With IPv4 and IPv6 now using the same format for checksums based on the
length of the frame we need to update the i40e and i40evf drivers so that
they correctly account for lengths greater than or equal to 64K.
With this patch the driver should now correctly update checksums for frames
up to 16776960 in length which should be more than large enough for all
possible TSO frames in the near future.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Media Not Available flag to the link event mask. It seems
that event comes first if you have a DA cable pulled out, but there's no
follow-up event for Link Down; if you're not looking for MEDIA_NA you will
get no event, even though there's now no Link.
Change-ID: cb3340a2849805bb881f64f6f2ae810eef46eba7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These conditions can happen any time VFs are enabled or disabled and are
not really indicative of fatal problems unless they happen continuously.
Lower the log level so that people don't get scared.
Change-ID: I1ceb4adbd10d03cbeed54d1f5b7f20d60328351d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
100baseT/Full is now listed and supported link mode for 10GBaseT PHY.
This is a fix to list all the supported link modes of 10GBaseT PHY.
Change-ID: If2be3212ef0fef85fd5d6e4550c7783de2f915e9
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were passing in the seed where we should just be passing false
because we want the VSI table not the pf table.
Change-ID: I9b633ab06eb59468087f0c0af8539857e99f9495
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Periodic link polling was added when the link events were found not to be
trustworthy. This was the case early on, but was likely because the link
event mask was being used incorrectly. As this has been fixed in recent
code, we can disable the link polling to lessen the AQ traffic.
Change-ID: Id890b5ee3c2d04381fc76ffa434777644f5d8eb0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Upon module remove, wait a little longer after requesting a reset before
checking to see if the firmware responded. This change prevents double
resets when the firmware is busy.
Change-ID: Ieedc988ee82fac1f32a074bf4d9e4dba426bfa58
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the VFLR bit immediately after triggering a reset instead of
waiting until after cleanup is complete. Make sure to trigger a reset
every time, not just if the PF is up.
These changes fix a problem where VF resets would get lost by the PF,
preventing the VF driver from initializing.
Change-ID: I5945cf2884095b7b0554867c64df8617e71d9d29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new device ID is 0x37D3 and it should follow the same flows and
branding string as for 0x37D0.
Change-ID: Ia5ad4a1910268c4666a3fd46a7afffbec55b4fc2
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Users of ethtool were being given the mistaken impression that this
driver was able to change its VLAN tagging features, and were
disappointed that this was not actually the case. Implement
ndo_fix_features method so that we can adjust these flags as needed to
avoid false impressions.
Change-ID: I08584f103a4fa73d6a4128d472e4ef44dcfda57f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This variable is vestigial, a remnant of the primordial code from which
this driver spawned. We can safely remove it.
Change-ID: I24e0fe338e7c7c50d27dc5515564f33caefbb93a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables the Capability for XL710/X710 devices with FW API
version higher than 1.4 to do geneve Rx offload.
Change-ID: I9a8f87772c48d7d67dc85e3701d2e0b845034c0b
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
active_vlans is an unsigned long array, hence a null check on this
array is superfluous and can be removed.
Detected with static analysis by smatch:
drivers/net/ethernet/intel/i40e/i40e_debugfs.c:386
i40e_dbg_dump_vsi_seid() warn: this array is probably
non-NULL. 'vsi->active_vlans'
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82544 has code that adds one additional descriptor per data buffer.
However we weren't taking that into account when determining the descriptors
needed for the next transmit at the end of the xmit_frame path.
This change takes that into account by doubling the number of descriptors
needed for the 82544 so that we can avoid a potential issue where we could
hang the Tx ring by loading frames with xmit_more enabled and then stopping
the ring without writing the tail.
In addition it adds a few more descriptors to account for some additional
workarounds that have been added over time.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current code path is capable of grossly overestimating the number of
descriptors needed to transmit a new frame. This specifically occurs if
the skb contains a number of 4K pages. The issue is that the logic for
determining the descriptors needed is ((S) >> (X)) + 1. When X is 12 it
means that we were indicating that we required 2 descriptors for each 4K
page when we only needed one.
This change corrects this by instead adding (1 << (X)) - 1 to the S value
instead of adding 1 after the fact. This way we get an accurate descriptor
needed count as we are essentially doing a DIV_ROUNDUP().
Reported-by: Ivan Suzdal <isuzdal@mirantis.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was an error introduced with commit 3fced53507 ("i40e: X722 is
on the IOSF bus and does not report the PCI bus info"), where code was
added but the enabling flag is never set.
CC: Anjali Singhai Jain <anjali.singhai@intel.com>
CC: Stefan Assman <sassman@redhat.com>
Fixes: 3fced53507 ("i40e: X722 is on the IOSF bus ...")
Reported-by: Steve Best <sbest@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-04-05
This series contains updates to i40e and i40evf only.
Stefan converts dev_close() to ndo_stop() for ethtool offline self test,
since dev_close() causes IFF_UP to be cleared which will remove the
interface routes and addresses.
Alex bumps up the size of the transmit data buffer to 12K rather than 8K,
which provides a gain in throughput and a reduction in overhead for
putting together the frame. Fixed an issue in the polling routines where
we were using bitwise operators to avoid the side effects of the
logical operators. Then added support for bulk transmit clean for skbs.
Jesse fixed a sparse issue in the type casting in the transmit code and
fixed i40e_aq_set_phy_debug() to use i40e_status as a return code.
Catherine cleans up duplicated code.
Shannon fixed the cleaning up of the interrupt handling to clean up the
IRQs only if we actually got them set up. Also fixed up the error
scenarios where we were trying to remove a non-existent timer or
worktask, which causes the kernel heartburn.
Mitch changes the notification of resets to the reset interrupt handler,
instead of the actual reset initiation code. This allows the VFs to get
properly notified for all resets, including resets initiated by different
PFs on the same physical device. Also moved the clearing of VFLR bit
after reset processing, instead of before which could lead to double
resets on VF init. Fixed code comment to match the actual function name.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The fm10k driver used its own code for generating a default indirection
table on device load, which was not the same as the default generated by
ethtool when indir_size of 0 is passed to SRXFH. Take advantage of
ethtool_rxfh_indir_default() and simplify code to write the redirection
table to reduce some code duplication.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
s/funciton/function to resolve a typo, and cleanup grammar on a few
comments regarding processing the VF mailboxes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If 'attr_flag < (1 << (2 * FM10K_TEST_MSG_NESTED))' is ever false, err
will be used uninitialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce duplicate code and the amount of indentation by adding
fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help
add fm10k_stat structures to the ethtool stats callbacks. This helps
increase ease of use for future stat additions, and increases code
readability. Skip handling of the per-queue stats as these will be
reworked in a following patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During fm10k_io_error_detected we were clearing the interrupt scheme
before we freed the MBX IRQ. This causes a kernel panic because the MBX
IRQ are assigned after MSI-X initialization. Clearing the interrupt
scheme results in removing the MSI-X entry table. Fix this by freeing
the MBX IRQ before we clear the interrupt scheme, as we do elsewhere in
the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
fm10k_stop_hw_generic calls fm10k_disable_queues_generic, which may
return an error code indicating that the queues were not stopped within
the time limit. Notify the user by displaying a message in the kernel
message ring, in a similar way to how we notify the user when reset_hw
fails. There isn't much we can do to recover from this error, so
currently nothing else is done.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In fm10k_set_num_queues, we previously assigned the base template. This
would always be overwritten by either fm10k_set_qos_queues or
fm10k_set_rss_queues. In either case, we don't need the base values, so
we can just remove them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the C standard dereferencing a variable before it is
checked invokes undefined behavior, and thus compilers are free to
assume the check for NULL isn't necessary. Prevent this by re-ordering
the NULL check of msix_entries in fm10k_free_mbx_irq.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup the remaining instances of using memcpy() instead of the preferred
ether_addr_copy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to crash the kernel in this instance so just warn about the
condition and play on.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use BIT() macro instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The semantic patch that makes this change is available
in scripts/coccinelle/misc/compare_const_fl.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Minor correction in the comment to reflect the correct function name
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver happens to read a register during the time in which the
device is undergoing reset, it will receive a value of 0xdeadbeef
instead of a valid value. Unfortunately, the driver may misinterpret
this as a valid value, especially if it's just looking for individual
bits.
Add an explicit check for this value when we are looking for admin queue
errors, and trigger reset recovery if we find it.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no real error in an unknown event from the Firmware, we're just
posting a useful FYI notice, so this patch simply removes the "Error" word.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the VFLR bit after reset processing, instead of before. This
prevents double resets on VF init.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Notify VFs in the reset interrupt handler, instead of the actual
reset initiation code. This allows the VFs to get properly notified for
all resets, including resets initiated by different PFs on the same
physical device.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some error scenarios, we may find ourselves trying to remove a
non-existent timer or worktask. This causes the kernel some bit
of consternation, so don't do it.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When dropping into debug mode in a failed probe, make sure that
the AdminQ is left alive for possible hand debug of driver and
firmware states.
Move the mutex_init calls earlier in probe so that if init fails,
the admin queue interface is still available for debugging purposes.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When cleaning up the interrupt handling, clean up the IRQs only if
we actually got them set up. There are a couple of error recovery
paths that were violating this and causing the kernel a bit of
indigestion.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_common.c typically uses i40e_status as a return code,
but got missed this one case.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When updating a VSI, save off the number of allocated and unallocated
VSIs as we do when adding a VSI.
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the duplicate definition of I40E_MAX_USER_PRIORITY
in i40e.h that is not needed.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Simple cast to fix a sparse warning.
Fixes: commit 5453205cd0 ("i40e/i40evf: Enable support for
SKB_GSO_UDP_TUNNEL_CSUM")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables bulk Tx clean for skbs. In order to enable it we need
to pass the napi_budget value as that is used to determine if we are truly
running in NAPI mode or if we are simply calling the routine from netpoll
with a budget of 0. In order to avoid adding too many more variables I
thought it best to pass the VSI directly in a fashion similar to what we do
on igb and ixgbe with the q_vector.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the polling routines for i40e and i40evf we were using bitwise operators
to avoid the side effects of the logical operators, specifically the fact
that if the first case is true with "||" we skip the second case, or if it
is false with "&&" we skip the second case. This fixes an earlier patch
that converted the bitwise operators over to the logical operators and
instead replaces the entire thing with just an if statement since it should
be more readable what we are trying to do this way.
Fixes: 1a36d7fadd ("i40e/i40evf: use logical operators, not bitwise")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The only error case is when the malloc fails, in which case the clean up
loop does nothing at all, so remove it
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
From what I can tell the practical limitation on the size of the Tx data
buffer is the fact that the Tx descriptor is limited to 14 bits. As such
we cannot use 16K as is typically used on the other Intel drivers. However
artificially limiting ourselves to 8K can be expensive as this means that
we will consume up to 10 descriptors (1 context, 1 for header, and 9 for
payload, non-8K aligned) in a single send.
I propose that we can reduce this by increasing the maximum data for a 4K
aligned block to 12K. We can reduce the descriptors used for a 32K aligned
block by 1 by increasing the size like this. In addition we still have the
4K - 1 of space that is still unused. We can use this as a bit of extra
padding when dealing with data that is not aligned to 4K.
By aligning the descriptors after the first to 4K we can improve the
efficiency of PCIe accesses as we can avoid using byte enables and can fetch
full TLP transactions after the first fetch of the buffer. This helps to
improve PCIe efficiency. Below is the results of testing before and after
with this patch:
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
Before:
87380 16384 16384 10.00 33682.24 20.27 -1.00 0.592 -1.00
After:
87380 16384 16384 10.00 34204.08 20.54 -1.00 0.590 -1.00
So the net result of this patch is that we have a small gain in throughput
due to a reduction in overhead for putting together the frame.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can use the ethtool rx-vlan-filter flag to
toggle Rx VLAN filtering on and off. This is basically just an extension
of the existing VLAN promisc work in that it just adds support for the
additional ethtool flag.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added support to match on UDP fields in the transport layer.
Extended core logic to support multiple headers.
Verified with the following filters :
handle 1: u32 divisor 1
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
u32 ht 1: order 2 \
match tcp src 1024 ffff match tcp dst 23 ffff action drop
handle 2: u32 divisor 1
u32 ht 800: order 3 link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 17 ff
u32 ht 2: order 4 \
match udp src 1025 ffff match udp dst 24 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible on some HW that a system reset could occur when we are
holding the SWFW semaphore lock. So next time the driver was loaded we
would see it incorrectly as locked. This patch will recover from that state
by: Attempting to acquire the semaphore and then regardless of whether or
not it was acquire we immediately release it. This will force us into
a known good state.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit adds a callback which allows to adjust the maximum transmit
bitrate the card can output. This makes it possible to get a smooth
traffic instead of the default burst-y behaviour when trying to output
e.g. a video stream.
Much of the logic needed to get a correct bcnrc_val was taken from the
ixgbe_set_vf_rate_limit() function.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Xeon D KR backplane is different from other backplanes,
in that we can't use auto-negotiation to determine the
mode. Instead, use whatever the user configured.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for generic Tx checksums to the ixgbevf driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers. In
the case of the VF drivers this meant adding support for SCTP CRCs, and
inner checksum offloads for MPLS and various tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for generic Tx checksums to the ixgbe driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit converts commit c762dff24c ("ixgbe: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d10549 ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The source for the ops structure contents are const, so make them
so. Copy them in place with structure assignments instead of memcpys.
Make the mbx_ops accessed by reference instead of making a copy of
the source structure. Update copyright date on the touched files.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were adding VLAN 0 twice each time we restored the VLAN configuration.
Instead of doing it twice we can just start working through the active
VLANs from ID 1 on and skip the double write.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While doing the work on igb I realized there were a few cases where we were
still adding VLANs to the VLVF entries for the PF when they were not
needed. This patch cleans that up so that the only time we add a PF entry
to the VLVF is either for VLAN 0 or if the PF has requested a VLAN that a VF
is already using.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When running certain routing protocols like VRRP, VF guests need the
ability to set the unicast address of the interface. Extend the new ndo
trust feature to let the hypervisor trust a guest to set/update its own
unicast address.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the reset flags to adapter->state in order to make use of bit
operations.
This is an alternative patch to the one previously submitted by
John Greene.
Suggested-by: Alexander Duyck <aduyck@mirantis.com>
Reported-by: Scott Otto <otts62@yahoo.com>
Reported-by: John Greene <jogreene@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It seem to be non intentionally changed to Tx in
commit adc810900a ("ixgbe: Refactor busy poll socket code to address
multiple issues")
Lock is taken from ixgbe_low_latency_recv, and there under this
lock we use ixgbe_clean_rx_irq so it looks wrong for me to increment
Tx counter.
Yield stats can be shown through ethtool:
ethtool -S enp129s0 | grep yield
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix support for 16 bit source/dest port matches in ixgbe model.
u32 uses a single 32-bit key value for both source and destination ports
starting at offset 0. So replace the 2 functions with a single function
that takes this key value/mask to program both source and dest ports.
Verified with the following filter:
#tc qdisc add dev p4p1 ingress
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1: u32 divisor 1
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:10 u32 ht 800: link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:10 u32 ht 1: \
match tcp src 1024 ffff match tcp dst 80 ffff action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:11 u32 ht 1: \
match tcp src 1025 ffff action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:12 u32 ht 1: \
match tcp dst 81 ffff action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the incorrect check for mask in ixgbe_configure_clsu32 and
drop the 'mask' field that is not required in struct ixgbe_mat_field
Verified with the following filters:
#tc qdisc add dev p4p1 ingress
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: \
match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: \
match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:3 u32 ht 800: \
match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:4 u32 ht 800: \
match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for handle ids when adding/deleting hash nodes OR adding/deleting
filter entries and limit them to max number of links or header nodes
supported(IXGBE_MAX_LINK_HANDLE).
Start from bit 0 when setting hash table bit-map.(adapter->tables)
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function is only used in ixgbe_main.c
Resolves a "missing prototype" warning when building the driver with W=1
Reported-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return error when a MAC address change is rejected by the PF.
This will prevent the user from modifying the MAC address when
that operation is not permitted.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use udelay instead of usleep_range because this can be called while
a lock is held.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ATR code was assuming that it would be able to use tcp_hdr for
every TCP frame that came through. However this isn't the case as it
is possible for a frame to arrive that is TCP but sent through something
like a raw socket. As a result the driver was setting up bad filters in
which tcp_hdr was really pointing to the network header so the data was
all invalid.
In order to correct this I have added a bit of parsing logic that will
determine the TCP header location based off of the network header and
either the offset in the case of the IPv4 header, or a walk through the
IPv6 extension headers until it encounters the header that indicates
IPPROTO_TCP. In addition I have added checks to verify that the lowest
protocol provided is recognized as IPv4 or IPv6 to help mitigate raw
sockets using ETH_P_ALL from having ATR applied to them.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VXLAN port number should be stored in network order instead of in host
order as it is accessed from the hot-path in ATR. This way we can avoid
having to do any byte swaps in order to validate the port number.
I moved the vxlan_port value into a hole in the read-mostly region of the
adapter struct. This way it should be in a warm cache-line instead of in
some isolated region in memory when it needs to be accessed.
In addition I went through and stripped a bunch of unneeded ifdef flags
since having an extra variable present doesn't really hurt anything and
makes the code easier to read. I also went through and dropped the
NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides
no value as the flag is not evaluated in the Rx path.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit c9f53e63c2 ("ixgbe: Refactor MAC address configuration code")
introduced code that doesn't set HW register RAR0 to default mac address
but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets
that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF.
This commit sets RAR0 correctly to default HW mac address.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects
the net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular interest
here is that we have left the driver in staging since it still has an
API that people object to. Intel is working on a fix, but getting
these patches in now helps keep me sane as the upstream and Intel's
trees were over 300 patches apart.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t2Ko
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"Round two of 4.6 merge window patches.
This is a monster pull request. I held off on the hfi1 driver updates
(the hfi1 driver is intimately tied to the qib driver and the new
rdmavt software library that was created to help both of them) in my
first pull request. The hfi1/qib/rdmavt update is probably 90% of
this pull request. The hfi1 driver is being left in staging so that
it can be fixed up in regards to the API that Al and yourself didn't
like. Intel has agreed to do the work, but in the meantime, this
clears out 300+ patches in the backlog queue and brings my tree and
their tree closer to sync.
This also includes about 10 patches to the core and a few to mlx5 to
create an infrastructure for configuring SRIOV ports on IB devices.
That series includes one patch to the net core that we sent to netdev@
and Dave Miller with each of the three revisions to the series. We
didn't get any response to the patch, so we took that as implicit
approval.
Finally, this series includes Intel's new iWARP driver for their x722
cards. It's not nearly the beast as the hfi1 driver. It also has a
linux-next merge issue, but that has been resolved and it now passes
just fine.
Summary:
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects the
net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular
interest here is that we have left the driver in staging since it
still has an API that people object to. Intel is working on a fix,
but getting these patches in now helps keep me sane as the upstream
and Intel's trees were over 300 patches apart"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (362 commits)
IB/ipoib: Allow mcast packets from other VFs
IB/mlx5: Implement callbacks for manipulating VFs
net/mlx5_core: Implement modify HCA vport command
net/mlx5_core: Add VF param when querying vport counter
IB/ipoib: Add ndo operations for configuring VFs
IB/core: Add interfaces to control VF attributes
IB/core: Support accessing SA in virtualized environment
IB/core: Add subnet prefix to port info
IB/mlx5: Fix decision on using MAD_IFC
net/core: Add support for configuring VF GUIDs
IB/{core, ulp} Support above 32 possible device capability flags
IB/core: Replace setting the zero values in ib_uverbs_ex_query_device
net/mlx5_core: Introduce offload arithmetic hardware capabilities
net/mlx5_core: Refactor device capability function
net/mlx5_core: Fix caching ATOMIC endian mode capability
ib_srpt: fix a WARN_ON() message
i40iw: Replace the obsolete crypto hash interface with shash
IB/hfi1: Add SDMA cache eviction algorithm
IB/hfi1: Switch to using the pin query function
IB/hfi1: Specify mm when releasing pages
...
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer updates from Thomas Gleixner:
"The timer department delivers this time:
- Support for cross clock domain timestamps in the core code plus a
first user. That allows more precise timestamping for PTP and
later for audio and other peripherals.
The ptp/e1000e patches have been acked by the relevant maintainers
and are carried in the timer tree to avoid merge ordering issues.
- Support for unregistering the current clocksource watchdog. That
lifts a limitation for switching clocksources which has been there
from day 1
- The usual pile of fixes and updates to the core and the drivers.
Nothing outstanding and exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
time/timekeeping: Work around false positive GCC warning
e1000e: Adds hardware supported cross timestamp on e1000e nic
ptp: Add PTP_SYS_OFFSET_PRECISE for driver crosstimestamping
x86/tsc: Always Running Timer (ART) correlated clocksource
hrtimer: Revert CLOCK_MONOTONIC_RAW support
time: Add history to cross timestamp interface supporting slower devices
time: Add driver cross timestamp interface for higher precision time synchronization
time: Remove duplicated code in ktime_get_raw_and_real()
time: Add timekeeping snapshot code capturing system time and counter
time: Add cycles to nanoseconds translation
jiffies: Use CLOCKSOURCE_MASK instead of constant
clocksource: Introduce clocksource_freq2mult()
clockevents/drivers/exynos_mct: Implement ->set_state_oneshot_stopped()
clockevents/drivers/arm_global_timer: Implement ->set_state_oneshot_stopped()
clockevents/drivers/arm_arch_timer: Implement ->set_state_oneshot_stopped()
clocksource/drivers/arm_global_timer: Register delay timer
clocksource/drivers/lpc32xx: Support timer-based ARM delay
clocksource/drivers/lpc32xx: Support periodic mode
clocksource/drivers/lpc32xx: Don't use the prescaler counter for clockevents
clocksource/drivers/rockchip: Add err handle for rk_timer_init
...
Modern Intel systems supports cross timestamping of the network device
clock and Always Running Timer (ART) in hardware. This allows the
device time and system time to be precisely correlated. The timestamp
pair is returned through e1000e_phc_get_syncdevicetime() used by
get_system_device_crosststamp(). The hardware cross-timestamp result
is made available to applications through the PTP_SYS_OFFSET_PRECISE
ioctl which calls e1000e_phc_getcrosststamp().
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: kevin.b.stanton@intel.com
Cc: kevin.j.clarke@intel.com
Cc: hpa@zytor.com
Cc: jeffrey.t.kirsher@intel.com
Cc: netdev@vger.kernel.org
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Christopher S. Hall <christopher.s.hall@intel.com>
[jstultz: Reworked to use new interface, commit message tweaks]
Signed-off-by: John Stultz <john.stultz@linaro.org>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original series drivers would get offload requests for cls_u32
rules even if the feature bit is disabled. This meant the driver had
to do a boiler plate check on the feature bit before adding/deleting
the rule.
This patch lifts the check into the core code and removes it from the
driver specific case.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a Client interface for i40iw driver
support. Also expands the Virtchannel to support messages
from i40evf driver on behalf of i40iwvf driver.
This client API is used by the i40iw and i40iwvf driver
to access the core driver resources brokered by the i40e driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Problem: When switching off VLAN offloading on an i350, the VLAN
interface gets unusable. For testing, set up a VLAN on an i350
and some remote machine, e.g.:
$ ip link add link eth0 name eth0.42 type vlan id 42
$ ip addr add 192.168.42.1/24 dev eth0.42
$ ip link set dev eth0.42 up
Offloading is switched on by default:
$ ethtool -k eth0 | grep vlan-offload
rx-vlan-offload: on
tx-vlan-offload: on
$ ping -c 3 -I eth0.42 192.168.42.2
[...works as usual...]
Now switch off VLAN offloading and try again:
$ ethtool -K eth0 rxvlan off
Actual changes:
rx-vlan-offload: off
tx-vlan-offload: off [requested on]
$ ping -c 3 -I eth0.42 192.168.42.2
PING 192.168.42.2 (192.168.42.2) from 192.168.42.1 eth0.42: 56(84) bytes of da
ta.
--- 192.168.42.2 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 1999ms
I can only reproduce it on an i350, the above works fine on a 82580.
While inspecting the igb source, I came across the code in igb_set_vmolr
which sets the E1000_VMOLR_STRVLAN/E1000_DVMOLR_STRVLAN flags once and
for all, and in all of the igb code there's no other place where the
STRVLAN is set or cleared. Thus, VLAN stripping is enabled in igb
unconditionally, independently of the offloading setting.
I compared that to the latest Intel igb-5.3.3.5 driver from
http://sourceforge.net/projects/e1000/ which in fact sets and clears the
STRVLAN flag independently from igb_set_vmolr in its own function
igb_set_vf_vlan_strip, depending on the vlan settings.
So I included the STRVLAN handling from the igb-5.3.3.5 driver into our
current igb driver and tested the above scenario again. This time ping
still works after switching off VLAN offloading.
Tested on i350, with and without addtional VFs, as well as on 82580
successfully.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A similar issue was addressed a few years ago in the following thread:
http://www.spinics.net/lists/netdev/msg245877.html
At that time there were concerns that removing this statement may cause other
side effects. However the submitter addressed those concerns. But the dialogue
went cold. We have a new case where a customers application is registering and
un-registering multicast addresses every few seconds. This is leading to many
"Link is Up" messages in the logs as a result of the
"netif_carrier_off(netdev)" statement called by igbvf_msix_other(). Also on
some kernels it is interfering with the bonding driver causing it to failover
and subsequently affecting connectivity.
The Sourgeforge driver does not make this call and is therefore not affected.
If there were any side effects I would expect that driver to also be affected.
I have tested re-loading the igbvf driver and downing the adapter with the PF
entity on the host where the VM has this patch. When I bring it back up again
connectivity is restored as expected. Therefore I request that this patch gets
submitted.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for generic Tx checksums to the igbvf driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers. In
the case of the VF drivers this meant adding support for SCTP CRCs, and
inner checksum offloads for MPLS and various tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for generic Tx checksums to the igb driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
E1000_MRQC_ENABLE_RSS_4Q enables 4 and 8 queues depending on the part
so rename to be generic.
Similarly, E1000_MRQC_ENABLE_VMDQ_RSS_2Q has no numeric meaning so
rename to be more generic.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In general case the maximum supported half cycle time of the synchronized
output clock is 70msec. Slower half cycle time than 70msec can be
programmed also as long as the output clock is synchronized to whole
seconds, useful specifically for generating a 1Hz clock.
Permitted values for the clock half cycle time are: 125,000,000 decimal,
250,000,000 decimal and 500,000,000 decimal (equals to 125msec, 250msec
and 500msec respectively).
Before this patch, only the half cycle time of less than or equal to 70msec
uses the I210 clock output function. This patch adds additional conditions
when half cycle time is equal to 125msec or 250msec or 500msec to use
clock output function.
Under other conditions, interrupt driven target time output events method
is still used to generate the desired clock output.
Signed-off-by: Roland Hii <roland.king.guan.hii@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Override EEPROM settings for specific OEM devices.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This e1000_phy_operations structure is never modified, so declare it as
const. Other structures of this type are already const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I210 device IPv6 autoconf test sometimes fails,
because DAD NS for link-local is not transmitted.
This packet is silently dropped.
This problem is seen only GbE environment.
igb_watchdog_task link up detection continues to the following process.
The following cases are observed:
1.PHY 1000BASE-T Status Register Remote receiver status bit is NG.
(NG status becomes OK after about 200 - 700ms)
2.In this case, the transfer packet is silently dropped.
1000BASE-T Status register
[Expected]: 0x3800 or 0x7800
[problem occurred]: 0x2800 or 0x6800
Frequency of occurrence: approx 1/10 - 1/40 observed
In order to avoid this problem,
wait until 1000BASE-T Status register "Remote receiver status OK"
After applying this patch, at least 400 runs succeed with no problems.
Signed-off-by: Takuma Ueba <t.ueba11@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i219 (4) and i219 (5) are the next LOM generations that will be
available on the next Intel platform (KabeLake).
This patch provides the initial support for the devices.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There have been bugs caused by HW ULP configuration settings not being
properly cleared after cable connect in V-Pro capable systems.
This caused HW to get out of sync occasionally.
The fix ensures that ULP settings are cleared in HW after
LAN cable re-connect.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on feedback from HW team, the configured value of the internal PHY
HW FIFO pointer gap was incorrect for non-gig speeds.
This patch provides the correct configuration.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several packet loss issues were reported for which the root cause for
them was an incorrect configuration of internal HW PHY clock gating
mechanism by SW.
This patch provides the correct mechanism.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to system level changes introduced in Skylake, ULP exit takes
significantly longer to occur. Therefore, driver must wait longer for.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements set_per_queue_coalesce for i40e driver.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements get_per_queue_coalesce for i40e driver.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we reset a VF, its VSI goes away, and it gets a new one. So don't
hang on to the now-stale local VSI pointer. It just leads to suffering
and kernel panics.
Change-ID: Ia8823b4e85893e95e963acee284968022b29177a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to suspend scheduling or any pending service task during driver
unload process, so that new task will not be scheduled. This patch sets
the suspend flag bit during reload which avoids service task execution.
Change-ID: I017c57b5d6656564556e3c5387da671369a572ac
Signed-off-by: Pandi Kumar Maharajan <pandi.maharajan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.
We can't use AdminQ calls in i40e_clear_hw() because the HW is being
initialized and the AdminQ is not alive. We recently added an AQ
related replacement for reading PFLAN_QALLOC, and this patch puts
back the original register read.
Change-ID: Ib027168c954a5733299aa3a4ce5f8218c6bb5636
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.
Change-ID: Ibb00983e8dcba71f4b760222a609a5fcaa726f18
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new opcodes and struct used for asking the firmware to update Rx
control registers that need extra care when being accessed while under
heavy traffic - e.g. sustained 64byte packets at line rate on all ports.
The firmware will take extra steps to be sure the register accesses
are successful.
The registers involved are:
PFQF_CTL_0
PFQF_HENA
PFQF_FDALLOC
PFQF_HREGION
PFLAN_QALLOC
VPQF_CTL
VFQF_HENA
VFQF_HREGION
VSIQF_CTL
VSILAN_QBASE
VSILAN_QTABLE
VSIQF_TCREGION
PFQF_HKEY
VFQF_HKEY
PRTQF_CTL_0
GLFCOE_RCTL
GLFCOE_RSOF
GLQF_CTL
GLQF_SWAP
GLQF_HASH_MSK
GLQF_HASH_INSET
GLQF_HSYM
GLQF_FC_MSK
GLQF_FC_INSET
GLQF_FD_MSK
PRTQF_FD_INSET
PRTQF_FD_FLXINSET
PRTQF_FD_MSK
Change-ID: I56c8144000da66ad99f68948d8a184b2ec2aeb3e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return from i40e_vsi_reinit_setup() if vsi param is NULL.
This makes this code consistent with all the other code that
checks for NULL before using one of the VSI pointers accessed
with an indexed variable. (Indexed VSI pointers are
intentionally set to NULL in i40e_vsi_clear() and
i40e_remove().
Change-ID: I3bc8b909c70fd2439334eeae994d151f61480985
Signed-off-by: John Underwood <johnx.underwood@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds 7 new register definitions for programming the
parser, flow director and RSS blocks in the HW.
Change-ID: I31e76673125275f3c69a14c646361919d04dc987
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes an issue where a previously removed message
has returned. Changing the message type to dev_dbg
leaves the info, if desired, but takes it out of normal
everyday usage. Also changed call to only provide port
data when its valid and not when its not (delete case).
Change-ID: Ief6f33b915f6364c24fa8e5789c2fc3168b5e2ed
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just like Tx queues don't wait for Rx queues to be disabled before
DCB has been reconfigured.
Check the queues are disabled only after the DCB configuration has
been applied to the VSI(s) managed by the PF driver.
In case of any timeout issue a PF reset to recover.
Change-ID: Ic51e94c25baf9a5480cee983f35d15575a88642c
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When linking with particular PHY types (ex: copper PHY), the amount of
time it takes for the GLGEN_RSTAT_DEVSTATE to be set increases greatly,
which can lead to a timeout and failure to load the driver.
Change-ID: If02be0dfcd7c57fdde2d5c81cd63651260cd2029
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the ethtool identify adapter
functionality did not work for some copper PHY's. Without this
patch, the blink led functionality fails on some parts. This
patch adds PHY write code to blink led's on parts where this
functionality is contained in the PHY rather than the MAC.
Change-ID: Iee7b3453f61d5ffd0b3d03f720ee4f17f919fcc2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds functions to blink led on devices using
10GBaseT PHY since MAC registers used in other designs
do not work in this device configuration.
Change-ID: Id4b88c93c649fd2b88073a00b42867a77c761ca3
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On all of the other Intel drivers we place checksum close to TSO as they
have a significant amount in common and it can help to reduce the decision
tree for how to handle the frame as the first check in TSO is to see if
checksumming is offloaded, and if it is not we can skip _BOTH_ TSO and Tx
checksum offload based on a single check.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to rewrite the logic for how we determine if we can
transmit the frame or if it needs to be linearized.
The previous code for this function was using a mix of division and modulus
division as a part of computing if we need to take the slow path. Instead
I have replaced this by simply working with a sliding window which will
tell us if the frame would be capable of causing a single packet to span
several descriptors.
The logic for the scan is fairly simple. If any given group of 6 fragments
is less than gso_size - 1 then it is possible for us to have one byte
coming out of the first fragment, 6 fragments, and one or more bytes coming
out of the last fragment. This gives us a total of 8 fragments
which exceeds what we can allow so we send such frames to be linearized.
Arguably the use of modulus might be more exact as the approach I propose
may generate some false positives. However the likelihood of us taking much
of a hit for those false positives is fairly low, and I would rather not
add more overhead in the case where we are receiving a frame composed of 4K
pages.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In an upcoming patch I would like to have access to the descriptor count
used for the data portion of the frame. For this reason I am splitting up
the descriptor count function from the function that stops the ring.
Also in order to try and reduce unnecessary duplication of code I am moving
the slow-path portions of the code out of being inline calls so that we can
just jump to them and process them instead of having to build them into
each function that calls them.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the code for determining the L4 protocol and L3 header
length so that when IPv6 extension headers are being used we can determine
the offset and type of the L4 protocol.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes should have enabled support for IPv6 based tunnels and
support for TSO with outer UDP checksums. As such we can update the
feature flags to reflect that.
In addition we can clean-up the flags that aren't needed such as SCTP and
RXCSUM since having the bits there doesn't add any value.
I also found one spot where we were setting the same flag twice. It looks
like it was probably a git merge error that resulted in the line being
duplicated. As such I have dropped it in this patch.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes should have enabled support for IPv6 based tunnels and
support for TSO with outer UDP checksums. As such we can update the
feature flags to reflect that.
In addition we can clean-up the flags that aren't needed such as SCTP and
RXCSUM since having the bits there doesn't add any value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All of the documentation in the datasheets for the XL710 do not call out
any reason to exclude support for IPv6 based tunnels. As such I am
dropping the code that was excluding these tunnel types from having their
port numbers recognized. This way we can take advantage of things such as
checksum offload for inner headers over IPv6 based VXLAN or GENEVE
tunnels.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains a number of fixes to make certain that we are using
the correct protocols when parsing both the inner and outer headers of a
frame that is mixed between IPv4 and IPv6 for inner and outer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL722 has support for providing the outer UDP tunnel checksum on
transmits. Make use of this feature to support segmenting UDP tunnels with
outer checksums enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is mostly a minor clean-up for the Rx checksum path in order to avoid
some of the unnecessary conditional checks that were being applied.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add exception handling to the Tx checksum path so that we can handle cases
of TSO where the frame is bad, or Tx checksum where we didn't recognize a
protocol
Drop I40E_TX_FLAGS_CSUM as it is unused, move the CHECKSUM_PARTIAL check
into the function itself so that we can decrease indent.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch defers writing to the Tx descriptor bits until we know we have
successfully completed a given operation. So for example we defer updating
the tunnelling portion of the context descriptor until we have fully
identified the type.
The advantage to this approach is that we can assemble values as we go
instead of having to try and kludge everything together all at once. As a
result we can significantly clean up the tunneling configuration for
instance as we can just do a pointer walk and do the math for the distance
between each set of points.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for IPv6 extension headers in setting up the Tx
checksum. Without this patch extension headers would cause IPv6 traffic to
fail as the transport protocol could not be identified.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes two issues. First was the fact that iphdr(skb)->protocl
was being used to test for the outer transport protocol. This completely
breaks IPv6 support. Second was the fact that we cleared the flag for v4
going to v6, but we didn't take care of txflags going the other way. As
such we would have the v6 flag still set even if the inner header was v4.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx checksum path was maintaining a set of 3 pointers and two lengths in
order to prepare the packet for being checksummed. The thing is we only
really needed 2 pointers, and the lengths that were being maintained can
easily be computed.
As such we can replace the IPv4 and IPv6 header pointers with one single
union that represents both, or a generic pointer to the start of the
network header. For the L4 headers we can do the same with TCP and a
generic pointer to the start of the transport header. The length of the
TCP header is obtained by simply multiplying doff by 4, and the network
header length can be obtained by subtracting the network header pointer
from the transport header pointer.
While I was at it I renamed l4_hdr to l4_proto to make it a bit more clear
and less likely to be confused with l4.hdr which is the transport header
pointer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch goes through and pulls all of the spots where we were updating
either the TCP or IP checksums in the TSO and checksum path into the TSO
function. The general idea here is that we should only be updating the
header after we verify we have completed a skb_cow_head check to verify the
head is writable.
One other advantage to doing this is that it makes things much more
obvious. For example, in the case of IPv6 there was one spot where the
offset of the IPv4 header checksum was being updated which is obviously
incorrect.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that the L4 header offsets and such can be ignored
when dealing with the L3 checksum and length update. This is done making
use of two things.
First we can just use the offset from the L4 header to the start of the
packet to determine the L4 offset, and from that we can then make use of
the data offset to determine the full length of the headers.
As far as adjusting the checksum to remove the length we can simply add the
inverse of the length instead of having to recompute the entire
pseudo-header without the length. In the case of an IPv6 header this
should be significantly cheaper since we can make use of a value we already
needed instead of having to read the source and destination address out of
the packet.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of casing u32 values to u64 it makes more sense to just start out
with u64 values in the first place. This way we don't need to create a
mess with all of the casts needed to populate a 64b value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e and i40evf drivers contained code for inserting an outer checksum
on UDP tunnels. The issue however is that the upper levels of the stack
never requested such an offload and it results in possible errors.
In addition the same logic was being applied to the Rx side where it was
attempting to validate the outer checksum, but the logic there was
incorrect in that it was testing for the resultant sum to be equal to the
header checksum instead of being equal to 0.
Since this code is so massively flawed, and doing things that we didn't ask
for it to do I am just dropping it, and will bring it back later to use as
an offload for SKB_GSO_UDP_TUNNEL_CSUM which can make use of such a
feature.
As far as the Rx feature I am dropping it completely since it would need to
be massively expanded and applied to IPv4 and IPv6 checksums for all parts,
not just the one that supports Tx checksum offload for the outer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In MFP mode particularly when we were setting the PF VSI in limited
promiscuous, the HW switch was still mirroring the outgoing packets
from other VSIs (VF/VMdq) onto the PF VSI.
With this new bit set, the mirroring doesn't happen any more and so
we are in limited promiscuous on the PF VSI in MFP which is similar
to defport.
An API check is not required, since this bit is reserved for FW API
version < 1.5
Also update copyright year in file headers.
Change-ID: I9840cb95f11dde733d943cb03ce84f68b9611bc8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In one obscure corner case, it was possible to clear the NVM update wait
flag when no update_done message was actually received. This patch
cleans the event descriptor before use, and moves the opcode check to
where it won't get done if there was no event to clean.
Also update copyright year in file headers.
Change-ID: I68bbc41965e93f4adf07cbe98b9dfd63d41509a4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset fails to complete, the driver gets its affairs in order and
awaits the cold solace of rmmod. Unfortunately, it was not properly
setting the adapter state, which would cause a panic on rmmod, instead
of the desired surcease.
Set the adapter state to DOWN in this case, and avoid a panic.
Change-ID: I6fdd9906da52e023f8dc744f7da44b5d95278ca9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure we return EBUSY while finishing up a reset, and add a few bits
for better debug messages.
Change-ID: I23f6c28a8d96d7aa171abcc265737cec7826c292
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Explain why we cannot remove this code, even though it works differently
than any of our other interrupt cause handling code.
Change-ID: Ie66203bd037a466066036611c31d44f759ec5176
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The queues should never be enabled/disabled in the interrupt handler,
ICR0 interrupt enable should be the only thing that needs to be
dynamically changed in the handler.
This patch fixes that. Without this patch X722 platforms were
seeing weird ping timings when in Legacy mode since it takes
a whole lot of time for the HW/FW to re-enable queues.
Change-ID: If065afc45d81c5a19d4a94a00cd5b8f61cefc40c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case where we have a page fully used by receive data, we need to
release the page fully to the stack. Instead of calling get_page (which
increments the page count) followed by free_page (which decrements the
page count), just donate our reference to the stack. Although this
donation is not tax deductible, it does allow us to avoid two very
expensive atomic operations that reverse each other.
Change-ID: If70739792d5748995fc175ec92ac2171ed4ad8fc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed mapping of SEID is removed from specification. Hence
this patch removes code which was using hard coded base VEB SEID.
Changed FCoE code to use "hw->pf_id" to obtain correct "idx"
and verified.
Removed defines for BASE VSI/VEB SEID and BASE_PF_SEID since it
is not used anymore.
Change-ID: Id507cf4b1fae1c0145e3f08ae9ea5846ea5840de
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch falls back to enabling unicast, multicast and
broadcast promiscuous mode when the driver must disable it's use
of "default port" aka defport mode (which is normally used to
provide a promiscuous mode), due to internal incompatibility
with Multiple Function per Port (aka MFP).
The situation that requires this patch is when Physical
Function 0 is the device being used, and it can support SR-IOV
when MFP is enabled, via the driver creating a VEB on an MFP
enabled adapter.
Change-ID: Ie90b00d0d58782a5dfcf2c3c9725a2eb90bd63d8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.
Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.
Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes use of a pointer called hw consistent
in the i40e_remove function.
Change-ID: Idacc7ff0a09a68289c57457a78618bf5497de077
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Support packet split receive on VFs. This is off by default but can be
enabled using ethtool private flags. Because we need to trigger a reset
from outside of i40evf_main.c, create a new function to do so, and
export it.
Also update copyright year in file headers.
Change-ID: I721aa5d70113d3d6d94102e5f31526f6fc57cbbb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a completely unused file "dump" in debugfs that
never panned out to be useful.
Change-ID: I12bb9e37b5a83299725dda815a8746157baf6562
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have a define for this, use it. No functional change.
Change-ID: Ic0e3ea4f562e46de63b2a8de07f291ccc10205fd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-02-17
This series contains updates to i40e/i40evf only (again).
Jesse moves sync_vsi_filters() up in the service_task because it may need
to request a reset, and we do not want to wait another round of service
task time. Refactored the enable_icr0() in order to allow it to be
decided by the caller whether the CLEARPBA (clear pending events) bit will
be set while re-enabling the interrupt. Also provides the "Don't Give Up"
patch, where the driver will keep polling trying to allocate receive buffers
until it succeeds. This should keep all receive queues running even in
the face of memory pressure. Cleans up the debugging helpers by putting
everything in hex to be consistent.
Neerav updates the DCB firmware version related checkes specific to X710
and XL710 only since the checks are not required for X722 devices.
Shannon adds the use of the new shared MAC filter bit for multicast and
broadcast filters in order to make better use of the filters available
from the device. Added a parameter to allow the driver to set the
enable/disable of statistics gathering in the hardware switch. Also the
L2 cloud filtering parameter is removed since it was never used.
Anjali refactors the force_wb and WB_ON_ITR functionality since
Force-WriteBack functionality in X710/XL710 devices has been moved out of
the clean routine and into the service task, so we need to make sure
WriteBack-On-ITR is separated out since it is still called from clean.
Catherine changes the VF driver string to reflect all the products that
are supported.
Mitch refactors the packet split receive code to properly use half-pages
for receives. Also changes the use of bitwise operators to logical
operators on clean_complete variable, while making a witty reference to
Mr. Spock. Cleans up (i.e. removes) the hsplit field in the ring
structure and use the existing macro to detect packet split enablement,
which allows debugfs dumps of the VSI to properly show which recevie
routine is in use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 9d35cf062e ("net: ixgbe: add minimal parser details for ixgbe")
Reported-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I incorrectly used __u32 types where we should be using u32 types when
I added the ixgbe_model.h file.
Fixes: 9d35cf062e ("net: ixgbe: add minimal parser details for ixgbe")
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump version to i40e-1.4.13 and i40evf-1.4.9
Change-ID: I9db37f9d4899141c3e5455dfb456d45465b8c035
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Get rid of the unused hsplit field in the ring struct and use the
existing macro to detect packet split enablement. This allows debugfs
dumps of the VSI to properly show which Rx routine is in use.
Change-ID: Ic4e9589e6a788ab196ed0850703f704e30c03781
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mr. Spock would certainly raise an eyebrow to see us using bitwise
operators, when we should clearly be relying on logic. Fascinating.
Change-ID: Ie338010c016f93e9faa2002c07c90b15134b7477
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the packet split Rx code to properly use half-pages for
receives. The previous code was doing way more mapping and unmapping
than it needed to, and wasn't properly using half-pages.
Increment the page use count each time we give a half-page to an skb,
knowing that the stack will probably process and release the page before
we need it again. Only free and reallocate pages if the count shows that
both half-pages are in use. Add counters to track reallocations and page
reuse.
Change-ID: I534b299196036b64be82b4861a0a4036310a8f22
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e and i40evf drivers now cleanly handle allocation
failures and can avoid kernel log spew from the memory allocator
when allocations fail, so set __GFP_NOWARN on Rx buffer alloc.
Change-ID: Ic9e1b83c495e2a3ef6b069ba7fb6e52ce134cd23
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The debugging helpers for showing descriptor rings were
dumping the indexes in decimal and the offsets in hex.
Put everything in hex and at least be consistent.
Also update copyright year in file header.
Change-ID: Ia35a21411a2ddb713772dffb4e8718889fcfc895
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the "Don't Give Up" patch. Previously the
driver could fail an allocation, and then possibly stall
a queue forever, by never coming back to continue receiving
or allocating buffers.
With this patch, the driver will keep polling trying to allocate
receive buffers until it succeeds. This should keep all receive
queues running even in the face of memory pressure.
Also update copyright year in file header.
Change-ID: I2b103d1ce95b9831288a7222c3343ffa1988b81b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While re-enabling interrupts the driver would clear all pending
causes. This meant that if an interrupt was generated while the driver
was cleaning or polling with interrupts disabled, then that interrupt
was lost. This could cause a queue to become dead, especially for
receive. Refactored the enable_icr0 function in order to allow
it to be decided by the caller whether the CLEARPBA (clear pending
events) bit will be set while re-enabling the interrupt.
Also update copyright year in file headers.
Change-ID: Ic1db100a05e13c98919057696db147a258ca365a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the driver string to 40-10 Gigabit instead of XL710/X710 for X722
and all future products.
Also update copyright year in file header.
Change-ID: I57fae656b36dc4eb682b2b7a054f8f48f3589149
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that the Force-WriteBack functionality in X710/XL710 devices
has been moved out of the clean routine and into the service task,
we need to make sure WriteBack-On-ITR is separated out since it
is still called from clean.
In the X722 devices, Force-WriteBack implies WriteBack-On-ITR but
without the interrupt, which put the driver into a missed
interrupt scenario and a potential tx-timeout report.
With this patch, we break the two functions out, and call the
appropriate ones at the right place. This will avoid creating missed
interrupt like scenarios for X722 devices.
Also update copyright year in file headers.
Change-ID: Iacbde39f95f332f82be8736864675052c3583a40
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new parameters for add_veb allow us to enable and disable VEB stats,
so let's use them.
Update copyright year.
Change-ID: Ie6e68c68e2d1d459e42168eda661051b56bf0a65
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the latest firmware, statistics gathering can now be enabled and
disabled in the HW switch, so we need to add a parameter to allow the
driver to set it as desired. At the same time, the L2 cloud filtering
parameter has been removed as it was never used.
Older drivers working with the newer firmware and newer drivers working
with older firmware will not run into problems with these bits as the
defaults are reasonable and there is no overlap in the bit definitions.
Also, newer drivers will be forced to update because of the change in
function call parameters, a reminder that the functionality exists.
Also update copyright year.
Change-ID: I9acb9160b892ca3146f2f11a88fdcd86be3cadcc
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the use of the new Shared MAC filter bit for multicast and broadcast
filters in order to make better use of the filters available from the
device. The FW folks have assured me that setting this bit on older FW
will have no affect, so we don't need a version check.
Also fixed a stray indent problem nearby.
Also update copyright year.
Change-ID: I4c5826a32594382a7937a592a24d228588cee7aa
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the DCB firmware version related checks specific to
X710 and XL710 only. These checks are not required for
X722 family of devices.
Introduced an inline routine to help determine if the
MAC type is X710/XL710 or not.
Moved the firmware version related checks in i40e_sw_init()
and defined flags for different cases
Fix the version check to allow using "Set LLDP MIB" AQ
for beyond FVL4 FW releases.
Change-ID: Ib78288343de983aa0354fc28aa36e99b073662c0
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The sync_vsi_filters function is moved up in the service_task because
it may need to request a reset, and we don't want to wait another round
of service task time.
NOTE: Filters will be replayed by sync_vsi_filters including broadcast
and promiscuous settings.
Also, added some error handling in this space in case any of these
fail the driver will retry correctly.
Also update copyright year.
Change-ID: I23f3d552100baecea69466339f738f27614efd47
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit converts commit b499ffb0a2 ("i40e: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d10549 ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X722 can support automatic rule eviction for automatically added
flow director rules. Feature is (should be) disabled by default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure we check the GENEVE offload capable flag before
we attempt offload.
It also enables the Capability for XL710/X710 devices with FW API
version higher than 1.4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Assign the i40e_pf structure directly instead of using a large memcpy,
which avoids a sparse warning and lets the compiler optimize the copy
since it knows the size of the structure in advance.
Change-ID: I17604e23be2616521eb760290befcb767b52b3f7
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver already counted allocation errors, so print
them as part of the ethtool -S output. Useful for debugging
if your system is having trouble making memory available for
the driver.
Change-ID: I83839fa86e81e6d80f03b917c88dd3ef9a64dde0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY interrupt mask bits mask out the events we don't want,
so we need to negate the bitmask of events we want.
Change-ID: I273244da5a8d285b6abc84fd68a90f1e6fa0393e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements necessary functions related to port
mirroring features such as add/delete mirror rule, function
to set promiscuous VLAN mode for VSI if mirror rule_type is
"VLAN Mirroring".
Change-ID: Iaf513fd5f188f99dcb977b48f99e73185dfddc40
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Nelson, Shannon <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The sync_vsi_filter function was allocating memory in such
a way that it could sleep (GFP_KERNEL) which was causing a problem
when called by the team driver under rcu_read_lock(), which cannot
be held while sleeping. Found with lockdep.
Change-ID: I4e59053cb5eedcf3d0ca151715be3dc42a94bdd5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't bother trying to set up a TSO if the skb->ip_summed is not
set to CHECKSUM_PARTIAL.
Change-ID: I6495b3568e404907a2965b48cf3e2effa7c9ab55
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver was using an offset based off a DMA handle while mapping and
unmapping using sync_single_range_for[cpu|device], where it should
be using DMA handle (returned from alloc_coherent) and the offset of the
memory to be sync'd.
Change-ID: I208256565b1595ff0e9171ab852de06b997917c6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Nelson, Shannon <shannon.nelson@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Missing space in comment, fixed.
Change-ID: I8cdf3ce5994b4a97dcc3eeb33422533918546667
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The probe routine already had a u32 val declared, no need
to do it again. Found by W=2 compile.
Change-ID: Id7b65f6d0ef6bb71067d0557f5be0202b6d8741e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-02-16
This series contains updates to i40e/i40evf only.
Shannon adds flags to MAC allocation requests to signify that the MAC VLAN
filters should come from the shared resource pool. Added a new "set switch
config" admin queue command and the new Cisco VXLAN-GPE cloud tunnel type
for the admin queue commands. Added more detail to the NVM update debug
message in order to see the full ethtool request data. Also added a few
more bits of netdev data into the debugfs output for dump VSI.
Pandi fixes the width of two datatypes which were being declared a different
size from what they are assigned.
Anjali fixes an issue where we were not doing write-back on interrupt
throttle for legacy case in x722.
Mitch adds a counter for ARQ overflows since sometimes an ever-growing
number indicates that something bad is happening. Also added 20G speed for
Tx bandwidth calculations.
Jesse refactors the DCB function based on a community suggestion to change
the multi-level if statement into a switch statement. Cleans up VF device
IDs in the PF, since it does not need to know them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures ixgbe will not try to offload hash tables from the
u32 module. The device class does not currently support this so until
it is enabled just abort on these tables.
Interestingly the more flexible your hardware is the less code you
need to implement to guard against these cases.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds initial support for offloading the u32 tc classifier. This
initial implementation only implements a few base matches and actions
to illustrate the use of the infrastructure patches.
However it is an interesting subset because it handles the u32 next
hdr logic to correctly map tcp packets from ip headers using the ihl
and protocol fields. After this is accepted we can extend the match
and action fields easily by updating the model header file.
Also only the drop action is supported initially.
Here is a short test script,
#tc qdisc add dev eth4 ingress
#tc filter add dev eth4 parent ffff: protocol ip \
u32 ht 800: order 1 \
match ip dst 15.0.0.1/32 match ip src 15.0.0.2/32 action drop
<-- hardware has dst/src ip match rule installed -->
#tc filter del dev eth4 parent ffff: prio 49152
#tc filter add dev eth4 parent ffff: protocol ip prio 99 \
handle 1: u32 divisor 1
#tc filter add dev eth4 protocol ip parent ffff: prio 99 \
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
#tc filter add dev eth4 parent ffff: protocol ip \
u32 ht 1: order 3 match tcp src 23 ffff action drop
<-- hardware has tcp src port rule installed -->
#tc qdisc del dev eth4 parent ffff:
<-- hardware cleaned up -->
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an ixgbe data structure that is used to determine what
headers:fields can be matched and in what order they are supported.
For hardware devices this can be a bit tricky because typically
only pre-programmed (firmware, ucode, rtl) parse graphs will be
supported and we don't yet have an interface to change these from
the OS. So its sort of a you get whatever your friendly vendor
provides affair at the moment.
In the future we can add the get routines and set routines to
update this data structure. One interesting thing to note here
is the data structure here identifies ethernet, ip, and tcp
fields without having to hardcode them as enumerations or use
other identifiers.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probe routine already has too many locals, just convert one
used for kzalloc into a kcalloc, eliminating the local.
Change-ID: I349049872b71f858cbeb91ad7836e6767fc7b7d1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF doesn't need to know about the VF's device IDs, so remove them.
Change-ID: I62cf0e0fffa1ace586e58e00bc271b10ae440f05
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a few more bits of netdev data into the debugfs output for dump VSI.
For now, we'll add the features, hw_features, vlan_features, and flags
bitflags and the state. More could be added later if needed.
Also, tweak a couple nearby output lines for output readability.
Change-ID: I9fb5a9da75c9ad7679498ce9ac3ba24d065ddd2e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Brandeburg, Jesse <jesse.brandeburg@intel.com>
Reviewed-by: Wyborny, Carolyn <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF is reset via VFLR, the device will be knocked out of bus
master mode, and the driver will fail to recover from the reset. Fix
this by enabling bus mastering after every reset. In a non-VFLR case,
the bus master bit will not be disabled, and this call will have no effect.
Change-ID: Id515859ac7a691db478222228add6d149e96801a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a little more detail to an NVM update debug message in order to
see the full ethtool request data.
Change-ID: Iab10437cb32d6fddc67ee347e7c0b42511e152cd
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a simple refactor suggested by the community
to change a multi-level if statement into a switch.
Change-ID: I831cf3c40426022220aa9b43990022d22dfd50db
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When calculating TX bandwidth for VFs, we need to know the link speed to
make sure we don't allocate more bandwidth than is available. Add 20G
link speed to the switch statement so we can support devices that link
at that speed.
Change-ID: I5409f6139d549e5832777db9c22ca0664e0c5f8b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes, ARQ overflows are a big deal and tell us that the
firmware/hardware/driver/something is having problems. But normally
they're no big deal. To assist in assessing this, add a counter to
our Ethtool stats. A handful of ARQ overflows during VF init is no
problem. A large, ever-growing number indicates that Something Bad is
happening.
Change-ID: Ie5348bfbc8a54a890559cb00279c28d976a55096
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were not doing write-back on interrupt throttle for Legacy case in X722.
This patch fixes that, so we do WB_ON_ITR for Legacy as well. Plus the issue
that we should still be setting NO_ITR if we are touching the DYN_CTLN register
since we do not want to change ITR setting here.
Change-ID: I5db8491ee1544118a389db839cecc93e1bbc480e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
lan_vsi_idx and lan_vsi_id are assigned to u16 data sized variables but
declared in u8. This patch fixes the width of the datatype.
Change-ID: If4bcbcc7d32f2b287c51cb33d17879691258dce2
Signed-off-by: Pandi Kumar Maharajan <pandi.maharajan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump AQ minor version to 1.5 for new FW features.
Change-ID: I5a790f7f519a2a8921aaa1c5663727dd1897ffec
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new AQ command and struct for managing a thermal sensor.
Change-ID: I6f5631839a0f3dca352a6c222f1269a960e2310a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new Cisco VXLAN-GPE cloud tunnel type for the Add Cloud Filter
and UDP tunnel AQ commands.
Change-ID: I2c093c7d79726c7fca08a36e5c63581a905da3d2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new Set Switch Config AdminQ command, and mark the L2 Filter
bit as deprecated in the Add VEB command.
Change-ID: I5b24790f14c56f0ddf3f70df1e486844146b039f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add flags to MAC allocation requests to signify that the MAC VLAN filters
should come from the shared resource pool rather than the dedicated PF
resource pools.
Change-ID: I4c2da64c01856edcb0982bc4aab75c5a91047a7a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2016-02-15
This series contains updates to igb only.
Shota Suzuki cleans up unnecessary flag setting for 82576 in
igb_set_flag_queue_pairs() since the default block already sets
IGB_FLAG_QUEUE_PAIRS to the correct value anyways, so the e1000_82576
code block is not necessary and we can simply fall through. Then fixes
an issue where IGB_FLAG_QUEUE_PAIRS can now be set by using "ethtool -L"
option but is never cleared unless the driver is reloaded, so clear the
queue pairing if the pairing becomes unnecessary as a result of "ethtool
-L".
Mitch fixes the igbvf from giving up if it fails to get the hardware
mailbox lock. This can happen when the PF-VF communication channel is
heavily loaded and causes complete communications failure between the
PF and VF drivers, so add a counter and a delay so that the driver will
now retry ten times before giving up on getting the mailbox lock.
The remaining patches in the series are from Alex Duyck, starting with the
cleaning up code that sets the MAC address. Then refactors the VFTA and
VLVF configuration, to simplify and update to similar setups in the ixgbe
driver. Fixed an issue were VLANs headers size was being added to the
value programmed into the RLPML registers, yet these registers already
take into account the size of the VLAN headers when determining the
maximum packet length, so we can drop the code that adds the size to
the RLPML registers. Cleaned up the configuration of the VF port based
VLAN configuration. Also fixed the igb driver so that we can fully
support SR-IOV or the recently added NTUPLE filtering while allowing
support for VLAN promiscuous mode. Also added the ability to use the
bridge utility to add a FDB entry for the PF to an igb port.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Also print an error message incase we do have to reconfigure as this
should no longer happen anymore due to ethtool changes. If it somehow
does occur, user should be made aware of it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a workaround partially implemented for the 82576 that is needed
in order for VLAN tag stripping to function correctly. The original code
had side effects that would make it so the workaround was active on all
MACs. I have updated the code so that the workaround is enabled, but
limited to the 82576, or activated if we exceed the available unicast
addresses.
The workaround has a side effect of mirroring all of the traffic outgoing
from the VFs back to the PF. As such it is not recommended to use the
82576 in promiscuous mode as it will take a performance hit, though this is
now consistent with the performance as seen on the out-of-tree igb driver.
I also limited the scope of the UTA bits all being set to only when the
VMOLR register is enabled. This should limit the effects of the UTA
register so that we don't pick up any excess traffic unless promiscuous
mode has been enabled on the PF, whereas before the PF would have ended up
in something equivalent to unicast promiscuous mode with VLAN filtering
otherwise.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can use the bridge utility to add a FDB
entry for the PF to an igb port. By doing this we can enable the VFs to
talk to virtual ports residing on top of the PF.
In addition this should also address issues with MACVLANs trying to reside
on top of the PF as well as they would have had similar issues when added
to the PF with SR-IOV enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch drops several checks that we dropped from ixgbe some ago. It
should not be possible for us to be called with either of the conditional
statements returning true so we can just drop them from the hot-path.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes things so that we can fully support SR-IOV or the
recently added NTUPLE filtering while allowing support for VLAN promiscuous
mode. By making this change we are able to support possible scenarios such
as SR-IOV with the PF connected to a Linux bridge hosting other VMs.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to clean-up the configuration of the VF port based VLAN
configuration. The original logic was a bit muddled and had some
undesirable side effects such as VLANs being either completely stripped
from the port or VLANs being left when they shouldn't be. The idea behind
this code is to avoid any events such as spurious spoof notifications when
we are removing one VLAN tag and replacing it with another.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can merge the configuration of the VLVF
registers into the setting of the VFTA register. By doing this we simplify
the logic and make use of similar functionality that we have already added
for ixgbe making it easier to maintain both drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that we always add VLAN 0. This is important as we
need to guarantee the PF can receive untagged frames in the case of SR-IOV
being enabled but VLAN filtering not being enabled in the kernel.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The RLPML registers already take the size of VLAN headers into account when
determining the maximum packet length. This is called out in EAS documents
for several parts including the 82576 and the i350. As such we can drop
the addition of size to the value programmed into the RLPML registers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the igb driver is using page based receive there is no point in
limiting the Rx capabilities of the device. The driver can receive 9K
jumbo frames at all times. The only changes needed due to MTU changes are
updates for the FIFO sizes and flow-control watermarks.
Update the maximum frame size to reflect the 9.5K limitation of the
hardware, and replace all instances of max_frame_size with
MAX_JUMBO_FRAME_SIZE when referring to an Rx FIFO or frame.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch starts the clean-up process on the VFTA configuration.
Specifically in this patch I attempt to address and simplify several items
while also updating the code to bring it more inline with what is already
in ixgbe.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drop a bunch of hand written byte swapping code in favor of just doing the
byte swapping ourselves. The registers are little endian registers storing
a big endian value so if we read the MAC address array as little endian
then we will get the CPU registers into the proper layout.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver shouldn't just give up if it fails to get the hardware
mailbox lock. This can happen in a situation where the PF-VF
communication channel is heavily loaded and causes complete
communications failure between the PF and VF drivers.
Add a counter and a delay. The driver will now retry ten times, waiting
one millisecond between retries.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By the commit 72ddef0506 ("igb: Fix oops caused by missing queue
pairing"), the IGB_FLAG_QUEUE_PAIRS flag can now be set when changing the
number of queues by "ethtool -L", but it is never cleared unless the igb
driver is reloaded.
This patch clears it if queue pairing becomes unnecessary as a result of
"ethtool -L".
Signed-off-by: Shota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If VFs are enabled (max_vfs >= 1), both max_rss_queues and
adapter->rss_queues are set to 2 in the case of e1000_82576.
In this case, IGB_FLAG_QUEUE_PAIRS is always set in the default block as a
result of fall-through, thus setting it in the e1000_82576 block is not
necessary.
Signed-off-by: Shota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is an opportunity to bulk free SKBs during reclaiming of
resources after DMA transmit completes in ixgbe_clean_tx_irq. Thus,
bulk freeing at this point does not introduce any added latency.
Simply use napi_consume_skb() which were recently introduced. The
napi_budget parameter is needed by napi_consume_skb() to detect if it
is called from netpoll.
Benchmarking IPv4-forwarding, on CPU i7-4790K @4.2GHz (no turbo boost)
Single CPU/flow numbers: before: 1982144 pps -> after : 2064446 pps
Improvement: +82302 pps, -20 nanosec, +4.1%
(SLUB and GCC version 5.1.1 20150618 (Red Hat 5.1.1-4))
Joint work with Alexander Duyck.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some missing reporting/advertisement of 100Mb capability
for adapters that support it.
Change-ID: I8b8523fbdc99517bec29d90c71b3744db11542ac
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new External Device Power Ability field to the get_link_status data
structure, using space from the reserved field at the end of the struct.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the name of the new cloud tunnel type from the place-holder NGE
name to the official Geneve. Also fix the spelling of the VXLAN type.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Add the AQ opcode and struct definitions for the Run PHY Activity command
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X710/XL710 devices require FW version checks to properly handle DCB
configurations from the FW. Newer devices do not, so limit these checks
to X710/XL710.
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new proxy-wake-on-lan capability bit available with the
new X722 device.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As done per ixgbe, use a private workqueue to avoid blocking the
system workqueue. This avoids some strange side effects when
some other entity is depending on the system work queue.
Change-ID: Ic8ba08f5b03696cf638b21afd25fbae7738d55ee
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add write-back on interrupt throttle rate timer expiration support
for the i40evf driver, when running on X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PCTYPES for the X710 and X722 families are different. This patch
makes adjustments for that.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds another way to access the RSS keys and lut using the AQ
for X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the KX and QSFP device IDs for X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The restart-autoneg work around does not apply to X722.
Added a flag to set it only for the right MAC and right FW version
where the work around should be applied.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Change-ID: I942c3ff40cccd1e56f424b1da776b020fe3c9d2a
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we check these ring pointers to make sure we don't double-allocate
or double-free the rings, we had better null them out after we free
them. In very rare cases this can cause a panic if the driver is removed
during reset recovery.
Change-ID: Ib06eb4910a3058275c8f7ec5ef7f45baa4674f96
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device capabilities were defined in two places, and neither had all
the definitions. It really belongs with the AQ API definition, so this
patch removes the other set of definitions and fills out the missing item.
Change-ID: I273ba7d79a476cd11d2e0ca5825fec1716740de2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some modes, bonding would not enslave VF interfaces. This is due to
bonding calling change_mtu and the immediately calling open. Because of
the asynchronous nature of the admin queue mechanism, the VF returns
-EBUSY to the open call, because it knows the previous operation hasn't
finished yet. This causes bonding to fail with a less-than-useful error
message.
To fix this, remove the check for pending operations at the beginning of
open. But this introduces a new bug where the driver will panic on a
quick close/open cycle. To fix that, we add a new driver state,
__I40EVF_DOWN_PENDING, that the driver enters when down is called. The
driver finally transitions to a fully DOWN state when it receives
confirmation from the PF driver that all the queues are disabled. This
allows open to complete even if there is a pending mtu change, and
bonding is finally happy.
Change-ID: I06f4c7e435d5bacbfceaa7c3f209e0ff04be21cc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
100M SGMII is only supported on X722. Replace the mac check with
a feature flag check that is only set for the X722 device.
Change-ID: I53452d9af6af8cd9dca8500215fbc6ce93418f52
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the Hash PCTYPE enable for X722 since it supports
a broader selection of PCTYPES for TCP and UDP.
This patch also fixes a bug in XL710, X710, X722 support for RSS,
as of now we cannot reduce the (4)tuple for RSS for TCP/IPv4/IPV6 or
UDP/IPv4/IPv6 packets since this requires a product feature change
that comes in a later release.
A VF should never be allowed to change the tuples for RSS for any
PCTYPE since that's a global setting for the device in case of i40e
devices.
Change-ID: I0ee7203c9b24813260f58f3220798bc9d9ac4a12
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add MAC filter element to the end of the list in the given order,
just to be tidy, and just in case there are ever any ordering issues in
the future.
Change-ID: Idc15276147593ea9393ac72c861f9c7905a791b4
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
intel/i40e/i40e_txrx.c: In function 'i40e_xmit_frame_ring':
intel/i40e/i40e_txrx.c:2367:20: error: 'oiph' may be used uninitialized in this function [-Werror=maybe-uninitialized]
intel/i40e/i40e_txrx.c:2317:16: note: 'oiph' was declared here
intel/i40e/i40e_txrx.c:2367:17: error: 'oudph' may be used uninitialized in this function [-Werror=maybe-uninitialized]
intel/i40e/i40e_txrx.c:2316:17: note: 'oudph' was declared here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes following build warnings :
drivers/net/ethernet/intel/i40e/i40e_main.c:7057:13: warning:
'i40e_sync_udp_filters_subtask' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8524:13: warning:
'i40e_add_vxlan_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8569:13: warning:
'i40e_del_vxlan_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8604:13: warning:
'i40e_add_geneve_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8651:13: warning:
'i40e_del_geneve_port' defined but not used [-Wunused-function]
Fixes: 6a89902405 ("i40e: geneve tunnel offload support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-01-08
This series contains updates to ixgbe only.
Vasu provides three fixes for ixgbe, first assigns a minimum credit to
a traffic class to resolve a Tx hang for CEE mode configuration. Second
fix changes the driver to use netdev->fcoe_ddp_xid instead of our local
IXGBE_FCOE_DDP_MAX, since it is correctly set for our different devices
and avoids a DDP skip error on X550. Lastly fix the PFC configuration
to include X550 devices.
Emil provides a fix for reporting the speed in ethtool by using the
stored value in out adapter structure. This is due to external drivers
may end up with unknown speed when calling ethtool_get_settings().
Mark fixes the handling of any outer UDP checksum, by passing the
skb up with CHECKSUM_NONE when an outer UDP checksum is set. This
will cause the stack to check the checksum, also do not increment an
error counter because we do not really know if there is an actual error.
Ixgbe ATR was not handling IPv6 extended headers, so ATR is not being
performed on such packets. Fix this by skipping extended headers
when they are present.
Usha fixes an issue with X550 and getting FDMI HBA attributes when
FCoE support is enabled.
Neerav fixes an issue for X550 when FCoE and SR-IOV are enabled, which
the hardware generates MDD events. Resolve this by setting the expected
values in the transmit context descriptors for FCoE/FIP frames and
adding a flush after writing the RDLEN register.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now ATR is not handling IPv6 extended headers, so ATR is not
being performed on such packets. Fix that by skipping extended
headers when they are present. This also fixes a problem where
the ATR code was not checking that the inner protocol was actually
TCP before setting up the signature rules. Since the protocol check
is intimately involved with the extended header processing as well,
this all gets fixed together.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When FCoE is enabled with SR-IOV on the X550 NIC the hardware
generates MDD events.
This patch fixes these by setting the expected values in the
Tx context descriptors for FCoE/FIP frames and adding a flush
after writing the RDLEN register.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check whether the FCOE support is enabled for the devices to get the
FDMI HBA attributes information instead of checking each device id.
Also, add Model string information for X550.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an outer UDP checksum is set, pass the skb up with CHECKSUM_NONE
so that the stack will check the checksum. Do not increment an
error counter, because we don't know that there is an actual error.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_get_settings() the link status and speed of the interface
are determined based on a read from the LINKS register via the call
to mac.ops.check.link(). This can cause issues where external drivers
may end up with unknown speed when calling ethtool_get_setings().
Instead of calling the mac.ops.check_link() we can report the speed
from the adapter structure which is populated by the driver.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PFC is configuration is skipped for X550 devices due to a incorrect
device id check, fixing that to include X550 PFC configuration.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use fcoe_ddp_xid from netdev as this is correctly set for different
device IDs to avoid DDP skip error on X550 as "xid=0x20b out-of-range"
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently credit_refill and credit_max could be zero for a TC and that
is causing Tx hang for CEE mode configuration, so to fix that have at
min credit assigned to a TC and that is as what IEEE mode already does.
Change-ID: If652c133093a21e530f4e9eab09097976f57fb12
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Somehow an ID that has never been productized is in the
code. There are no plans to use it, so just get
rid of it.
Change-ID: I59117d48ea9ee0360b0fe33833ac8092f8a24b4c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver calls skb_set_hash even with a zero hash, that
indicates to the stack that the hash calculation is offloaded
in hardware. So the Stack doesn't do a SW hash which is required
for load balancing if the user decides to turn of rx-hashing
on our device.
This patch fixes the path so that we do not call skb_set_hash
if the feature is disabled.
Change-ID: Ic4debfa4ff91b5a72e447348a75768ed7a2d3e1b
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the i40e equivalent of commit c762dff24c ("ixgbe: Look up MAC
address in Open Firmware or IDPROM").
As with that fix, attempt to look up the MAC address in Open Firmware
on systems that support it, and use IDPROM on SPARC if no OF address
is found.
In the case of the i40e there is an assumption that the default mac
address has already been set up as the primary mac filter on probe,
so if this filter is obtained from the Open Firmware or IDPROM, an
explicit write is needed via i40e_aq_mac_address_write() and
i40e_aq_add_macvlan() invocation.
The I40E_FLAG_PF_MAC flag in the platform-private i40e_pf structure
tracks whether a platform-specific mac address was found, in which
case calls to i40e_aq_mac_address_write() and i40e_aq_add_macvlan()
will be triggered.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow the user to specify a zero MAC address for VFs. This removes the
existing MAC address and allows the VF to use a random address. Libvirt
does this normally when removing a VF from a VM.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VFs are being reset, there is a brief window of time when they
cannot be configured because they don't have a VSI to configure. If
a script is quick, it can fall through that window. To avoid
defenestration, log a useful error message and return -EAGAIN.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When I had rewritten the code for ixgbe_clear_vf_vlans() it looks like I
had transitioned back and forth between using word as an offset and using
word as a register offset. As a result I honestly don't see how the code
was working before other than the fact that resetting the VLANs on the VF
like didn't do much to clear them.
Another issue found is that the mask was using a divide instead of a
modulus. As a result the mask bit was incorrectly being set to either bit
0 or 1 based on the value of the VF being tested. As a result the wrong
VFs were having their VLANs cleared if they were enabled.
I have updated the code so that word represents the offset in the array.
This way we can use the modulus and xor operations and they will make sense
instead of being performed on a 4 byte aligned value.
I replaced the statement "(word % 2) ^ 1" with "~word % 2" in order to
reduce the line length as the line exceeded 80 characters with the register
name inserted. The two should be equivalent so the change should be safe.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x revision check needs to check a value, not just a bit.
Use a mask and check the value. Also remove the redundant check
inside the ixgbe_enter_lplu_t_x550em, because it can only be called
when both the mac type and revision check pass.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 allows for up to 64 RSS queues, but the driver can have max
of 63 (-1 MSIX vector for link).
On systems with >= 64 CPUs the driver will set the redirection table
for all 64 queues which will result in packets being dropped.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up minor redundancy in the setting of hw_enc_features that
makes it appears that X550 uniquely has more encapsulation features
than other devices. The driver only supports one more feature, so
make it look that way. No longer set NETIF_F_SG since that is set
by the register_netdev call. Thanks to Alex Duyck for noticing this
slight confusion.
Reported-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the
backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add missing QSFP PHY types to allow for more accurate reporting of
port settings.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
adapter->rx_itr_setting is not a mask so check it with == instead of &
do not default to 12K interrupts in ixgbevf_set_itr()
There should be no functional effect from these changes.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the same patch as for ixgbe but applied differently according to
busy polling. See commit 5d6002b7b8 ("ixgbe: Fix handling of NAPI
budget when multiple queues are enabled per vector")
Signed-off-by: William Dauchy <william@gandi.net>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tri-states need 'if IS_ENABLED()', booleans should use 'ifdef'.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup a number of issues with function header comments, lower-case
acronyms (i.e. FIFO, TLV), duplicate comments and a stubbed-out header
comment for fm10k_sm_mbx_init.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These structures never change so declare them as const.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When comparing MAC addresses, use ether_addr_equal instead of memcmp to
ETH_ALEN length. Found and replaced using the following sed:
sed -e 's/memcmp\x28\(.*\), ETH_ALEN\x29/!ether_addr_equal\x28\1\x29/'
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to cleanup the exception handling for the paths where
we reset the interrupts and then reconfigure them. In all of these paths
we had very different levels of exception handling. I have updated the
driver so that all of the paths should result in a similar state if we
fail.
Specifically the driver will now unload the mailbox interrupt, free the
queue vectors and MSI-X, and then detach the interface.
In addition for any of the PCIe related resets I have added a check with
the hw_ready function to just make sure the registers are in a readable
state prior to reopening the interface.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The TLV format for little endian structures is actually 4 byte aligned
copy. To this end, we need to add an additional __aligned(4) marker
along with __packed to ensure that these structures are actually 4 byte
aligned and packed correctly. Use of just __packed will not work as this
will result in 1byte alignment which is incorrect. Add a comment
explaining the reasoning behind why these structures need the special
treatment.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleans up checkpatch GLOBAL_INITIALIZERS error
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to geneve_get_rx_port in i40e so that when it
comes up it can learn about the existing geneve tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Kconfig file with dependency for supporting GENEVE tunnel
offloads.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver hooks to implement ndo_ops to add/del
udp port in the HW to identify GENEVE tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the introduction of 82574 support in e1000e, the driver has worked
on the assumption that msi-x interrupt generation is automatically
disabled after each irq. As it turns out, this is not the case.
Currently, rx interrupts can fire multiple times before and during napi
processing. This can be a problem for users because frames that arrive
in a certain window (after adapter->clean_rx() but before
napi_complete_done() has cleared NAPI_STATE_SCHED) generate an interrupt
which does not lead to napi_schedule(). These frames sit in the rx queue
until another frame arrives (a tcp retransmit for example).
While the EIAC and CTRL_EXT registers are properly configured for irq
automask, the modification of IAM in e1000_configure_msix() is what
prevents automask from working as intended.
This patch removes that erroneous write and fixes interrupt rearming for
tx interrupts. It also clears IAME from CTRL_EXT. This is not strictly
necessary for operation of the driver but it is to avoid disruption from
potential programs that access the registers directly, like `ethregs -c`.
Reported-by: Frank Steiner <steiner-reg@bio.ifi.lmu.de>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In msi-x mode, there is no handler for the lsc interrupt so there is no
point in writing that to ics now that we always assume Other interrupts
are caused by lsc.
Reviewed-by: Jasna Hodzic <jhodzic@ucdavis.edu>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removes the ICR read in the other interrupt handler, uses EIAC to
autoclear the Other bit from ICR and IMS. This allows us to avoid
interference with Rx and Tx interrupts in the Other interrupt handler.
The information read from ICR is not needed. IMS is configured such that
the only interrupt cause that can trigger the Other interrupt is Link
Status Change.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
msi-x interrupts are not shared so there's no need to check if the
interrupt was really from this adapter.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the ethtool self-test gstrings/data arrays were accessed via
hardcoded indices, which made the code difficult to follow. This patch
replaces the hardcoded values with enum-based labels.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the PHY-specific code to get the cable length for the
I210 internal and related PHYs was reporting the cable length of a
single pair and reporting it as the min, max, and total cable length.
Update it so that all four pairs are checked so the true min, max,
and average cable lengths are reported.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reason to add the PHY address into the PCDL register address.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I210 internal PHY can be accessed just as well with the access
functions shared by 82580, I350, and I354 devices. A side effect of
relying on the common functions, is that I210 cable length support
is folded back into the common case which effectively reverts the
following commit:
commit 59f301046b
Author: Carolyn Wyborny <carolyn.wyborny@intel.com>
Date: Wed Oct 10 04:42:59 2012 +0000
igb: Update get cable length function for i210/i211
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function e1000e_up always returns 0. As such we can convert it to a
void and just ignore the results. This allows us to drop some code in a
couple spots as we no longer need to worry about non-zero return values.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to ixgbe and i40e, initialize XPS on driver load so that we can
take advantage of this kernel feature.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make functions that should be static. While we're at it, fix the function
header comment for fm10k_tlv_attr_nest_stop(), and update the copyright
header for fm10k_pf.h, fm10k_tlv.c and fm10k_tlv.h.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function declaration does not need to be 'inline'd here.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses two issues.
First is the fact that the fm10k_mbx_free_irq was assuming msix_entries was
valid and that will not always be the case. As such we need to add a check
for if it is NULL.
Second is the fact that we weren't freeing the IRQ if the mailbox API
returned an error on trying to connect.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the q_vector allocation fails we should free the resources associated
with the MSI-X vector table.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rather than wrapping fm10k_dcbnl.c and fm10k_debugfs.c support with
#ifdef blocks, just conditionally include the .o files in the Makefile.
Also, since we're modifying it, update the copyright year on the
Makefile.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We haven't bumped the driver version in a while despite many fixes being
pulled in from the out-of-tree Sourceforge driver. Update the version to
match.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using lowercase vlan, vid, or VID, always use VLAN or VLAN ID
in comments when referring to VLANs. The original driver code was
consistent, but recent patches have not been as consistent with this
naming scheme.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Improve code style by removing the unnecessary else block of an if
statement which immediately returns.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid the use of CamelCase for some variable names that previously
slipped through review.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the ether_addr_copy function instead of copying byte-by-byte in a
for-loop by hand.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2015-12-12
This series contains updates to e1000, e1000e and igb.
Joern Engel fixes up the e1000 driver to reduce scheduler latencies by
making the eeprom read/write functions scheduler friendly by using a mutex
lock instead of a spin lock.
Todd adds code for igb to initialize the 88E1543 PHY properly. Then fixed
igb to use the correct i210 register for EEMNGCTL, since the i210 has two
EEPROM access registers (EEARBC and EEMNGCTL).
Dmitry Vyukov provides a fix for e1000 to resolve a data race found with
KernelThreadSanitizer (KTSAN), where no memory barriers were being used
when buffers get recycled, so the recycled buffers can be corrupted. So
use smp_store_release() to update tx_ring->next_to_clean and
smp_load_acquire() to read tx_ring->next_to_clean to properly hand off
buffers from e1000_clean_tx_irq() to e1000_xmit_frame().
Jarod Wilson fixes igb so that we do not try to unmap a NULL hw_addr. Then
cleaned up array_rd32() so that it uses igb_rd32() the same as rd32() and
use io_addr() in more places so that we do not have to call E1000_REMOVED().
Janusz Wolak cleans up the e1000 driver by correcting warnings produced
by checkpatch.pl for the driver.
Jean Sacren provides several patches with general cleanups for e1000 and
e1000e, which include code comment fix-ups and cleanup of local variables
not needed.
Dmitry Fleytman fixes a possible division by zero in the receive interrupt
handler for e1000e when working without adaptive interrupt moderation,
which is typically disabled on jumbo MTUs.
Raanan increases the timeout of the polling bit due to timing changes to
the ME firmware on a platform, so increase the timeout to 300ms. Added
initial support for i219-LM, which is a LOM that will be available on
systems with the Lewisburg Platform Controller HUB (PCH) chipset.
Jan Beulich fixes a NULL dereference in igb, due to the adapter->vf _data
being NULL while adapter->vfs_allocated_count is non-zero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
i219-LM (3) is a LOM that will be available on systems with the
Lewisburg Platform Controller Hub (PCH) chipset from Intel.
This patch provides the initial support for the device.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up array_rd32 so that it uses igb_rd32 the same as rd32, per the
suggestion of Alexander Duyck, and use io_addr in more places, so that
we don't have the need to call E1000_REMOVED (which simply looks for a
null hw_addr) nearly as much.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The combined effect of commits 6423fc3416 ("igb: do not re-init SR-IOV
during probe") and ceee3450b3 ("igb: make sure SR-IOV init uses the
right number of queues") causes VFs no longer getting set up, leading
to NULL pointer dereferences due to the adapter's ->vf_data being NULL
while ->vfs_allocated_count is non-zero. The first commit not only
neglected the side effect of igb_sriov_reinit() that the second commit
tried to account for, but also that of setting IGB_FLAG_HAS_MSIX,
without which igb_enable_sriov() is effectively a no-op. Calling
igb_{,re}set_interrupt_capability() as done here seems to address this,
but I'm not sure whether this is better than sinply reverting the other
two commits.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to timing changes to the ME firmware in Skylake, this timer
needs to be increased to 300ms.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes possible division by zero in receive
interrupt handler when working without adaptive interrupt
moderation.
The adaptive interrupt moderation mechanism is typically
disabled on jumbo MTUs.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Leonid Bloch <leonid@daynix.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By using goto statement, we can achieve sharing the same exit path so
that code duplication could be minimized.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to historical reason, 'phy_data' has never been included in the
kernel doc. Fix it so that the requirement could be fulfilled.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The local variable 'ret' doesn't serve much purpose so we might as well
clean it up.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use 'That' to replace 'The' so that the comment would make sense.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The checking logic needed some clean-up work, so we rewrite it by
checking for break first. With that change in place, we can even move
the second check for goto statement outside of the loop.
As this is merely a cleanup, no functional change is involved. The
questionable 'tmp != 0xFF' is intentionally left alone.
Mark Rustad and Alexander Duyck contributed to this patch.
CC: Mark Rustad <mark.d.rustad@intel.com>
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i210 has two EEPROM access registers that are located in
non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously
and EEMNGCTL should also be corrected.
Reported-by: Roman Hodek <roman.aud@siemens.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Janusz Wolak <januszvdm@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000_clean_tx_irq cleans buffers and sets tx_ring->next_to_clean,
then e1000_xmit_frame reuses the cleaned buffers. But there are no
memory barriers when buffers gets recycled, so the recycled buffers
can be corrupted.
Use smp_store_release to update tx_ring->next_to_clean and
smp_load_acquire to read tx_ring->next_to_clean to properly
hand off buffers from e1000_clean_tx_irq to e1000_xmit_frame.
The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Code was responsible for ~150ms scheduler latencies.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Generate version strings like the PF driver does. This gives us more
flexibility to add suffixes to the version string at build time.
Change-ID: I0a5ca0783dd8fb849516bfc1e37ea070127847bd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean the whole mac filter list when resetting after an intermediate
add or delete push to the firmware. The code had evolved from using
a list from the stack to a heap allocation, but the memset() didn't
follow the change correctly. This now cleans the whole list rather
that just part of the first element.
Change-ID: I4cd03d5a103b7407dd8556a3a231e800f2d6f2d5
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports Expanded version of TCP, UDP PCTYPES for RSS.
Add a Virtchnl offload to support this.
Without this patch with X722 devices, driver will set wrong PCTYPES
for VF and UDP flows will not fan out.
Change-ID: I04fe4988253b7cd108c9179a643c969764efcb76
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These messages seem big and scary, but they're really not. The driver
can fully recover from any of these. The overflow error in particular
can happen when enabling a bunch of VFs and the VF driver is not
blacklisted.
Since these messages are really for debugging purposes, reclassify
them as such.
Change-ID: I628d0f5e135e7063450ba05393a50b7af23aa6d7
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a part of implementation which contains data structures and
opcode for new AQ command. There's a new ARQ message that gets sent
near the end of the NVM update process that the driver should recognize
and ignore, rather than printing an Unknown Event error.
Change-ID: I04830a5bcae14823e16b9424cc4165e169336c1f
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver gets unloaded during reset recovery, it's possible
that it will attempt to free resources when they're already free.
Add a check to make sure that the Tx and Rx rings actually exist
before dereferencing them to free resources.
Change-ID: I4d2b7e9ede49f634d421a4c5deaa5446bc755eee
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VFs are created, the MAC address defaults to all zeros, indicating
to the VF driver that it should use a random MAC address. However, the
PF driver was incorrectly adding this zero MAC to the filter table,
along with the VF's randomly generated MAC address.
Check for a good address before adding the default filter. While we're
at it, make the error message a bit more useful.
Change-ID: Ia100947d68140e0f73a19ba755cbffc3e79a8fcf
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtual channel interface was using incorrect semantics to remove
MAC addresses, which would leave incorrect filters active when using
VLANs. To correct this, add a new function that unconditionally removes
MAC addresses from all VLANs, and call this function when the VF
requests a MAC filter removal.
Change-ID: I69826908ae4f6c847f5bf9b32f11faa760189c74
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BIT_ULL was used on a u32 or less where it can simply be BIT. This
fixes some trivial static analyzer warnings. Chomp, chomp.
Tested with objdump of binary before and after, no changes to code.
Change-ID: I6245e9abd447192dbde1669c747aeb2878126c7d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some X550 devices can connect at 2.5Gbps during fail-over, but only
with certain link partners. Also setting the advertised speed will
not work so we do not report it as supported to avoid confusion.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch guarantees that the VFs do not have access to VLANs that they
were not supposed to. What this patch does is add code so that we delete
the previous port VLAN after adding a new one, and if we reset the VF we
clear all of the filters associated with it.
Previously the code was leaving all previous VLANs mapped to the VF and
they didn't get deleted unless the VF specifically requested it or if the
PF itself was reset.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes certain that we clear the pool mappings added when we
configure default MAC addresses for the interface. Without this we run the
risk of leaking an address into pool 0 which really belongs to VF 0 when
SR-IOV is enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a follow-on for enabling VLAN promiscuous and allowing the PF
to add VLANs without adding a VLVF entry. What this patch does is go
through and free the VLVF registers if they are not needed as the VLAN
belongs only to the PF which is the default pool.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for VLAN promiscuous with SR-IOV enabled.
The code prior to this patch was only adding the PF to VLANs that the VF
had added. As such enabling promiscuous mode would actually not add any
additional VLAN filters so visibility was limited. This lead to a number
of issues as the bridge and OVS would expect us to accept all VLAN tagged
packets when promiscuous mode was enabled, and instead we would filter out
most if not all depending on the configuration of the PF.
With this patch what we do is set all the bits in the VFTA and all of the
VLVF bits associated with the pool belonging to the PF. By doing this the
PF is guaranteed to receive all VLAN tagged traffic associated with the RAR
filters assigned to the PF. In addition we will clean up those same bits
in the event of promiscuous mode being disabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to reduce the complexity of the search function used
for finding a VLVF entry associated with a given VLAN ID. The previous
code was searching from bottom to top. I reordered it to search from top
to bottom. In addition I pulled an AND statement out of the loop and
instead replaced it with an OR statement outside the loop. This should
help to reduce the overall size and complexity of the function.
There was also some formatting I cleaned up in regards to whitespace and
such.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for bypassing the VLVF entry creation when the PF
is adding a new VLAN. The advantage to doing this is that we can then save
the VLVF entries for the VFs which must have them in order to function,
versus the PF which can fall back on the default pool entry.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses several issues within the VLVF and VLVFB
configuration
First was the fact that code was overly complicated with multiple
conditional paths depending on if we adding or removing and which bit we
were going to add or remove. Instead of messing with all that I have
simplified it by using (vid / 32) and (1 - vid / 32) to identify our
register and the other vlvfb register.
Second was the fact that we were likely leaking a few packets into the PF
in cases where we were deleting an entry and the VFTA filter for that entry
as the ordering was such that we deleted the pool and then the VLAN filter
instead of the other way around. I have updated that by adding a check for
no bits being set and if that occurs we clear things up in the proper
order.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to clear the way for upcoming work I thought it best to drop the
level of indent in the ixgbe_set_vfta_generic function. Most of the code
is held in the virtualization specific section. So the easiest approach is
to just add a jump label and jump past the bulk of the code if it is not
enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the logic for setting the VFTA register by removing
the number of conditional checks needed. Instead we just use some boolean
logic to generate vfta_delta, and if that is set then we xor the vfta by
that value and write it back.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code for checking the PF bit in ixgbe_set_vf_vlan_msg was using the
wrong offset and as a result it was pulling the VLAN off of the PF even if
there were VFs numbered greater than 40 that still had the VLAN enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a check to make certain mac_table was actually allocated and is not
NULL. If it is NULL return -ENOMEM and allow the probe routine to fail
rather then causing a NULL pointer dereference further down the line.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fix multiple spelling typos found in
various part of kernel.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 8fe269991a.
The case where VXLAN is a module and i40e driver is inbuilt
will not be handled properly with this change since i40e
will have an undefined symbol vxlan_get_rx_port in it.
v2: Add a signed-off-by.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current default ITR for Tx is overly restrictive. Using a simple
netperf TCP_STREAM test, we top out at about 10Gb/s for a single thread
when running using 1500 byte frames. By reducing the ITR value to 25usec
(up to 40K interrupts a second from 10K), we are able to achieve 36Gb/s
for a single thread TCP stream test.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing adaptive ITR algorithm is overly restrictive. It throttles
incorrectly for various traffic rates, and does not produce good
performance. The algorithm now allows for more interrupts per second,
and does some calculation to help improve for smaller packet loads. In
addition, take into account the new itr_scale from the hardware which
indicates how much to scale due to PCIe link speed.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Reported-by: Alex Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Define a macro for identifying when the itr value is dynamic or
adaptive. The concept was taken from i40e. This helps make clear what
the check is, and reduces the line length to something more reasonable
in a few places.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Intel Ethernet Switch FM10000 Host Interface interrupt throttle
timers are based on the PCIe link speed. Because of this, the value
being programmed into the ITR registers must be scaled accordingly.
For the PF, this is as simple as reading the PCIe link speed and storing
the result. However, in the case of SR-IOV, the VF's interrupt throttle
timers are based on the link speed of the PF. However, the VF is unable
to get the link speed information from its configuration space, so the
PF must inform it of what scale to use.
Rather than pass this scale via mailbox message, take advantage of
unused bits in the TDLEN register to pass the scale. It is the
responsibility of the PF to program this for the VF while setting up the
VF queues and the responsibility of the VF to get the information
accordingly. This is preferable because it allows the VF to set up the
interrupts properly during initialization and matches how the MAC
address is passed in the TDBAL/TDBAH registers.
Since we're modifying fm10k_type.h, we may as well also update the
copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Originally this statistic was renamed because the method of dropping was
called "drop_oversized_messages", but this logic has changed much, and
this counter does actually represent messages which we failed to
transmit for a number of reasons. Rename the counter back to tx_dropped
since this is when it will increment, and it is less confusing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous bug was uncovered by addition of a debug stat to indicate the
actual number of DWORDS we pulled from the mbmem. It turned out this was
not the same as the tx_dwords counter. While the previous bug fix should
have corrected this in all cases, add some debug stats that count the
number of DWORDs pushed or pulled from the mbmem. A future debugger may
take advantage of this statistic for debugging purposes. Since we're
modifying fm10k_mbx.h, update the copyright year as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the resultant data type of the mac_update.mac_upper field is u16,
it does not make sense to typecast u8 variables to u32 first. Since
we're modifying fm10k_pf.c, also update the copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The init_hw function may fail, and in the case of VFs, it might change
the number of maximum queues available. Thus, for every flow which
checks init_hw, we need to ensure that we clear the queue scheme before,
and initialize it after. The fm10k_io_slot_reset path will end up
triggering a reset so fm10k_reinit needs this change. The
fm10k_io_error_detected and fm10k_io_resume also need to properly clear
and reinitialize the queue scheme.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change modified init_hw in some flows the function may fail on
VF devices. For example, if a VF doesn't yet own its own queues.
However, many callers of init_hw didn't bother to check the error code.
Other callers checked but only displayed diagnostic messages without
actually handling the consequences.
Fix this by (a) always returning and preventing the netdevice from going
up, and (b) printing the diagnostic in every flow for consistency. This
should resolve an issue where VF drivers would attempt to come up
before the PF has finished assigning queues.
In addition, change the dmesg output to explicitly show the actual
function that failed, instead of combining reset_hw and init_hw into a
single check, to help for future debugging.
Fixes: 1d568b0f6424 ("fm10k: do not assume VF always has 1 queue")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF drivers must detect how many queues are available. Previously, the
driver assumed that each VF has at minimum 1 queue. This assumption is
incorrect, since it is possible that the PF has not yet assigned the
queues to the VF by the time the VF checks. To resolve this, we added a
check first to ensure that the first queue is infact owned by the VF at
init_hw_vf time. However, the code flow did not reset hw->mac.max_queues
to 0. In some cases, such as during reinit flows, we call init_hw_vf
without clearing the previous value of hw->mac.max_queues. Due to this,
when init_hw_vf errors out, if its error code is not properly handled
the VF driver may still believe it has queues which no longer belong to
it. Fix this by clearing the hw->mac.max_queues on exit due to errors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't change netdev hw_features later in fm10k_probe, instead set all
values inside fm10k_alloc_netdev. To do so, we need to know the MAC type
(whether it is PF or VF) in order to determine what to do. This helps
ensure that all logic regarding features is co-located.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver were to happen to have a mutex held while
the i40e_init_adminq call was called, the init_adminq might
inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantics.
Fix this by avoiding adminq.c code allocating/freeing this memory, and
then do the same work only once in probe/remove.
Testing Hints (Required if no HSD): for VF, load i40evf in bare metal
and echo 32 > sriov_numvfs; echo 0 > sriov_numvfs in a loop. Yes this
is a horrible thing to do.
Change-ID: Ida263c51b34e195252179e7e5e400d73a99be7a2
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state. Specifically the MAC address was
enabled for both VF 0 and the PF. This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.
A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.
In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.
Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000
Result:
MPSAR[0] 00000081
MPSAR[254] 00000001
Expected Result, behavior after patch:
MPSAR[0] 00000080
MPSAR[254] 00000080
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to i40e and i40evf only.
Mitch updates the i40evf driver by increasing the maximum number of queues,
since future devices will allow for more queue pairs. Cleans up a
duplicate printing of the driver info string done in init, since it is
already done in probe. Cleaned up the several allocations which did
not need to be at atomic level, where GFP_KERNEL would work just fine.
Then makes i40e_sync_vsi_filters() a more mature function, make having
a common exit point so it will properly release the busy lock on the VSI
and propagate errors to the callers. Then does some whitespace
housekeeping in i40evf.
Kiran moves and updates the detection/recovery of transmit queue hang code
to service_task from tx_timeout function. Also fixed memory leak when
users program flow-director filter using ethtool (sideband filter
programming), the cause being the check of 'tx_buffer->skb' was preventing
'raw_buf' from being freed as part of the cleanup.
Jesse enabled the ability to turn off/on packet split using ethtool priv
flags. Then does some housekeeping for both the i40e and i40evf drivers
which includes: remove unused/useless code, correct whitespace, remove
duplicate #include, fix incorrect comment, etc...
Neerav cleans up functions to gather Flow Control Rx XOFF stats, since
the recent change in the driver logic for checking transmit hang has been
moved, so these functions do not do anything meaningful any longer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7fd89545f3 ("i40e: remove BUG_ON from feature string building")
added defective output when I40E_FLAG_VEB_MODE_ENABLED was set in
function i40e_print_features.
Fix it.
Miscellanea:
- Remove unnecessary string variable
- Add space before not after fixed strings
- Use kmalloc not kzalloc
- Don't initialize i to 0, use result of first snprintf
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for seeing how to coalesce the error handling
into one location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of inhibiting PHY power control when manageability is
present, only inhibit turning PHY power off when manageability
is present. Consequently, PHY power will always be turned on when
requested. Without this patch, some systems with X540 or X550
devices in some conditions will never get link.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the datasheets, the driver should wait for the master
disable bit to read as being set before checking the status
register for master disable.
Reported-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver was violating the specification in the datasheet
by not waiting 1ms before checking for the reset bit clearing. This
is called out for devices supported by ixgbe, so implement the
required delay.
Reported-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we allow the PF to make use of all free RAR
entries for FDB use if needed.
Previously the code limited us to 16 unicast entries, however this was
shared between MACVLAN which wasn't limited and the FDB code which was. So
instead of treating the FDB code as a second class citizen I have updated
it so that it has access to just as many entries as the MACVLAN filters.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode
with a call to __dev_uc_sync instead. This works much better with the MAC
addr list code that was already in place and solves an issue in which you
couldn't remove an FDB address without having to reset the port.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the process of tracking down a memory leak when adding/removing FDB
entries I had to go through the MAC address configuration code for ixgbe.
In the process of doing so I found a number of issues that impacted
readability and performance. This change updates the code in general to
clean it up so it becomes clear what each step is doing. From what I can
tell there a couple of bugs cleaned up in this code.
First is the fact that the MAC addresses were being double counted for the
PF. As a result once entries up to 63 had been used you could no longer
add additional filters.
A simple test case for this:
for i in `seq 0 96`
do
ip link add link ens8 name mv$i type macvlan
ip link set dev mv$i up
done
Test script:
ethregs -s 0:8.0 | grep -e "RAH" | grep 8000....$
When things are working correctly RAL/H registers 1 - 97 will be consumed.
In the failing case it will stop at 63 and prevent any further filters from
being added.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make some minor cleanups, such as simplifying return paths, deleting
unneeded initializations, return values more directly and so forth.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The newer copper PHY implementation used with newer X550EM_x
devices uses a different thermal alarm type than the earlier
one. Make changes to support both types.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes KR PHY reset from ixgbe_init_phy_ops_x550em,
since this function is meant to initialize function pointers for
the detected PHY type. Internal PHY reset was moved to
ixgbe_setup_internal_phy_t_x550em which will now detect which
mode the internal PHY operates in and set it up as required.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) remove duplicate include of tcp.h
2) put an ampersand at the end of a line instead of the beginning
3) remove a useless dev_info
4) match declaration of function to the implementation
5) repair incorrect comment
6) correct whitespace
7) remove unused define
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shouldn't be using a bitwise operator here; it's not a bitwise
operation. Use a logical operator instead. Why doesn't c have a
logical-or-and-assign operator?
Change-ID: Id84f3ca884910bed7073c84b1e16a102e958d0de
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Operators should have spaces around them.
Change-ID: I64735e9aa8618b9a5059a87ace1c999d6d3bfcfb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The separate functions to gather Flow control Rx XOFF stats was to
determine if the Tx for a queue was paused due to Link Flow Control(LFC)
or Priority Flow Control(PFC).
But, with recent change in the i40e driver the logic for checking th Tx
hang has been removed and these functions don't do anything meaningful.
Hence, there is no need to keep these separate functions to gather Rx
XOFF stats for LFC or PFC.
This patch removes these functions and moves the stat collection for
XOFF Rx to the i40e_update_pf_stats() that collects all the PF stats.
Change-ID: Iec1452dac3a6766f0d968e754cb407530d7c60cd
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of having our own custom symbol, we can just rely
on whether or not the kernel has the feature enabled.
In this case use IS_ENABLED(CONFIG_VXLAN) in order to handle
built-in or module in the current BKM way.
Change-ID: I5890fbb518ff8ed6bb07c3362fb0a8a829f9b241
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool priv flags implementation to enable or disable packet split, which
is a hardware feature that inspects headers and will put headers in a
separate DMA buffer from the payload data. The driver was automatically
choosing to enable packet split in some cases and this gives the user the
ability to turn it off/on explicitly.
to query state:
ethtool --show-priv-flags ethx
to enable:
ethtool --set-priv-flags ethx packet-split on
to disable:
ethtool --set-priv-flags ethx packet-split off
Why would anyone want this?
Because some environments benefit from header/data split in the receive
buffer, and the driver defaults to one or the other depending on
environment/kernel parameters.
Why didn't you implement a generic ethtool control for this feature?
Because Intel hardware is the only hardware that supports header/data
split.
Change-ID: I803121e1eecc9ccb2884031fd85dd1110b3af66d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't use uint32_t type the kernel. Use u32 instead. No functional
change.
Change-ID: I77bbf3b6464edaef747c7104b43534032a4dba63
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_sync_vsi_filters() is the surly teenager of this driver. It says
it's going to report errors, but it doesn't actually do that most of the
time. And when it does, it leaves a mess.
Change this function to have a common exit point so it will properly
release the busy lock on the VSI. Propagate errors to the callers.
Finally, adjust a few callers to check for and deal with errors from
this function.
Change-ID: Ic6af4956491e72402ebb3c538a3c31a0ad7f8667
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These allocations don't need to be at atomic level. GFP_KERNEL is fine
and they'll reduce stress on the allocator when the system is starved
for memory.
Change-ID: I3561d0399a681de0ad25291b6c848b224c1fde12
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the memory leak which would be seen otherwise when user
programs flow-director filter using ethtool (sideband filter programming).
When ethtool is used to program flow directory filter, 'raw_buf' gets
allocated and it is supposed to be freed as part of queue cleanup. But
check of 'tx_buffer->skb' was preventing it from being freed.
Change-ID: Ief4f0a1a32a653180498bf6e987c1b4342ab8923
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains following changes:
- detection and recovery logic (issue SW interrupt) has been moved to
service_task from timeout function.
- added some more debug info from tx_timeout.
Logic to detect and recover TX queue hung is now two step process:
- service_task detects TX queue hung and sets a bit(hung_detected) if
it was not set.
- if bit was set (means this is back-back hung condition detected),
issue SW interrupt and clear the bit.
- napi_poll clears the bit unconditionally since it cleans TX/RX queues.
Change-ID: Ieed03a48927c845a988b3ff375090bf37caeb903
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We already print the driver info string in probe, so don't print
it again in init. No need to repeat. No need to repeat.
Change-ID: Ief597997f580a8c54d5950e3a84c29f2075be66b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the helper function to set the real number of RX queues, and also
set the real number of TX queues.
Change-ID: I67982799de3f248fb4158ccdc9b1a74385f42ddd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Future devices will allow for more queue pairs, so allocate a netdev
that can handle them. While we're at it, get rid of the separate
MAX_TX/MAX_RX defines. Since we always get matched queue pairs, having
these makes no sense.
Change-ID: I0e3556cd9a962506e509eb7c0afa36b329e8cb51
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the final edition of the patches to remove sleeps from
the driver's entry points, the grab_rtnl argument is no
longer needed, so partially revert the commit that added it.
Change-ID: Ib9778476242586cc9e58b670f5f48d415cb59003
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of awkwardly keeping a fixed array of pointers in the adapter
struct and then allocating ring structs individually, just keep a single
pointer and allocate a single blob for the arrays. This simplifies code,
shrinks the adapter structure, and future-proofs the driver by not
limiting the number of rings we can handle.
Change-ID: I31334ff911a6474954232cfe4bc98ccca3c769ff
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the queue_vector array from a statically-sized member of the
adapter structure to a dynamically-allocated and -sized array.
This reduces the size of the adapter structure, and allows us to support
any number of queue vectors in the future without changing the code.
Change-ID: I08dc622cb2f2ad01e832e51c1ad9b86524730693
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If, upon a midnight dreary, the PF returns ERR_PARAM when the VF is
requesting resources, that's fatal. Either the firmware or NVM is badly,
badly misconfigured, or this VF has been disabled due to a previous VF
driver sending a bunch of bogus messages.
Either way, there is no recovery from this. Don't ponder weak and weary,
just quit.
Change-ID: I09d9f16cc4ee7fec3b57646a289d33838c1c5bf5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we get an invalid message from a VF, we should tell the user which VF
is being naughty, rather than making them guess.
Change-ID: I9252cef7baea3d8584043ed6ff12619a94e2f99c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the confusing kernel message of enabled RSS size,
by reporting it together with the hardware maximum RSS size.
Change-ID: I64864dbfbc13beccc180a7871680def1f3d5a339
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where adminq init failures always provided
a message that NVM was newer than expected. This is not always the
case for init_adminq failures. Without this patch, if adminq init
fails for any reason, newer NVM message would be given. This
problem is fixed by adding a check for that specific error
condition and a different hopefully helpful message otherwise.
Change-ID: Iaeaebee4e398989eae40bb70f943ab66a3a521a5
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new fields to i40e_vsi to store user configured
RSS config data and code to use it.
Change-ID: Ic5d3db8d9df52182b560248f8cdca9c5c7546879
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two ways to get RSS, this patch implements two functions
with the same input parameters, and creates a more generic function
for getting RSS configuration.
Change-ID: I12d3b712c21455d47dd0a5aae58fc9b7c680db59
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two ways to configure RSS, this patch adjusts those two
functions with the same input parameters, and creates a more
generic function for configuring RSS.
Change-ID: Iace73bdeba4831909979bef221011060ab327f71
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames old VF adapter specific RSS function to clarify
its scope.
Change-ID: Ie5253083a44c677ebb7709a8a3a18402ad2dc6a6
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Issue a prefetch for data early in the transmit path.
This should not be generally needed for Tx traffic, but
it helps immensely for pktgen workloads and should help
for forwarding workloads as well.
Change-ID: Iefee870c20599e0c4240e1d8637e4f16b625f83a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue of forcing WB too often causing us to not
benefit from NAPI.
Without this patch we were forcing WB/arming interrupt too often taking
away the benefits of NAPI and causing a performance impact.
With this patch we disable force WB in the clean routine for X710
and XL710 adapters. X722 adapters do not enable interrupt to force
a WB and benefit from WB_ON_ITR and hence force WB is left enabled
for those adapters.
For XL710 and X710 adapters if we have less than 4 packets pending
a software Interrupt triggered from service task will force a WB.
This patch also changes the conditions for setting RS bit as described
in code comments. This optimizes when the HW does a tail bump amd when
it does a WB. It also optimizes when we do a wmb.
Change-ID: Id831e1ae7d3e2ec3f52cd0917b41ce1d22d75d9d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames rss_size to alloc_rss_size in i40e_pf, which is
clearer and avoids confusion. It also adds comments to the other
related structure members to help clarify usage.
Change-ID: Ia90090609d006ab589cb639975bb8a0af795d16f
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new fields to i40e_vsi to store user configured
RSS config data and code to use it.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Change-ID: I73886469dca9e9f6b16d842182a87f3f4009f95d
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames the old pf-specific function in order to clarify
its scope. This patch also creates a more generic configure RSS
function with the old name.
This patch also creates a new more generic function to get RSS
configuration, using the appropriate method.
Change-ID: Ieddca2707b708ef19f1ebccdfd03a0a0cd63d3af
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adjust the RSS configure functions so that there is a generic way to
hook to ethtool hooks.
Change-ID: If446e34fcfaf1bc3320d9d319829a095b5976e67
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where using ethtool rxnfc command could
let RX flow hash be set on disabled queues. This patch fixes the
problem by returning the number of enabled queues before setting
rxnfc.
Change-ID: Idbac86b0b47ddacc8deee7cd257e41de01cbe5c0
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a lot (many hundreds) of MAC or VLAN filters are added at one time,
we can overflow the Admin Queue buffer size with all the requests.
Unfortunately, the driver would then calculate the message size
incorrectly, causing it to be rejected by the PF. Furthermore, there was
no mechanism to trigger another request to allow for configuring the
rest of the filters that didn't fit into the first request.
To fix this, recalculate the correct buffer size when we detect the
overflow condition instead of just assuming the max buffer size. Also,
don't clear the request bit in adapter->aq_required when we have an
overflow, so that the rest of the filters can be processed later.
Change-ID: Idd7cbbc5af31315e0dcb1b10e6a02ad9817ce65c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up and enhance error messages related to VF MAC/VLAN filters.
Indicate which VF is having issues, and if possible indicate the MAC
address or VLAN involved.
Also, when an error is returned from the PF driver, print useful
information about what went wrong, for the most likely cases.
Change-ID: Ib3d15eef9e3369a78fd142948671e5fa26d921b8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a comment to the #endif to more easily match it with its #if.
Change-ID: I47eb0a60a17dc6d2f01a930e45006d2dc82e044f
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The watchdog only calls link_event not handle_link_event which means
that we need to save the old information in link_event.
Previously when polling we were comparing current data to the old data
saved the last time we actually received a link event. This means that
the polling would only fix link status changes in one direction
depending on what the last old data saved off was.
Change-ID: Ie590f30fdbcb133d0ddad4e07e3eb1aad58255b3
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When in NAPI with interrupts disabled, the HW needs to be forced to do a
write back on TX if the number of descriptors pending are less than a
cache line.
This stat helps keep track of how many times we get into this situation.
Change-ID: I76c1bcc7ebccd6bffcc5aa33bfe05f2fa1c9a984
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HW/NVM sets a limit of no less than 256 bytes for MSS. Stack can send as
low as 76 bytes MSS. This patch lowers the HW limit to 64 bytes to avoid
MDDs from firing and causing a reset when the MSS is lower than 256.
Change-ID: I36b500a6bb227d283c3e321a7718e0672b11fab0
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no need to kill the kernel thread here. If this condition was
true, the probe() would have died long before we got here. In any case,
we'll get the same result when this code tries to use the VSI pointer
being checked.
Prompted by a recent Linus diatribe.
Change-ID: I62f531cac34d4fc28ff9657d5b2d9523ae5e33a4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's really no reason to kill the kernel thread just because of a
little info string. This reworks the code to use snprintf's limiting to
assure that the string is never too long, and WARN_ON to still put out
a warning that we might want to look at the feature list length.
Prompted by a recent Linus diatribe.
Change-ID: If52ba5ca1c2344d8bf454a31bbb805eb5d2c5802
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no need to kill the thread and eventually the kernel in this
case. In fact, the remainder of the code won't hurt anything anyway,
so just complain that we're here and move along.
Prompted by a recent Linus diatribe.
Change-ID: Iec020d8bcfedffc1cd2553cc6905fd915bb3e670
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Code was moved into a separate function some time ago.
Change-ID: Icabbe71ce05cf5d716d3e1152cdd9cd41d11bcb5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The fm10k_msix_clean_rings function runs from hard interrupt context or
with interrupts already disabled in netpoll.
It can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code is pretty confused. The variable name 'bytes_not_copied'
clearly indicates that the programmer knew the semantics of
copy_{to,from}_user, but then the return value is checked for being
negative and used as a -Exxx return value.
I'm not sure this is the proper fix, but at least we get rid of the
dead code which pretended to check for access faults.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ixgbevf is loaded while the corresponding PF interface is down
and the driver assigns a random MAC address, that address can be
overwritten with the value of hw->mac.perm_addr, which would be 0 at
that point.
To avoid this case we init hw->mac.perm_addr to the randomly generated
address and do not set it unless we receive ACK from ixgbe.
Reported-by: John Greene <jogreene@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
replace some instances of memcpy for setting up the mac address with
ether_addr_copy()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Compiler complained of an unused variable, which the driver was just
using to store the result of a rd32 which is used to clear a register
unconditionally. Just drop the unused variable and re-use one.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Testing has now shown that the diagnostic code used with the CS4227
is no longer needed, so remove it.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_intr and ixgbe/ixgbevf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is the ixgbevf version of commit 8ac34f10a5 "ixgbe: Limit
lowest interrupt rate for adaptive interrupt moderation to 12K"
The same logic applies here as well as the same results since a netperf
test will starve for memory in the time from one Tx interrupt to the next.
As a result the ixgbevf driver underperformed when compared to vhost_net.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
KR auto-neg mode is what we will be using going forward. The SW
interface for this mode is different that what was used for iXFI.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit dfaf891dd3 ("ixgbe: Refactor the RSS configuration code")
introduced a few kernel-doc errors:
1) The function name is missing;
2) The format is wrong;
3) The short description is redundant.
Fix all the above for the correct execution of the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delete a redundant include of net/vxlan.h.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on hardware testing, the host interface supports up to 15368 bytes
as the maximum frame size. To determine the correct MTU, we subtract 8
for the internal switch tag, 14 for the L2 header, and 4 for the
appended FCS header, resulting in 15342 bytes of payload for our maximum
MTU on jumbo frames.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible that the PF has not yet assigned resources to the VF.
Although rare, this could result in the VF attempting to read queues it
does not own and result in FUM or THI faults in the PF. To prevent this,
check queue 0 before we continue in init_hw_vf.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
NAPI drivers no longer need to observe a particular protocol
to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y)
napi_hash_add() and napi_hash_del() are automatically called
from core networking stack, respectively from
netif_napi_add() and netif_napi_del()
This patch depends on free_netdev() and netif_napi_del() being
called from process context, which seems to be the norm.
Drivers might still prefer to call napi_hash_del() on their
own, since they might combine all the rcu grace periods into
a single one, knowing their NAPI structures lifetime, while
core networking stack has no idea of a possible combining.
Once this patch proves to not bring serious regressions,
we will cleanup drivers to either remove napi_hash_del()
or provide appropriate rcu grace periods combining.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was detected by Coverity.
The function skb_cow_head leaves skb alone on failure, so caller needs
to free.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The asm-generic changes for 4.4 are mostly a series from Christoph Hellwig
to clean up various abuses of headers in there. The patch to rename the
io-64-nonatomic-*.h headers caused some conflicts with new users, so I
added a workaround that we can remove in the next merge window.
The only other patch is a warning fix from Marek Vasut
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dQKG
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"The asm-generic changes for 4.4 are mostly a series from Christoph
Hellwig to clean up various abuses of headers in there. The patch to
rename the io-64-nonatomic-*.h headers caused some conflicts with new
users, so I added a workaround that we can remove in the next merge
window.
The only other patch is a warning fix from Marek Vasut"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: temporarily add back asm-generic/io-64-nonatomic*.h
asm-generic: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
gpio-mxc: stop including <asm-generic/bug>
n_tracesink: stop including <asm-generic/bug>
n_tracerouter: stop including <asm-generic/bug>
mlx5: stop including <asm-generic/kmap_types.h>
hifn_795x: stop including <asm-generic/kmap_types.h>
drbd: stop including <asm-generic/kmap_types.h>
move count_zeroes.h out of asm-generic
move io-64-nonatomic*.h out of asm-generic
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation of the number of multicast address for VF is not enough
for the large scale server with SR-IOV feature. IPv6 requires the multicast
MAC address for each IP address to handle the Neighbor Solicitation
message. We couldn't assign over 30 IPv6 addresses to a single VF.
This patch introduces the new mailbox API, IXGBE_VF_UPDATE_XCAST_MODE,
to update multicast mode of VF. This adds 3 modes;
- NONE only L2 exact match addresses or Flow Director enabled
- MULTI BAM and ROMPE set
- ALLMULTI BAM, ROMPE and MPE set
If a guest VF user wants over 30 MAC multicast addresses, set IFF_ALLMULTI
to request PF to update xcast mode to enable VF multicast promiscuous mode.
On the other hand, enabling VF multicast promiscuous mode may affect
security and performance in the network of the NIC. Only trusted VF can
enable multicast promiscuous mode. The behavior of untrusted VF is the
same as previous version.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implements the new netdev op to trust VF in ixgbe.
The administrator can turn on and off VF trusted by ip command which
supports trust message.
# ip link set dev eth0 vf 1 trust on
or
# ip link set dev eth0 vf 1 trust off
Send a ping to reset VF on changing the status of trusting.
VF driver will reconfigure its features on reset.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit 3092e5e4cc79 ("i40e: add little endian conversion for
checksum") fixed the checksum bug on big-endian architecture.
But we should not execute cpu_to_le16() unconditionally. Thus, put
cpu_to_le16() under certain condition.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In both i40e_calc_nvm_checksum() and i40e_update_nvm_checksum(), the
local variables designated by 'ret_code' are overwritten immediately. As
such, they should merely be declared.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i40evf_msix_aq(), the first two lines of rd32() are mainly to clear
the registers. If we initialize 'val' at this point, it will be
overwritten immediately. We shall simply discard the return value here.
When we initialize 'val', we might as well include the mask in one step.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following kernel-doc arguments for their respective functions are
missing:
1) @cd_type_cmd_tso_mss for i40e_tso();
2) @cd_type_cmd_tso_mss for i40e_tsyn();
3) @tx_ring for i40e_tx_enable_csum().
Add them all for the kernel-doc requirement.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
@flush has been missing since the inception of i40evf_irq_enable(). Add
it for the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using a custom approach change the code to use %*ph format
specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump up the version...
Change-ID: Ib8d501021671ba20250115ed54330e2c182255b7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a call to enable SR-IOV in the kernel failed, we need to disable
I40E_FLAG_VEB_MODE_ENABLED, so that bridge mode could fall back to
VEPA, which is a default.
Change-ID: I12b6f776769506db85b29bea94b9c88d0b5ee65e
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the driver output of the OEM
version string varied from the other tools. The mask value
and the order of operations were incorrect, per the original
change request. Without this patch, the version string will
appear incorrect from the driver.
Change-ID: Ie1ca6485284b4ce3b57e5a99b18b7641617c7ef7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem of possibly getting inconsistent flow control
statuses after a PF reset. Requested_mode was being set with a default
value during probing, but the initial HW state could be different from
this mode.
Change-ID: I772bf07b78616e87086418d4bd87954b66fa17cd
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Not sure how this compiles at all. Use the correct struct for
manipulating the VLAN filter list. Without this, the VLAN filter
list doesn't get processed correctly, and VLAN filters will not
be re-enabled after any kind of reset.
Change-ID: Iceff2dc089f303058fb71ecb08419eed471e0e90
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix i40e_is_vsi_uplink_mode_veb to check if bridge is actually
in VEB mode before allowing LB in the add VSI routine, instead of
unconditionally returning VEB bridge mode.
Change-ID: I162397b1bdd02367735fe9baaeb51465be2a3ce9
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new code flow requires us to grab the filter list lock before
adding/deleting the filter.
Change-ID: I4eaef508ab4da2d1b2e23f20f2a78d931d5b6aeb
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround to drop any flow control frames from being
transmitted from any VSI. FW can still send flow control frames if flow
control is enabled.
With this patch in place a malicious VF cannot send flow control or PFC
packets out on the wire.
Change-ID: I4303b24e98b93066d2767fec24dfe78be591c277
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was printing a message about not being able
to assign VMDq because of a lack of MSI-X vectors.
This was because a line was missing that initialized a variable,
simply a merge error.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code was setting up stats that were not being initialized.
This caused several counters to be displayed incorrectly, due
to indexing beyond the array of strings when printing stats.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-19
This series contains updates to i40e and i40evf only.
Kiran adds a spinlock around code accessing VSI MAC filter list to
ensure that we are synchronizing access to the filter list, otherwise
we can end up with multiple accesses at the same time which can cause
the VSI MAC filter list to get in an unstable or corrupted state.
Jesse fixes overlong BIT defines, where the RSS enabling call were
mistakenly missed. Also fixes a bug where the enable function was
enabling the interrupt twice while trying to update the two interrupt
throttle rate thresholds for Rx and Tx, while refactoring the IRQ
enable function to simplify reading the flow. Addressed the high
CPU utilization of some small streaming workloads that the driver should
reduce CPU in.
Anjali fixes two X722 issues with respect to EEPROM checksum verify and
reading NVM version info. Fixed where a mask value was accidentally
replaced with a bit mask causing Flow Director sideband to be broken.
Alex Duyck fixes areas of the drivers which run from hard interrupt
context or with interrupts already disabled in netpoll, so use
napi_schedule_irqoff() instead of napi_schedule().
Mitch fixes the VF drivers to not easily give up when it is not able
to communicate with the PF driver.
Carolyn fixes a problem where our tools MAC loopback test, after driver
unbind would fail because the hardware was configured for multiqueue and
unbind operation did not clear this configuration. Also fixed a issue
where the NVMUpdate tool gets bad data from the PHY when using the PHY
NVM feature because of contention on the MDIO interface from getting
PHY capability calls from the driver during regular operations.
Catherine fixed an issue where we were checking if autoneg was allowed
to change before checking if autoneg was changing, these checks need to
be in the reverse order.
Jean Sacren fixes up an function header comment to align the kernel-docs
with the actual code.
v2: Cleaned up the use of spin_is_locked() in patch 1 based on feedback
from David Miller, since it always evaluates to zero on uni-processor
builds
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
'err' would be overwritten immediately, so we should declare it only
rather than initialize it to zero.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The second argument name in the kernel-doc argument list for
i40e_features_check() was slightly off. Fix it for the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is an error coming back from get_phy_capabilities that does not
seem to have any functional implications. We will continue looking into
why this error message is occurring, but in the meantime, we will move it
to debug to avoid confusion.
Change-ID: I9091754bf62c066ddedeb249923d85606e2d68ed
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were previously checking if autoneg was allowed to change before
checking if autoneg was changing. We need to do this in the other order
or else we will erroneously return EINVAL when autoneg is not changing.
Change-ID: Iff9f7d1c9bddc1ad1e5d227d4f42754f90155410
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A mask value of 0x1FF was accidentally replaced with a bit mask
causing flow director sideband to be broken.
Change-ID: Id3387f67dd1b567b41692b570b383c58671e1eae
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the NVMUpdate Tool, when using the PHY
NVM feature, gets bad data from the PHY because of contention on the
MDIO interface from get PHY capability calls from the driver during
regular operations. The problem is fixed by adding a check if media
is available before calling get PHY capability function because that
bit is not set when device is in PHY interaction mode.
Change-ID: Ib89991b0f841808dd92410f5e8683d6ee3301cd0
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where our Tools MAC Loopback test, after
driver unbind would fail. This was because the hw was configured
for multiqueue and unbind operation did not clear this configuration.
The problem is fixed by resetting this configuration in i40e_remove.
Change-ID: I130c05138319182ed1476d3a0b5222d6a6320af9
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The adaptive ITR (interrupt throttle rate) algorithm was adjusting
the hardware's interrupt rate too frequently. This caused a lot
of variation in the interrupt rate for fairly constant workloads.
Change the code to have a counter and adjust only once every N
number of interrupts.
Change-ID: I0460f1f86571037484eca5aca36ac4d889cb8389
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The dynamic algorithm, while now working, doesn't have good
performance in 40G mode.
One part of this patch addresses the high CPU utilization of some small
streaming workloads that the driver should reduce CPU in.
It also changes the minimum ITR that the dynamic algorithm
will settle on, causing our minimum latency to go from 12us
to about 14us, when using adaptive mode.
It also changes the BULK interrupt rate to allow maximum throughput
on a 40Gb connection with a single thread of transmit, clamping
interrupt rate to 8000 for TX makes single thread traffic go too
slow.
The new ULTRA bulk setting is introduced and is used
when the Rx packet rate on this queue exceeds 40000 packets per
second. This value of 40000 was chosen because the automatic tuning
of minimum ITR=20us means that a single queue can't quite achieve
that many packets per second from a round-robin test.
Change-ID: Icce8faa128688ca5fd2c4229bdd9726877a92ea2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was using a value expressed in 2us increments
for the divisor to figure out our bytes/usec values.
Fix the usecs variable to contain a value in microseconds.
Change-ID: I5c20493103c295d6f201947bb908add7040b7c41
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves a multi-line register setting into a function
which simplifies reading the flow of the enable function.
This also fixes a bug where the enable function was enabling
the interrupt twice while trying to update the two interrupt
throttle rate thresholds for Rx and Tx.
Change-ID: Ie308f9d0d48540204590cb9d7a5a7b1196f959bb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VF driver is unable to communicate with the PF, it just gives
up and never tries again. Aside from the obvious character flaw that
this shows, it's also a lousy user experience.
When PF communications fail, wait five seconds, and try again. And
again. Don't give up, little VF driver! Your prince will come!
Change-ID: Ia1378a39879883563b8faffce819f375821f9585
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_intr and i40e/i40evf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acquire NVM, before issuing an AQ read nvm command for X722.
We need to acquire the NVM before issuing an AQ read to the NVM
otherwise we will get EBUSY from the FW. Also release when done.
This fixes the two X722 issues with respect to eeprom checksum verify
and reading NVM version info.
With this patch in place, i40e driver will provide basic support
for X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The defines from the RSS enabling call were mistakenly
missed in the patches to the i40e which should have been
to i40evf as well.
This is a follow up to (commit ed921559886dd40528) "fix
32 bit build warnings".
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a spinlock which is to be used for synchronizing
access to VSI's MAC filter list.
This patch also synchronizes execution of other codepaths which are
accessing VSI's MAC filter list with execution of
service_task:sync_vsi_filters.
In function i40e_add_vsi, copied out LAA MAC address instead of cloning
MAC filter entry because only MAC address is needed to remove MAC VLAN
filter from FW/HW.
Change-ID: I0e10ac7c715d44aa994239642aa4d57c998573a2
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With 64 VFs, we can easily overwhelm the AQ on the PF if we have too low
a limit on the number of AQ requests. This leads to ARQ overflow errors,
and occasionally VFs that fail to initialize.
Since we really only hit this condition on initial VF driver load, the
requests that we process are lightweight, so this extra work doesn't
cause problems for the PF driver.
Change-ID: I620221520d8af987df6ace9ba938ffaf22107681
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some devices, in some systems, in some configurations, the VFs would
fail to initialize the first time you loaded the driver.
To correct this, increase the delay time for the init task slightly, and
wait longer before giving up.
If we enable VFs and load the VF driver in the same kernel as the PF
driver, we can totally overwhelm the PF driver with AQ requests because
all of the instances try to initialize at the same time.
To help alleviate this, stagger the initial scheduling of the init task
using the PCIe function as a multiplier. We mask off the function to
only three bits so no instance has to wait too long.
With these two changes, initializing 128 VFs on a single device goes
from four minutes to just a few seconds.
Change-ID: If3d8720c1c4e838ab36d8781d9ec295a62380936
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1000Base_T_Optical got added to the function that figures out what
is supported when link is down but not when link is up. Add it in there
too so that we display the correct information.
Change-ID: I85ebcdfa7c02d898c44c673b1500552a53c8042e
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vlan_features field was correctly being set to the same value as the
netdev features field. However, this was being done before the features
were actually being set up, leaving the vlan_features empty.
Also, after a reset, vlan_features will be incorrectly assigned the
previous netdev feature flags, which can contain VLAN feature bits. This
makes the VLAN code angry and will cause a stack dump.
To fix these issues, set up the netdev features first, then mask out the
VLAN feature bits when assigning vlan_features.
Change-ID: Ib0548869dc83cf6a841cb8697dd94c12359ba4d2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the number of invalid messages from a VF is exceeded, the VF
will be disabled, due to the invalid messages. This happens if
other VF drivers (like DPDK) send a message through the driver's
mailbox (aka virtchannel) interface, but the message is not
supported by the i40e pf driver, such as CONFIG_PROMISCUOUS_MODE.
This patch changes the num_invalid_msgs in struct i40e_vf to record
the continuous invalid msgs, and it will be reset when a valid msg
is received.
Change-ID: Iaec42fd3dcdd281476b3518be23261dd46fc3718
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver. This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.
The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.
The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above
Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.
Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds support for setting a new bit in the Set Local LLDP MIB AQ command
Type field. When set to 1, the bit indicates to FW that Apps should be
treated as non-willing. When 0, FW behaves as before.
Change-ID: I0d2101c1606c59c7188d3e6a0c7810e0f205233a
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an ethtool priv flag to enable and disable printing
the VEB statistics.
Change-ID: I7654054a3a73b08aa8310d94ee8fce6219107dd8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Two defines that are not used are causing customer confusion - remove
them.
Change-ID: Icef0325aca8e0f4fcdfc519e026bdd375e791200
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow the nvmupdate application to decide when a read or write error
should be exposed to the user. Since the application needs to use
write probes to find the ReadOnly sections on a potentially unknown NVM
version in the HW and read probes to check the status of the last write,
some error messages are expected, but need not be shown to the users.
The driver doesn't know which are ignorable from real errors, so needs
to let the application make the decision.
Change-ID: I78fca8ab672bede11c10c820b83c26adfd536d03
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add const to functions that return strings that aren't going to be
modified. This addresses some reported compile complaints.
Change-ID: Ic56b1e814ab4d23a50480e7fdec652445f776ee8
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cut down on the number of startup log entries by putting a couple behind
debug flags and combining a couple others into a single line.
Change-ID: I708089f086308f84d43f8b6f0e8a634a02d058fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.
In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The polling routine for i40e was rounding up the budget for Rx cleanup to
1. This is incorrect as the netpoll poll call is expecting no Rx to be
processed as the budget passed was 0.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only call the internal_setup_link method when it is provided. This
check is required for newer version parts.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shorten up the delays in the init task, allowing the VF driver to
initialize faster. This aids performance in load/unload tests and
mitigates DMAR errors in VF enable/disable tests with absurdly short
delays. In the real world, the VF driver will come up more quickly.
The original values were set conservatively based on what we expected
from the firmware in terms of performance. Now that the driver is in use
and we know how well firmware responds to our requests, we can shorten
these delays.
Change-ID: Ibead77d34b19e8170e667c3f58bc14748bbc5bc9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save a little stack space and remove unnecessary strncpy() with a little
string pointer.
Change-ID: Id2719d34710bfc273d3bb445fec085cd04276e88
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 will report Gen 1x1 in the PCI config space as it is on
IOSF bus, so skip the PCI bus link/speed check.
Change-ID: Icd5f5751dc7fb00dccf0d5dc5a0a644948e7062e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store off reported PHY capabilities in link_info structure.
Change-ID: Ife0f037c26983ca985dbf79abf33f8f8791369e8
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a variable declaration inside an if block hiding an existing
declaration at the start of the function.
Also remove a forward function declaration that is no longer needed due
to code re-organization.
Change-ID: I12954668b722718074949c93d74cd20eaacd93e4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the flow-director-atr priv flag was added to our ethtool interface,
we don't need the on/off control in debugfs.
Change-ID: Ib3b599916434ab30ccd40074e71d7a81609b5bb5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Even though the device might be in MFP mode, if there's only one partition
enabled, then we still have plenty of interrupts for managing the Flow
Directory Sideband activity. This patch enables FD SB in this case.
This patch also reverses the sense of the conditional in order to remove
the negative logic.
Change-ID: I9edf211a6219fc8d159b4be9964f9fd7f4e00bc0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This version check only applies to very, very old firmware,
that only ran on A0 hardware, which we never shipped and don't
support in this driver anyway. Remove it, before somebody
gets hurt.
Change-ID: I3752d090ff488acf98ee76b075af961e9c968ee4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 has a way to work around the descriptor WB issue,
this offload helps turn that feature on.
Change-ID: I7ffa67622426bfca5a651417b63e3afcfeb60412
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Only the X722 device now supports 100M SGMII, and nothing supports
100M on 1000Base_T.
Change-ID: I6f44dcd818944edd40041410e6de380f4a359a0c
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are several error messages that have been printing when there is
no functional issue. These messages should be available at debug message
level only.
Change-ID: Id91e47bf942c483563995f30d8705fa53acd5aa3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some customers wish to be able to control our hardware specific
feature called flow director, at runtime. This patch enables
ethtool priv flags to control this driver/hardware specific feature.
ethtool --set-priv-flags ethX flow-director-atr off
NOTE: the ethtool ntuple interface controls the flow-director
sideband rules.
Change-ID: Iba156350b07fa2ce66f53ded51739f9a3781fe0e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add nlflags to the function comment for ndo_bridge_setlink.
Change-ID: I34c704f307f2a3f7bac3ca4b44e2a094d3d082d6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the reset never completes, it is necessary to retake the
semaphore before returning, because the caller will release
the semaphore.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch disables LRO by default in favor of GRO.
LRO is incompatible with forwarding and is disabled when forwarding
is turned on which makes the default offloads of the driver
inconsistent. LRO can still be enabled via ethtool.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These are not implementations of default architecture code but helpers
for drivers. Move them to the place they belong to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Check for actual value NETREG_UNINITIALIZED in case it ever changes from
the current value of zero.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that flow control packets initiated by the VF are
dropped and reported as spoofed.
Flow control packets can be used to limit the throughput or as DOS
attack when generated from a VF. Flow control is not supported per VF
hence any pause frames generated from a VF are considered malicious.
Also cleaned up indentation and some redundant comments.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused members in the PHY structure and add a new member to store
all the capabilities the PHY has as reported by the FW. This information
will help us determine what speeds the device is capable of when link is
down.
Also add an enum to decode the PHY types the NVM is capable of.
Use the phy_types variable to determine what phy types are possible
when link is down instead of device id as it will be more accurate.
When on a backplane device, we do not support changing any settings,
however we should display all the phy_types we are capable of so if we
see a backplane dev ID set supported and advertised purely based on
the phy_types variable.
Change-ID: Ia75d560f1fcd30c54cbfb7458690c5867559a930
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a module_types variable to the link_info struct to save the module
information from get_phy_capabilities. This information can be used to
determine which speeds the module supports.
Also add a new function update_link_info which updates the module_types
parameter and then calls get_link_info. This function should be called
in place of get_link_info so that the module_types variable stays
up-to-date with the rest of the link information.
The EAS table does not reflect the values that are actually returned,
so instead, basing these values on the Ethernet compliance codes
specified in table 33 of SFF-8436 as these have been accurate.
Use the new variable in ethtool to differentiate between a 10G/1G dual
speed fiber module and a 10G only module.
Change-ID: Ib7585cce321319c10ce15180054c41a6cbd41389
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to desires to write userland drivers, and other requests, without
needing the rest of the include files, the device ids are pulled out
into a standalone file.
Change-ID: Ic0b047dbf9d4b0891892309c1f2079f56d9b60e8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch moves the internal fw version and fw api version info to be
output in probe. The nvm version, etrack and oem version info are now
configured for output via ethtool -i.
Change-ID: I05d490093a7137dbefcdef263d014d1e5c9e83d0
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, the firmware may fail to allocate a VSI for a VF.
When this happens, the driver does not react well to the bad news and
has a panic attack.
To fix this problem, check the return value from i40e_alloc_vf_res and
don't try to configure the device further if it failed. Additionally,
explicitly clear the INIT bit when we free VF resources, so that this
bit will be in the proper state in the failure case, and won't blow up
elsewhere.
Change-ID: I6a20ce2b59c3458fd832032e88fa28cd42500189
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function call isn't needed here; the same function is already
called by i40e_reset_vf.
Change-ID: I96ccbf91b752965c9e28fe895d4c7d4c46e3ba44
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes the parsing of CEE App TLVs to fill in the App selector in struct
i40e_dcbx_config with the IEEE App selector so the caller doesn't have to
consider whether the App came from a CEE or IEEE DCBX negotiation.
Change-ID: Ia7d9d664cde04d2ebcc9822fd22e4929c6edab3a
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a member to the nvm_info struct for oem_ver info to be
output either by OID or ethtool.
Change-ID: I1e5d513ae67622e2af17042924fdb4b5d6d85366
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not correctly handling calls to its ndo_set_mac_address
method. It did not properly check to see if the override would be
allowed by the PF driver, and never removed the old address from its
filter list.
Add a new flag to the adapter struct which is set if the MAC address is
assigned by the PF. Check this flag and don't allow the MAC address to
be changed if it is set. Search for and properly remove the filter
for the old MAC address when the new one is set.
Change-ID: I817bf620c869c5a80e6a7eab65c9cbad1dc89799
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace one left over (1 << up) in the i40e_dcb.c file with the BIT()
macro.
Change-ID: I39492a400a2cee5ac566143a5b436cc478bea0db
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flag the filter_mask parameter as __always_unused in the
ndo_bridge_getlink function.
Change-ID: Ifc1e99c7fb84bcbf81cf7b0ac891ad8ca956ffb2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new Port link status bit and rename the link status to function
link status.
Change-ID: I71289327ae62638ce967b6ad40114caf998b6dab
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To help users and developers know what compile options
and hardware features are enabled at compile time, print
VxLAN is available.
Change-ID: I3162f3b7678dc725a597f964217920eb218b480b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF really doesn't care about the QOS handle but it will in the
future. Since the VF only uses TC0, send it that handle. On the VF
side, save the handle and use it to populate the QOS params when we call
into the client interface.
Change-ID: I76f41b070baeaa09b19383e9168bc677837e0761
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the capabilities passed to us by the PF driver to control VF driver
behavior. In the process, clean up the VLAN add/remove code so it's not
a horrible morass of ifdefs.
Change-ID: I1050eaf12b658a26fea6813047c9964163c70a73
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I found a code indent that was avoidable because a whole function is inside
an if block, reverse the if and move the code back a tab.
Change-ID: I9989c8750ee61678fbf96a3b0fd7bf7cc7ef300a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add missings spaces after declarations, remove another __func__ use,
remove uncessary braces, remove unneeded breaks, and useless returns,
and generally fix up some code.
Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using VFGEN_RSTAT to detect a VF reset is an endeavor that is fraught
with peril. It's entirely too easy to miss a reset because none of the
bits are sticky. By the time the VF driver reads the register, the reset
may have been processed and cleaned up by the PF driver, leaving the
register in the same state that it was before the reset.
Instead, detect a reset with the VF_ARQLEN register. When the VF is
reset, the enable bit in this register is cleared, and it stays cleared
until the VF driver processes the reset and re-enables the admin queue.
Because we now deal with multiple registers in the reset and watchdog
tasks, rename the rstat_val variable to reg_val.
Change-ID: Id1df17045c0992e607da0162d31807f7fc20d199
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes parsing of AQ command Get CEE DCBX OPER CFG (0x0A07). Change is
required because FW creates the oper_prio_tc nibbles reversed from those
in the CEE Priority Group sub-TLV.
Change-ID: I7d9d8641bb430d30e286fc3fac909866ef8a0de8
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ran into an issue where PF's VSI type list was different from VF's,
which was resulted in different enum index. The VSI type list can
be different depending on what build flag is used for PF and VF.
The change is to explicitly assign enum index for each VSI type
so that PF and VF always reference to the same VSI type event if the
enum lists are different.
Change-ID: I8c0e5fdb515f324f7964df863a458073cf467e57
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's been some need for controlling the periodic link polling for
debugging link issues. This patch enables switching it off and on
through an ethtool private flag. The link poll remains on by default,
but can be turned off with
ethtool --set-priv-flags p261p1 LinkPolling off
and later turned back on with
ethtool --set-priv-flags p261p1 LinkPolling on
To check the current status, use
ethtool --show-priv-flags p261p1
Change-ID: I32e4ab654ff3eec90a06cf144899971b82d71c40
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses an issue where multiple link up messages can be logged
resulting from aq link status timing when link properties are changed (fc,
speed, etc.); solved by using a single function to handle status printing
and adding a mechanism to track whether link state (up or down) has
actually changed.
Change-ID: Ied6ed6e49dc397c77d992adc0bc9ed3767152b9d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
