When coming out of WoW sleep, check and restart
timers based on TSF2.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The events for patterns 8..15 need to be
cleared on wakeup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handle the user-configured patterns in the range 8..15
when waking up and update wow_status correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The power save state of MCI has to be disabled
when enabling WoW sleep, check this properly.
ar9003_mci_state() doesn't handle MCI_STATE_GET_WLAN_PS_STATE
right now, but this will be done later when proper
support for MCI/PS is added.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several new MCI states have to handled,
add them to the list.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When MCI is enabled and WoW sleep is enabled,
make sure that the RTC keep awake timer is set
with the required value. This is also required
when the AR_WA is programmed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Along with AR9462, AR9565 also has an extra field
in the TX descriptor which needs to be zeroed out
for the keep alive frame. This makes the earlier
REG_WRITE redundant, so it can be removed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If firmware advertises support for TxBF then the
driver has to instruct the firmware accordingly
during runtime. Without this patch connecting to
an AP with beamformer support would yield abysmal
Rx performance.
This has been tested with wmi-tlv and qca6174
while acting as a STA beamformee only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This processes and pushes fw stats to the debug
module (if enabled).
Changing the generic ath10k_wmi_requests_stats()
call to use more stat bits has no effect on older
firmware binaries.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New qca6174 wmi-tlv firmware revisions support
more stat event bits.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The expected parameter is not a single value but a
mask of values.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New qca6174 wmi-tlv firmware supports vdev stats.
This patch adds support for it in the debug
frontend.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't notify host about
self-bss-peer removal until after associated vdev
is deleted. This has been observed with qca6174
WLAN.RM.2.0-00073 firmware.
This patch fixes AP teardown slowdowns and
prevents delays and warnings:
ath10k_pci 0000:00:05.0: failed to remove peer for AP vdev 0: -110
ath10k_pci 0000:00:05.0: removing stale peer xx:xx:xx:xx:xx:xx from vdev_id 0
ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 24
ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 8
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The value was off by one. The error probably has no negative
affect on any upstream firmware, but should be fixed anyway
in case it comes into use in the future.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A bit of general cleanup to make debug messages more useful.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case firmware fails to start the scan, then complete
the start condition and clean up so that driver does not
block on timeout.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
iwlwifi:
* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)
* add support for beamforming
* enable stuck queue detection for iwlmvm
* a few fixes for EBS scan
* fixes for various failure paths
* improvements for TDLS Offchannel
wil6210:
* performance tuning
* some AP features
brcm80211:
* rework some code in SDIO part of the brcmfmac driver related to
suspend/resume that were found doing stress testing
* in PCIe part scheduling of worker thread needed to be relaxed
* minor fixes and exposing firmware revision information to
user-space, ie. ethtool.
mwifiex:
* enhancements for change virtual interface handling
* remove coupling between netdev and FW supported interface
combination, now conversion from any type of supported interface
types to any other type is possible
* DFS support in AP mode
ath9k:
* fix calibration issues on some boards
* Wake-on-WLAN improvements
ath10k:
* add support for qca6174 hardware
* enable RX batching to reduce CPU load
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU1fUoAAoJEG4XJFUm622bnjMH/25f2kyLAJSLJmiIhpEcYlNJ
CJMAYsSTcqhKaMEbx742StUUDH3pa1oV4mQ5csVa2QJIsS90WzPpB1eRnNtQ69Nj
89Zfwa6bbX0TXDgw1Aa28NewPY/3xWpCjI03HBQaMIncToWv3/dzNUr0bEmIuBds
wsr5Y+fy80VKnkoXG7XzGFOqmxxFwNS+UF3M1WNtQ+xcr9rK3/LLxyWFy84S9UIe
4lVOb+df91YFIJeLs28/hfTiRhvV0fWIbupGv8UhuBMho+F0dpLvra+3xksEqALu
4+AzI0j9GjqFfMzbmRBcPcT4Rl37nLmvQ+7XokrFgAYS5zp7OGylOMU3nHyvkuY=
=iL8v
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Major changes:
iwlwifi:
* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)
* add support for beamforming
* enable stuck queue detection for iwlmvm
* a few fixes for EBS scan
* fixes for various failure paths
* improvements for TDLS Offchannel
wil6210:
* performance tuning
* some AP features
brcm80211:
* rework some code in SDIO part of the brcmfmac driver related to
suspend/resume that were found doing stress testing
* in PCIe part scheduling of worker thread needed to be relaxed
* minor fixes and exposing firmware revision information to
user-space, ie. ethtool.
mwifiex:
* enhancements for change virtual interface handling
* remove coupling between netdev and FW supported interface
combination, now conversion from any type of supported interface
types to any other type is possible
* DFS support in AP mode
ath9k:
* fix calibration issues on some boards
* Wake-on-WLAN improvements
ath10k:
* add support for qca6174 hardware
* enable RX batching to reduce CPU load
Conflicts:
drivers/net/wireless/rtlwifi/pci.c
Conflict resolution is to get rid of the 'end' label and keep
the rest.
Signed-off-by: David S. Miller <davem@davemloft.net>
The relay_close() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.
The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.
This patch partially reverts the commit 1846ac3dbe ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().
I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.
Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Fixes: 1846ac3dbe ("ath5k: Use usleep_range where possible")
Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the transmit rate for the keep-alive frames
as 1M/CCK when the current channel is in the
2GHz band.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chips in the AR9003 family have a second TSF, which
needs to be cleared when putting the card to
sleep.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setting the required configuration in the PCIE
WorkAround register needs to be done after all the
WoW parameters have been set.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch addresses several issues with the
ath9k_hw_wow_enable() routine:
* The usage of set/clr variables is removed. Writing
the required values to registers is cleaner.
* The shift value of 28 for the contention window field
in AR_WOW_PATTERN is incorrect, change it to 27.
* Disabling Keep Alive needs to be done based on the
LINK_CHANGE option. This is done unconditionally now,
fix this.
* The workaround for the D1/D3 issue is required only
for AR9462.
* The bitfield for enabling pattern matching for packets
less than 256 bytes has expanded for new chips, handle
this accordingly.
* General cleanup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the number of user patterns is higher for
newer chips, make sure that this is registered
during initialization.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer chips like WB222, WB335 support more than
8 user-configurable patterns. This patch adds
support for it by setting up the correct HW
registers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJU0NEaAAoJEDBSmw7B7bqr2DAP/3nbk6WB2Lz4Vwi8fh9C4y6X
4ZzN2v7NHaimC+Wpxg3wP2wCdX2VG3ZWwF3yLm6qgVHGnE35RFLxURen1eqNeW77
Yf5gvZ066nCGEQ8l8J6YK9vrLX4qp5c4lyE00bbxpZTA4Qq71SgTg+rmGC1be8uX
vacfaLwfDWffuOOnjBAPfanj7f4AQaUEY2uN1WkBFC7iEeOtPcWVkHAFVIeGjJfQ
vfgQJcwOjgWjYbwZdQQi7Aj+k1Yzda4pg1yEWn3CkZ8zyeCYGs1gk2ovoBgPgXBP
yT9ypIdFsN242VJvy7nkFnCKA8mhKyltMQ1Xjs0Q9lAxWdaq9U+iqt5cUn4jxVIG
T9Vi3PCbx/nVOqcfR81dBTQ3uDU5AyosPsmh2YTxi5lpRBrsjNY2FtaKE0sm2Om3
wRiSPOdPrXBeEnU0KssI9e6euXgS4JQV78Naq85OWZDd2yZ1fT5U2fi8y4drRGlz
rucbbobdVhQch5L4FStPz1uW5pNuJrhekXeZIE8MruTNg2A2oBAK3ApO7hxn68sE
RnbAnkxVLwgedC9042JF5eiS1PDIU46w4e782j/+XskVKMEakqd23iJycx3tmgHZ
cxDi/qKZ2RCE74YsT61o/9ErSVPvCfNPL3+CVov918jidQQg2WHfKm/jFlIxHIxk
4wBP7p2VGlENMgw/R8GJ
=wOaR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-02-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3.2 revision has a different target BMI
version so it wasn't recognized by ath10k (despite
the chip_id rev being on the supported list
already).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce an optional log level configuration for the existing debugfs fw_dbglog file. It
allows users to configure the desired log level for firmware dbglog messages.
To configure log level as WARN:
echo 0xffffffff 2 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
The values are:
VERBOSE 0
INFO 1
WARN 2
ERR 3
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Otherwise ath10k will just checksum everything even if it did not
go through the TCP/IP stack (for example bridged frames). In the worst
case this could mean recreating the checksum for incorrect data.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The command logic shouldn't really care about
arvif structure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ath10k driver sets wrong default key idx that results in
sending unicast frames with multicast key.
The reason for this behavior is that cached broadcast key
is installed for station MAC address on association. After
dot1x completes, unicast key is installed for station
MAC address. Default key idx is set to broadcast key id when
driver tries to send broadcast frame. This causes firmware
to use broadcast key id to transmit unicast frames to stations.
Used TX_USAGE flag to set default key for stations.
Added callback for setting unicast default idx which will be
invoked on every default key idx configuration.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current implementation depends on msm-bus driver which
is not merged into mainline kernel therefore
this code is removed
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Print (at debug level) all cipher and AKM suites
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Print Tx descriptors
Print ring index for all Tx related messages
Sort prefixes: Tx for transmit, TxC for completion, added "D"
for descriptor related prints
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use spinlock, this should not impact Tx as lock is always free
except for de-allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Non-cacheable Tx descriptor for the last fragment of
multi-fragment frame used to be written back twice.
Refactor code to always write non-cacheable descriptor
only once
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the Tx, work around used to force destination index 0
to be used. This is no more necessary, as firmware supports
multiple destinations
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the maximum number of configurable patterns
is chip-specific, use the HW capability instead
of a fixed value for checking if a free pattern
slot is available.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These macros are applicable to pre-AR9003 chips
and the addresses are different for the AR9003
family. Since they are unused anyway, remove them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the number of patterns that can be configured in
the HW is higher for newer chips, store the chip-specific
value in ath9k_hw_wow.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be used to hold the WOW state in
ath9k_hw.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to allocate a new structure and
free it for every user pattern, instead use local
variables.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be used to force WOW for cards that
are not present in the supported PCI ID list.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Printing the value of the wakeup status is sufficient.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The various variables tracking bmiss interrupts
are not really used anywhere except in a debug
message. Remove them since they have no functional
purpose.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch makes sure that valid WOW triggers
are present before trying to suspend the device.
Also, introduce and use ATH_OP_WOW_ENABLED to
bypass PCI suspend and clear it in resume().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Registering the card as a wakeup source needs to
be done once, during initialization. When the WOW
configuration changes, the card's status as wakeup
source needs to be changed too and this is done
via the set_wakeup() callback. Also, make sure
the device is removed properly using ath9k_deinit_wow().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If CONFIG_ATH9K_CHANNEL_CONTEXT is enabled, check whether
multiple contexts are active and if so, return 1 without
enabling WOW since we don't support it in this case.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If multiple interfaces are active or there is no
associated station interface, bail out early and
return 1 so that mac80211 can proceed with the normal
suspend routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WOW capability is registered with mac80211 only when
the device has the ability to wakeup, so there is no
need to check in the suspend() routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not try to cancel work instances and ANI when
the device is not present or WOW triggers are
not configured. Bail out early and use ath_err()
for such error conditions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enabling WOW based on the chip is incorrect since
it needs to be done for specific sub-devices which
have proper platform support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During drv_start/drv_stop stress testing in ARM platform,
sometimes target is taking more that 5ms to wake up. Similar
behaviour also noted during driver load and unload iterations.
On such cases, the wakup duration lies between 5-6ms. Hence
increasing pci wakup timeout 10ms to be more safer. With this
changes, able to complete power down/up >100 iterations without
any issues.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable the MCS8 and MCS9 support for 2.4G band, it will
use these data rate with other devices having the same
capability.
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware revisions providing sta keepalive service
have it enabled by default.
mac80211 already does idle connection polling so
it makes no sense to duplicate this in ath10k.
mac80211 wouldn't even know of the offloaded
keepalive NullFunc frames.
This prevents sending out some extraneous frames
on the air.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 has STA keepalive
service available. The service can provide
automatic idle connection polling via NullFunc
frames to AP when acting as a client.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 supports this.
This should fix issues related to multi-vif WMM.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 supports this.
This will be used soon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 already requests WMM per vif but firmware
wasn't able to handle this until now. However new
wmi-tlv firmware for qca6174 is capable of this.
This prepares per-vif WMM param setup.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On some AR955x/QCA953x boards, noise floor calibration
gets stuck and the cause is a hardware/BB issue. To fix
this, peak detect calibration in the HW is disabled
and is done in the driver instead. There a few differences
with the calibration routine for older chips like
AR9331.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The value is different for PCOEM cards and AR955x/AR953x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The LNA gain setting override needs to be done
only for AR9330 and PCOEM chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be used if we need to apply register settings
for all PCOEM solutions (in the AR9003 family).
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch disables HW peak detect calibration for
AR955x, since it is problematic on a few boards.
Instead, manual calibration will be done in the
driver.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch disables HW peak detect calibration for
QCA953x, since it is problematic on a few boards.
Instead, manual calibration will be done in the
driver.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Access point require this API to check peer alive status.
Assume peer is alive when it is connected, because
firmware implements keep alive checks and will disconnect
peer if it is not alive.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement Tx status reporting using skb_complete_wifi_ack().
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Interrupt moderation parameters will never be passed as module
parameters. For product, they will be hard-coded after lab testing,
and for debugging, they can be altered via debugfs.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to HW limitation, inter-packet gap timeout max value is 13 usec.
Update of current thresholds from 15 to 13 usec.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tuning rings size for performance optimization.
Increasing Tx ring size, allows buffering more packets for HW, thus
eliminating idle periods which were observed with smaller ring at
high throughput, because HW was fetching packets faster than driver was
filling them into the TX ring. Rx ring was similarly increased to
avoid same problems in Rx.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tx queue was hard-coded to 1000 in ether_setup. Add wil_dev_setup
function which configures tx queue len to chosen default value
after calling ether_setup.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
upon cfg80211_stop_ap, a graceful AP shutdown is requested from firmware
followed by firmware reset.
In case graceful request failed, error was returned to cfg80211.
The change is to return success in this scenario, because firmware
reset will anyhow shutdown the AP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
netif_carrier_on indication was too late. In case Rx packet received
before netif_carrier_on indication, upper layers could not send
Tx packet back.
The fix is to indicate netif_carrier_on earlier:
for STA, indicate netif_carrier_on when association starts.
for AP/PCP, indicate netif_carrier_on upon starting AP/PCP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
ath9k and ath9k_htc use the variable name "led_blink" to indicate
whether the module parameter "blink" is on. This name is easy to
conflict with other variables, and has caused a compiler error found
by kbuild test bot. The compiler error is as following:
drivers/net/wireless/ath/ath9k/ath9k_htc.o:(.data+0x47c): multiple definition of `led_blink'
drivers/net/wireless/ath/ath9k/ath9k.o:(.bss+0x20): first defined here
Fixes: 3a939a6712 ("ath9k_htc: Add a module parameter to disable blink")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hong Xu <hong@topbug.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New wmi-tlv firmware uses HTT 3.0 protocol which
uses TX_FRM command for management frames (instead
of a dedicated command). To support PMF it is
necessary to provide explicit tailroom.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Software encryption was never necessary.
Tested with fw 636 and fw 10.x.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It makes little sense to keep handling irqs if fw
is dead.
This prevents multiple fw register dumps upon
crash on some devices (seen on QCA6174).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only userspace can make an educated decision when
a trigger frame is required so make sure the
autotrigger service is disabled.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 has u-UAPSD
autotrigger service. If it is enabled firmware
generates trigger frames automatically as
configured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The workaround couldn't work correctly because the
802.11 header wasn't properly stripped of QoS Data
bit so it wasn't recognized in the later parts of
tx path as NullFunc frame and ended up in HTT Tx
instead of HTT Mgmt Tx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware supporting beacon templates (i.e. wmi-tlv
for qca6174) doesn't implicitly take dtim period
from the template. Instead it requires vdev param
to be set accordingly.
This fixes dtim period being stuck at 3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT Tx protocol uses arbitrary host assigned ids
too associate with MSDUs when delivering
completions.
Instead of rolling out own id generation scheme
use the tools provided in kernel.
This should have little to no effect on
performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Both 10.2 firmware binaries 10.2-00082-4 and
10.2.4.20 have introduced ABI changes to fw_stats
each. This caused fw_stats to output wrong data.
Define new structures and use them to parse the
statistics correctly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will make it easier to implement fw stats
parsing for firmware 10.2.
This also renames a few structures for
consistency.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA6174 in combination with new wmi-tlv firmware is capable of
multi-channel, beamforming, tdls and other features.
This patch just makes it possible to boot these devices and do some basic stuff
like connect to an AP without encryption. Some things may not work or may be
unreliable. New features will be implemented later. This will be addressed
eventually with future patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA6174 chip has an extra 4 bytes in
rx_ppdu_end structure which is used in htt_rx_desc
and HTT Rx ring offset setup. This is necessary
for correct Rx for QCA6174 (otherwise Rx
descriptors are overwritten and corrupted).
This means QCA988X will have an extra 4 byte
padding in Rx descriptor layout which is harmless.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are some very rare cases with some hardware
configuration that the device doesn't init quickly
enough in which case reading chip_id yielded 0.
This caused driver to subsequently fail to setup
the device.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware and firmware (qca6174 hw3.0+ and fw
266+) are capable of full aggregation rx
reordering. If it's enabled then Rx is handled via
a new, separate htt event.
The rx ring behaviour is changed a little to
support the new rx scheme. These changes shouldn't
affect qca988x performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to share the
ath10k_skb_cb with Rx path. The Rx path doesn't
need to keep any mac80211's data.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions may report this event as
part of their diagnostics.
This avoids `unknown event` warnings and adds
tracing for the event.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions may report this event as
part of their diagnostics.
This avoids `unknown event` warnings and adds
tracing for the event.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath10k driver only supports HW crypto (except for management
frames or so - CMAC needs to be done in software). Make it use
the new IEEE80211_HW_SW_CRYPTO_CONTROL flag to ensure mac80211
doesn't erroneously attempt to use software crypto.
Taking through my tree after Kalle's ACK to avoid breaking the
ath10k driver with the next crypto patches.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Coverity: CID 114932
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This clause is conditioned on htc_hdr != NULL, but it will only be NULL
when that check is reached.
Coverity: CID 114318
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add an option "blink" to enable or disable the LED blink. The default
value is set to 1 so that existing users would not experience any
unexpected changes.
Signed-off-by: Hong Xu <hong@topbug.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, wcn36xx only asks for a TX BA session if it has
already established one for RX. Thus, two wcn36xx devices cannot
do a-mpdu between themselves since they both wait for the other
to go first. Fix this by starting a BA session after a few QoS
data frames have been sent to a STA.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The pdu is part of the buffer descriptor, so it makes
sense that one function would fill both. Also, passing
the whole skb instead of just the header pointer to the
set_tx_data function paves the way for using its fields
for ampdu setup inside set_tx_data().
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dxe lock is missing its initialization, so add it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ctl->skb_lock is never initialized, a fact caught by lockdep.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The DMA engine will reset the valid bit after a descriptor is
complete; any with the valid bit still set may still be in
use by the hardware, so check that before freeing the descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx currently sends an incorrect sequence number into the BA session
setup firmware command: it should be saving or updating the ssn in the
TX_START ampdu_action callback instead of waiting until TX_OPERATIONAL.
However, we can sidestep the issue by letting the hardware generate the
sequence numbers for QoS frames, as is done in prima, so do that.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
bd->tx_comp is a single bit in a bitfield, so assigning
"info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS" only happens
to work because TX_STATUS is defined to BIT(0); if it were
any other bit this assignment would fail.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set up default configuration for the device when we call start.
The defaults come from dumps from the prima driver for the same
hardware.
This fixes transmit A-MPDU; previously only one MPDU would be
sent per A-MPDU due to missing MAX_MPDUS_IN_AMPDU setting.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check if the frame has been completed without any
error and use IEEE80211_TX_STAT_NOACK_TRANSMITTED to
indicate successful transmission of no-ack frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To fix invalid hardware accesses, the commit 872b5d814f ("ath9k: do not
access hardware on IRQs during reset") made the irq handler ignore interrupts
emitted after queueing a hardware reset (which disables the IRQ). This left a
small time window for the IRQ to get re-enabled by the tasklet, which caused
IRQ storms. Instead of returning IRQ_NONE when ATH_OP_HW_RESET is set, disable
the IRQ entirely for the duration of the reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some reason, we made the bandwidth separate flags, which
is rather confusing - a single rate cannot have different
bandwidths at the same time.
Change this to no longer be flags but use a separate field
for the bandwidth ('bw') instead.
While at it, add support for 5 and 10 MHz rates - these are
reported as regular legacy rates with their real bitrate,
but tagged as 5/10 now to make it easier to distinguish them.
In the nl80211 API, the flags are preserved, but the code
now can also clearly only set a single one of the flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds several new PCI IDs for AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable per-packet TPC on AR9002 based chips by default
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add TPC capability to TX descriptor path for AR9002 based chips. Scale
per-packet TX power according to eeprom power bias, power adjustments for
HT40 mode and open loop CCK rates. Cap per-packet TX power according to
TX power per-rate tables
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add TX power per-rate tables for MIMO/legacy modes for AR9002 based chips
in order to cap the maximum TX power value per-rate in the TX descriptor path.
Add TX power adjustments for HT40 mode, open loop CCK rates and eeprom power
bias for AR9280 and later chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the helper to get rid of the file operations per debugfs file. The
device driver data contains struct ieee80211_hw pointer and the
struct ath9k_softc pointer is assigned to ieee80211_hw::priv so it can
be accessed in the seq_file read operation.
Cc: ath9k-devel@lists.ath9k.org
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the Rx reorder mechanism, nothing is done in the interrupt
context, so there is no need to use 'irq' flavors of spinlock.
Rx done in NAPI context (tasklet), other manipulations - in the
thread context.
Having interrupts enabled makes it better for the OS in general.
Besides, if enslaved under bonding, bridge or team driver, Rx
won't work with interrupts disabled.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When establishing BACK, WMI may be handled earlier then Rx, in this case
late Rx will be mis-handled.
Detect early Rx and pass it to the stack, bypass reordering
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sync documentation for the Tx/Rx descriptors with the
firmware/hardware documentation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the reordering block, Ethernet DA was checked for MCAST, this is wrong.
Check instead MCAST indication from 802.11 MAC header. Hardware saves
this into Rx descriptor.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx high threshold interrupt is reported by the hardware in case
when number of not utilized by the HW descriptors in the Rx ring
becomes low.
Introduce module parameter for RX high threshold.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add advanced interrupt moderation support available since "Sparrow B0".
Legacy interrupt moderation used only one counter to moderate tx, rx,
and misc interrupts.
Advanced interrupt moderation bypasses misc, and handles separately tx
and rx interrupts. In addition it has two timers for each interrupt type.
Max burst duration timer which defines how long to postpone interrupt after
first event (receive event for rx and tx complete event for tx), and
interframe timeout which defines how to determine the end of the burst and
issue interrupt even if the first timer still pending.
Capabilities flags in wil_priv is set on initialization according to
HW. The rest of the code checks for advanced interrupt capability bit
in capabilities flags field.
Debugfs is split accordingly: "legacy" interrupt moderation remains
unchanged, new debugs files added for advanced interrupt moderation
support.
Module params are aligned to support advanced interrupt moderation
(tx & rx). When not available (for legacy interrupt moderation) will
use only rx configuration; Tx configuration will be ignored in this
case.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the proper reset follow based on HW capabilities
detection instead of chip ID.
Remove old hw ID mechanism which was used only for reset flow.
Remove support for Marlon A0.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Read relevant information (HW ID for now) once on init
and set capabilities accordingly.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable more flexible control over block ack:
- allow addba for any Tx vring
- allow to specify block ack timeout
- allow to delba for Tx or Rx side of any agreement; with reason
Renamed "addba" entry to "back"; it prints short help when read;
write:
- "add <ringid> <agg_size> <timeout>" to trigger ADDBA
If missing, <timeout> defaults to 0
- "del_tx <ringid> <reason>" to trigger DELBA for Tx side
- "del_rx <CID> <TID> <reason>" to trigger DELBA for Rx side
If missing, <reason> set to "STA_LEAVING" (36)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In STA mode, all Tx should be directed to the same VRING towards the AP.
Thus, look up for the 1-st eligible VRING and use it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil->status used as bitmap; use DECLARE_BITMAP for it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change default to support maximum number of associated
stations to an AP
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When encapsulating 802.3 frames into the 802.11 ones,
8-byte SNAP header added to save ethtype. SNAP is part of
the frame body, thus should be counted in MSDU. So,
MTU = MSDU - SNAP
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When configuring Tx/Rx VRING's, driver need to specify max. MPDU size
It should take into account all overhead introduced by 802.3->208.11
transformation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement delba flow for the responder (Rx) side
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When establishing Block Ack as originator (Tx), control
AMSDU flag when sending ADDBA and update status upon
establishment flow completion. To be used in AMSDU flows
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When printing VRING on debugfs (file "vrings"),
software head & tail indexes were printed in decimal format
while hardware tail in hexadecimal only.
It is not comfortable to compare indexes in different formats;
on the other hand, hexadecimal output useful to see hardware
glitches.
To serve all purposes, print hardware tail in both decimal and
hexadecimal formats.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When disconnecting single STA in AP, it might be that STA
in question is already disconnected. In this case, need to do nothing.
Previously, it was mis-interpreted as "disconnect all"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When printing debugfs for the reorder buffer, include BACK
parameters: window size and timeout
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For manual ADDBA configuration, allow to set desired window size or
disable automatic mechanism.
Introduce module parameter (int) agg_wsize. It can be changed on run time,
will be taken into account on the next connect. Interpretation:
- <0 - disable automatic ADDBA; intended for manual testing through debugfs
- 0 - use automatically calculated window size
- >0 - use this for window size. Clipped by maximum supported by the hardware
with current environment.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon Tx vring creation, initiate BACK establishment
with maximum possible window size.
When establishing secure connection, there is EAPOL data exchange
between connection itself and "data port open", where security
is done and non-EAPOL data may be transferred. It is better to
send EAPOL frames using normal ACK because of firmware considerations.
send ADDBA only is 2 conditions met:
- data port open for the corresponded STA
- vring created
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce BACK establishment procedures; decision logic is not implemented
yet; debugfs entry 'addba' used to manually trigger addba/delba for ringid 0.
debugfs usage:
to establish BACK with agg_wsize 16:
echo 16 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to delete BACK:
echo 0 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to change agg_wsize, one need to delete BACK and establish it anew
ADDBA flow for:
- originator
Tx side (initiator) sends WMI_VRING_BA_EN_CMDID providing
agg_wsize and timeout parameters.
Eventually, it gets event confirming BACK agreement - WMI_BA_STATUS_EVENTID
with negotiated parameters. On this event, update Tx vring data
(struct vring_tx_data) and display BACK parameters on debugfs
- recipient
Rx side (recipient) firmware informs driver about ADDBA with
WMI_RCP_ADDBA_REQ_EVENTID, driver process it in service work
queue wq_service. It adjusts parameters and sends response
with WMI_RCP_ADDBA_RESP_CMDID, and final confirmation provided
by firmware with WMI_ADDBA_RESP_SENT_EVENTID. In case of success,
driver updates Rx BACK reorder buffer.
policy for BACK parameters:
- aggregation size (agg_wsize * MPDUsize)) to not exceed 64Kbytes
DELBA flow for:
- originator
driver decides to terminate BACK, it sends WMI_VRING_BA_DIS_CMDID
and updates struct vring_tx_data associated with vring; ignore
WMI_DELBA_EVENTID.
- recipient
firmware informs driver with WMI_DELBA_EVENTID,
driver deletes correspondent reorder buffer
ADDBA request processing requires sending WMI command, therefore
it is processed in work queue context. Same work queue used as for
connect, it get renamed to wq_service
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To be compliant with the hwmon interface the unit needs to be
millidegree Celsius. Fix that.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a comment for indicating that the ATH10K_SCAN_RUNNING case falls
through to the ATH10K_SCAN_ABORTING case in __ath10k_scan_finish. This
will document that the lack of a break is intentional.
Coverity: CID 1260017
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Originally the explicit fw register dump was added
to wait_for_target_init because interrupts are
masked early during power_up.
Due to some changes in power_up/reset sequences
sometimes when fw crashed ath10k would print the
dump more than once via hif_stop -> warm_reset ->
wait_for_target_init, possibly with different
values each.
Prevent this by doing the explicit fw register
dump only during power_up instead of
wait_for_target_init.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The duty cycle (% of quiet duration) is used to put the device
in quiet mode for the given period. Currently the quiet duration
is wrongly calculated which results in not enabling quiet mode.
Fix the calculation as below
duration = (period * duty cycle) / 100
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions support beacon and probe
response templates instead. This means SWBA events
are no longer delivered for these firmware
revisions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Along beacon template host is expected to setup
p2p information elements as well. Implement wmi
interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions with beacon templates need
probe templates as well because they don't forward
probe requests to host at all.
This is required for new firmware to work with
direct probe requests (notably required by hidden
ssid AP).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions may support setting beacon
template. Implement wmi interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This event is delivered to host by firmware if it
supports beacon templates only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Because of wrong macro check in commit 96bba98393 ("ath10k: fix build error
when hwmon is off"), hwmon never be enabled. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When replenishing Rx buffers driver updates the address of the
buffer and the index of rx buffer in rx ring to the firmware.
Change in order by CPU can cause rx ring corruption. Add memory
barrier before updating rx buffer index to guarantee the order.
This could fix some instances of rx ring corruption due to done
bit in rx attention flag not set.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wait_for_completion_timeout does not return negative values so the tests
for <= 0 are not needed and the case differentiation in the error handling
path unnecessary.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent commit
30c78167bc ("ath10k:
set max_num_vdevs based on wmi op version")
skipped wmi-tlv case and left max_num_vdevs reset.
Make sure it is properly set.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
htt->max_throughput_mbps is not used anywhere.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This per-station debugfs entry helps to send delba in manual mode
for debugging purpose. It accepts tid, initiator and reason code
as inputs.
To send delba,
echo 0 1 37 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This per-station debugfs entry helps to send addba response in
manual mode for debugging purpose. It accepts tid and status code
as input arguments.
To send addba response,
echo 0 25 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba_resp
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This per-station debugfs entry helps to send addba request in manual
mode. Need to pass two configuration parameters (tid, buffer size)
as input.
To send addba,
echo 1 32 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add per station debugfs files when a station is added to mac80211's
station list. This helps to group peer specific debugfs entries
altogether. Right now this callback adds support to test aggregation
procedures (addba/addba_resp/delba) manually.
To enable automatic aggregation in target,
echo 0 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
For manual mode,
echo 1 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI support for sending delba request. This command is used for
debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI support for sending addba response manually. This command
is used for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI support for sending addba request. This command is meant
for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI support for clearing addba response before switching aggregation
mode (auto/manual) for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This feature allows the FW to batch RX indications,
reducing the rate of host interrupt generation, which
in turn reduces CPU load. Currently, this is enabled
only for the 10.2 firmware.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A value of zero indicates that 128B is the maximum
DMA request size for read/writes. But PCI cards based
on AR9880 can support 256B, so enable this for
the 10.2 firmware.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Major changes in ath10k:
* Device tree support
* Major restructuring how to handle different WMI interface versions
* Add WMI TLV interface in preparation for new firmware interface support
* Support new firmware branch 10.2.4
* Add thermal cooling interface
* Add hwmon interface to read temparture from the device
And of course lots of small fixes and cleanups.
kbuild reported a linking error:
ERROR: "devm_hwmon_device_register_with_groups"
[drivers/net/wireless/ath/ath10k/ath10k_core.ko] undefined!
Fix it by returning early and letting the compiler to optimise out the function
call.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is really just duplicating the list of information that's
already available in the nl80211 attribute, so remove the list.
Two small changes are needed:
* remove STATION_INFO_ASSOC_REQ_IES complete, but the length
(assoc_req_ies_len) can be used instead
* add NL80211_STA_INFO_RX_DROP_MISC which exists internally
but not in nl80211 yet
This gets rid of the duplicate maintenance of the two lists.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All of the survey data is (currently) per channel anyway,
so having the word "channel" in the name does nothing. In
the next patch I'll introduce global data to the survey,
where the word "channel" is actually confusing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
do_div() checks the type strictly. 'cycles_t' may be 32-bit under quite
a few architectures (parisc, arm, avr32 ...). So use 'uint64_t' instead
of, the related warning (with allmodconfig under parisc):
CC [M] drivers/net/wireless/ath/wil6210/debugfs.o
In file included from arch/parisc/include/generated/asm/div64.h:1:0,
from include/linux/kernel.h:124,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
drivers/net/wireless/ath/wil6210/debugfs.c: In function ‘wil_vring_debugfs_show’:
include/asm-generic/div64.h:43:28: warning: comparison of distinct pointer types lacks a cast
(void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
^
drivers/net/wireless/ath/wil6210/debugfs.c:107:4: note: in expansion of macro ‘do_div’
do_div(idle, total);
^
In file included from include/uapi/linux/stddef.h:1:0,
from include/linux/stddef.h:4,
from ./include/uapi/linux/posix_types.h:4,
from include/uapi/linux/types.h:13,
from include/linux/types.h:5,
from include/linux/list.h:4,
from include/linux/module.h:9,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/asm-generic/div64.h:44:18: warning: right shift count >= width of type [-Wshift-count-overflow]
if (likely(((n) >> 32) == 0)) { \
^
include/linux/compiler.h:159:40: note: in definition of macro ‘likely’
# define likely(x) __builtin_expect(!!(x), 1)
^
drivers/net/wireless/ath/wil6210/debugfs.c:107:4: note: in expansion of macro ‘do_div’
do_div(idle, total);
^
In file included from arch/parisc/include/generated/asm/div64.h:1:0,
from include/linux/kernel.h:124,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/asm-generic/div64.h:48:22: warning: passing argument 1 of ‘__div64_32’ from incompatible pointer type [-Wincompatible-pointer-types]
__rem = __div64_32(&(n), __base); \
^
drivers/net/wireless/ath/wil6210/debugfs.c:107:4: note: in expansion of macro ‘do_div’
do_div(idle, total);
^
include/asm-generic/div64.h:35:17: note: expected ‘uint64_t * {aka long long unsigned int *}’ but argument is of type ‘cycles_t * {aka long unsigned int *}’
extern uint32_t __div64_32(uint64_t *dividend, uint32_t divisor);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add tpc entry to ath9k debugfs in order to enable/disable hw TPC
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable hw TPC by default on AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The minimum number of pulses per burst on FCC radar type 5 is 1.
Use this number for correct radar detection.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
phymode should use 11b only if NO_OFDM flags is set.
Hence check up channel flag for NO_OFDM and set to
11b.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Assoc peer command contain information about NSS.
When we will get IEEE80211_RC_NSS_CHANGED we should
also send (re) assoc peer command to be sure firmware
will know about it and RC will work correctly.
This was found during code review.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fix TX problem when IBSS used in HT mode.
Before we used 6Mbps all the time for TX direction.
Reported-by: Yeoh Chun-Yeow <yeohchunyeow@gmail.com>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.
Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI command support for reading temperature from the target and
corresponding WMI temperature event handler. The pdev_get_temperature
command is currently supported in 10.2 firmware alone.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Thermal cooling device support is added to control the temperature
by throttling the data transmission for the given duration. Throttling
is done using hw MAC quiet time setting. Period, duration and offset
from TBTT can be set up to quiet the MAC transmits for the required duty
cycle (% of quiet duration). The thermal device allows user to configure
duty cycle.
The quiet params are derived as follows.
period = max(25TU, beacon interval / number of bss)
duration = period * duty cycle / 100
Quiet mode can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI support to send pdev_set_quiet_mode command to target.
This will be used for thermal mitigation purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4 firmware uses bitmask in wmi_resource_config to configure
10.2 firmware features like airtime fairness and rx batch mode instead
of maintaining separete bool entry. This allows new features that can be
configure during init time without breaking backward compatibility.
kvalo: use WMI op version, bump up FW API to 4 to not break older versions of
ath10k
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The internal firmware version doesn't tell much to the user, it's more
informative to use that field to print the wmi op version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ATH10K_FW_FEATURE_WMI_10X should not be used for anymore as that's
now deprecated, instead use wmi op version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to manage firmware differences, we should not use
ATH10K_FW_FEATURE_WMI_10X outside ath10k_core_init_firmware_features(). To
achieve that create new field ar->max_num_vdevs and set it based on wmi op
version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware doesn't allow precise tx rate control so
P2P wasn't entirely spec compliant (it was using
CCK rates in some cases).
The only way to make sure firmware doesn't use CCK
rates is to have a vdev with P2P subtype used for
scanning and tx. This can be done via a special
dedicated P2P device interface support.
This also removes the ancient hack from ath10k in
favor of p2pdev.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per-vif bss_conf.ps should be used to configure
powersave.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting 0 ps timeout to firmware yields very poor
latency and traffic issues. This is the case when
multi-vif is active.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To comply with WMM-PS the device shouldn't wake up
with a NullFunc frame pair when tx-ing. Instead PM
bit on each tx frame should be used.
To make this work correctly firmware needs to be
told to use a different STA PS wake threshold when
u-APSD is enabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions need peer phymode to be
specified as MODE_11B when associating as station
to a 11b AP. Otherwise they can starve other
stations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting fragmentation threshold has not been supported by
any of firmware versions, hence unregister the callback and
remove the function.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Move IEEE80211_TX_CTL_PS_RESPONSE to info->control.flags since
this is used only in the TX path (by ath9k). This frees up
a bit which can be used for other purposes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
Introduce a new wmi interface controls noise floor (NF) calibration
period via debugfs as firmware has introduced it on v10.2.
It allows users to modify frequency of NF calibration in millisecond
and changes RSSI reporting frequency consequently.
Short calibration period will trigger more frequent NF calibration,
so that RSSI reported in receive frames is more realistic.
Till now calibration was done at 30 seconds.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New pdev paramters have been added to firmware 10.2,
hence update wmi interfaces to sync with.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Latest main firmware branch introduced a new WMI
ABI called wmi-tlv. It is not a tlv strictly
speaking but something that resembles it because
it is ordered and may have duplicate id entries.
This prepares ath10k to support new hw.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some functions can be shared across different WMI
ABIs. Make them public so different WMI backends
can use them from different source files in the
future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the 10.x fw branch support was introduced it
became apparent ath10k will need to be able to
deal with different fw ABIs eventually.
The patch creates an abstraction for dealing with
command and event structures across different ABIs
and mostly gets rid of the
ATH10K_FW_FEATURE_WMI_10X flag usage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This splits the actual event parsing into
intermediary structures to facilitate future
support of vastly different ABI WMI backends.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using feature flags, add new 32 bit variable for managing different
WMI versions. This makes it firmware interface tests a bit less convoluted,
especially when we add one more interface.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's easier to manage firmware version differences when we configure them in
one place. Rename ath10k_core_init_max_sta_count() to
ath10k_core_init_firmware_features() and start moving most of the firmware
version ("features") handling to that function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the error handling style preferred in ath10k. Makes it easier to add
ath10k_init_firmware_features() function in the next patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will make it possible to easily support
different hardware with different uart pin
configuration.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to extend the list of
supported hardware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will make it easier to extend and maintain
list of supported hardware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for reading calibration data from Device Tree.
It looks for the calibration data in Device Tree if it can't find it
in a file. If there's no node in Device Tree, ath10k will try to find the
calibration data from OTP.
The node for the calibration data should be defined like this:
pci {
pcie@0 {
reg = <0 0 0 0 0>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
ath10k@0,0 {
reg = <0 0 0 0 0>;
device_type = "pci";
qcom,ath10k-calibration-data = [ 01 02 03 ... ];
};
};
};
Signed-off-by: Toshi Kikuchi <toshik@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reverts commit d32394fae9.
It has been reported to cause problems, Jeremiah writes:
On an Acer C720 laptop if a suspend is performed the screen
freezes, the machine locks up, and according to the indicator
lights it does not enter suspend. A hard reset is required to
get it running again.
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware doesn't place any restrictions on the buffer alignment,
consider this TODO resolved.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If card reset with firmware download executed, followed by reset
with use of firmware from build in flash, firmware download indication
remains in the hardware register.
When running firmware download flow,
the SW download indication is written by the driver to bit 0 in usage_6:
wil_fw_load(), "S(RGF_USER_USAGE_6, 1);"
This register, like all USER RGF, wasn't reset in SW reset flow.
Therefore the driver must clear it on SW reset flow.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_tx_ring, error message printed when tx attempted
while vring has no space to accommodate all fragments of frame.
Normally, such situation handled by stopping tx queue.
But, if tx queue is by-passed (like pktgen does), this error
will be triggered at high rate and dmesg will be flooded with
this message. Whole system may become unstable and hang with
no possible recover except power cycle.
Rate-limit it to prevent dmesg flooding.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some compilation environments, result of pointer arithmetic interpreted as int
while in others it is long int. Force conversion to long.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow to configure VRING size for both Rx and Tx via module parameters:
rx_ring_order and tx_ring_order. Parameters are ring size orders, i.e.
ring size calculated as 1 << order.
Defaults for both Tx and Rx are order 9, i.e. size 512
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to obtain physical device through
wil->pdev->dev path, as it is done by this macro.
The same device already stored as wiphy's device, thus
wil_to_dev() returns the same device as wil_to_pcie_dev()
Remove unnecessary macros, this allows to drop dependency
by pci.h in the firmware download code.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scan timeout treated as indication for firmware error;
and should be handled in the same way.
Recovery state machine does not perform as designed because
its state is not updated in case of scan timeout.
Fix is to set recovery state machine into the proper state.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX_HTRSH interrupt is handled in exactly the same manner
as RX_DONE interrupt - fetching accumulated packets from RX
ring. In addition there's a rate limitted warning message.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Propagate reason for the disconnect through the relevant call chains:
- report to cfg80211 reason as reported by the firmware
- provide to the firmware reason as requested by cfg80211
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of killing interrupts during reset when the first one happens,
kill them before issuing the reset.
This fixes an easy to reproduce crash with multiple cards sharing the
same IRQ.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IRQs are suppressed if ah == NULL and ATH_OP_INVALID being set in
common->op_flags. Close a short time window between those two.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware queues are ordered by priority. Use queue index 0 for BK, which
has lower priority than BE.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.
Cc: stable@vger.kernel.org
Reported-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix missing memory deallocation on error paths in wil_write_file_wmi()
and wil_write_file_txmgmt().
Reported-by: Ahmed Tamrawi <ahmedtamrawi@gmail.com>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't bother with fancy arithmetic and just
hardcode the final values.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In theory it was possible to starve the system if
a tx/rx handler could implicitly trigger more
tx/rx pci events.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass the eid argument via skbuff control buffer.
This will make it possible to work with queues of
HTC event buffers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This wasn't used since forever and there are no
plans on using it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The service bitmap can be used to determine
firmware capabilities.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This shouldn't really happen but take into account
the original service bitmap length when mapping
service ids.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dump print uses sizeof() but since service_map
was a mere pointer the dump was too short.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Traces shouldn't modified passed data. This will
make it possible to pass const arguments to
traces.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Increase the rts threshold from the legacy value of 2347 to support higher
threshold limit.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the helper to get rid of the file operations per debugfs file. The
struct ath9k_softc pointer is set as device driver data to be obtained
in the seq_file read operation.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugfs files that are defined in debug.c which are read-only
and using a simple_open as .open file operation have been modified
to use the single_open seq_file API. This simplifies the read
functions defining the file contents.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of peers isn't directly translatable to
the number of stations because ath10k needs to
reserve a few extra peers for special cases like
multi-vif concurrency.
The previous limit was 126 and 15 stations in AP
mode for 10.x and main firmware branches
respectively. The limit is now 128 and 16 which
was the original intention.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The var was supposed to be protected by data_lock
but it wasn't so in all instances. It's actually
not necessary to have a spinlock protected
num_peers so drop it.
All instances of num_peers are already within
conf_mutex sections so use that.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents warning spamming if peer creation
fails during sta_state in some cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add mem_val debugfs file for dumping the firmware (target) memory and also for
writing to the memory. The firmware memory is accessed through one file which
uses position of the file as the firmware memory address. For example, with dd
use skip parameter for the address.
Beucase target memory width is 32 bits it's strongly recommended to use
blocksize divisable with 4 when using this interface. For example, when using
dd use bs=4 to set the block size to 4 and remember to divide both count and
skip values with four.
To read 4 kB chunk from address 0x400000:
dd if=mem_value bs=4 count=1024 skip=1048576 | xxd -g1
To write value 0x01020304 to address 0x400400:
echo 0x01020304 | xxd -r | dd of=mem_value bs=4 seek=1048832
To read 4 KB chunk of memory and then write back after edit:
dd if=mem_value of=tmp.bin bs=4 count=1024 skip=1048576
emacs tmp.bin
dd if=tmp.bin of=mem_value bs=4 count=1024 seek=1048576
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Debugfs files reg_addr and reg_val are used for reading and writing to the
firmware (target) registers. reg_addr contains the address to be accessed,
which also needs to be set first, and reg_value is when used for reading and
writing the actual value in ASCII.
To read a value from the firmware register 0x100000:
# echo 0x100000 > reg_addr
# cat reg_value
0x00100000:0x000002d3
To write value 0x2400 to address 0x100000:
# echo 0x100000 > reg_addr
# echo 0x2400 > reg_value
#
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_tx_wep_key_work() acquires conf_mutex, so
cancelling it when conf_mutex is already taken
in ath10k_remove_interface() is incorrect, so
move it outside the lock.
Snippet from the lockdep report:
kernel: ======================================================
kernel: [ INFO: possible circular locking dependency detected ]
kernel: 3.18.0-rc5-wl-debug #34 Tainted: G O
kernel: -------------------------------------------------------
kernel: hostapd/451 is trying to acquire lock:
kernel: ((&arvif->wep_key_work)){+.+...}, at: [<ffffffff810872d5>] flush_work+0x5/0x290
kernel: but task is already holding lock:
kernel: (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa0b99f00>] ath10k_remove_interface+0x40/0x290 [ath10k_core]
kernel: which lock already depends on the new lock.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
peer->keys needs to be protected by data_lock
since it is also accessed from the WMI path.
Both install() and clear() routines for peer
keys modify the key contents, so use the data_lock
to avoid races.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When static keys are used in shared WEP, when a
station is associated, message 3 is sent with an
encrypted payload. But, for subsequent
authentications that are triggered without a
deauth, the auth frame is decrypted by the HW.
To handle this, check if the WEP keys have already
been set for the peer and if so, mark the
frame as decrypted. This scenario can happen
when a station changes its default TX key and initiates
a new authentication sequence.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't seem to deilver
management frames with FCS error via WMI so narrow
down the HTT rule to not drop corrupted management
frames.
This basically increases number of frames ath10k
reports while sniffing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When mac80211 requests driver to cancel a hw roc
the driver must not call the expired() callback or
else roc will fail in some cases depending on how
things get scheduled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With P2P concurrency requested hw roc duration
time can be very small. Some firmware revisions
refuse scan requests with too small channel dwell
time.
This prevents messages like, e.g. with connected
STA vif and performing P2P Find:
ath10k_pci 0000:00:05.0: failed to switch to channel for roc scan
ieee80211 phy3: failed to start next HW ROC (-110)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions don't need peer creation
when doing offchannel tx. Earlier revisions would
queue and never release frames without a peer.
This prevent new firmware revisions from stopping
replenishing wmi-htc tx credits and improves
reliability of offchannel tx which would sometimes
silently fail.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Comment was out-of-date. The headroom is no longer
necessary because HTT Tx fragment list is stored
in dma pool item associated with each sk_buff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When re-associating a station, the nss was set back to
maximum value even if user had configured small number
of tx chains. So, pay attention to user's config in
this case as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It appears it takes more than just setting the
hardware's chainmask to make things work well. Without
this patch, a vdev would only use 1x1 rates when chainmask
was set to 0x3.
Setting the 'nss' (number of spatial streams) on the vdev
helps the firmware's rate-control algorithm work properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add TPC capability to TX descriptor path. Cap per-packet TX power according to
TX power per-rate tables. Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add TX power per-rate tables for different MIMO modes (e.g STBC) in order to
cap the maximum TX power value per-rate in the TX descriptor path.
Cap TX power for self generated frames (ACK, RTS/CTS).
Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For FCC and JP, in one of the radar patterns, PPB and PRF seems to be
interchanged leading to frequent incorrect radar detections.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are not many of these messages producted by the
firmware, but they are generally fairly useful, so make it easy to print them
with a separate debug level.
kvalo: fix commit log, rename debug level
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are better ways to get the kernel information, use the
utsname and omit the version code entirely since it's duplicate.
The version magic is rather useless anyway
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
- Use config symbol defined in the driver instead of arch specific one for
conditional compilation.
- Rename the ATHEROS_AR231X config symbol to ATH25.
- Fix include (ar231x_platform.h -> ath25_platform.h).
- Some of AR231x SoCs (e.g. AR2315) have PCI bus support, so remove !PCI
dependency, which block AHB support build.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8248/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 093ec3c533.
AHB bus code has been removed, since we did not have support Atheros
AR231x SoC, required for building the AHB version of ath5k. Now that
support WiSoC chips added we can restore functionality back.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8247/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJUbghkAAoJEDBSmw7B7bqroosP/RABYXUMua+k3Ccq7T4eU4jV
AEO2p2gt5nHBzEl1NCJtdUTJkZ6ftT7ehvAkV2zboB0FBoAoBTbZ8YDtcBBiWaY6
wJ5TYuOl6LFo7csAxWxpCzUxW3M+iq26itpyW9Zt9WWxP4QLSNPFyXEXV3SEh45n
HcDW9A0SE+mgdaTQ2LEMBJ5XWxG/Ic7i9Xn6Py3o4x7NsTB4EqFNOD0WXcPCq7M0
H8xlsIYIBYoGNMsV/2Nu7CEgcSXfDLqWcs9uPHQMCvWPjx/vIoEyOgTwJlE9bQHh
2tloc1LBP6XKQ6g2bJ/pBaQVnZGugcOJhD6KUq3ckNm9qIP1ZtRmJslH4V6pUSCS
eGl3TcAKSSE4BWIa7AaETWXeoH4X68dO7PM7pnflQRCQLzCJRbDWCdqjBst/AxBT
6hvAFAvExEcWBkNVSTJ2egRk/C9cDFKRaCWQ1h4wX9yvh+8efe1D0DDWLW9a9qv1
LsoGJE72BZdXn2CaQEME+CjTd3fWmn6u729d/c863cq2kspCSOof0QD0X9uWhBUx
BvqtgbQjGZzAvHFcjBd7yRd5hz0aDfLyBL59bq2IBzaU1QmyekNPqzSMSD+5ZlCp
uxEeE5AY2+pcNZV1KRtkvgAByfUgAVd0FHZcVb8SIM6QZ3IhqiOuzxuXtxv6hrYP
V/76B+ath4Sv1IPF56ex
=q4e6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"It has been a while since my last pull request, so we accumulated
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fragmented Rx wasn't reporting everything. With
the reworked Rx code it's very easy to fix it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it more in line with the new Rx path.
It also makes the code more reusable because Rx
descriptor is more accessible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The original fix has been moved into a different
place in the code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This creates a single, common path for MSDU,
A-MSDU and fragmented Rx.
Hopefully this will make it easier to understand
Rx path and make it easier to work with.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make the rx_confused be handled by the rx
indication handlers instead of the buffer popping
function.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since htt_rx_mpdu_status isn't used anymore
(instead attention flags are used) simplify the
loop.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using manual sk_buff linking via ->next
use sk_buff_head. It's more robust, cleaner and
there's plenty of helper functions in kernel
already to manage sk_buff_head.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
currently ath9k_common depends on this components.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, when a roc period expires, the offchannel
timer calls ieee80211_remain_on_channel_expired(), but
the roc state is cleared only when the queued work
to switch to the operating channel gets a chance to run.
This race is a problem because mac80211 can issue a
new roc request in this window. To avoid this, handle
roc completion in the offchannel timer itself.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a GO/STA setup, when we switch to the STA context,
the channel context timer is scheduled with a period of
half the beacon interval. If a beacon is received in
this duration, the timer is adjusted to accommodate
TSF sync done by the HW.
But, if the actual channel switch is delayed for some
reason, we end up rearming the timer every time a new
beacon is received. Avoid this by doing the adjustment
only once.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If for some reason a beacon with a new NoA is
not sent out, then reset the mgd_prepare_tx flag.
Not doing this will result in a situation where
a GO will send a new NoA when it shouldn't.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that pending roc/scan
operations are cancelled properly when a new
context is assigned/unassigned.
The flush_work() call to flush out any scheduled
channel context work is removed, instead, sc->mutex
is dropped to allow any pending work to get a chance
to complete by the channel scheduler. Also, increase
the timeout to allow a switch to an active GO.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a pending roc or scan operation is cancelled,
the offchannel operation is cleared, but the offchannel
state in the main scheduler is not cleared. This causes
problems since an active GO will try to process a stale
offchannel request that was deferred earlier. Fix this
by clearing the state when there is no pending offchannel
(roc/scan) operation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers that control the on-chip thermometer
need to be programmed based on the chainmask that
the solution supports, not the chainmask that is
present in the eeprom.
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.
The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.
Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.
Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the initvals for QCA953x v1.1 and v2.0
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Duplicates have been marked.
* New initvals for 1.1 and 2.0 versions.
* xPA support.
* Fix for low power issue.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In secured mesh, the unicast mgmt frame is encrypted using
the same key that used for encrypting the unicast data frame.
This patch "ath9k_htc_firmware: fix the offset of CCMP header
for mesh data frame" applied to open-ath9k-htc-firmware allows
the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately,
this is not working and we still need CCMP encryption of
transmitted management frames to be done in software.
So this patch allows the software encryption for transmitted
management frame to be done in software but remain the hardware
decryption for received management frame.
This patch is tested with the following hardwares:
- TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
- AR9271 802.11n
and managed to work with peer mesh STA equipped with ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to assign the hw queues for mesh interface. Otherwise,
we are not able to bring up the mesh interface due to the
IEEE80211_INVAL_HW_QUEUE error.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can have here two variants. Add
ATH9K_CMN_DEBUGFS y if ATH9K_CMN_DEBUGFS || ATH9K_HTC_DEBUGFS
wich will add more configurations and testcases. Or remove ATH9K_HTC_DEBUGFS
which need more time to be done.
So, make common-spectral ignore ATH9K_DEBUGFS option for now.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/htc_drv_init.c:56:6: sparse: symbol 'ath9k_htc_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:61:6: sparse: symbol 'ath9k_htc_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:66:19: sparse: symbol 'ath9k_htc_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When channel-context is not enabled, all vifs belong to
the first context, but it is not configured as 'assigned'.
Fix misc debugfs file to print out info for non-assigned
contexts, and also print whether ctx is assigned or not.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo <kvalo@qca.qualcomm.com> says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit that went into 3.17:
ath9k: Summarize hw state per channel context
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
broke multi-vif configuration due to not properly calculating
the bssid mask.
The test case that caught this was:
create wlan0 and sta0-4 (6 total), not sure how much that matters.
associate all 6 (works fine)
disconnect 5 of them, leaving sta0 up
Start trying to bring up the other 5 one at a time. It will
fail, with iw events looking like this (in these logs, several
sta are trying to come up, but symptom is the same with just one)
The patch causing the regression made quite a few changes, but
the part I think caused this particular problem was not
recalculating the bssid mask when adding and removing interfaces.
Re-adding those calls fixes my test case. Fix bad comment
as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix to use v10.2 wmi call for firmware v10.2.
It turned out that peer association function was using
v10.1 wmi call for v10.2 firmware during code review.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch would help bring up wifi interface with default board
data in case of failures in otp download. It is useful for initial
calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For packet log, the transmitted frame 802.11 header alone is sufficient.
Recording entire packet is also consuming lot of disk space. To optimize
this, tx and rx data tracepoints are splitted into header and payload
tracepoints.
To record tx ieee80211 headers
trace-cmd record -e ath10k_tx_hdr
To record complete packets
trace-cmd record -e ath10k_tx_hdr -e ath10k_tx_payload
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
use code provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use values provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some reason it didn't coused obvious problems.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
not sure why.
Initially provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename exports from ath9k_spectral_* to ath9k_cmn_spectral_*
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we should be ready to make this code common.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
last preparation before moving ath9k_spectral_scan_ to spectral.c
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we don't have here any ieee80211_hw dependencies any way.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spectral code mostly depends on ath_hw, not on ath_softc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this will alow us to make ath_softc independent code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and move rfs_chan_spec_scan to this struct. We will need it
for common spectral scan code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Track it per channel context instead of in the softc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the reference clock, which could be 25MHz or 40MHz,
AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550.
But, when a chip reset is done, processing the initvals
sets the register back to the default value.
Fix this by moving the code in ath9k_hw_init_pll() to
ar9003_hw_override_ini(). Also, do this override for AR9531.
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions
-----BEGIN PGP SIGNATURE-----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=6GIj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This relatively large batch of changes is comprised of the
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
Conflicts:
drivers/net/wireless/ath/wil6210/cfg80211.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).
Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.
Update the current users with the new prototype.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Firmware was crashing when we were trying to warm reset it
after suspend. This was due to the fact that target registeres
can be accessed only if the hardware is awaken.
This patch makes sure to awake the device also on the hif up,
not only in case of probe call.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing implementation of reset_resume handler just calls
ath6kl_usb_remove() that deallocates all resources.
It can lead to double free, etc. on disconnect.
The patch removes reset_resume handler,
so usb core could conservatively reset the driver.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases hw recovery was taking an absurdly
long time due to ath10k waiting for things that
would never really complete.
Instead of waiting for inevitable timeouts poke
all completions and wakequeues and check if it's
still worth waiting.
Reading/writing ar->state requires conf_mutex.
Since waiters might be holding it introduce a new
flag CRASH_FLUSH so it's possible to tell waiters
to abort whatever they were waiting for.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now it was possible to simulate soft and
hard fw crashes but it wasn't possible to trigger
an immediately hw restart itself (without the fw
crash).
This can be useful when stress testing hw
restarting stability, e.g. during heavy tx/rx
traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While testing other things I've found that CE
items aren't cleared properly. This could lead to
null dereferences in BMI.
To prevent that make sure CE revoking clears the
nbytes value (which is used as a buffer completion
indication) and memset the entire CE ring data
shared between host and target when
(re)initializing.
Also make sure to check BMI xfer pointer and print
a splat instead of crashing the kernel.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently hif_power_up performs effectively a
reset and hif_stop resets the chip as well so
there's no point in resetting here.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The power up procedure was overly complex due to
warm/cold reset workarounds and issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One of the problems with warm reset I've found is
that it must be guaranteed that copy engine
registers are not being accessed while being
reset. Otherwise in worst case scenario the host
may lock up.
Instead of using sleeps and hoping the device is
operational in some arbitrary timeframes use
firmware indication register.
As a side effect this makes driver
boot/stop/recovery faster.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make ath10k_pci_init_pipes() effectively only
alter shared target-host data.
The per_transfer_context is a host-only thing.
It is necessary to preserve it's contents for a
more robust ring cleanup.
This is required for future warm reset fixes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the inline function instead of directly indexing the array.
This allows some architectures with hardware instructions
for bit reversals to eliminate the array.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible to configure driver using mtu_max module parameter
by setting it to value in range of 68..7920 inclusive.
This is sub-optimal performance-wise in case packet is larger than 1 page.
mtu_max default value is 2228.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of FW error, make it clear (in dmesg) what branch is taken
in the error recovery code.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disconnect flow may be invoked either from upper layer request,
or from event reported by the firmware.
In case of firmware event, driver need to release resources for the station but
not send another disconnect WMI command.
In case of upper layer request, WMI_DISCONNECT_STA_CMDID command need to
be issued for the firmware to perform disconnect on the MAC layer. Eventually,
event is expected to confirm MAC disconnect, but it is better to not wait for
firmware event and release station resources immediately. FW may fail to
report disconnect for various reasons, so one could not rely on event always reported.
Introduce parameter to distinguish 2 cases above to prevent double WMI command
issuing.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As communicated with the firmware & hardware teams
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When interface is down, recovery flow should not be attempted.
Next ndo_open() will trigger target reset, that is FW recovery.
Doing recovery while interface is down cause internal "up", leaving
internal driver state in conflict with network stack. Then, when network
stack will call ndo_open(), kernel oops will be triggered.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce pulse_rssi threshold to 15 in order to improve radar pattern detection
probability on ext channel
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The right shift operation has higher precedence than the mask so we
left shift by "(i * 3)" and then immediately right shift by "(i * 3)"
then we mask. It should be left shift, mask, and then right shift.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices have multiple bands enables in the EEPROM data, even though
they are only calibrated for one. Allow platform data to disable
unsupported bands.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some devices (especially little-endian ones), the flash EEPROM data
has a different endian, which needs to be detected.
Add a flag to the platform data to allow overriding that behavior
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the initial NF calibration less likely to fail.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It can cause inconsistent calibration results or in some cases turn the
radio deaf.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When NF calibration fails, the radio often becomes deaf. The usual
hardware hang checks do not detect this, so it's better to issue a reset
when that happens.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "goto chip_reset" is a bit misleading, because it does not actually
issue a chip reset. Instead it is bypassing processing of other
interrupts and assumes that the tasklet will issue a chip reset.
In the case of RXORN this does not happen, so bypassing processing of
other interrupts will simply allow them to fire again. Even if RXORN
was triggering a reset, it is not critical enough to need the bypass
here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
UB124 is a USB based reference design not supported by ath9k or
ath9k_htc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initvals use up quite a bit of space, and PC-OEM support is
typically not needed on embedded systems
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix a 11b/EVM issue by adjusting
FIR filter coefficients.
* Fix a problem with receiving probe request
frames sent at 11b rate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes RX sensitivity issues with AR9580.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently has a race which can be hit
with this sequence:
* Start a scan operation.
* TX BA is initiated by ieee80211_start_tx_ba_session().
* Driver sets up internal state and calls
ieee80211_start_tx_ba_cb_irqsafe().
* mac80211 adds a packet to sdata->skb_queue with
type IEEE80211_SDATA_QUEUE_AGG_START.
* ieee80211_iface_work() doesn't process the
packet because scan is in progress.
* ADDBA response timer expires and the sta/tid is
torn down.
* Driver receives BA stop notification and calls
ieee80211_stop_tx_ba_cb_irqsafe().
* This is also added to the queue by mac80211.
* Now, scan finishes.
At this point, the queued up packets might be processed
if some other operation schedules the sdata work. Since
the tids have been cleaned up already, warnings are hit.
If this doesn't happen, the packets are left in the queue
until the interface is torn down.
Since initiating a BA session when scan is in progress
leads to flaky connections, especially in MCC mode, we
can drop the TX BA request. This improves connectivity
with legacy clients in MCC mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flush timeout in MCC mode is very small, since
we are constrained by the time slice for each
channel context, but since only the HW queues are
flushed when switching contexts, it is acceptable.
Since the SW queues are also emptied in the mac80211 flush()
callback, a larger duration is needed. Add an override
argument to __ath9k_flush() and set it when flush()
is called in MCC mode. This allows the driver to
drain both the SW and HW queues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using ATH_CHANCTX_EVENT_ASSIGN to abort
a HW scan when a new interface becomes active, use the
mgd_prepare_tx() callback. This allows us to make
sure that the GO's channel becomes operational by
using flush_work().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that a GO interface
sends out a new NoA schedule with 200ms duration
when mgd_prepare_tx() is called.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has to be notified when a RoC period
expires in the driver. In MCC mode, since the
offchannel/RoC timer is set with the requested
duration, ieee80211_remain_on_channel_expired() needs
to be called when the timer expires.
But, currently it is done after we move back to
the operating channel. This is incorrect - fix this
by calling ieee80211_remain_on_channel_expired() when
the RoC timer expires and in ath_roc_complete() when
the RoC request is aborted.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a GO interface is active when we receive a
mgd_prepare_tx() call, then we need to send
out a new NoA before switching to a new context.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since both the arguments need to satisfy
the alignment requirements of ether_addr_copy(),
use memcpy() in cases where there will be no
big performance benefit and make sure that
ether_addr_copy() calls use properly aligned
arguments.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ATH_CHANCTX_EVENT_AUTHORIZED is required to trigger
the MCC scheduler when a station interface becomes
authorized. But, since the driver gets station state
notifications when the current operating mode is AP
too, make sure that we send ATH_CHANCTX_EVENT_AUTHORIZED
only when the interface is in station mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pending frames in the driver can be present
either in the HW queues or SW. ath9k_has_pending_frames()
currently checks for the HW queues first and then
checks if any ACs are queued in the driver.
In MCC mode, we need to check the HW queues alone, since
the SW queues are just marked as 'stopped' - they will
be processed in the next context switch. But since we
don't differentiate this now, mention whether we want
to check if there are frames in the SW queues.
* The flush() callback checks both HW and SW queues.
* The tx_frames_pending() callback does the same.
* The call to __ath9k_flush() in MCC mode checks HW queues alone.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An offchannel operation also needs to have
a flush timeout that doesn't exceed the NoA
absence duration of a GO context, so use
channel_switch_time. The first offchannel
operation is set a flush timeout of 10ms since
channel_switch_time will be zero.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In MCC mode, the duration for a channel context
is half the beacon interval and having a large
flush timeout will adversely affect GO operation,
since the default value of 200ms will overshoot
the advertised NoA absence duration.
The scheduler initiates a channel context switch
only when the slot duration for the current
context expires, so there is no possibility of
having a fixed timeout for flush.
Since the channel_switch_time is added to the
absence duration when the GO sets up the NoA
attribute, this is the maximum time that we
have to flush the TX queues. The duration is very
small, but we don't have a choice in MCC mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The timeout value for flushing the TX queues
is hardcoded at 200ms right now. Use a channel
context-specific value instead to allow adjustments
to the timeout in case MCC is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an active context transitions to inactive
state, the NoA schedule needs to be removed
for the context that has beaconing enabled.
Not doing this will affect p2p clients.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a chip reset is done, all running timers,
tasklets etc. are stopped but the beacon tasklet
is left running. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a HW reset is done, the interrupt tasklet is
disabled before ISRs are disabled in the HW. This
allows a small window where the HW can still generate
interrupts. Since the tasklet is disabled and not killed,
it is not scheduled but deferred for execution at a later
time.
This happens because ATH_OP_HW_RESET is not set when ath_reset()
is called. When the hw_reset_work workqueue is used, this
problem doesn't arise because ATH_OP_HW_RESET is set
and the ISR bails out.
Set ATH_OP_HW_RESET properly in ath_reset() to avoid
this race - all the ath_reset_internal() callers have
been converted to use ath_reset() in the previous patch.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having ath_reset_internal() and ath_reset()
as two separate calls to perform a HW reset, have
one function. This makes sure that the behavior will
be the same at all callsites.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the current operating channel context has
been marked as ATH_CHANCTX_STATE_FORCE_ACTIVE,
do not process beacons that might be received,
since we have to wait for the station to become
authorized.
Also, since the cached TSF value will be zero
initially do not rearm the timer in this
case when a beacon is received, since it results
in spurious values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In MCC mode, currently the decision to enable
the multi-channel state machine is done
based on the association status if one of
the interfaces assigned to a context is in
station mode.
This allows the driver to switch to the other
context before the current station is able to
complete the 4-way handshake in case it is
required and this causes problems.
Instead, enable multi-channel mode when the
station moves to the authorized state. This
disallows an early switch to the other channel.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the sta_add()/sta_remove() callbacks,
use the sta_state() callback since this gives
more fine-grained control.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not overwrite AR_PHY_RADAR_1 most significant byte default value
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rts threshold was being configured instead of
fragmentation threshold.
Keep in mind available firmware binaries don't
seem to support fragmentation anyway so this
doesn't fix fragmentation threshold per se.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When user space requests survey info, it is useful to know which of the survey
data refers to the channel that is currently actively being used. One of the
use cases is getting the current channel noise for status output. Without this
flag you would have to look up the channel separately and then compare it
against the frequency in the survey output in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of defining a completely new tracepoint
use an existing tracepoint class.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fundamentally this was wrong. Tsf is only valid
in last MPDU of a PPDU. This means tsf value was
wrong most of the time during heavy traffic.
Also I don't see much point in exposing a
redundant (and broken) tsf value. Userspace can
already read it from the dumped rx descriptor
buffer.
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Once driver entered the rx_confused state it would
refuse to rx even after firmware is restarted.
Make sure to clear it so that rx works after, e.g.
hw restart or after all interfaces are stopped.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In theory it was possible to drain entire HTT Rx
ring via fragmented Rx leading to Rx lockup.
In practice non-data traffic would always trigger
replenishment via the regular Rx handler.
For correctness sake make sure to replenish the
ring on fragmented Rx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The netbuf pop can return NULL. Make sure to check
for that. It shouldn't happen but better safe than
sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's little point in dropping, e.g. frames with
FCS error early in ath10k.
This simplifies amsdu_allowed() and gets rid of
htt_rx_mpdu_status usage finally.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Treat non-chained and chained popping the same
way. Also this makes netbuf pop fully symmetrical
to (re)filling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tracing function was called before buffers were
unmapped from DMA.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the globally defined ieee80211 values instead
of re-defining them in the driver again.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The rx descriptor variable was no longer used in
the rx handler.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT_RX_IND_MPDU_STATUS_MGMT_CTRL was pretty greedy
and because of that ath10k ended up dropping
Control Frames as well as Null Func frames.
Reported-by: Okhwan Lee <ohlee@mwnl.snu.ac.kr>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases the limit may be the same as reg->power_limit, but the
actual value that the hardware uses is not up to date. In that case, a
wrong value for current tx power is tracked internally.
Fix this by unconditionally updating it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many AP devices do not have the proper regulatory domain programmed in
EEPROM. Instead they expect the software to set the appropriate region.
For these devices, the country code defaults to US, and the driver uses
the US CTL tables as well.
On devices bought in Europe this can lead to tx power being set too high
on the band edges, even if the cfg80211 regdomain is set correctly.
Fix this issue by taking into account the DFS region, but only when the
EEPROM regdomain is set to default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling HW queue control for normal (non-mcc) mode
causes problems with queue management, resulting
in traffic stall. Since it is mainly required for
fairness in MCC mode, disable it for the general case.
Bug: https://dev.openwrt.org/ticket/18164
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling init to reinit ce pipe state would also
re-set all static structure links and setting
(which don't change over driver lifecycle).
Make it so alloc links structures and initializes
static data and init part to setup state
variables and clear stuff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This was the final missing bit to making sure the
device doesn't assert interrupts to host.
This should fix possible race when target crashes
during driver teardown.
This also removes an early warm reset workaround
during pci probing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If MSI isn't configured device ROM program expects
legacy interrupts to be enabled before it can
fully boot. Don't forget to disable legacy
interrupts after that.
While at it re-use the legacy irq enabling helper
instead of calling ath10k_pci_write32().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This simply changes the source for txpower setup.
It does not make ath10k use different txpower
values for different vifs.
This will make it easier to implement chanctx in
ath10k in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using global channel won't work with chanctx. Try
to determine the channel from the information
provided in the wmi event itself alone. This
should be sufficient.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code can be symmetrical so make it so. This
makes it easier to understand and work with.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to reconfigure peer
completely upon reassociation. This will make it
easier to have a more uniform association code
across different modes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to pass bss_conf explicitly as it
is accessible via vif pointer. This requires
slight changes in function prototypes. While at it
clean up listen interval workaround/command.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A frequent request have been to be able to provide calibration data from a
file as some of the AP devices store the calibration data on an MTD partition.
This patchset adds support for that and also makes it easier to add Device Tree
support later on.
The calibration data is found by using the id string provided by dev_name()
using this format:
cal-<bus>-<id>.bin
With PCI the id string contains bus, slot and func values. For example for a
PCI device in bus 2 slot 0, ath10k will try to retrieve a calibration data from
a file:
/lib/firmware/ath10k/cal-pci-0000:02:00.0.bin
The calibration data sequence is:
1. Check with request_firmware() if there's a calibration file
("cal-<bus>-<id>.bin") on the filesystem for this device. If yes, use that. If
not, goto 2
2. Check if otp.bin is able to successfully load the calibration data
from OTP. If yes, use that. If not, goto 3.
4. Print an error message that no calibration data found and stop driver
initialization for this device.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 3a0861fffd ("ath10k: remove ath10k_bus") removed enum ath10k_bus
because it was not used for anything at the time. But now it's needed for for
retrieving the right calibration data file so add it back. Only new addition is
ath10k_bus_str().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to add new parameters for the del_station calls
without having to modify all drivers that use this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on GFP flag given to DMA coherent allocation, the behaviour of
dma_free_coherent is changed. This behavioural diffrence is noticeable
in ARM platform. If DMA memory is allocated with GFP_KERNEL, free
coherent can not be called inside spin lock. This is causing kernel
crash in ARM platforms. Fix this by changing GFP flag to atomic.
This is most likely a regression from commit 64badcb6d6 ("ath10k: workaround
fw beaconing bug").
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville says:
====================
pull request: wireless-next 2014-10-09
Please pull this batch of fixes intended for the 3.18 stream!
Andrea Merello makes rtl818x_pci use a more reasonable transmission
rate for HW generated frames.
Fabian Frederick tweaks some kernel-doc bits to avoid warnings.
Larry Finger corrects a possible unaligned access in the rtlwifi code.
Marek Puzyniak avoids a kernel panic in ath9k_hw_reset.
Sujith Manoharan goes for the hat trick -- he fixes a smatch warning
in the shared ath code, he fixes a crash in ath9k, and he corrects
a sequence number assignment problem in ath9k too.
For ease of merging, I pulled the last bits of the wireless tree as well...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ath9k uses a global counter for all
frames that need to be assigned a sequence number.
QoS-data frames are handled properly since they
have a per-tid counter. But, beacons and other
management frames use the same counter even if
multiple interfaces or contexts are present.
Fix this issue by making the counter per-interface
and using it when mac80211 sets IEEE80211_TX_CTL_ASSIGN_SEQ.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add tracing support to forward management and data frames to
user space for packet inspection.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is required if we take into account possibility to load the driver
from initrd (RAM disk), so in other words: very early in the boot process,
before the file system is visible.
In such case we need to have the firmware files accessible from ram disk too,
and this patch guarantee this.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary to create bssid peer for
bssid. Self-address peer is sufficient.
This prevents some firmware revisions from crashing.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It makes a lot more sense to print these kinds of
problems as a warning instead of a debug.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
hw pointer of ath_hw is not assigned to proper value
in function ath9k_hw_reset what finally causes kernel panic.
This can be solved by proper initialization of ath_hw in
ath9k_init_priv.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a channel context is removed, the hw_queue_base
is set to -1, this will result in a panic because
ath9k_chanctx_stop_queues() can be called on an interface
that is not assigned to any context yet - for example,
when trying to scan.
Fix this issue by setting the hw_queue_base to zero
when a channel context is removed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/main.c:88 ath_printk()
error: we previously assumed 'common->hw' could be null (see line 82)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx info such as msdu_id, frame len, vdev id and tid are reported
to user space by tracepoint. This is useful for collecting tx
statistics.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon the reception of frame, the descriptor status are reported
to user space by tracepoint. This is useful for collecting rx
statistics.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is useful for collecting pktlog statistics of tx, rx
and rate information, so add tracing for the API call.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support to configure packet log filters (tx, rx, rate control)
via debugfs. To disable htt pktlog events set the filters to 0.
ex:
To enable pktlog for all filters
echo 0x1f > /sys/kernel/debug/ieee80211/phy*/ath10k/pktlog_filter
To disable pktlog
echo 0 > /sys/kernel/debug/ieee80211/phy*/ath10k/pktlog_filter
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville says:
====================
pull request: wireless-next 2014-10-03
Please pull tihs batch of updates intended for the 3.18 stream!
For the iwlwifi bits, Emmanuel says:
"I have here a few things that depend on the latest mac80211's changes:
RRM, TPC, Quiet Period etc... Eyal keeps improving our rate control
and we have a new device ID. This last patch should probably have
gone to wireless.git, but at that stage, I preferred to send it to
-next and CC stable."
For (most of) the Atheros bits, Kalle says:
"The only new feature is testmode support from me. Ben added a new method
to crash the firmware with an assert for debug purposes. As usual, we
have lots of smaller fixes from Michal. Matteo fixed a Kconfig
dependency with debugfs. I fixed some warnings recently added to
checkpatch."
For the NFC bits, Samuel says:
"We've had major updates for TI and ST Microelectronics drivers, and a
few NCI related changes.
For TI's trf7970a driver:
- Target mode support for trf7970a
- Suspend/resume support for trf7970a
- DT properties additions to handle different quirks
- A bunch of fixes for smartphone IOP related issues
For ST Microelectronics' ST21NFCA and ST21NFCB drivers:
- ISO15693 support for st21nfcb
- checkpatch and sparse related warning fixes
- Code cleanups and a few minor fixes
Finally, Marvell added ISO15693 support to the NCI stack, together with a
couple of NCI fixes."
For the Bluetooth bits, Johan says:
"This 3.18 pull request replaces the one I did on Monday ("bluetooth-next
2014-09-22", which hasn't been pulled yet). The additions since the last
request are:
- SCO connection fix for devices not supporting eSCO
- Cleanups regarding the SCO establishment logic
- Remove unnecessary return value from logging functions
- Header compression fix for 6lowpan
- Cleanups to the ieee802154/mrf24j40 driver
Here's a copy from previous request that this one replaces:
'
Here are some more patches for 3.18. They include various fixes to the
btusb HCI driver, a fix for LE SMP, as well as adding Jukka to the
MAINTAINERS file for generic 6LoWPAN (as requested by Alexander Aring).
I've held on to this pull request a bit since we were waiting for a SCO
related fix to get sorted out first. However, since the merge window is
getting closer I decided not to wait for it. If we do get the fix sorted
out there'll probably be a second small pull request later this week.
'"
And,
"Unless 3.17 gets delayed this will probably be our last -next pull request for
3.18. We've got:
- New Marvell hardware supportr
- Multicast support for 6lowpan
- Several of 6lowpan fixes & cleanups
- Fix for a (false-positive) lockdep warning in L2CAP
- Minor btusb cleanup"
On top of all that comes the usual sort of updates to ath5k, ath9k,
ath10k, brcmfmac, mwifiex, and wil6210. This time around there are
also a number of rtlwifi updates to enable some new hardware and
to reconcile the in-kernel drivers with some newer releases of the
Realtek vendor drivers. Also of note is some device tree work for
the bcma bus.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are attempting to switch to a new
channel context, the TX queues are flushed, but
the mac80211 queues are not stopped and traffic
can still come down to the driver.
This patch fixes it by stopping the queues
assigned to the current context/vif before
trying to flush.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a full chip reset is done, all the queues
across all VIFs are stopped, but if MCC is enabled,
only the queues of the current context is awakened,
when we complete the reset.
This results in unfairness for the inactive context.
Since frames are queued internally in the driver if
there is a context mismatch, we can awaken all the
queues when coming out of a reset.
The VIF-specific queues are still used in flow control,
to ensure fairness when traffic is high.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used when the queues of a context
needs to be stopped.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the ath9k_chanctx_wake_queues() API so
that we can pass the channel context that needs its
queues to be stopped.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When draining of the TX queues fails, a
full HW reset is done. ath_reset() makes sure
that the queues in mac80211 are restarted,
so there is no need to wake them up again.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_has_tx_pending() can be used to
check if there are pending frames instead
of having duplicate code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Checking for the queue depth outside of
the TX queue lock is incorrect and in this
case, is not required since it is done inside
ath9k_has_pending_frames().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to check if the current
channel context has active ACs queued up
if the TX queue is not empty.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce netdev IOCTLs, to be used by the debug tools.
Allows to read/write single dword value or
memory block, aligned to dword
Different address modes supported:
- BAR offset
- Firmware "linker" address
- target's AHB bus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce manual FW recovery mode. It is activated if module parameter
@no_fw_recovery set to true. May be changed at runtime.
Recovery information provided by new "recovery" debugfs file. It prints:
mode = [auto|manual]
state = [idle|pending|running]
In manual mode, after FW error, recovery won't start automatically. Instead,
after notification to user space, recovery waits in "pending" state, as indicated by the
"recovery" debugfs file. User space tools may perform data collection and allow to
continue recovery by writing "run" to the "recovery" debugfs file.
Alternatively, recovery pending may be canceled by stopping network interface
i.e. 'ifconfig wlan0 down'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can allow more than 32 stations to be supported
without over-running the bitmap.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for reading firmware stats through the ethtool
API. This may be easier for applications to manipulate
compared to parsing a text based debugfs file.
kvalo: remove unneeded ifdefs, call ath10k_debug_fw_stats_request() and added
simple error handling
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add three counters related to firmware crashes or resets.
Usage:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/fw_reset_stats
fw_crash_counter 2
fw_warm_reset_counter 43
fw_cold_reset_counter 0
#
kvalo: split into it's own patch, add debugfs file and add locking
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On AR9003, tx control and tx status are in separate descriptor rings.
Tx duration is extracted from the tx control descriptor data, which
ar9003_hw_proc_txdesc cannot access.
Fix getting the duration by adding a separate callback for it.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
chan_lock is not required for checking if
we are in the middle of a HW reset, so do it
early. This also removes the small window
where the lock is dropped and reacquired.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR934x and newer SoC devices, the layout of the AR_RTC_PLL_CONTROL
register changed. This currently breaks at least 5/10 MHz operation.
AR933x uses the old layout.
It might also have been causing other stability issues because of the
different location of the PLL_BYPASS bit which needs to be set during
PLL clock initialization.
This patch also removes more instances of hardcoded register values in
favor of properly computed ones with the PLL_BYPASS bit added.
Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cycpwr_thr1 value needs to be lower on the extension channel than on
the control channel, similar to how the register settings are programmed
in the initvals.
Also drop the unnecessary check for HT40 - this register can always be
written. This patch has been reported to improve HT40 stability and
throughput in some environments.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 09efc56345
I've received reports that this change is decreasing throughput in some
rare conditions on an AR9280 based device
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR934x rev 3, settin the ad-hoc flag completely messes up hardware
state - beacons get stuck, almost no packets make it out, hardware is
constantly reset.
When leaving out that flag and setting up the hw like in AP mode, TSF
timers won't be automatically synced, but at least the rest works.
AR934x rev 2 and older are not affected by this bug
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If stat data exceeds wmi-htc buffer limits
firmware splits it into many wmi stats update
events which are delivered in a ping-pong fashion
triggered by wmi stats request command.
Since there's only an implicit start-of-data and
no end-of-data indications the driver has to
perform some trickery to get complete stat data.
kvalo: use %zu to fix a compiler warning and fix a typo in a comment
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Stats were requested and processed for each read
call. This caused inconsistent readings.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The parsing function was rather complex. Simplify
by splitting it up into firmware branch specific
implementations.
While at it move the parsing code into wmi.c where
it belongs.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The return values are not used by callers of these functions
so change the functions to return void.
Other miscellanea:
o add __printf verification to wil6210 logging functions
No format/argument mismatches found
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Clearing IEEE80211_TX_CTL_PS_RESPONSE in a frame
that is not in the current context doesn't seem right.
Instead make sure that we don't add such frames
to the UAPSD queue by using a local variable.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason why frames marked with
IEEE80211_TX_CTL_TX_OFFCHAN have to be sent using
the UAPSD queue. Since mac80211 makes sure that
RoC is done before pushing an offchannel frame
to the driver, we can use the normal TX queues
for transmission.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we use IEEE80211_HW_QUEUE_CONTROL now, the
CAB/Offchannel queues are registered as the last
two queues. There is no need to check and reassign
the queues in the TX start()/done() routines.
CAB frames will not reach the tx() callback since
we set IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING and
pull the buffered frames during beacon transmission.
We also don't have a special HW queue for handling
off-channel frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide ethtool support; with support for interrupt coalescing through
get_coalesce/set_coalesce.
Placeholders for begin/complete will be used by runtime PM
to make sure target is powered up while performing ethtool operations
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multiple channel contexts are enabled, a p2p interface
that is assigned to a context will have an address that
is different from the device mac address, which is used
by wpa_s as the p2p device ID.
Certain frames like provision requests use the device address
and these get dropped since ath9k_calculate_summary_state()
iterates over only the active interfaces in a context and the
device address is not used.
Fix this by adding the device mac address to the bssid mask.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the BSS information stored in mac80211 directly
is racy in certain conditions. For example, in a MCC
setup, if the scheduler is switching channels when
a local deauth is issued, calculation of the opmode/bssid
etc. is incorrect. To avoid this, store the bss params
in the driver and use it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville says:
====================
pull request: wireless-next 2014-09-22
Please pull this batch of updates intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
For the bluetooth bits, Johan says:
"Here are some more patches intended for 3.18. Most of them are cleanups
or fixes for SMP. The only exception is a fix for BR/EDR L2CAP fixed
channels which should now work better together with the L2CAP
information request procedure."
For the iwlwifi bits, Emmanuel says:
"I fix here dvm which was broken by my last pull request. Arik
continues to work on TDLS and Luca solved a few issues in CT-Kill. Eyal
keeps digging into rate scaling code, more to come soon. Besides this,
nothing really special here."
Beyond that, there are the usual big batches of updates to ath9k, b43,
mwifiex, and wil6210 as well as a handful of other bits here and there.
Also, rtlwifi gets some btcoexist attention from Larry.
Please let me know if there are problems!
====================
Had to adjust the wil6210 code to comply with Joe Perches's recent
change in net-next to make the netdev_*() routines return void instead
of 'int'.
Signed-off-by: David S. Miller <davem@davemloft.net>
AHB bus support was added in v2.6.38, through commit a0b907ee2a
("ath5k: Add AHB bus support."). That code can only be build if the
Kconfig symbol ATHEROS_AR231X is set. But that symbol has never been
added to the tree. So AHB bus support has always been dead code.
Let's remove all code that depends on ATHEROS_AR231X. If that symbol
ever gets added to the tree the AHB bus support can be re-added too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide calibration data used by the firmware to user space via a debugfs file.
This makes it easier to debug calibration related problems.
Example:
sudo cp /sys/kernel/debug/ieee80211/phy0/ath10k/cal_data 1.cal
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
diag_read() is used for reading from firmware memory via the diagnose window.
First user will be cal_data debugfs file.
To serialise diagnostic window access and make it safe to use while firmware is
running take ce_lock both in ath10k_pci_diag_write_mem() and
ath10k_pci_diag_read_mem(). Because of that all the CE calls had to be changed
to _nolock variants.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The diagnostic window (CE7) uses polling and is not initiliased to retrieve
interrupts so disable interrupts altogether for CE7. Otherwise ath10k crashes
when using the diagnostic window while the firmware is running due to NULL
dereference and polling reads timeout.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to debug the device-target
communication at a very low level.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to debug hex dumps on systems
with more than a single ath10k device.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT version is already printed so print WMI
version as well for consistency.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets rid of the ugly scan structure building
and uses a saner way to do it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make all wmi event functions match the same naming
style, i.e. ath10k_wmi_event_<name>.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make the phyerr structures more compact and easier
to understand. Also add constness.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The logic responsible for processing the event is
no different across different firmware binaries.
The difference that needs to be dealt with is the
ABI of data structures.
The intermediate structure uses __le32 to avoid
extra memory allocations to byteswap
variable-length substructures (i.e. host mem
chunks).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Init functions should be placed at the end of
files in most cases to avoid forward declarations
for static functions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simplify the code by deduplicating structure
definitions and code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The structure is being set up in 2 places.
Deduplicate the code by creating a helper.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This command is not used anymore and most firmware
revisions do not seem to handle it well. Channel
switching is done via vdev restarting.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware reports the number of RF chains so use
that for initialization of supp_{tx,rx}_chainmask
instead of using a macro for 3x3 chips.
This should make tx/rx chainmask reports correct
for chips other than 3x3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't wait for beacon tx
completion before sending another SWBA event. This
could lead to hardware using old (freed) beacon
data in some cases, e.g. tx credit starvation
combined with missed TBTT. This is very very rare.
On non-IOMMU-enabled hosts this could be a
possible security issue because hw could beacon
some random data on the air. On IOMMU-enabled
hosts DMAR faults would occur in most cases and
target device would crash.
Since there are no beacon tx completions (implicit
nor explicit) propagated to host the only
workaround for this is to allocate a DMA-coherent
buffer for a lifetime of a vif and use it for all
beacon tx commands. Worst case for this approach
is some beacons may become corrupted, e.g. garbled
IEs or out-of-date TIM bitmap.
Keep the original beacon-related code as-is in
case future firmware revisions solve this problem
so that the old path can be easily re-enabled with
a fw_feature flag.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ah struct might not have been initialized when
interrupt comes so check for it.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As suggeested by checkpatch:
WARNING: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)
In wmi.c I had to change due to sparse warnings copying of struct wmi_mac_addr
from form &cmd->peer_macaddr.addr to cmd->peer_macaddr.addr. In
ath10k_wmi_set_ap_ps_param() I also added the missing ".addr" to the copy
command.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes it more readable and fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/debug.c:593: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:594: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:595: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:596: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:597: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:599: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:600: WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
ath10k/htc.c:49: WARNING: Possible unnecessary 'out of memory' message
ath10k/htc.c:810: WARNING: Possible unnecessary 'out of memory' message
ath10k/htt.h:1034: CHECK: Please use a blank line after function/struct/union/enum declarations
ath10k/htt_rx.c:135: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/htt_rx.c:173: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/pci.c:633: WARNING: macros should not use a trailing semicolon
ath10k/wmi.c:3594: WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
WARNING: Missing a blank line after declarations
Please note that some of the cases I fixed by moving the variable declarations
to the beginning of the function, which is the preferred style in ath10k.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable pulse detection on extension channel if 40MHz channel width has been set
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This happens when CONFIG_ATH9K_CHANNEL_CONTEXT is
not enabled.
../drivers/net/wireless/ath/ath9k/recv.c: In function ‘ath_rx_ps_beacon’:
../drivers/net/wireless/ath/ath9k/recv.c:553:27: error: ‘struct ath_softc’ has no member named ‘offchannel’
if (sc->cur_chan == &sc->offchannel.chan)
^
../scripts/Makefile.build:257: recipe for target 'drivers/net/wireless/ath/ath9k/recv.o' failed
make[10]: *** [drivers/net/wireless/ath/ath9k/recv.o] Error 1
../scripts/Makefile.build:404: recipe for target 'drivers/net/wireless/ath/ath9k' failed
make[9]: *** [drivers/net/wireless/ath/ath9k] Error 2
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize neighbor linked list used by dynack to compute ACK timeout
as the maximum STA ACK timeout
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable ACK timeout estimation algorithm if set_coverage_class routine has been
called with negative coverage_class parameter. Dynack is automatically disabled
setting valid value for coverage class
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ack_to entry to debugfs in order to dump current ACK timeout value
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set control frame bit in rx filter if dynack processing has been activated
in order to enable ACK frame reception
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add sampling methods for ACK RX timestamp in ath_rx_tasklet() and for TX frame
timestamp in ath_tx_complete_aggr() and in ath_tx_process_buffer(). These
samples will be used in dynack processing for ACK timeout estimation
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not overwrite ACK timeout estimation in ath9k_hw_init_global_settings() if
dynack processing has been enabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ACK timeout estimation algorithm to ath9k Makefile and Kconfig
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add dynamic ACK timeout estimation algorithm based on ACK frame RX timestamp,
TX frame timestamp and frame duration.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Tested-by: Philippe Duchein <wireless-dev@duchein.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add duration field to ath_tx_status in order to report frame duration for each
entry in multi-retry chain. These fields will be used in ACK timeout estimation
algorithm (dynack)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove static keyword and export ath9k_hw_setslottime(),
ath9k_hw_set_ack_timeout() and ath9k_hw_set_cts_timeout() in hw.h.
These methods will be used in ACK timeout estimation algorithm (dynack)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In v3.15 the driver stopped to accept network packets after successful
authentification, which could be worked around by passing the
nohwcrypt=1 module parameter. This was not reproducible by
everyone, and showed random behaviour in some tests.
It was caused by an uninitialized variable introduced
in 4ed1a8d4a2 ("ath9k_htc: use ath9k_cmn_rx_accept") and
used in 341b29b9cd ("ath9k_htc: use ath9k_cmn_rx_skb_postprocess").
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=78581
Fixes: 341b29b9cd ("ath9k_htc: use ath9k_cmn_rx_skb_postprocess")
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign 'primary_sta' to the active primary station
interface after iterating over the list of interfaces.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The opmode is verified to be NL80211_IFTYPE_STATION
before calling ath9k_set_assoc_state().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When switching offchannel, BSS related information
in the HW has to be reset to default values. Add a routine
to do this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In MCC mode, the TSF of a context needs to be
adjusted only if it is GO/AP.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The next_tbtt variable in the scheduler is needed only
for GO/AP mode operation and is always read from the
NEXT_TBTT_TIMER in the HW. There is no need to store
the timestamp for received beacons.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When interfaces of different types are present
in a context and an offchannel request is received
on a STA interface, we end up trying to process
beacons received when we are offchannel. This hits
the below warning since offchannel will not have proper
beacon parameters.
Fix this by not processing beacons received when we
are offchannel.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 0 at ../drivers/net/wireless/ath/ath9k/recv.c:552 ath_rx_tasklet+0xf8f/0x1020 [ath9k]()
CPU: 1 PID: 0 Comm: swapper/1 Tainted: G O 3.17.0-rc4-wl-debug #16
Hardware name: LENOVO 28427ZQ/INVALID, BIOS 6JET58WW (1.16 ) 09/17/2009
0000000000000000 15916787056abba3 ffff88013b603d08 ffffffff8156af94
ffff88013b603d50 ffff88013b603d40 ffffffff81070dbd ffff8800a84bb300
ffff8800b05db358 ffff8800a84cc578 ffff8800a84bb300 ffff8800b05daa40
Call Trace:
<IRQ> [<ffffffff8156af94>] dump_stack+0x4d/0x6f
[<ffffffff81070dbd>] warn_slowpath_common+0x7d/0xa0
[<ffffffff81070e3c>] warn_slowpath_fmt+0x5c/0x80
[<ffffffff81572143>] ? _raw_spin_lock_irqsave+0x83/0xa0
[<ffffffffa09d04a6>] ? ath_rx_tasklet+0x9f6/0x1020 [ath9k]
[<ffffffffa09d0a3f>] ath_rx_tasklet+0xf8f/0x1020 [ath9k]
[<ffffffffa09cd4f4>] ath9k_tasklet+0xf4/0x310 [ath9k]
[<ffffffff81075a97>] tasklet_action+0xe7/0xf0
[<ffffffff8107508a>] __do_softirq+0x12a/0x340
[<ffffffff8107544e>] irq_exit+0x9e/0xc0
[<ffffffff81575e56>] do_IRQ+0x56/0xe0
[<ffffffff81573c72>] common_interrupt+0x72/0x72
<EOI> [<ffffffff81421037>] ? cpuidle_enter_state+0x67/0x1a0
[<ffffffff81421257>] cpuidle_enter+0x17/0x20
[<ffffffff810b3ebe>] cpu_startup_entry+0x3ce/0x420
[<ffffffff81048563>] start_secondary+0x233/0x2c0
---[ end trace f15c3e33ba78d840 ]---
------------[ cut here ]------------
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move ath9k_hw_set_radar_params() in ath9k_hw_reset() in order to avoid
AR_PHY_RADAR registers are overwritten after hw reset
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed.
-----BEGIN PGP SIGNATURE-----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=OPIp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
Conflicts:
net/mac80211/iface.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function may return an -ENODEV if debugfs is
disabled in kernel. This should originally be
guarded by ath10k's Kconfig but it still makes
sense to check for the non-NULL errno return
value.
Reported-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.1 firmware does not have an official way to
cause assert on purpose, but it can be done with
carefully crafted WMI command. This is a different
kind of crash from the 'hard' crash, which is
a bad memory dereference.
Different crashes decode in different manners, so
this will help the crash-report testing as well as
offer better ways to test firmware failure and
recovery.
kvalo: move the wmi command creation to debug.c, modify
the info print
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add testmode interface for starting and using UTF firmware which is used to run
factory tests. This is implemented by adding new state ATH10K_STATE_UTF and user
space can enable this state with ATH10K_TM_CMD_UTF_START command. To go back to
normal mode user space can send ATH10K_TM_CMD_UTF_STOP.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The NoA duration for a GO is half the beacon interval
and a concurrent context like a STA can be active only
for that duration, before switching back to the GO's
operating channel.
Currently, when multiple beacons are missed, the dwell
time for the STA context is extended to improve the
chances of receiving a beacon. But the NoA is not updated
and this will cause problems since the GO is offline
for a period that is longer than the advertised duration.
Fix this by ensuring that the NoA is updated first before
extending the time slot for the STA context. Also make
sure that non-periodic NoA is used for a one-time, longer
absence period.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the NoA duration is the maximum time the GO interface
can be offline, it needs to include the time take to
switch channels in the HW.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clearing the offchannel duration value in the
scheduler unconditionally breaks NoA when
multiple contexts are active and an offchannel
request is deferred, for example, in a scan run.
Fix this by clearing the duration only if there
is no pending offchannel request.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* The index has to incremented only when advertising
a new NoA schedule.
* Switch to non-periodic NoA when starting a scan operation
and multiple channel contexts are active.
* Make sure that periodic NoA is advertised again when
scan ends. Since the offchannel timer moves the offchannel
state to IDLE after the GO operating channel becomes
active, use a flag "force_noa_update" to update the
NoA contents.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multi-channel mode, an offchannel request will
be deferred if both contexts are active. The duration
of the offchannel operation is calculated but is
not stored in the scheduler state. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When interface stopped while running intensive Rx traffic, the following oops
observed:
[89846.734683] Call trace:
[89846.737117] [<ffffffc00083aa64>] dev_gro_receive+0xac/0x358
[89846.742674] [<ffffffc00083ae94>] napi_gro_receive+0x24/0xa4
[89846.748251] [<ffffffbffc1c2f88>] $x+0xec/0x1f8 [wil6210] wil_netif_rx_any
[89846.753547] [<ffffffbffc1c4830>] $x+0x34/0x54 [wil6210] wil_release_reorder_frame
[89846.758755] [<ffffffbffc1c48ac>] wil_release_reorder_frames+0x5c/0x78 [wil6210]
[89846.766044] [<ffffffbffc1c4bf8>] wil_tid_ampdu_rx_free+0x20/0x48 [wil6210]
[89846.772901] [<ffffffbffc1bedc8>] $x+0x190/0x1e8 [wil6210]
[89846.778285] [<ffffffbffc1c0ed4>] wmi_event_worker+0x230/0x2f8 [wil6210]
[89846.784865] [<ffffffc0000b0bc8>] process_one_work+0x278/0x3fc
[89846.790591] [<ffffffc0000b1218>] worker_thread+0x200/0x330
[89846.796060] [<ffffffc0000b6664>] kthread+0xac/0xb8
[89846.800836] Code: b940c661 f9406a62 8b010041 f9400026 (f8636882)
[89846.807008] ---[ end trace d6fdc17cd27d18f6 ]---
Reason is the following: when removing Rx vring
(wil_netdev_ops.ndo_stop -> wil_stop -> wil_down -> __wil_down -> wil_rx_fini),
Rx interrupt occurs. It trigger Rx NAPI, calling wil_rx_handle() that reaps
(already cleaned) buffer, causing skb referring to garbage memory being set into reorder buffer.
Then, network stack trying to access this buffer and fails.
Prevent Rx NAPI from being scheduled if device going to stop. Bit wil_status_napi_en reflects
NAPI enablement state, check it when triggering Rx NAPI.
Testing shows that check for wil_status_napi_en sometimes gets negative, and new error message
get printed - in this case kernel oops would be observed. Original oops is no more reproducible.
This change requires also changes in the AP flows.
Properly enable/disable NAPI for the AP. Make sure Rx VRING is disabled
when resetting target.
For this, promote __wil_up() and __wil_down() to the module scope, and use it
in the relevant flows.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To better reflect real action performed, rename:
s/wil6210_disable_irq/wil_mask_irq/
s/wil6210_enable_irq/wil_unmask_irq/
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expose firmware limit for the max_scan_ie_len;
also do actually set IE's for the probe request
max_scan_ie_len used to be 0, this blocks scan requests with non-zero IE's
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
re-use of wmi_ready for both FW ready event and for wmi_call was causing
false "FW not ready" indication in case wmi_call() was invoked while reset
took place.
add wmi_call completion variable instead of re-using wmi_ready.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HW supports upto 2304 packet size on the air.
HW is responsible for adding (Tx) or removing (Rx) the following headers:
802.11 hdr: 26B
SNAP: 8B
CRC: 4B
Security (optional): 24B
HW adds max 62B to the payload passed from driver. It means driver can use
max packet size of 2304-62 = 2242B
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows updating IEs (e.g. from hostapd) when AP is already started
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver is sending connect request IEs to FW only for secure connection and
ignores them for non-secure connection.
This is fixed by always sending the IEs to FW upon connect request
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While handling Rx packet, BACK event arrives and frees tid_ampdu_rx array.
This causes kernel panic while accessing already freed spinlock
The fix is to remove tid_ampdu_rx[]'s spinlock and instead use single
sta's spinlock to guard the whole tid_ampdu_rx array.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WMI event received when driver not ready to accept it, the printed error
message is misleading and hints that HW is stuck. Modify the error message
to make it clearer
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This race condition was causing double free of tid_ampdu_rx structures
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When CONFIG_DYNAMIC_DEBUG is not defined, print_hex_dump_debug
is mapped directly to print_hex_dump which might cause
printout to exist all the time
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver disabled PCI master before making sure HW is idle.
This caused memory corruption in case HW access system memory after
PCI master got disabled.
The fix is to change uninit sequence. Make sure FW/HW is idle before
disabling PCI
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After setting interrupt handler, driver enabled interrupts.
This caused stale (old) HW interrupts to fire before driver is
fully initialized.
The fix is to enable interrupts only when driver is fully initialized
and after FW/HW reset (to prevent any stale interrupts)
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
added misc printouts in some init/uninit functions for better traceability
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New module (wil_platform) for handling platform specific tasks
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- parentheses, indentation, typos
- seq_puts() instead of seq_printf() with single argument
- sizeof(var) vs. sizeof(type)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Log worker thread start/stop; as well as every handler invocation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when connecting, print some info about BSS
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware download implemented but is still experimental feature;
flag controlling it added, no_fw_load. It is true by default,
use no_fw_load=N to activate feature.
Reset flows also got some adjustment for the fw download to work
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 09ebb81092.
ath9k_hw_set_sta_beacon_timers() configures AR_TIM_PERIOD with
the beacon interval. Before this commit, the sleepduration was
never greater than the beacon interval. But now, the behavior
has changed. For example, with an AP that uses a beacon interval of 100:
ath: phy9: next beacon 61128704
ath: phy9: beacon period 204800
ath: phy9: DTIM period 204800
If the sleepduration is calculated based on the listen time, then
the bmiss threshold should also be changed since the HW would
be in sleep state for a longer time, but that is not done currently.
To avoid configuring a higher beacon interval based on the sleepduration,
revert to the original behavior. Power consumption is not a
problem since PS is disabled in ath9k anyway.
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new static_smps / dynamic_smps feature bits
instead of mac80211-internal hw flags.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATH10K_DEBUGFS must depend on DEBUG_FS, otherwise
ath10k will generate an invalid pointer on module load.
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On 32bit systems the bitmap was too small and it
was overwritten partially by the stat completion
structure. This was visible with 10.2 firmware
only due to it using a few of the last service
ids.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After merging the wireless-next tree, today's linux-next build (powerpc
allyesconfig) failed like this:
drivers/net/wireless/ath/ath5k/debug.c: In function 'open_file_eeprom':
drivers/net/wireless/ath/ath5k/debug.c:933:2: error: implicit declaration of function 'vmalloc' [-Werror=implicit-function-declaration]
buf = vmalloc(eesize);
^
drivers/net/wireless/ath/ath5k/debug.c:933:6: warning: assignment makes pointer from integer without a cast
buf = vmalloc(eesize);
^
drivers/net/wireless/ath/ath5k/debug.c:960:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(buf);
^
Caused by commit db906eb210 ("ath5k: added debugfs file for dumping
eeprom"). Also reported by Guenter Roeck.
I have used Geert Uytterhoeven's suggested fix of including vmalloc.h
and so added this patch for today:
From: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Mon, 8 Sep 2014 18:39:23 +1000
Subject: [PATCH] ath5k: fix debugfs addition
Reported-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scanning is curently broken when two channel contexts
are active. For example in a P2P-GO/STA setup, the
offchannel timer allows HZ / 10 to elapse before initiating
a switch to the next scan channel from the current operating
channel, which in this case would be the P2P-GO context.
But, the channel context timer might decide to switch
to the STA context when an SWBA comes early and a beacon
is sent out. Since pending offchannel requests are processed
in EVENT_BEACON_PREPARE, this causes inconsistent scanning.
Fix this by making sure that a context switch happens
before processing the pending offchannel request. This
also makes sure that active channel contexts will always
have higher priority than offchannel operations and the
scan sequence looks like this:
p2p-go, sta, p2p-go, offchannel, p2p-go, sta, p2p-go, offchannel,.....
The oper-channel is p2p-go, so the STA context has to
switch to p2p-go again before switching offchannel.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multiple channel contexts are active, an offchannel
request will not be handled immediately, but will be
queued to be handled later. But, currently, the channel definition
is not copied to the local offchannel state. This
breaks operation like scanning when MCC is active.
Fix this by storing the offchannel parameters properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the interface count is maintained globally,
but this causes problems in RX filter calculation.
Make the interface count a per-channel-context variable
to fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maintain the RX filter on a per-channel-context
basis and not globally. Not doing so was resulting
in incorrect filter calculation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ATH9K_RX_FILTER_COMP_BAR is used to receive BAR
completion frames and is set if the current channel
is HT. When channel contexts are enabled, instead of using
the mac80211 helpers, check if the current channel
definition is HT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since ath_startrecv() doesn't return an error value,
cleanup the callsites.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If multiple channel contexts are active, then the opmode
can be different in each context. Since the RX filter is
calculated in ath_startrecv() before switching to the
new opmode, the wrong filters are chosen.
Fix this by calling ath9k_calculate_summary_state() before
the RX module is started.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since CTWindow can be used for improving discoverability,
fill this field in the NoA Attribute properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, different units are used for handling
sc->offchannel.duration. In scan mode, it contains jiffies and in RoC
mode, milliseconds is used. This causes confusion since in
ath_chanctx_switch(), TU_TO_USEC is used to determine the offchannel
duration, resulting in incorrect values. Fix this by using jiffies in
both modes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The start time field in the NoA attribute needs to be
updated based on the TSF timer when an absence notification
is sent by the P2P GO. When two channel contexts are active,
continuous, cyclic NoA is announced by setting the count value to 255,
but the start time is updated only once, for one beacon and
the same value is sent in all subsequent beacons, even
though the timestamp keeps moving.
Fix this by removing the check for 'periodic_noa_duration'
and assign the interface's start_time/duration values directly
when there is more than one active context.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a station interface is already assigned to a context
and is active and a second interface of type AP is added,
then beaconing on the new interface has to be begin only
after the BSS_CHANGED_BEACON_ENABLED flag is sent by mac80211
to the driver.
But, since we issue ATH_CHANCTX_EVENT_ENABLE_MULTICHANNEL as soon
as a new channel context is added, a switch occurs almost immediately
before BSS_CHANGED_BEACON_ENABLED is received. When a HW reset
is done for the new context, beacons are enabled for the
interface since "enable_beacon" in the BSS config maintained
in mac80211 is true - but the driver hasn't been notified yet.
This causes a panic, since the beacon interval is zero for this
interface and ath9k_cmn_beacon_config_ap() doesn't have a safety check.
Fix this panic by checking if the beacon params has been cached
for this context and use the "enable_beacon" flag maintained
locally in the driver. Also, recalculate the summary data
after the beacon params have been cached when BSS_CHANGED_BEACON_ENABLED
is received.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current opmode is managed, the ATH_OP_BEACONS flag
needs to be set only when there is a primary station interface
and it is associated/active.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In channel context mode, when a new context is added,
mac80211 issues a bss_info_changed() notfication when
preparing the connection for the new interface/context.
But, this is done prior to the mgd_prepare_tx() call which
is where we switch to the new context. Since the current
context will be different when the earlier bss_info_changed()
is handled, the beacon information for the VIF is not
updated, but discarded since the rules for the current context
disallows it.
In the subsequent association process for the new context/vif,
this becomes a problem because the beacon parameters are invalid.
This causes problems with the TSF timer, causing large jumps.
To fix this, check if the beacon info is being updated for a
different context and if so, allow it without any checks since
we limit the max. interfaces to two anyway.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend mac80211 set_coverage_class API in order to enable ACK timeout
estimation algorithm (dynack) passing coverage class equals to -1
to lower drivers. Synchronize set_coverage_class routine signature with
mac80211 function pointer for p54, ath9k, ath9k_htc and ath5k drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead.
-----BEGIN PGP SIGNATURE-----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=Qth6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/wil6210/wmi.c
Nothing important was being overwritten so it
didn't yield any bugs yet.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to log and debug via tracing
with more than 1 ath10k device on a system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove the ugly _access functions. Being explicit
is a good thing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents some fw revisions from crashing in
many cases when user is trying to run a
promiscuous station interface (e.g. sniffing,
4addr bridge).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix some cases where monitor start failure left
the driver in a confused state.
This also makes the monitor code simpler.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 5c771e7454
introduced a regression. On some systems spurious
interrupts could schedule a tasklet while tearing
down leading to, e.g.:
BUG: unable to handle kernel paging request at fe589030
IP: [<c1316fb0>] ioread32+0x30/0x40
...
Call Trace:
[<fe576c1b>] ath10k_pci_tasklet+0x1b/0x60 [ath10k_pci]
[<c1053fbe>] tasklet_action+0x9e/0xb0
[<c10534f1>] __do_softirq+0xf1/0x3f0
[<c1053400>] ? ftrace_raw_event_irq_handler_entry+0xa0/0xa0
[<c1004999>] do_softirq_own_stack+0x29/0x40
<IRQ>
[<c1053a76>] irq_exit+0x86/0xb0
...
[<c132d522>] do_pci_disable_device+0x52/0x60
[<c132d57f>] pci_disable_device+0x4f/0xb0
[<c132a961>] ? __pci_set_master+0x51/0x80
[<fe5740b3>] ath10k_pci_release+0x33/0x40 [ath10k_pci]
[<fe575d4b>] ath10k_pci_remove+0x7b/0x90 [ath10k_pci]
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tested-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If a station was reassociated, i.e. due to change
of supported rates update via sta_rc_update() the
num_legacy_stations would be (incorrectly) bumped
up leading to unbalanced usage of the var. This in
turn could lock rtscts protection up as enabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent changes done to start/restart sequences
broke hw recovery in some hw configurations. The
pci transport was stopped twice however due to a
workaround in the pci disabling code the
disable/enable for first msi interrupt was not
balanced. This ended up with irqs not being
properly re-enabled and the following print out
during recovery:
ath10k: failed to receive control response completion, polling..
ath10k: Service connect timeout: -110
ath10k: Could not init core: -110
Legacy interrupt mode was unaffected while msi
ranged mode would be partially crippled (it would
miss fw indication interrupts but otherwise it
worked fine).
This fixes completely broken fw recovery for a
single msi interrupt mode and fixes subsequent fw
crash reports for msi range interrupt mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to RCU_INIT_POINTER()'s block comment 3.a, it can be used if
"3. The referenced data structure has already been exposed to readers either
at compile time or via rcu_assign_pointer() -and-
a. You have not made -any- reader-visible changes to this structure since
then".
This case fulfills the conditions above because between the rcu_dereference()
call (cvif = rcu_dereference(ar->beacon_iter);) and the rcu_assign_pointer()
call there is no update of the "cvif" variable.
Therefore, this patch makes the replacement.
The following Coccinelle semantic patch was used:
@@
identifier v;
@@
v = rcu_dereference(...);
... when != rcu_dereference(...);
when != v = ...;
when != (<+...v...+>)++;
when != \(memcpy\|memset\)(...);
(
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., v);
|
if(...) {
... when != v = ...;
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., v);
... when any
}
)
Because there are cases where between a “rcu_dereference()” call and a
“rcu_assign_pointer()” call might be updates of the value that interests us,
the Coccinelle semantic patch ignores them and replaces with
"RCU_INIT_POINTER()" only when the update is not happening.
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the channel context correctly. Not doing this was
causing beacon loss in a P2P-GO/STA concurrent setup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a new context is being added in addition to the current one,
then send the ASSIGN event to abort a running scan since
the addition of a context is usually followed by VIF
assignment and further operations.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason why managed/p2p interfaces have to
be limited to one. IBSS is the only type that needs
a restriction.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be useful in handling addition/change of new
channel contexts.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move it inside a CONFIG_ATH9K_CHANNEL_CONTEXT ifdef
since it is not needed otherwise.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced in an earlier patch to handle
a compilation warning, but since the channel context
code has been mostly isolated, this is not required now.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
chanctx_work and next_chan are required only when
CONFIG_ATH9K_CHANNEL_CONTEXT is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finally move the 'offchannel' instance in ath_softc
inside a CONFIG_ATH9K_CHANNEL_CONTEXT cage. The offchannel
usage in ath9k_calculate_iter_data() is closed off with
an ifdef for now, since the state/opmode calculation is
common for both the channel context mode and the normal mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_vif_iter() was earlier used as an iterator
routine when calling a mac80211 utility. This is no
longer the case and hence we can mention the argument
type explicitly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_chanctx_check_active() is required only when channel contexts
are used. Make sure that it is not called in normal usage.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a routine to setup the offchannel
instance in ath_softc.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a function that handles queues in channel
context mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using these wrappers allows us to move the 'sched'
variable in ath_softc inside CONFIG_ATH9K_CHANNEL_CONTEXT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These routines are required only when
CONFIG_ATH9K_CHANNEL_CONTEXT is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if channel context usage is enabled before
calling ath_chanctx_event() from various parts of the
driver. Also, make sure that ath_chanctx_event() is
compiled only when CONFIG_ATH9K_CHANNEL_CONTEXT is
enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CONFIG_ATH9K_CHANNEL_CONTEXT to exclude:
ath_scan_complete()
ath_roc_complete()
ath_offchannel_next()
ath_scan_next_channel()
ath_scan_channel_duration()
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CONFIG_ATH9K_CHANNEL_CONTEXT to exclude more functions:
ath_offchannel_channel_change()
ath_scan_channel_start()
ath_scan_send_probe()
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Exclude these functions when CONFIG_ATH9K_CHANNEL_CONTEXT is not
enabled:
ath_chanctx_send_vif_ps_frame()
ath_chanctx_send_ps_frame()
ath_chanctx_defer_switch()
ath_chanctx_set_next()
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename the callback from ath9k_chanctx_force_active()
to ath9k_mgd_prepare_tx(). Also, move it to main.c and
group it with the other callbacks.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also compile it conditionally based on
CONFIG_ATH9K_CHANNEL_CONTEXT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the offchannel/sched timers and the chanctx work
inside the new function.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The carl9170_op_ampdu_action() function is used only by the mac80211
framework.
Since the mac80211 already takes care of checks and properly serializing
calls to the driver's function there is no need for the driver to do the same
thing.
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures that the module parameter "use_chanctx" is
visible only when CONFIG_ATH9K_CHANNEL_CONTEXT is selected.
Also register the channel context callbacks with mac80211 only
when it is explicitly enabled and compile them out of the driver
when CONFIG_ATH9K_CHANNEL_CONTEXT is not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CONFIG_ATH9K_CHANNEL_CONTEXT to conditionally
compile P2P-PS code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Channel contexts are supported only for P2P right now,
so make sure that the 'normal' path remains unaffected
by using a config option. This will also reduce the size
of the driver.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a few statements to debug channel context operation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kfree() null-checks its argument.
Found by smatch.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the missing null termination after strncpy().
This isn't actually a buffer overflow in this case since we use
snprintf() appropriately to fill the buffer passed by the caller,
but in the interest of not turning this into a bug down the road,
go ahead and force termination here.
Found by Coverity.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rxs->rate_idx is unsigned, so it will always be >= 0.
Found by Coverity.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a quick test with AR9271, TDLS seems to be working fine.
Tests were done with 2 Atheros AR9271 based devices with firmware
1.3 (sha1 8d49f928aa40ac53c729189bff1333cd373a7fb5), associated
with a WAP54G access point. TDLS worked fine both in WPA2 mode and
without encryption. Stations maintained ping flood traffic between
each other and towards the AP without significant losses.
Not tested with AR7010.
TDLS was enabled in earlier patches the same way for other
Atheros drivers:
ath9k (fd6562344d),
and carl9170 (d1f3de71a5).
Signed-off-by: Csaba Kiraly <csaba.kiraly@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some copy engine structures are target specific
and are uploaded to the device during
init/configuration.
This also cleans up a bit diag_mem_read/write
implicit byteswap mess leaving only
diag_access_read/write with an implicit endianess
byteswap.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The mapping is already defined in a structure. It
makes little sense to duplicate information stored
in it within a function.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to have copy engine
configuration structures spread across the whole
source file.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent crash dump patches introduced a regression.
If debugfs was disabled upon crash user could only
see the following:
[ 793.880000] ath10k: firmware crashed! (uuid n/a)
[ 793.890000] ath10k: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.1.467.2-1 api 2 htt 2.1
[ 793.890000] ath10k: debug 0 debugfs 0 tracing 0 dfs 1
The report was missing register dump. Fix it by
printing registers regardless if crash_data is
present or not.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it a lot easier to log and debug
messages if there's more than 1 ath10k device on a
system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).
For good measure, use it in ath6kl.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.
Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
'wil' released in wil_if_free(); save iomapped address aside to
properly unmap it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_priv_deinit(), wdev->netdev is accessed, so free_netdev()
should not be called before mentioned call.
Set wdev->netdev to NULL Make sure no more attempts to use it.
It is used for debug printk if not NULL.
This fix kernel panic on module unload and in case error on probe;
if memory allocation debugging enabled.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a module parameter to support setting the maximum
number of stations that can be associated to an AP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending scan request, if hardware is not ready, scan timer was started
and scan timeout mis-reported.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reading 'bf' file on debugfs, query beam forming status from firmware.
Ignore CID's that return error or return all zeros.
Remove obsolete code that used to maintain statistics on per-device basis,
as now it is reported be per-CID and current.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define tables for similar file entries, i.e.
- table for debugfs_create_file
- table for static parameters
- table for parameters that are members of "wil" structure
- table for blobs
- table for interrupt controllers
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If firmware broken on the boot time, Sparrow card enumerates as
device 0x302 instead of 0x310. Allow using this ID
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Typical time for hardware reset, as measured, is about 200..250 msec.
Adjust sleeping to use more relaxed msleep, increase sleep interval
and increase total sleep time to be about 1sec
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When resetting target in wil_target_reset(), error may occur.
Indicate error via error code. In case of error, don't attempt to further
interact with card, specifically don't attempt firmware download or
interrupts enabling.
Move wil_rx_fini() to be always executed to prevent memory leak.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix Copyright headers in all files changed in 2014, to mention 2014
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is important to halt USER CPU first, then MAC CPU
Otherwise, race happens in the firmware
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
expose reading RGF_MAC_MTRL_COUNTER_0 in debugfs
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transport buffers weren't flushed and processed
before queueing hw recovery request to mac80211.
This could in theory result in an unwanted htt/wmi
rx events being processed while mac80211 recovers
the device and possibly interfere or even crash
the system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are basically no more uses for
ar_pci->started. It is also perfectly safe to call
hif_stop without hif_start now.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Structures used by these functions are now
guaranteed to remain accessible until driver is
unregistered.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The old comment was a little out of date. HTT Rx
ring is a more relevant problem when stopping
transport layer.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible on a host system running low on
memory to end up with no rx buffers on pci pipes.
This makes the driver more robust as it won't fail
to start if it can't allocate all rx buffers right
away. If it is fatal then upper layers will notice
trouble anyway.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary to have a dedicated irq
handler just for the sake of catching early fw
crashes anymore. It is now safe to use one handler
even during early stages of device boot up.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes two corner cases.
One is a race between disabling copy engine
interrupts and unhandled pending interrupts on the
host. This could end up with a runaway tasklet and
consequently memory leak of a few copy engine
rx buffers.
The other one is an unexpected (and non-maskable
via device CSR) MSI fw indication interrupt during
teardown. This could trigger the same problem as
the first corner case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to overwrite send_cb
and recv_cb callbacks over and over again whenever
transport starts. Just make sure to unmask copy
engine interrupts when starting.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make sense to re-init irqs completely
whenever transport is started/stopped. Do it just
once upon probing/removing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Wrong register was being set up. This could
prevent firmware from booting in some rare cases
when using legacy interrupts.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware probing is done only once when driver is
registered and firmware version is guaranteed to
remain the same until driver is unregistered.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes users forget to include important info like firmware version,
so better to print all the info.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Better to have a clear name for the function. While at it, clear up the title
for the register dump.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store the firmware registers and other relevant data to a firmware crash dump
file and provide it to user-space via debugfs. Should help with figuring out
why the firmware crashed.
kvalo: remove dbglog support, rework and refactor the code to avoid ifdefs and
otherwise simplify it as well
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_pci_diag_read32() is for reading u32 from a device and ath10k_pci_diag_read_hi()
is a helper for reading data using "host interest" table.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Service mapping for main firmware branch was incorrectly used for 10.x firmware
and vice-versa. This caused wmi_services in debugfs to print wrong values.
This fixes commit cff990ce7d ("ath10k: fix wmi service bitmap debug") where
for some reason there was either a conflict that wasn't resolved properly or
git had a bad day.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
If spectral is unregistered after mac80211, the relayfs file has already
been removed recursively by mac/cfg80211, and spectral tries to remove
the file once more, thus leading to double free problems. Better clean
up spectral before to avoid that problem.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds device ID 402 to support QCA6234X found in APQ8064 SOC
in IFC6410 board.
Tested with mainline mmci sdio driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Check vdev map has space before calling ffs,
fix invalid cleanup in failure to create vdev
case.
Open-code the BIT() logic since BIT does not properly
handle 64-bit bitfields and future patches will make
use of larger bitfields.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is not necessary anymore. There are no more
uncontrolled htc tx entry points.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make probe/remove functions shorter and easier to
understand.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ATH10K_PCI_FEATURE_MSI_X was originally
introduced to support both chips QCA988Xv1 and
QCA988Xv2. Since v1 isn't supported anymore it
doesn't make sense to keep the feature flag
around. Since this is the last one remove the
whole thing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The soc powersave was disabled by default. It
never was fully tested. Some hw apparently had
problems with it and the implementation itself had
a possible race.
Just remove the refcounting and simply wake up the
device when probing and put to sleep when
removing.
kvalo: make ath10k_pci_wake() and _sleep() static
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the common convention of embedding private
structures inside parent structures. This
reduces allocations and simplifies pci probing
code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This aims at fixing some rare scan bugs related to
firmware reporting unexpected scan event
sequences.
One such bug was if spectral scan phyerr reporting
prevented firmware from properly propagating scan
events to host. This led to scan timeout. After
that next scan would trigger scan completed event
first (before scan started event) leading to
ar->scan.in_progress and timeout timer states to
be overwritten incorrectly and making the very
next scan to hang forever.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This also reduces the cruft of printing scan event
names in capitals.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.x and main firmware branches have
conflicting WMI service bitmap definitions.
This also fixes WMI services parsing on big-endian
hosts and changes debugfs output to be more human
friendly.
kvalo: remove braces and the last semicolon from SVCSTR()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver assumes that endpoint 4 is always an interrupt endpoint.
Unfortunately the type differs between high-speed and full-speed
configurations while in the former case it is indeed an interrupt
endpoint this is not true for the latter case - here it is a bulk
endpoint. When sending URBs with the wrong type the kernel will
generate a warning message including backtrace. In this specific
case there will be a huge amount of warnings which can bring the system
to freeze.
To fix this we are now sending URBs to endpoint 4 using the type
found in the endpoint descriptor.
A side note: The carl9170 firmware currently specifies endpoint 4 as
interrupt endpoint even in the full-speed configuration but this has
no relevance because before this firmware is loaded the endpoint type
is as described above and after the firmware is running the stick is not
reenumerated and so the old descriptor is used.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
Conflicts:
net/6lowpan/iphc.c
Minor conflicts in iphc.c were changes overlapping with some
style cleanups.
John W. Linville says:
====================
Please pull this last(?) batch of wireless change intended for the
3.17 stream...
For the NFC bits, Samuel says:
"This is a rather quiet one, we have:
- A new driver from ST Microelectronics for their NCI ST21NFCB,
including device tree support.
- p2p support for the ST21NFCA driver
- A few fixes an enhancements for the NFC digital laye"
For the Atheros bits, Kalle says:
"Michal and Janusz did some important RX aggregation fixes, basically we
were missing RX reordering altogether. The 10.1 firmware doesn't support
Ad-Hoc mode and Michal fixed ath10k so that it doesn't advertise Ad-Hoc
support with that firmware. Also he implemented a workaround for a KVM
issue."
For the Bluetooth bits, Gustavo and Johan say:
"To quote Gustavo from his previous request:
'Some last minute fixes for -next. We have a fix for a use after free in
RFCOMM, another fix to an issue with ADV_DIRECT_IND and one for ADV_IND with
auto-connection handling. Last, we added support for reading the codec and
MWS setting for controllers that support these features.'
Additionally there are fixes to LE scanning, an update to conform to the 4.1
core specification as well as fixes for tracking the page scan state. All
of these fixes are important for 3.17."
And,
"We've got:
- 6lowpan fixes/cleanups
- A couple crash fixes, one for the Marvell HCI driver and another in LE SMP.
- Fix for an incorrect connected state check
- Fix for the bondable requirement during pairing (an issue which had
crept in because of using "pairable" when in fact the actual meaning
was "bondable" (these have different meanings in Bluetooth)"
Along with those are some late-breaking hardware support patches in
brcmfmac and b43 as well as a stray ath9k patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts a driver in drivers/net/* to use the
module_usb_driver() macro which makes the code smaller and a
bit simpler.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adds the spectral scan feature for ath10k. The spectral scan is triggered by
configuring a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.
Essentially, to try it out:
ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples
This feature is still experimental. Based on the original RFC patch of
Sven Eckelmann.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k and ath10k will share the definitions of the debugfs spectral
structures and enums. Having them in the same place helps to avoid conflicts.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases during heavy tx vdev stop-start
would timeout on vdev synchronization causing
traffic to stall for a few seconds.
Instead of stop-starting use a dedicated vdev
restart command and down vdevs explicitly before
doing so.
This gets rid of the synchronization
warnings/timeouts and makes channel switching
smoother during traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not doing so, could fail on device probing when use_chanctx
module param is set to true.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print sequence number, AMSDU_MORE flag and AC when additional
debug enabled in RX path. This is usefull for debugging purpose.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A-MSDU 4addr frames weren't reconstructed properly
and in some cases this resulted in a warning:
br0: received packet on wlan0.sta1 with own address as source address
Since this was only related to A-MSDU it would
trigger when more intense traffic was generated.
Reported-by: Vu Hai NGUYEN <vh.nguyen@actiasodielec.fr>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville says:
====================
pull request: wireless-next 2014-07-25
Please pull this batch of updates intended for the 3.17 stream!
For the mac80211 bits, Johannes says:
"We have a lot of TDLS patches, among them a fix that should make hwsim
tests happy again. The rest, this time, is mostly small fixes."
For the Bluetooth bits, Gustavo says:
"Some more patches for 3.17. The most important change here is the move of
the 6lowpan code to net/6lowpan. It has been agreed with Davem that this
change will go through the bluetooth tree. The rest are mostly clean up and
fixes."
and,
"Here follows some more patches for 3.17. These are mostly fixes to what
we've sent to you before for next merge window."
For the iwlwifi bits, Emmanuel says:
"I have the usual amount of BT Coex stuff. Arik continues to work
on TDLS and Ariej contributes a few things for HS2.0. I added a few
more things to the firmware debugging infrastructure. Eran fixes a
small bug - pretty normal content."
And for the Atheros bits, Kalle says:
"For ath6kl me and Jessica added support for ar6004 hw3.0, our latest
version of ar6004.
For ath10k Janusz added a printout so that it's easier to check what
ath10k kconfig options are enabled. He also added a debugfs file to
configure maximum amsdu and ampdu values. Also we had few fixes as
usual."
On top of that is the usual large batch of various driver updates --
brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action.
Rafał has also been very busy with b43 and related updates.
Also, I pulled the wireless tree into this in order to resolve a
merge conflict...
P.S. The change to fs/compat_ioctl.c reflects a name change in a
Bluetooth header file...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 10.2 firmware is a successor of 10.1 firmware
(formerly identified as 10.x). Both share a lot
but have some slight ABI differences that need to
be taken care of.
The 10.2 firmware introduces some new features but
those can be added in subsequent patches. This
patch makes ath10k boot and work with 10.2 with
comparable functionality to 10.1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Different firmware may support different numbers of
vdevs. Use value that is always out of range for all
firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.x firmware does not support IBSS mode at
all. It can't beacon and it crashes when trying to
scan.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware doesn't perform Rx reordering so it is
left to the host driver to do that.
Use mac80211 to perform reordering instead of
re-inventing the wheel.
This fixes TCP throughput issues in some
environments.
Reported-by: Denton Gentry <denton.gentry@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We have interfaces. Remove the open coded cruft. Reduces text size
along with the code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
If an aggregation session fails, frames still end up in the driver queue
with IEEE80211_TX_CTL_AMPDU set.
This causes tx for the affected station/tid to stall, since
ath_tx_get_tid_subframe returning packets to send.
Fix this by clearing IEEE80211_TX_CTL_AMPDU as long as no aggregation
session is running.
Cc: stable@vger.kernel.org
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible to enter an endless loop while
processing a single pci copy engine pipe. This
could effectively render ath10k incapable of
responding to any requests.
An example case when this could happen is when
firmware generates a lot of events, e.g. spectral
scan phyerr via WMI.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently fw/hw generates a corrupted QoS Control
Field in Qos NullFunc frames. The only way to
workaround this is to downgrade frames to
NullFunc. This should be okay since powersave is
done by fw/hw and these frames are only used for
CQM purposes (e.g. from hostapd to check if
station is still connected).
This doesn't fix any user visible bug that I know
of. It just prevents from sending out funky frames
on the air.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It always bugged me how tid is computed and stored
in a temporary var before written to the control
buffer. It was confusing and it made it difficult
to work with tx helpers.
While at it rename the qos workaround function as
it was misleading - it's not a workaround but
preparation for nwifi tx mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware could request inspection of some
submitted tx requests. Since the callback wasn't
implemented it was possible to bleed tx msdu_ids
which could translate to tx flushing timeouts.
There's nothing ath10k can do to help firmware
with tx processing now so just report all tx
frames as already inspected to prevent firmware
from sending up inspection events and force it to
report regular tx completion indications with
discard status.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently iomap writes that unmask CE irqs aren't
propagated properly sometimes. Before failing try
to poll for the control response message as it may
have been delivered without an interrupt.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set up tx power for each MRR segment in the tx descriptor
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packets originally buffered for the regular hardware tx queues can end
up being transmitted through the U-APSD queue (via PS-Poll or U-APSD).
When packets are dropped due to retransmit failures, the pending frames
counter is not always updated properly.
Fix this by keeping track of the queue that a frame was accounted for in
the ath_frame_info struct, and using that on completion to decide
whether the counter should be updated.
This fixes some spurious transmit queue hangs.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New register area defined in the firmware
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware sets this register with the offset of the firmware trace area
within the peripheral memory region. Critical for the firmware trace
to work
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use single data source for all information regarding the firmware
memory map. With this change "ucode_xxx" regions disappears since
they are in fact part of larger "upper area" region
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If copy_from_user() fails, buffer allocated for parameters would leak
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Variable 'ctx' declarad again in the inner loop. Should use
one from outer loop instead.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New hardware release appears; it require some changes to properly support it.
Introduce struct wil_board and "board" attribute in wil6210_priv;
keep hardware variant information in this structure.
fill it on probe(). Used in the reset flow.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx ring index was immediately trimmed with a
bitmask. This discarded the 0xFFFFFFFF error case
(which theoretically can happen when a device is
abruptly disconnected) and led to using an invalid
tx ring index. This could lead to memory
corruption.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible for tx completion not to be
processed. In that case an old stack pointer was
left on copy engine tx ring. Next bmi exchange
would immediately pop it and use complete() on the
completion struct there causing corruption.
Make sure to wait for both tx and rx completions
properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware probing worker failed it called
device_release_driver() which synchronously called
remove() pci callback. The callback in turn waited
for the worker that called it to finish resulting
in a deadlock.
Waiting for a completion instead of a worker, like
some other drivers do, doesn't seem like the best
idea either:
Syscall Worker
probe_fw()
rmmod
dev_lock()
pci->remove()
wait_for_completion()
complete_all()
device_release_driver()
dev_lock()
[sleep]
free(ar)
dev_unlock()
[resume]
There's no guarantee that Worker upon resuming can
still access any data/code of the module.
Leaving device bound to a driver is not as harmful
as deadlocking so remove the call to
device_release_driver() while a proper solution is
figured out.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This change enables ath6kl driver to support ar6004 hw3.0. At the same time do
some fixes in firmware initialisation which applies to ar6004 hw1.3 as well.
Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of the firmware versions support rate tables up to mcs15, add support for
that.
Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rx flush was not implemented for htc pipe, add that now. Doesn't fix any known
issues.
Also free the skb if htc control messages get canceled.
Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The functionality defined through these flags were actually firmware features
which can change between firmware versions. To make it possible to support
different firmware versions with the same driver, convert the flags to firmware
feature flags.
For backwards compatibility support for old ar6004 firmware FW
API 3 or smaller images we forcefully set the feature bits in the driver.
Starting from FW API 5 the firmware image needs to set them.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
tmp may be used uninitialized if ath6kl_bmi_read() returns an error.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow to setup maximum subframes for AMSDU and AMPDU aggregation
via debugfs htt_max_amsdu_ampdu file.
Eg.
echo "2 64" > htt_max_amsdu_ampdu
will setup maximum amsdu subframes equal 2 and
maximum ampdu subframes equal to 64.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Right now sleep duration is configured as beacon interval. It should be
the multiple of beacon interval by listen period which helps to
reduce station power consumption.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier the listen interval is used to decide switching between
operating and off-channels during bgscan and to improve throughput,
the listen interval is reduced to 1. After optimiztion in scan
state machine, listen period is not used for decision making and
hence reverting it back to original value.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon configurations are not cached properly after the station
associates with AP. Not handling BEACON_INFO, is failing to update
dtim period and also it is causing below warning message.
WARNING: CPU: 1 PID: 0 at drivers/net/wireless/ath/ath9k/recv.c:548
ath_rx_tasklet+0xc89/0xca0 [ath9k]()
Call Trace:
[<c14669c9>] dump_stack+0x48/0x69
[<c104f1a2>] warn_slowpath_common+0x82/0xa0
[<fd38c2f9>] ? ath_rx_tasklet+0xc89/0xca0 [ath9k]
[<fd38c2f9>] ? ath_rx_tasklet+0xc89/0xca0 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Treat frames that underwent a CCK or OFDM restart as frames with an invalid CRC.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the FIF_FCSFAIL filter flag is set, pass frames with CRC errors.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix tx gain table index on fast channel change for AR953x.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.
As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
drivers/net/wireless/ath/ath9k/main.c:299 ath_reset_internal()
error: we previously assumed 'hchan' could be null (see line 293)
Cc: Felix Fietkau <nbd@openwrt.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some platforms, cycles_t is 64-bit, and gcc generates call to
__udivdi3 for straight division of cycles_t/cycles_t. This leads
to compilation failure, as this function is not exist in the kernel
runtime. do_div() to rescue
Original report:
tree: git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master
head: 2e91606f5e
commit: 7c0acf868d [81/103] wil6210: Tx performance monitoring
config: i386-randconfig-ha3-0620 (attached as .config)
All error/warnings:
drivers/built-in.o: In function `wil_vring_debugfs_show':
>> debugfs.c:(.text+0x39b9be): undefined reference to `__udivdi3'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide both event (netif_tx_[stop|wake]) tracking via printk;
and state via debugfs 'info'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Track number of interrupts and Tx/Rx packets;
expose through debugfs 'info'. Reset upon read.
Used to analyse effectivness of interrupt coalescing and NAPI.
Read twice with some interval like
cat info > /dev/null; sleep 1; cat info
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use 'info' debugfs entry for misc. assorted information.
Start with indication whether platform is AC-powered;
will use it later for power related decisions
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are platforms where INTx can't be routed by ACPI,
this leads to pci_enable_device failure. Re-try pretending we have
MSI already configured; in this case pci_enable_device do not try
to configure INTx. However, MSI could still work.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Dan Carpenter <dan.carpenter@oracle.com>:
The patch a715c7ddd6: "wil6210: improve debug for WMI receive" from
May 29, 2014, leads to the following static checker warning:
drivers/net/wireless/ath/wil6210/wmi.c:746 wmi_recv_cmd()
info: ignoring unreachable code.
drivers/net/wireless/ath/wil6210/wmi.c
739 spin_unlock_irqrestore(&wil->wmi_ev_lock, flags);
740 {
741 int q = queue_work(wil->wmi_wq,
742 &wil->wmi_event_worker);
743 wil_dbg_wmi(wil, "queue_work -> %d\n", q);
744 }
745 }
746 if (n > 1)
^^^^^^^^^^
We never reach this if statemtent.
747 wil_dbg_wmi(wil, "%s -> %d events processed\n", __func__, n);
748 }
Exit loop with "break", not "return".
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New registers area introduced, mark corresponded address range as valid
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the pcie_bus.c, knowledge about debugfs is not necessary
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the AP-like interface, if "disconnect all" requested,
every station should be deleted with cfg80211_del_sta().
Implement this behavior.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Tx path, when vring for the destination not found,
it was considered as error and message was printed unconditionally.
However, this situation is normal after disconnect. If disconnect was while
heavy traffic load, lots of Tx packets will be dropped and this would
cause significant amount of prints in dmesg.
Demote messages priority from 'error' to 'debug'.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expose operational frequency and link info
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print to dmesg when FW error notification is about to be sent
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Interrupt threshold registers may be written to.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usable for debugging, to be able to obtain FW traces
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For performance monitoring, trace time intervals when Tx vring
is idle/not idle. Use CPU cycle counter for this, because jiffies is
too rough, and other precise time measurement methods involve
overhead while get_cycles() should be fast.
This used to provide some estimation for percentage when Tx vring
was idle, i.e. when hardware is under-utilized.
Estimation is not precise because of many reasons - CPU frequency scaling,
grt_cycles() may be per core etc. But still, it is good estimation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
print used/available counters on debugfs;
print to dmesg when Tx vring becomes empty
This aids with performance investigation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
print essential info to dmesg
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_cfg80211_start_ap(), debug print selected data:
- beacon (before and after fix-up)
- crypto parameters
- mark start/stop AP invocation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inform cfg80211 about Tx result
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide 2 files on the debugfs:
- "rxon": write channel (1..4) to open Rx on it, 0 to rxoff
- "tx_mgmt": write binary frame, starting from MAC header
one need to care about turning receiver on/off before/after tx_mgmt
Correct sequence is:
echo $channel > rxon
cat mfmt_frame > tx_mgmt
echo 0 > rxon
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use seperate tx queue for each AC in each channel context and expose
these information to mac80211 to avoid stopping one channel context
leads to stopping the entire traffic for that AC even on other contexts.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the TSF based hardware timer for a channel switch.
Also set up backup software timer, in case the gen timer fails.
This could be caused by a hardware reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF time might have been updated by the incoming beacon,
need update the channel switch timer to reflect the change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multi channel context (AP + STA case), adjust the TSF time of
the AP chanctx to keep its beacons at half beacon interval offset
relative to the STA chanctx.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update current offchannel duration during scan or roc request.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a basic state machine for switch channel context
for beacon transmission.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Save TSF in channel context for multiple operating channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retrieve appropriate operating channel context while switching
between operating and off channels.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add channel context operations (add, remove, change, assign and
unassign) to enable support for multiple channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add remain on channel support in order to enable multi-channel
concurrency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement hw_scan support for enabling multi-channel cuncurrency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While leaving from or entering to active channel context, send out
nullfunc frame to inform to the AP about the presence of station.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force queueing of all frames that belong to a virtual interface on
a different channel context, to ensure that they are sent on the
correct channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel context worker is used to switch to next requested
channel context.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to maintain per-channel ACs list.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel context structure is defined to enable
multi-channel concurrency support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Pull trivial tree changes from Jiri Kosina:
"Usual pile of patches from trivial tree that make the world go round"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
staging: go7007: remove reference to CONFIG_KMOD
aic7xxx: Remove obsolete preprocessor define
of: dma: doc fixes
doc: fix incorrect formula to calculate CommitLimit value
doc: Note need of bc in the kernel build from 3.10 onwards
mm: Fix printk typo in dmapool.c
modpost: Fix comment typo "Modules.symvers"
Kconfig.debug: Grammar s/addition/additional/
wimax: Spelling s/than/that/, wording s/destinatary/recipient/
aic7xxx: Spelling s/termnation/termination/
arm64: mm: Remove superfluous "the" in comment
of: Spelling s/anonymouns/anonymous/
dma: imx-sdma: Spelling s/determnine/determine/
ath10k: Improve grammar in comments
ath6kl: Spelling s/determnine/determine/
of: Improve grammar for of_alias_get_id() documentation
drm/exynos: Spelling s/contro/control/
radio-bcm2048.c: fix wrong overflow check
doc: printk-formats: do not mention casts for u64/s64
doc: spelling error changes
...
Firmware 10.x supports up to 8 virtual AP interfaces, but in a DFS
channel it was possible to create only 7 interfaces as ath10k internal
creates a monitor interface for DFS. Previous vdev map initialization
was missing enough space for 8 + 1 vdevs due to wrong define used and
that's why there was no space for 8th interface. Use the correct define
TARGET_10X_NUM_VDEVS with 10.x firmware to make it possible to create
the 8th virtual interface.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While fixing a bug reported by Avery I went ahead
and added a warning suspecting there might be
something more to the bug. This ended up with
people reporting they see warnings during heavy
traffic. This bought me some time and helped me
understand the problem better - apparently fw/hw
can report a chained msdus as follows: 1 msdu, 1
chained, 1 msdu (0 length).
The patch removes the extra check but leaves the
other change that fixed the original skb_push
panic bug (msdu_chaining was overwritten in an
unfortunate way which made the above example to
be treated as non-chained case).
Reported-by: Yeoh Chun-Yeow <yeohchunyeow@gmail.com>
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Print Kconfig options enabled/disabled in the build.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Print message if no events received. This should not happen.
If it is, it points to the problem in firmware.
Track also cases when multiple events processed in one IRQ
Print information as soon as possible - mbox pointers and
event header right after reading it. This helps to identify potential
problem with memory allocation for the event buffer.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 does not support WDS and DFS with channel context
drivers. So advertise these features only when the driver is not
supporting channel context and modparam "use_chanctx" is introduced
for preparing channel context support in ath9k.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of receiving frame with sequence number far greater than current,
wil_release_reorder_frames() will iterate many times over empty buffer.
Optimize this case by checking buffer emptiness and simply update
head_seq_num without iterating.
Suggested-by: Vladimir Shulman <Vladimir.Shulman@Wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use proper format %pad for the dma_addr_t arguments;
prefix %p with 0x, as %p don't print is by itself
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If scan has not finished in some reasonable time (10sec), interpret it as
if firmware error occurs but was not reported. Firmware should report
scan completion for every scan request, so it is error condition indeed.
Perform firmware recovery procedure.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide clear definition of the watermarks for the vring descriptor space.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case there is something fundamentally wrong with the firmware
(example: RF cable disconnected), FW will always crash immediately
after reset. This leads to infinite fw error recovery loop.
Count consecutive unsuccessful error recovery attempts in a short period
of time, and stop doing recovery after some reasonable count.
It is still possible to manually reset fw doing
interface down/up sequence.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Obey 802.11 spec that defines max. data size 7920 bytes
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pm_lock is taken twice while syncing HW TSF of p2p vif.
Fix this by taking the lock at caller side.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: fix possible hang on flush" changed the receive code
to always link rx descriptors of processed frames, even when flushing.
In some cases, this leads to flushed rx buffers being passed to the
hardware while rx is already stopped.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make DFS pulse interval calculation independent
from CONFIG_ATH9K_DEBUGFS.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents leaving incomplete scatter-gather
transfer on CE rings which can lead firmware to
crash.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to read invalid state of CE ring
buffer indexes. This could lead to scatter-gather
transfer failure in mid-way and crash firmware
later by leaving garbage data on the ring.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It seems ath10k firmware gives us no way to know
the rssi for rx-fragments.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW creates self-peer for AP internally.
This prevents ath10k from trying to create
explicit self-peer during hw recovery and thus
prevents a timeout and a warning during teardown:
ath10k: removing stale peer $AP_BSSID from vdev_id 0
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All configuration sequences should be protected
with conf_mutex to avoid concurrent/conflicting
requests.
This should make sure that wep tx key setup is not
performed while hw is restarted (at least).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes sure no further tx requests are
submitted to HTT before driver teardown.
This should prevent invalid pointer/NULL
dereference on htt tx pool in ath10k_htt_tx() in
some cases of heavy traffic.
kvalo: remove the WARN_ON() if conf_mutex is held
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reduces risk of races and prepares for more
hw restart fixes.
It also makes sense to perform teardown after
mac80211 starts its restart routine as it
guarantees it has stopped itself by then
(including tx queues).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes failpath when override AC pdev param
setup fails and makes other pdev params setting
fail as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If ath10k was built into the kernel it could stall
booting for 120 seconds by default (60 seconds for
each firmware API variant) waiting for firmware
files before userspace was ready or filesystems
mounted.
Fix this by making the core registering
asynchronous.
This also shoves off about 1 second from boot time
on most systems since the driver is now mostly
initialized in a worker and modprobe takes very
little time to complete.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The tasklet is already guaranteed to be killed on
the teardown path.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will avoid unnecessary forward declaration of
any kind in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents protected flag being stripped from
undecrypted raw sniffed frames when monitor
interface is active.
Reported-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Tested-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The channel_switch_beacon callback is optional, so it doesn't have to
be defined if it's not going to do anything useful with it. Both
ath9k and ath10k define the callback and just returns. This commit
removes them.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
tmp may be used uninitialized if ath10k_bmi_read_memory() returns
an error.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recently there was a bug discovered that involved
hif_stop() being called twice that ended up with a
double free_irq() call but it only manifested with
multiple MSI interrupts mapping.
Catch this kind of a problem early in driver
regardless of interrupt mapping.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to call hif_stop() 2 times through
ath10k_htc_connect_init() timeout failpath which
could lead to double free_irq() kernel splat for
multiple MSI interrupt case.
Re-order init sequence to avoid this problem. The
HTC stop shouldn't stop HIF implicitly since it
doesn't implicitly start it. Since the re-ordering
required some functions to be split/removed/renamed
rename a few functions to make more sense while at
it.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On idle state, sleep timer is scheduled to put the chip into fullsleep.
But during suspend, this timer is scheduled after the chip is moved to
fullsleep forcibily. This is causing below unnecessary error messages
in kernel log during suspend.
ath: phy2: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000
!= 0x00000000
ath: phy2: RX failed to go idle in 10 ms RXSM=0xdeadbeef
ath: phy2: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
DMADBG_7=0xdeadbeef
Reported-by: Arkh4mKn1ght <arkh4mkn1ght@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The keycache index is used to abort transmission for given station
when it goes to sleep state. But the commit "ath9k_hw: Abort transmission
for sleeping station" is not handling multi-key station. Fix that.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DFS pulse interval printing is only available
when CONFIG_ATH9K_DEBUGFS is set.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170_usb_probe() does not handle request_firmware_nowait() failure
that leads to several leaks in this case.
The patch adds all required deallocations.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Verified that target's tx/rx chain register is set appropriately,
and that the tx rate goes down as number of chains
decrease, but I did not actually try to verify antenna
ceased to transmit when disabled.
kvalo: move ar->supp_*_chainmask initialisation to ath10k_mac_register()
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently Oleksij's compile testing was no better than mine initially
was... :-(
Cc: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/ath/ath9k/htc_drv_txrx.o
drivers/net/wireless/ath/ath9k/htc_drv_txrx.c: In function ‘ath9k_rx_prepare’:
drivers/net/wireless/ath/ath9k/htc_drv_txrx.c:1006:2: warning: passing argument 2 of ‘ath9k_htc_err_stat_rx’ from incompatible pointer type [enabled by default]
ath9k_htc_err_stat_rx(priv, &rx_stats);
^
In file included from drivers/net/wireless/ath/ath9k/htc_drv_txrx.c:17:0:
drivers/net/wireless/ath/ath9k/htc.h:380:20: note: expected ‘struct ath_htc_rx_status *’ but argument is of type ‘struct ath_rx_status *’
static inline void ath9k_htc_err_stat_rx(struct ath9k_htc_priv *priv,
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The data transmission to the power save station should be aborted
immediately, whenever the station informs sleep state. Right now
the frames queued into into hardware are being transmitted until
the hardware detects the power save station based excessive retries
of the data frames due to unacknowlegdement. Then remaining frames
are returned with filetered status and might be retried later by
driver or mac80211.
Per WFA certification testing, AP should not send out more than two
frames after processing nullfunc with PM bit set from associated
station. To speed up tx filtering, the pending frames in hardware
queues for given station will be aborted immediately via tx filter
registers. This transmit filters can be ignored if the descriptor
is having invalid destination index or clear destination mask set.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This also propagates through the drivers.
The orinoco driver uses the cfg80211 API structs for internal
bookkeeping, and so needs a (void *) cast that removes the
const - but that's OK because it allocates those pointers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add initial values for JP DFS pattern detector.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix sending and receiveing protected managment frames.
Lack of protected flag for received protected action frames
causes report these frames as unprotected robust action frames.
If the driver in AP mode sent frame with protected flag and
CCMP header using IEEE80211_KEY_FLAG_SW_MGMT_TX flag,
the FW encrypted frames once again. From user side all
received SA Query Requests and Responses were skipped and
all protected action frames were sent as malformed packets.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On ARM-based (MSM mach), the pci_assign_resource() is passing
some invalid pointers and leading to L2 cache errors,
what prevents the PCI communication completly.
So far I have not found this funtion to be directly called by
any other wifi driver and did not found this assigning needed
on any other platform. So removing it completely.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be useful for early initialization
debugging, i.e. ROM crashes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes warm reset works upon retry. It might be
related to imperfect warm reset routine, but for
now let's just do the retries.
This should improve the reliability of some chips
that hang/crash with cold reset which is used as a
last resort if warm reset fails.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Warm reset is now able to recover after device
crashes which required a cold reset before.
This should greatly reduce chances of getting data
bus errors or host system freezes due to buggy
cold reset on some chips.
kvalo: use ath10k_pci_soc_*()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During remain on channel request, ANI worker thread is not stopped
before doing hw reset. This is causing kernel crash in
hw_per_calibration. This change ensures that ANI is stopped before
doing chip reset and it will be rescheduled later when the chip is
configured back to home channel and having valid bss.
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently firmware can sometimes report a
sequence with the first rx descriptor saying it's
not the last MSDU. In that case msdu_chaining
value could be overwritten saying it's not a
chained MSDU. This in turn led to skb_push panic
as the frame could be treated as an A-MSDU instead
of a chained MSDU.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
msdu_payId was read before txrx tasklet was killed
so it was possible to end up using an invalid
sk_buff pointer leading to a panic.
Make sure to sanitize rx ring sk_buff pointers and
make the clean up go through all possible entries
and not rely on coherent-DMA mapped u32 index
which could be (in theory) corrupted by the device
as well.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
and use it. This move need changes in both drivers.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Systems with multiple DFS channel detectors need to track
timestamp of previous pulse per instance to display the
correct pulse interval.
Since the interval value is used for debug printing only,
this is a non-functional modification.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Originally Helmut posted a v2 of the "ath9k: Allow platform override
without EEPROM override", but I had prematurely commited the original
as commit 552a515707. This commit restores the tree to what Helmut
intended with his v2 submission. -- JWL
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new platform data flag "use_eeprom" that indicates that the eeprom
found on the card itself should be used instead of the one present in
the platform data.
This allows to override the MAC address of a PCI card while preserving
the eeprom data from the card itself.
The default behavior is preserved.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SREV register in the WMAC register space does not contain the chip
revision, so it needs to be passed in from the kernel.
With an updated kernel, this fixes tx gain table selection.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A similar patch fixed crashes seen on an ath9k system
when testing against a broken ath10k AP. This patch
is slightly less protective, but probably will do the
job and is less redundant.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust FIR filter co-efficients to improve EVM for 11b rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rfsat gainchange hysteresis of rf_gain stuck with large
interference present.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I was reading ath5k power setting code and
noticed typing error in ath5k_hw_txpower function.
Invalid value was written to AR5K_PHY_TXPOWER_RATE_MAX
register.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some corner cases where the driver could get stuck with a full
tid queue that is paused, leading to a software tx queue hang.
Since the tx queueing rework, pausing per-tid queues on aggregation
session setup is no longer necessary. The driver will assign sequence
numbers to buffered frames when a new session is established, in order
to get the correct starting sequence number.
mac80211 prevents new frames from entering the queue during setup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the amount of noise fluctuates strongly, low immunity settings
can sometimes disrupt signal detection on AR913x chips. When that
happens, no OFDM/CCK errors are reported anymore, and ANI tunes the
radio to the lowest immunity settings.
Usually rx/tx fails as well in that case.
To fix this, keep noise immunity settings at or above ANI default level,
which will keep radio parameters at or above INI values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: move sc_flags to ath_common" moved setting
ATH_OP_INVALID flag below ieee80211_register_hw. This is causing
the flag never being cleared randomly as the drv_start is called
prior to setting flag. Fix this by setting the flag prior to
register_hw.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon data wasn't properly cleared during early
phase of recovery. This in turn caused firmware to
crash because the beacon data was submitted before
vdevs were fully re-configured. Ultimately the
device was considered wedged and nothing worked
until driver was reloaded.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DMA mapping of next beacon failed ath10k leaked
the beacon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DMA mapping of next beacon failed it was
possible for next SWBA to access a pointer that
was already unmapped and freed. This could cause
memory corruption.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If for some reason mac80211 wouldn't stop
beaconing gracefully and just removed interface of
a running AP/IBSS interface it was possible to
leak pending beacon DMA mapping. It's very
unlikely but better safe than sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to even try suspending
the device when recovering. Recovering means the
device is unresponsive and waiting for suspend
procedure means taking a 3 second timeout waiting
for tx credits.
This speeds up firmware recovery significantly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When warm resetting it's possible for device to
crash during initialization. Instead of waiting 3
seconds just return failure as soon as
FW_IND_EVENT_PENDING is set.
This speeds up device bootup and recovery in some
cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This just makes it easier to tell apart different
kinds of bringup failure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When using scatter-gather, more descriptor entries get used.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes, due to the race between Rx path and WMI_BA_STATUS_EVENTID WMI event,
few frames may be passed to the stack before reorder buffer allocated.
Then, after BACK establishment, it start getting frames with sequence number ahead of
SSN, and it get interpreted as missing frames. Then, BACK mechanism will wait
for missing frames; data traffic will be stopped. In case of interface configured
for DHCP, this data delay causes DHCP failure.
Relax checking for sequence number; use sequence of 1-st frame handled by the buffer
as SSN for this buffer.
This is work-around, real fix should be done when proper BACK mechanism implemented.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- add pcp_max_assoc_sta to the struct wmi_pcp_start_cmd
- enum for the scan ststus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reshuffle prints to consolidate firmware/hardware information
report upon card init
Convert print for unhandled MISC ISR bits to "debug" - it is
normal situation and not an "error"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use generic TSF timers to trigger powersave state changes based
information from the P2P NoA attribute.
Opportunistic Powersave is not handled, because the driver does not
support powersave at the moment.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation for adding P2P powersave and multi-channel support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement a recv budget so that in cases of high traffic we still allow other
taskets to get processed.
Without this, we can encounter a host of issues during high wireless traffic
reception depending on system load including rcu stall's detected (ARM),
soft lockups, failure to service critical tasks such as watchdog resets,
and triggering of the tx stuck tasklet.
The same thing was proposed previously by Ben:
http://www.spinics.net/lists/linux-wireless/msg112891.html
The only difference here is that I make sure only processed packets are counted
in the budget by checking at the end of the rx loop.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a flush is requested, make sure to clear the descriptor once we've
processed it.
This resolves a hang that will occur if all RX descriptors are full when a
flush is requested.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This way it's easier to track and debug htc tx
credit issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If 20MHz CAC completed successfully then
subsequent CAC with wider bandwidth (40Mhz, 80Mhz)
with identical control frequency did not start
monitor vdev making it impossible to detect any
radar pulses during intended CAC.
It also was incorrect to assume ath10k_config() will
be called after CAC is finished. Theoretically for
non-HT channels nothing changes between CAC and
start_ap() (albeit in practice this can be
different). The incorrect assumption led to CAC
not being stopped on non-HT chandefs leading to
all Rx being drooped making it impossible for
clients to associate.
While at it clean up the code a bit.
kvalo: separate WARN_ON() from the if statement
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is done to avoid forward declarations with
upcomming patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit "ath9k: prepare for multi-interface CSA support" added a call to
ieee80211_iterate_active_interfaces in atomic context (beacon tasklet),
which is crashing.
Use ieee80211_iterate_active_interfaces_atomic instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use 0-8 instead of 0-16, which is closer to the old implementation.
Also drop the overwrite of the firstep_low parameter to improve
stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add DFS interface combination only when
CONFIG_ATH9K_DFS_CERTIFIED is set. In other case
user can run CAC/beaconing without proper handling
of pulse events (without radar detection activated).
Reported-by: Cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frame aggregation requires the IEEE80211_TX_STAT_AMPDU to
be set so that mac80211 can report the last_tx_rate correctly.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow the low level driver to make decision based
on the vif such as queues etc...
Since the vif might be NULL, we can't add it to the tracing
functions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix staging rtl8821ae driver]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible to create/delete/start/stop
monitor vdev from a few places that were not
exclusively protected against each other. This
resulted in monitor vdev being stopped/removed by
one call origin while another one was expecting it
to continue running.
For example if CAC was started and interface's
promiscuous mode was toggled monitor vdev was
removed from the driver meaning no radar would be
detected. In additional a warning would be printed
upon CAC completion complaining it tried to stop
non-running monitor vdev.
The patch simplifies monitor code by removing
IEEE80211_HW_WANT_MONITOR_VIF (which wasn't really
ever needed) and improves state tracking. It also
unifies prints.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
They were just too superfluous and made it harder to read logs. Change them to
follow the normal style used in ath10k.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As pointed out by Michal Kazior, add extra pdev stats
for 10.1 firmware.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW stats does provide the Rx rate information. Add this.
Tested with firmware 10x firmware.
Increase buffer size so more peers can be shown.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tested on 10.x firmware, and others report it at least
makes older firmware no more broken than it already was.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The filed has been missing (missmatched with FW ABI)
since 999.999.0.629 firmware release.
It's very imporatant to keep these structs up to date with FW,
due to the arithmetic we use while read the fw_stats.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since copy engine allocation has been revised the
ath10k_pci_ce_deinit() now simply zeroes copy
engine registers. It's probably a good idea to do
that before reseting for a more graceful device
reset.
Before ath10k_pci_ce_deinit() freed copy engine
ringbuffer memory so it was required to call it
after resetting. Otherwise it was possible for
device to access unmapped/freed copy engine
ringbuffer memory.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Definitions by which copy engine structure are
allocated do not change so it doesn't make much
sense to re-create those structures each time
device is booted (e.g. due to firmware recovery).
This should decrease chance of memory allocation
failures.
While at it remove per_transfer_context pointer
indirection. The array has been trailing the copy
engine ringbuffer structure anyway. This also
saves pointer size worth of bytes for each copy
engine ringbuffer.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows to use GFP_KERNEL allocation. This
should decrease chance of allocation failure, e.g.
during firmware recovery.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to debug pci problems improve the log messages in pci.c. Also
change some debug messages to warning messages to more easily catch problems.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We do not really support older firmware API 1 anymore, so better remove
MODULE_FIRMWARE() declarations for them and only list for API 2 files.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The parameter name was ath10k_target_ps, but actually it should be just
target_ps. Module parameter names should not use the ath10k_ prefix.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As cold reset is not reliable with CUS223 boards, make it possible
to disable cold reset entirely and only use warm reset. This makes it also
easier to debug warm reset problems.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_pci_wait_for_target_init() did really follow the style used elsewhere in
ath10k. Use ath10k_pci_read/write() wrappers, simplify the while loop and
improve warning messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If OTP or firmware fails to load properly, print out some
extra info in the kernel logs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Let user know the name of the board file if it is not
found, and make it easier to determine the firmware
api being used.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently there are different styles used for warning messages, unify them to
look similar. The style basically is:
1) start with a verb (if possible)
2) lower case letters
3) use plain english as much as possible
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast_2.cocci
@@
type T;
T *foo;
@@
- (T *)foo
+ foo
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
RSSI and RATES fields are valid only when START_VALID
bit is set. So, in current implementation we have to
remember/caclulate them when START_VALID and report the same
when only END_VALID is set.
Currently during heavy traffic we could have:
- 10 packets with START_VALID - correct RSSI and RATES
- 10 packets with END_VALID
- 10 packets with START_VALID - correct RSSI and RATES
- 10 packets with END_VALID
...
Next using monitor interface we will see:
- 10 packets with correct rssi/rates
- 10 packets with rssi=-95/rate=6Mbps
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce rx_status htt template instead of
stack version, as a preparation for fix
rssi and rates reporting.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Struct htt_rx_info is not needed anymore while
we will use ieee80211_rx_status structure as
a template.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove almost the same code, and do only once
__le32_to_cpu() conversion.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return error when rx_amsdu_pop() will fail.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kill rates, tsf, fcs_err, mic_err, amsdu_more, encrypt_type, signal
from htt_rx_info and setup this directly in ieee80211_rx_status.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setup band and frequency in ieee80211_rx_status
only once - for ppdu.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be used as a template, and final storage for
rx_status.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using the macro to convert the MAC address from WMI word
format to char array has lead to the wrong peer mac
address printed out while retrieving the peer stats from
FW. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Reviewed-By: Michał Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Regulatory domain settings for firmware 10.x has more options
than main firmware, so handle regulatory domain setup separately
for both supported firmwares. Fill in additional dfs domain
parameter according to current regulatory.
This patch does not solve any known bug. Not handled parameter
for firmware 10.x was found during code review.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Command WMI_FORCE_FW_HANG_CMDID is not supported in firmware 10.1.
In order to have firmware crash simulation functionality also
in firmware 10.1 driver can force firmware crash by performing not allowed
operation. Driver can deliberately crash firmware when setting vdev param for
vdev id out of range. This patch introduces two keywords to simulate_fw_crash:
'soft' which will cause firmware crash that is recoverable
by warm firmware reset but supported only in main firmware.
'hard' which will cause firmware crash recoverable by cold
firmware reset, this option works for both firmwares.
Commands to trigger firmware soft/hard crash:
echo 'soft' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash
echo 'hard' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash
kvalo: remove '\n' before checking the command and simplify how buf is null
terminated
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Don't fill this for each msdu, while this is the
same.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce ath10k_htt_rx_amsdu_allowed() function, that
group code for checking if skip amsdu packets.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When we execute otp.bin in the target check that the result it returns doesn't
contain an error. This is to make sure that we don't accidentally use invalid
calibration data.
While at it, remove the useless label in the function and add few debug messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's just cleaner to have separate argument for the parameter and result. Also
fix returned error value if response length is invalid.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When disconnecting some CID, corresponded Tx vring get released. During vring
release, all descriptors get freed. It is possible that Tx NAPI working on the same
vring simultaneously. If it happens, descriptor may be double freed.
To protect from the race above, make sure NAPI won't process the same vring.
Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if
'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI
get synchronized.
NAPI enablement status protected by wil->mutex, add protection where it was
missing and check for it.
During reset, disconnect all peers first, then proceed with the Rx vring. It allows for
the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about
connection status change
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
make sure reset flow executed in order
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use 'real' indication for hardware state.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GRO is easy to enable when already using NAPI framework,
and it improves CPU utilisation. Enable it by default.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These methods can change device state, serialize with others
similar ones like up/down
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when STA receiving connect() when already connected,
it should return error
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
upon fw error interrupt - in STA mode, disconnect/cancel scan and
then reset FW/HW
added module param - no_fw_recovery which is false by default
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wil_reset() removes vring's
At the same time NAPI may be active performing Rx/Tx completion.
If this happens, Rx/Tx polling functions going to access already removed vrings
Make sure NAPI is idle and won't be started prior to vring removal.
For this, track NAPI enabled state
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When switching between STA and AP modes, memory allocated for Rx vring leaks
This is because start_ap() allocates Rx vring but stop_ap() do not free it.
Logically, Rx vring is not valid (HW can't use it anymore), so free it in reset()
Also, check double init for Rx vring and bail out with -EINVAL
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert 2 often printed messages to dynamic ones
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure hardware to perform full reset on "power good". This mean,
reset HW on system boot. This improves card stability.
By default this is off.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put all registers in order for easier navigation;
fix naming to reflect hardware cluster
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware bug triggered by the MSI init while INTx asserted for some reason.
De-assert INTx prior to MSI set-up
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Useful to detect hardware problems
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When FW crashes, dmesg get polluted with the "FW not ready"
error message. Print it only once per FW lifecycle
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for new chip revision. Revision read from the
internal register, PCIE config's "revision id" register
do not indicate HW version properly
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce enum to describe mapping type; allow 'none' in addition to
'single' and 'page'; this is preparation for GSO
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting fragmented skb for Tx, assign skb to the last descriptor
and set number of fragments in the 1-st one
On Tx complete, HW sets "DU" bit in Tx descriptor only for the last
descriptor; so search for it using number of fragments field.
Middle descriptors may have "DU" bit not set by the hardware.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New firmware do support scan while connected. Enable it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connection established, as reported by WMI_CONNECT_EVENTID,
4-way handshaking required for the secure connection is not done
yet. It is indicated by another WMI event. Wait for it and only then
allow data traffic. In case of non-secure connection, FW reports
"data port open" immediately after connection.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers for temperature compensation need to
be programmed only for active chains. Use the TX chainmask
to make sure that this is done properly for QCA953x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Along with AR9340 and AR955x, this is also needed for
the QCA953x SoC.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we will need it to make common-beacon code work.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we will need it for ath9k_htc, may be other drivers too
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
to reduce difference between ath9k and ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On older chips, the INI value differ in similar ways as cycpwr_thr1, so
convert it to absolute values as well.
Since the ANI algorithm is different here compared to the old
implementation (fewer steps, controlled at a different point in time),
it makes sense to use values similar to what would be applied for newer
chips, just without relying on INI defaults.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The table was copied from the ANI implementation of AR9300. It assumes
that the INI values contain a baseline value that is usable as reference
from which to increase/decrease based on the noise immunity value.
On older chips, the differences are bigger and especially AR5008/AR9001
are configured to much more sensitive values than what is useful.
Improve ANI behavior by reverting to the absolute values used in the
previous implementation (expressed as a simple formula instead of the
old table).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The primary purpose of this piece of code was to selectively disable
OFDM weak signal detection. The checks for this are elsewhere, and an
earlier commit relaxed the restrictions for older chips, which are more
sensitive to interference.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unify scnprintf calls and include the current OFDM/CCK immunity level.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
qi->tqi_readyTime is written directly to registers that expect
microseconds as unit instead of TU.
When setting the CABQ ready time, cur_conf->beacon_interval is in TU, so
convert it to microseconds before passing it to ath9k_hw.
This should hopefully fix some Tx DMA issues with buffered multicast
frames in AP mode.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit 558ff225de (ath9k: fix
ps-poll responses under a-mpdu sessions) non-data frames would have
gotten a sequence number from a TIDs sequence counter instead of
using the global sequence counter.
This can lead to instable connections.
To fix this only select the correct TID if we are processing a
data frame. Furthermore, prevent non-data frames to get a sequence
number from a TID sequence counter by adding a check to
ath_tx_setup_buffer.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: reduce baseband hang detection false positive rate"
added a delay in the loop checking the baseband state, however it was
unreachable due to previous 'continue' statements.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The help text were either out of date, too small or didn't exist at all. Also
move cfg80211 dependency to ath6kl_core module as it has all the calls to
cfg80211.
Fixes checkpatch warning:
WARNING: please write a paragraph that describes the config symbol fully
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Blank lines aren't necessary before a close brace '}'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Jason noticed that with Yocto GCC 4.8.1 ath6kl crashes with this iperf command:
iperf -c $TARGET_IP -i 5 -t 50 -w 1M
The crash was:
Unable to handle kernel paging request at virtual address 1a480000
pgd = 80004000
[1a480000] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ath6kl_sdio ath6kl_core [last unloaded: ath6kl_core]
CPU: 0 PID: 1953 Comm: kworker/u4:0 Not tainted 3.10.9-1.0.0_alpha+dbf364b #1
Workqueue: ath6kl ath6kl_sdio_write_async_work [ath6kl_sdio]
task: dcc9a680 ti: dc9ae000 task.ti: dc9ae000
PC is at v7_dma_clean_range+0x20/0x38
LR is at dma_cache_maint_page+0x50/0x54
pc : [<8001a6f8>] lr : [<800170fc>] psr: 20000093
sp : dc9afcf8 ip : 8001a748 fp : 00000004
r10: 00000000 r9 : 00000001 r8 : 00000000
r7 : 00000001 r6 : 00000000 r5 : 80cb7000 r4 : 03f9a480
r3 : 0000001f r2 : 00000020 r1 : 1a480000 r0 : 1a480000
Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 6cc5004a DAC: 00000015
Process kworker/u4:0 (pid: 1953, stack limit = 0xdc9ae238)
Stack: (0xdc9afcf8 to 0xdc9b0000)
fce0: 80c9b29c 00000000
fd00: 00000000 80017134 8001a748 dc302ac0 00000000 00000000 dc454a00 80c12ed8
fd20: dc115410 80017238 00000000 dc454a10 00000001 80017588 00000001 00000000
fd40: 00000000 dc302ac0 dc9afe38 dc9afe68 00000004 80c12ed8 00000000 dc454a00
fd60: 00000004 80436f88 00000000 00000000 00000600 0000ffff 0000000c 80c113c4
fd80: 80c9b29c 00000001 00000004 dc115470 60000013 dc302ac0 dc46e000 dc302800
fda0: dc9afe10 dc302b78 60000013 dc302ac0 dc46e000 00000035 dc46e5b0 80438c90
fdc0: dc9afe10 dc302800 dc302800 dc9afe68 dc9afe38 80424cb4 00000005 dc9afe10
fde0: dc9afe20 80424de8 dc9afe10 dc302800 dc46e910 80424e90 dc473c00 dc454f00
fe00: 000001b5 7f619d64 dcc7c830 00000000 00000000 dc9afe38 dc9afe68 00000000
fe20: 00000000 00000000 dc9afe28 dc9afe28 80424d80 00000000 00000035 9cac0034
fe40: 00000000 00000000 00000000 00000000 000001b5 00000000 00000000 00000000
fe60: dc9afe68 dc9afe10 3b9aca00 00000000 00000080 00000034 00000000 00000100
fe80: 00000000 00000000 dc9afe10 00000004 dc454a00 00000000 dc46e010 dc46e96c
fea0: dc46e000 dc46e964 00200200 00100100 dc46e910 7f619ec0 00000600 80c0e770
fec0: dc15a900 dcc7c838 00000000 dc46e954 8042d434 dcc44680 dc46e954 dc004400
fee0: dc454500 00000000 00000000 dc9ae038 dc004400 8003c450 dcc44680 dc004414
ff00: dc46e954 dc454500 00000001 dcc44680 dc004414 dcc44698 dc9ae000 dc9ae030
ff20: 00000001 dc9ae000 dc004400 8003d158 8003d020 00000000 00000000 80c53941
ff40: dc9aff64 dcb71ea0 00000000 dcc44680 8003d020 00000000 00000000 00000000
ff60: 00000000 80042480 00000000 00000000 000000f8 dcc44680 00000000 00000000
ff80: dc9aff80 dc9aff80 00000000 00000000 dc9aff90 dc9aff90 dc9affac dcb71ea0
ffa0: 800423cc 00000000 00000000 8000e018 00000000 00000000 00000000 00000000
ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<8001a6f8>] (v7_dma_clean_range+0x20/0x38) from [<800170fc>] (dma_cache_maint_page+0x50/0x54)
[<800170fc>] (dma_cache_maint_page+0x50/0x54) from [<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c)
[<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c) from [<80017238>] (arm_dma_map_page+0x64/0x68)
[<80017238>] (arm_dma_map_page+0x64/0x68) from [<80017588>] (arm_dma_map_sg+0x7c/0xf4)
[<80017588>] (arm_dma_map_sg+0x7c/0xf4) from [<80436f88>] (sdhci_send_command+0x894/0xe00)
[<80436f88>] (sdhci_send_command+0x894/0xe00) from [<80438c90>] (sdhci_request+0xc0/0x1ec)
[<80438c90>] (sdhci_request+0xc0/0x1ec) from [<80424cb4>] (mmc_start_request+0xb8/0xd4)
[<80424cb4>] (mmc_start_request+0xb8/0xd4) from [<80424de8>] (__mmc_start_req+0x60/0x84)
[<80424de8>] (__mmc_start_req+0x60/0x84) from [<80424e90>] (mmc_wait_for_req+0x10/0x20)
[<80424e90>] (mmc_wait_for_req+0x10/0x20) from [<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio])
[<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio]) from [<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio])
[<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio]) from [<8003c450>] (process_one_work+0x10c/0x370)
[<8003c450>] (process_one_work+0x10c/0x370) from [<8003d158>] (worker_thread+0x138/0x3fc)
[<8003d158>] (worker_thread+0x138/0x3fc) from [<80042480>] (kthread+0xb4/0xb8)
[<80042480>] (kthread+0xb4/0xb8) from [<8000e018>] (ret_from_fork+0x14/0x3c)
Code: e1a02312 e2423001 e1c00003 f57ff04f (ee070f3a)
---[ end trace 0c038f0b8e0b67a3 ]---
Kernel panic - not syncing: Fatal exception
Jason's analysis:
"The GCC 4.8.1 compiler will not do the for-loop till scat_entries, instead,
it only run one round loop. This may be caused by that the GCC 4.8.1 thought
that the scat_list only have one item and then no need to do full iteration,
but this is simply wrong by looking at the assebly code. This will cause the sg
buffer not get set when scat_entries > 1 and thus lead to kernel panic.
Note: This issue not observed with GCC 4.7.2, only found on the GCC 4.8.1)"
Fix this by using the normal [0] style for defining unknown number of list
entries following the struct. This also fixes corruption with scat_q_depth, which
was mistankely added to the end of struct and overwritten if there were more
than item in the scat list.
Reported-by: Jason Liu <r64343@freescale.com>
Tested-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add recalculation of RTS/CTS protection when one or more legacy
stations are connected to ath10k. In this case enable RTS/CTS
protection and set sw retry profile are needed in the FW.
Without this change legacy station is starved and has very low
throughput.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
IBSS mode requires the changing of supported rate. Do this
by reassociate the peer. The investigation shows that if move
from legacy to HT, the rate control won't work after changing
the supported rate. But once changing the supported rate to HT,
user can assign the TxRate in HT mode.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Seems like we have an old bug, where we incidently overwrites
the max_antenna_gain we pass to firmware, with zero value.
End of all we are artifically reducing the output power.
This patch removes the excessive assignment on max_antenna_gain,
which is being provided by regulatory domain, and consequently
improves the tx power.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Consolidate the list of msdu skbs into the msdu-head skb, delete the
rest of the skbs, pass the msdu-head skb on up the stack as normal.
Tested with high-speed TCP and UDP traffic on modified firmware that
supports raw-rx.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch suggests to propagate error code from wil_find_cid(), and, indeed,
it is a good idea.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wrong index comparison logic, found by smatch:
drivers/net/wireless/ath/wil6210/debugfs.c:402 wil_txdesc_debugfs_show() warn: buffer overflow 'wil->vring_tx' 24 <= 24
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Older chipsets are more sensitive to high PHY error counts, and the
current noise immunity thresholds were based on tests run at QCA with
newer chipsets.
This patch brings back the values from the old ANI implementation for
old chipsets, and it also disables weak signal detection on an earlier
noise immunity level, to improve overall radio stability on affected
devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 80b4205b "ath9k: Fix OFDM weak signal detection for AP mode"
prevented weak signal detection changes from taking effect in AP mode on
all chipsets, claiming it is "not allowed".
The main reason for not disabling weak signal detection in AP mode is
that typically beacon RSSI is used to track whether it is needed to
boost range, and this is unavailable in AP mode for obvious reasons.
The problem with not disabling weak signal detection is that older
chipsets are very sensitive to high PHY error counts. When faced with
heavy noise, this can lead to an excessive amount of "Failed to stop
TX DMA" errors in the field.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to 802.11n-2012 standard in paragraph PPDU Fromat(20.3.2) HT-mixed
format Hearder PPDU contains : L_STF, L_LTF, L_SIG, HT_SIG, HT_STF, HT_LTF
they are symbols in the preamble, there are in time unit(us) that's for why
it can't be computed in bytes
Signed-off-by: Sylvain ROGER RIEUNIER <sylvain.roger.rieunier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using multiple vdevs (stations, aps, etc), it is
nice to be able to associate log messages with specific
interfaces. So, add vdev-id to most logging messages.
Add return code as well, where it was missing.
kvalo: unify some of the messages to follow the same style
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Groupcast frames are not subject for BACK reordering because they are not
ACK'ed and one can't request re-transmitt
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
implement del_station() method in the struct cfg80211_ops
It allows to disconnect single peer from the AP
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When notifying about Rx mgmt (ex: during scan), extract
signal strength reported by the hardware.
signal is not MBM, it is arbitrary units 0..100
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to fill translation table before calling WMI with WMI_VRING_CFG_CMDID
since firmware may generate events during this call; and events need translation
table filled to be properly dispatched
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disconnect event reported by the FW, should lead to disconnection
of only requested peer. Find for the appropriate CID and disconnect
only it
For AP-like interface, notify cfg80211 with del_sta(),
for the client type interface, disconnect and turn link off.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calculate statistics per connection, report with "iw station dump"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx stats is not calculated per STA - just give some number
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When FW notifies about BACK status change, it provides ring ID.
Process BA status for requested connection only. As for now, FW
don't report Rx BACK status, it reports Tx one instead.
As per current algorithm used in the firmware, imply Rx BACK
state is in sync with Tx one
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware do not support "real" broadcast on the air.
Use method similar to the Directed Multicast Service (DMS) as
described in the 10.23.15.2 "DMS procedures"
This service copies frame and delivers unicast for each associated peer
Do the following: send original frame to 1-st Tx vring, and send copies
to all other active vrings.
As currently hardware/firmware don't support A-MSDU, convert broadcast
frame to unicast instead of wrapping it in A-MSDU
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are 24 possible Tx vrings; when doind multiple connections, more then
one vring has to be used. Search for free one and select it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running multiple connections, hardware can't do BACK reordering
and it should be done on the host.
Model after mac80211's implementation. Drop RCU for now;
to be re-added when BACK will be stabilized
BACK handshaking is not implemented yet in the hardware,
pretend it was done to support the way FW operating
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable multiple (up to 8 - HW/FW limitation) simultaneous connections.
Each connection has its own CID (connection ID) that describes chip's
beam-forming entity. Tx Vring should refer to correct CID for frame to reach
its destination.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print '_' for the 'idle' descriptors - this makes vring representation more visible.
Also, for the Tx side, differentiate descriptors having associated skb's - print ones
with skb as 'H' and without as 'h'. Good to represent scattered frames.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expand debug capabilities to query all Tx/Rx descriptors. Usefull to analyse
various hardware/software stall situations. Printed is whole descriptor content
and the frame itself.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement management frame passing. In order to receive frame on the other
side, remain_on_channel() should be implemented as well
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_setup_ht_cap
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_init_channels_rates.
sbands are move to ath_common as well.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't make much sense to calculate the ring
size fill count because it already is memoized in
a separate variable.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One of the premises was to guarantee serialized
completion handling for upper layers
(HTC/WMI/HTT). Since quite some time now it is no
longer necessary.
The other premise was to batch up tx/rx
completions to take advantage of hot caches.
However frame tx/rx completion indications come in
on a single pipe already so they are already
batched up. More meaningful batching is done in
HTT itself.
This means PCI completion is no longer necessary
to keep around. It just wastes memory, cycles and
SLOC.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is inefficient to grab irqsave spinlocks for
skb lists for each queue/dequeue action.
Using rx_ring.lock and tx_lock allows to use less
heavy bh spinlock functions and moving locking
upwards allows to toggle spinlocks less often.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT Rx endpoint processes both frame rx
indications and frame tx completion indications.
Those completions typically come in batches and
may be mixed so it makes sense to defer processing
hoping to get a bunch of them and take advantage
of hot caches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Going through full htc tx path for htt tx is a
waste of resources. By skipping it it's possible
to easily submit scatter-gather to the pci hif for
reduced host cpu load and improved performance.
The new approach uses dma pool to store the
following metadata for each tx request:
* msdu fragment list
* htc header
* htt tx command
The htt tx command contains a msdu prefetch.
Instead of copying it original mapped msdu address
is used to submit a second scatter-gather item to
hif to make a complete htt tx command.
The htt tx command itself hands over dma mapped
pointers to msdus and completion of the command
itself doesn't mean the frame has been sent and
can be unmapped/freed. This is why htc tx
completion is skipped for htt tx as all tx related
resources are freed upon htt tx completion
indication event (which also implicitly means htt
tx command itself was completed).
Since now each htt tx request effectively consists
of 2 copy engine items CE_HTT_H2T_MSG_SRC_NENTRIES
is updated to allow maximum of
TARGET_10X_NUM_MSDU_DESC msdus being queued. This
keeps the tx path resource management simple.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
PCI is capable of handling scatter-gather lists.
This can be used to avoid copying memory.
Change the name of the callback while at to
reflect its purpose.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The flag wasn't used anymore. No need to keep it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no real benefit from using them. DMA-API
already provides debugging. Some skbuffs are
already mapped directly with DMA-API since wrapper
arguments were insufficient and extending them
would be pointless.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After we pass frames with INV_PEER to upper layer in commit 716ae53c56
("ath10k: pass frames with invalid peer status to upper layer") we could pass
some management frames (in case INVALID_PEER and MGMT_CTRL) twice to upper
layer, once via WMI and once via HTT. Next we could handle assoc request twice.
This patch remove such regression.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Indicate spectrum management support in hardware
flags, while we already handle power set
(IEEE80211_CONF_CHANGE_POWER) in the ath10k driver.
This enable 802.11h support for station mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Retrieve the mactime of ieee80211_rx_status based on received
data frame. The value is obtained from the htt_rx_indication_ppdu
structure and only available in 32-bit.
kvalo: white space fixes
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The arsta structure wasn't initialized for
non-ap interfaces. This should fix related
warnings/crashes.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The nwifi header is padded to 4 bytes. This wasn't
a problem until one tried to (at least) rx 4addr
frames.
This finally allows managed iface to be used in a
bridge.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes it easier to determine why some failures
happened.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Implement the get TSF by simply returning 0 so that IBSS
merging is happening. Otherwise, IBSS nodes that have similar
SSID naming won't merge. This is simply fooling the mac80211
that the TSF in the received beacon is higher than the local TSF.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only set sc->rx.discard_next to rx_stats->rs_more when actually
discarding the current descriptor.
Also, fix a detection of broken descriptors:
First the code checks if the current descriptor is not done.
Then it checks if the next descriptor is done.
Add a check that afterwards checks the first descriptor again, because
it might have been completed in the mean time.
This fixes a regression introduced in
commit 723e711356
"ath9k: fix handling of broken descriptors"
Cc: stable@vger.kernel.org
Reported-by: Marco André Dinis <marcoandredinis@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if the baseband state remains stable, and add a small delay
between register reads.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only one channel is returned - the one currently being used.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some chips, baseband watchdog hangs are more common than others, and
the driver has support for handling them.
Interrupts even after a watchdog hang are also quite common, so there's
not much point in spamming the user's logfiles.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
5/10 MHz channel bandwidth is configured via the PLL clock, instead of
the AR_PHY_MODE register. Using that register is AR93xx specific, and
makes the mode incompatible with earlier chipsets.
In some early versions, these flags were apparently applied at the wrong
point in time and thus did not cause connectivity issues, however now
they are causing problems, as pointed out in this OpenWrt ticket:
https://dev.openwrt.org/ticket/14916
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivially reduces text size too.
$ size drivers/net/wireless/ath/ath9k/debug.o*
text data bss dec hex filename
34436 2528 5128 42092 a46c drivers/net/wireless/ath/ath9k/debug.o.new
34464 2528 5128 42120 a488 drivers/net/wireless/ath/ath9k/debug.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of MAC hangs and stuck beacons were missing
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 handles the actual operations, so ath9k can just indicate
support for this. Based on initial tests, this combination seems to
work fine.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When passing tx frames to the U-APSD queue for powersave poll responses,
the ath_atx_tid pointer needs to be passed to ath_tx_setup_buffer for
proper sequence number accounting.
This fixes high latency and connection stability issues with ath9k
running as AP and a few kinds of mobile phones as client, when PS-Poll
is heavily used
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The minimum CCA power threshold values have to be adjusted
for existing cards to be in compliance with new regulations.
Newer cards will make use of the values obtained from EEPROM,
support for this was added earlier. To make sure that cards
that are already in use and don't have proper values in EEPROM,
do not violate regulations, use the initvals instead.
Cc: stable@vger.kernel.org
Reported-by: Jeang Daniel <dyjeong@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: wil6210@qca.qualcomm.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows dynamic changes of bandwidth/nss/smps,
e.g. via ht/vht operation mode change
notification.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware ignores SMPS flags in peer assoc command.
For SMPS to work it is necessary to set peer
parameter after peer assoc command so that tx
chainmask is setup properly.
This should fix packet loss and improve throughput
with stations that have SMPS enabled upon
association.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I modified Michal's commit c930f744bd ("ath10k: implement channel switching") to return
when vdev_start() fails, but forgot to release conf_mutex.
Found by coccinelle:
>> drivers/net/wireless/ath/ath10k/mac.c:2745:5-11: preceding lock on line 2663
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes a checkpatch warning in ath10k:
drivers/net/wireless/ath/ath10k/mac.c:1636: WARNING: Avoid CamelCase: <regpair->regDmnEnum>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix a checkpatch warning:
drivers/net/wireless/ath/ath10k/debug.h:95: CHECK: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dtim period sent to FW was 0 because the dtim period
was never set. This caused an incorrect dtim count to be sent in
beacons.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes problems seen with multiple softap clients and reconnecting
softap clients.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more line with the names of the other members
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3680 has a few registers on other addresses.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After fw caps exchange, print the FW's capabilities.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If wowlan if off mac80211 will stop / start the driver on suspend /
resume. This causes problems on resume since request_firmware is called
from start. Fix this by caching the nv.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some wcnss firmwares the start command can take up to 300ms to
complete. Currently there is a 200ms timeout for SMD command to
complete which causes the start to fail.
Increase the timeout to 500ms. Also improve debug information
regarding SMD command completion time.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Response format is not in the canonical format.
wcn36xx_smd_rsp_status_check cannot be used.
* Save the FW caps in wcn36xx struct for later use.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the original code we shift "AR5K_PHY(256) >> 28" which is zero but
the intent was to shift the return value of ath5k_hw_reg_read() like we
do a couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As result deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case IRQ configuration is unknown possibly enabled MSIs
are left enabled in ath10k_pci_deinit_irq(). This update
fixes the described misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The documentation states that pci_enable_msi_block() returns the number of
requests 'could have been allocated', not 'could allocate'. IOW, MSIs are *not*
enabled if a positive value returned.
kvalo: add commit log based on Alexander's email
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass frames with invalid peer status to upper layer.
Next mac80211 will validate frames and drop if required.
This is required to detect spurious frames and pass
this info to user mode (detect CLASS2 CLASS3 frames from
nonauthenticated/nonassociated stations).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is a workaround for HT-enabled STAs which break the spec
and have no HT capabilities RX mask (no HT RX MCS map).
As per spec, in section 20.3.5 Modulation and coding scheme (MCS),
MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs.
Firmware asserts if such situation occurs.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.
This patch depends on
ath10k: fix device initialization routine
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware CUS232 version 2 has some issues with cold
reset that lead to Data Bus Errors or system hangs
in some cases. It's safer to use warm reset when
possible as it shouldn't trigger the
aforementioned issues.
Prefer warm reset over cold reset. However since
warm reset doesn't work after FW crash make sure to
fallback to cold reset when booting up the HW.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was found during testing the nss calculation does not
cover all corner cases. Station could request eq. only MCS8
and MCS9 (nss=2 specific). Next num_rates=2 so the driver
sets nss=(max((2+7)/8, 1))=1. Which is wrong. The in-driver
calculation was introduced prior (commit ddcc347b70
mac80211: fix rx_nss calculation for drivers with hw rc).
Since it's fixed, use mac80211 provided value from now.
End user will experience lower throuhputs than expected
if the nss is wrongly calculated.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This throw a lot of pointless warnings in case of DFS (radar
detection) and PHYERR events from firmware, when firmware may
actually insert more data, than we assume.
Besides of being noisy this debug does not protect or check
anything usefull currently. It was introduced long time ago
while debugging aggregations. So just removing it.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Show message length and expected length. Helps debug
firmware mismatch issues.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds a routine to calculate the median IQ correction
values for AR955x, which is used for outlier detection.
The normal method which is used for all other chips is
bypassed for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used for storing data for mutiple
IQ calibration runs, for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration post-processing for AR955x is different
from other chips - instead of just doing it as part
of AGC calibration once, it is triggered 3 times and
a median is determined. This patch adds initial support
for changing the calibration behavior for AR955x.
Also, to simplify things, a helper routine to issue/poll
AGC calibration is used.
For non-AR955x chips, the iqcal_idx (which will be used
in subsequent patches) is set to zero.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect values are programmed in the registers
containing the IQ correction coefficients by the IQ-CAL
post-processing code. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ar9003_hw_tx_iq_cal_outlier_detection instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In chips like AR955x, the initvals contain the information
whether IQ calibration is to be done in the HW when an
AGC calibration is triggered. Check if IQ-CAL is enabled
in the initvals before flagging 'txiqcal_done' as true.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration data is not reused for SoC chips, so
call ar9003_hw_tx_iq_cal_post_proc() with the correct
argument. The 'is_reusable' flag is currently used
only for PC-OEM chips, but it makes things clearer to
specify it explicity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Buffalo WLI-UV-AG300P is almost the same as Sony UWA-BR100.
Signed-off-by: Masaki TAGAWA <masaki@club.kyutech.ac.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no benefit in retaining the legacy rate control module
in the driver codebase.
It is known to be buggy and has less than optimal performance
in real-world environments compared with minstrel. The only
reason that it was kept when we made the switch to minstrel
as default was that it showed higher throughput numbers in a
clean/ideal environment.
This is no longer the case and minstrel can push ath9k to
the same throughput levels. In TCP, with 3-stream cards, more than
295 Mbps can be obtained in open air, with 2-stream cards,
210 Mbps is easily reached. To test performance issues,
instead of using a broken rate control module, it is better
to use the fixed-rate interface provided by mac80211 anyway.
The ath9k RC has not received any bug fixes in years and is
just bit-rotting away - this patch removes it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
after switch to common fucntions we do not need this memcpy any more.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_rx_skb_postprocess. We will use it
on ath9k_htc.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can reuse this function in ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can reuse this fucntion on ath9k_htc.
Now we will need to use common version last_rssi, so switch
it too.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we need access to this variable from common functions.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_has_tx_pending’:
drivers/net/wireless/ath/ath9k/main.c:1869: warning: ‘npend’ may be used uninitialized in this function
Introduced by commit 10e2318103 ("ath9k:
optimize ath9k_flush").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix IQ calibration" added a check
to ensure that valid i2_p_q2_a0_d1 values are not discarded.
But since it is masked with 0xfff earlier, the codepath
will not be executed.
The earlier case where all values above 0x800 were considered
invalid is incorrect, since the HW can return valid values
between 0x800 and 0xfff.
Cc: Kai Shi <kaishi@qca.qualcomm.com>
Reported-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Soon mac80211 will support multi-interface CSA so
using sc->csa_vif is not an option.
Instead just depend on vif->csa_active. Calling
ieee80211_csa_finish() multiple number of times
should not be an issue.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_rx_status.flags is full. Define a new vht_flag
variable to be able to set more VHT related flags and make
room in flags.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath10k]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The purpose of this housekeeping is to make some room for
VHT flags. The radiotap vendor fields weren't in use.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving an IBSS_JOINED event select the BSS object
based on the {bssid, channel} couple rather than the bssid
only.
With the current approach if another cell having the same
BSSID (but using a different channel) exists then cfg80211
picks up the wrong BSS object.
The result is a mismatching channel configuration between
cfg80211 and the driver, that can lead to any sort of
problem.
The issue can be triggered by having an IBSS sitting on
given channel and then asking the driver to create a new
cell using the same BSSID but with a different frequency.
By passing the channel to cfg80211_get_bss() we can solve
this ambiguity and retrieve/create the correct BSS object.
All the users of cfg80211_ibss_joined() have been changed
accordingly.
Moreover WARN when cfg80211_ibss_joined() gets a NULL
channel as argument and remove a bogus call of the same
function in ath6kl (it does not make sense to call
cfg80211_ibss_joined() with a zero BSSID on ibss-leave).
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Cc: libertas-dev@lists.infradead.org
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[minor code cleanup in ath6kl]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scheduled scan matchsets were intended to be a list of filters,
with the found BSS having to pass at least one of them to be passed
to the host. When the RSSI attribute was added, however, this was
broken and currently wpa_supplicant adds that attribute in its own
matchset; however, it doesn't intend that to mean that anything
that passes the RSSI filter should be passed to the host, instead
it wants it to mean that everything needs to also have higher RSSI.
This is semantically problematic because we have a list of filters
like [ SSID1, SSID2, SSID3, RSSI ] with no real indication which
one should be OR'ed and which one AND'ed.
To fix this, move the RSSI filter attribute into each matchset. As
we need to stay backward compatible, treat a matchset with only the
RSSI attribute as a "default RSSI filter" for all other matchsets,
but only if there are other matchsets (an RSSI-only matchset by
itself is still desirable.)
To make driver implementation easier, keep a global min_rssi_thold
for the entire request as well. The only affected driver is ath6kl.
I found this when I looked into the code after Raja Mani submitted
a patch fixing the n_match_sets calculation to disregard the RSSI,
but that patch didn't address the semantic issue.
Reported-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's not a single rate control algorithm actually in
a separate module where the module refcount would be
required. Similarly, there's no specific rate control
module.
Therefore, all the module handling code in rate control
is really just dead code, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the code to allow making all the rate control ops
const, nothing ever needs to change them. Also change all
drivers to make use of this and mark the ops const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit, "ath9k_hw: Fix incorrect Tx control power in AR9003 template"
fixed the incorrect values in the eeprom templates, but if
boards have already been calibrated with incorrect values,
they would still be using the wrong TX power. Fix this by assigning
a default value in such cases.
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 ->sta_rc_update() callback must be atomic. Since we have to
take mutex and do other operations that can sleep when sending fimrware
commands to device, the only option to satisfy atomicity requirement of
->sta_rc_update(), that I can see, is introduce work_struct and defer
uploading new rates to that work.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Raw id and FW id should be switched.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is a copy/paste of patch provided by Sujith for ath9k.
"Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter."
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
