
data.
- A few fixes suggested by Emil Velikov.
v6:
- Rework programming of the HW registers to preserve previous
behavior.
v7:
- Address whitespace issue.
- Added a comment on why in the implementation of the new ABI we
skip the 1st or 2nd frames.
v9:
- Add stub for intel_crtc_set_crc_source.
v12:
- Rebased.
- Remove stub for intel_crtc_set_crc_source and instead set the
callback to NULL (Jani Nikula).
v15:
- Rebased.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Robert Foss <robert.foss@collabora.com>
irq
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170110134305.26326-2-tomeu.vizoso@collabora.com
Make sockfs_setattr() static as it is not used outside of net/socket.c
This fixes the following GCC warning:
net/socket.c:534:5: warning: no previous prototype for ‘sockfs_setattr’ [-Wmissing-prototypes]
Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only two fixes at this time. The rtlwifi fix is an important one as it
fixes a reported oops and Linus was already asking about it. The
orinoco fix is not tested on a real device, because it's old legacy
hardware and hardly no-one use it, but it should fix a (theoretical)
issue with VMAP_STACK.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYdG+sAAoJEG4XJFUm622bGo0IAJCx6Ibu+EjbfL1KDDiR4TSS
ZuWHkjVHtbSE0itUCws9RXWCBStUsDV/eFlVax7zBk4XiLtmDKHG0Kvb6K+Bm1qy
rOEgmj8Y0mYzuAHR5efgC5LyyxRqKxGeff20TUZYHQ2KcWmfe5hZi0FJpo0gFjp0
1CUZiSAFuiQmaM6mGleSRZndN65m+bSRjM8yfxTC24XqjdfTVzSXo68Cp4gYk/XE
M62gAg0fyk7UPBwBDztmCtARNW2Zr/OGolQp9ohyOxj3iAuazvTpohywA7Fa0vZu
piBwZJGMAy1ZXHgK58qvoq1ej51RNq+ttjQKiXt9YinL/YBIcs+AkvvVzDFjzZk=
=5g7Z
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-01-10' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.10
Only two fixes at this time. The rtlwifi fix is an important one as it
fixes a reported oops and Linus was already asking about it. The
orinoco fix is not tested on a real device, because it's old legacy
hardware and hardly no-one use it, but it should fix a (theoretical)
issue with VMAP_STACK.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in latest drm-next from Dave Airlie to get at all the drm-misc
goodies, specifically:
- dma_fence error state handling rework (Chris needs that for error
recovery)
- crc support locking changes (Tomeu's i915 crc patches need that).
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The driver put a constant buffer of all zeros on the stack and
pointed a scatterlist entry at it. This doesn't work with virtual
stacks. Use ZERO_PAGE instead.
Cc: stable@vger.kernel.org # 4.9 only
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation failed to detect short transfers when
attempting to read the line state, and also, to make things worse,
logged the content of the uninitialised heap transfer buffer.
Fixes: abf492e7b3 ("USB: kl5kusb105: fix DMA buffers on stack")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Previously we checked for iATU unroll support by reading PCIE_ATU_VIEWPORT
even on platforms, e.g., Keystone, that do not have ATU ports. This can
cause bad behavior such as asynchronous external aborts:
OF: PCI: MEM 0x60000000..0x6fffffff -> 0x60000000
Unhandled fault: asynchronous external abort (0x1211) at 0x00000000
pgd = c0003000
[00000000] *pgd=80000800004003, *pmd=00000000
Internal error: : 1211 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-00009-g6ff59d2-dirty #7
Hardware name: Keystone
task: eb878000 task.stack: eb866000
PC is at dw_pcie_setup_rc+0x24/0x380
LR is at ks_pcie_host_init+0x10/0x170
Move the dw_pcie_iatu_unroll_enabled() check so we only call it on
platforms that do not use the ATU. These platforms supply their own
->rd_other_conf() and ->wr_other_conf() methods.
[bhelgaas: changelog]
Fixes: a0601a4705 ("PCI: designware: Add iATU Unroll feature")
Fixes: 416379f9eb ("PCI: designware: Check for iATU unroll support after initializing host")
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
CC: stable@vger.kernel.org # v4.9+
Also update Kconfig help text, explaining things:
Cirrus is obsolete, the hardware was designed in the 90ies
and can't keep up with todays needs. More background:
https://www.kraxel.org/blog/2014/10/qemu-using-cirrus-considered-harmful/
Better alternatives are:
- stdvga (DRM_BOCHS, qemu -vga std, default in qemu 2.2+)
- qxl (DRM_QXL, qemu -vga qxl, works best with spice)
- virtio (VIRTIO_GPU), qemu -vga virtio)
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Changes:
* add myself as maintainer, so patches land in my inbox.
* add virtualization@lists.linux-foundation.org mailing list.
* add drm-qemu git repo.
* flip bochs and qxl status to "Maintained".
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
virtio uses normal ram as backing storage for the framebuffer, so we
should assign the address to new screen_buffer (added by commit
17a7b0b4d9) instead of screen_base.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The VMA is later clipped against the vm_area_struct before insertion of
the faulting PTE so we are free to create the partial view as we desire.
If we use the object as the extents rather than the area, this partial
can then be used for other areas.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170110095633.6612-2-chris@chris-wilson.co.uk
No actual segmentation faults were observed but the coding is
at least inconsistent.
irqreturn_t meson_mmc_irq():
We should not dereference host before checking it.
meson_mmc_irq_thread():
If cmd or mrq are NULL we should not dereference them after
writing a warning.
Fixes: 51c5d8447b MMC: meson: initial support for GX platforms
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Plantronics BT600 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x1" and "cannot get freq at
ep 0x82". This patch adds the USB ID of the BT600 to quirks.c and
avoids those error messages.
Signed-off-by: Dennis Kadioglu <denk@post.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of scheduling the work to handle the initial delayed event, use 1s
delay.
This delay should not be needed, but Optimus/nouveau will fail in a
mysterious way if the delayed event is handled as soon as possible like it
is done in drm_helper_probe_single_connector_modes() in case the poll
was enabled before.
Reverting 339fd36238 would give back the 10 sec (!) delay to handle the
delayed event. Adding 1sec delay to the poll_work is enough to work around
the issue in Optimus setups and gives shorter response on handling the
initial delayed event.
Fixes: 339fd36238 ("drm: drm_probe_helper: Fix output_poll_work scheduling")
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[danvet: Add FIXME to the comment to make it stick out more.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170109143158.21917-1-peter.ujfalusi@ti.com
Declare exynos_drm_crtc_ops structures as const as they are only passed
as an argument to the function exynos_drm_crtc_create. This argument is
of type const struct exynos_drm_crtc_ops *, so exynos_drm_crtc_ops
structures having this property can be declared const.
Done using Coccinelle:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct exynos_drm_crtc_ops i@p={...};
@ok@
position p;
identifier r.i;
@@
exynos_drm_crtc_create(...,&i@p,...)
@bad@
position p!={r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
+const
struct exynos_drm_crtc_ops i;
File size before:
text data bss dec hex filename
5008 280 0 5288 14a8 exynos/exynos5433_drm_decon.o
File size after:
text data bss dec hex filename
5120 176 0 5296 14b0 exynos/exynos5433_drm_decon.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483984493-25284-1-git-send-email-bhumirks@gmail.com
Continue to clean up drmP.h by moving the cache flushing functions into
it's own header file.
Compile-tested only
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170109215649.6860-2-krisman@collabora.co.uk
Notice that this uncovers an issue with the kernel-doc handling of array
arguments, causing the first parameter of drm_clflush_pages() to not
show up in the rst-generated page. A proposed fix is under review in
linux-doc: <http://www.spinics.net/lists/linux-doc/msg42544.html>
Changes since v1:
- Add section to drm-mm.rst.
- Fix kernel-doc style issues.
- s/memory/kernel memory/.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170109215649.6860-1-krisman@collabora.co.uk
Commit cc3f90f063 ("drm/i915/glk: Reuse broxton code for geminilake")
missed a few of occurences of IS_BROXTON() that should have been
coverted to IS_GEN9_LP().
v2: Cite the right commit. (Ander)
Fixes: cc3f90f063 ("drm/i915/glk: Reuse broxton code for geminilake")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Tomasz Lis <tomasz.lis@intel.com> (v1)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483973495-15138-1-git-send-email-ander.conselvan.de.oliveira@intel.com
Rename i915_gem_get_ggtt_size() and i915_gem_get_ggtt_alignment() to
i915_gem_fence_size() and i915_gem_fence_alignment() respectively to
better match usage. Similarly move the pair of functions into
i915_gem_tiling.c next to the fence restrictions.
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170109161613.11881-6-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Restricting the fence to the end of the previous tile-row breaks access
to the final portion of the object. On gen2/3 we employed lazy fencing
to pad out the fence with scratch page to provide access to the tail,
and now we also pad out the object on gen4+ we can apply the same fix.
Fixes: af1a7301c7 ("drm/i915: Only fence tiled region of object.")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170109161613.11881-5-chris@chris-wilson.co.uk
The fence size/alignment is a combination of the vma size plus object
tiling parameters. Those parameters are rarely changed, making the fence
size/alignemnt roughly constant for the lifetime of the VMA. We can
simplify subsequent calculations by precalculating the size/alignment
required for GGTT vma taking fencing into account (with an update if we
do change the tiling or stride).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170109161613.11881-4-chris@chris-wilson.co.uk
