Instead of trying hard to stay connected to the
host, it's best (and far easier) to disconnect from
the host already.
Anything relying on KEEP_CONNECT will just have that
ignored, but we don't have proper hibernation
implementation yet, so there are no regressions.
In any case, hibernation is only useful for runtime
PM, not system sleep.
While at that, also remove dwc3.dcfg which has been
rendered unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be re-using it for suspend/resume, so
instead of duplicating code, let's just re-factor
the functions so they can be re-used.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The PLX USB2380 is a PCIe version of the NET2280 and behaves more like the
USB338x but without the USB3.0 superspeed support.
This was tested with g_ether, g_serial, g_mass_storage on a Gateworks
Ventana GW2383.
Cc: Justin DeFields <justindefields@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With a default size of 16kiB and with maximum of 32
buffers, we can transfer up to 512kiB, however Linux
can transfer up to 1MiB in a single mass storage
block transfer to USB3 storage devices.
Because of this, 1MiB block transfers end up being
slower than 512kiB block transfers. Let's increase
maximum number of storage buffers to a ridiculous
amount (256) so that anybody wanting to test maximum
achievable throughput can do so.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
valid range for storage buffers is encoded in
Kconfig already. Instead of checking again, let's
drop fsg_num_buffers_validate() altogether.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's annoying to constantly see the same "Not yet implemented" message
over and over with nothing able to be done about it, so rate limit it
for now to keep user's logs "clean".
Reported-by: Lars Täuber <lars.taeuber@web.de>
Tested-by: Lars Täuber <lars.taeuber@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB LED driver exposes a undocumented sysfs interface and doesn't
use the standard kernel LED subsystem. It supports three devices:
Delcom Visual Signal Indicator
The driver supports generation 1 of the device only which was
manufactured until 2008. Remove support for this device completely.
Riso Kagaku RGB LED + Dream Cheeky Webmail Notifier
These devices are HID compliant and are supported by a new USB LED
driver under drivers/hid utilizing the kernel LED subsystem.
So let's remove the old USB LED driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The comment is wrong, glue is devm_kzalloc-ed mem attached to the
"allwinner,sun4i-a10-musb" compatible platform-dev. Where as
glue->musb_pdev is a newly created "musb-hdrc" platform-dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop using the return value of platform_device_register_full() to get to
the struct musb in sunxi_musb_work(). If a gadget has been registered
(insmod-ed) before the musb driver, then musb_start will get called
from the musb_core probe function and sunxi_musb_work() may run before
platform_device_register_full() has returned.
Instead store a pointer to struct musb in struct sunxi_glue when
sunxi_musb_enable gets called. Note that sunxi_musb_enable always gets
called before sunxi_musb_work() can run.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix warning about tainted kernel because usb-otg-fsm has no license.
WARNING: with this patch usb-otg-fsm module can be loaded
but then the kernel will hang. Tested with a udoo quad board.
Cc: <stable@vger.kernel.org> #v4.1+
Signed-off-by: Oscar <oscar@naiandei.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Currently the Linux PCI core does not touch power state of PCI bridges and
PCIe ports when system suspend is entered. Leaving them in D0 consumes
power unnecessarily and may prevent the CPU from entering deeper C-states.
With recent PCIe hardware we can power down the ports to save power given
that we take into account few restrictions:
- The PCIe port hardware is recent enough, starting from 2015.
- Devices connected to PCIe ports are effectively in D3cold once the port
is transitioned to D3 (the config space is not accessible anymore and
the link may be powered down).
- Devices behind the PCIe port need to be allowed to transition to D3cold
and back. There is a way both drivers and userspace can forbid this.
- If the device behind the PCIe port is capable of waking the system it
needs to be able to do so from D3cold.
This patch adds a new flag to struct pci_device called 'bridge_d3'. This
flag is set and cleared by the PCI core whenever there is a change in power
management state of any of the devices behind the PCIe port. When system
later on is suspended we only need to check this flag and if it is true
transition the port to D3 otherwise we leave it in D0.
Also provide override mechanism via command line parameter
"pcie_port_pm=[off|force]" that can be used to disable or enable the
feature regardless of the BIOS manufacturing date.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for shared platform controllers by using
devm_reset_control_get_shared_by_index instead of
of_reset_control_get_by_index.
Note we use the devm function because there is no
of_reset_control_get_shared_by_index, this also leads
to a nice cleanup of the cleanup code.
This brings the ehci-platform reset handling code inline
with ohci-platform.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least the EHCI/OHCI found on the Allwinnner H3 SoC needs multiple
reset lines, the controller will not initialize while the reset for
its companion is still asserted, which means we need to de-assert
2 resets for the controller to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to the save power consumption, as a workaround, suspend
forcibly the USB PORTA/B/C via set the SUSPEND_A/B/C bits of OHCI
Interrupt Configuration Register in the SFRs while OHCI USB suspend.
This suspend operation must be done before the USB clock is disabled,
resume after the USB clock is enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver should clean up after itself by unpreparing the clock when it
is unbound.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver supports two paths of device instantiation: as platform and i2c
device. In the platform path it lacks of storing the driver specific
structure as drvdata.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only caller of get_gadget_descs() has already dereferenced udc
before calling this function, so udc can not be NULL at this point of
the code and hence no use of checking it.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Space prohibited before close parenthesis ')'.
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stub_disconnect() calls stub_device_reset() during usb_unbind_device() when
usb device is locked. So usb_lock_device_for_reset() in stub_device_reset()
in that case polls for one second and returns -EBUSY anyway.
Remove useless flag USBIP_EH_RESET from SDEV_EVENT_REMOVED.
Signed-off-by: Alexander Popov <alpopov@ptsecurity.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ehci compatible controllers have more than one reset signal lines,
e.g., Synopsys DWC USB2.0 Host-AHB Controller has two resets hreset_i_n
and phy_rst_i_n. Two more resets are added in this patch in order for
this kind of controller to use this driver directly.
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a suspend/resume issue where the driver is blindly
calling ehci_suspend/resume functions when the ehci hasn't been setup.
This results in a crash during suspend/resume operations.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Pramod Gurav <pramod.gurav@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with commit 0b52297f22 ("reset: Add support for shared reset
controls") there is a reference count for reset control assertions. The
goal is to allow resets to be shared by multiple devices and an assert
will take effect only when all instances have asserted the reset.
In order to preserve backwards-compatibility, all reset controls become
exclusive by default. This is to ensure that reset_control_assert() can
immediately assert in hardware.
However, this new behaviour triggers the following warning in the EHCI
driver for Tegra:
[ 3.365019] ------------[ cut here ]------------
[ 3.369639] WARNING: CPU: 0 PID: 1 at drivers/reset/core.c:187 __of_reset_control_get+0x16c/0x23c
[ 3.382151] Modules linked in:
[ 3.385214] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.6.0-rc6-next-20160503 #140
[ 3.392769] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[ 3.399046] [<c010fa50>] (unwind_backtrace) from [<c010b120>] (show_stack+0x10/0x14)
[ 3.406787] [<c010b120>] (show_stack) from [<c0347dcc>] (dump_stack+0x90/0xa4)
[ 3.414007] [<c0347dcc>] (dump_stack) from [<c011f4fc>] (__warn+0xe8/0x100)
[ 3.420964] [<c011f4fc>] (__warn) from [<c011f5c4>] (warn_slowpath_null+0x20/0x28)
[ 3.428525] [<c011f5c4>] (warn_slowpath_null) from [<c03cc8cc>] (__of_reset_control_get+0x16c/0x23c)
[ 3.437648] [<c03cc8cc>] (__of_reset_control_get) from [<c0526858>] (tegra_ehci_probe+0x394/0x518)
[ 3.446600] [<c0526858>] (tegra_ehci_probe) from [<c04516d8>] (platform_drv_probe+0x4c/0xb0)
[ 3.455029] [<c04516d8>] (platform_drv_probe) from [<c044fe78>] (driver_probe_device+0x1ec/0x330)
[ 3.463892] [<c044fe78>] (driver_probe_device) from [<c0450074>] (__driver_attach+0xb8/0xbc)
[ 3.472320] [<c0450074>] (__driver_attach) from [<c044e1ec>] (bus_for_each_dev+0x68/0x9c)
[ 3.480489] [<c044e1ec>] (bus_for_each_dev) from [<c044f338>] (bus_add_driver+0x1a0/0x218)
[ 3.488743] [<c044f338>] (bus_add_driver) from [<c0450768>] (driver_register+0x78/0xf8)
[ 3.496738] [<c0450768>] (driver_register) from [<c010178c>] (do_one_initcall+0x40/0x170)
[ 3.504909] [<c010178c>] (do_one_initcall) from [<c0c00ddc>] (kernel_init_freeable+0x158/0x1f8)
[ 3.513600] [<c0c00ddc>] (kernel_init_freeable) from [<c0810784>] (kernel_init+0x8/0x114)
[ 3.521770] [<c0810784>] (kernel_init) from [<c0107778>] (ret_from_fork+0x14/0x3c)
[ 3.529361] ---[ end trace 4bda87dbe4ecef8a ]---
The reason is that Tegra SoCs have three EHCI controllers, each with a
separate reset line. However the first controller contains UTMI pads
configuration registers that are shared with its siblings and that are
reset as part of the first controller's reset. There is special code in
the driver to assert and deassert this shared reset at probe time, and
it does so irrespective of which controller is probed first to ensure
that these shared registers are reset before any of the controllers are
initialized. Unfortunately this means that if the first controller gets
probed first, it will request its own reset line and will subsequently
request the same reset line again (temporarily) to perform the reset.
This used to work fine before the above-mentioned commit, but now
triggers the new WARN.
Work around this by making sure we reuse the controller's reset if the
controller happens to be the first controller.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.
Commit a47cc24cd1 ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.
This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.
Fixes: a47cc24cd1 ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parport subsystem has introduced parport_del_port() to delete a port
when it is going away. Without parport_del_port() the registered port
will not be unregistered.
To reproduce and verify the error:
Command to be used is : ls /sys/bus/parport/devices
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and the command still shows "parport0".
4) Attach the device again and we get "parport1".
With the patch applied:
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and there is no output as "parport0" is now
removed.
4) Attach device again to get "parport0" again.
Cc: <stable@vger.kernel.org> # 4.2+
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.
This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.
The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.
Fix ed_schedule to update ED state only on successful return.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds support for the Araneus Alea I USB hardware Random Number
Generator which is interfaced with in exactly the same way as the
Altus Metrum ChaosKey. We just add the appropriate device ID and
modify the config help text.
Signed-off-by: Bob Ham <bob.ham@collabora.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
shared_fifo endpoints would only get a previous tx state cleared
out, the rx state was only cleared for non shared_fifo endpoints
Change this so that the rx state is cleared for all endpoints.
This addresses an issue that resulted in rx packets being dropped
silently.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Incorrect cppi dma channel is referenced in musb_rx_dma_iso_cppi41(),
which causes kernel NULL pointer reference oops later when calling
cppi41_dma_channel_program().
Fixes: 069a3fd (usb: musb: Remove ifdefs for musb_host_rx in musb_host.c
part1)
Cc: <stable@vger.kernel.org> # v4.2+
Reported-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the session bit was not set in the backup of devctl register,
restoring devctl would clear the session bit. Therefor, only restore
devctl register when the session bit was set in the backup.
This solves the device enumeration failure in otg mode exposed by commit
56f487c (PM / Runtime: Update last_busy in rpm_resume).
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to check the state for the PHY with delayed_work
as otherwise MUSB will get confused and idles immediately.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no longer any need for custom initcall level for
musb.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the pull up being handled with delayed work, we can
now finally remove pm_runtime_set_irq_safe that blocks the
MUSB glue from idling.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With PM runtime behaving, these are all now unnecessary.
Doing pm_runtime_get(musb->controller) will keep the parent
glue layer also active.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least on n900 we have phy-twl4030-usb only generating cable
interrupts, and then have a separate USB PHY.
In order for musb to know the real cable status, we need to
clear any cached state until musb is ready. Otherwise the cable
status interrupts will get just ignored if the status does
not change from the initial state.
To do this, let's add a return value to musb_mailbox(), and
reset cached linkstat to MUSB_UNKNOWN on error. Sorry to cause
a bit of churn here, I should have added that already last time
patching musb_mailbox().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least 2430 glue layer pulls d+ high on start up even if there are
no gadgets configured. This is bad at least for anything using a separate
battery charger chip as it can confuse the charger detection.
Let's fix the issue by removing the bogus glue layer code tinkering
with the SESSION bit. As pointed out Bin Liu <b-liu@ti.com> and
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>, the SESSION
bit just starts host mode if ID pin is grounded, and starts the
srp is ID pin is floating. So without the ID pin changing, it's
unable to force musb mode to anything. And just for starting a
host mode, things work fine without this code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is no longer needed with PM runtime at least for 2430 glue.
We can now rely only on PM runtime and cable detection.
The other glue layers can probably remove try_idle too, but that
needs to be tested for each platform before doing it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This simplifies things and allows idling both MUSB and PHY
when nothing is configured. Let's just return early from PM
runtime if musb is not yet initialized.
Let's also warn if PHY is not configured.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may have drivers loaded but no configured gadgets and MUSB may be in
host mode. If gadgets are configured during host mode, PM runtime will
get confused.
Disable PM runtime from gadget state, and do it based on the cable
and last state.
Note that we may get multiple cable events, so we need to keep track
of the power state.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have MUSB setting pm_runtime_irq_safe with the following
commits:
30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel panic")
3e43a07256 ("usb: musb: core: add pm_runtime_irq_safe()")
Let's fix things to use delayed work so we can remove the
pm_runtime_irq_safe.
Note that we may want to set this up in a generic way in the
gadget framework eventually.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conditional use of PM runtime does not work properly
for musb gadget. On cable disconnect we may not get any
USB_EVENT_NONE leaving the PM runtime call unpaired.
Let's fix the issue by making sure the PM runtime calls are
paired within the functions. The glue layer will take care
of the rest.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's not tinker with the PM runtime of musb core from the omap2430
wrapper. This allows us to initialize PM runtime for musb core later
on instead of doing it in stages. And omap2430 wrapper has no need
to for accessing musb core at this point.
Note that this does not remove all the PM runtime calls from the
glue layer, those will get removed in a later patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's make the PM runtime use the standard autosuspend calls.
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") means we must pair use_autosuspend with
dont_use_autosuspend and then use put_sync to properly idle the
device.
Note that we'll be removing the PM runtime calls from the glue
layer to the MUSB core in the next patch. And we can also remove
the pointless FIXME comment now.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have remove() already calling shutdown(), so let's drop it
and move the code to remove(). No code changes, we'll drop the
the FIXME in the following patch with more clean-up.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like at least 2430 glue won't idle reliably with the 200 ms
autosuspend delay. This causes deeper idle states being blocked for
the whole SoC when disconnecting OTG A cable.
Increasing the delay to 500 ms seems to idle both MUSB and the PHY
reliably. This is probably because of time needed by the hardware
based negotiation between MUSB and the PHY.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the board is powering attached usb devices via the otg port
sometimes / on some devices it takes slightly too long for the Vbus
detection code in phy-sun4i-usb.c to signal that Vbus is high after
enabling Vbus and the musb hardware signals a MUSB_INTR_VBUSERROR
interrupt.
This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
VBUSERROR interrupts, fixing connection issues in these cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the mode handling to the platform_set_mode callback.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the DMA engine check was moved to musb_tx_dma_porgram(), both
musb_tx_dma_set_mode_cppi_tusb() and musb_tx_dma_set_mode_mentor() always
return 0, so we can make both these functions *void*.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
looks incomplete: the DMA engine checks are done outside the Mentor/UX500
handler but inside the CPPI/TUSB handler. Move the checks out of the CPPI/
TUSB handler into its caller, musb_tx_dma_program().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
urb->status is set when endpoint csr RXSTALL, H_ERROR, DATAERROR or
INCOMPRX bit is set. Those bits mean a broken pipe, so don't start next
urb when any of these bits is set by checking urb->status.
To minimize the risk of regression, only do so for RX, until we have a
test case to understand the behavior of TX.
The patch fixes system freeze issue caused by repeatedly invoking RX ISR
while removing a usb uart device connected to a hub, in which case the
hub has no chance to report the disconnect event due to the kernel is
busy in processing the RX interrupt flooding.
Fix checkpatch complaint (qh != NULL) as while.
Reported-by: Max Uvarov <muvarov@gmail.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUSB Programming Guide states that the driver should clear RXCSR
bit2 when the controller sets the bit.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.
Tests on another motherboard show that it does work with streams disabled.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several people have reported that UBSAN doesn't like the pointer
arithmetic in ehci_hub_control():
u32 __iomem *status_reg = &ehci->regs->port_status[
(wIndex & 0xff) - 1];
u32 __iomem *hostpc_reg = &ehci->regs->hostpc[(wIndex & 0xff) - 1];
If wIndex is 0 (and it often is), these calculations underflow and
UBSAN complains.
According to the C standard, pointer computations leading to locations
outside the bounds of an array object (other than 1 position past the
end) are undefined. In this case, the compiler would be justified in
concluding the wIndex can never be 0 and then optimizing away the
tests for !wIndex that occur later in the subroutine. (Although,
since ehci->regs->port_status and ehci->regs->hostpc are both 0-length
arrays and are thus GCC extensions to the C standard, it's not clear
what the compiler is really allowed to do.)
At any rate, we can avoid all these difficulties, at the cost of
making the code slightly longer, by not decrementing the index when it
is equal to 0. The runtime effect is minimal, and anyway
ehci_hub_control() is not on a hot path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Martin_MOKREJÅ <mmokrejs@gmail.com>
Reported-by: "Navin P.S" <navinp1912@gmail.com>
CC: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 198de51dbc ("USB: uas: Limit qdepth at the scsi-host level")
removed the scsi_change_queue_depth() call from uas_slave_configure()
assuming that the slave would inherit the host's queue_depth, which
that commit sets to the same value.
This is incorrect, without the scsi_change_queue_depth() call the slave's
queue_depth defaults to 1, introducing a performance regression.
This commit restores the call, fixing the performance regression.
Cc: stable@vger.kernel.org
Fixes: 198de51dbc ("USB: uas: Limit qdepth at the scsi-host level")
Reported-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 198de51dbc ("USB: uas: Limit qdepth at the scsi-host level") made
qdepth limit set in host template (`.can_queue = MAX_CMNDS`) redundant.
Removing it to avoid confusion.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Acer C120 LED Projector is a USB-3 connected pico projector which
takes both its power and video data from USB-3.
In combination with some hubs this device does not play well with
lpm, so disable lpm for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly sort all the entries by vendor id.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1c127ae99 ("usb: host: xhci: plat: make use of new methods in
xhci_plat_priv") sets xhci->quirks before calling xhci_gen_setup(), which
will overwrite them.
Don't overwite the quirks, just add the new ones
Fixes: b1c127ae99 ("usb: host: xhci: plat: make use of new methods in xhci_plat_priv")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platforms, the clocks might be registered by a platform
driver. When this is the case, the clock platform driver may very well
be probed after xhci-plat, in which case the first probe() invocation
of xhci-plat will receive -EPROBE_DEFER as the return value of
devm_clk_get().
The current code handles that as a normal error, and simply assumes
that this means that the system doesn't have a clock for the XHCI
controller, and continues probing without calling
clk_prepare_enable(). Unfortunately, this doesn't work on systems
where the XHCI controller does have a clock, but that clock is
provided by another platform driver. In order to fix this situation,
we handle the -EPROBE_DEFER error condition specially, and abort the
XHCI controller probe(). It will be retried later automatically, the
clock will be available, devm_clk_get() will succeed, and the probe()
will continue with the clock prepared and enabled as expected.
In practice, such issue is seen on the ARM64 Marvell 7K/8K platform,
where the clocks are registered by a platform driver.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.
If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.
There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.
The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.
Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.
Cc: stable <stable@vger.kernel.org>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove. This means that instead of returning, we end up
handling this interruption in the middle of a shutdown. Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.
commit 8c24d6d7b0 ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device. Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path. The code flow for this oops looks like
this:
xhci_pci_remove()
usb_remove_hcd(xhci->shared)
xhci_stop(xhci->shared)
xhci_halt()
xhci_mem_cleanup(xhci); // Free the event_queue
usb_hcd_pci_remove(primary)
xhci_irq() // Access the event_queue if STS_EINT is set. Crash.
xhci_stop()
xhci_halt()
// return early
The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD. This way, we still have the event_queue configured
when invoking xhci_irq. We still halt the device on the first call to
xhci_stop, though.
I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.
[ 113.334124] Unable to handle kernel paging request for data at address 0x00000028
[ 113.335514] Faulting instruction address: 0xd00000000d4f767c
[ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV
[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Cc: stable@vger.kernel.org
Reviewed-by: Roger Quadros <rogerq@ti.com>
Cc: <stable@vger.kernel.org> #v4.3+
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of core revision 2.60a the recommended programming model is to set
the ClearPendIN bit when issuing a Clear Stall EP command for IN
endpoints. This is to prevent an issue where some (non-compliant) hosts
may not send ACK TPs for pending IN transfers due to a mishandled error
condition. Synopsys STAR 9000614252.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set USB3_FORCE_VBUSVALID when configured for USB_DR_MODE_PERIPHERAL
mode, as it is required to have a working setup.
This worked on the internal driver by relying on the reset
value of the syscfg register as the bits aren't explicity cleared
and set like the upstream driver.
Also add a comment about what setting this bit means.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In OS descriptors handling, if ctrl->bRequestType is
USB_RECIP_DEVICE and w_index != 0x4 or (w_value >> 8)
is true, it will not assign a valid value to req->length,
but use the default value(-EOPNOTSUPP), and queue an
OS desc request with the invalid req->length. It always
happens on the platforms which use os_desc (for example:
rk3366, rk3399), and cause kernel panic as follows
(use dwc3 driver):
Unable to handle kernel paging request at virtual address ffffffc0f7e00000
Internal error: Oops: 96000146 [#1] PREEMPT SMP
PC is at __dma_clean_range+0x18/0x30
LR is at __swiotlb_map_page+0x50/0x64
Call trace:
[<ffffffc0000930f8>] __dma_clean_range+0x18/0x30
[<ffffffc00062214c>] usb_gadget_map_request+0x134/0x1b0
[<ffffffc0005c289c>] __dwc3_ep0_do_control_data+0x110/0x14c
[<ffffffc0005c2d38>] __dwc3_gadget_ep0_queue+0x198/0x1b8
[<ffffffc0005c2e18>] dwc3_gadget_ep0_queue+0xc0/0xe8
[<ffffffc00061cfec>] composite_ep0_queue.constprop.14+0x34/0x98
[<ffffffc00061dfb0>] composite_setup+0xf60/0x100c
[<ffffffc0006204dc>] android_setup+0xd8/0x138
[<ffffffc0005c29a4>] dwc3_ep0_delegate_req+0x34/0x50
[<ffffffc0005c3534>] dwc3_ep0_interrupt+0x5dc/0xb58
[<ffffffc0005c0c3c>] dwc3_thread_interrupt+0x15c/0xa24
With this patch, the gadget driver will not queue
a request and return immediately if req->length is
invalid. And the usb controller driver can handle
the unsupport request correctly.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If c->cdev->use_os_string flag is not set,
don't need to invoke ffs_do_os_descs() in _ffs_func_bind.
So uninitialized ext_compat_id pointer won't be accessed by
__ffs_func_bind_do_os_desc to cause kernel panic.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit dc8c46a5ae ("usb: gadget: f_tcm: convert to new function
interface with backward compatibility") introduced a possible out
of bounds memory access:
If tpg is not found in function usbg_drop_tpg,
tpg_instances[TPG_INSTANCES] is accessed.
Fixes: dc8c46a5ae ("usb: gadget: f_tcm: convert to new function interface with backward compatibility")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Function in_rq_cur copies random bytes from the stack.
Zero the memory instead.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A patch that went into Linux-4.4 to fix big-endian mode on a Lantiq
MIPS system unfortunately broke big-endian operation on PowerPC
APM82181 as reported by Christian Lamparter, and likely other
systems.
It actually introduced multiple issues:
- it broke big-endian ARM kernels: any machine that was working
correctly with a little-endian kernel is no longer using byteswaps
on big-endian kernels, which clearly breaks them.
- On PowerPC the same thing must be true: if it was working before,
using big-endian kernels is now broken. Unlike ARM, 32-bit PowerPC
usually uses big-endian kernels, so they are likely all broken.
- The barrier for dwc2_writel is on the wrong side of the __raw_writel(),
so the MMIO no longer synchronizes with DMA operations.
- On architectures that require specific CPU instructions for MMIO
access, using the __raw_ variant may turn this into a pointer
dereference that does not have the same effect as the readl/writel.
This patch is a simple revert for all architectures other than MIPS,
in the hope that we can more easily backport it to fix the regression
on PowerPC and ARM systems without breaking the Lantiq system again.
We should follow this up with a more elaborate change to add runtime
detection of endianness, to make sure it also works on all other
combinations of architectures and implementations of the usb-dwc2
device. That patch however will be fairly large and not appropriate
for backports to stable kernels.
Felipe suggested a different approach, using an endianness switching
register to always put the device into LE mode, but unfortunately
the dwc2 hardware does not provide a generic way to do that. Also,
I see no practical way of addressing the problem more generally by
patching architecture specific code on MIPS.
Fixes: 95c8bc3609 ("usb: dwc2: Use platform endianness when accessing registers")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Current __ffs_data_do_os_desc() of f_fs.c will check reserved1 field
of OS_DESC_EXT_COMPAT and return -EINVAL if it's 1.
But MS OS 1.0 Descriptors
http://msdn.microsoft.com/en-us/library/windows/hardware/gg463179.aspx
defines that field to be 1.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Device qualifier descriptor is now generated by composite.c
code. So let's fix this old comment by removing parts which
are no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Krzysztof Opasiak <kopasiak90@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This descriptor is never used. Currently device qualifier
descriptor is generated by compossite code so no need to
keep it in function file.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Krzysztof Opasiak <kopasiak90@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This descriptor is never used. Currently device qualifier
descriptor is generated by compossite code, so no need to
keep it in function file.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Krzysztof Opasiak <kopasiak90@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a check in dwc2_hsotg_ep_sethalt() so that it does not halt
isochronous endpoints.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget API function usb_ep_set_halt() expects the gadget to return
-EAGAIN if the ep is active. Add support for this behavior.
Otherwise this may break mass storage protocol if a STALL is attempted
on the endpoint.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This loop is supposed to set all the .num[] values to -1 but it's off by
one so it skips the first element and sets one element past the end of
the array.
I've cleaned up the loop a little as well.
Fixes: ddf8abd259 ('USB: f_fs: the FunctionFS driver')
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3-exynos has two problems during init if the regulators are slow
to come up (for instance if the I2C bus driver is not on the initramfs)
and return probe deferral. First, every time this happens, the driver
leaks the USB phys created; they need to be deallocated on error.
Second, since the phy devices are created before the regulators fail,
this means that there's a new device to re-trigger deferred probing,
which causes it to essentially go into a busy loop of re-probing the
device until the regulators come up.
Move the phy creation to after the regulators have succeeded, and also
fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs
which doesn't contain the I2C driver), this reduces the number of probe
attempts (for each of the two controllers) from more than 2000 to eight.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Fixes: d720f057fd ("usb: dwc3: exynos: add nop transceiver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By default user could store only valid UDC name in configfs UDC
attr by doing:
echo $UDC_NAME > UDC
Commit (855ed04 "usb: gadget: udc-core: independent registration of
gadgets and gadget drivers") broke this behavior and allowed to store
any arbitrary string in UDC file and udc core was waiting for such
controller to appear.
echo "any arbitrary string here" > UDC
This commit fix this by adding a flag which prevents configfs
gadget from being added to list of pending drivers if UDC with
given name has not been found.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the outstanding target pending updates for v4.7-rc1.
The highlights this round include:
- Allow external PR/ALUA metadata path be defined at runtime via top
level configfs attribute (Lee)
- Fix target session shutdown bug for ib_srpt multi-channel (hch)
- Make TFO close_session() and shutdown_session() optional (hch)
- Drop se_sess->sess_kref + convert tcm_qla2xxx to internal kref
(hch)
- Add tcm_qla2xxx endpoint attribute for basic FC jammer (Laurence)
- Refactor iscsi-target RX/TX PDU encode/decode into common code
(Varun)
- Extend iscsit_transport with xmit_pdu, release_cmd, get_rx_pdu,
validate_parameters, and get_r2t_ttt for generic ISO offload
(Varun)
- Initial merge of cxgb iscsi-segment offload target driver (Varun)
The bulk of the changes are Chelsio's new driver, along with a number
of iscsi-target common code improvements made by Varun + Co along the
way"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (29 commits)
iscsi-target: Fix early sk_data_ready LOGIN_FLAGS_READY race
cxgbit: Use type ISCSI_CXGBIT + cxgbit tpg_np attribute
iscsi-target: Convert transport drivers to signal rdma_shutdown
iscsi-target: Make iscsi_tpg_np driver show/store use generic code
tcm_qla2xxx Add SCSI command jammer/discard capability
iscsi-target: graceful disconnect on invalid mapping to iovec
target: need_to_release is always false, remove redundant check and kfree
target: remove sess_kref and ->shutdown_session
iscsi-target: remove usage of ->shutdown_session
tcm_qla2xxx: introduce a private sess_kref
target: make close_session optional
target: make ->shutdown_session optional
target: remove acl_stop
target: consolidate and fix session shutdown
cxgbit: add files for cxgbit.ko
iscsi-target: export symbols
iscsi-target: call complete on conn_logout_comp
iscsi-target: clear tx_thread_active
iscsi-target: add new offload transport type
iscsi-target: use conn_transport->transport_type in text rsp
...
Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of other
stuff.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0P8ACgkQMUfUDdst+ykkFQCg0kJlxIiCU1FYBZYriqo4vX3F
9N8AoM/8nO8Y6vMpF2LWnamafYgqscTE
=ZuCh
-----END PGP SIGNATURE-----
Merge tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of
other stuff.
All have been in linux-next with no reported issues"
* tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (164 commits)
USB: serial: ti_usb_3410_5052: add MOXA UPORT 11x0 support
USB: serial: fix minor-number allocation
USB: serial: quatech2: fix use-after-free in probe error path
USB: serial: mxuport: fix use-after-free in probe error path
USB: serial: keyspan: fix debug and error messages
USB: serial: keyspan: fix URB unlink
USB: serial: keyspan: fix use-after-free in probe error path
USB: serial: io_edgeport: fix memory leaks in probe error path
USB: serial: io_edgeport: fix memory leaks in attach error path
usb: Remove unnecessary space before operator ','.
usb: Remove unnecessary space before open square bracket.
USB: FHCI: avoid redundant condition
usb: host: xhci-rcar: Avoid long wait in xhci_reset()
usb/host/fotg210: remove dead code in create_sysfs_files
usb: wusbcore: Do not initialise statics to 0.
usb: wusbcore: Remove space before ',' and '(' .
USB: serial: cp210x: clean up CRTSCTS flag code
USB: serial: cp210x: get rid of magic numbers in CRTSCTS flag code
USB: serial: cp210x: fix hardware flow-control disable
USB: serial: option: add even more ZTE device ids
...
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
This patch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas) there's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJXO8W0AAoJEDeqqVYsXL0MW24H/jGWwfjsDUiSsLwbLca6DWu8
ZCWZ7rSZ27CApwGPgZGpLvUg+vpW8Ykm2zdeBnlZ6ScXS+dT3uo/PHsnemsTextj
6glQNIOFY0Ja2GwkkN00M6IZQhTJ628cqJKIEJxC68lIw16wiOwjZaK68GMrusDO
Sl062rkuLR6Jb2T+YoT/sD8jQfWlSj2V9e9rqJoS/rIbS6B+hUipuybz2yQ2yK2u
XFc30yal9oVz1fHEoh2O8aqckW3/iskukVXVuZ0MQzT/lV/bm9I6AnWVHw7d0Yhp
ZELjXpjx5M2Z/d8k0Wvx1e25oL/ERwa96yLnTvRcqyF5Yt1EgAhT+jKvo4pnGr8=
=L6y/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"First round of SCSI updates for the 4.6+ merge window.
This batch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas). There's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (138 commits)
mpt3sas: Used "synchronize_irq()"API to synchronize timed-out IO & TMs
mpt3sas: Set maximum transfer length per IO to 4MB for VDs
mpt3sas: Updating mpt3sas driver version to 13.100.00.00
mpt3sas: Fix initial Reference tag field for 4K PI drives.
mpt3sas: Handle active cable exception event
mpt3sas: Update MPI header to 2.00.42
Revert "lpfc: Delete unnecessary checks before the function call mempool_destroy"
eata_pio: missing break statement
hpsa: Fix type ZBC conditional checks
scsi_lib: Decode T10 vendor IDs
scsi_dh_alua: do not fail for unknown VPD identification
scsi_debug: use locally assigned naa
scsi_debug: uuid for lu name
scsi_debug: vpd and mode page work
scsi_debug: add multiple queue support
bfa: fix bfa_fcb_itnim_alloc() error handling
megaraid_sas: Downgrade two success messages to info
cxlflash: Fix to resolve dead-lock during EEH recovery
scsi_debug: rework resp_report_luns
scsi_debug: use pdt constants
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons. For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to
get done.
Finally, reset controller handling as always gets merged through here
as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x+iD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
These updates fixes a number of issues where resources were not properly
released on probe errors. Included is also a fix for hardware
flow-control disable for cp210x.
Support for Moxa UPort 11x0 is added to the ti_usb_3410_5052 driver, and
included are also some general code clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8igx
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.7-rc1
These updates fixes a number of issues where resources were not properly
released on probe errors. Included is also a fix for hardware
flow-control disable for cp210x.
Support for Moxa UPort 11x0 is added to the ti_usb_3410_5052 driver, and
included are also some general code clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
The ohci-platform driver can control the clock, while usb-nop-xceiv
as the PHY can control the vbus regulator. So this JZ4740-specific
glue is not needed anymore.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13105/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for :
- UPort 1110 : 1 port RS-232 USB to Serial Hub.
- UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
- UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
- UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
- UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
These devices are based on TI 3410 chip.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[johan: fix rs485-only check ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Turns out the template and thus many drivers got the return value wrong:
0 means the fabrics driver needs to put a session reference, which no
driver except for the iSCSI target drivers did. Fortunately none of these
drivers supports explicit Node ACLs, so the bug was harmless.
Even without that only qla2xxx and iscsi every did real work in
shutdown_session, so get rid of the boilerplate code in all other
drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Due to a missing upper bound, invalid minor numbers could be assigned to
ports. Such devices would later fail to register, but let's catch this
early as intended and avoid having devices with only a subset of their
ports registered (potentially the empty set).
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interface read URB is submitted in attach, but was only unlinked by
the driver at disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we would end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callback.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org> # v3.5: 40d0473849
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interface read and event URBs are submitted in attach, but were
never explicitly unlinked by the driver. Instead the URBs would have
been killed by usb-serial core on disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we could end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callbacks.
Fixes: ee467a1f20 ("USB: serial: add Moxa UPORT 12XX/14XX/16XX
driver")
Cc: stable <stable@vger.kernel.org> # v3.14
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The URB status is signed and should be printed using %d rather than %x.
Also print endpoint addresses consistently using %x rather than %d, and
merge a broken-up error message string.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A driver must not rely on the URB status field to try to determine if an
URB is active.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interface instat and indat URBs were submitted in attach, but never
unlinked in release before deallocating the corresponding transfer
buffers.
In the case of a late probe error (e.g. due to failed minor allocation),
disconnect would not have been called before release, causing the
buffers to be freed while the URBs are still in use. We'd also end up
with active URBs for an unbound interface.
Fixes: f9c99bb8b3 ("USB: usb-serial: replace shutdown with disconnect,
release")
Cc: stable <stable@vger.kernel.org> # v2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
URBs and buffers allocated in attach for Epic devices would never be
deallocated in case of a later probe error (e.g. failure to allocate
minor numbers) as disconnect is then never called.
Fix by moving deallocation to release and making sure that the
URBs are first unlinked.
Fixes: f9c99bb8b3 ("USB: usb-serial: replace shutdown with disconnect,
release")
Cc: stable <stable@vger.kernel.org> # v2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Private data, URBs and buffers allocated for Epic devices during
attach were never released on errors (e.g. missing endpoints).
Fixes: 6e8cf7751f ("USB: add EPIC support to the io_edgeport driver")
Cc: stable <stable@vger.kernel.org> # v2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
This set of patches introduces a driver for the XUSB controller found on
NVIDIA Tegra SoCs. When loaded with a firmware (available via the linux-
firmware repository), it provides an XHCI-compatible interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BcOx
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-xhci' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "usb: host: xhci-tegra: Changes for v4.7-rc1" from Thierry Reding:
This set of patches introduces a driver for the XUSB controller found on
NVIDIA Tegra SoCs. When loaded with a firmware (available via the linux-
firmware repository), it provides an XHCI-compatible interface.
* tag 'tegra-for-4.7-xhci' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
Remove unnecessary space before open square bracket.
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The right part of the following or expression is only evaluated if
td is nonzero.
!td || (td && td.status == USB_TD_INPROGRESS)
So no need to check td again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware of R-Car USB 3.0 host controller will control the reset.
So, if the xhci driver doesn't do firmware downloading (e.g. kernel
configuration is CONFIG_USB_XHCI_PLATFORM=y and CONFIG_USB_XHCI_RCAR
is not set), the reset of USB 3.0 host controller doesn't work
correctly. Then, the host controller will cause long wait in
xhci_reset() because the CMD_RESET bit of op_regs->command is not
cleared for 10 seconds.
So, this patch modifies the Kconfig to enable both CONFIG_USB_XHCI_PLATFORM
and CONFIG_USB_XHCI_RCAR.
Fixes: 4ac8918f3a (usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers)
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The goto in create_sysfs_files is never executed, so remove it
and clean up the code.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not initialise statics to 0.
This patch is found by checkpatch.pl script.
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove space before ',' and '(' .
This patch is detected by checkpatch.pl
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some more new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=S5N0
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for v4.6-rc7
Here are some more new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
The CRTSCTS flag code cleared (and inconsistently) bits unrelated to
CRTSCTS functionality. It was also harder than necessary to read.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Replaced magic numbers used in the CRTSCTS flag code with symbolic names
from the chip specification.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
A bug in the CRTSCTS handling caused RTS to alternate between
CRTSCTS=0 => "RTS is transmit active signal" and
CRTSCTS=1 => "RTS is used for receive flow control"
instead of
CRTSCTS=0 => "RTS is statically active" and
CRTSCTS=1 => "RTS is used for receive flow control"
This only happened after first having enabled CRTSCTS.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Fixes: 39a66b8d22 ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org>
[johan: reword commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Some for documentation, some for tiny changes, thanks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXKY35AAoJEEhZKYFQ1nG7S+4H/0e4uLWow82UxNrYCDUMo/VI
Cto62Qo/lQTQb3iTsU3WD/SA1GOB0fei2GL53YuqoqsOcHSQQHMvnWQLps/YCHtT
l/YMY0arxysFNHkA+8wGTrfnRi/Nm2dJlSlkAJleTgD09dnobHYTk4AVDjSqvvb5
gvpMReTe4+ZsC7Nitum7Sg3dLHCJBdmXAWLKBOZ9beDSw5t1xbImjt8ud8k/eAYG
UseCqp8BClhKYGmLOAPRZvootmIvKEahGt0z2YXSJoVuHs0e3+7K23EVSV+zR+0Y
WMHdQXR4HOl6bcuXiHUKpN9SvUff7IxcMLnP/cBJ2lLHSVNS0yzO+NBsogx/f28=
=0707
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Hi Greg, below are changes for chipidea and OTG FSM, no major changes.
Some for documentation, some for tiny changes, thanks.
Add even more ZTE device ids.
Signed-off-by: lei liu <liu.lei78@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
[johan: rebase and replace commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
More ZTE device ids.
Signed-off-by: lei liu <liu.lei78@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
[properly sort them - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The stack object “ci” has a total size of 8 bytes. Its last 3 bytes
are padding bytes which are not initialized and leaked to userland
via “copy_to_user”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the original DWC3_DCFG_NUMP() was always zero. It looks like the
intent was to shift first and then do the mask.
Fixes: 2a58f9c12b ('usb: dwc3: gadget: disable automatic calculation of ACK TP NUMP')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implemenentation restart the sent pattern for each entry in
the sg list. The receiving end expects a continuous pattern, and test
will fail unless scatterilst entries happen to be aligned with the
pattern
Fix this by calculating the pattern byte based on total sent size
instead of just the current sg entry.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 8b52490193 ("[PATCH] USB: usbtest: scatterlist OUT data pattern testing")
Cc: <stable@vger.kernel.org> # v2.6.18+
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return type of usbhsp_setup_pipecfg() was u16 but it was returning
a negative value (-EINVAL). Lets have an additional argument which will
have pipecfg and just return the status (success or error) as the return
from the function.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB driver is bound to an interface (either through probing or
by claiming it) or is unbound from an interface, the USB core always
disables Link Power Management during the transition and then
re-enables it afterward. The reason is because the driver might want
to prevent hub-initiated link power transitions, in which case the HCD
would have to recalculate the various LPM parameters. This
recalculation takes place when LPM is re-enabled and the new
parameters are sent to the device and its parent hub.
However, if the driver does not want to prevent hub-initiated link
power transitions then none of this work is necessary. The parameters
don't need to be recalculated, and LPM doesn't need to be disabled and
re-enabled.
It turns out that disabling and enabling LPM can be time-consuming,
enough so that it interferes with user programs that want to claim and
release interfaces rapidly via usbfs. Since the usbfs kernel driver
doesn't set the disable_hub_initiated_lpm flag, we can speed things up
and get the user programs to work by leaving LPM alone whenever the
flag isn't set.
And while we're improving the way disable_hub_initiated_lpm gets used,
let's also fix its kerneldoc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthew Giassa <matthew@giassa.net>
CC: Mathias Nyman <mathias.nyman@intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for Gemalto's Cinterion PH8 and AHxx products
with 2 RmNet Interfaces and products with 1 RmNet + 1 USB Audio interface.
In addition some minor renaming and formatting.
Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
[johan: sort current entries and trim trailing whitespace ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit e3345db850, which
broke system resume for a large class of devices.
Devices that after having been reset during resume need to be rebound
due to a missing reset_resume callback, are now left in a suspended
state. This specifically broke resume of common USB-serial devices,
which are now unusable after system suspend (until disconnected and
reconnected) when USB persist is enabled.
During resume, usb_resume_interface will set the needs_binding flag for
such interfaces, but unlike system resume, run-time resume does not
honour it.
Cc: stable <stable@vger.kernel.org> # 4.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means all ->con_set_palette have to have the second parameter
const too now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_INITIALIZED bit in the tty_port::flags field with
TTY_PORT_INITIALIZED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_initialized() and tty_port_initialized() to abstract
atomic bit ops.
Note: the transforms for test_and_set_bit() and test_and_clear_bit()
are unnecessary as the state transitions are already mutually exclusive;
the tty lock prevents concurrent open/close/hangup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Abstract TTY_THROTTLED bit tests with tty_throttled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugging facilities in ehci-dbg.c follow an uneven pattern. Some
of them are protected by "#ifdef CONFIG_DYNAMIC_DEBUG" and some
aren't, presumably in the hope of having some of the debugging output
available in any configuration.
This leads to build problems when dynamic debugging isn't configured.
Rather than try to keep this complicated state of affairs, let's just
make everything dependent on CONFIG_DYNAMIC_DEBUG.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One line above we have checked that udc is NULL so we shouldn't
dereference it while printing error message.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We read a struct usb_device_descriptor from it, so make it an actual
binary attribute.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@gmail.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Tested-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB Type-C Connector System Software Interface (UCSI) is
specification that defines the registers and data structures
that can be used to control USB Type-C ports on a system.
UCSI is used on several Intel Broxton SoC based platforms.
Things that UCSI can be used to control include at least USB
Data Role swapping, Power Role swapping and controlling of
Alternate Modes on top of providing general details about
the port and the partners that are attached to it.
The initial purpose of the UCSI driver is to make sure USB
is in host mode on desktop and server systems that are USB
dual role capable, and provide UCSI interface.
The goal is to integrate the driver later to an USB Type-C
framework for Linux kernel, and at the same time add support
for more extensive USB Type-C port control that UCSI offers,
for example data role swapping, power role swapping,
Alternate Mode control etc.
The UCSI specification is public can be obtained from here:
http://www.intel.com/content/www/us/en/io/universal-serial-bus/usb-type-c-ucsi-spec.html
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Gyoi
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.6-rc6
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
Parameterize more parts of the driver and add support for Tegra210.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the on-chip XUSB controller present on Tegra SoCs. This
controller, when loaded with external firmware, exposes an interface
compliant with xHCI. This driver loads the firmware, starts the
controller, and is able to service host-specific messages sent by the
controller's firmware.
The controller also supports USB device mode as well as powergating
of the SuperSpeed and host-controller logic when not in use, but
support for these is not yet implemented.
Based on work by:
Ajay Gupta <ajayg@nvidia.com>
Bharath Yadav <byadav@nvidia.com>
Andrew Bresticker <abrestic@chromium.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the root hub device is added to the bus, it tries to get pins
information from pinctrl (see pinctrl_bind_pins, at really_probe), if
the pin information is described at DT, it will show below error since
the root hub's device node is the same with controller's, but controller's
pin has already been requested when it is added to platform bus.
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_GPIO_1 already
requested by 2184000.usb; cannot claim for usb1
imx6q-pinctrl 20e0000.iomuxc: pin-137 (usb1) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 137
(MX6Q_PAD_GPIO_1) from group usbotggrp-3 on device 20e0000.iomuxc
usb usb1: Error applying setting, reverse things back
To fix this issue, we move the root hub's device node assignment (equals
to contrller's) after device is added to bus, we only need to know root
hub's device node information after the device under root hub is created,
so this movement will not affect current function.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reported-by: Lars Steubesand <lars.steubesand@philips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary space before function pointer arguments.
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI controller presents two USB buses to the system - one for USB2
and one for USB3. The hub init code (hub_port_init) is reentrant but
only locks one bus per thread, leading to a race condition failure when
two threads attempt to simultaneously initialise a USB2 and USB3 device:
[ 8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 13.183701] usb 3-3: device descriptor read/all, error -110
On a test system this failure occurred on 6% of all boots.
The call traces at the point of failure are:
Call Trace:
[<ffffffff81b9bab7>] schedule+0x37/0x90
[<ffffffff817da7cd>] usb_kill_urb+0x8d/0xd0
[<ffffffff8111e5e0>] ? wake_up_atomic_t+0x30/0x30
[<ffffffff817dafbe>] usb_start_wait_urb+0xbe/0x150
[<ffffffff817db10c>] usb_control_msg+0xbc/0xf0
[<ffffffff817d07de>] hub_port_init+0x51e/0xb70
[<ffffffff817d4697>] hub_event+0x817/0x1570
[<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
[<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
[<ffffffff810f4684>] worker_thread+0x64/0x4b0
[<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
[<ffffffff810fa7f5>] kthread+0x105/0x120
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
[<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
Call Trace:
[<ffffffff817fd36d>] xhci_setup_device+0x53d/0xa40
[<ffffffff817fd87e>] xhci_address_device+0xe/0x10
[<ffffffff817d047f>] hub_port_init+0x1bf/0xb70
[<ffffffff811247ed>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff817d4697>] hub_event+0x817/0x1570
[<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
[<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
[<ffffffff810f4684>] worker_thread+0x64/0x4b0
[<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
[<ffffffff810fa7f5>] kthread+0x105/0x120
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
[<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
Which results from the two call chains:
hub_port_init
usb_get_device_descriptor
usb_get_descriptor
usb_control_msg
usb_internal_control_msg
usb_start_wait_urb
usb_submit_urb / wait_for_completion_timeout / usb_kill_urb
hub_port_init
hub_set_address
xhci_address_device
xhci_setup_device
Mathias Nyman explains the current behaviour violates the XHCI spec:
hub_port_reset() will end up moving the corresponding xhci device slot
to default state.
As hub_port_reset() is called several times in hub_port_init() it
sounds reasonable that we could end up with two threads having their
xhci device slots in default state at the same time, which according to
xhci 4.5.3 specs still is a big no no:
"Note: Software shall not transition more than one Device Slot to the
Default State at a time"
So both threads fail at their next task after this.
One fails to read the descriptor, and the other fails addressing the
device.
Fix this in hub_port_init by locking the USB controller (instead of an
individual bus) to prevent simultaneous initialisation of both buses.
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.org/lkml/2016/2/8/312
Link: https://lkml.org/lkml/2016/2/4/748
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Init data marked const should be annotated with __initconst for
correctness and not __initdata. This also fixes LTO builds that
otherwise fail with section mismatch errors.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbdev_vm_ops is used in devio.c only, so declare it as static
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
urb allocation will fail when usbtest_alloc_urb() tries to
allocate zero length buffer, but it doesn't need it in fact,
so just skips buffer allocation in the case.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NULL pointer dereferrence will happen when class driver
wants to allocate zero length buffer and pool_max[0]
can't be used, so simply returns NULL in the case.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the addition of VUDC, the USBIP stack can now be used on
configurations without USB host support, but trying to build
it with USB gadget support disabled fails with
drivers/usb/built-in.o: In function `vep_dequeue':
vudc_main.c:(.text+0xa6ddc): undefined reference to `usb_gadget_giveback_request'
drivers/usb/built-in.o: In function `nuke':
vudc_main.c:(.text+0xa6ea8): undefined reference to `usb_gadget_giveback_request'
drivers/usb/built-in.o: In function `vudc_device_reset':
vudc_main.c:(.text+0xa720c): undefined reference to `usb_gadget_udc_reset'
drivers/usb/built-in.o: In function `vudc_probe':
This addresses both issues, by changing the dependency for USBIP_CORE
to USB_COMMON, and adding additional dependencies on USB or USB_GADGET
for the individual portions as needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9360575c58 ("usbip: vudc: Add vudc to Kconfig")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a code fragment to ignore completing URBs in closing
connection.
Regarding this patch, 2 execution contexts are related.
1) stub_tx.c: stub_complete() which is called from USB core
1-1) add to unlink list and free URB or
1-2) move to tx list
2) stub_dev.c: stub_shutdown_connection() which is invoked by unbind
operation through sysfs.
2-1) stop TX/RX threads
2-2) close TCP connection and set ud.tcp_socket to NULL
2-3) cleanup pending URBs by stub_device_cleanup_urbs(sdev)
2-4) free unlink list (no lock)
In the race condition, URBs which will be cleared in 2-3) may be
handled in 1).
In case 1-1), it will not be transferred bcause tx threads are stooped
in 2-1).
In case 1-2), may be freed in 2-4).
With this patch, after 2-2), completing URBs in 1) will not be handled
and cleared in 2-3).
The kernel log with this patch is as below.
kernel: usbip_core: usbip_kernel_unlink:792: shutting down tcp_socket
ef61d980
kernel: usbip-host 1-3: free sdev f5df6180
kernel: usbip-host 1-3: free urb f5df6700
kernel: usbip-host 1-3: Enter
kernel: usbip_core: usbip_stop_eh:132: usbip_eh waiting completion 5
kernel: usbip_host: stub_complete:71: complete! status 0
kernel: usbip_host: stub_complete:102: ignore urb for closed connection
e725fc00 (*)
kernel: usbip_host: stub_complete:71: complete! status -2
kernel: usbip-host 1-3: stopped by a call to usb_kill_urb() because of
cleaning up a virtual connection
kernel: usbip-host 1-3: free urb e725fc00 (**)
kernel: usbip-host 1-3: free urb e725e000
kernel: usbip_host: stub_complete:71: complete! status -2
kernel: usbip-host 1-3: stopped by a call to usb_kill_urb() because of
cleaning up a virtual connection
kernel: usbip-host 1-3: free urb e725f800
kernel: usbip_host: stub_complete:71: complete! status -2
kernel: usbip-host 1-3: stopped by a call to usb_kill_urb() because of
cleaning up a virtual connection
kernel: usbip-host 1-3: free urb e725e800
kernel: usbip_host: stub_complete:71: complete! status -2
kernel: usbip-host 1-3: stopped by a call to usb_kill_urb() because of
cleaning up a virtual connection
kernel: usbip-host 1-3: device reset
kernel: usbip-host 1-3: lock for reset
kernel: usbip_host: store_match_busid:178: del busid 1-3
kernel: uvcvideo: Found UVC 1.00 device Venus USB2.0 Camera (056e:700a)
kernel: input: Venus USB2.0 Camera as
/devices/pci0000:00/0000:00:1a.7/usb1/1-3/1-3:1.0/input/input22
(*) skipped with this patch in completion
(**) released in 2-3
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As find_endpoint() is a global funcion rename it to vudc_find_endpoint()
to clearly mark where does it come from.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix NULL pointer dereference and obsolete comments forgotten when
usbip server was converted from an interface driver to a device driver.
Signed-off-by: Alexander Popov <alpopov@ptsecurity.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix WARN_ON() macro usage as suggested by Felipe.
Instead of using:
if (cond) {
WARN_ON(1);
do_stuff();
}
Use a better pattern with WARN_ON() placed in if condition:
if (WARN_ON(cond))
do_stuff();
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7szP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.7 merge window
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
Now that we calculate DCFG.NUMP, we can disable
dwc3's automatic calculation so we maximize our
chances of very high throughtput through the use of
bursts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NumP field of DCFG register is used on NumP field of
ACK TP header and it tells the host how many packets
an endpoint can receive before waiting for
synchronization.
Documentation says it should be set to anything
<=bMaxBurst. Interestingly, however, this setting is
not per-endpoint how it should be (different
endpoints could have different burst sizes), but
things seem to work okay right now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleanup in probe if we fail to get dr_mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of DDMA mode we don't need to get an SOF interrupt so disable
the unmasking of SOF interrupt in DDMA mode.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is safety change added while doing slub debugging.
Affected functions:
dwc2_hcd_qtd_unlink_and_free()
_dwc2_hcd_urb_enqueue()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In host slave mode, the core asserts the rxready, txfifoempty interrupts
that get serviced in the gadget irq handler. Prevent servicing of these
when not in the gadget mode of operation.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Replaced the WARN_ON with a check and return of -EINVAL in the
dwc2_hsotg_ep_enable function if ep0 is passed in.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
if Start Transfer command fails, let's try a little
harder to figure out why the command failed and give
slightly better return codes. This will be usefulf
or isochronous endpoints, at least, which could
decide to retry a given request.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If a gadget driver loaded to a Superspeed-capable
peripheral controller, using a Superspeed cable,
doesn't provide Superspeed descriptors, we will get
a NULL pointer dereference.
In order to avoid that situation, we will try to
find any valid descriptors we can. If no set of
descriptors is passed in, then we'll let that gadget
oops anyhow.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For convenience, passing the dwc3 platform device as a
parameter to dwc3_pci_quirks() function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Setting the ACPI companion before calling dwc3_pci_quirks.
The ACPI companion will be set unconditionally as the
primary fwnode, overriding any previously set primary
fwnode. This will make sure that any build-in properties
added to the platform device will be added as the secondary
fwnode in cases where also ACPI companion exists.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case host sends us an unsupported test mode, we
*must* stall this request. This will tell the host
that the selector is invalid and we won't put the
controller in unsupported test modes which could
have undetermined side-effects.
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
whc_init already calls whc_clean_up if an error occurs during
the initialization, so calling it again if whc_init fails at
the end of wch_probe will cause double free errors. Fix this
by bailing out on an whc_init failure to a new label that avoids
doing the duplicated whc_clean_up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thanks to switching to devm_gpiod_get:
1) We don't have to pass fwnode pointer
2) We can request initial GPIO value at getting call
This was successfully tested on Netgear R6250 (BCM4708).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that there are no more users for
xhci_plat_type_is(), we can safely remove it.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the code has been refactored enough,
switching over to using ->plat_start() and
->init_quirk() becomes a very simple patch.
After this patch, there are no further uses for
xhci_plat_type_is() which will be removed in a
follow-up patch.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like RCAR's init_quirk() we want mvebu's to use
struct usb_hcd * as argument too. This is another
step towards removing xhci_plat_type_is().
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_plat_setup() is the rightful place for
xhci_mvebu_mbus_init_quirk(), so let's move it there
in order to make it simpler to get rid of
xhci_plat_type_is() later on.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
these two methods will be used to hide
platform-specific details so we can get rid of
xhci_plat_type_is() in a later patch.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're preparing to remove xhci_plat_type_is() in
favor of a better approach where we define function
pointers ahead of time. This will let us make
assumptions about which platforms we're running on
and which platform-specific functions we should call.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[delete extra comma in function parameters -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move duplicate code from xhci_queue_intr_tx()
and xhci_queue_isoc_tx_prepare() to the check_interval() function.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove duplicate function xhci_urb_to_transfer_ring from xhci.c.
We have same function in xhci-ring.c.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In drivers/usb/host/xhci-ring.c there are two functions
(xhci_queue_bulk_tx and queue_bulk_sg_tx) that are very similar,
so a lot of code duplication.
This patch merges these functions into to one xhci_queue_bulk_tx.
Also counting the needed TRBs is merged and refactored.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restructure usb_sg_cancel() so we don't have to disable interrupts
while cancelling the URBs.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_submit_urb() may take quite long to execute. For example, a
single sg list may have 30 or more entries, possibly leading to that
many calls to DMA-map pages. This can cause interrupt latency of
several hundred micro-seconds.
Avoid the problem by releasing the io->lock spinlock and re-enabling
interrupts before calling usb_submit_urb(). This opens races with
usb_sg_cancel() and sg_complete(). Handle those races by using
usb_block_urb() to stop URBs from being submitted after
usb_sg_cancel() or sg_complete() with error.
Note that usb_unlink_urb() is guaranteed to return -ENODEV if
!io->urbs[i]->dev and since the -ENODEV case is already handled,
we don't have to check for !io->urbs[i]->dev explicitly.
Before this change, reading 512MB from an ext3 filesystem on a USB
memory stick showed a throughput of 12 MB/s with about 500 missed
deadlines.
With this change, reading the same file gave the same throughput but
only one or two missed deadlines.
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the driver to Kconfig to make it visible in menuconfig
and allow people to compile it.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sysfs attributes to allow controlling vudc from usbip tools.
dev_desc - device descriptor of current gadget. This is required to
be consisten with current usbip protocol and allow to list
exportable devices on given machine.
usbip_sockfd - allows to pass socket to kernel to start usbip transfer.
usbip_status - currnent status of device
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Various bug fixes, improvements and commit msg update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add endpoints definitions and ops for both endpoints and gadget.
Add also a suitable platform driver and functions for handling
usbip events.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Various bug fixes, improvements and commit msg update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file contains functions for returning requests to the client.
It also has functions that add requests completed in vudc_rx and
vudc_transfer to the return queue.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file contains a function that simulates USB traffic, based on
the one in dummy_hcd. Is also handles udc-directed control
requests, and contains functions for setting up and controlling
a timer for the emulation.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add functions which allows to receive urbs from the client.
It receives traffic in a loop in a separate thread.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add main vudc module file. This allows us to register suitable
platform device and driver (just like dummy_hcd does).
Currently number of vudc instances is determined using module
parameter but whole infrastructure is suitable to make vudc
creation dynamic (for example via configfs).
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Various bug fixes and commit message update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add constants for VUDC events in usbip_common.h
and make use of them in usbip_common.c.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Small fixes and commit message update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add header with definitions needed by vudc driver.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Some small improvements]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional changes here, just making sure our
storage driver uses a consistent multi-line comment
style.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 devices, because they are much newer, have much
less chance of having issues with larger transfers.
We still keep a limit because anything above 2048
sectors really rendered negligible speed
improvements, so we will simply ignore
that. Transferring 1MiB should already give us
pretty good performance.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just so we have some sort of documentation as to why
we limit our Mass Storage transfers to 240 sectors,
let's update the comment to make clearer that
devices were found that would choke with larger
transfers.
While at that, also make sure to clarify that other
operating systems have similar, albeit different,
limits on mass storage transfers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a port can do 10 Gb/s the kernel should say so.
The corresponding check needs to be added.
Signed-off.by: Oliver Neukum <ONeukum@suse.com>>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_get_phy() function returns either a valid pointer to phy or
ERR_PTR() error, check for NULL always fails and may lead to oops on
error path, fix this issue.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2035772010.
Commit 20357720 claims throughput improvement for MSC/UVC, but I
don't see much improvement. Following are the MSC measurement using
dd on AM335x GP EVM.
with BCD_BH: read: 14.9MB/s, write: 20.9MB/s
without BCD_BH: read: 15.2MB/s, write: 21.2MB/s
However with this commit the following regressions have been observed.
1. ASIX usb-ethernet dongle is completely broken on UDP RX.
2. Unpluging a 3G modem, which uses option driver, behind a hub causes
console log flooding with the following message.
option_instat_callback: error -71
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions, such as f_sourcesink, rely on an endpoint's desc
field during their requests' complete() callback, so clear it only
_after_ nuking all requests to avoid NULL pointer dereference.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The ftdi_sio_quirk structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Johan Hovold <johan@kernel.org>
Adding VID:PID for Straizona Focusers to cp210x driver.
Signed-off-by: Jasem Mutlaq <mutlaqja@ikarustech.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Link ECU is an aftermarket ECU computer for vehicles that provides
full tuning abilities as well as datalogging and displaying capabilities
via the USB to Serial adapter built into the device.
Signed-off-by: Mike Manning <michael@bsch.com.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When using asynchronous read or write operations on the USB endpoints the
issuer of the IO request is notified by calling the ki_complete() callback
of the submitted kiocb when the URB has been completed.
Calling this ki_complete() callback will free kiocb. Make sure that the
structure is no longer accessed beyond that point, otherwise undefined
behaviour might occur.
Fixes: 2e4c7553cd ("usb: gadget: f_fs: add aio support")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a bunch of information in the debug register
set from dwc3 which is useful in some debugging
scenarios. Let's dump them out in endpoint-specific
directories and designated files.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This helper will be used later to convert trb type
into a human-readable string for debugfs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this helper will be used, initially, to dump space
of different queues and fifos in dwc3 to
debugfs. Later, it'll be used to issue remote wakeup
when we want to start a transfer and there's
something in a TX FIFO.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Coccinelle caught this instance of us kfree()ing
devm-allocated memory. The solution is just to not
do anything in our gadget_release.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When binding the function to usb_configuration, check whether the thread
is running before starting another one. Without that, when function
instance is added to multiple configurations, fsg_bing starts multiple
threads with all but the latest one being forgotten by the driver. This
leads to obvious thread leaks, possible lockups when trying to halt the
machine and possible more issues.
This fixes issues with legacy/multi¹ gadget as well as configfs gadgets
when mass_storage function is added to multiple configurations.
This change also simplifies API since the legacy gadgets no longer need
to worry about starting the thread by themselves (which was where bug
in legacy/multi was in the first place).
N.B., this patch doesn’t address adding single mass_storage function
instance to a single configuration twice. Thankfully, there’s no
legitimate reason for such setup plus, if I’m not mistaken, configfs
gadget doesn’t even allow it to be expressed.
¹ I have no example failure though. Conclusion that legacy/multi has
a bug is based purely on me reading the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the current implementation functionfs generates a EFAULT for async read
operations if the read buffer size is larger than the URB data size. Since
a application does not necessarily know how much data the host side is
going to send it typically supplies a buffer larger than the actual data,
which will then result in a EFAULT error.
This behaviour was introduced while refactoring the code to use iov_iter
interface in commit c993c39b86 ("gadget/function/f_fs.c: use put iov_iter
into io_data"). The original code took the minimum over the URB size and
the user buffer size and then attempted to copy that many bytes using
copy_to_user(). If copy_to_user() could not copy all data a EFAULT error
was generated. Restore the original behaviour by only generating a EFAULT
error when the number of bytes copied is not the size of the URB and the
target buffer has not been fully filled.
Commit 342f39a6c8 ("usb: gadget: f_fs: fix check in read operation")
already fixed the same problem for the synchronous read path.
Fixes: c993c39b86 ("gadget/function/f_fs.c: use put iov_iter into io_data")
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This function compiles to 298 bytes of machine code, has ~10 callsites.
This is a USB 2.0 device, USB 2.0 is limited to ~40 MB/s, so should be
almost never CPU bound. No need to optimize for speed this agressively.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Felipe Balbi <balbi@ti.com>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The previous code could use the first USB-DMAC with IPMMU if iommus
property was set into this device node. However, in this case, it
could not control the second USB-DMAC with IPMMU because a parameter
of IPMMU (micro-TLB id) is different with each USB-DMAC.
So, this patch uses the usb_gadget_{un}map_request_by_dev() APIs for
IPMMU. (Then, iommus property should be set into USB-DMAC node(s).)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since usbhsg_dma_map_ctrl() needs DMA device structure in the near future,
this patch changes arguments of dma_map_ctrl() to give such data.
(This patch is only change the argument.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since usbhsf_dma_{un}map() will use the "fifo" data in the near future,
this patch changes function call orfer in usbhsf_dma_prepare_push().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the following environment, the first argument of DMA API should
be set to a DMAC's device structure, not a udc controller's one.
- A udc controller needs an external DMAC device (like a DMA Engine).
- The external DMAC enables IOMMU.
So, this patch add usb_gadget_{un}map_request_by_dev() API to set
a DMAC's device structure by a udc controller driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The argument of dev_err() in usb_gadget_map_request() should be dev
instead of &gadget->dev.
Fixes: 7ace8fc ("usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU")
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Debugfs init failure is not so important. We can continue our job on
this failure. Also no break need for debugfs_create_file call failure.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[felipe.balbi@linux.intel.com :
- remove out-of-memory message, we get that from OOM.
- switch dev_err() to dev_dbg() ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dma_status bit flag is set but never really used
so get rid of it.
Reported-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It makes no sense to interrupt in the middle of
chained transfer. This patch just makes sure we
don't do that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of limiting link TRB only to Isoc endpoints,
let's use it for all endpoint types, this way we are
more likely to transfer more data before a
XferComplete event.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By moving our % DWC3_NUM_TRB operation to the
increment helpers, the rest of the driver can be
simplified.
It's also a good practice to make sure we will have
a single place dealing with details about how to
increment our enqueue and dequeue pointers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add three little helpers which will aid in making
the code slightly easier to read. One helper
increments enqueue pointer, another increments
dequeue pointer and the last one tests if we're
dealing with the last TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a bitwise and, let's rely on the %
operator since that's a lot more clear. Also, GCC
will optimize % 256 to nothing anyway.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The call to wusb_dev_sysfs_rm() which is just after return will never
be executed. On checking the code, wusb_dev_sysfs_add() is the last one
to be executed so even if that fails we do not need wusb_dev_sysfs_rm()
in the error path.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dear all,
1. Overview
In current USB/IP implementation, event kernel threads are created for
each port. The functions of the threads are closing connection and
error handling so they don't have not so many events to handle. There's
no need to have thread for each port.
BEFORE) vhci side - VHCI_NPORTS(8) threads are created.
$ ps aux | grep usbip
root 10059 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10060 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10061 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10062 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10063 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10064 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10065 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10066 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
BEFORE) stub side - threads will be created every bind operation.
$ ps aux | grep usbip
root 8368 0.0 0.0 0 0 ? S 17:56 0:00 [usbip_eh]
root 8399 0.0 0.0 0 0 ? S 17:56 0:00 [usbip_eh]
This patch put event threads of stub and vhci driver as one workqueue.
AFTER) only one event threads in each vhci and stub side.
$ ps aux | grep usbip
root 10457 0.0 0.0 0 0 ? S< 17:47 0:00 [usbip_event]
2. Modification to usbip_event.c
BEFORE) kernel threads are created in usbip_start_eh().
AFTER) one workqueue is created in new usbip_init_eh().
Event handler which was main loop of kernel thread is modified to
workqueue handler.
Events themselves are stored in struct usbip_device - same as before.
usbip_devices which have event are listed in event_list.
The handler picks an element from the list and wakeup usbip_device. The
wakeup method is same as before.
usbip_in_eh() substitutes statement which checks whether functions are
called from eh_ops or not. In this function, the worker context is used
for the checking. The context will be set in a variable in the
beginning of first event handling. usbip_in_eh() is used in event
handler so it works well.
3. Modifications to programs using usbip_event.c
Initialization and termination of workqueue are added to init and exit
routine of usbip_core respectively.
A. version info
v2)
# Merged 1/2 event handler itself and 2/2 user programs because of auto
build fail at 1/2 casued unmodified user programs in 1/2.
Signed-off-by: Nobuo Iwata <nobuo.iwata@fujixerox.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing checks for dma mapping error in qset_fill_page_list(),
I have missed two similar problems in qset_add_urb_sg() and
in qset_add_urb_sg_linearize().
v2: check validity of dma_addr with dma_mapping_error()
in qset_free_std() as suggested by Vladimir Zapolskiy.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 0.95 xHCI spec says that non-control endpoints will be halted if a
babble is detected on a transfer. The 0.96 xHCI spec says all types of
endpoints will be halted when a babble is detected. Some hardware that
claims to be 0.95 compliant halts the control endpoint anyway.
Reference: http://www.spinics.net/lists/linux-usb/msg21755.html
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We *know* that we have 1 PAGE (4096 bytes) for our
TRB poll. We also know the size of each TRB and know
that we can fit 256 of them in one PAGE. By using a
u8 type we can make sure that:
enqueue++ % 256;
gets optimized to an increment only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it clear that we're dealing with a queue
of TRBs. No functional changes. While at that, also
rename start_slot to first_trb_index for similar
reasons.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DWC3 OMAP driver supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-omap.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook says we should move link to U0
before issuing a Start Transfer command. We could
require the gadget driver to call
usb_gadget_wakeup() however I feel that changing all
gadget drivers to keep track of Link State and
conditionally call usb_gadget_wakeup() would be far
too much work. For now we will handle this at the
UDC level, but at some point composite.c should be
one handling this.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.
This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.
Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sort IDs in groups to be easily found when needed.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It seems there are leftovers of some assignments which are not used
anymore. Compiler even warns us about:
drivers/usb/gadget/udc/pch_udc.c:2022:22: warning: variable ‘dev’ set \
but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/pch_udc.c:2639:9: warning: variable ‘ret’ set \
but not used [-Wunused-but-set-variable]
Remove them and shut compiler about.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Try to enable MSI in case hardware supports it. At least Intel Quark is
known SoC which indeed does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devres API allows to make error paths cleaner and less error
prone. Convert the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no need to repeat the work that is already done in the PCI
driver core. The patch removes excerpts from suspend and resume
callbacks.
Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].
While here, convert PM ops to use modern API.
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[felipe.balbi@linux.intel.com: fixed build break and checkpatch error ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The phy-am335x driver selects 'USB_COMMON', but all other drivers
use 'depends on' for that symbol, and it depends on USB || USB_GADGET
itself, which causes a Kconfig warning:
warning: (AM335X_PHY_USB) selects USB_COMMON which has unmet direct dependencies (USB_SUPPORT && (USB || USB_GADGET))
As suggested by Felipe Balbi, this turns the logic around, and makes
'USB_COMMON' selected by everything else that needs it, so we can
remove the dependencies.
Fixes: 59f042f644 ("usb: phy: phy-am335x: bypass first VBUS sensing for host-only mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we don't plan on using multiple event buffers, but
if we find a good use case for it, this little trick
will help us avoid a loop in hardirq handler looping
for each and every event buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget controller might not be always active during system
suspend/resume as gadget driver might not have yet been loaded or
might have been unloaded prior to system suspend.
Check if we're active and only then perform
necessary actions during suspend/resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc->regset is allocated on dwc3_debugfs_init, and should
be released on init failure or dwc3_debugfs_exit. Btw,
The line "dwc->root = NULL" is unnecessary, so remove it.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[ felipe.balbi@linux.intel.com : add another err label for the new
error condition ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we need to power off the PHY during suspend and
power it back on during resume.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: fix call to usb_phy_set_suspend() in dwc3_suspend()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even if pm_runtime_get*() fails, we *MUST* call
pm_runtime_put_sync() before disabling PM.
While at it, remove superfluous dwc3_omap_disable_irqs()
in error path.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: patch description updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set the reserved fields of the SuperSpeed Plus Device Capability
descriptor to 0. Otherwise there might be stale data there which will
cause USB CV to fail.
Fixes: f228a8de24 ("usb: gadget: composite: Return SSP Dev Cap descriptor")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
we will be using a single event buffer and that
renders ev_buffs array unnecessary. Let's remove it
in favor of a single pointer to a single event
buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We never, ever route any of the other event buffers
so we might as well drop support for them.
Until someone has a real, proper benefit for
multiple event buffers, we will rely on a single
one. This also helps reduce memory footprint of
dwc3.ko which won't allocate memory for the extra
event buffers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
coccicheck found this pattern which could be
converted to PTR_ERR_OR_ZERO(). No functional
changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
coccicheck found this pattern which could be
converted to PTR_ERR_OR_ZERO(). No functional
changes.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
request_list and req_queued were, well, weird naming
choices.
Let's give those better names and call them,
respectively, pending_list and started_list. These
new names better reflect what these lists are
supposed to do.
While at that also rename req->queued to req->started.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
previously we were using a maximum of 32 TRBs per
endpoint. With each TRB being 16 bytes long, we were
using 512 bytes of memory for each endpoint.
However, SLAB/SLUB will always allocate PAGE_SIZE
chunks. In order to better utilize the memory we
allocate and to allow deeper queues for gadgets
which would benefit from it (g_ether comes to mind),
let's increase the maximum to 256 TRBs which rounds
up to 4096 bytes for each endpoint.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit of TRB Control is useful for protocols such
CDC EEM/ECM/NCM where we're transferring in blocks
of MTU-sized requests (usually MTU is 1500 bytes).
We know we will always have a short packet after two
(for HS) wMaxPacketSize packets and, usually, we
will have a long(-ish) queue of requests (for our
g_ether gadget, we have at least 10
requests).
Instead of always stopping the queue processing to
interrupt, giveback and restart, let's tell dwc3 to
interrupt but continue processing following request
if we have anything already pending in the queue.
This gave me a considerable improvement of 40% on my
test setup.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16f8 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On BXT platform Host Controller and Device Controller figure as
same PCI device but with different device function. HCD should
not pass data to Device Controller but only to Host Controllers.
Checking if companion device is Host Controller, otherwise skip.
Cc: <stable@vger.kernel.org>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new NO_REPORT_LUNS quirk and set it for Seagate drives with
an usb-id of: 0bc2:331a, as these will fail to respond to a
REPORT_LUNS command.
Cc: stable@vger.kernel.org
Reported-and-tested-by: David Webb <djw@noc.ac.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 64d513ac31 ("scsi: use host wide tags by default") causes
the SCSI core to queue more commands then we can handle on devices with
multiple LUNs, limit the queue depth at the scsi-host level instead of
per slave to fix this.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1315013
Cc: stable@vger.kernel.org # 4.4.x and 4.5.x
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise generic-xhci and xhci-platform which have no data get wrongly
detected as XHCI_PLAT_TYPE_MARVELL_ARMADA by xhci_plat_type_is().
This fixes a regression in v4.5 for STiH407 family SoC's which use the
synopsis dwc3 IP, whereby the disable_clk error path gets taken due to
wrongly being detected as XHCI_PLAT_TYPE_MARVELL_ARMADA and the hcd never
gets added.
I suspect this will also fix other dwc3 DT platforms such as Exynos,
although I've only tested on STih410 SoC.
Fixes: 4efb2f6941 ("usb: host: xhci-plat: add struct xhci_plat_priv")
Cc: stable@vger.kernel.org
Cc: gregory.clement@free-electrons.com
Cc: yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes some wild pointers produced by xhci_mem_cleanup.
These wild pointers will cause system crash if xhci_mem_cleanup()
is called twice.
Reported-and-tested-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that cannot work if R-Car Gen2/3 run on
above 4GB physical memory environment to use a quirk XHCI_NO_64BIT_SUPPORT.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0) of
HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit
address memory pointers actually. So, in this case, this driver should
call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in xhci_gen_setup().
Otherwise, the xHCI controller will be died after a usb device is
connected if it runs on above 4GB physical memory environment.
So, this patch adds a new quirk XHCI_NO_64BIT_SUPPORT to resolve
such an issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.
Cc: <stable@vger.kernel.org>
Tested-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Broxton B0 also requires XHCI_PME_STUCK_QUIRK.
Adding PCI device ID for Broxton B and adding to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under some circumstances acm_tty_flush_chars() is called
with no buffer to flush. We simply need to do nothing.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as they
are "trivial".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlcJLLUACgkQMUfUDdst+ym3wgCeNSzb74ZskDbGsXUooE0XhYRc
iPoAnRpn/ahoBTzmkKiQXQ1+Br8pAUtN
=vyU/
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as
they are 'trivial'"
* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: option: add "D-Link DWM-221 B1" device id
USB: serial: cp210x: Adding GE Healthcare Device ID
USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
usb: dwc3: keystone: drop dma_mask configuration
usb: gadget: udc-core: remove manual dma configuration
usb: dwc3: pci: add ID for one more Intel Broxton platform
usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
usb: dwc2: do not override forced dr_mode in gadget setup
usb: gadget: f_midi: unlock on error
USB: digi_acceleport: do sanity checking for the number of ports
USB: cypress_m8: add endpoint sanity check
USB: mct_u232: add sanity checking in probe
usb: fix regression in SuperSpeed endpoint descriptor parsing
USB: usbip: fix potential out-of-bounds write
usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
usb: phy: qcom-8x16: fix regulator API abuse
usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
usb: gadget: composite: Access SSP Dev Cap fields properly
...
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vUqa
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.6-rc3
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
We have two more fixes to f_midi. It should now
behave much better.
dwc3-keystone.c has gotten a fix which now allows it
to work on keystone device when running in
peripheral mode. A similar fix for DMA configuration
was made for udc-core, too.
We have a new PCI ID for Intel's Broxton
platform. DWC3 can run on those platforms as well.
And we also have some dwc2 got a fix for dr_mode
usage, while renesas controller got 3 important
fixes: a NULL pointer deref fix, IRQ <-> DMA race
fix, and a fix to prevent a situation where we would
queue a request to a disabled endpoint.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QLLF
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.6-rc3
We have two more fixes to f_midi. It should now
behave much better.
dwc3-keystone.c has gotten a fix which now allows it
to work on keystone device when running in
peripheral mode. A similar fix for DMA configuration
was made for udc-core, too.
We have a new PCI ID for Intel's Broxton
platform. DWC3 can run on those platforms as well.
And we also have some dwc2 got a fix for dr_mode
usage, while renesas controller got 3 important
fixes: a NULL pointer deref fix, IRQ <-> DMA race
fix, and a fix to prevent a situation where we would
queue a request to a disabled endpoint.
The CP2105 is used in the GE Healthcare Remote Alarm Box, with the
Manufacturer ID of 0x1901 and Product ID of 0x0194.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A Fedora user reports that the ftdi_sio driver works properly for the
ICP DAS I-7561U device. Further, the user manual for these devices
instructs users to load the driver and add the ids using the sysfs
interface.
Add support for these in the driver directly so that the devices work
out of the box instead of needing manual configuration.
Reported-by: <thesource@mail.ru>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Keystone 2 supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-keystone.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Cc: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since commit 7ace8fc821 ("usb: gadget: udc: core: Fix argument of
dma_map_single for IOMMU") it is not necessary to configure DMA for
usb_gadget device manually, because all DMA operation are performed
using parent/controller device.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
BXT-M is a Intel Broxton SoC based platform with unique PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move the state_changed variable into struct otg_fsm
so that we can support multiple instances.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
For each platform devices which is created by device tree, the default
DMA mask is set by of_dma_configure when the device are created. So
delete the redundant code at driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes an issue that usbhsg_queue_done() may cause kernel
panic when dma callback is running and usb_ep_disable() is called
by interrupt handler. (Especially, we can reproduce this issue using
g_audio with usb-dmac driver.)
For example of a flow:
usbhsf_dma_complete (on tasklet)
--> usbhsf_pkt_handler (on tasklet)
--> usbhsg_queue_done (on tasklet)
*** interrupt happened and usb_ep_disable() is called ***
--> usbhsg_queue_pop (on tasklet)
Then, oops happened.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The host/device mode set with dr_mode should be kept all the time,
not being changed to OTG in gadget setup (by overriding CFGUSB_FORCEDEVMODE
and CFGUSB_FORCEHOSTMODE bits).
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Przemek Rudy <prudy1@o2.pl>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We added some new locking here, but missed an error path where we need
to unlock.
Fixes: 9acdf4df2f ('usb: gadget: f_midi: added spinlock on transmit function')
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver can be crashed with devices that expose crafted descriptors
with too few endpoints.
See: http://seclists.org/bugtraq/2016/Mar/61
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
[johan: fix OOB endpoint check and add error messages ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An attack using the lack of sanity checking in probe is known. This
patch checks for the existence of a second port.
CVE-2016-3136
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
CC: stable@vger.kernel.org
[johan: add error message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b37d83a6a4 ("usb: Parse the new USB 3.1 SuperSpeedPlus Isoc
endpoint companion descriptor") caused a regression in 4.6-rc1 and fails
to parse SuperSpeed endpoint companion descriptors.
The new SuperSpeedPlus Isoc endpoint companion parsing code incorrectly
decreased the the remaining buffer size before comparing the size with the
expected length of the descriptor.
This lead to possible failure in reading the SuperSpeed endpoint companion
descriptor of the last endpoint, displaying a message like:
"No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0
ep 129: using minimum values"
Fix it by decreasing the size after comparing it.
Also finish all the SS endpoint companion parsing before calling SSP isoc
endpoint parsing function.
Fixes: b37d83a6a4
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential out-of-bounds write to urb->transfer_buffer
usbip handles network communication directly in the kernel. When receiving a
packet from its peer, usbip code parses headers according to protocol. As
part of this parsing urb->actual_length is filled. Since the input for
urb->actual_length comes from the network, it should be treated as untrusted.
Any entity controlling the network may put any value in the input and the
preallocated urb->transfer_buffer may not be large enough to hold the data.
Thus, the malicious entity is able to write arbitrary data to kernel memory.
Signed-off-by: Ignat Korchagin <ignat.korchagin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a code to surely disable TX IRQ of the pipe before
starting TX DMAC transfer. Otherwise, a lot of unnecessary TX IRQs
may happen in rare cases when DMAC is used.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
buflen by default (256) is smaller than wMaxPacketSize (512) in high-speed
devices.
That caused the OUT endpoint to freeze if the host send any data packet of
length greater than 256 bytes.
This is an example dump of what happended on that enpoint:
HOST: [DATA][Length=260][...]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
...
HOST: [PING]
DEVICE: [NAK]
This patch fixes this problem by setting the minimum usb_request's buffer size
for the OUT endpoint as its wMaxPacketSize.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
gcc warns about the use of regulators in phy_8x16_probe:
drivers/usb/phy/phy-qcom-8x16-usb.c: In function 'phy_8x16_probe':
drivers/usb/phy/phy-qcom-8x16-usb.c:284:13: error: 'regs[0].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/usb/phy/phy-qcom-8x16-usb.c:285:13: error: 'regs[1].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/usb/phy/phy-qcom-8x16-usb.c:286:12: error: 'regs[2].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
According to Mark Brown, this is the result of various abuses
of the PHY interfaces [1], so let's fix the driver instead.
This puts the regulator bulk data into the device structure so it
gets properly initialized and lets us call regulator_bulk_enable()
and regulator_bulk_disable() rather than open-coding them.
Setting the voltages the way the driver does is rather pointless
because for each regulator there is only one valid voltage
range, so that can just get set up in the DT. As there doesn't
seem to be any user of the newly added driver yet, we can simply
make sure the DTs are setting this up right when they get added.
I'm also fixing the handling of regulator_bulk_enable() failure.
Right now, the driver just ignores any failure, which doesn't make
sense, so I'm changing it to loudly complain (in case we actually
had a bug here) and error out.
Doing a fly-by review of the driver, I notice a couple of other
problems that I'm not addressing here:
- It really should not have been written as a USB PHY driver, but
instead should use the PHY subsystem.
- The DT compatible string does not follow the usual conventions,
and it should have a proper identifier in it rather than a wildcard.
- The example in the devicetree binding lists a register address
that is the same as the actual EHCI host controller in the SoC
as well as the otg-snps and the ci-hdrc device, which indicates
that these are probably not even distinct devices (or all but
one of them are wrong), and if more than one of them tries to
request the resources correctly, they fail.
[1] https://lkml.org/lkml/2016/1/26/267
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Access multi-byte fields of the SSP Dev Cap descriptor using the correct
endianness.
Fixes: f228a8de24 ("usb: gadget: composite: Return SSP Dev Cap descriptor")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
UDC driver should NEVER do anything behind
udc-core's back, so let's stop disabling endpoints
we don't exactly own - rather we provide as
resources for gadget drivers. This fixes the
regression reported by Gil.
Reported-by: Gil Weber <gil.weber@servelec-technologies.com>
Tested-by: Gil Weber <gil.weber@servelec-technologies.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We were exitting the function before actually
renaming anything. While at that, also always leave
control endpoint un-renamed.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's a requirement that we release controller's lock
while calling gadget API function pointers. This
patch just fixes that long standing bug.
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook, we shouldn't be
relying on GCTL.CORESOFTRESET bit as that's only for
debugging purposes. Instead, let's use DCTL.CSFTRST
if we're OTG or PERIPHERAL mode.
Host side block will be reset by XHCI driver if
necessary. Note that this reduces amount of time
spent on dwc3_probe() by a long margin.
We're still gonna wait for reset to finish for a
long time (default to 1ms max), but tests show that
the reset polling loop executed at most 19 times
(modprobe dwc3 && modprobe -r dwc3 executed 1000
times in a row).
Suggested-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since f_midi_transmit is called by both ALSA and USB sub-systems, it can
potentially cause a race condition between both calls because f_midi_transmit
is not reentrant nor thread-safe. This is due to an implementation detail that
the transmit function looks for the next available usb request from the fifo
and only enqueues it if there is data to send, otherwise just re-uses it. So,
if both ALSA and USB frameworks calls this function at the same time,
kfifo_seek() will return the same usb_request, which will cause a race
condition.
To solve this problem a syncronization mechanism is necessary. In this case it
is used a spinlock since f_midi_transmit is also called by usb_request->complete
callback in interrupt context.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: e1e3d7ec5d ("usb: gadget: f_midi: pre-allocate IN requests")
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
new device support in terms of LoC, but there has been some cleanup
in the core as well as the usual minor clk additions to various
drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a minor
refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bZFY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add target_alloc_session() w/ callback helper for doing se_session
allocation + tag + se_node_acl lookup. (HCH + nab)
- Tree-wide fabric driver conversion to use target_alloc_session()
- Convert sbp-target to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Chris Boot + nab)
- Convert usb-gadget to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Andrzej Pietrasiewicz + nab)
- Convert xen-scsiback to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Juergen Gross + nab)
- Convert tcm_fc to use TARGET_SCF_ACK_KREF I/O + TMR krefs
- Convert ib_srpt to use percpu_ida tag pre-allocation
- Add DebugFS node for qla2xxx target sess list (Quinn)
- Rework iser-target connection termination (Jenny + Sagi)
- Convert iser-target to new CQ API (HCH)
- Add pass-through WRITE_SAME support for IBLOCK (Mike Christie)
- Introduce data_bitmap for asynchronous access of data area (Sheng
Yang + Andy)
- Fix target_release_cmd_kref shutdown comp leak (Himanshu Madhani)
Also, there is a separate PULL request coming for cxgb4 NIC driver
prerequisites for supporting hw iscsi segmentation offload (ISO), that
will be the base for a number of v4.7 developments involving
iscsi-target hw offloads"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
target: Fix target_release_cmd_kref shutdown comp leak
target: Avoid DataIN transfers for non-GOOD SAM status
target/user: Report capability of handling out-of-order completions to userspace
target/user: Fix size_t format-spec build warning
target/user: Don't free expired command when time out
target/user: Introduce data_bitmap, replace data_length/data_head/data_tail
target/user: Free data ring in unified function
target/user: Use iovec[] to describe continuous area
target: Remove enum transport_lunflags_table
target/iblock: pass WRITE_SAME to device if possible
iser-target: Kill the ->isert_cmd back pointer in struct iser_tx_desc
iser-target: Kill struct isert_rdma_wr
iser-target: Convert to new CQ API
iser-target: Split and properly type the login buffer
iser-target: Remove ISER_RECV_DATA_SEG_LEN
iser-target: Remove impossible condition from isert_wait_conn
iser-target: Remove redundant wait in release_conn
iser-target: Rework connection termination
iser-target: Separate flows for np listeners and connections cma events
iser-target: Add new state ISER_CONN_BOUND to isert_conn
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition
of a MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAVu67OmCrR//JCVInAQJ64hAAqNemdAMloJhh8mk4O74egd/XNE8GLK3v
gGefpZNi0TC8u/GWMhU1aFCElaCmbNlL0IlqaRrU/vydOmQcZYht7Fg3bAm4r3ck
TlKijGTJap4sdHhxSeui+7bhaBToxcklQTdcrKFgOwsype7CAWJCl5otIC/GHO5L
fn4QSjQbqr5kqH1XfuVIphj/fJjDKRRze5D7zn0nExq46OyoYyjc2lm/QkLgeeS2
vDpzOULYXcjf5GfsPknCJGGjenISD7cIAwZukGvJXFh8WrXkEPZZ7B7bBI/8ZeBU
MkdWvOm9fHEWpIPnuTcLeQNlfdzQ0Z0zijgJqnXjwSYXK2Es1UKEoIFvZUyGA9zG
uyLtddFcKbP4QBDUKVMbyYM6x4Cj7LO96dB2pe8iH5rvnoLS32EjJ/4glnbPQFB7
75JKb7eU1pijoy9c3x/G10vINHzbPjyUN3sYTFKMomPFzEF4OVQ3GDclSuD7jjDr
GnqmAqlj29+qGU6iQBBHp9TfLTxwrs/4MKPEZ+tTGvtINnzOpLGA3TUnji7nVFQc
BYy3qaEvg9MfHI3uXhAl2L4CGCVvHfqFs5B7giZfAkbbcTNAHs9PkZ6gMYH+GG3p
tEbTf/dMHmkkqttSz4f7LZS7D56cSfm3cD8kFCRJPLKifmGAk3w1HZ7JoCXdjr1K
22HSKRMxlhU=
=HS4G
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition of a
MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
bus: imx-weim: Take the 'status' property value into account
clk: at91: remove useless includes
clk: at91: pmc: remove useless capacities handling
clk: at91: pmc: drop at91_pmc_base
usb: gadget: atmel: access the PMC using regmap
ARM: at91: remove useless includes and function prototypes
ARM: at91: pm: move idle functions to pm.c
ARM: at91: pm: find and remap the pmc
ARM: at91: pm: simply call at91_pm_init
clk: at91: pmc: move pmc structures to C file
clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
clk: at91: remove IRQ handling and use polling
clk: at91: make use of syscon/regmap internally
clk: at91: make use of syscon to share PMC registers in several drivers
hwmon: (scpi) add energy meter support
firmware: arm_scpi: add support for 64-bit sensor values
firmware: arm_scpi: decrease Tx timeout to 20ms
firmware: arm_scpi: fix send_message and sensor_get_value for big-endian
reset: sti: Make reset_control_ops const
reset: zynq: Make reset_control_ops const
...
Merge second patch-bomb from Andrew Morton:
- a couple of hotfixes
- the rest of MM
- a new timer slack control in procfs
- a couple of procfs fixes
- a few misc things
- some printk tweaks
- lib/ updates, notably to radix-tree.
- add my and Nick Piggin's old userspace radix-tree test harness to
tools/testing/radix-tree/. Matthew said it was a godsend during the
radix-tree work he did.
- a few code-size improvements, switching to __always_inline where gcc
screwed up.
- partially implement character sets in sscanf
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
sscanf: implement basic character sets
lib/bug.c: use common WARN helper
param: convert some "on"/"off" users to strtobool
lib: add "on"/"off" support to kstrtobool
lib: update single-char callers of strtobool()
lib: move strtobool() to kstrtobool()
include/linux/unaligned: force inlining of byteswap operations
include/uapi/linux/byteorder, swab: force inlining of some byteswap operations
include/asm-generic/atomic-long.h: force inlining of some atomic_long operations
usb: common: convert to use match_string() helper
ide: hpt366: convert to use match_string() helper
ata: hpt366: convert to use match_string() helper
power: ab8500: convert to use match_string() helper
power: charger_manager: convert to use match_string() helper
drm/edid: convert to use match_string() helper
pinctrl: convert to use match_string() helper
device property: convert to use match_string() helper
lib/string: introduce match_string() helper
radix-tree tests: add test for radix_tree_iter_next
radix-tree tests: add regression3 test
...
Here is a USB fix for the reported issue with 69bec72598 "USB: core:
let USB device know device node" as well as some other issues that have
been reported so far with this merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbsjB8ACgkQMUfUDdst+yn5BACeK0uVt+S/pr+HQE30j67b4UV6
TcMAn25xKshM73AFDm9ok9qKnWEEvkEt
=UgYu
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a USB fix for the reported issue with commit 69bec72598
("USB: core: let USB device know device node") as well as some other
issues that have been reported so far with this merge window"
* tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: uas: Reduce can_queue to MAX_CMNDS
USB: cdc-acm: more sanity checking
USB: usb_driver_claim_interface: add sanity checking
usb/core: usb_alloc_dev(): fix setting of ->portnum
USB: iowarrior: fix oops with malicious USB descriptors
The uas driver can never queue more then MAX_CMNDS (- 1) tags and tags
are shared between luns, so there is no need to claim that we can_queue
some random large number.
Not claiming that we can_queue 65536 commands, fixes the uas driver
failing to initialize while allocating the tag map with a "Page allocation
failure (order 7)" error on systems which have been running for a while
and thus have fragmented memory.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Yves-Alexis Perez <corsac@corsac.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An attack has become available which pretends to be a quirky
device circumventing normal sanity checks and crashes the kernel
by an insufficient number of interfaces. This patch adds a check
to the code path for quirky devices.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attacks that trick drivers into passing a NULL pointer
to usb_driver_claim_interface() using forged descriptors are
known. This thwarts them by sanity checking.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iowarrior driver expects at least one valid endpoint. If given
malicious descriptors that specify 0 for the number of endpoints,
it will crash in the probe function. Ensure there is at least
one endpoint on the interface before using it.
The full report of this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/87
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
drivers/rtc: broken link fix
drm/i915 Fix typos in i915_gem_fence.c
Docs: fix missing word in REPORTING-BUGS
lib+mm: fix few spelling mistakes
MAINTAINERS: add git URL for APM driver
treewide: Fix typo in printk
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
- A large patch from me to simplify setting up the list of default
groups by actually implementing it as a list instead of an array.
- a small Y2083 prep patch from Deepa Dinamani. Probably doesn't matter
on it's own, but it seems like he is trying to get rid of all CURRENT_TIME
uses in file systems, which is a worthwhile goal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9HqT
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
- A large patch from me to simplify setting up the list of default
groups by actually implementing it as a list instead of an array.
- a small Y2083 prep patch from Deepa Dinamani. Probably doesn't
matter on it's own, but it seems like he is trying to get rid of all
CURRENT_TIME uses in file systems, which is a worthwhile goal.
* tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs:
configfs: switch ->default groups to a linked list
configfs: Replace CURRENT_TIME by current_fs_time()
The new helper returns index of the mathing string in an array. We
would use it here.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big USB patchset for 4.6-rc1.
The normal mess is here, gadget and xhci fixes and updates, and lots of
other driver updates and cleanups as well. Full details are in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8/EACgkQMUfUDdst+ylsyQCgnVK6ZIFVPV9VijJvBIjxS3F+
fTMAoIMQwNrRMHQOq/lhxX00AgN0B9Ch
=2EQp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.6-rc1.
The normal mess is here, gadget and xhci fixes and updates, and lots
of other driver updates and cleanups as well. Full details are in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (266 commits)
USB: core: let USB device know device node
usb: devio: Add ioctl to disallow detaching kernel USB drivers.
usb: gadget: f_acm: Fix configfs attr name
usb: udc: lpc32xx: remove USB PLL and USB OTG clock management
usb: udc: lpc32xx: remove direct access to clock controller registers
usb: udc: lpc32xx: switch to clock prepare/unprepare model
usb: renesas_usbhs: gadget: fix giveback status code in usbhsg_pipe_disable()
usb: gadget: renesas_usb3: Use ARCH_RENESAS
usb: dwc2: Fix issues in dwc2_complete_non_isoc_xfer_ddma()
usb: dwc2: Add support for Lantiq ARX and XRX SoCs
usb: phy: generic: Handle late registration of gadget
usb: gadget: bdc_udc: fix race condition in bdc_udc_exit()
usb: musb: core: added missing const qualifier to musb_hdrc_platform_data::config
usb: dwc2: Move host-specific core functions into hcd.c
usb: dwc2: Move register save and restore functions
usb: dwc2: Use kmem_cache_free()
usb: dwc2: host: If using uframe scheduler, end splits better
usb: dwc2: host: Totally redo the microframe scheduler
usb: dwc2: host: Properly set even/odd frame
usb: dwc2: host: Add dwc2_hcd_get_future_frame_number() call
...
Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8z8ACgkQMUfUDdst+ym1vwCgnOOCORaZyeQ4QrcxPAK5pHFn
VrMAoNHvDgNYtG+Hmzv25Lgp3HnysPin
=MLRG
-----END PGP SIGNATURE-----
Merge tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (220 commits)
serial: 8250: describe CONFIG_SERIAL_8250_RSA
serial: samsung: optimize UART rx fifo access routine
serial: pl011: add mark/space parity support
serial: sa1100: make sa1100_register_uart_fns a function
tty: serial: 8250: add MOXA Smartio MUE boards support
serial: 8250: convert drivers to use up_to_u8250p()
serial: 8250/mediatek: fix building with SERIAL_8250=m
serial: 8250/ingenic: fix building with SERIAL_8250=m
serial: 8250/uniphier: fix modular build
Revert "drivers/tty/serial: make 8250/8250_ingenic.c explicitly non-modular"
Revert "drivers/tty/serial: make 8250/8250_mtk.c explicitly non-modular"
serial: mvebu-uart: initial support for Armada-3700 serial port
serial: mctrl_gpio: Add missing module license
serial: ifx6x60: avoid uninitialized variable use
tty/serial: at91: fix bad offset for UART timeout register
tty/serial: at91: restore dynamic driver binding
serial: 8250: Add hardware dependency to RT288X option
TTY, devpts: document pty count limiting
tty: goldfish: support platform_device with id -1
drivers: tty: goldfish: Add device tree bindings
...
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.6:
API:
- Convert remaining crypto_hash users to shash or ahash, also convert
blkcipher/ablkcipher users to skcipher.
- Remove crypto_hash interface.
- Remove crypto_pcomp interface.
- Add crypto engine for async cipher drivers.
- Add akcipher documentation.
- Add skcipher documentation.
Algorithms:
- Rename crypto/crc32 to avoid name clash with lib/crc32.
- Fix bug in keywrap where we zero the wrong pointer.
Drivers:
- Support T5/M5, T7/M7 SPARC CPUs in n2 hwrng driver.
- Add PIC32 hwrng driver.
- Support BCM6368 in bcm63xx hwrng driver.
- Pack structs for 32-bit compat users in qat.
- Use crypto engine in omap-aes.
- Add support for sama5d2x SoCs in atmel-sha.
- Make atmel-sha available again.
- Make sahara hashing available again.
- Make ccp hashing available again.
- Make sha1-mb available again.
- Add support for multiple devices in ccp.
- Improve DMA performance in caam.
- Add hashing support to rockchip"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (116 commits)
crypto: qat - remove redundant arbiter configuration
crypto: ux500 - fix checks of error code returned by devm_ioremap_resource()
crypto: atmel - fix checks of error code returned by devm_ioremap_resource()
crypto: qat - Change the definition of icp_qat_uof_regtype
hwrng: exynos - use __maybe_unused to hide pm functions
crypto: ccp - Add abstraction for device-specific calls
crypto: ccp - CCP versioning support
crypto: ccp - Support for multiple CCPs
crypto: ccp - Remove check for x86 family and model
crypto: ccp - memset request context to zero during import
lib/mpi: use "static inline" instead of "extern inline"
lib/mpi: avoid assembler warning
hwrng: bcm63xx - fix non device tree compatibility
crypto: testmgr - allow rfc3686 aes-ctr variants in fips mode.
crypto: qat - The AE id should be less than the maximal AE number
lib/mpi: Endianness fix
crypto: rockchip - add hash support for crypto engine in rk3288
crypto: xts - fix compile errors
crypto: doc - add skcipher API documentation
crypto: doc - update AEAD AD handling
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tPgH
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Added support for some new video formats
- mn88473 DVB frontend driver got promoted from staging
- several improvements at the VSP1 driver
- several cleanups and improvements at the Media Controller
- added Media Controller support to snd-usb-audio. Currently, enabled
only for au0828-based V4L2/DVB boards
- Several improvements at nuvoton-cir: it now supports wake up codes
- Add media controller support to em28xx and saa7134 drivers
- coda driver now accepts NXP distributed firmware files
- Some legacy SoC camera drivers will be moving to staging, as they're
outdated and nobody so far is willing to fix and convert them to use
the current media framework
- As usual, lots of cleanups, improvements and new board additions.
* tag 'media/v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (381 commits)
media: au0828 disable tuner to demod link in au0828_media_device_register()
[media] touptek: cast char types on %x printk
[media] touptek: don't DMA at the stack
[media] mceusb: use %*ph for small buffer dumps
[media] v4l: exynos4-is: Drop unneeded check when setting up fimc-lite links
[media] v4l: vsp1: Check if an entity is a subdev with the right function
[media] hide unused functions for !MEDIA_CONTROLLER
[media] em28xx: fix Terratec Grabby AC97 codec detection
[media] media: add prefixes to interface types
[media] media: rc: nuvoton: switch attribute wakeup_data to text
[media] v4l2-ioctl: fix YUV422P pixel format description
[media] media: fix null pointer dereference in v4l_vb2q_enable_media_source()
[media] v4l2-mc.h: fix yet more compiler errors
[media] staging/media: add missing TODO files
[media] media.h: always start with 1 for the audio entities
[media] sound/usb: Use meaninful names for goto labels
[media] v4l2-mc.h: fix compiler warnings
[media] media: au0828 audio mixer isn't connected to decoder
[media] sound/usb: Use Media Controller API to share media resources
[media] dw2102: add support for TeVii S662
...
PCI-SIG has defined Interface FEh for Base Class 0Ch, Sub-Class 03h as "USB
Device (not host controller)". It is already being used in various USB
device controller drivers for matching, so add PCI_CLASS_SERIAL_USB_DEVICE
and use it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* commit '840f5b0572ea': (381 commits)
media: au0828 disable tuner to demod link in au0828_media_device_register()
[media] touptek: cast char types on %x printk
[media] touptek: don't DMA at the stack
[media] mceusb: use %*ph for small buffer dumps
[media] v4l: exynos4-is: Drop unneeded check when setting up fimc-lite links
[media] v4l: vsp1: Check if an entity is a subdev with the right function
[media] hide unused functions for !MEDIA_CONTROLLER
[media] em28xx: fix Terratec Grabby AC97 codec detection
[media] media: add prefixes to interface types
[media] media: rc: nuvoton: switch attribute wakeup_data to text
[media] v4l2-ioctl: fix YUV422P pixel format description
[media] media: fix null pointer dereference in v4l_vb2q_enable_media_source()
[media] v4l2-mc.h: fix yet more compiler errors
[media] staging/media: add missing TODO files
[media] media.h: always start with 1 for the audio entities
[media] sound/usb: Use meaninful names for goto labels
[media] v4l2-mc.h: fix compiler warnings
[media] media: au0828 audio mixer isn't connected to decoder
[media] sound/usb: Use Media Controller API to share media resources
[media] dw2102: add support for TeVii S662
...
This patch drops struct usbg_cmd->kref internal kref-erence
usage, for proper TARGET_SCF_ACK_KREF conversion.
Tested-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts usb-gadget target to use percpu_ida tag
pre-allocation for struct usbg_cmd descriptor, in order to
avoid fast-path struct usbg_cmd memory allocations.
Note by default this is currently hardcoded to 128.
Tested-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts existing loopback, usb-gadget, and
xen-scsiback demo-mode only fabric drivers to use the
new target_alloc_session API caller.
This includes adding a new alloc_session callback for
fabric driver internal nexus pointer assignments.
(Fixes for early for-next nexus breakage - Dan Carpenter)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Acked-by: Juergen Gross <jgross@suse.com>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here are some cp210x register-accessor updates and general usb-serial
code clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=9QeZ
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.6-rc1
Here are some cp210x register-accessor updates and general usb-serial
code clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
Replace the current NULL-terminated array of default groups with a linked
list. This gets rid of lots of nasty code to size and/or dynamically
allocate the array.
While we're at it also provide a conveniant helper to remove the default
groups.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Felipe Balbi <balbi@kernel.org> [drivers/usb/gadget]
Acked-by: Joel Becker <jlbec@evilplan.org>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Although most of USB devices are hot-plug's, there are still some devices
are hard wired on the board, eg, for HSIC and SSIC interface USB devices.
If these kinds of USB devices are multiple functions, and they can supply
other interfaces like i2c, gpios for other devices, we may need to
describe these at device tree.
In this commit, it uses "reg" in dts as physical port number to match
the phyiscal port number decided by USB core, if they are the same,
then the device node is for the device we are creating for USB core.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new USBDEVFS_DROP_PRIVILEGES ioctl allows a process to voluntarily
relinquish the ability to issue other ioctls that may interfere with
other processes and drivers that have claimed an interface on the
device.
This commit also includes a simple utility to be able to test the
ioctl, located at Documentation/usb/usbdevfs-drop-permissions.c
Example (with qemu-kvm's input device):
$ lsusb
...
Bus 001 Device 002: ID 0627:0001 Adomax Technology Co., Ltd
$ usb-devices
...
C: #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=02 Driver=usbhid
$ sudo ./usbdevfs-drop-permissions /dev/bus/usb/001/002
OK: privileges dropped!
Available options:
[0] Exit now
[1] Reset device. Should fail if device is in use
[2] Claim 4 interfaces. Should succeed where not in use
[3] Narrow interface permission mask
Which option shall I run?: 1
ERROR: USBDEVFS_RESET failed! (1 - Operation not permitted)
Which test shall I run next?: 2
ERROR claiming if 0 (1 - Operation not permitted)
ERROR claiming if 1 (1 - Operation not permitted)
ERROR claiming if 2 (1 - Operation not permitted)
ERROR claiming if 3 (1 - Operation not permitted)
Which test shall I run next?: 0
After unbinding usbhid:
$ usb-devices
...
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=02 Driver=(none)
$ sudo ./usbdevfs-drop-permissions /dev/bus/usb/001/002
...
Which option shall I run?: 2
OK: claimed if 0
ERROR claiming if 1 (1 - Operation not permitted)
ERROR claiming if 2 (1 - Operation not permitted)
ERROR claiming if 3 (1 - Operation not permitted)
Which test shall I run next?: 1
OK: USBDEVFS_RESET succeeded
Which test shall I run next?: 0
After unbinding usbhid and restricting the mask:
$ sudo ./usbdevfs-drop-permissions /dev/bus/usb/001/002
...
Which option shall I run?: 3
Insert new mask: 0
OK: privileges dropped!
Which test shall I run next?: 2
ERROR claiming if 0 (1 - Operation not permitted)
ERROR claiming if 1 (1 - Operation not permitted)
ERROR claiming if 2 (1 - Operation not permitted)
ERROR claiming if 3 (1 - Operation not permitted)
Signed-off-by: Reilly Grant <reillyg@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is almost all under drivers/usb/dwc2/. Many
changes to the host side implementation of dwc2 have
been done by Douglas Anderson.
We also have USB 3.1 support added to the Gadget
Framework and, because of that work, dwc3 got
support to Synopsys new DWC_usb31 IP core.
Other than these 2 important series, we also have
the usual collection of non-critical fixes,
Documentation updates, and minor changes all over
the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vivP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.6' of http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb changes for v4.6 merge window
This is almost all under drivers/usb/dwc2/. Many
changes to the host side implementation of dwc2 have
been done by Douglas Anderson.
We also have USB 3.1 support added to the Gadget
Framework and, because of that work, dwc3 got
support to Synopsys new DWC_usb31 IP core.
Other than these 2 important series, we also have
the usual collection of non-critical fixes,
Documentation updates, and minor changes all over
the place.
Correct attribute name is port_num not num.
Fixes: ea6bd6b ("usb-gadget/f_acm: use per-attribute show and store methods")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
LPC32xx common clock framework driver correctly manages parent clocks
of USB device clock, so there is no need to manually enable and
disable them from the driver, which now depends only on a single USB
device clock.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Direct access to clock control registers can be safely removed, the
task of clock management is done by platform clock driver based on
common clock framework.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The driver requires to prepare/unprepare clocks to work properly on a
platform with enabled common clock framework, otherwise unprepared
clocks are not enabled:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:728 clk_core_enable+0x2c/0xf0()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #284
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xf0)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_udc_probe+0x284/0x924)
[<>] (lpc32xx_udc_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (__platform_driver_probe+0x54/0x100)
[<>] (__platform_driver_probe) from [<>] (lpc32xx_udc_driver_init+0x1c/0x28)
[<>] (lpc32xx_udc_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A udc driver should set the giveback status to -ESHUTDOWN in
usb_ep_disable(). Otherwise, a gadget driver (e.g. g_serial) might
request next data wrongly and it is possible to cause kernel panic.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes a static analysis issue in dwc2_complete_non_isoc_xfer_ddma(). The
qtd was being passed to a function after being freed. It was not being
used in the function so this doesn't fix any bugs. But it fixes up the
warning and makes the code safer by setting qtd to NULL and not using it
at all.
Reported-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add support for Lantiq ARX and XRX SoC families to the dwc2 driver.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is possible for the VBUS detect GPIO interrupt to occur before
nop_set_peripheral() is called, in which case otg->gadget is NULL.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
bdc_ep_disable() expects to be called with bdc->lock held.
The assumption is met in all the cases except for call from bdc_udc_exit(),
that is called from bdc_remove(). As a result a race can happen or unheld
bdc->lock can be unlocked in bdc_req_complete().
The patch proposes to acquire-release bdc->lock around bdc_ep_disable()
in bdc_udc_exit().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The musb_hdrc_platform_data::config was defined as a non-const pointer.
However some drivers (e.g. the ux500) set up this pointer to point to a
static structure, which is potentially dangerous. Since the musb core
uses the pointer in a read-only manner the const qualifier was added to
protect the content of the config.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Move host core initialization and host channel routines into hcd.c. This
allows these functions to only be compiled in host-enabled driver
configurations (DRD or host-only).
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Move the register save and restore functions into the host and gadget
specific files.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Here, free memory is allocated using kmem_cache_zalloc. So, use
kmem_cache_free instead of kfree.
This is done using Coccinelle and semantic patch used
is as follows:
//<smpl>
@@
expression x,E,c;
@@
x =
\(kmem_cache_alloc\|kmem_cache_zalloc\|kmem_cache_alloc_node\)(c,...)
... when != x = E
when != &x
?-kfree(x)
+kmem_cache_free(c,x)
//</smpl>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The microframe scheduler figured out exactly how many transfers we need
for a split transaction. Let's use this knowledge to know when to end
things.
Without this I found that certain devices would just keep responding
with tons of NYET resonses on their INT_IN endpoint. These would just
keep going and going and eventually we'd decide to terminate the
transfer (because the whole frame changed), but by that time the
scheduler would decide that we "missed" the start of the next transfer.
I can also imagine that if we blow past the end of our scheduled time we
may mess up other things that were scheduled to happen.
No known test cases are improved by this patch except that the scheduler
code doesn't yell about MISSES constantly anymore.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This totally reimplements the microframe scheduler in dwc2 to attempt to
handle periodic splits properly. The old code didn't even try, so this
was a significant effort since periodic splits are one of the most
complicated things in USB.
I've attempted to keep the old "don't use the microframe" schduler
around for now, but not sure it's needed. It has also only been lightly
tested.
I think it's pretty certain that this scheduler isn't perfect and might
have some bugs, but it seems much better than what was there before.
With this change my stressful USB test (USB webcam + USB audio + some
keyboards) crackles less.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When setting up ISO and INT transfers dwc2 needs to specify whether the
transfer is for an even or an odd frame (or microframe if the controller
is running in high speed mode).
The controller appears to use this as a simple way to figure out if a
transfer should happen right away (in the current microframe) or should
happen at the start of the next microframe. Said another way:
- If you set "odd" and the current frame number is odd it appears that
the controller will try to transfer right away. Same thing if you set
"even" and the current frame number is even.
- If the oddness you set and the oddness of the frame number are
_different_, the transfer will be delayed until the frame number
changes.
As I understand it, the above technique allows you to plan ahead of time
where possible by always working on the next frame. ...but it still
allows you to properly respond immediately to things that happened in
the previous frame.
The old dwc2_hc_set_even_odd_frame() didn't really handle this concept.
It always looked at the frame number and setup the transfer to happen in
the next frame. In some cases that meant that certain transactions
would be transferred in the wrong frame.
We'll try our best to set the even / odd to do the transfer in the
scheduled frame. If that fails then we'll do an ugly "schedule ASAP".
We'll also modify the scheduler code to handle this and not try to
schedule a second transfer for the same frame.
Note that this change relies on the work to redo the microframe
scheduler. It can work atop ("usb: dwc2: host: Manage frame nums better
in scheduler") but it works even better after ("usb: dwc2: host: Totally
redo the microframe scheduler").
With this change my stressful USB test (USB webcam + USB audio +
keyboards) has less audio crackling than before.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As we start getting more exact about our scheduling it's becoming more
and more important to know exactly how far through the current frame we
are. This lets us make decisions about whether there's still time left
to start a new transaction in the current frame.
We'll add dwc2_hcd_get_future_frame_number() which will tell you what
the frame number will be a certain number of microseconds (us) from
now. We can use this information to help decide if there's enough time
left in the frame for a transaction that will take a certain duration.
This is expected to be used by a future change ("usb: dwc2: host:
Properly set even/odd frame").
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The dwc2 scheduler (contained in hcd_queue.c) was a bit confusing in the
way it initted / kept track of which frames a QH was going to be active
in. Let's clean things up a little bit in preparation for a rewrite of
the microframe scheduler.
Specifically:
* Old code would pick a frame number in dwc2_qh_init() and would try to
pick it "in a slightly future (micro)frame". As far as I can tell the
reason for this was that there was a delay between dwc2_qh_init() and
when we actually wanted to dwc2_hcd_qh_add(). ...but apparently this
attempt to be slightly in the future wasn't enough because
dwc2_hcd_qh_add() then had code to reset things if the frame _wasn't_
in the future. There's no reason not to just pick the frame later.
For non-periodic QH we now pick the frame in dwc2_hcd_qh_add(). For
periodic QH we pick the frame at dwc2_schedule_periodic() time.
* The old "dwc2_qh_init() actually assigned to "hsotg->frame_number".
This doesn't seem like a great idea since that variable is supposed to
be used to keep track of which SOF the interrupt handler has seen.
Let's be clean: anyone who wants the current frame number (instead of
the one as of the last interrupt) should ask for it.
* The old code wasn't terribly consistent about trying to use the frame
that the microframe scheduler assigned to it. In
dwc2_sched_periodic_split() when it was scheduling the first frame it
always "ORed" in 0x7 (!). Since the frame goes on the wire 1 uFrame
after next_active_frame it meant that the SSPLIT would always try for
uFrame 0 and the transaction would happen on the low speed bus during
uFrame 1. This is irregardless of what the microframe scheduler
said.
* The old code assumed it would get called to schedule the next in a
periodic split very quickly. That is if next_active_frame was
0 (transfer on wire in uFrame 1) it assumed it was getting called to
schedule the next uFrame during uFrame 1 too (so it could queue
something up for uFrame 2). It should be possible to actually queue
something up for uFrame 2 while in uFrame 2 (AKA queue up ASAP). To
do this, code needs to look at the previously scheduled frame when
deciding when to next be active, not look at the current frame number.
* If there was no microframe scheduler, the old code would check for
whether we should be active using "qh->next_active_frame ==
frame_number". This seemed like a race waiting to happen. ...plus
there's no way that you wouldn't want to schedule if next_active_frame
was actually less than frame number.
Note that this change doesn't make 100% sense on its own since it's
expecting some sanity in the frame numbers assigned by the microframe
scheduler and (as per the future patch which rewries it) I think that
the current microframe scheduler is quite insane. However, it seems
like splitting this up from the microframe scheduler patch makes things
into smaller chunks and hopefully adds to clarity rather than reduces
it. The two patches could certainly be squashed. Not that in the very
least, I don't see any obvious bad behavior introduced with just this
patch.
I've attempted to keep the config parameter to disable the microframe
scheduler in tact in this change, though I'm not sure it's worth it.
Obviously the code is touched a lot so it's possible I regressed
something when the microframe scheduler is disabled, though I did some
basic testing and it seemed to work OK. I'm still not 100% sure why you
wouldn't want the microframe scheduler (presuming it works), so maybe a
future patch (or a future version of this patch?) could remove that
parameter.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We'll use the new "scheduler verbose debugging" macro to log missed
SOFs. This is fast enough (assuming you configure it to use the ftrace
buffer) that we can do it without worrying about the speed hit. The
overhead hit if the scheduler tracing is set to "no_printk" should be
near zero.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This no-op change splits code out of dwc2_schedule_periodic() into a
dwc2_do_reserve() function. This makes it a little easier to follow the
logic.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This no-op change just reorders a few functions in hcd_queue.c in order
to prepare for future changes. Motivations here:
The functions dwc2_hcd_qh_free() and dwc2_hcd_qh_create() are exported
functions. They are not called within the file. That means that they
should be near the bottom so that they can easily call static helpers.
The function dwc2_qh_init() is only called by dwc2_hcd_qh_create() and
should move near the bottom with it.
The only reason that the dwc2_unreserve_timer_fn() timer function (and
its subroutine dwc2_do_unreserve()) were so high in the file was that
they needed to be above dwc2_qh_init(). Now that dwc2_qh_init() has
been moved down it can be moved down a bit. A later patch will split
the reserve code out of dwc2_schedule_periodic() and the reserve
function should be near the unreserve function. The reserve function
needs to be below dwc2_find_uframe() since it calls that.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This no-op change just does some renames to simplify a future patch.
1. The "interval" field is renamed to "host_interval" to make it more
obvious that this interval may be 8 times the interval that the
device sees (if we're doing split transactions). A future patch will
also add the "device_interval" field.
2. The "usecs" field is renamed to "host_us" again to make it more
obvious that this is the time for the transaction as seen by the
host. For split transactions the device may see a much longer
transaction time. A future patch will also add "device_us".
3. The "sched_frame" field is renamed to "next_active_frame". The name
"sched_frame" kept confusing me because it felt like something more
permament (the QH's reservation or something). The name
"next_active_frame" makes it more obvious that this field is
constantly changing.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The old code in dwc2_process_periodic_channels() would only enable the
"periodic empty" interrupt if we weren't using DMA. That wasn't right
since we can still get into cases where we have small FIFOs even on
systems that have DMA (the rk3288 is a prime example).
Let's always enable/disable the "periodic empty" when appropriate. As
part of this:
* Always call dwc2_process_periodic_channels() even if there's nothing
in periodic_sched_assigned (we move the queue empty check so we still
avoid the extra work). That will make extra certain that we will
properly disable the "periodic empty" interrupt even if there's
nothing queued up.
* Move the enable of "periodic empty" due to non-empty
periodic_sched_assigned to be for slave mode (non-DMA mode) only.
Presumably this was the original intention of the check for DMA since
it seems to match the comments above where in slave mode we leave
things on the assigned queue.
Note that even before this change slave mode didn't work for me, so I
can't say for sure that my understanding of slave mode is correct.
However, this shouldn't change anything for slave mode so if slave mode
worked for someone in the past it ought to still work.
With this change, I no longer get constant misses reported by my other
debugging code (and with future patches) when I've got:
* Rockchip rk3288 Chromebook, using port ff540000
-> Pluggable 7-port Hub with Charging (powered)
-> Microsoft Wireless Keyboard 2000 in port 1.
-> Das Keyboard in port 2.
-> Jabra Speaker in port 3
-> Logitech, Inc. Webcam C600 in port 4
-> Microsoft Sidewinder X6 Keyboard in port 5
...and I'm playing music on the USB speaker and capturing video from the
webcam.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
I find that when I plug a full speed (NOT high speed) hub into a dwc2
port and then I plug a bunch of devices into that full speed hub that
dwc2 goes bat guano crazy. Specifically, it just spews errors like this
in the console:
usb usb1: clear tt 1 (9043) error -22
The specific test case I used looks like this:
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
|__ Port 1: Dev 17, If 0, Class=Hub, Driver=hub/4p, 12M
|__ Port 2: Dev 19, If 0, ..., Driver=usbhid, 1.5M
|__ Port 4: Dev 20, If 0, ..., Driver=usbhid, 12M
|__ Port 4: Dev 20, If 1, ..., Driver=usbhid, 12M
|__ Port 4: Dev 20, If 2, ..., Driver=usbhid, 12M
Showing VID/PID:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 017: ID 03eb:3301 Atmel Corp. at43301 4-Port Hub
Bus 001 Device 020: ID 045e:0745 Microsoft Corp. Nano Transceiver ...
Bus 001 Device 019: ID 046d:c404 Logitech, Inc. TrackMan Wheel
I spent a bunch of time trying to figure out why there are errors to
begin with. I believe that the issue may be a hardware issue where the
transceiver sometimes accidentally sends a PREAMBLE packet if you send a
packet to a full speed device right after one to a low speed device.
Luckily the USB driver retries and the second time things work OK.
In any case, things kinda seem work despite the errors, except for the
"clear tt" spew mucking up my console. Chalk it up for a win for
retries and robust protocols.
So getting back to the "clear tt" problem, it appears that we get those
because there's not actually a TT here to clear. It's my understanding
that when dwc2 operates in low speed or full speed mode that there's no
real TT out there. That makes all these attempts to "clear the TT"
somewhat meaningless and also causes the spew in the log.
Let's just skip all the useless TT clears. Eventually we should root
cause the errors, but even if we do this is still a proper fix and is
likely to avoid the "clear tt" error in the future.
Note that hooking up a Full Speed USB Audio Device (Jabra 510) to this
same hub with the keyboard / trackball shows that even audio works over
this janky connection. As a point to note, this particular change (skip
bogus TT clears) compared to just commenting out the dev_err() in
hub_tt_work() actually produces better audio.
Note: don't ask me where I got a full speed USB hub or whether the
massive amount of dust that accumulated on it while it was in my junk
box affected its funtionality. Just smile and nod.
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
In case you didn't spot it, the difference is the "- 1".
Let's add the "- 1" to match the newest user manual. It's presumed that
the "- 1" should have always been there and that this was always a
documentation error. If some hardware needs the "- 1" and other
hardware doesn't, we'll have to add a configuration parameter for it in
the future.
I checked things before and after this patch on rk3288 using a Total
Phase Beagle 5000 analyzer.
Before this patch, a low speed mouse shows constant Frame Timing Jitter
errors. After this patch errors have gone away.
Before this patch SOF packets move forward about 1 us per 4 ms. After
this patch the SOF packets move backward about 1 us per 255 ms. Some
specific SOF timestamps from the analyzer are below.
Before:
6.603.790
6.603.916
6.604.041
6.604.166
...
6.607.541
6.607.667
6.607.792
6.607.917
...
6.611.417
6.611.543
6.611.668
6.611.793
After:
6.215.159
6.215.284
6.215.408
6.215.533
6.215.658
...
6.470.658
6.470.783
6.470.907
...
6.726.032
6.726.157
6.725.281
6.725.406
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In commit 94dfd7edfd ("USB: HCD: support giveback of URB in tasklet
context") support was added to give back the URB in tasklet context.
Let's take advantage of this in dwc2.
This speeds up the dwc2 interrupt handler considerably.
Note that this requires the change ("usb: dwc2: host: Add a delay before
releasing periodic bandwidth") to come first.
Note that, as per Alan Stern in
<https://patchwork.kernel.org/patch/7555771/>, we also need to make sure
that the extra delay before the device drivers submit more data doesn't
break the scheduler. At the moment the scheduler is pretty broken (see
future patches) so it's hard to be 100% certain, but I have yet to see
any new breakage introduced by this delay. ...and speeding up interrupt
processing for dwc2 is a huge deal because it means we've got a better
chance of not missing SOF interrupts. That means we've got an overall
win here.
Note that when playing USB audio and using a USB webcam and having
several USB keyboards plugged in, the crackling on the USB audio device
is noticably reduced with this patch.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We'd like to be able to use HCD_BH in order to speed up the dwc2 host
interrupt handler quite a bit. However, according to the kernel doc for
usb_submit_urb() (specifically the part about "Reserved Bandwidth
Transfers"), we need to keep a reservation active as long as a device
driver keeps submitting. That was easy to do when we gave back the URB
in the interrupt context: we just looked at when our queue was empty and
released the reserved bandwidth then. ...but now we need a little more
complexity.
We'll follow EHCI's lead in commit 9118f9eb4f ("USB: EHCI: improve
interrupt qh unlink") and add a 5ms delay. Since we don't have a whole
timer infrastructure in dwc2, we'll just add a timer per QH. The
overhead for this is very small.
Note that the dwc2 scheduler is pretty broken (see future patches to fix
it). This patch attempts to replicate all old behavior and just add the
proper delay.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In preparation for future changes to the scheduler let's add some
tracing that makes it easy for us to see what's happening. By default
this tracing will be off.
By changing "core.h" you can easily trace to ftrace, the console, or
nowhere.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We're supposed to keep outstanding splits in order. Keep track of a
list of the order of splits and process channel interrupts in that
order.
Without this change and the following setup:
* Rockchip rk3288 Chromebook, using port ff540000
-> Pluggable 7-port Hub with Charging (powered)
-> Microsoft Wireless Keyboard 2000 in port 1.
-> Das Keyboard in port 2.
...I find that I get dropped keys on the Microsoft keyboard (I'm sure
there are other combinations that fail, but this documents my test).
Specifically I've been typing "hahahahahahaha" on the keyboard and often
see keys dropped or repeated.
After this change the above setup works properly. This patch is based
on a previous patch proposed by Yunzhi Li ("usb: dwc2: hcd: fix periodic
transfer schedule sequence")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The queues the the dwc2 host controller used are truly queues. That
means FIFO or first in first out.
Unfortunately though the code was iterating through these queues
starting from the head, some places in the code was adding things to the
queue by adding at the head instead of the tail. That means last in
first out. Doh.
Go through and just always add to the tail.
Doing this makes things much happier when I've got:
* 7-port USB 2.0 Single-TT hub
* - Microsoft 2.4 GHz Transceiver v7.0 dongle
* - Jabra speakerphone playing music
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When poking around with USB devices with slub_debug enabled, I found
another obvious use after free. Turns out that in dwc2_hc_n_intr() I
was in a state when the contents of chan->qh was filled with 0x6b,
indicating that chan->qh was freed but chan still had a reference to
it.
Let's make sure that whenever we free qh we also make sure we remove a
reference from its channel.
The bug fixed here doesn't appear to be new--I believe I just got lucky
and happened to see it while stress testing.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As documented in dwc2_calculate_dynamic_fifo(), host_rx_fifo_size should
really be:
2 * ((Largest Packet size / 4) + 1 + 1) + n
with n = number of host channel.
We have 9 host channels, so
2 * ((1024/4) + 2) + 9 = 516 + 9 = 525
We've got 960 / 972 total_fifo_size on rk3288 (and presumably on
rk3066) and 525 + 128 + 256 = 909 so we're still under on both ports
even when we increment by 5.
In the future, it would be nice if dwc2_calculate_dynamic_fifo() could
handle the "too small" FIFO case and come up with something more
dynamically. When we do that we can figure out how to allocate the
extra 48 / 60 bytes of FIFO that we're currently wasting.
NOTE: no known bugs are fixed by this patch, but it seems like a simple
fix and ought to fix someone.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
All other host controllers who want aligned buffers for DMA do it a
certain way. Let's do that too instead of working behind the USB core's
back. This makes our interrupt handler not take forever and also rips
out a lot of code, simplifying things a bunch.
This also has the side effect of removing the 65535 max transfer size
limit.
NOTE: The actual code to allocate the aligned buffers is ripped almost
completely from the tegra EHCI driver. At some point in the future we
may want to add this functionality to the USB core to share more code
everywhere.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: John Youn <johnyoun@synopsys.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Previously we needed to set the max_transfer_size to explicitly be 65535
because the old driver would detect that our hardware could support much
bigger transfers and then would try to do them. This wouldn't work
since the DMA alignment code couldn't support it.
Later in commit e8f8c14d9d ("usb: dwc2: clip max_transfer_size to
65535") upstream added support for clipping this automatically. Since
that commit it has been OK to just use "-1" (default), but nobody
bothered to change it.
Let's change it to default now for two reasons:
- It's nice to use autodetected params.
- If we can remove the 65535 limit, we can transfer more!
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Check that dwc->maximum_speed is set to a valid value. Also add an error
when we use it later if we encounter an invalid value.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
MODULE_DEVICE_TABLE() is missing, so the module isn't auto-loading on
sunxi systems using the OTG controller. This commit adds the missing
line so it loads automatically when building it as a module and running
on a system with an USB OTG port.
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
B-device detects that bus is idle for more than TB_AIDL_BDIS min and
begins HNP by turning off pullup on DP, this allows the bus to discharge
to the SE0 state. This timer was missed and failed with PET test:
6.8.5 B-UUT HNP of USB OTG and EH automated compliance plan v1.2,
this patch is to fix this timing issue.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable HNP polling support for chipidea gadget and allocate memory
for host request flag when otg fsm init.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Set host_request_flag if the current peripheral wants to take host role
via changing a_bus_req or b_bus_req by user application.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If gadget with HNP polling support receives GetStatus request of otg
status selector, it feedback to host with host request flag to indicate
if it wants to take host role.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since gadget driver will handle this request, so controller driver bypass
it.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Adds HNP polling timer when transits to host state, the OTG status
request will be sent to peripheral after timeout, if host request flag
is set, it will switch to peripheral state, otherwise it will repeat HNP
polling every 1.5s and maintain the current session.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since commit 855ed04a37 ("usb: gadget:
udc-core: independent registration of gadgets and gadget drivers") gadget
drivers can not assume that UDC drivers are already available on their
initialization. This broke the HACK, which was used in gadgetfs driver,
to get UDC controller name. This patch removes this hack and replaces it
by additional function in the UDC core (which is usefully only for legacy
drivers, please don't use it in the new code).
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
For every in_substream, there must be a corresponding gmidi_in_port
structure so it is perfectly viable and some might argue sensible to
stash pointer to the input substream in the gmidi_in_port structure.
This has an added benefit that if in_ports < MAX_PORTS, the whole
f_midi structure takes up less space because only in_ports number of
pointers for in_substream are allocated instead of MAX_PORTS lots of
them.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We added a new error path to this function and we forgot to drop the
lock.
Fixes: e1e3d7ec5d ('usb: gadget: f_midi: pre-allocate IN requests')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[mina86@mina86.com: rebased on top of refactoring commit]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Reduce number of allocations, simplify memory management and reduce
memory usage by stacking the gmidi_in_port elements at the end of the
f_midi structure using a flexible array.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In general case, all of midi->in_port pointers may be non-NULL which
implies that the ‘if (\!port)’ condition will never execute thus never
zeroing midi->in_last_port. Fix by rewriting the loop such that the
field is set to zero if \!port or end of loop has been reached.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Move some of the f_midi_transmit to a separate f_midi_do_transmit
function so the massive indention levels are not so jarring. This
introduces no changes in behaviour.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
remove a field which is unnecessary. No functional changes.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
ffs_epfile_io and ffs_epfile_io_complete runs in different context, but
there is no synchronization between them.
consider the following scenario:
1) ffs_epfile_io interrupted by sigal while
wait_for_completion_interruptible
2) then ffs_epfile_io set ret to -EINTR
3) just before or during usb_ep_dequeue, the request completed
4) ffs_epfile_io return with -EINTR
In this case, ffs_epfile_io tell caller no transfer success but actually
it may has been done. This break the caller's pipe.
Below script can help test it (adbd is the process which lies on f_fs).
while true
do
pkill -19 adbd #SIGSTOP
pkill -18 adbd #SIGCONT
sleep 0.1
done
To avoid this, just dequeue the request first. After usb_ep_dequeue, the
request must be done or canceled.
With this change, we can ensure no race condition in f_fs driver. But
actually I found some of the udc driver has analogical issue in its
dequeue implementation. For example,
1) the dequeue function hold the controller's lock.
2) before driver request controller to stop transfer, a request
completed.
3) the controller trigger a interrupt, but its irq handler need wait
dequeue function to release the lock.
4) dequeue function give back the request with negative status, and
release lock.
5) irq handler get lock but the request has already been given back.
So, the dequeue implementation should take care of this case. IMO, it
can be done as below steps to dequeue a already started request,
1) request controller to stop transfer on the given ep. HW know the
actual transfer status.
2) after hw stop transfer, driver scan if there are any completed one.
3) if found, process it with real status. if no, the request can
canceled.
Signed-off-by: "Du, Changbin" <changbin.du@intel.com>
[mina86@mina86.com: rebased on top of refactoring commits]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Eliminate one of the return paths by using a ‘goto error_mutex’ and
rearrange some if-bodies which results in reduction of the indention level
and thus hopefully makes the function easier to read and reason about.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In ffs_epfile_io error label points to a return path which includes
a kfree(data) call. However, at the beginning of the function data is
always NULL so some of the early ‘goto error’ can safely be replaced
with a trivial return statement.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In the AIO path, if allocating of a request failse, the function simply
goes to the error_lock path whose end result is returning value of ret.
However, at this point ret’s value is zero (assigned as return value from
ffs_mutex_lock).
Fix by adding ‘ret = -ENOMEM’ statement.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In the ffs_epfile_io function, data buffer is allocated for non-halt
requests. Later, after grabing a mutex, the function checks that
epfile->ep is still ep and if it’s not, it set ret to -ESHUTDOWN and
follow a path including spin_unlock_irq (just after ‘ret = -ESHUTDOWN’),
mutex_unlock (after if-else-if-else chain) and returns ret. Noticeably,
this does not include freeing of the data buffer.
Fix by introducing a goto which moves control flow to the the end of the
function where spin_unlock_irq, mutex_unlock and kfree are all called.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
phy-am335x.c doesn't use any interfaces from linux/regulator/consumer.h, so
stop including it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When I wrote the cleanup patch series, it was not clear how
exactly big-endian mode works on ixp4xx, and whether the driver
was doing this correctly. After discussing with Krzysztof Hałasa,
this has been clarified, so I can update the comment let pxa25x
big-endian (which we don't support) work the same way as ixp4xx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When dma_addr_t is 64-bit, we get a warning about an invalid cast
in the call to ux500_dma_is_compatible() from ux500_dma_channel_program():
drivers/usb/musb/ux500_dma.c: In function 'ux500_dma_channel_program':
drivers/usb/musb/ux500_dma.c:210:51: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
if (!ux500_dma_is_compatible(channel, packet_sz, (void *)dma_addr, len))
The problem is that ux500_dma_is_compatible() is called from the
main musb driver on the virtual address, but here we pass in a
DMA address, so the types are fundamentally different but it works
because the function only checks the alignment of the buffer and
that is the same.
We could work around this by adding another cast, but I have checked
that the buffer we get passed here is already checked before it
gets mapped, so the second check seems completely unnecessary
and removing it must be the cleanest solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The musb driver prints DMA addresses in a few places, using the
0x%x format string. This is wrong on 64-bit architectures (which
need %lx) and 32-bit ARM with CONFIG_LPAE set (which needs
%llx), otherwise we print the wrong data, as gcc warns:
musb/musbhsdma.c: In function 'configure_channel':
musb/musbhsdma.c:120:53: error: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
dev_dbg(musb->controller, "%p, pkt_sz %d, addr 0x%x, len %d, mode %d\n",
musb/musbhsdma.c: In function 'dma_channel_program':
musb/musbhsdma.c:155:53: error: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
dev_dbg(musb->controller, "ep%d-%s pkt_sz %d, dma_addr 0x%x length %d, mode %d\n",
musb/tusb6010_omap.c: In function 'tusb_omap_dma_program':
musb/tusb6010_omap.c:313:53: error: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
dev_dbg(musb->controller, "ep%i %s dma ch%i dma: %08x len: %u(%u) packet_sz: %i(%i)\n",
This uses the %pad format string, which prints a dma_addr_t that
gets passed by reference, which works for all combinations.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The power_up function is used for otg or udc mode, but nost when
the driver is only configured for host mode:
drivers/usb/phy/phy-isp1301-omap.c:261:13: error: 'power_up' defined but not used [-Werror=unused-function]
This marks the function __maybe_unused to avoid the warning and
silently drop the definition when it is unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The USB_FSL_MPH_DR_OF symbol is used to ensure the code that interprets
the DR device node is built whenever one of the two drivers (EHCI or
UDC) for the platform is enabled. However, if CONFIG_USB is disabled
and we only support gadget mode, this causes a Kconfig warning:
warning: (USB_FSL_USB2) selects USB_FSL_MPH_DR_OF which has unmet direct dependencies (USB_SUPPORT && USB)
We can avoid this warning by simply no longer using the symbol,
and making sure we enter the drivers/usb/host/ directory when
the UDC driver is enabled that needs the file, and then we use
Makefile syntax to ensure the file is built-in if needed.
There is currently a dependency on CONFIG_OF, but this is redundant,
as we already know that this is set unconditionally for the platforms
that use this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This converts the pxa25x udc driver to use readl/writel as normal
driver should do, rather than dereferencing __iomem pointers
themselves.
Based on the earlier preparation work, we can now also pass
the register start in the device pointer so we no longer need
the global variable.
The unclear part here is for IXP4xx, which supports both big-endian
and little-endian configurations. So far, the driver has done
no byteswap in either case. I suspect that is wrong and it would
actually need to swap in one or the other case, but I don't know
which. It's also possible that there is some magic setting in
the chip that makes the endianess of the MMIO register match the
CPU, and in that case, the code actually does the right thing
for all configurations, both before and after this patch.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This removes the dependency on the mach/hardware.h header file
from the pxa25x_udc driver after the register definitions were
already unified in the previous patch.
Following the model of pxa27x_udc (and basically all other drivers
in the kernel), we define the register numbers as offsets from
the register base address and use accessor functions to read/write
them.
For the moment, this still leaves the direct pointer dereference
in place, instead of using readl/writel, so this patch should
not be changing the behavior of the driver, other than using
ioremap() on the platform resource to replace the hardcoded
virtual address pointers.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
ixp4xx and pxa25x both use this driver and provide a slightly
different set of register definitions for it. Aside from that,
the definition in the ixp4xx-regs.h header conflicts with the
on in the pxa27x device driver when compile-testing that:
In file included from ../drivers/usb/gadget/udc/pxa27x_udc.c:37:0:
../drivers/usb/gadget/udc/pxa27x_udc.h:26:0: warning: "UDCCR" redefined
#define UDCCR 0x0000 /* UDC Control Register */
^
In file included from ../arch/arm/mach-ixp4xx/include/mach/hardware.h:27:0,
from ../arch/arm/mach-ixp4xx/include/mach/io.h:18,
from ../arch/arm/include/asm/io.h:194,
from ../include/linux/io.h:25,
from ../include/linux/irq.h:24,
from ../drivers/usb/gadget/udc/pxa27x_udc.c:23:
../arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h:415:0: note: this is the location of the previous definition
#define UDCCR IXP4XX_USB_REG(IXP4XX_USB_BASE_VIRT+0x0000)
This addresses both issues by moving all the definitions into the
pxa25x_udc driver itself. It turns out the only difference between
them was 'UDCCS_IO_ROF', and that could well be a mistake when it
was incorrectly copied from pxa25x to ixp4xx.
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since Some SoCs (e.g. R-Car Gen2) don't have the CSSTS bit in the
pipectrl registers ({DCP,PIPEn}CTR) because such SoCs have peripheral
mode only. So, this driver should not check the CSSTS bit if peripheral
mode is running.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since the usb2 phy driver for gen3 (phy-rcar-gen3-usb2) cannot access
LPSTS and UGCTRL2 registers in the HSUSB module, this driver have to
initialize the registers. So, this patch adds such handling code into
rcar3.c.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable SuperSpeedPlus by programming the DCFG.speed and after
enumerating, set gadget->speed appropriately.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the maximum_speed is not set, set it to a known value, either
SuperSpeed or SuperSpeedPlus based on the type of controller we are
using. If we are on DWC_usb31 controller, check the PHY interface to see
if it is capable of SuperSpeedPlus.
Also this check is moved after dwc3_core_init() so that we can check
dwc->revision.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update various places where the speed is checked so that it takes into
account SuperSpeedPlus properly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update various registers fields definitions for the DWC_usb31 controller
for SuperSpeedPlus support.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add a convenience function to check if the controller is DWC_usb31.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable superspeed plus configuration for the mass storage gadget.
The mass storage function doesn't do anything special for
SuperSpeedPlus. Just pass in the same SuperSpeed descriptors for
SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update the debug message reporting the speeds that a configuration
supports for SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Configure the usb_ep using the SuperSpeedPlus descriptors if connected
in SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable writing of SuperSpeedPlus descriptors for any SuperSpeedPlus
capable configuration when connected in SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There are a couple places in the code that get the function descriptors
based on the speed. Move this lookup into a function call and add
support to handle the SuperSpeedPlus descriptors as well.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If enumerated in SuperSpeedPlus, count the configurations that support
it.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When a function is added to a configuration with usb_add_function(), the
configuration speed flags are updated. These flags indicate for which
speeds the configuration is valid for.
This patch adds a flag in the configuration for SuperSpeedPlus and
also updates this based on the existence of ssp_descriptors.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add a ssp_descriptors member to struct usb_function and handle the
initialization and cleanup of it. This holds the SuperSpeedPlus
descriptors for a function that supports SuperSpeedPlus. This is added
by usb_assign_descriptors().
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add the 'ssp_descriptors' parameter to the usb_assign_descriptors()
function. This allows a function driver to add descriptors for
SuperSpeedPlus speeds if it supports it.
Also update all uses of this function in the gadget subsystem so that
they pass NULL for the ssp_descriptors parameters.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a gadget supports SuperSpeedPlus or higher speeds, return a
SuperSpeedPlus USB Device Capability descriptor.
Currently this implementation returns a fixed descriptor with typical
values set.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The USB 3.1 specification replaces the USB 3.0 specification and all new
devices that are running at SuperSpeed or higher speeds must report a
bcdUSB of 0x0310.
Refer to USB 3.1 Specification, Revision 1.0, Section 9.6.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
LPC32xx common clock framework driver correctly manages parent clocks
of USB OHCI clock, so there is no need to manually enable and
disable them from the driver, which now depends only on a single USB
host clock.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct access to clock control registers can be safely removed, the
task of clock management is done by platform clock driver based on
common clock framework.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci-atmel driver uses #ifdef to check for CONFIG_PM, but then
uses SIMPLE_DEV_PM_OPS, which leaves the references out when
CONFIG_PM_SLEEP is not defined, so we get a warning with
PM=y && PM_SLEEP=n:
drivers/usb/host/ehci-atmel.c:189:12: error: 'ehci_atmel_drv_suspend' defined but not used [-Werror=unused-function]
drivers/usb/host/ehci-atmel.c:203:12: error: 'ehci_atmel_drv_resume' defined but not used [-Werror=unused-function]
This removes the incorrect #ifdef and instead uses a __maybe_unused
annotation to let the compiler know it can silently drop
the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ohci-at91 driver uses #ifdef to check for CONFIG_PM, but then
uses SIMPLE_DEV_PM_OPS, which leaves the references out when
CONFIG_PM_SLEEP is not defined, so we get a warning with
PM=y && PM_SLEEP=n:
drivers/usb/host/ohci-at91.c:587:1: error: 'ohci_hcd_at91_drv_suspend' defined but not used [-Werror=unused-function]
drivers/usb/host/ohci-at91.c:631:12: error: 'ohci_hcd_at91_drv_resume' defined but not used [-Werror=unused-function]
This removes the incorrect #ifdef and instead uses a __maybe_unused
annotation to let the compiler know it can silently drop
the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mediatek XHCI glue driver uses SET_SYSTEM_SLEEP_PM_OPS() to
conditionally set the correct suspend/resume options, and
also puts both the dev_pm_ops and the functions inside of
an #ifdef testing for CONFIG_PM_SLEEP, but those functions
then call other code that becomes unused:
drivers/usb/host/xhci-mtk.c:135:12: error: 'xhci_mtk_host_disable' defined but not used [-Werror=unused-function]
drivers/usb/host/xhci-mtk.c:313:13: error: 'usb_wakeup_enable' defined but not used [-Werror=unused-function]
drivers/usb/host/xhci-mtk.c:321:13: error: 'usb_wakeup_disable' defined but not used [-Werror=unused-function]
This replaces the #ifdef with __maybe_unused annotations so the
compiler knows it can silently drop them instead of warning.
For the DEV_PM_OPS definition, we can use an IS_ENABLED() check
to avoid defining the structure when CONFIG_PM is not set without
the #ifdef.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to hide function declarations, and making
these visible to the SoC specific host drivers lets us
use __maybe_unused and IS_ENABLED() checks to control
their use, rather than having to use #ifdef to hide all
callers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbip_protocol.txt, a document which describes usbip's
inner workings is currently located in the projects source
directory (drivers/usb/usbip/...). This patch moves it to
Documentation/usb.
This discussion was brought up by Guy Harris [0] during the
review of the USBIP dissector I wrote. For anyone interested:
support is available with the latest wireshark master/dev tree.
Simply select a packet from the usbip's tcp-stream you are
intrested on and select the USBIP as the protocol in the
"Decode As" dialog box [1].
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[0] <https://bugs.wireshark.org/bugzilla/show_bug.cgi?id=12127#c2>
[1] <https://www.wireshark.org/docs/wsug_html_chunked/ChCustProtocolDissectionSection.html#ChAdvDecodeAs>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_autopm_put_interface() should be called regardless of what
idmouse_create_image() returns.
Signed-off-by: Junjie Mao <junjie.mao@enight.me>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A typo of j for i led to a logic bug. To rule out future
confusion, the variable names are made meaningful.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add fallback compatibility strings for R-Car Gen2 and Gen3.
This is in keeping with the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids and a patch removing the mxu11x0 driver,
which turned out not to be needed.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=f2SZ
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Jonan writes:
USB-serial fixes for v4.5-rc7
Here are some new device ids and a patch removing the mxu11x0 driver,
which turned out not to be needed.
Signed-off-by: Johan Hovold <johan@kernel.org>
MODULE_DEVICE_TABLE() is missing, so the module isn't auto-loading on
sunxi systems using the OTG controller. This commit adds the missing
line so it loads automatically when building it as a module and running
on a system with an USB OTG port.
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The MC74xx and EM74xx modules use different IDs by default, according
to the Lenovo EM7455 driver for Windows.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 0b2b093ad4.
Turns out the MOXA vendor driver was basically just a copy of the
ti_usb_3410_5052 driver. We don't want two drivers for the same chip
even if mxu11x0 had gotten some much needed clean up before merge. So
let's remove the mxu11x0 driver, add support for these Moxa devices to
the TI driver, and then clean that driver up instead.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for 0x1045 PID of Telit LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
cp210x_get_config and cp210x_set_config are cumbersome to use. This change
switches large register access to use new block functions. The old
functions are removed because now they become unused.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: minor style change ]
Signed-off-by: Johan Hovold <johan@kernel.org>
cp210x_get_config and cp210x_set_config are cumbersome to use. This change
introduces new register access functions for 8 and 32-bit values, instead
of the above functions.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
cp210x_get_config and cp210x_set_config are cumbersome to use. This change
introduces new register access functions for 16-bit values, instead of
the above functions.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Parrot NMEA GPS Flight Recorder is a USB composite device
consisting of hub, flash storage, and cp210x usb to serial chip.
It is an accessory to the mass-produced Parrot AR Drone 2.
The device emits standard NMEA messages which make the it compatible
with NMEA compatible software. It was tested using gpsd version 3.11-3
as an NMEA interpreter and using the official Parrot Flight Recorder.
Signed-off-by: Vittorio Alfieri <vittorio88@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Avoid printing an error if adding the device failes with return
value EPROBE_DEFFER. This may happen e.g. due to missing GPIO for
the vbus-supply regulator.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In chipidea IP RTL, there is a very limited design for siTD, the detail
like below:
There is no Max Packet Size at siTD, so it uses one constant for both
Max Packet Size for packet and the packet size for the last transaction
when considering schedule.
If the ttctrl.ttha does not match against Hub Address field in siTD,
this constant is 188 bytes, else this constant is 1023 bytes.
If the ttctrl.ttha is non-zero value, RTL will use 188 as this constant,
so it will lose the data if the packet size is larger than 188 bytes, eg,
if we playback a wav which format is 48khz, 16 bits, 2 channels, the
packet size will be 192bytes, but the controller will only send 188 bytes
for this packet, the noise will be heared using USB audio card.
The use case is single transaction, but higher frame rate.
If the ttctr.ttha is zero value, we can send 1023 bytes within one
transaction, but the controller will not accept the coming tranaction
if it considers the schedule time is less than 1023 bytes. So the
limitation is we can't schedule as many as transactions within frame.
If the total bytes is already 256 bytes for previous transactions within
frame, it can't accept another transaction. The use case is multiple
transactions, but less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
retval is assigned to be -EOVERFLOW but is overwritten later before
it's used, remove this unused value assignment.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Until now the imx23 uses the imx27 platform flag. But the
imx23 needs the flag CI_HDRC_TURN_VBUS_EARLY_ON, too. So
fix this by adding a separate platform flag.
Suggested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Bool initializations should use true and false. Bool tests don't need
comparisons.
Also, use IS_ENABLED instead of ifdef.
Generated by: scripts/coccinelle/misc/boolinit.cocci
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove unneeded variables when "0" can be returned.
Generated by: scripts/coccinelle/misc/returnvar.cocci
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Move constants to the right of binary operators where it increases
readability.
Generated by: scripts/coccinelle/misc/compare_const_fl.cocci
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[johan: drop some chunks and fix others, amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The check for < 0 is impossible now that
of_clk_get_parent_count() returns an unsigned int. Simplify the
code and update the types.
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Big PMC rework that touches clk, PM, usb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJWxSJHAAoJEKbNnwlvZCyzEGsQALRmJvHYqYNPRgHKHlFGV4Uh
KuDuT0O/hVQqf1WB+gXt6E2WbDTzU+QGV8jux2zvZdi4ExdjZBTM9o1iQrORRyr0
AHcXsNRkbZ5t7mNp1WVQGMCmK3M/cuN2BmtPQzozmFyo4UNlPzxH7//DbhbrLxqI
zuYmxs5z1RMflIJTo4LfJGXzo6QzwrsRmiPANIr9niICa51F6x0HYMZTn1IMMGG/
KbJ9Rx8fOEqRgCo9LIvJPZa4jvFNjyqQN74qqX66XZW3LBJK4M5q+F/LUaw6M7Bi
7KVc47yRTujGOEHz/jhsf4IVbkUg1vidicIL1VMz9xjD1ZbjjCr0pdFlU/76r4BB
Ot2alkE56+zSAbpBaWGQ9nih97GF/vpwlD+qeGs+UwhmF69wmTOrtSEi1uL+gRzM
sdGXhQtMVPHJuK9fuZBP4bjgnAryZSpJHk/7VcEJ7rvuyXgXZGKdqN3lt8hjWyoi
SuOQ+mqpt726o1fGA8/kKwr/Po6BhYBYLw1SAJjBZ5BF4fTi+9d2Q1C/M8F9X0wE
UMXYfTkr4URDiNLFh8vyJoq/B0pN7FxtcPtaSoaCZO2jP5rXn36Axre35Si76WTb
ndT4YlSKCwOrhk84on2ym3yHEwOCJndB7F+CqiA2t/qool4aD2vcqDzlmeZoUT8r
qMB7zXbgpZ1ezqm6RKUB
=V4yQ
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.6-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/drivers
From Alexandre Belloni:
"This is a rework of the PMC driver. It touches multiple subsystems so
the easiest path is through arm-soc."
drivers update for 4.6:
- Big PMC rework that touches clk, PM, usb
* tag 'at91-ab-4.6-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
clk: at91: remove useless includes
clk: at91: pmc: remove useless capacities handling
clk: at91: pmc: drop at91_pmc_base
usb: gadget: atmel: access the PMC using regmap
ARM: at91: remove useless includes and function prototypes
ARM: at91: pm: move idle functions to pm.c
ARM: at91: pm: find and remap the pmc
ARM: at91: pm: simply call at91_pm_init
clk: at91: pmc: move pmc structures to C file
clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
clk: at91: remove IRQ handling and use polling
clk: at91: make use of syscon/regmap internally
clk: at91: make use of syscon to share PMC registers in several drivers
Signed-off-by: Olof Johansson <olof@lixom.net>
The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5QjC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.5-rc6' of http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.5-rc6
The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
Commit ac33cdb166 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When working in Dual Role Device mode, USB state machine is not kicked,
when host or gadget drivers are loaded. Fix this be explicitly triggering
state detection on client driver load.
Issue is that if the board is booted without micro usb cable and usb
device attached, kernel fails to populate the usb host and device.
The reason for this is that the state machine worker logic only checks
for USB_DR_MODE_PERIPHERAL and USB_DR_MODE_HOST modes to run worker
thread. However if the phy is configured in OTG mode it would fail
to run the state machine, resulting in failure to detect for very
first time.
This patch fixes the issue by removing the explicit checks.
Issue is noticed on Qualcomm Dragon board DB410C.
[srinivas.kandagatla@linaro.org: Added more details to log]
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: Simon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some platforms don't have DMA, but we should still be able to build USB
drivers for these platforms. They could still be used through vhci_hcd,
usbip_host, or maybe something like USB passthrough in UML from a
capable host.
If NO_DMA=y:
ERROR: "dma_pool_destroy" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "bad_dma_ops" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_free" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_alloc" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_create" [drivers/usb/core/usbcore.ko] undefined!
Add a few checks for CONFIG_HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The US_DEBUGPX macro uses printk without specifying a kernel log level, so
the default kernel log level is used, which may not match LOGLEVEL_DEBUG
used in usb_stor_dbg. Remove the macro and use usb_store_dbg instead.
Signed-off-by: Victor Dodon <printesoi@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the device is disconnected poll waiters were not being woken.
Changes for v2:
- add commit summary
- add Fixes and Reported-by tags
Fixes: eb6b92ecc0 ("Add support for receiving USBTMC USB488 SRQ notifications via poll/select")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write value is 8bit, but currently writing a larger number (eg a doubled
digit) is not errored but instead gets cast and sets off an action probably
undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow for and clean handling of signals an URB is introduced.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shares the cleanup code between all probe failure paths, instead of
having per-failure cleanup at each point in the function.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 4b61b4f205.
As reported by Oliver, this change was unnecessary.
Reported-by: Oliver Neukum <oneukum@suse.com>
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d8f00cd685.
Tony writes:
This upstream commit is causing an oops:
d8f00cd685 ("usb: hub: do not clear BOS field during reset device")
This patch has already been included in several -stable kernels. Here
are the affected kernels:
4.5.0-rc4 (current git)
4.4.2
4.3.6 (currently in review)
4.1.18
3.18.27
3.14.61
How to reproduce the problem:
Boot kernel with slub debugging enabled (otherwise memory corruption
will cause random oopses later instead of immediately)
Plug in USB 3.0 disk to xhci USB 3.0 port
dd if=/dev/sdc of=/dev/null bs=65536
(where /dev/sdc is the USB 3.0 disk)
Unplug USB cable while dd is still going
Oops is immediate:
Reported-by: Tony Battersby <tonyb@cybernetics.com>
Cc: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=eFQw
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.5-rc5
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
In case of error, the function usb_phy_generic_register()
returns ERR_PTR() and never returns NULL. The NULL test in
the return value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The write value is 8bit, but currently writing a larger number
(eg a doubled digit) is not errored but instead gets cast and
sets off an action probably undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
(Change the style of commit log to fix checkpatch.pl warning)
Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use regmap to access the PMC to avoid using at91_pmc_read and
at91_pmc_write.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.
There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There will be data toggle error happen for full speed buld-out transfer.
The data toggle bit is saved in qh for non-control transfers, it is wrong
to check the qtd for that case.
Also fix one static analysis tool issue after fix the data toggle error.
John Youn:
* Added WARN() to warn on improper usage of the
dwc2_hcd_save_data_toggle() function.
Signed-off-by: Dyson Lee <dyson.lee@intel.com>
Signed-off-by: Tang, Jianqiang <jianqiang.tang@intel.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes memory manipulation issues and makes Host DDMA bulk transfers
work.
dwc2_process_non_isoc_desc() must return non zero value ONLY when
failure happens in one of the queued descriptors. After receiving
non zero value the caller must stop processing of remaining
QTDs and their descriptors from chain.
Commit 26a19ea699 ("usb: dwc2: host: fix use of qtd after
free in desc dma mode") breaks non_isoc transaction completion logic
in Host DDMA mode. There were bugs before that, but after this patch
dwc2_process_non_isoc_desc() returns fail status even if descriptor
was processed normally. This causes break from loop which is processing
remaining descriptors assigned to QTD, which is not correct for QTDs
containing more than one descriptor.
Current dwc2 driver gathers queued BULK URBs until receiving URB
without URB_NO_INTERRUPT flag. Once getting it, SW creates
descriptor chain, stores it in qh structure and passes start
address to HW. Multiple URB data is contained in that chain.
Hence on getting error on descriptor after its processing by HW,
SW should go out of both loops(qh->qtd, qtd->descs) and report
the failure.
Fixes: 26a19ea699 ("usb: dwc2: host: fix use of qtd after free in desc dma mode")
Cc: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes an issue found on rockchip rk3036 and rk3188 SOC platforms. For
some reason, the existing msleep(25) is not enough after the force mode.
The following patch was reported to fix the issue.
This does increase the probe delay again slightly, but not up to the
level it was before the original series of patches that this fixes. It
does not cause any other issues when tested on Synopsys HAPS and Altera
socfpga platforms.
Need to revisit this series next release to see if we can address these
issues without having an unconditional delay.
Fixes: 09c96980dc ("usb: dwc2: Add functions to set and clear force mode")
Reported-by: Caesar Wang <caesar.upstream@gmail.com>
Reported-by: Michael Niewoehner <linux@mniewoehner.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Caesar Wang <caesar.upstream@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix spelling typos found in printk and Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some devices I got show an inability to operate right after
power on if they are already connected. They are beyond recovery
if the descriptors are requested multiple times. So in case of
a timeout we rather bail early and reset again. But it must be
done only on the first loop lest we get into a reset/time out
spiral that can be overcome with a retry.
This patch is a rework of a patch that fell through the cracks.
http://www.spinics.net/lists/linux-usb/msg103263.html
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new interface for userspace to preallocate memory that can be
used with usbfs. This gives two primary benefits:
- Zerocopy; data no longer needs to be copied between the userspace
and the kernel, but can instead be read directly by the driver from
userspace's buffers. This works for all kinds of transfers (even if
nonsensical for control and interrupt transfers); isochronous also
no longer need to memset() the buffer to zero to avoid leaking kernel data.
- Once the buffers are allocated, USB transfers can no longer fail due to
memory fragmentation; previously, long-running programs could run into
problems finding a large enough contiguous memory chunk, especially on
embedded systems or at high rates.
Memory is allocated by using mmap() against the usbfs file descriptor,
and similarly deallocated by munmap(). Once memory has been allocated,
using it as pointers to a bulk or isochronous operation means you will
automatically get zerocopy behavior. Note that this also means you cannot
modify outgoing data until the transfer is complete. The same holds for
data on the same cache lines as incoming data; DMA modifying them at the
same time could lead to your changes being overwritten.
There's a new capability USBDEVFS_CAP_MMAP that userspace can query to see
if the running kernel supports this functionality, if just trying mmap() is
not acceptable.
Largely based on a patch by Markus Rechberger with some updates. The original
patch can be found at:
http://sundtek.de/support/devio_mmap_v0.4.diff
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/built-in.o: In function `ehci_platform_probe':
/home/vegard/linux/drivers/usb/host/ehci-platform.c:282: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `oxu_drv_probe':
/home/vegard/linux/drivers/usb/host/oxu210hp-hcd.c:3821: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `isp1362_probe':
/home/vegard/linux/drivers/usb/host/isp1362-hcd.c:2668: undefined reference to `devm_ioremap_resource'
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC drivers/usb/host/xhci-mtk.o
drivers/usb/host/xhci-mtk.c:135:12: warning: ‘xhci_mtk_host_disable’ defined but not used [-Wunused-function]
static int xhci_mtk_host_disable(struct xhci_hcd_mtk *mtk)
^
drivers/usb/host/xhci-mtk.c:313:13: warning: ‘usb_wakeup_enable’ defined but not used [-Wunused-function]
static void usb_wakeup_enable(struct xhci_hcd_mtk *mtk)
^
drivers/usb/host/xhci-mtk.c:321:13: warning: ‘usb_wakeup_disable’ defined but not used [-Wunused-function]
static void usb_wakeup_disable(struct xhci_hcd_mtk *mtk)
^
CC drivers/usb/host/sl811-hcd.o
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_remove’:
drivers/usb/host/sl811-hcd.c:1607:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(sl811->data_reg);
^
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_probe’:
drivers/usb/host/sl811-hcd.c:1669:3: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
addr_reg = ioremap(addr->start, 1);
^
drivers/usb/host/sl811-hcd.c:1669:12: warning: assignment makes pointer from integer without a cast [enabled by default]
addr_reg = ioremap(addr->start, 1);
^
drivers/usb/host/sl811-hcd.c:1675:12: warning: assignment makes pointer from integer without a cast [enabled by default]
data_reg = ioremap(data->start, 1);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC drivers/usb/c67x00/c67x00-drv.o
drivers/usb/c67x00/c67x00-drv.c: In function ‘c67x00_drv_probe’:
drivers/usb/c67x00/c67x00-drv.c:148:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
c67x00->hpi.base = ioremap(res->start, resource_size(res));
^
drivers/usb/c67x00/c67x00-drv.c:148:19: warning: assignment makes pointer from integer without a cast [enabled by default]
c67x00->hpi.base = ioremap(res->start, resource_size(res));
^
drivers/usb/c67x00/c67x00-drv.c:185:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(c67x00->hpi.base);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC drivers/usb/musb/tusb6010.o
drivers/usb/musb/tusb6010.c: In function ‘tusb_musb_init’:
drivers/usb/musb/tusb6010.c:1133:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
sync = ioremap(mem->start, resource_size(mem));
^
drivers/usb/musb/tusb6010.c:1133:7: warning: assignment makes pointer from integer without a cast [enabled by default]
sync = ioremap(mem->start, resource_size(mem));
^
drivers/usb/musb/tusb6010.c:1162:4: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(sync);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC drivers/usb/host/r8a66597-hcd.o
drivers/usb/host/r8a66597-hcd.c: In function ‘r8a66597_remove’:
drivers/usb/host/r8a66597-hcd.c:2401:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(r8a66597->reg);
^
drivers/usb/host/r8a66597-hcd.c: In function ‘r8a66597_probe’:
drivers/usb/host/r8a66597-hcd.c:2447:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
reg = ioremap(res->start, resource_size(res));
^
drivers/usb/host/r8a66597-hcd.c:2447:6: warning: assignment makes pointer from integer without a cast [enabled by default]
reg = ioremap(res->start, resource_size(res));
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/host/xhci-mvebu.c: In function ‘xhci_mvebu_mbus_init_quirk’:
drivers/usb/host/xhci-mvebu.c:58:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
base = ioremap(res->start, resource_size(res));
^
drivers/usb/host/xhci-mvebu.c:58:7: warning: assignment makes pointer from integer without a cast [enabled by default]
base = ioremap(res->start, resource_size(res));
^
drivers/usb/host/xhci-mvebu.c:69:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(base);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/udc/m66592-udc.c: In function ‘m66592_remove’:
drivers/usb/gadget/udc/m66592-udc.c:1538:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(m66592->reg);
^
drivers/usb/gadget/udc/m66592-udc.c: In function ‘m66592_probe’:
drivers/usb/gadget/udc/m66592-udc.c:1577:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
reg = ioremap(res->start, resource_size(res));
^
drivers/usb/gadget/udc/m66592-udc.c:1577:6: warning: assignment makes pointer from integer without a cast [enabled by default]
reg = ioremap(res->start, resource_size(res));
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/udc/net2272.c: In function ‘net2272_remove’:
drivers/usb/gadget/udc/net2272.c:2232:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(dev->base_addr);
^
drivers/usb/gadget/udc/net2272.c: In function ‘net2272_plat_probe’:
drivers/usb/gadget/udc/net2272.c:2650:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
dev->base_addr = ioremap_nocache(base, len);
^
drivers/usb/gadget/udc/net2272.c:2650:17: warning: assignment makes pointer from integer without a cast [enabled by default]
dev->base_addr = ioremap_nocache(base, len);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/host/isp116x-hcd.c: In function ‘isp116x_remove’:
drivers/usb/host/isp116x-hcd.c:1552:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(isp116x->data_reg);
^
drivers/usb/host/isp116x-hcd.c: In function ‘isp116x_probe’:
drivers/usb/host/isp116x-hcd.c:1604:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
addr_reg = ioremap(addr->start, resource_size(addr));
^
drivers/usb/host/isp116x-hcd.c:1604:11: warning: assignment makes pointer from integer without a cast [enabled by default]
addr_reg = ioremap(addr->start, resource_size(addr));
^
drivers/usb/host/isp116x-hcd.c:1613:11: warning: assignment makes pointer from integer without a cast [enabled by default]
data_reg = ioremap(data->start, resource_size(data));
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In several drivers in the pxa architecture, it was found that the
platform_get_irq() was not propagated. This breaks the the device-tree
probe deferral path, if -EPROBE_DEFER is returned. Unfortunately, the
error return in this case is transformed into -ENXIO, breaking the
deferral mechanism.
Even if in this specific case the driver was not broken, because the
interrupt controller is always probed before drivers, propagate the
proper return code.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should cut down latencies and waste if the tty layer writes single bytes.
Signed-off-by: Oliver Neukum >oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transfer burst count (TBC) field in the Isoc TRB does not fit the new
larger burst count available for USB 3.1 SSP Isoc tranfers.
xhci 1.1 solved this by reusing the TD size field for transfer burst count.
The Mult field was outgrown as well. xhci 1.1 controllers can calculate
Mult itself and is not set if the new layout is used.
xhci 1.1 controllers that support the new Isoc TRB format expose a
Extended TBC Capability (ETC). To take the new format into use the xhci
host controller driver needs to set a Extended TBC Enable (ETE) bit.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up xhci_queue_isoc_tx() and helpers to prepare them for USB 3.1 and
xhci 1.1 isoc TRB changes.
Only functional change is adding xhci version 1.1 to the BEI flag check
toghether with xhci version 1.0. Both versions behave the same.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SuperSpeedPlus doubled the number of transactions per service interval
the isoc endpoints supports.
To support this, xhci 1.1 added Large ESIT Capability (LEC), which
takes into use new bits in the endpoint context to fit the parameters.
If xhci supports LEC, and the device has a SuperSpeedPlus Isoc companion
descriptor then take into use the high bits of max esit payload, and
skip calculating the Mult field as it wouldn't fit. LEC capable
host will calculate the Mult based on other paramenters.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_endpoint_init() and helper functions were a bit messy.
Adding the higher bandwidth SuperSpeedPlus Isoc support on
top of it would make it even harder to read.
No functional changes.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.1 devices that support precision time measurement have an
additional PTM cabaility descriptor as part of the full BOS descriptor
Look for this descriptor while parsing the BOS descriptor, and store it in
struct usb_hub_bos if it exists.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.1 devices can return a new SuperSpeedPlus isoc endpoint companion
descriptor for a isochronous endpoint that requires more than 48K bytes
per Service Interval.
The new descriptor immediately follows the old USB 3.0 SuperSpeed Endpoint
Companion and will provide a new BytesPerInterval value.
It is parsed and stored in struct usb_host_endpoint with the other endpoint
related descriptors, and should be used by USB3.1 capable hosts to reserve
bus time in the schedule.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixing the error reported by script checkpatch.pl
static variables blinkenlights and old_scheme_first
were initialised to 0, correcting it.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that usb_bus_list has been removed and switched to idr
rename the related mutex accordingly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers should include asm/pci-bridge.h only when they need the arch-
specific things provided there. Outside of the arch/ directories, the only
drivers that actually need things provided by asm/pci-bridge.h are the
powerpc RPA hotplug drivers in drivers/pci/hotplug/rpa*.
Remove the includes of asm/pci-bridge.h from the other drivers, adding an
include of linux/pci.h if necessary.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
xhci_find_next_ext_cap doesn't check for PCI hotplug removal and may use
the PCI master abort bit pattern (~0) to calculate a new PCI address
offset to read/write. The has lead to reproducable crashes when testing
surprise removal during device initialization on a Stratus platform, at
least after commit d5ddcdf4d6 ("xhci: rework xhci extended capability
list parsing functions").
The crash is repeatable on a Stratus platform when injecting hardware
faults to induce xHCI host controller hotplug during driver
initialization. If a PCI read in xhci_find_next_ext_cap returns the
master abort pattern, quirk_usb_handoff_xhci may start using a bogus
ext_cap_offset to start searching more bogus PCI addresses.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 got a fix for OTG Certification, DWC2 has two fixes for regressions on
RasPI, MUSB has a NULL pointer dereference fix for ux500 platforms and two
PHYs (MSM and MXS) got some minor fixes.
While at that, I'm also adding a fix to my email address which has changed
recently.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Zhyq
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.5-rc2
DWC3 got a fix for OTG Certification, DWC2 has two fixes for regressions on
RasPI, MUSB has a NULL pointer dereference fix for ux500 platforms and two
PHYs (MSM and MXS) got some minor fixes.
While at that, I'm also adding a fix to my email address which has changed
recently.
Fix the following compiler warning (found by the kbuild test robot):
drivers/usb/host/ehci-hcd.c:312:13: warning: 'unlink_empty_async_suspended' declared 'static' but never defined
Commit 2a40f32454 ("USB: EHCI: fix regression during bus resume")
protected the function definition with a "#ifdef CONFIG_PM" block, so
now the declaration needs to be similarly protected. This patch moves
it to a better location.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver frees data for all devices, both usb2 and and usb3 the
first time usb_remove_hcd() is called, including td_list and and xhci_ring
structures.
When usb_remove_hcd() is called a second time for the second xhci bus it
will try to dequeue all pending urbs, and touches td_list which is already
freed for that endpoint.
Cc: <stable@vger.kernel.org>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During probe, in the device tree case, the data pointer associated to a
compatible is dereferenced. However, not all the compatibles are
associated to a private data pointer.
The generic-xhci and the xhci-platform don't need them, this patch adds a
test on the data pointer before accessing it, avoiding a kernel crash.
Fixes: 4efb2f6941 ("usb: host: xhci-plat: add struct xhci_plat_priv")
Cc: stable@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when ip fails to enter sleep mode, register access protection will
be disabled, at the same time if all clocks are disabled, access
register will hang up AHB bus.
the common case causes ip sleep failure is that after all ports
enter U3 but before ip enters sleep mode, a port receives a resume
signal('K'). this will happens when such as clicks mouse to try to
do remote-wakeup to stop system enter suspend.
so stop polling root hubs to avoid access xHCI register on bus
suspend, and restart it when bus resumes.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when a LS or FS device doesn't connect though a HS hub,
the @bPkts field of its periodic endpoint context should
be set to 1.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Broxton M was verifed to require XHCI_PME_STUCK_QUIRK quirk as well.
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI_SSIC_PORT_UNUSED quirk was applied to the xHCI host controllers
in some Intel SoC chips. With this quirk applied, SSIC port is set
to "unused" prior to xhci_suspend(). This may cause problem if host
fails to suspend. In this case, the port is set to unused without
host further entering D3, and the port will not be usable anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two workarounds introduced by commit b8cb91e058 ("xhci: Workaround
for PME stuck issues in Intel xhci") and commit abce329c27 ("xhci:
Workaround to get D3 working in Intel xHCI") share a single quirk bit
XHCI_PME_STUCK_QUIRK. These two workarounds actually are different and
might happen on different hardwares. Need to separate them by adding a
quirk bit for the later.
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit abce329c27 ("xhci: Workaround to get D3 working in Intel xHCI")
adds a workaround for a limitation of PME storm caused by SSIC port in
some Intel SoCs. This commit only handled one SSIC port, while there
are actually two SSIC ports in the chips. This patch handles both SSIC
ports. Without this fix, users still see PME storm.
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is needed in order to pass one test case
defined in the OTG Automated Compliance Test specification.
Specification location:
http://www.usb.org/developers/onthego/otgeh_compliance_plan_1_2.pdf
This test case uses PET Tool, and PET Tool is one USB hardware
equipment provided by MQP Electronics.
Test case id is 6.8.3 B-UUT Bypass Capacitance.
We must set this otg flag in order to be able to return OTG
descriptor during enumeration, otherwise this test case with
failed with below error: "Get OTG descriptor request stalled".
Signed-off-by: Jianqiang Tang <jianqiang.tang@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit e210c422b6 ("xhci: don't finish a TD if we get a
short transfer event mid TD")
Turns out that most host controllers do not follow the xHCI specs and never
send the second event for the last TRB in the TD if there was a short event
mid-TD.
Returning the URB directly after the first short-transfer event is far
better than never returning the URB. (class drivers usually timeout
after 30sec). For the hosts that do send the second event we will go
back to treating it as misplaced event and print an error message for it.
The origial patch was sent to stable kernels and needs to be reverted from
there as well
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These ioctls provide support for the USBTMC-USB488 control requests
for REN_CONTROL, GO_TO_LOCAL and LOCAL_LOCKOUT
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a convenience function to obtain an instrument's
capabilities from its file descriptor without having to access sysfs
from the user program.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Background:
In many situations operations on multiple instruments need to be
synchronized. poll/select provide a convenient way of waiting on a
number of different instruments and other peripherals
simultaneously.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Background:
By configuring an instrument's event status register various
conditions can be reported via an SRQ notification. This complements
the synchronous polling approach using the READ_STATUS_BYTE ioctl
with an asynchronous notification.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Background:
When performing a read on an instrument that is executing a function
that runs longer than the USB timeout the instrument may hang and
require a device reset to recover. The READ_STATUS_BYTE operation
always returns even when the instrument is busy permitting to poll
for the appropriate condition. This capability is referred to in
instrument application notes on synchronizing acquisitions for other
platforms.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a privileged operation so it doesn't matter much. We use "tmp"
as an offset into an array. If it were invalid we could read out of
bounds and trigger an oops if the memory is not mapped. Plus it makes
static checkers complain.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecassary casts in the argument to kfree.
Found using Coccinelle. The semantic patch used to find this is as follows:
//<smpl>
@@
type T;
expression *f;
@@
- kfree((T *)(f));
+ kfree(f);
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes unnecessary braces in single statement blocks at the
same time as replaces the if statement with a ternary conditional.
Tested by compilation only.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds parens to sizeof operator uses.
Tested by compilation only.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a blank line after declarations.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes comments conforming coding style.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes an useless else branch after a break, reducing one
indent block.
Tested by compilation only.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes prohibited spaces before open parenthesis and open
brackets.
It also removes an assignment inside condition and unnecessary braces in
single statement block.
Tested by compilation only.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds spaces around operators.
Tested by compilation only.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes useless initializations.
Tested by compilation only.
Caught by cppcheck.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves the constants to right.
Tested by compilation only.
Caught by coccinelle:
scripts/coccinelle/misc/compare_const_fl.cocci
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes an infinite 'for' loop and makes use of the already
existing 'restart' tag instead, reducing one leading tab.
The comments and code were corrected conforming file coding style.
Tested by compilation only.
Caught by checkpatch:
WARNING: Too many leading tabs - consider code refactoring
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the local STUB_DEBUG_FILES debugging
definition. STUB_DEBUG_FILES was used only in ehci-hcd, whereas
CONFIG_DYNAMIC_DEBUG is used all over the kernel.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a coding style issue reported by checkpatch related to
too many leading tabs.
This moves part of the fill_periodic_buffer() to the new function
output_buf_tds_dir().
Because it's inline, the file size has not changed.
Before:
text data bss dec hex filename
36920 81 12 37013 9095 drivers/usb/host/ehci-hcd.o
After:
text data bss dec hex filename
36920 81 12 37013 9095 drivers/usb/host/ehci-hcd.o
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a coding style issue reported by checkpatch related to
kmalloc_array usage.
On the same line the sizeof operand was enclosed in parentheses.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch concerning
to conditional blocks without braces.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a coding style issue reported by checkpatch concerning
to usage of sizeof operand as a variable instead the type.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issue reported by checkpatch concerning to
an unnecessary line before close brace.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch concerning
to missing line after variable declarations.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts macros into inline functions since the usage of
second is encouraged by Coding Style instead of the first.
Macros converted to functions:
- dbg_status
- dbg_cmd
- dbg_port
- speed_char
The size after changes remains the same.
Before:
text data bss dec hex filename
36920 81 12 37013 9095 drivers/usb/host/ehci-hcd.o
After:
text data bss dec hex filename
36920 81 12 37013 9095 drivers/usb/host/ehci-hcd.o
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch concerning
to missing line after struct declarations.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch indents not empty functions to have the opening brace at the
beginning of the next line and body conforming coding style.
This also makes the function definition consistent with the file coding
style aligning parameters in sequential lines and indenting them with
two tabs.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces two snprintf() calls with scnprintf() in qh_lines()
and hence removes the unneeded sequential truncation tests.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch concerning
to missing spaces around operators.
There is an additional change on line 49 that removes unnecessary
parentheses around ternary operands.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch puts the closing parenthesis at the statement end removing
unnecessary "new line".
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch concerning
to switch case statements. There are few additional changes made to fix
other coding styles issues.
These additional changes are:
- The compound statement "({...})" on line 474 is pulled out from
snprintf parameters.
- On line 723 the constant "0x03" is moved to right.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch.
Coding style demands usage of C89-style comments and a specific format
when it's multiline.
This also removes the Free Software Foundation address because FSF can
change it again.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch. The only
change in this patch that isn't just removing spaces before opening
square brackets is at line 213 where the initialization of fls_strings[]
is placed in same line.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch. The vast
majority of changes in this patch are removing spaces before opening
parenthesis, but in some cases, a few additional changes are made to fix
other coding style issues.
These additional changes are:
- Spaces around >> on line 50.
- On line 55 a call to ehci_dbg reduced to a single line.
- sizeof operands surrounded with parenthesis on lines 877, 883, 889
and 901.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves the constant 0x3ff to right and put spaces
in the right shift.
Caught by coccinelle:
scripts/coccinelle/misc/compare_const_fl.cocci
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer operator must be sticked to name.
Caught by checkpatch:
ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes trailing semicolon from macros.
Caught by checkpatch:
"WARNING: macros should not use a trailing semicolon"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put space after comma.
This patch also changes QH_NEXT macro for better reading.
Caught by checkpatch: "ERROR: space required after that ','"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prefer to use __aligned(size) macro instead of
__attribute__((aligned(size))).
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use the 'do {} while (0)' wrapper in a single statement macro.
Caught by checkpatch: "WARNING: Single statement macros should not
use a do {} while (0) loop"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of space before open square bracket.
Caught by checkpatch: "ERROR: space prohibited before open square
bracket '['"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of space between function name and open parenthesis.
Caught by checkpatch: "WARNING: space prohibited between function name
and open parenthesis '('"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of spaces before comma.
Caught by checkpatch: "ERROR: space prohibited before that ','"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The index variable of list_for_each_entry_safe is an offset from a list
pointer, and thus should not be NULL.
Generated by: scripts/coccinelle/iterators/itnull.cocci
CC: Geliang Tang <geliangtang@163.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quting the relevant thread:
> In fact, I suspect the locking added by the kernel 3.13 commit for
> read_descriptors() is invalid because read_descriptors() performs no USB
> activity; read_descriptors() just reads information from an allocated
> memory structure. This structure is protected as the structure is
> existing before and after the sysfs vfs descriptors entry is created or
> destroyed.
You're right. For some reason I thought that usb_deauthorize_device()
would destroy the rawdescriptor structures (as mentioned in that
commit's Changelog), but it doesn't. The locking in read_descriptors()
is unnecessary.
> The information is only written at the time of enumeration
> and does not change. At least that is my understanding.
>
> It is noted that in our testing of kernel 3.8 on ARM, that sysfs
> read_descriptors() was non-blocking because the kernel 3.13 comment was
> not there.
>
> The pre-kernel 3.13 sysfs read_descriptors() seemed to work OK.
>
> Proposal:
> =========
>
> Remove the usb_lock_device(udev) and usb_unlock_device(udev) from
> devices/usb/core/sysfs.c in read_descriptors() that was added by the
> kernel 3.13 commit
> "232275a USB: fix substandard locking for the sysfs files"
>
> Any comments to this proposal ?
It seems okay to me. Please submit a patch.
So this removes the locking making the point about -EINTR in
the first path moot.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
232275a USB: fix substandard locking for the sysfs files
introduced needed locking into sysfs operations on USB devices
It, however, uses uninterruptible sleep and if the error
handling is on extreme cases of sleep lengths of 10s of seconds
are possible. Unless we are removing the device we should use
interruptible sleep.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB bus numbering is based on directly dealing with bitmaps and
defines a separate list of busses.
This can be simplified and unified by using existing idr functionality.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The speed field of the input slot context should represent the speed the
device is working at.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a xhci controller does not provide a protocol speed ID (PSI) table, a
default one should be used instead. Add the default values to the
SuperSpeedPlus device capability. Overwrite the default ones if a PSI table
exists. See xHCI 1.1 sectio 7.2.2.1.1 for more info
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases the devices with the speed set to USB_SPEED_SUPER_PLUS
are handled like regular SuperSpeed devices.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unlink_empty_async_suspended() is marked __maybe_unused. This is
because its caller, ehci_bus_suspend(), is protected by "#ifdef
CONFIG_PM". We should use the same protection here instead of
__maybe_unused.
unlink_empty_async_suspended() gets called only when the root hub is
suspended. It's silly for it to call start_iaa_cycle() at such a
time; the IAA mechanism doesn't work when the root hub isn't running.
It should call end_unlink_async() instead. But even this isn't
necessary, since there already is a call to end_iaa_cycle() right
before the call to unlink_empty_async_suspended(). All we have to do
is interchange the two subroutine calls.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Reutman reports that an AMD/ATI EHCI host controller on one of
his computers does not stop transferring data when an active bulk QH
is unlinked from the async schedule. Apparently that host controller
fails to implement the IAA mechanism correctly when an active QH is
unlinked. This leads to data corruption, because the controller
continues to update the QH in memory when the driver doesn't expect
it. As a result, the next URB submitted for that QH can hang, because
the link pointers for the TD queue have been messed up. This
misbehavior is observed quite regularly.
To be fair, the EHCI spec (section 4.8.2) says that active QHs should
not be unlinked. It goes on to recommend a procedure that involves
waiting for the QH to go inactive before unlinking it. In the real
world this is impractical, not least because the QH may _never_ go
inactive. (What were they thinking?) Sometimes we have no choice but
to unlink an active QH.
In an attempt to avoid the problems that can ensue, this patch changes
how the driver decides when the unlink is complete. In addition to
waiting through two IAA cycles, in cases where the QH was not known to
be inactive beforehand we now wait until a 2-ms period has elapsed
with the host controller making no change to the QH data structure
(the hw_current and hw_token fields in particular). The intuition
here is that after such a long period, the endpoint must be NAKing and
hopefully the QH has been dropped from the host controller's internal
cache. There's no way to know if this reasoning is really valid --
the spec is no help in this regard -- but at least this approach fixes
Michael's problem.
The test for whether the QH is already known to be inactive involves
the reason for unlinking the QH originally. If it was unlinked
because it had halted, or it stopped in response to a short read, or
it overlaid a dummy TD (a silicon bug), then it certainly is inactive.
If it was unlinked because the TD queue was empty and no TDs have been
added to the queue in the meantime, then it must be inactive. Or if
the hardware status indicates that the QH is currently halted (even if
that wasn't the reason for unlinking it), then it is inactive.
Otherwise, if none of those checks apply, we go through the 2-ms
delay.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Reutman <mreutman@epiqsolutions.com>
Tested-by: Michael Reutman <mreutman@epiqsolutions.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch improves the way ehci-hcd handles the iaa_in_progress flag.
The current code is somewhat careless in this regard:
The flag is meaningless when the root hub isn't running, most
particularly after the root hub has been suspended. But in
start_iaa_cycle(), the driver checks the flag before checking
the root hub's state. They should be checked in the opposite
order.
That routine also sets the flag too early, before it has
definitely committed to starting an IAA cycle.
The flag is turned off in end_unlink_async(). Upcoming
changes will call that routine at other times, not just at the
end of an IAA cycle. The two actions are logically separate
(although related), so we separate out a new routine to be
called in place of end_unlink_async() whenever an IAA cycle
ends: end_iaa_cycle().
iaa_in_progress should be turned off when the root hub is
suspended -- we certainly don't want it still to be set when
the root hub resumes. Therefore the call to
end_unlink_async() in ehci_bus_suspend() should also be
replaced with a call to end_iaa_cycle().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the "exception" bitflag in the ehci_qh structure
with a more explicit "unlink_reason" bitmask. This is for use in the
following patch, where we will need to have a good idea of the
reason for unlinking a QH, not just "something exceptional happened".
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Michael Reutman <mreutman@epiqsolutions.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes an issue found on Raspberry PI platform that prevents probe. Don't
skip setting the force mode if it's already set.
Fixes: 09c96980dc ("usb: dwc2: Add functions to set and clear force mode")
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit 263b7fb557 ("usb: dwc2: Move reset into
dwc2_get_hwparams()") due to regression found on bcm2835 platform. USB
ethernet fails, due to being unable to pick up proper parameters when
performing a plain reset before reading hw params.
Below shows the results of the gnptxfsiz and hptxfsiz with and before
and after reverting this (from Stefan Wahren):
So here is the probe result before Patch 1 is applied:
[ 1.283148] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host
[ 1.313894] dwc2 20980000.usb: gnptxfsiz=00201000
[ 1.314104] dwc2 20980000.usb: hptxfsiz=00000000
[ 1.353908] dwc2 20980000.usb: 256 invalid for host_nperio_tx_fifo_size. Check HW configuration.
[ 1.354262] dwc2 20980000.usb: 512 invalid for host_perio_tx_fifo_size. Check HW configuration.
[ 1.394249] dwc2 20980000.usb: DWC OTG Controller
[ 1.394561] dwc2 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.394917] dwc2 20980000.usb: irq 33, io mem 0x00000000
And here is the probe result after Patch 1 is applied:
[ 1.280107] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host
[ 1.353949] dwc2 20980000.usb: gnptxfsiz=01001000
[ 1.354166] dwc2 20980000.usb: hptxfsiz=02002000
[ 1.434301] dwc2 20980000.usb: DWC OTG Controller
[ 1.434616] dwc2 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.434973] dwc2 20980000.usb: irq 33, io mem 0x00000000
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The commit 7d32cdef53 ("usb: musb: fail with error when no DMA
controller set"), caused the core platform driver to correctly return an
error code when fail probing.
Unfurtante it also caused bug for a NULL pointer dereference, during
system suspend for the ux500 driver. The reason is a lacking validation
of the corresponding ->driver_data pointer, which won't be set when the
musb core driver fails to probe (or haven't yet been probed).
Fixes: 7d32cdef53 ("usb: musb: fail with error when no DMA...")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Initialize vbus_value to be 0 since it's possible not to assign
any value before judgement.
Acked-by: Peter Chen <peter.chen@nxp.com
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This driver registers for extcon events as part of its probe, but
never unregisters them in case of error in the probe path.
There were multiple issues noticed due to this missing error handling.
One of them is random crashes if the regulators are not ready yet by the
time probe is invoked.
Ivan's previous attempt [1] to fix this issue, did not really address
all the failure cases like regualtor/get_irq failures.
[1] https://lkml.org/lkml/2015/9/7/62
Without this patch the kernel would carsh with log:
...
Unable to handle kernel paging request at virtual address 17d78410
pgd = ffffffc001a5c000
[17d78410] *pgd=00000000b6806003, *pud=00000000b6806003, *pmd=0000000000000000
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u8:0 Not tainted 4.4.0+ #48
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
Workqueue: deferwq deferred_probe_work_func
task: ffffffc03686e900 ti: ffffffc0368b0000 task.ti: ffffffc0368b0000
PC is at raw_notifier_chain_register+0x1c/0x44
LR is at extcon_register_notifier+0x88/0xc8
pc : [<ffffffc0000da43c>] lr : [<ffffffc000606298>] pstate: 80000085
sp : ffffffc0368b3a70
x29: ffffffc0368b3a70 x28: ffffffc03680c310
x27: ffffffc035518000 x26: ffffffc035518000
x25: ffffffc03bfa20e0 x24: ffffffc035580a18
x23: 0000000000000000 x22: ffffffc035518458
x21: ffffffc0355e9a60 x20: ffffffc035518000
x19: 0000000000000000 x18: 0000000000000028
x17: 0000000000000003 x16: ffffffc0018153c8
x15: 0000000000000001 x14: ffffffc03686f0f8
x13: ffffffc03686f0f8 x12: 0000000000000003
x11: 0000000000000001 x10: 0000000000000001
x9 : ffffffc03686f0f8 x8 : 0000e3872014c1a1
x7 : 0000000000000028 x6 : 0000000000000000
x5 : 0000000000000001 x4 : 0000000000000000
x3 : 00000000354fb170 x2 : 0000000017d78400
x1 : ffffffc0355e9a60 x0 : ffffffc0354fb268
Fixes: 591fc116f3 ("usb: phy: msm: Use extcon framework for VBUS and ID detection")
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Expressions of the form "tty->termios.c_*flag & FLAG"
are more clearly expressed with the termios flags macros,
I_FLAG(), C_FLAG(), O_FLAG(), and L_FLAG().
Convert treewide.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are two fixes of crashes in the visor driver that could be
triggered using bad (malicious) descriptors, a fix for two memory leaks
in the new mxu11x0 driver, and an interface-blacklist fix for the option
driver.
Included are also some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=SxKT
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.5-rc2
Here are two fixes of crashes in the visor driver that could be
triggered using bad (malicious) descriptors, a fix for two memory leaks
in the new mxu11x0 driver, and an interface-blacklist fix for the option
driver.
Included are also some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
tty_init_termios() never returns an error; re-declare as void. Remove
unnecessary error handling from callers. Remove extern declarations
of tty_free_termios() and free_tty_struct() and re-declare in file
scope.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On nominal execution, private data allocated on port_probe and attach
are never freed. Add port_remove and release callbacks to free them
respectively.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Harald Linden reports that the ftdi_sio driver works properly for the
Yaesu SCU-18 cable if the device ids are added to the driver. So let's
add them.
Reported-by: Harald Linden <harald.linden@7183.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for two PIDs of LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The visor driver crashes in clie_5_attach() when a specially crafted USB
device without bulk-out endpoint is detected. This fix adds a check that
the device has proper configuration expected by the driver.
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Fixes: cfb8da8f69 ("USB: visor: fix initialisation of UX50/TH55 devices")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix null-pointer dereference at probe should a (malicious) Treo device
lack the expected endpoints.
Specifically, the Treo port-setup hack was dereferencing the bulk-in and
interrupt-in urbs without first making sure they had been allocated by
core.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Added the USB serial console device ID for IAI Corp. RCB-CV-USB
USB to RS485 adaptor.
Signed-off-by: Peter Dedecker <peter.dedecker@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In function usb_reset_and_verify_device, the old BOS descriptor may
still be used before allocating a new one. (usb_unlocked_disable_lpm
function uses it under the situation that it fails to disable lpm.)
So we cannot set the udev->bos to NULL before that, just keep what it
was. It will be overwrite when allocating a new one.
Crash log:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000010
IP: [<ffffffff8171f98d>] usb_enable_link_state+0x2d/0x2f0
Call Trace:
[<ffffffff8171ed5b>] ? usb_set_lpm_timeout+0x12b/0x140
[<ffffffff8171fcd1>] usb_enable_lpm+0x81/0xa0
[<ffffffff8171fdd8>] usb_disable_lpm+0xa8/0xc0
[<ffffffff8171fe1c>] usb_unlocked_disable_lpm+0x2c/0x50
[<ffffffff81723933>] usb_reset_and_verify_device+0xc3/0x710
[<ffffffff8172c4ed>] ? usb_sg_wait+0x13d/0x190
[<ffffffff81724743>] usb_reset_device+0x133/0x280
[<ffffffff8179ccd1>] usb_stor_port_reset+0x61/0x70
[<ffffffff8179cd68>] usb_stor_invoke_transport+0x88/0x520
Signed-off-by: Du, Changbin <changbin.du@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This phone needs to be handled by a specialised firmware tool
and is reported to crash irrevocably if cdc-acm takes it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Intel 7260 modem, it is needed for host side to send zero
packet if the BULK OUT size is equal to USB endpoint max packet
length. Otherwise, modem side may still wait for more data and
cannot give response to host side.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current acm driver, the bulk-in callback function ignores the
URBs unlinked in usb core.
This causes unexpected data loss in some cases. For example,
runtime suspend entry will unlinked all urbs and set urb->status
to -ENOENT even those urbs might have data not processed yet.
Hence, data loss occurs.
This patch lets bulk-in callback function handle unlinked urbs
to avoid data loss.
Signed-off-by: Tang Jian Qiang <jianqiang.tang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove a call to dev_err() that was reporting an unsuccesful call to
kmalloc(), as reporting memory allocation failures is redundant. Instead
of logging the error, clean up previously allocated resources and abort
the probe with -ENOMEM. Before this change sisusb->SiS_Pr could be
dereferenced even if null after failure of memory allocation.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove three calls to dev_err() from sisusb_probe() as
reporting memory allocation failures is redundant:
- Remove a call to dev_err() that was reporting unsuccesful call to
kzalloc().
- Remove two calls to dev_err() that were reporting unsuccesful calls
to kmalloc().
One call to dev_err() reporting memory allocation is left unchanged as
the last patch of the series removes it.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes null test before calls to kfree() as kfree() can
handle null pointers safely.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file drivers/usb/misc/sisusbvga/sisusb.c had 6 assignments inside if
tests. This patch move the assignment outside the test. The changes
also fix the remaining 2 lines that were over 80 characters.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file drivers/usb/misc/sisusbvga/sisusb.c contained coding style
issues reported by checkpatch. This patch fixes the following
errors:
- 12 WARNING: braces {} are not necessary for single statement blocks
- 04 ERROR: return is not a function, parentheses are not required
- 03 ERROR: do not initialise statics to 0
- 1 WARNING: else is not generally useful after a break or return
- 1 WARNING: braces {} are not necessary for any arm of this statement
- 1 WARNING: Block comments use * on subsequent lines
One case in which braces are not necessary is left unchanged as other
patch of the series will fix it.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes whitespace coding style issues that can't be fixed
without adding newlines. This patch fixes the following checkpatch
warnings:
- 20 ERROR: trailing statements should be on next line
- 15 WARNING: line over 80 characters
- 03 WARNING: Missing a blank line after declarations
- 01 ERROR: space required after that ','
Five lines over 80 characters are left. The first three wont change as
the fix would require split the cast and variable name in different
lines which makes the code less readable. The last two will be fixed by
other patch in the series.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes whitespace coding style issues that can be fixed
within a single line. This patch fixes the following checkpatch
warnings:
- 83 ERROR: space required after that ','
- 13 ERROR: switch and case should be at the same indent
- 08 WARNING: please, no spaces at the start of a line
- 03 ERROR: space required before the open parenthesis '('
- 04 WARNING: suspect code indent for conditional statements
- 01 WARNING: space prohibited between function name and open parenthesis
- 01 ERROR: spaces required around that '='
- 01 ERROR: code indent should use tabs where possible
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use bus_to_hcd() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use to_usb_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices send response IUs when you'd expect a sense IU.
As a response to a wrong LUN that is within spec.
We cannot get away without handling for response IUs.
This version fixes the issues Hans raised.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry() instead of list_for_each() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry() instead of list_for_each() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry*() instead of list_for_each*() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver calls pci_set_mwi to enable memory-write-invalidate when it
is initialized, but does not call pci_clear_mwi when it is removed. Many
other drivers calls pci_clear_mwi when pci_set_mwi is called, such as
r8169, 8139cp and e1000.
This patch adds a function "ehci_pci_remove" to remove the pci driver.
This function calls pci_clear_mwi and usb_hcd_pci_remove, which can
fix the problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver calls ehci_mem_init to allocate memory resources.
But these resources are not freed when ehci_halt fails.
This patch adds "ehci_mem_cleanup" in error handling code to fix this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registering usb_hcd_platform_shutdown to be called during
shutdown. This is a generic function that performs the
generic host stack's shutdown. It ensures that USB
operations do not continue while kexec boots a new kernel.
Signed-off-by: Azriel Samson <asamson@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default value for the 'transceiver select' field of
the PORTSC register may not always be correct. Previously
the phy-msm-usb driver would do this for us, but since
ehci-msm can now be instantiated standalone without any PHY
driver, the register needs to be explicitly initialized to
ULPI mode to properly communicate with the PHY.
This is not readily apparent, as firmware or bootloader code
also happen to pre-initialize this for us. However, it can
manifest when performing a driver unbind/rebind as follows:
cd /sys/bus/platform/drivers/msm_hsusb_host
echo QCOM8040:00 > unbind
echo QCOM8040:00 > bind
The EHCI core executes a controller reset as part of this,
and as a result the register in question would revert to
its default state and must be re-initialized properly.
Furthermore this may be useful in the future when adding
PM suspend/resume support.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow the EHCI MSM driver to probe against an ACPI enumerated
device with ID QCOM8040.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the EHCI MSM driver has a hard dependency to be created
by an OTG layer, namely the phy-msm-usb driver. In some cases or
board configurations we want to allow the EHCI host to be
instantiated without OTG capability. Instead, relax the dependency
on having an OTG PHY being present and call usb_add_hcd() directly.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable the silicon quirk which is normally enabled for HSIC
host mode. This would otherwise prevent low speed devices
from enumerating properly.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This splits one big probing function into two smaller ones. The main one
is now responsible for the generic stuff: allocating memory & enabling
power using GPIO. The new one contains code that is specific to the USB
2.0 bcma core.
This will allow adding support for the USB 3.0 bcma core (handling XHCI)
in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having "bool ohci" argument in bcma_hcd_create_pdev function limited it
to support two cases only (OHCI and EHCI) and put too much logic in it.
Lets make caller pass all required data. This adds few extra arguments
to the function call but will allow us to reuse this code and handle
more cases in the future (e.g. add XHCI support).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbasename() helper is dedicated to find a last part of the filename or
pathname. USB core uses open-coded variant of that helper.
Replace some lines of code by kbasename() call.
The current users do not have trailing slash and we are on the safe side to
make such change. I dig a history of the code under question up and found the
patch [1] that brought it along with the same to tty layer. The check for
trailing slash looks like copy'n'paste thing and I consider it as redundant.
[1] http://www.kernel.org/pub/linux/kernel//people/akpm/patches/2.5/2.5.69/2.5.69-mm3/broken-out/linus.patch
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change Power architecture specific APIs such as in_be32/out_be32
for registers read/write. Instead using ioread/writebe32 which are
defined for power as well as arm architecture
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Sriram Dash <sriram.dash@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb 3.1 extend the hub get-port-status request by adding different
request types. the new request types return 4 additional bytes called
extended port status, these bytes are returned after the regular
portstatus and portchange values.
The extended port status contains a speed ID for the currently used
sublink speed. A table of supported Speed IDs with details about the link
is provided by the hub in the device descriptor BOS SuperSpeedPlus
device capability Sublink Speed Attributes.
Support this new request. Ask for the extended port status after port
reset if hub supports USB 3.1. If link is running at SuperSpeedPlus
set the device speed to USB_SPEED_SUPER_PLUS
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same way as SuperSpeed devices show "5000" as device speed we wan't to
show "10000" as the default speed for SuperSpeedPlus devices in sysfs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A hcd roothub that supports HCD_USB31 is running at SuperSpeedPlus speed
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new USB_SPEED_SUPER_PLUS device speed, and make sure usb core can
handle the new speed.
In most cases the behaviour is the same as with USB_SPEED_SUPER SuperSpeed
devices. In a few places we add a "Plus" string to inform the user of the
new speed.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing coccicheck warning which recommends to use memdup_user instead
to reimplement its code, using memdup_user simplifies the code
./drivers/usb/core/devio.c:1398:11-18: WARNING opportunity for memdup_user
Signed-off-by: Rahul Pathak <rpathak@visteon.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed an unnecessary space between a function name and arguments.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbhs_pkt_handle structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove mach/irq.h from the list of included headers, there is no
compilation dependency on this include file, the change is needed
to prevent a compilation failure, when mach/irq.h is removed.
Additionally remove other unneeded includes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull final vfs updates from Al Viro:
- The ->i_mutex wrappers (with small prereq in lustre)
- a fix for too early freeing of symlink bodies on shmem (they need to
be RCU-delayed) (-stable fodder)
- followup to dedupe stuff merged this cycle
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: abort dedupe loop if fatal signals are pending
make sure that freeing shmem fast symlinks is RCU-delayed
wrappers for ->i_mutex access
lustre: remove unused declaration
Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in arm-soc
a bit late, which is why we've kept it separate from the other updates
and are sending it separately here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LG3u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC support for Tegra platforms from Olof Johansson:
"Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in
arm-soc a bit late, which is why we've kept it separate from the other
updates and are sending it separately here"
* tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support
arm64: tegra: Add NVIDIA P2597 I/O board support
arm64: tegra: Add NVIDIA Jetson TX1 support
arm64: tegra: Add NVIDIA P2571 board support
arm64: tegra: Add NVIDIA P2371 board support
arm64: tegra: Add NVIDIA P2595 I/O board support
arm64: tegra: Add NVIDIA P2530 main board support
arm64: tegra: Add Tegra210 support
arm64: tegra: Add NVIDIA Tegra132 Norrin support
arm64: tegra: Add Tegra132 support
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).
Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on
top of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates
of the ACPICA's copyright notices, a code fixup resulting from
a regression fix that was necessary in the upstream code only
(the regression fixed by it has never been present in Linux)
and a compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke
it on practically all architectures other than x86 and make a
couple of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether
or not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on
the problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up
a bit and update the MAINTAINERS information related to it
(Chanwoo Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=bKJ9
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"This includes fixes on top of the previous batch of PM+ACPI updates
and some new material as well.
From the new material perspective the most significant are the driver
core changes that should allow USB devices to stay suspended over
system suspend/resume cycles if they have been runtime-suspended
already beforehand. Apart from that, ACPICA is updated to upstream
revision 20160108 (cosmetic mostly, but including one fixup on top of
the previous ACPICA update) and there are some devfreq updates the
didn't make it before (due to timing).
A few recent regressions are fixed, most importantly in the cpuidle
menu governor and in the ACPI backlight driver and some x86 platform
drivers depending on it.
Some more bugs are fixed and cleanups are made on top of that.
Specifics:
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on top
of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates of
the ACPICA's copyright notices, a code fixup resulting from a
regression fix that was necessary in the upstream code only (the
regression fixed by it has never been present in Linux) and a
compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke it
on practically all architectures other than x86 and make a couple
of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether or
not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on the
problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up a
bit and update the MAINTAINERS information related to it (Chanwoo
Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas
Prabhu)"
* tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
cpuidle: menu: Avoid pointless checks in menu_select()
sched / idle: Drop default_idle_call() fallback from call_cpuidle()
cpupower: Fix build error in cpufreq-info
cpuidle: Don't enable all governors by default
cpuidle: Default to ladder governor on ticking systems
time: nohz: Expose tick_nohz_enabled
ACPICA: Update version to 20160108
ACPICA: Silence a -Wbad-function-cast warning when acpi_uintptr_t is 'uintptr_t'
ACPICA: Additional 2016 copyright changes
ACPICA: Reduce regression fix divergence from upstream ACPICA
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Satellite R830
ACPI / video: Revert "thinkpad_acpi: Use acpi_video_handles_brightness_key_presses()"
ACPI / video: Document acpi_video_handles_brightness_key_presses() a bit
ACPI / video: Fix using an uninitialized mutex / list_head in acpi_video_handles_brightness_key_presses()
ACPI / video: Revert "ACPI / video: driver must be registered before checking for keypresses"
ACPI / fan: Improve acpi_device_update_power error message
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Portege R700
cpuidle: menu: Fix menu_select() for CPUIDLE_DRIVER_STATE_START == 0
MAINTAINERS: Add devfreq-event entry
MAINTAINERS: Add missing git repository and directory for devfreq
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Introduce configfs support for unlocked configfs_depend_item()
(krzysztof + andrezej)
- Conversion of usb-gadget target driver to new function registration
interface (andrzej + sebastian)
- Enable qla2xxx FC target mode support for Extended Logins (himansu +
giridhar)
- Enable qla2xxx FC target mode support for Exchange Offload (himansu +
giridhar)
- Add qla2xxx FC target mode irq affinity notification + selective
command queuing. (quinn + himanshu)
- Fix iscsi-target deadlock in se_node_acl configfs deletion (sagi +
nab)
- Convert se_node_acl configfs deletion + se_node_acl->queue_depth to
proper se_session->sess_kref + target_get_session() usage. (hch +
sagi + nab)
- Fix long-standing race between se_node_acl->acl_kref get and
get_initiator_node_acl() lookup. (hch + nab)
- Fix target/user block-size handling, and make sure netlink reaches
all network namespaces (sheng + andy)
Note there is an outstanding bug-fix series for remote I_T nexus port
TMR LUN_RESET has been posted and still being tested, and will likely
become post -rc1 material at this point"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (56 commits)
scsi: qla2xxxx: avoid type mismatch in comparison
target/user: Make sure netlink would reach all network namespaces
target: Obtain se_node_acl->acl_kref during get_initiator_node_acl
target: Convert ACL change queue_depth se_session reference usage
iscsi-target: Fix potential dead-lock during node acl delete
ib_srpt: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Wait for command completion before freeing a session
target: Fix a memory leak in target_dev_lba_map_store()
target: Support aborting tasks with a 64-bit tag
usb/gadget: Remove set-but-not-used variables
target: Remove an unused variable
target: Fix indentation in target_core_configfs.c
target/user: Allow user to set block size before enabling device
iser-target: Fix non negative ERR_PTR isert_device_get usage
target/fcoe: Add tag support to tcm_fc
qla2xxx: Check for online flag instead of active reset when transmitting responses
qla2xxx: Set all queues to 4k
qla2xxx: Disable ZIO at start time.
qla2xxx: Move atioq to a different lock to reduce lock contention
...
* pm-core:
driver core: Avoid NULL pointer dereferences in device_is_bound()
platform: Do not detach from PM domains on shutdown
USB / PM: Allow USB devices to remain runtime-suspended when sleeping
PM / sleep: Go direct_complete if driver has no callbacks
PM / Domains: add setter for dev.pm_domain
device core: add device_is_bound()
Pull kbuild updates from Michal Marek:
- Make <modname>-m in makefiles work like <modname>-y and fix the
fallout
- Minor genksyms fix
- Fix race with make -j install modules_install
- Move -Wsign-compare from make W=1 to W=2
- Other minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Demote 'sign-compare' warning to W=2
Makefile: revert "Makefile: Document ability to make file.lst and file.S" partially
kbuild: Do not run modules_install and install in paralel
genksyms: Handle string literals with spaces in reference files
fixdep: constify strrcmp arguments
ath10k: Fix build with CONFIG_THERMAL=m
Revert "drm: Hack around CONFIG_AGP=m build failures"
kbuild: Allow to specify composite modules with modname-m
staging/ad7606: Actually build the interface modules
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
Here is the big USB drivers update for 4.5-rc1. Lots of gadget driver
updates and fixes, like usual, and a mix of other USB driver updates as
well. Full details in the shortlog. All of these have been in
linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlaV2rUACgkQMUfUDdst+ym2XQCgqdDOlyGX5B//9CZ2kH1DrDW9
qLsAoLSBvw4hk+Aotv6tn8AayMpHwqV1
=pFLC
-----END PGP SIGNATURE-----
Merge tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB drivers update for 4.5-rc1.
Lots of gadget driver updates and fixes, like usual, and a mix of
other USB driver updates as well. Full details in the shortlog. All
of these have been in linux-next for a while"
* tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (191 commits)
MAINTAINERS: change my email address
USB: usbmon: remove assignment from IS_ERR argument
USB: mxu11x0: drop redundant function name from error messages
USB: mxu11x0: fix debug-message typos
USB: mxu11x0: rename usb-serial driver
USB: mxu11x0: fix modem-control handling on B0-transitions
USB: mxu11x0: fix memory leak on firmware download
USB: mxu11x0: fix memory leak in port-probe error path
USB: serial: add Moxa UPORT 11x0 driver
USB: cp210x: add ID for ELV Marble Sound Board 1
usb: chipidea: otg: use usb autosuspend to suspend bus for HNP
usb: chipidea: host: set host to be null after hcd is freed
usb: chipidea: removing of_find_property
usb: chipidea: implement platform shutdown callback
usb: chipidea: clean up CONFIG_USB_CHIPIDEA_DEBUG reference
usb: chipidea: delete static debug support
usb: chipidea: support debugfs without CONFIG_USB_CHIPIDEA_DEBUG
usb: chipidea: udc: improve error handling on _hardware_enqueue
usb: chipidea: udc: _ep_queue and _hw_queue cleanup
usb: dwc3: of-simple: fix build warning on !PM
...
Pull misc vfs updates from Al Viro:
"All kinds of stuff. That probably should've been 5 or 6 separate
branches, but by the time I'd realized how large and mixed that bag
had become it had been too close to -final to play with rebasing.
Some fs/namei.c cleanups there, memdup_user_nul() introduction and
switching open-coded instances, burying long-dead code, whack-a-mole
of various kinds, several new helpers for ->llseek(), assorted
cleanups and fixes from various people, etc.
One piece probably deserves special mention - Neil's
lookup_one_len_unlocked(). Similar to lookup_one_len(), but gets
called without ->i_mutex and tries to avoid ever taking it. That, of
course, means that it's not useful for any directory modifications,
but things like getting inode attributes in nfds readdirplus are fine
with that. I really should've asked for moratorium on lookup-related
changes this cycle, but since I hadn't done that early enough... I
*am* asking for that for the coming cycle, though - I'm going to try
and get conversion of i_mutex to rwsem with ->lookup() done under lock
taken shared.
There will be a patch closer to the end of the window, along the lines
of the one Linus had posted last May - mechanical conversion of
->i_mutex accesses to inode_lock()/inode_unlock()/inode_trylock()/
inode_is_locked()/inode_lock_nested(). To quote Linus back then:
-----
| This is an automated patch using
|
| sed 's/mutex_lock(&\(.*\)->i_mutex)/inode_lock(\1)/'
| sed 's/mutex_unlock(&\(.*\)->i_mutex)/inode_unlock(\1)/'
| sed 's/mutex_lock_nested(&\(.*\)->i_mutex,[ ]*I_MUTEX_\([A-Z0-9_]*\))/inode_lock_nested(\1, I_MUTEX_\2)/'
| sed 's/mutex_is_locked(&\(.*\)->i_mutex)/inode_is_locked(\1)/'
| sed 's/mutex_trylock(&\(.*\)->i_mutex)/inode_trylock(\1)/'
|
| with a very few manual fixups
-----
I'm going to send that once the ->i_mutex-affecting stuff in -next
gets mostly merged (or when Linus says he's about to stop taking
merges)"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
nfsd: don't hold i_mutex over userspace upcalls
fs:affs:Replace time_t with time64_t
fs/9p: use fscache mutex rather than spinlock
proc: add a reschedule point in proc_readfd_common()
logfs: constify logfs_block_ops structures
fcntl: allow to set O_DIRECT flag on pipe
fs: __generic_file_splice_read retry lookup on AOP_TRUNCATED_PAGE
fs: xattr: Use kvfree()
[s390] page_to_phys() always returns a multiple of PAGE_SIZE
nbd: use ->compat_ioctl()
fs: use block_device name vsprintf helper
lib/vsprintf: add %*pg format specifier
fs: use gendisk->disk_name where possible
poll: plug an unused argument to do_poll
amdkfd: don't open-code memdup_user()
cdrom: don't open-code memdup_user()
rsxx: don't open-code memdup_user()
mtip32xx: don't open-code memdup_user()
[um] mconsole: don't open-code memdup_user_nul()
[um] hostaudio: don't open-code memdup_user()
...
The big thing here is Tegra210 support, which is really only the Kconfig
symbol. Other than that there's a few miscellaneous fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zr7c
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.5-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into late/tegra
ARM: tegra: Core SoC changes for v4.5-rc1
The big thing here is Tegra210 support, which is really only the Kconfig
symbol. Other than that there's a few miscellaneous fixes.
* tag 'tegra-for-4.5-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
Signed-off-by: Olof Johansson <olof@lixom.net>
* patchwork: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
Have dev_pm_ops.prepare return 1 for USB devices and ports so that USB
devices can remain runtime-suspended when the system goes to a sleep
state, if their wakeup state is correct and they have runtime PM enabled.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Avoid that building with W=1 triggers compiler warnings about
set-but-not-used variables.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here's another device id for cp210x.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jeCr
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for v4.4-rc8
Here's another device id for cp210x.
Signed-off-by: Johan Hovold <johan@kernel.org>
These updates add support for Moxa UPort 1100-series devices through a
new mxu11x0 driver.
The cp210x driver gains proper support for cp2108 devices by working
around a couple of firmware bugs, and generic wait-until-sent support
(e.g. for tcdrain) is also added.
Included are also some general clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=tyK5
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.5-rc1
These updates add support for Moxa UPort 1100-series devices through a
new mxu11x0 driver.
The cp210x driver gains proper support for cp2108 devices by working
around a couple of firmware bugs, and generic wait-until-sent support
(e.g. for tcdrain) is also added.
Included are also some general clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant function name from a few error messages.
Drop redundant error message when generic open fails.
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to release the private data before returning -ENODEV after
having downloaded the firmware during first probe.
Clean up the error paths while at it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix memory leak in port-probe error path by verifying the interrupt-in
urb before allocating the private data.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a driver which supports :
- UPort 1110 : 1 port RS-232 USB to Serial Hub.
- UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
- UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
- UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
- UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
This driver is based on GPL MOXA driver written by Hen Huang and available
on MOXA website. The original driver was based on io_ti serial driver.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add the USB device ID for ELV Marble Sound Board 1.
Signed-off-by: Oliver Freyermuth <o.freyermuth@googlemail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
- Delete static debug for chipidea driver.
- Suspend USB core when A device tries to switch to peripheral mode,
at former design, it just stopped SoF simply but USB core doesn't know it.
- Several small changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWfLjWAAoJEEhZKYFQ1nG7R/cH/3xP4nz3pDDOpsX6U8Q1V81D
K7118WeAOx64sdGRZ3bsEjNko4NI1j2jcQU2Zgtx/I5Q0lJfNm4linNNWJHKEb/m
1VJVxFJXP6lwWImVWNJbyvhzel8mlgaNza+ZabUOAFmSig9q3yHUq5lDqzPVLZWY
z7lYQS+sOsCorsQierXiRxSRvkipB32NpdfhEXkj6P6Ji2a1UDDRA7F3f9k9t8QR
iI1T5+gbJL/3eo+ToOdlGciIUjoa4bK5b0Iz+QeU2eSOqjuVcu4tZO5IJbH/o10Z
dAhcDOr0DPEGzfpwihevyX3HcRKTKHPlzo2GdW5TJ5e7vm5C43fGHB0GgpIJBWw=
=7ZBY
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-testing
Peter writes:
The chipidea changes for v4.5-rc1
- Delete static debug for chipidea driver.
- Suspend USB core when A device tries to switch to peripheral mode,
at former design, it just stopped SoF simply but USB core doesn't know it.
- Several small changes.
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8vM4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.5
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
Directly manipulate the controller regsiter to suspend the usb bus
for HNP is not the proper way, this should be done through the usbcore
by usb autosuspend. So to start HNP, autosuspend support should be
added for OTG devices interface driver if it's not enabled.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Set ci->hcd and ci->otg.host to be null in host_stop since the
hcd already freed.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
call to of_find_property() before of_property_read_u32() is unnecessary.
of_property_read_u32() anyway calls to of_find_property() only.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
disable wakeup irq during shutdown, otherwise kexec fails for
kernels that setup irq handlers before resetting the hardware
Signed-off-by: Andreas Fenkart <andreas.fenkart@dev.digitalstrom.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Since this configuration option has deleted, cleans up all
its references.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Since we need to mount debugfs to show/store the things we
want to debug, it is duplicated to add another configuration
to enable it. Meanwhile, with CONFIG_USB_CHIPIDEA_DEBUG,
we can't support chipidea debugfs at runtime.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: Jun Li <jun.li@freescale.com>
_hardware_enqueue() didn't check for errors when using
add_td_to_list() which can fail if dma_pool_alloc fails, thus
causing a kernel panic when lastnode->ptr is NULL.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Update comments to reflect current state of functions.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
if we have a !PM kernel build, our runtime
suspend/resume callbacks will be left defined but
unused. Add a ifdef CONFIG_PM guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the request->length is zero, a ZLP should already be sent due to that
and another ZLP is not needed to terminate the transfer.
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
R-Car H3 has USB3.0 peripheral controllers. This controller's has the
following features:
- Supports super, high and full speed
- Contains 30 pipes for bulk or interrupt transfer
- Contains dedicated DMA controller
This driver doesn't support the dedicated DMAC for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In specific conditions (involving usb hubs) dwc2 devices can create a
lot of interrupts, even to the point of overwhelming devices running
at low frequencies. Some devices need to do special clock handling
at shutdown-time which may bring the system clock below the threshold
of being able to handle the dwc2 interrupts. Disabling dwc2-irqs
in a shutdown callbacks prevents reboots/poweroffs from getting stuck
in such cases.
The hsotg struct already contains an unused irq element, so we can
just use it to store the irq number for the shutdown callback.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The phy's init routine must be called before it can be used. Do so in
musb_init_controller and the matching shutdown in musb_remove.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The "enumspd" field is located in register DSTS[2:1], but the code
which checks the bitfield does not shift the value accordingly. This
in turn causes incorrect detection of gadget link partner speed in
dwc2_hsotg_irq_enumdone() .
Shift the value accordingly to fix the problem with speed detection.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove call to dwc2_hsotg_init() from dwc2_gadget_init(). The
gadget_init function should not access any device registers because the
mode isn't guaranteed here.
Also, this is already called elsewhere before anything starts on the
gadget so it is not necessary here.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reset already happens before this so just force the dr_mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The delay for force mode is only 25ms according to the databook.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2_core_reset() function exists in the core so use that one
instead.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the previously cached hw params in the gadget. This saves a reset
and force mode in the gadget initialization during probe and makes
getting the hardware parameters consistent between gadget and host.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds separate functions to get the host and device specific hardware
parameters. The functions check whether the parameters need to be read
at all, depending on dr_mode, and forces the mode only if necessary.
This saves some delays during probe. This also adds two device mode
parameters that will be used by the gadget.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added functions to set force mode for host and device. These functions
will check the current mode and only force if needed thus avoiding
unnecessary force mode delays. However clearing the mode is currently
done unconditionally and with the delay in place. This is needed during
the connector ID status change interrupt in order to ensure that the
mode has changed properly. This preserves the old behavior only for this
case. The warning comment about this is moved into the clear mode
condition.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The reset is required to get reset values of the hardware parameters but
the force mode is not. Move the base reset into dwc2_get_hwparams() and
do the reset and force mode afterwards.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These functions should go in core.h where they can be called from core,
device, or host.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dr_mode parameter was being checked against how the dwc2 module
was being configured at compile time. But it wasn't checked against
the hardware capabilities, nor were the hardware capabilities checked
against the compilation parameters.
This commit adds those checks and adjusts dr_mode to an appropriate
value, if needed. If the hardware capabilities and module compilation
do not match then we fail as it wouldn't be possible to run properly.
The hardware, module, and dr_mode, can each be set to host, device,
or otg. Check that all these values are compatible and adjust the
value of dr_mode if possible.
The following table summarizes the behavior:
actual
HW MOD dr_mode dr_mode
------------------------------
HST HST any : HST
HST DEV any : ---
HST OTG any : HST
DEV HST any : ---
DEV DEV any : DEV
DEV OTG any : DEV
OTG HST any : HST
OTG DEV any : DEV
OTG OTG any : dr_mode
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added functions to query the GHWCFG2.OTG_MODE. This tells us whether the
controller hardware is configured for OTG, device-only, or host-only.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc2_core_reset() was previously renamed to
dwc2_core_reset_and_dr_force_mode(). Now add back dwc2_core_reset() which
performs only a basic core reset without forcing the mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Renamed dwc2_core_reset() to dwc2_core_reset_and_force_dr_mode(). This
describes what it is doing more accurately. This is in preparation of
introducing a plain dwc2_core_reset() function that only performs the
reset and doesn't force the mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the databook, the core soft reset should be done before
checking for AHBIDLE. The gadget version of core reset had it correct
but the hcd version did not. This fixes the hcd version.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Calls to dwc2_core_reset() are currently very slow, taking at least
150ms (possibly more). It behooves us to take as many of these calls
out as possible.
It turns out that the calls in dwc2_fs_phy_init() and dwc2_hs_phy_init()
should (as documented in the code) only be needed if we need to do a PHY
SELECT. That means that if we see that we can avoid the PHY SELECT then
we can avoid the reset.
This patch appears to successfully bypass two resets (one per USB
device) on rk3288-based ARM Chromebooks.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I found that the probe function of dwc2 driver takes much time
when kernel boot up. There are many long delays in the probe
function these take almost 1 second.
This patch trying to reduce unnecessary delay time.
In dwc2_core_reset() I see it use two at least 20ms delays to
wait AHB idle and core soft reset, but dwc2 data book said that
dwc2 core soft reset and AHB idle just need a few clocks (I think
it refers to AHB clock, and AHB clock run at 150MHz in my RK3288
board), so 20ms is too long, delay 1us for wait AHB idle and soft
reset is enough.
And in dwc2_get_hwparams() it takes 150ms to wait ForceHostMode
and ForceDeviceMode valid but in data book it said software must
wait at least 25ms before the change to take effect, so I reduce
this time to 25ms~50ms. By the way, is there any state bit show
that the force mode take effect ? Could we poll curmod bit for
figuring out if the change take effect ?
It seems that usleep_range() at boot time will pick the longest
value in the range. In dwc2_core_reset() there is a very long
delay takes 200ms, and this function run twice when probe, could
any one tell me is this delay time resonable ?
I have tried this patch in my RK3288-evb board. It works well.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On some host-only DWC2 ports (like the one in rk3288) when we set
GUSBCFG_FORCEHOSTMODE in GUSBCFG and then read back, we don't see the
bit set. Presumably that's because the port is always forced to HOST
mode so there's no reason to implement these status bits.
Since we know dwc2_core_reset() is always called before
dwc2_get_hwparams() and we know dwc2_core_reset() should have set
GUSBCFG_FORCEHOSTMODE whenever hsotg->dr_mode == USB_DR_MODE_HOST, we
can just check hsotg->dr_mode to decide that we can skip the delays in
dwc2_get_hwparams().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In (usb: dwc2: reset dwc2 core before dwc2_get_hwparams()) we added an
extra reset to the probe path for the dwc2 USB controllers. This
allowed proper detection of parameters even if the firmware had already
used the USB part.
Unfortunately, this extra reset is quite slow and is affecting boot
speed. We can avoid the double-reset by skipping the extra reset that
would happen just after the one we added. Logic that explains why this
is safe:
* As of the CL mentioned above, we now always call dwc2_core_reset() in
dwc2_driver_probe() before dwc2_hcd_init().
* The only caller of dwc2_hcd_init() is dwc2_driver_probe(), so we're
guaranteed that dwc2_core_reset() was called before dwc2_hdc_init().
* dwc2_hdc_init() is the only caller that passes an irq other than -1 to
dwc2_core_init(). Thus if dwc2_core_init() is called with an irq
other than -1 we're guaranteed that dwc2_core_reset was called before
dwc2_core_init().
...this allows us to remove the dwc2_core_reset() in dwc2_core_init() if
irq is not < 0.
Note that since "irq" wasn't used in the function dwc2_core_init()
anyway and since select_phy was always set at exactly the same times we
could avoid the reset, we remove "irq" and rename "select_phy" to
"initial_setup" and adjust the callers accordingly.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We initiate dwc2 usb controller in BIOS, dwc2_core_reset() should
be called before dwc2_get_hwparams() to reset core registers to
default value. Without this the FIFO setting might be incorrect
because calculating FIFO size need power-on value of
GRXFSIZ/GNPTXFSIZ/HPTXFSIZ registers.
This patch could avoid warnning massage like in rk3288 platform:
[ 2.074764] dwc2 ff580000.usb: 256 invalid for
host_perio_tx_fifo_size. Check HW configuration.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Previously dwc2_get_hwparams() was changing GUSBCFG and not putting it
back the way it was (specifically it set and cleared FORCEHOSTMODE).
Since we want to move dwc2_core_reset() _before_ dwc2_get_hwparams() we
should make sure dwc2_get_hwparams() isn't messing with things in a
permanent way.
Since we're now looking at GUSBCFG, it's obvious that we shouldn't need
all the extra delays if FORCEHOSTMODE was already set. This will avoid
some delays for any ports that have forced host mode.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When receiving GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF interrupt,
DCTL will be overwritten with DCTL_CGOUTNAK or DCTL_CGNPINNAK values.
Instead of overwriting it, write only needed bits.
It could cause an issue if GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF
interrupt is received after dwc2 disabled pullup by writing
DCTL_SFTDISCON bit.
Pullup will then be re-enabled whereas it should not.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To stop an out endpoint, software should set sets the Global OUT NAK,
but not the Global Non-periodic IN NAK. This driver bug leads the out-ep
failed be in disabled state with below error.
dwc2_hsotg_ep_stop_xfr: timeout DOEPCTL.EPDisable
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It dose not work when we want to use the usb-to-serial port based
on one usb gadget as a console. Thus this patch adds the console
initialization to support this request.
To avoid the re-entrance when transferring data with usb endpoint,
it introduces a kthread to do the IO transmission.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We want the USB and PHY fixes in here as well to make things easier for
testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow using the tcm function as a component of a gadget composed with
ConfigFS.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Do not directly use file static strings definitions in instances of f_tcm.
Instead use usb_gstrings_attach.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The only instance is guaranteed with TPG_INSTANCES defined to 1.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There are no old function interface users left.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Convert the only user of old tcm function interface so that the old
interface can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Converting tcm to the new function interface requires converting
USB tcm's function code and its users.
This patch converts the f_tcm.c to the new function interface.
The file can be now compiled into a separate module usb_f_tcm.ko.
The old function interface is provided by means of preprocessor conditional
directives. After all users are converted, the old interface can be
removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Prepare for converting tcm to new function registration interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify function code.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify the function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Prepare for splitting tcm_usb_gadget into legacy gadget proper and f_tcm.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Prepare for factoring out f_tcm from a legacy gadget.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix up tcm_usbg_tpg_store_enable() return value to propagate
usbg_attach() failure up to user-space if no HDC is found.
Reported-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing tcm_usbg_drop_nexus() to properly
release tcm_usbg_nexus memory during typical ->fabric_drop_tpg()
callback shutdown.
Reported-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Avoid stripping off the 'naa.' I_T nexus prefix from configfs
attribute store input, so that user-space will get back what
it originaly wrote into ../usb_gadget/$WWPN/$TPGT/nexus.
Note the SCSI initiator WWPN is purely symbolic for UAS + BOT,
so it will not effect host side code.
Reported-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Commit 8520f38099 ("USB: change hub initialization sleeps to
delayed_work") changed the hub_activate() routine to make part of it
run in a workqueue. However, the commit failed to take a reference to
the usb_hub structure or to lock the hub interface while doing so. As
a result, if a hub is plugged in and quickly unplugged before the work
routine can run, the routine will try to access memory that has been
deallocated. Or, if the hub is unplugged while the routine is
running, the memory may be deallocated while it is in active use.
This patch fixes the problem by taking a reference to the usb_hub at
the start of hub_activate() and releasing it at the end (when the work
is finished), and by locking the hub interface while the work routine
is running. It also adds a check at the start of the routine to see
if the hub has already been disconnected, in which nothing should be
done.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Alexandru Cornea <alexandru.cornea@intel.com>
Tested-by: Alexandru Cornea <alexandru.cornea@intel.com>
Fixes: 8520f38099 ("USB: change hub initialization sleeps to delayed_work")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code expects the loop to end with "retries" set to zero but, because
it is a post-op, it will end set to -1. I have fixed this by moving the
decrement inside the loop.
Fixes: 014aa2a3c3 ('USB: ipaq: minor ipaq_open() cleanup.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix bad unlock balance: ep0_write enter with the locks locked from
inode.c:1769, hence it must exit with spinlock held to avoid double
unlock in dev_config.
Signed-off-by: David Eccher <d.eccher@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add fallback compatibility strings for R-Car Gen2 and Gen3.
This is in keeping with the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The gadget ethernet driver supports changing the MTU, but only allows this
when the USB cable is removed. The comment indicates that this is because
the "peer won't know". Even if the network link is still down and only the
USB link is established, the driver won't allow the change.
Other network interfaces allow changing the MTU any time, and don't force
the link to be disabled. This makes perfect sense, because in order to be
able to negotiate the MTU, the link needs to be up.
Remove the restriction so that it is now actually possible to change the
MTU (e.g. using "ifconfig usb0 mtu 15000") without having to manually pull
the plug or change the driver's default setting.
This is especially important after commit bba787a860
("usb: gadget: ether: Allow jumbo frames")
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces pre-allocation of IN endpoint USB requests. This
improves on latency (requires no usb request allocation on transmit) and avoid
several potential probles on allocating too many usb requests (which involves
DMA pool allocation problems).
This implementation also handles better multiple MIDI Gadget ports, always
processing the last processed MIDI substream if the last USB request wasn't
enought to handle the whole stream.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This ensures that the midi function will only work if the proper number of
IN and OUT requrests are allocated. Otherwise the function will work with less
requests then what the user wants.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This avoids duplication of USB requests for OUT endpoint and
re-enabling endpoints.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When reloading omap2430 kernel module we get a warning about
unbalanced pm_runtime_enable. Let's fix this. Note that we
need to do this after the child musb-core platform_device is
removed because of pm_runtime_irq_safe being set at the child.
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We currently can't unload omap2430 MUSB platform glue driver module and
this cause issues for fixing the MUSB code further. The reason we can't
remove omap2430 is because it uses the PHY functions and also exports the
omap_musb_mailbox function that some PHY drivers are using.
Let's fix the issue by exporting a more generic musb_mailbox function
from the MUSB core and allow platform glue layers to register phy_callback
function as needed.
And now we can now also get rid of the include/linux/musb-omap.h.
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes redundant condition.
(!A || (A && B)) is the same as (!A || B).
Fixes indentation too.
Tested by: compilation only
Caught by: cppcheck
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes redundant condition.
(!A || (A && B)) is the same as (!A || B).
Tested by compilation only.
Caught by cppcheck.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change behavior during registration of gadgets and
gadget drivers in udc-core. Instead of previous
approach when for successful probe of usb gadget driver
at least one usb gadget should be already registered
use another one where gadget drivers and gadgets
can be registered in udc-core independently.
Independent registration of gadgets and gadget drivers
is useful for built-in into kernel gadget and gadget
driver case - because it's possible that gadget is
really probed only on late_init stage (due to deferred
probe) whereas gadget driver's probe is silently failed
on module_init stage due to no any UDC added.
Also it is useful for modules case - now there is no
difference what module to insert first: gadget module
or gadget driver one.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
[simplified code as requested by Alan Stern and Felipe Balbi,
fixed checkpatch issues]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now when last user of usb_udc_attach_driver() is switched
to passing UDC name via usb_gadget_driver struct, it's safe
to remove this function
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now when udc-core supports binding to specific UDC by passing
its name via 'udc_name' member of usb_gadget_driver struct,
switch to this generic approach.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
[rebased and fixed checkpatch issues]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introduce new 'udc_name' member to usb_gadget_driver structure.
The 'udc_name' is a name of UDC that usb_gadget_driver should
be bound to. If udc_name is NULL, it will be bound to any
available UDC.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To prevent VBUS contention, the am335x MUSB phy senses VBUS first before
transitioning to host mode. However, for host-only mode, VBUS could be
directly tied to 5V power rail which could prevent MUSB transitions to
host mode.
This change receives dr_mode of the controller then bypass the first
VBUS sensing for host-only mode, so that MUSB can work in host mode
event if VBUS is tied to 5V.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The filename of am35x-phy-control.h is confusing. The header is used
by the am335x phy driver, but the filename refers to am35x. Even worse
there is indeed another device called am35x but it does not use this
header at all.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As of commit 3d7608e4c1 ("ARM: shmobile: bockw: remove legacy
board file and config"), the Renesas R-Car (Gen1) USB PHY driver is no
longer used.
In theory it could still be used on R-Car Gen1 SoCs, but that would
require adding DT support to the driver. Instead, a new driver using the
generic PHY framework should be written, as was done for R-Car Gen2.
Remove the driver for good.
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove mach/irq.h from the list of included headers, there is no
compilation dependency on this include file, and the change is needed
to prevent a compilation failure, when mach/irq.h is removed.
Additionally remove other unneeded includes and sort out their order.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct usb_request have 3 flags which might be
important to know about during debug. This patch
shows each of the 3 flags as a single letter:
z -> for zero
s -> short not okay
i -> interrupt
A capital letter means the feature is enabled
while a lower case letter means it is disabled;
Thus 'zsI' indicates that a ZLP is not needed,
that we can accept a short packet and interrupt
for this request should be enabled.
Signed-off-by: Felipe Balbi <balbi@ti.com>
So far, dwc3 has always missed request->zero
handling for every endpoint. Let's implement
that so we can handle cases where transfer must
be finished with a ZLP.
Note that dwc3 is a little special. Even though
we're dealing with a ZLP, we still need a buffer
of wMaxPacketSize bytes; to hide that detail from
every gadget driver, we have a preallocated buffer
of 1024 bytes (biggest bulk size) to use (and
share) among all endpoints.
Reported-by: Ravi B <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This file already uses pr_debug in a few places; this converts the
remaining printks.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In general it is wise to clear interrupts before processing them. If
you don't do that, you can get:
1. Interrupt happens
2. You look at system state and process interrupt
3. A new interrupt happens
4. You clear interrupt without processing it.
This patch was actually a first attempt to fix missing device insertions
as described in (usb: dwc2: host: Fix missing device insertions) and it
did solve some of the signal bouncing problems but not all of
them (which is why I submitted the other patch). Specifically, this
patch itself would sometimes change:
1. hardware sees connect
2. hardware sees disconnect
3. hardware sees connect
4. dwc2_port_intr() - clears connect interrupt
5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()
...to:
1. hardware sees connect
2. hardware sees disconnect
3. dwc2_port_intr() - clears connect interrupt
4. hardware sees connect
5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()
...but with different timing then sometimes we'd still miss cable
insertions.
In any case, though this patch doesn't fix any (known) problems, it
still seems wise as a general policy to clear interrupt before handling
them.
Note that for dwc2_handle_usb_port_intr(), instead of moving the clear
of PRTINT to the beginning of the function we remove it completely. The
only way to clear PRTINT is to clear the sources that set it in the
first place.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2_hcd_reset_func() function is only ever called directly by a
delayed work function. As such no locks are already held when the
function is called.
Doing a read-modify-write of CPU registers and setting fields in the
main hsotg data structure is a bad idea without locks. Let's add
locks.
The bug was found by code inspection only. It turns out that the
dwc2_hcd_reset_func() is only ever called today if the
"host_support_fs_ls_low_power" parameter is enabled and no code in
mainline enables that parameter. Thus no known issues in mainline are
fixed by this patch, but it's still probably wise to fix the function.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some USB phy drivers have different handling for the controller in each
dr_mode. But the phy driver does not have visibility to the dr_mode of
the controller.
This adds an api to return the dr_mode of the controller which
associates the given phy node.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since now, we may have more than one request during the test, and
it is better we just quit once the error occurs instead of try
queueing further requests.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Suggested-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since composite now overwrites bcdUSB for any gadget, remove
setting it in legacy gadgets. All legacy gadgets set 0x0200, the
same as the value additionally set by composite, so there is no
behaviour change.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Rebase onto current balbi/next
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In some cases, like when you've got a "Microsoft Wireless Keyboard 2000"
connected to dwc2 with a hub, expected that we'll get some transfer
errors sometimes. The controller is expected to try at least 3 times
before giving up. See figure "Figure A-67. Normal HS CSPLIT 3 Strikes
Smash" in the USB spec.
The dwc2 controller has a way to support this by using the "EC_MC"
field. The Raspberry Pi driver has logic for setting this right. See
fiq_fsm_queue_split_transaction() in their "dwc_otg_hcd.c". Let's use
the same logic.
After making this change, we no longer get dropped characters from the
above mentioned keyboard. Other devices on the same bus as the keyboard
also behave more properly.
Thanks for Julius Werner for the expert analysis and suggestions.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If you've got your interrupt signals bouncing a bit as you insert your
USB device, you might end up in a state when the device is connected but
the driver doesn't know it.
Specifically, the observed order is:
1. hardware sees connect
2. hardware sees disconnect
3. hardware sees connect
4. dwc2_port_intr() - clears connect interrupt
5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()
Now you'll be stuck with the cable plugged in and no further interrupts
coming in but the driver will think we're disconnected.
We'll fix this by checking for the missing connect interrupt and
re-connecting after the disconnect is posted. We don't skip the
disconnect because if there is a transitory disconnect we really want to
de-enumerate and re-enumerate.
Notes:
1. As part of this change we add a "force" parameter to
dwc2_hcd_disconnect() so that when we're unloading the module we
avoid the new behavior. The need for this was pointed out by John
Youn.
2. The bit of code needed at the end of dwc2_hcd_disconnect() is
exactly the same bit of code from dwc2_port_intr(). To avoid
duplication, we refactor that code out into a new function
dwc2_hcd_connect().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Support hisilicon,hi6220-usb for HiKey board
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Kmem caches help to get correct boundary for descriptor buffers
which need to be 512 bytes aligned for dwc2 controller.
Two kmem caches are needed for generic descriptors and for
hs isochronous descriptors which doesn't have same size.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Masks for HCDMA.CTD and HCDMA.DMAAddr are incorrect. As we always
start from first descriptor, no need to mask the address anyway.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use Streaming DMA mappings to handle cache coherency of frame list and
descriptor list. Cache are always flushed before controller access it
or before cpu access it.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As descriptor dma mode does not support split transfers, it can't be
enabled for high speed devices. Add a core parameter to enable it for
full speed devices.
Ensure frame list and descriptor list are correctly freed during
disconnect.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
timeval is deprecated and not y2038 safe. Its size also changes according
to 32 bit/ 64 bit compilation. Replace it with 32 and 64 bit versions of
its individual fields, giving two ioctls with different code values.
The two ioctls are necessary to maintain the 32 bit and 64 bit userspace
compatibility with a 64/32 bit kernel.
Change unsigned to __u32 types for a definitive userspace interface.
This is in accordance with the psABI that the unsigned type is always
32 bits.
Also use motonic timer instead of real time to ensure positive delta
values.
Refactor usbtest_ioctl for readability to isolate the handling of the
testing timing measurement.
The official testusb userspace tool can be changed in a separate patch
to reflect the __u32 changes as well. It can use the usbtest_param_32
struct, since 32 bit seconds is long enough for test durations.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove unnecessary headers and variables.
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This function is shared between gadget functions, so this avoid unnecessary
duplicated code and potentially avoid memory leaks.
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This code is duplicated from f_midi_start_ep(midi, f, midi->out_ep).
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch modifies the ep.caps.type_{iso,bulk,int} setting and
the second argument of usb_ep_maxpacket_limit() using
the dparam.pipe_configs.
In the previous code, all the type_{iso,bulk,int} were set to true.
However, to avoid waste time for finding suitable pipe in usb_ep_enable(),
this driver should set correct type.
Also the second argument of usb_ep_maxpacket_limit() was set to 512
even if the pipe is isochronous or interrupt. So, this driver could
not bind a gadget driver like the g_audio driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The current code has info->bufnmb_last to calculate the BUFNMB bits of
PIPEBUF register. However, since the bufnmb_last is initialized in
the usbhs_pipe_init() only, this driver is possible to set unexpected
value to the register if usb_ep_{enable,disable}() are called many times.
So, this patch modifies the pipe configuration via struct
renesas_usbhs_driver_param to simplify the code. Also this patch changes:
- a double buffer configuration
- isochronous buffer size from 512 to 1024
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Process all completed urbs, if more urbs are complete by the time
driver processes completion interrupt.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When releasing a channel, increment hsotg->available_host_channels even
in case a periodic channel is released.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Isochronous descriptor is currently programmed for the frame
after the last descriptor was programmed.
If the last descriptor frame underrun, then current descriptor must
take this into account and must be programmed on the current frame + 1.
This overrun usually happens when system is loaded and dwc2 can't init
descriptor list in time.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This function allow comparing frame index used for
descriptor list which has 64 entries.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Prevent dwc2 driver from accessing channel while it frees it.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When completing non isoc xfer, dwc2_complete_non_isoc_xfer_ddma()
is relying on qtd->n_desc to process the corresponding number of
descriptors.
During the processing of these descriptors, qtd could be unlinked
and freed if xfer is done and urb is no more in progress.
In this case, dwc2_complete_non_isoc_xfer_ddma() will read again
qtd->n_desc whereas qtd has been freed. This will lead to unpredictable
results since qtd->n_desc is no more valid value.
To avoid this error, return a result != 0 in dwc2_process_non_isoc_desc(),
so that dwc2_complete_non_isoc_xfer_ddma() stops desc processing.
This has been seen with Slub debug enabled.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a channel is halted because of urb dequeue during transfer
completion, no other qtds must be scheduled until halt is done.
Moreover, all in progress qtds must be given back.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Active bit must be enabled in all scheduled descriptors. Else transfer
never start.
Remove previous code which was not correctly configuring descriptors.
Active bit was set before calling dwc2_fill_host_isoc_dma_desc() which
is erasing dma_desc->status.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Increment qtd->isoc_frame_index_last before testing it, else below
check will never be true and IOC (Interrupt On Complete) bit for
last frame will never be set in descriptor status.
/* Set IOC for each descriptor corresponding to last frame of URB */
if (qtd->isoc_frame_index_last == qtd->urb->packet_count)
dma_desc->status |= HOST_DMA_IOC;
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now the function of complicated_callback is not only used for iso
transfer, improve the error message to reflect it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add queue depth for both iso and bulk transfer, with more queues, we
can do performance and stress test using sourcesink, and update g_zero
accordingly.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that we have a generic dwc3-of-simple.c, we can
use that instead of maintaining dwc3-qcom.c which is
extremely similar.
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For simple platforms which merely enable some clocks
and populate its children, we can use this generic
glue layer to avoid boilerplate code duplication.
For now this supports Qcom and Xilinx, but if we
find a way to add generic handling of regulators and
optional PHYs, we can absorb exynos as well.
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It just ocurred to me that dwc3 already gives a
really hint of when a setup packet is pending and
that's the SETUP_PENDING TRB Status for EP0 IRQs.
Fix setup_packet_pending initialization based on
that. While at that, also make sure the comment in
gadget.c matches what code is doing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In dwc3_cleanup_done_reqs() we expect that all
iterations of our while (1) loop will find a valid
struct dwc3_request *. In case we don't, we're
dumping a WARN_ON_ONCE() splat so that people report
the failure.
This patch is a simple cleanup converting:
if (!req) {
WARN_ON_ONCE(1);
return 1;
}
to:
if (WARN_ON_ONCE(!req))
return 1;
which is a little easier to read.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
By moving our sanity checks our internal function
__dwc3_gadget_ep_queue() we can simplify the
externally visible API while also making sure that
callers of __dwc3_gadget_ep_queue() also make use of
the same checks.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Cc: stable <stable@vger.kernel.org>
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes redundant condition.
(length && length > 5) can be reduced to a single evaluation.
Tested by compilation only.
Caught by cppcheck.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch removes redundant conditions.
(!A || (A && B)) is the same as (!A || B).
Tested by compilation only.
Caught by cppcheck.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Hopefully final set of fixes for v4.4 release cycle.
There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.
A NULL pointer dereference fix for the MSM phy driver.
The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o5zI
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for-v4.4-rc5
Hopefully final set of fixes for v4.4 release cycle.
There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.
A NULL pointer dereference fix for the MSM phy driver.
The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
removed write permission for writeable attributes. Correct attribute
permissions.
Fixes: 76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If musb_init_controller fails at musb_platform_init, we have already
called pm_runtime_irq_safe for musb and that causes the pm runtime count
to be enabled for parent before the parent has completed initialization.
This causes pm to stop working as on unload nothing gets idled.
This issue can be reproduced at least with:
# modprobe omap2430
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
# modprobe phy-twl4030-usb
# rmmod omap2430
And after the steps above omap2430 will block deeper idle states on
omap3.
To fix this, let's not enable pm runtime until we need to and the
parent has been initialized. Note that this does not fix the issue of
PM being broken for musb during runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Even if the probability of this case is very low, fixing it made
static analyzers happy.
Solving this with of_device_get_match_data made also code simplier.
Reported-by: coverity (CID 1324133)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When assigning bool use true instead of 1. If declaring it as static and
it's false there's no need to initialize it, since static variables are
zeroed by default.
Caught by coccinelle.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module should fail to load.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It shouldn't matter how usbcore is compiled. As it is a subsystem,
the correct way to use nousb should be usbcore.nousb
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace BUG() with BUG_ON().
Caught by coccinelle.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of bool explicit comparisons.
Caught by Coccinelle.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently usb_port_resume waits for up to 2 seconds for CONNECT
status for SS devices only. This change will do the same thing for
non-SS devices even though the reason is a little different. This
will fix an issue where VBUS is turned off during system wide
"suspend to ram" and some 2.0 devices take greater than the current
max of 100ms to show connected after VBUS is enabled. This is most
commonly seen on hard drive based devices and USB3.0 devices plugged
into a 2.0 only port.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt handler, ohci_hcd_at91_overcurrent_irq may be called right
after registration. At that time, pdev->dev.platform_data is not yet set,
leading to a NULL pointer dereference.
Fixes: e4df92279f (USB: host: ohci-at91: merge loops in ohci_hcd_at91_drv_probe)
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.3+
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My recent Intel box is spewing these messages:
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 4.3.0+ xhci-hcd
usb usb2: SerialNumber: 0000:00:14.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
usb: failed to peer usb2-port2 and usb1-port1 by location (usb2-port2:none) (usb1-port1:usb2-port1)
usb usb2-port2: failed to peer to usb1-port1 (-16)
usb: port power management may be unreliable
usb: failed to peer usb2-port3 and usb1-port1 by location (usb2-port3:none) (usb1-port1:usb2-port1)
usb usb2-port3: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port5 and usb1-port1 by location (usb2-port5:none) (usb1-port1:usb2-port1)
usb usb2-port5: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port6 and usb1-port1 by location (usb2-port6:none) (usb1-port1:usb2-port1)
usb usb2-port6: failed to peer to usb1-port1 (-16)
Diving into the acpi tables, I noticed the EHCI hub has 12 ports while the XHCI
hub has 8 ports. Most of those ports are of connect type USB_PORT_NOT_USED
(including port 1 of the EHCI hub).
Further the unused ports have location data initialized to 0x80000000.
Now each unused port on the xhci hub walks the port list and finds a matching
peer with port1 of the EHCI hub because the zero'd out group id bits falsely match.
After port1 of the XHCI hub, each following matching peer will generate the
above warning.
These warnings seem to be harmless for this scenario as I don't think it
matters that unused ports could not create a peer link.
The attached patch utilizes that assumption and just turns the pr_warn into
pr_debug to quiet things down.
Tested on my Intel box.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a memory leak because acpi_evaluate_dsm() actually returns an
object which the caller is supposed to release. Fix this by calling
ACPI_FREE() for the returned object (this expands to kfree() so passing
NULL there is fine as well).
While there correct indentation in !CONFIG_ACPI case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.2
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 LPM is default on in Linux kernel if both xHCI host controller
and the USB devices declare to be LPM-capable. Unfortunately, some
devices are known to work well with LPM disabled, but to be broken
if LPM is enabled, although it declares the LPM capability. Users
won't be able to use this kind of devices, until someone puts them
in the kernel blacklist and gets the kernel upgraded.
This patch adds a sysfs node to permit or forbit USB3 LPM U1 or U2
entry for a port. The settings apply to both before and after device
enumeration. Supported values are "0" - neither u1 nor u2 permitted,
"u1" - only u1 is permitted, "u2" - only u2 is permitted, "u1_u2" -
both u1 and u2 are permitted. With this interface, users can use an
LPM-unfriendly USB device on a released Linux kernel.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 655fe4effe ("usbcore: add sysfs support to xHCI usb3
hardware LPM") introduced usb3_hardware_lpm sysfs node. This
doesn't show the correct status of USB3 U1 and U2 LPM status.
This patch fixes this by replacing usb3_hardware_lpm with two
nodes, usb3_hardware_lpm_u1 (for U1) and usb3_hardware_lpm_u2
(for U2), and recording the U1/U2 LPM status in right places.
This patch should be back-ported to kernels as old as 4.3,
that contains Commit 655fe4effe ("usbcore: add sysfs support
to xHCI usb3 hardware LPM").
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets the AHBMODE to allow for posted data writes. This
results in higher performance.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Tested-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets the AHBMODE to allow for posted data writes. This
results in higher performance.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct mon_bin_hdr allows for a 64-bit seconds timestamp. The code
currently uses 'struct timeval' to populate the timestamp in mon_bin_hdr,
which has a 32-bit seconds field and will overflow in year 2038 and beyond.
This patch replaces 'struct timeval' with 'struct timespec64' which is
y2038 safe. This patch is part of a larger attempt to remove instances
of struct timeval and other 32-bit timekeeping (time_t, struct timespec)
from the kernel.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
timeval is deprecated and not y2038 safe. Its size also changes according
to 32 bit/ 64 bit compilation. Replace it with 32 and 64 bit versions of
its individual fields, giving two ioctls with different code values.
The two ioctls are necessary to maintain the 32 bit and 64 bit userspace
compatibility with a 64/32 bit kernel.
Change unsigned to __u32 types for a definitive userspace interface.
This is in accordance with the psABI that the unsigned type is always
32 bits.
Also use motonic timer instead of real time to ensure positive delta
values.
Refactor usbtest_ioctl for readability to isolate the handling of the
testing timing measurement.
The official testusb userspace tool can be changed in a separate patch
to reflect the __u32 changes as well. It can use the usbtest_param_32
struct, since 32 bit seconds is long enough for test durations.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct timeval' uses 32-bits for its seconds field and will overflow in
the year 2038 and beyond. This patch replaces the usage of 'struct timeval'
in mon_get_timestamp() with timespec64 which uses a 64-bit seconds field
and is y2038-safe. mon_get_timestamp() truncates the timestamp at 4096 seconds,
so the correctness of the code is not affected. This patch is part of a larger
attempt to remove instances of struct timeval and other 32-bit timekeeping
(time_t, struct timespec) from the kernel.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far we were using simple (legacy) GPIO functions & some poor logic to
control power. It got many drawbacks: we were ignoring OF flags
(GPIO_ACTIVE_LOW), we were not setting direction to output and we were
assuming gpio_request success all the time.
Fix it by switching to gpiod functions and adding appropriate checks.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.
Fixes: ff30cbc8da ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qset_fill_page_list() do not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB 3.0 mass storage device is disconnected in transporting
state, storage device driver may handle it as a transport error and
reset the device by invoking usb_reset_and_verify_device()
and following could happen:
in usb_reset_and_verify_device():
udev->bos = NULL;
For U1/U2 enabled devices, driver will disable LPM, and in some
conditions:
from usb_unlocked_disable_lpm()
--> usb_disable_lpm()
--> usb_enable_lpm()
udev->bos->ss_cap->bU1devExitLat;
And it causes 'NULL pointer' and 'kernel panic':
[ 157.976257] Unable to handle kernel NULL pointer dereference
at virtual address 00000010
...
[ 158.026400] PC is at usb_enable_link_state+0x34/0x2e0
[ 158.031442] LR is at usb_enable_lpm+0x98/0xac
...
[ 158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0
[ 158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac
[ 158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4
...
[ 158.214954] Kernel panic - not syncing: Fatal exception
This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm()
to prevent from NULL pointer access.
Issue can be reproduced by following setup:
1) A SS pen drive behind a SS hub connected to the host.
2) Transporting data between the pen drive and the host.
3) Abruptly disconnect hub and pen drive from host.
4) With a chance it crashes.
Signed-off-by: Hans Yang <hansy@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_mon_operations structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the function of complicated_callback is not only used for iso
transfer, improve the error message to reflect it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
for checking if a property is present or not,
of_property_read_bool is more appropriate than of_get_property()
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function must be called with a spinlock held.
Memory can be allocated only with GFP_ATOMIC. Passing
a gfp_t argument is a waste.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use this macro to make the driver more readable.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma_pool_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
replace dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the existing two extended capability parsing helper functions with
one called xhci_find_next_ext_cap().
The extended capabilities are read both in pci-quirks before xhci driver is
loaded, and inside the xhci driver when adding ports. The existing helpers
did not suit well for these cases and a lot of custom parsing code was
needed.
The new helper function simplifies these two cases a lot.
The motivation for this rework was that code to support xhci debug
capability needed to parse extended capabilities, and it included
yet another capability parsing helper specific for its needs. With
this solution it debug capability code can use this new helper as well
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use dev_warn() for intened behaviour, use dev_dbg()
Rounding down the interval to the nearest power of 2 is required
by xhci specs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reseved
DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is
8 times as much as that defined in xHCI spec.
3. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The R-Car H3 has two xHCI controllers. This SoC is compatible with
R-Car Gen2 SoCs, however this SoC doesn't need some specific registers
setting, and need a new firmware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for R-Car M2-N (r8a7793) xHCI controller.
This SoC is compatible with R-Car H2 (r8a7790) and R-Car M2-W (r8a7791).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes code to ease the addition of next generation SoCs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a member "firmware_name" in struct xhci_plat_priv
to simplify the code to match specific firmware name.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds struct xhci_plat_priv to simplify the code to match
platform specific variables. For now, this patch adds a member "type"
in the structure.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an xhci->priv field for private use by
XHCI platform drivers. Until now none of the platform drivers
has used this private space.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleanups the hcd private size to suitable size.
The previous code has "sizeof(struct xhci_hcd *)" in xhci_hc_driver
as hcd_priv_size and sizeof(struct xhci_hcd) in xhci_plat_overrides
or xhci_pci_overrides as extra_priv_size. However, the xhci driver
uses a "sizeof(struct xhcd_hcd)" memory space in each hcd
(main_hcd and shared_hcd) actually.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use the variables defined for populating the port status and
port chage bits retuend by GetPortStatus request intead of
the hub class feature selectors.
The defines for hub class feature selectors are used for other purposes,
they work as port status and feature selectors are in the same order, and
set the same bits, but it makes the code very hard to follow
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a new warning message to ehci-hcd. The warning is
triggered whenever the driver finds that the hardware has set the
Active bit in a QH at a time when the driver expects the QH to be
completely idle. Such bugs have been observed by users in the past,
and since they can lead to serious problems (such as inability to
unlink an URB that never completes), it would be good to know about
them when they occur.
This won't fix these bugs; that's a bigger job for a later patch. But
success isn't guaranteed, since this depends on aspects of the
hardware which are not documented in the EHCI spec or for which the
spec's recommendations are clearly unworkable. It therefore seems
worthwhile to check for these bugs proactively.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Reutman <mreutman@epiqsolutions.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enhances the "async" debugfs file in ehci-hcd by printing
out several additional fields in the hardware-accessible data
structures. These fields are important for determining the hardware's
view of the async schedule, in particular, the addresses of the
current and next qTDs for each QH along with the start address of each
qTD's data buffer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch improves the usbfs_snoop debugging facility by adding
messages for a couple of significant events which, up to now, have not
been logged. The events are reaping and discarding (i.e.,
cancelling) an URB. The debugging messages include the userspace
address of the URB being reaped or discarded.
The reaping messages have to be added in four places, in order to
handle blocking and non-blocking reaps in both normal and 32-bit
compatibility mode.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbfs_snoop facility can be very useful for debugging problems
involving usbfs. However, it always prints out the entire contents of
every URB. When dealing with large quantities of data, this can be
less than helpful.
This patch ameliorates the situation by adding a module parameter to
usbcore for controlling the maximum number of bytes to print when
snooping an URB. This makes debugging much easier. For backward
compatibility, the default value is set unreasonably high.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch extends the family of SATA-to-USB JMicron adapters that need
FUA to be disabled and applies the same policy for uas driver.
See details in http://unix.stackexchange.com/questions/237204/
Signed-off-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Tested-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like other buggy models that had their fixes [1], the touchscreen with
id 04f3:21b8 from ELAN Microelectronics needs the device-qualifier
quirk. Otherwise, it fails to respond, blocks the boot for a random
amount of time and pollutes dmesg with:
[ 2887.373196] usb 1-5: new full-speed USB device number 41 using xhci_hcd
[ 2889.502000] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2889.502005] usb 1-5: can't read configurations, error -71
[ 2889.654571] usb 1-5: new full-speed USB device number 42 using xhci_hcd
[ 2891.783438] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2891.783443] usb 1-5: can't read configurations, error -71
[1]: See commits c68929f, 876af5d, d749947, a32c99e and dc703ec.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some device-id fixes that remove a HID device from cp210x, and
adds support for another Infineon flash-loader device. The flash-loader
device presents itself as a CDC-ACM device even though it is clearly
not, so we need to blacklist it in the cdc-acm driver as well.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=JdcP
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.4-rc3
Here are some device-id fixes that remove a HID device from cp210x, and
adds support for another Infineon flash-loader device. The flash-loader
device presents itself as a CDC-ACM device even though it is clearly
not, so we need to blacklist it in the cdc-acm driver as well.
Signed-off-by: Johan Hovold <johan@kernel.org>
Here's our second round of fixes. Some of the bugs are pretty old like
the one on pxa27x suspend implementation.
The most important part is a randbuild warning fix on MUSB CPPI DMA
engine by Arnd, a couple fixes by Felipe Tonello on f_midi (first one
makes sure we only transmit on enabled ep IN while second plugs a memory
leak) and a NULL pointer dereference fix on renesas usbhs.
Note that we also have a new compatible string being added for the MXS
PHY.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qfZS
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.4-rc3
Here's our second round of fixes. Some of the bugs are pretty old like
the one on pxa27x suspend implementation.
The most important part is a randbuild warning fix on MUSB CPPI DMA
engine by Arnd, a couple fixes by Felipe Tonello on f_midi (first one
makes sure we only transmit on enabled ep IN while second plugs a memory
leak) and a NULL pointer dereference fix on renesas usbhs.
Note that we also have a new compatible string being added for the MXS
PHY.
Because interrupt endpoints usually transmit such
small amounts of data, it seems pointless to prestart
transfers and try to get speed improvements. This
patch also sorts out a problem with CDC ECM function
where its notification endpoint gets stuck in busy
state and we continuously issue Update Transfer
commands.
Fixes: 8a1a9c9e45 ("usb: dwc3: gadget: start transfer on XFER_COMPLETE")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added tx_empty callback needed for generic wait-until-sent support.
Without this function, when the port is closed usbserial can't know that
there are still data in the chip's transmit FIFO. The chip gets disabled
and untransmitted data lost. When the actual byte count is reported by
tx-empty the close can be delayed until all data are sent.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: modify tx_empty error handling ]
Signed-off-by: Johan Hovold <johan@kernel.org>
This allows to write
drm-$(CONFIG_AGP) += drm_agpsupport.o
without having to handle CONFIG_AGP=y vs. CONFIG_AGP=m. Only support
this syntax for modules, since built-in code depending on something
modular cannot work and init/Makefile actually relies on the current
semantics. There are a few drivers which adapted to the current
semantics out of necessity; these are fixed to also work when the
respective subsystem is modular.
Acked-by: Peter Chen <peter.chen@freescale.com> [chipidea]
Signed-off-by: Michal Marek <mmarek@suse.com>
For historic reasons, the tegra platform selects USB_ULPI from architecture
code, but that hasn't really made sense for a long time, as the only
user of that code is the Tegra EHCI driver that has its own Kconfig
symbol.
This removes the 'select' statements from mach-tegra and drivers/soc/tegra
and adds them with the device driver that actually needs them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The flash loader has been seen on a Telit UE910 modem. The flash loader
is a bit special, it presents both an ACM and CDC Data interface but
only the latter is useful. Unless a magic string is sent to the device
it will disappear and the regular modem device appears instead.
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some modems, such as the Telit UE910, are using an Infineon Flash Loader
utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC
Data). The latter can be used as a serial interface to upgrade the
firmware of the modem. However, that isn't possible when the cdc-acm
driver takes control of the device.
The following is an explanation of the behaviour by Daniele Palmas during
discussion on linux-usb.
"This is what happens when the device is turned on (without modifying
the drivers):
[155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci
[155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11
[155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041
[155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
This is the flashing device that is caught by the cdc-acm driver. Once
the ttyACM appears, the application starts sending a magic string
(simple write on the file descriptor) to keep the device in flashing
mode. If this magic string is not properly received in a certain time
interval, the modem goes on in normal operative mode:
[155493.748094] usb 1-3: USB disconnect, device number 27
[155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci
[155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021
[155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM
[155495.059989] usb 1-3: Manufacturer: Telit
[155495.059992] usb 1-3: SerialNumber: 359658044004697
[155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
[155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device
[155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device
[155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device
[155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device
[155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device
[155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14
Using the cdc-acm driver, the string, though being sent in the same way
than using the usb-serial-simple driver (I can confirm that the data is
passing properly since I used an hw usb sniffer), does not make the
device to stay in flashing mode."
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID
and completely different from CP210x devices.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch make sure that all necessary members of dwc2_hsotg
are initialized before the irq handler is requested. So
the kernel oops triggered by dwc2_handle_common_intr has
been fixed.
dwc2 20980000.usb: Configuration mismatch. Forcing host mode
dwc2 20980000.usb: no platform data or transceiver defined
Unable to handle kernel paging request at virtual address cc860040
pgd = c0004000
[cc860040] *pgd=0b41e811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc3+ #19
Hardware name: BCM2835
task: cb494000 ti: cb4d0000 task.ti: cb4d0000
PC is at dwc2_is_controller_alive+0x18/0x34
LR is at dwc2_handle_common_intr+0x24/0xb60
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is not permitted to set task state before lock. usblp_wwait sets
the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible.
Upon return from that function, the state will be TASK_RUNNING again.
This is clearly a bug and a warning is generated with LOCKDEP too:
WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp]
Modules linked in: ...
CPU: 1 PID: 5109 Comm: captmon Tainted: G W 4.2.5-0.gef2823b-default #1
Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012
ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000
ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282
ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508
Call Trace:
...
[<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50
[<ffffffff8109a8bd>] __might_sleep+0x7d/0x90
[<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0
[<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp]
[<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp]
[<ffffffff8121ed98>] __vfs_write+0x28/0xf0
...
Commit 7f477358e2 (usblp: Implement the
ENOSPC convention) moved the set prior locking. So move it back after
the lock.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: 7f477358e2 ("usblp: Implement the ENOSPC convention")
Acked-By: Pete Zaitcev <zaitcev@yahoo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When choose randconfig for kernel build, it reports below warning:
"warning: (USB_OTG_FSM && FSL_USB2_OTG && USB_MV_OTG) selects USB_OTG
which has unmet direct dependencies (USB_SUPPORT && USB && PM)"
In fact, USB_OTG is visible symbol and depends on PM, so the driver
needs to depend on it to reduce dependency problem.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b01 Rev=02.32
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Now all important things are there:
wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)
There is also ttyUSB0, but it is not usable, at least not for at.
The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids, support for an odd qcserial Gobi interface
layout and a fix for the qcserial Huawei interface layout.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJWTZ9dAAoJEEEN5E/e4bSVNQMP/3XoMFHKYZ+PvYwwiBoQSm7R
OH1s+u4LttDcieLiyBCtWe3lE+8ennAglBmirseXhl5scBfZJdgGsMnhXnN4KN1P
qWkPNiGme68xlJmJU44uB/EDq4mknASclf8NKxK0L9RqrcPv//6O/WgsgVzpXeJt
BVL4dTfof0N2y2o8/PO/4sFV0Q+i0iyughTi1NsGTJIocO8Gs/Xps6zBTnh0KMnx
Cdu00ymmAAbg6OidesR19FraY+YTZQL5Na+wnky6AfHb3zgSYdhwxvPgoeDvFqdU
n9XvxYbGj7ZzrEV7BdRQb6BHYsFwU/tTdsKuxSEX2SRSgsS69XiQuwFg7vQfdTHx
2DSEI5enSztddfxbz0g5xqeUENoiEAajsVFUbLNABaM+EsYoQHcdhEFqGczdHdYv
T6Dbuz/BfSPE5guBb9AonvTegKVKg5MfGFT+HL5B7mW5ADM1YucKrdhragyS5HzS
O1HY2rgBW72rA6GnKGheL45b8IjK2rCe2W99j89gIwUBzVO/5WL1a4pIHz6/RSW6
N8jR4QqW0USaPCe1mKHFT+mfAgo0HU3GhG0FaGYt8e07YnmMGEITT90za3HyEQhY
WmTQVJoaL6zd8SPoLP7+PC2LUDNDJWjuXVLDzAvnCBF1YBvNePFJDlETwUvbH9Ho
FzGd7Dch5DfxhF5H2CGu
=YaM3
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.4-rc2
Here are some new device ids, support for an odd qcserial Gobi interface
layout and a fix for the qcserial Huawei interface layout.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add "fsl,imx6ul-usbphy" compatible string for iMX6ul usb phy
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes a memory leak that occurs when an endpoint fails to enqueue
the request. If that happens the complete function will never be called, thus
never freeing the request.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes sure f_midi doesn't try to enqueue data when the IN endpoint is
disabled, ie, USB cable is disconnected.
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes commit 09a75e8577
("usb: dwc2: refactor common low-level hw code to platform.c")
The above commit consolidated the low-level phy access into a common
location. This change made the otg clk a requirement and broke some
platforms when it was moved into platform.c.
So make clk handling optional again.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 09a75e8577 ("usb: dwc2: refactor common low-level hw code to platform.c")
Signed-off-by: Felipe Balbi <balbi@ti.com>
When searching for PHYs, any error was treated as if the PHY did not
exist or was not specified. Thus the probe function did not
correctly return error conditions such as -EPROBE_DEFER.
Fixed so that only a non-existing PHY is ignored and any other error
is returned.
Acked-by: Eric Anholt <eric@anholt.net>
Reported-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes commit 09a75e8577
("usb: dwc2: refactor common low-level hw code to platform.c")
The above commit consolidated the low-level phy access into a common
location. This change introduced a check from the gadget requiring
that a PHY is specified. This requirement never existed on the host
side and broke some platforms when it was moved into platform.c.
The gadget doesn't require the PHY either so remove the check.
Acked-by: Eric Anholt <eric@anholt.net>
Reported-by: Stefan Wahren <info@lategoodbye.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 09a75e8577 ("usb: dwc2: refactor common low-level hw code to platform.c")
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that NULL pointer dereference happens when
a gadget driver calls usb_ep_dequeue() for ep0 after disconnected
a usb cable. This is because that usbhsg_try_stop() will call
usbhsg_ep_disable(&dcp->ep) when a usb cable is disconnected and
the pipe of dcp (ep0) is set to NULL.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When choose randconfig for kernel build, it reports below warning:
"warning: (USB_OTG_FSM && FSL_USB2_OTG && USB_MV_OTG) selects USB_OTG
which has unmet direct dependencies (USB_SUPPORT && USB && PM)"
In fact, USB_OTG is visible symbol and depends on PM, so the driver
needs to depend on it to reduce dependency problem.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
pxa27x disconnects pullups on suspend but doesn't
notify the gadget driver about it, so gadget driver
can't disable the endpoints it was using.
This causes problems on resume because gadget core
will think endpoints are still enabled and just
ignore the following usb_ep_enable().
Fix this problem by calling
gadget_driver->disconnect().
Cc: <stable@vger.kernel.org> # v3.10+
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use safe copy_*_user instead of unsafe __copy_*_user
functions when accessing userland memory.
Signed-off-by: Daniel Walter <dwalter@sigma-star.at>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The CPPI-4.1 driver selects TI_CPPI41, which is a dmaengine
driver and that may not be available when CONFIG_DMADEVICES
is not set:
warning: (USB_TI_CPPI41_DMA) selects TI_CPPI41 which has unmet direct dependencies (DMADEVICES && ARCH_OMAP)
This adds an extra dependency to avoid generating warnings in randconfig
builds. Ideally we'd remove the 'select' statement, but that has the
potential to break defconfig files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 411dd19c68 ("usb: musb: Kconfig: Select the DMA driver if DMA mode of MUSB is enabled")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Clear device initiated resume variables once device is fully up and running
in U0 state.
Resume needs to be signaled for 20ms for usb2 devices before they can be
moved to U0 state.
An interrupt is triggered if a device initiates resume. As we handle the
event in interrupt context we can not sleep for 20ms, so we instead set
a resume flag, a timestamp, and start the roothub polling.
The roothub code will later move the port to U0 when it finds a port in
resume state with the resume flag set, and timestamp passed by 20ms.
A host initiated resume is however not done in interrupt context, and
host initiated resume code will directly signal resume, wait 20ms and then
move the port to U0.
These two codepaths can race, if we are in the middle of a host initated
resume, while sleeping for 20ms, we may handle a port event and find the
port in resume state. The port event handling code will assume the resume
was device initiated and set the resume flag and timestamp.
Root hub code will however not catch the port in resume state again as the
host initated resume code has already moved the port to U0.
The resume flag and timestamp will remain set for this port preventing port
from suspending again (LPM setting port to U3)
Fix this for now by always clearing the device initated resume parameters
once port is in U0
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function ep_ring_is_processing() checks the dequeue pointer
in endpoint context to know whether an endpoint is busy with
processing TRBs. This is not correct since dequeue pointer
field in an endpoint context is only valid when the endpoint
is in Halted or Stopped states. This buggy code causes audio
noise when playing sound with USB headset connected to host
controllers which support CFC (one of xhci 1.1 features).
This patch should exist in stable kernel since v4.3.
Reported-and-tested-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Reported-by: coverity (CID 1324138)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later. Renaming tmp_dev to of_id (like all others do) in the
process.
Reported-by: coverity (CID 1324135)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
This patch is to support load and unload gadget driver in full OTG mode.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Jiada Wang <jiada_wang@mentor.com>
Cc: <stable@vger.kernel.org> #v4.0+
Since the ci->role will be set after the host role start is complete, there
will be nobody cared irq during start host if usb irq enabled. This error
can be reproduced on i.mx6 sololite EVK board by:
1. disable otg id irq(IDIE) and disable all real otg properties of usbotg1
in dts.
2. boot up the board with ID cable and usb device connected.
3. echo gadget > /sys/kernel/debug/ci_hdrc.0/role
4. echo host > /sys/kernel/debug/ci_hdrc.0/role
5. irq 212: nobody cared.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Some i.mx platforms need three clocks to let controller work, but
others only need one, refine clock operation to adapt for all
platforms, it fixes a regression found at i.mx27.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+
Following changes that appeared in lk 4.0.0, the gadget udc driver for
some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families)
incorrectly deduced full-speed USB link speed even when the hardware
had negotiated a high-speed link. The fix is to make sure that the
UDPHS Interrupt Enable Register value does not mask the SPEED bit
in the Interrupt Status Register.
For a mass storage gadget this problem lead to failures when the host
had a USB 3 port with the xhci_hcd driver. If the host was a USB 2
port using the ehci_hcd driver then the mass storage gadget worked
(but probably at a lower speed than it should have).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> #4.0+
Fixes: 9870d895ad ("usb: atmel_usba_udc: Mask status with enabled irqs")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change the permission of usb_dma parameter so it can
be used for runtime debug without reboot.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.
Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.
At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.
[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are a few changes in musb_h_tx_flush_fifo().
- It has been observed that sometimes (if not always) musb is unable
to flush tx fifo during urb dequeue when disconnect a device. But
it seems to be harmless, since the tx fifo flush is done again in
musb_ep_program() when re-use the hw_ep.
But the WARN() floods the console in the case when multiple tx urbs
are queued, so change it to dev_WARN_ONCE().
- applications could queue up many tx urbs, then the 1ms delay could
causes minutes of delay in device disconnect. So remove it to get
better user experience. The 1ms delay does not help the flushing
anyway.
- cleanup the debug code - related to lastcsr.
----
Note: The tx fifo flush issue has been observed during device disconnect
on AM335x.
To reproduce the issue, ensure tx urb(s) are queued when unplug the usb
device which is connected to AM335x usb host port.
I found using a usb-ethernet device and running iperf (client on AM335x)
has very high chance to trigger the problem.
Better to turn on dev_dbg() in musb_cleanup_urb() with CPPI enabled to
see the issue when aborting the tx channel.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit 734643dfbd ("usb: dwc2: host: add flag to reflect bus
state") we changed dwc2_port_suspend() not to set the lx_state
anymore (instead it sets the new bus_suspended variable). This
introduced a bug where we would fail to detect device insertions if:
1. Plug empty hub into dwc2
2. Plug USB flash drive into the empty hub.
3. Wait a few seconds
4. Unplug USB flash drive
5. Less than 2 seconds after step 4, plug the USB flash drive in again.
The dwc2_hcd_rem_wakeup() function should have been changed to look at
the new bus_suspended variable.
Let's fix it. Since commit b46146d59f ("usb: dwc2: host: resume root
hub on remote wakeup") talks about needing the root hub resumed if the
bus was suspended, we'll include it in our test.
It appears that the "port_l1_change" should only be set to 1 if we were
in DWC2_L1 (the driver currently never sets this), so we'll update the
former "else" case based on this test.
Fixes: 734643dfbd ("usb: dwc2: host: add flag to reflect bus state")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Gregory Herrero <gregory.herrero@intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The comment for ahbcfg for rk3066 parameters (also used for rk3288)
claimed that ahbcfg was INCR16, but it wasn't. Since the bits weren't
shifted properly, the 0x7 ended up being masked and we ended up
programming 0x3 for the HBstLen. Let's set it to INCR16 properly.
As per Wu Liang Feng at Rockchip this may increase transmission
efficiency. I did blackbox tests with writing 0s to a USB-based SD
reader (forcefully capping CPU Freq to try to measure efficiency):
cd /sys/devices/system/cpu/cpu0/cpufreq
echo userspace > scaling_governor
echo 126000 > scaling_setspeed
for i in $(seq 10); do
dd if=/dev/zero of=/dev/sdb bs=1M count=750
done
With the above tests I found that speeds went from ~15MB/s to ~18MB/s.
Note that most other tests I did (including reading from the same USB
reader) didn't show any difference in performance.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Liangfeng Wu <wulf@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The DEVICE_HWI type was added under the faulty assumption that Huawei
devices based on Qualcomm chipsets and firmware use the static USB
interface numbering known from Gobi devices. But this model does
not apply to Huawei devices like the HP branded lt4112 (Huawei me906e).
Huawei firmwares will dynamically assign interface numbers. Functions
are renumbered when the firmware is reconfigured.
Fix by changing the DEVICE_HWI type to use a simplified version
of Huawei's subclass + protocol scheme: Blacklisting known network
interface combinations and assuming the rest are serial.
Reported-and-tested-by: Muri Nicanor <muri+libqmi@immerda.ch>
Tested-by: Martin Hauke <mardnh@gmx.de>
Cc: <stable@vger.kernel.org>
Fixes: e7181d005e ("USB: qcserial: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
otg_dev->extcon was referenced before otg_dev was initialized. Fix.
Cc: <stable@vger.kernel.org> # v4.3
Fixes: a2fd242324 ("usb: phy: omap-otg: Replace deprecated API of extcon")
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a bit of a mess in the order of arguments to the ulpi write
callback. There is
int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)
in drivers/usb/common/ulpi.c;
struct usb_phy_io_ops {
...
int (*write)(struct usb_phy *x, u32 val, u32 reg);
}
in include/linux/usb/phy.h.
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
Fixes: ffb865b1e4 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Honeywell HGI80 is a wireless interface to the evohome connected
thermostat. It uses a TI 3410 USB-serial port.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Also known as Verizon U620L.
The device is modeswitched from 1410:9020 to 1410:9022 by selecting the
4th USB configuration:
$ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4
This configuration provides a ECM interface as well as TTYs ('Enterprise
Mode' according to the U620 Linux integration guide).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
It seems like this device has same vendor and product IDs as G2K
devices, but it has different number of interfaces(4 vs 5) and also
different interface layout which makes it currently unusable:
usbcore: registered new interface driver qcserial
usbserial: USB Serial support registered for Qualcomm USB modem
usb 2-1.2: unknown number of interfaces: 5
lsusb output:
Bus 002 Device 003: ID 05c6:9215 Qualcomm, Inc. Acer Gobi 2000 Wireless
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x05c6 Qualcomm, Inc.
idProduct 0x9215 Acer Gobi 2000 Wireless Modem
bcdDevice 2.32
iManufacturer 1 Quectel
iProduct 2 Quectel LTE Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 209
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Cc: stable <stable@vger.kernel.org>
[johan: rename define and add comment ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Add helper to access line-control register in order to work around a
cp2108 GET_LINE_CTL bug.
cp2108 GET_LINE_CTL returns the 16-bit value with the 2 bytes swapped.
However, SET_LINE_CTL functions properly. When the driver tries to modify
the register, it reads it, modifies some bits and writes back. Because the
read bytes were swapped, this often results in an invalid value to be
written. In turn, this causes cp2108 respond with a stall. The stall
sometimes doesn't clear properly and cp2108 starts responding to following
valid commands also with stalls, effectively failing.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: amend commit message, modify probe error handling ]
Signed-off-by: Johan Hovold <johan@kernel.org>
This change is preparation for implementing a cp2108 bug workaround.
The workaround requires storing some private data. Right now the data is
attached to the USB interface and allocated in the attach() callback.
The bug detection requires USB I/O which is done easier from port_probe()
callback rather than attach(). Since the USB access functions take port
as a parameter, and since the private data is used exclusively by these
functions, it can be allocated in port_probe(). Also, all cp210x devices
have exactly 1 port per USB iterface, so moving private data from the USB
interface to port is trivial.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Flush all device queues at close in order to work around a cp2108 Tx
queue bug.
Occasionally, writing data and immediately closing the port makes cp2108
stop responding. The device has to be unplugged to clear the error.
The failure is induced by shutting down the device while its Tx queue
still has unsent data. This condition is avoided by issuing PURGE command
from the close() callback.
This change is applied to all cp210x devices. Clearing internal queues on
close is generally good.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Sorry for the delay in this patch which was mostly caused by getting the
merger of the mpt2/mpt3sas driver, which was seen as an essential item of
maintenance work to do before the drivers diverge too much. Unfortunately,
this caused a compile failure (detected by linux-next), which then had to be
fixed up and incubated. In addition to the mpt2/3sas rework, there are
updates from pm80xx, lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc
and ufs plus an assortment of changes including some year 2038 issues, a fix
for a remove before detach issue in some drivers and a couple of other minor
issues.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWRnpiAAoJEDeqqVYsXL0MJd0IAIkNP1q/6ksMw/lam2UlbdxN
zFsFOIhGM3xLnBFehbCx7JW3cmybA7WC5jhMjaa1OeJmYHLpwbTzvVwrLs2l/0y1
/S+G0wwxROZfIKj/1EO3oKbSPCu9N3lStxOnmNXt5PSUEzAXrTqSNTtnMf2ZGh7j
bQxTWEJe+66GckgGw4ozTXJHWXqM/Zs/FsYjn2h/WzFhFv8utr7zRSzHMVjcqpLG
TK/Lt03hiTGqiignKrV9W6JzdGTWf2LGIsj/njgR0dxv59cNH8PrHIjZyknSBxgn
lblinsCjxDHWnP4BSfTi9MQG1lEiZiWO3Y6TKkKJTgxZ9M0Eitspc+cLOiJ1mpg=
=HvQf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"Sorry for the delay in this patch which was mostly caused by getting
the merger of the mpt2/mpt3sas driver, which was seen as an essential
item of maintenance work to do before the drivers diverge too much.
Unfortunately, this caused a compile failure (detected by linux-next),
which then had to be fixed up and incubated.
In addition to the mpt2/3sas rework, there are updates from pm80xx,
lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
an assortment of changes including some year 2038 issues, a fix for a
remove before detach issue in some drivers and a couple of other minor
issues"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
mpt3sas: fix inline markers on non inline function declarations
sd: Clear PS bit before Mode Select.
ibmvscsi: set max_lun to 32
ibmvscsi: display default value for max_id, max_lun and max_channel.
mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
mvumi: 64bit value for seconds_since1970
be2iscsi: Fix bogus WARN_ON length check
scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
mpt3sas: Bump mpt3sas driver version to 09.102.00.00
mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
mpt2sas, mpt3sas: Update the driver versions
mpt3sas: setpci reset kernel oops fix
mpt3sas: Added OEM Gen2 PnP ID branding names
mpt3sas: Refcount fw_events and fix unsafe list usage
mpt3sas: Refcount sas_device objects and fix unsafe list usage
mpt3sas: sysfs attribute to report Backup Rail Monitor Status
mpt3sas: Ported WarpDrive product SSS6200 support
mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
mpt3sas: Manage MSI-X vectors according to HBA device type
...
Pull SCSI target updates from Nicholas Bellinger:
"This series contains HCH's changes to absorb configfs attribute
->show() + ->store() function pointer usage from it's original
tree-wide consumers, into common configfs code.
It includes usb-gadget, target w/ drivers, netconsole and ocfs2
changes to realize the improved simplicity, that now renders the
original include/target/configfs_macros.h CPP magic for fabric drivers
and others, unnecessary and obsolete.
And with common code in place, new configfs attributes can be added
easier than ever before.
Note, there are further improvements in-flight from other folks for
v4.5 code in configfs land, plus number of target fixes for post -rc1
code"
In the meantime, a new user of the now-removed old configfs API came in
through the char/misc tree in commit 7bd1d4093c ("stm class: Introduce
an abstraction for System Trace Module devices").
This merge resolution comes from Alexander Shishkin, who updated his stm
class tracing abstraction to account for the removal of the old
show_attribute and store_attribute methods in commit 517982229f
("configfs: remove old API") from this pull. As Alexander says about
that patch:
"There's no need to keep an extra wrapper structure per item and the
awkward show_attribute/store_attribute item ops are no longer needed.
This patch converts policy code to the new api, all the while making
the code quite a bit smaller and easier on the eyes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>"
That patch was folded into the merge so that the tree should be fully
bisectable.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (23 commits)
configfs: remove old API
ocfs2/cluster: use per-attribute show and store methods
ocfs2/cluster: move locking into attribute store methods
netconsole: use per-attribute show and store methods
target: use per-attribute show and store methods
spear13xx_pcie_gadget: use per-attribute show and store methods
dlm: use per-attribute show and store methods
usb-gadget/f_serial: use per-attribute show and store methods
usb-gadget/f_phonet: use per-attribute show and store methods
usb-gadget/f_obex: use per-attribute show and store methods
usb-gadget/f_uac2: use per-attribute show and store methods
usb-gadget/f_uac1: use per-attribute show and store methods
usb-gadget/f_mass_storage: use per-attribute show and store methods
usb-gadget/f_sourcesink: use per-attribute show and store methods
usb-gadget/f_printer: use per-attribute show and store methods
usb-gadget/f_midi: use per-attribute show and store methods
usb-gadget/f_loopback: use per-attribute show and store methods
usb-gadget/ether: use per-attribute show and store methods
usb-gadget/f_acm: use per-attribute show and store methods
usb-gadget/f_hid: use per-attribute show and store methods
...
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Merge second patch-bomb from Andrew Morton:
- most of the rest of MM
- procfs
- lib/ updates
- printk updates
- bitops infrastructure tweaks
- checkpatch updates
- nilfs2 update
- signals
- various other misc bits: coredump, seqfile, kexec, pidns, zlib, ipc,
dma-debug, dma-mapping, ...
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (102 commits)
ipc,msg: drop dst nil validation in copy_msg
include/linux/zutil.h: fix usage example of zlib_adler32()
panic: release stale console lock to always get the logbuf printed out
dma-debug: check nents in dma_sync_sg*
dma-mapping: tidy up dma_parms default handling
pidns: fix set/getpriority and ioprio_set/get in PRIO_USER mode
kexec: use file name as the output message prefix
fs, seqfile: always allow oom killer
seq_file: reuse string_escape_str()
fs/seq_file: use seq_* helpers in seq_hex_dump()
coredump: change zap_threads() and zap_process() to use for_each_thread()
coredump: ensure all coredumping tasks have SIGNAL_GROUP_COREDUMP
signal: remove jffs2_garbage_collect_thread()->allow_signal(SIGCONT)
signal: introduce kernel_signal_stop() to fix jffs2_garbage_collect_thread()
signal: turn dequeue_signal_lock() into kernel_dequeue_signal()
signals: kill block_all_signals() and unblock_all_signals()
nilfs2: fix gcc uninitialized-variable warnings in powerpc build
nilfs2: fix gcc unused-but-set-variable warnings
MAINTAINERS: nilfs2: add header file for tracing
nilfs2: add tracepoints for analyzing reading and writing metadata files
...
1. Rename dequeue_signal_lock() to kernel_dequeue_signal(). This
matches another "for kthreads only" kernel_sigaction() helper.
2. Remove the "tsk" and "mask" arguments, they are always current
and current->blocked. And it is simply wrong if tsk != current.
3. We could also remove the 3rd "siginfo_t *info" arg but it looks
potentially useful. However we can simplify the callers if we
change kernel_dequeue_signal() to accept info => NULL.
4. Remove _irqsave, it is never called from atomic context.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The asm-generic changes for 4.4 are mostly a series from Christoph Hellwig
to clean up various abuses of headers in there. The patch to rename the
io-64-nonatomic-*.h headers caused some conflicts with new users, so I
added a workaround that we can remove in the next merge window.
The only other patch is a warning fix from Marek Vasut
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dQKG
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"The asm-generic changes for 4.4 are mostly a series from Christoph
Hellwig to clean up various abuses of headers in there. The patch to
rename the io-64-nonatomic-*.h headers caused some conflicts with new
users, so I added a workaround that we can remove in the next merge
window.
The only other patch is a warning fix from Marek Vasut"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: temporarily add back asm-generic/io-64-nonatomic*.h
asm-generic: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
gpio-mxc: stop including <asm-generic/bug>
n_tracesink: stop including <asm-generic/bug>
n_tracerouter: stop including <asm-generic/bug>
mlx5: stop including <asm-generic/kmap_types.h>
hifn_795x: stop including <asm-generic/kmap_types.h>
drbd: stop including <asm-generic/kmap_types.h>
move count_zeroes.h out of asm-generic
move io-64-nonatomic*.h out of asm-generic
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sR0p
-----END PGP SIGNATURE-----
Merge tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates, including:
- Lots of improvements at the kABI documentation
- Split of Videobuf2 into a common part and a V4L2 specific one
- Split of the VB2 tracing events into a separate header file
- s5p-mfc got support for Exynos 5433
- v4l2 fixes for 64-bits alignment when running 32 bits userspace
on ARM
- Added support for SDR radio transmitter at core, vivid and hackrf
drivers
- Some y2038 fixups
- Some improvements at V4L2 colorspace support
- saa7164 converted to use the V4L2 core control framework
- several new boards additions, cleanups and fixups
PS: There are two patches for scripts/kernel-doc that are needed by
the documentation patches on Media. Jon is OK on merging those via
my tree"
* tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (146 commits)
[media] c8sectpfe: Remove select on CONFIG_FW_LOADER_USER_HELPER_FALLBACK
[media] DocBook media: update copyright/version numbers
[media] ivtv: Convert to get_user_pages_unlocked()
[media] media/v4l2-ctrls: fix setting autocluster to manual with VIDIOC_S_CTRL
[media] DocBook media: Fix a typo in encoder cmd
[media] DocBook: add SDR specific info to G_MODULATOR / S_MODULATOR
[media] DocBook: add SDR specific info to G_TUNER / S_TUNER
[media] hackrf: do not set human readable name for formats
[media] hackrf: add support for transmitter
[media] hackrf: switch to single function which configures everything
[media] hackrf: add control for RF amplifier
[media] DocBook: add modulator type field
[media] v4l: add type field to v4l2_modulator struct
[media] DocBook: document SDR transmitter
[media] v4l2: add support for SDR transmitter
[media] DocBook: document tuner RF gain control
[media] v4l2: add RF gain control
[media] v4l2: rename V4L2_TUNER_ADC to V4L2_TUNER_SDR
[media] media/vivid-osd: fix info leak in ioctl
[media] media: videobuf2: Move v4l2-specific stuff to videobuf2-v4l2
...
Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6f64ACgkQMUfUDdst+ykf8gCfYPjtHy5hD/TsharaeXROnVgi
W8cAn16xk1Nmnde220MNNpO6zDu65G/1
=kslf
-----END PGP SIGNATURE-----
Merge tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (148 commits)
tty: Use unbound workqueue for all input workers
tty: Abstract tty buffer work
tty: Prevent tty teardown during tty_write_message()
tty: core: Use correct spinlock flavor in tiocspgrp()
tty: Combine SIGTTOU/SIGTTIN handling
serial: amba-pl011: fix incorrect integer size in pl011_fifo_to_tty()
ttyFDC: Fix build problems due to use of module_{init,exit}
tty: remove unneeded return statement
serial: 8250_mid: add support for DMA engine handling from UART MMIO
dmaengine: hsu: remove platform data
dmaengine: hsu: introduce stubs for the exported functions
dmaengine: hsu: make the UART driver in control of selecting this driver
serial: fix mctrl helper functions
serial: 8250_pci: Intel MID UART support to its own driver
serial: fsl_lpuart: add earlycon support
tty: disable unbind for old 74xx based serial/mpsc console port
serial: pl011: Spelling s/clocks-names/clock-names/
n_tty: Remove reader wakeups for TTY_BREAK/TTY_PARITY chars
tty: synclink, fix indentation
serial: at91, fix rs485 properties
...
Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6gVMACgkQMUfUDdst+ynLZgCePfhiDuwriaX7osq90HDu8JOc
pTEAn2dBdw2VMPToUlxccR963YSfgu2A
=mMgp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while"
* tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (233 commits)
USB: core: Codestyle fix in urb.c
usb: misc: usb3503: Use i2c_add_driver helper macro
usb: host: lpc32xx: don't unregister phy device
usb: host: lpc32xx: balance clk enable/disable on removal
usb: host: lpc32xx: fix warnings caused by enabling unprepared clock
uwb: drp: Use setup_timer
uwb: neh: Use setup_timer
uwb: rsv: Use setup_timer
USB: qcserial: add Sierra Wireless MC74xx/EM74xx
usb: chipidea: otg: don't wait vbus drops below BSV when starts host
chipidea: ci_hdrc_pci: use PCI_VDEVICE() instead of PCI_DEVICE()
doc: dt-binding: ci-hdrc-usb2: split vendor specific properties
usb: chipidea: imx: add imx6ul usb support
doc: dt-binding: ci-hdrc-usb2: improve property description
usb: chipidea: imx: add usb support for imx7d
Doc: usb: ci-hdrc-usb2: Add phy-clkgate-delay-us entry
usb: chipidea: Add support for 'phy-clkgate-delay-us' property
usb: chipidea: Use extcon framework for VBUS and ID detect
usb: gadget: net2280: restore ep_cfg after defect7374 workaround
usb: dwc2: host: Fix use after free w/ simultaneous irqs
...
v4.4 kernel development cycle:
Infrastructure:
- Doug Anderson wrote a patch adding an "init" state
different from the "default" state for pin control
state handling in the core framework. This is applied
before the driver's probe() call if defined and takes
precedence over "default". If both are defined, "init"
will be applied *before* probe() and "default" will be
applied *after* probe().
Significant subdriver improvements:
- SH PFC is switched to getting GPIO ranges from the
device tree ranges property on DT platforms.
- Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all
modernized.
- Got rid of SH PFC hardcoded IRQ numbers.
- Allwinner sunxi external interrupt through the "r"
controller.
- Moved the Cygnus driver to use DT-provided GPIO
ranges.
New drivers:
- Atmel PIO4 pin controller for the SAMA4D2 family
New subdrivers:
- Rockchip RK3036 subdriver
- Renesas SH PFC R8A7795 subdriver
- Allwinner sunxi A83T PIO subdriver
- Freescale i.MX7d iomux lpsr subdriver
- Marvell Berlin BG4CT subdriver
- SiRF Atlas 7 step B SoC subdriver
- Intel Broxton SoC subdriver
Apart from this, the usual slew if syntactic and semantic
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0t3B
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.4 kernel
development cycle. Development pace is high in pin control again this
merge window. 28 contributors, 83 patches.
It hits a few sites outside the pin control subsystem:
- Device tree bindings in Documentation (as usual)
- MAINTAINERS
- drivers/base/* for the "init" state handling by Doug Anderson.
This has been ACKed by Greg.
- drivers/usb/renesas_usbhs/rcar2.c, for a dependent Renesas change
in the USB subsystem. This has been ACKed by both Greg and Felipe.
- arch/arm/boot/dts/sama5d2.dtsi - this should ideally have gone
through the ARM SoC tree but ended up here.
This time I am using Geert Uytterhoeven as submaintainer for SH PFC
since the are three-four people working in parallel with new Renesas
ASICs.
Summary of changes:
Infrastructure:
- Doug Anderson wrote a patch adding an "init" state different from
the "default" state for pin control state handling in the core
framework. This is applied before the driver's probe() call if
defined and takes precedence over "default". If both are defined,
"init" will be applied *before* probe() and "default" will be
applied *after* probe().
Significant subdriver improvements:
- SH PFC is switched to getting GPIO ranges from the device tree
ranges property on DT platforms.
- Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all modernized.
- Got rid of SH PFC hardcoded IRQ numbers.
- Allwinner sunxi external interrupt through the "r" controller.
- Moved the Cygnus driver to use DT-provided GPIO ranges.
New drivers:
- Atmel PIO4 pin controller for the SAMA4D2 family
New subdrivers:
- Rockchip RK3036 subdriver
- Renesas SH PFC R8A7795 subdriver
- Allwinner sunxi A83T PIO subdriver
- Freescale i.MX7d iomux lpsr subdriver
- Marvell Berlin BG4CT subdriver
- SiRF Atlas 7 step B SoC subdriver
- Intel Broxton SoC subdriver
Apart from this, the usual slew if syntactic and semantic fixes"
* tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (81 commits)
pinctrl: pinconf: remove needless loop
pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIER
pinctrl: zynq: fix UTF-8 errors
pinctrl: zynq: Initialize early
pinctrl: at91: add missing of_node_put
pinctrl: tegra-xusb: Correct lane mux options
pinctrl: intel: Add Intel Broxton pin controller support
pinctrl: intel: Allow requesting pins which are in ACPI mode as GPIOs
pinctrl: intel: Add support for multiple GPIO chips sharing the interrupt
drivers/pinctrl: Add the concept of an "init" state
pinctrl: uniphier: set input-enable before pin-muxing
pinctrl: cygnus: Add new compatible string for gpio controller driver
pinctrl: cygnus: Remove GPIO to Pinctrl pin mapping from driver
pinctrl: cygnus: Optional DT property to support pin mappings
pinctrl: sunxi: Add irq pinmuxing to sun6i "r" pincontroller
pinctrl: sunxi: Fix irq_of_xlate for the r_pio pinctrl block
pinctrl: sh-pfc: Remove obsolete r8a7778 platform_device_id entry
pinctrl: sh-pfc: Remove obsolete r8a7779 platform_device_id entry
pinctrl: sh-pfc: Stop including <linux/platform_data/gpio-rcar.h>
usb: renesas_usbhs: Remove unneeded #include <linux/platform_data/gpio-rcar.h>
...
This should be our final batch of fixes for 4.3:
- A patch from Sudeep Holla that fixes annotation of wakeup sources properly,
old unused format seems to have spread through copying.
- Two patches from Tony for OMAP. One dealing with MUSB setup problems due to
runtime PM being enabled too early on the parent device. The other fixes
IRQ numbering for OMAP1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jKgB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This should be our final batch of fixes for 4.3:
- A patch from Sudeep Holla that fixes annotation of wakeup sources
properly, old unused format seems to have spread through copying.
- Two patches from Tony for OMAP. One dealing with MUSB setup
problems due to runtime PM being enabled too early on the parent
device. The other fixes IRQ numbering for OMAP1"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
usb: musb: omap2430: Fix regression caused by driver core change
ARM: OMAP1: fix incorrect INT_DMA_LCD
ARM: dts: fix gpio-keys wakeup-source property
Commit ddef08dd00 ("Driver core: wakeup the parent device before trying
probe") started automatically ensuring the parent device is enabled when
the child gets probed.
This however caused a regression for MUSB omap2430 interface as the
runtime PM for the parent device needs the child initialized to access
the MUSB hardware registers.
Let's delay the enabling of PM runtime for the parent until the child
has been properly initialized as suggested in an earlier patch by
Grygorii Strashko <grygorii.strashko@ti.com>.
In addition to delaying pm_runtime_enable, we now also need to make sure
the parent is enabled during omap2430_musb_init. We also want to propagate
an error from omap2430_runtime_resume if struct musb is not initialized.
Note that we use pm_runtime_put_noidle here for both the child and parent
to prevent an extra runtime_suspend/resume cycle.
Let's also add some comments to avoid confusion between the
two different devices.
Fixes: ddef08dd00 ("Driver core: wakeup the parent device before
trying probe")
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Delete braces around single statement block suggested by checkpatch.pl
Signed-off-by: Jonas Hesselmann <jonas.hesselmann@hotmail.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use i2c_add_driver as it will add THIS_MODULE for us.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to unregister the I2C device, which serves as a phy
from host code, this should be done in the correspondent phy driver.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change adds missing clk_disable_unprepare(usb_otg_clk) call, also
the disabled clocks are sorted in order opposite to enabled clocks.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These updates generalise the option DTR/RTS handling so that all
usb-wwan-based drivers can use it. This is specifically needed by some
Sierra modems, which can now all be handled by qcserial again.
Included are also some clean ups of the io_ti firmware handling.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=B3KN
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.4-rc1
These updates generalise the option DTR/RTS handling so that all
usb-wwan-based drivers can use it. This is specifically needed by some
Sierra modems, which can now all be handled by qcserial again.
Included are also some clean ups of the io_ti firmware handling.
Signed-off-by: Johan Hovold <johan@kernel.org>
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWKEKdAAoJEEhZKYFQ1nG7dysH/jmFSatDJvgA7woliRZ7p0H/
elNu6AOjqBnsi23Vp54IOVWYTVIDhLsXxlzEOgO6XXfsI99TqFQIIS2VYSo6xues
Eq5hIxh5n9uue3VMnw9bxYHcFkFG9LDAlyMXecEayAB74UqnQLbo2bRDfnSopaf1
dEOq9mdT8llYbtVww6bVXtL78wgwxVk1gTfISllxgt7DEuYwgT+gQJCDLrmkGPn0
XfiaZWamNmDlQd4z/qqoG65+yNmZZMZQKtugCx4MoiBbHVclRN7j2eNsCZ0y6dsZ
qxs+CazL/IeYCqxRRXl5Fopraer1uJeOPeFgA+lRV6WPhMEe7eg6ojkDp/8Y18Y=
=Dh+g
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB Chipidea updates for v4.4-rc1
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWJoq5AAoJEIaOsuA1yqREOlkQAJTndRGxhcZR5rLzjyRDDags
pYoXJAqaneq5G8BwKY+2AQlPaUr87UEHUOo8pk4S31mdFHlp/d/6YIXLpdlYbEcW
ixGhtxZnUhyvWM0HYGgyoDGQP9YJXy5/MR2lEJhmsqcH/Q0dih5VrDGyJ3BxEboZ
2jXy7iou5fs5nHsR4fpdUH+ER//oKgHopRbbt+mmCwZbRJbuukA0KVDMHO8ix6cy
tG/8zbnv5RY3O4a0lJAST8LNmtpxfF9yUCs83b6muhLgO9GXUGYb+I8DjPJMbwag
klOy8Z1bG5e4ymh6383ZG7wDITf82N5cy5huoyunQHVjYg1L8vDHa9aF72e+yR/3
blb9OYALbKPV072HMwOfH+M9cvcCVDGytbJQIgMot9mjpP6GPhgbGtxb+RWNy2j8
Z2kEaxd3BUXvWiRbvyvn7uQuT/cAF4StrTnQrsbFSt0fKAUkQnGdK7XxYfGGql97
p3u2x2D7YSkurywMWyXjuBsm/mXsImAfTJvoWndyOIHU2PNAzIDM4k9TWaYNNAKA
ilZSuSC/JVnMPEH/J/QpytxMM5wbiGyJOyI4bc4MiAXgCkG3qm8vi0PMZM8x0rEu
q778B+50alg9U7/G75dt0WQP+kqDjn+iUB7i/YUC9sq/Dhlmpp48KvJU+zaco+7I
QsxGXmlgeA7yXX8ywy71
=jPoY
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.4 merge window
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some HW design may use ID pin state to control vbus for otg port,
so before host role start, the vbus is already turned on, in this
case, we do not need wait vbus dropping below BSV.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Fix using the PCI_DEVICE() macro instead of less verbose PCI_VDEVICE().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Add imx6ul usb support.
Signed-off-by: Peter chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Add support for the optional 'phy-clkgate-delay-us' property that is
used to describe the delay time between putting PHY into low power mode
and turning off the PHY clock.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Defect 7374 workaround enables all GPEP as endpoint 0. Restore
endpoint number when defect 7374 workaround is disabled. Otherwise,
check to match USB endpoint number to hardware endpoint number in
net2280_enable() fails.
Cc: <stable@vger.kernel.org> # 4.2
Reported-by: Paul Jones <p.jones@teclyn.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
While plugging / unplugging on a DWC2 host port with "slub_debug=FZPUA"
enabled, I found a crash that was quite obviously a use after free.
It appears that in some cases when we handle the various sub-cases of
HCINT we may end up freeing the QTD. If there is more than one bit set
in HCINT we may then end up continuing to use the QTD, which is bad.
Let's be paranoid and check for this after each sub-case. This should
be safe since we officially have the "hsotg->lock" (it was grabbed in
dwc2_handle_hcd_intr).
The specific crash I found was:
Unable to handle kernel paging request at virtual address 6b6b6b9f
At the time of the crash, the kernel reported:
(dwc2_hc_nak_intr+0x5c/0x198)
(dwc2_handle_hcd_intr+0xa84/0xbf8)
(_dwc2_hcd_irq+0x1c/0x20)
(usb_hcd_irq+0x34/0x48)
Popping into kgdb found that "*qtd" was filled with "0x6b", AKA qtd had
been freed and filled with slub_debug poison.
kgdb gave a little better stack crawl:
0 dwc2_hc_nak_intr (hsotg=hsotg@entry=0xec42e058,
chan=chan@entry=0xec546dc0, chnum=chnum@entry=4,
qtd=qtd@entry=0xec679600) at drivers/usb/dwc2/hcd_intr.c:1237
1 dwc2_hc_n_intr (chnum=4, hsotg=0xec42e058) at
drivers/usb/dwc2/hcd_intr.c:2041
2 dwc2_hc_intr (hsotg=0xec42e058) at drivers/usb/dwc2/hcd_intr.c:2078
3 dwc2_handle_hcd_intr (hsotg=0xec42e058) at
drivers/usb/dwc2/hcd_intr.c:2128
4 _dwc2_hcd_irq (hcd=<optimized out>) at drivers/usb/dwc2/hcd.c:2837
5 usb_hcd_irq (irq=<optimized out>, __hcd=<optimized out>) at
drivers/usb/core/hcd.c:2353
Popping up to frame #1 (dwc2_hc_n_intr) found:
(gdb) print /x hcint
$12 = 0x12
AKA:
#define HCINTMSK_CHHLTD (1 << 1)
#define HCINTMSK_NAK (1 << 4)
Further debugging found that by simulating receiving those two
interrupts at the same time it was trivial to replicate the
use-after-free. See <http://crosreview.com/305712> for a patch and
instructions. This lead to getting the following stack crawl of the
actual free:
0 arch_kgdb_breakpoint () at arch/arm/include/asm/outercache.h:103
1 kgdb_breakpoint () at kernel/debug/debug_core.c:1054
2 dwc2_hcd_qtd_unlink_and_free (hsotg=<optimized out>, qh=<optimized
out>, qtd=0xe4479a00) at drivers/usb/dwc2/hcd.h:488
3 dwc2_deactivate_qh (free_qtd=<optimized out>, qh=0xe5efa280,
hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:671
4 dwc2_release_channel (hsotg=hsotg@entry=0xed424618,
chan=chan@entry=0xed5be000, qtd=<optimized out>,
halt_status=<optimized out>) at drivers/usb/dwc2/hcd_intr.c:742
5 dwc2_halt_channel (hsotg=0xed424618, chan=0xed5be000, qtd=<optimized
out>, halt_status=<optimized out>) at
drivers/usb/dwc2/hcd_intr.c:804
6 dwc2_complete_non_periodic_xfer (chnum=<optimized out>,
halt_status=<optimized out>, qtd=<optimized out>, chan=<optimized
out>, hsotg=<optimized out>) at drivers/usb/dwc2/hcd_intr.c:889
7 dwc2_hc_xfercomp_intr (hsotg=hsotg@entry=0xed424618,
chan=chan@entry=0xed5be000, chnum=chnum@entry=6,
qtd=qtd@entry=0xe4479a00) at drivers/usb/dwc2/hcd_intr.c:1065
8 dwc2_hc_chhltd_intr_dma (qtd=0xe4479a00, chnum=6, chan=0xed5be000,
hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:1823
9 dwc2_hc_chhltd_intr (qtd=0xe4479a00, chnum=6, chan=0xed5be000,
hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:1944
10 dwc2_hc_n_intr (chnum=6, hsotg=0xed424618) at
drivers/usb/dwc2/hcd_intr.c:2052
11 dwc2_hc_intr (hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:2097
12 dwc2_handle_hcd_intr (hsotg=0xed424618) at
drivers/usb/dwc2/hcd_intr.c:2147
13 _dwc2_hcd_irq (hcd=<optimized out>) at drivers/usb/dwc2/hcd.c:2837
14 usb_hcd_irq (irq=<optimized out>, __hcd=<optimized out>) at
drivers/usb/core/hcd.c:2353
Though we could add specific code to handle this case, adding the
general purpose code to check for all cases where qtd might be freed
seemed safer.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
close_wait is no longer needed or provided by the tty core.
Move close_wait to struct gs_port.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch make changes to an if else statement which simplifies the code
allowing to remove a return.
CC: Joe Perches <joe@perches.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We received several reports of systems rebooting and powering on
after an attempted shutdown. Testing showed that setting
XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT
quirk allowed the system to shutdown as expected for LynxPoint-LP
xHCI controllers. Set the quirk back.
Note that the quirk was originally introduced for LynxPoint and
LynxPoint-LP just for this same reason. See:
commit 638298dc66 ("xhci: Fix spurious wakeups after S5 on Haswell")
It was later limited to only concern HP machines as it caused
regression on some machines, see both bug and commit:
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
commit 6962d914f3 ("xhci: Limit the spurious wakeup fix only to HP machines")
Later it was discovered that the powering on after shutdown
was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP
machine suffered from spontaneous resume from S3 (which should
not be related to the SPURIOUS_WAKEUP quirk at all). An attempt
to fix this then removed the SPURIOUS_WAKEUP flag usage completely.
commit b45abacde3 ("xhci: no switching back on non-ULT Haswell")
Current understanding is that LynxPoint-LP (Haswell ULT) machines
need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and
plain Lynxpoint (Haswell) machines may _not_ have the quirk
set otherwise they again will restart.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Oliver Neukum <oneukum@suse.com>
[Added more history to commit message -Mathias]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a host fails to wake up a isochronous SuperSpeed device from U1/U2
in time for a isoch transfer it will generate a "No ping response error"
Host will then move to the next transfer descriptor.
Handle this case in the same way as missed service errors, tag the
current TD as skipped and handle it on the next transfer event.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the difference is big enough between the bytes asked and received
in a bulk transfer we can get a short transfer event pointing to a TRB in
the middle of the TD. We don't want to handle the TD yet as we will anyway
receive a new event for the last TRB in the TD.
Hold off from finishing the TD and removing it from the list until we
receive an event for the last TRB in the TD
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
checkpatch complains about too many leading tabs because the if
statement starts after 6 tabs:
scan_iosoc() -> for() -> while() -> switch() -> if() -> for() -> if()
There is also a goto statement going backwards in case of failure. This
patch creates a new inline function named scan_frame_queue() containing
the last 4 nesting levels, and removes the need of backwards goto,
making the code easier to read. After the patch it becomes:
scan_iosoc() -> for() -> while() -> scan_frame_queue()
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
checkpatch complains about too many leading tabs because the switch
statement starts after 6 tabs.
fill_periodic_buffer() -> for() -> do -> switch() -> if() ->
list_for_each_entry() and finally the last switch().
This patch moves the list_for_each_entry() and the last switch() to a
new function named output_buf_tds_dir(). This change makes the code
easier to read and calm down checkpatch. This patch changes it to:
fill_periodic_buffer() -> for() -> do -> switch() -> if() ->
output_buf_tds_dir()
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch convert the macro speed_char in an inline function. The goal
of this patch is to make the code easier to read.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
msleep under 20ms can result in sleeping up to 20ms, which may not be
intended. Replace msleep(5) by usleep_range(5000, 10000). The range of 5
ms is to reduce the chances of creating an interrupt while reducing the
maximum wait time in 50%.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces:
kmalloc(DBG_SCHED_LIMIT * sizeof(*seen), GFP_ATOMIC)
by:
kmalloc_array(DBG_SCHED_LIMIT, sizeof(*seen), GFP_ATOMIC)
as kmalloc_array() should be used for allocating arrays.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove an else statement after a return to make the code
easier to understand.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove KERN_WARNING from a call to pr_warn().
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix coding style issues reported by checkpatch that do not
change semantics of the code.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fusbh200 and fotg210 are very similar. The initial idea was to consolidate
both drivers but I'm afraid fusbh200 is not being used.
This patch remove the fusbh200 source code, update Kconfig and two
Makefiles.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: John Chiang <john453@faraday-tech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'bDescriptorType' descriptor fields
while the values are #define'd in <linux/usb/ch9.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change avoids DMA error in the cases where dma_mask and
coherent_dma_mask of a 32-bit controller get configured as
DMA_BIT_MASK(64) when running on a 64-bit system.
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provide the methods to let ACPI identify the need to use
xhci-platform. Change the Kconfig files so the
xhci-plat.o file is selectable during kernel config.
This has been tested on an ARM64 machine with platform XHCI, an
x86_64 machine with XHCI, and an x86_64 machine without XHCI.
There were no regressions or error messages on the machines
without platform XHCI.
[dhdang: regenerate the patch over v4.3-rc1 and address new comments]
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci platform driver needs to work on systems that
either only support 64-bit DMA or only support 32-bit DMA.
Attempt to set a coherent dma mask for 64-bit DMA, and
attempt again with 32-bit DMA if that fails.
[dhdang: regenerate the patch over v4.3-rc1 and address new comments]
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Module xhci-pci and xhci-plat-hcd depend on xhci-hcd. Module xhci-hcd
should be put at a place before xhci-pci and xhci-plat-hcd. Otherwise,
xhci_hcd_init() might be executed after other functions in xhci-hcd if
they are all selected to be built in.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The readq() and writeq() helpers are available in the
asm-generic/io-64-nonatomic-hi-lo.h and asm-generic/io-64-nonatomic-lo-hi.h
headers. Replace custom implementation by the generic helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci versions 1.0 and later report the untransferred data remaining in a
TD a bit differently than older hosts.
We used to have separate functions for these, and needed to check host
version before calling the right function.
Now Mediatek host has an additional quirk on how it uses the TD Size
field for remaining data. To prevent yet another function for calculating
remainder we instead want to make one quirk friendly unified function.
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From code inspection, it appears to be unsafe to do a read-modify-write
of PCGCTL in dwc2_port_resume(). Let's make sure the spinlock is held
around this operation.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix musb_platform_get_vbus_status return value in case of platform
implementation is not defined, bringing expected behaviour of
musb_platform_get wrapper. Add musb_vbus_show default method to determine
VBUS status in case platform method is not defined.
Signed-off-by: Roman Alyautdin <ralyautdin@dev.rtsoft.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit e0857ce58e
("usb: gadget: loopback: don't queue requests to bogus endpoints")
Loopback function is not realy working as that commit removed
all looping back logic. After that commit ep-out works like
/dev/null and ep-in works like /dev/zero.
This commit fix this issue by allocating set of out requests
and set of in requests but each out req shares buffer with
one in req:
out_req->buf ---> buf <--- in_req.buf
out_req->context <---> in_req.context
The completion routine simply enqueue the suitable req in
an oposite direction.
Cc: <stable@vger.kernel.org> # 3.18+
Fixes: e0857ce58e
("usb: gadget: loopback: don't queue requests to bogus endpoints")
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Each instance of loopback function may have different qlen
and buflen attributes values. When linking function to
configuration those values had been assigned to global
variables. Linking other instance to config overwrites those
values.
This commit moves those values to f_loopback structure
to avoid overwriting. Now each function has its own instance
of those values.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move function parameters to struct f_sourcesink to make them per instance
instead of having them as global variables. Since we can have multiple
instances of USB function we also want to have separate set of parameters
for each instance.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC2 module on some platforms needs three additional hardware
resources: phy controller, clock and power supply. All of them must be
enabled/activated to properly initialize and operate. This was initially
handled in s3c-hsotg driver, which has been converted to 'gadget' part
of dwc2 driver. Unfortunately, not all of this code got moved to common
platform code, what resulted in accessing DWC2 registers without
enabling low-level hardware resources. This fails for example on Exynos
SoCs. This patch moves all the code for managing those resources to
common platform.c file and provides convenient wrappers for controlling
them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
init_mutex is a leftover from the time, when s3c-hsotg driver did not
implement proper pull up/down control and emulated it by enabling
enabling/disabling usb phy. Proper pull up/down control has been added
by commit 5b9451f8c4 ("usb: dwc2: gadget:
use soft-disconnect udc feature in pullup() method"), so init_muxtex can
be removed now to avoid potential deadlocks with other locks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This also allows to remove the target-specific old configfs macros, and
gets rid of the target_core_fabric_configfs.h header which only had one
function declaration left that could be moved to a better place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
UVC is a little different from other configfs consumers in that it wants
different function and field names from the exposed attribute name, so
it keeps it's local macros to define attributes instead of using the common
ones.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The bulk queue tests are used to show 'best performance' for bulk
transfer, we are often asked this question by users. The implementation
is the same with iso test, that is queue request at interrupt completion,
so we reuse the iso structures, and rename them as common one.
It's result should be very close to IC simulation, in order
to get that, the device side should also need to prepare enough
queue.
We have got the 'best performance' (IN: 41MB, OUT: 39MB) at i.mx platform
(USB2, ARM Cortex A9, stream mode need to enable) with below command:
Host side:
modprobe usbtest
./testusb -a -t 27 -g 64 -s 16384
./testusb -a -t 28 -g 64 -s 16384
Gadget side:
modprobe g_zero loopdefault=1 qlen=64 buflen=16384
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix a duplicate argument warning reported by 0-DAY kernel test
infrastructure in the following patch:
77dbf71 usb: dwc2: host: add disconnect interrupt to host only interrupts
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 8f2c9544ab.
As it breaks g_ether on my Baytrail FFRD8 device. Everything starts out
fine, but after a bit of data has been transferred it just stops
flowing.
Note that I do get a bunch of these "NOHZ: local_softirq_pending 08"
when booting the machine, but I'm not really sure if they're related
to this problem.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 70f3a9caa1.
That commit was causing a lockdep splat with g_ether and that
was interfering with proper functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When handling device GET_DESCRIPTOR, composite gadget driver fills
the bcdUSB field only if the gadget supports USB 3.0. Otherwise
the field is left unfilled.
For consistency, set bcdUSB to 0x0200 for gadgets that don't
support superspeed.
It's correct to use 0x0200 for any setting that doesn't use
superspeed, since USB 2.0 devices can restrict themselves to
full speed only. It is NOT correct to use 0x0210, since BOS
descriptors are handled only if gadget_is_superspeed() is
satisfied, otherwise it results in a stall.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that it is possible to build in multiple dma engines, we can no longer
require MUSB_PIO_ONLY to be set when using the sunxi musb glue.
This patch adds dummy dma hooks to make the musb glue work without
MUSB_PIO_ONLY. This hooks are fake because we do not support dma with
musb on sunxi. The Allwinnner Android kernels have some dma code, but it
is disabled as Allwinner never managed to get it to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Certain Synopsys prototyping PHY boards are not able to meet timings
constraints for LPM. This allows the PHY to meet those timings by
leaving the PHY clock running during suspend.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add platform data and set usb3_lpm_capable and has_lpm_erratum.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the alignment of the PCI device definitions. Also change the hex
digit capitalization of one constant to make it consistent with the
rest of the file and driver.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch allows the dwc3 driver to run on the new Synopsys USB 3.1
IP core, albeit in USB 3.0 mode only.
The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register
interface and programming model as the existing USB 3.0 controller IP
(DWC_usb3). However the GSNPSID and version numbers are different.
Add checking for the new ID to pass driver probe.
Also, since the DWC_usb31 version number is lower in value than the
full GSNPSID of the DWC_usb3 IP, we set the high bit to identify
DWC_usb31 and to ensure the values are higher.
Finally, add a documentation note about the revision numbering scheme.
Any future revision checks (for STARS, workarounds, and new features)
should take into consideration how it applies to both the 3.1/3.0 IP.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds the PCI product ID for the Synopsys USB 3.1 IP core
(DWC_usb31) on a HAPS-based PCI development platform.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This ID is for the Synopsys DWC_usb3 core with AXI interface on PCIe
HAPS platform. This core has the debug registers mapped at a separate
BAR in order to support enhanced hibernation.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This comment is ambiguous since there are other MC73xx devices with
different USB IDs. This USB ID is found in the MC7304 and MC7354.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit d80c0d1418
(excluding the change to MAX_BL_NUM, which has since been removed).
The qcserial driver now enables the SET_CONTROL_LINE_STATE request
so that AT URCs will work. Move these devices back to the qcserial
driver, which is used for other devices in this series that follow
the same layout.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 653cdc13a3.
The qcserial driver now enables the SET_CONTROL_LINE_STATE request
so that AT URCs will work. Move these devices back to the qcserial
driver, which is used for other devices in this series that follow
the same layout.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Three Sierra Wireless modems have been found to require the CDC ACM
SET_CONTROL_LINE_STATE request on the AT port in order to receive
unsolicited response codes, most recently the Dell Wireless 5808e
(which is a re-branded Sierra Wireless EM7355). On the other hand,
the Sierra Wireless MC7710 does not seem to need this request, but
it was found to work either way.
Use this request on the AT port of devices with the Sierra Wireless
layout in the qcserial driver. The other modems that were moved to
the option driver to work around this can now be moved back.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Only the option driver implements the send_setup callback; it uses the
SET_CONTROL_LINE_STATE request in CDC ACM to generate DTR/RTS signals
on the port. This is not driver-specific though and is needed by other
drivers, so move the function to the usb_wwan driver (with formatting
tweaks), and replace the callback pointer with a flag that enables the
request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is a partial, context modified revert of commit e463c6dda8
("USB: option: handle send_setup blacklisting at probe"), which
introduced an unnecessary struct option_private for storing the
interface number used in option_send_setup. Removing this struct
will allow option_send_setup to be generalized for other drivers.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove extra blank lines in the several places where functions were
separated by more than one.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix non-standard formatting in some of the comments.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
[johan: minor fixes ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Move request_firmware from edge_startup to download_fw.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
