When PCI error is detected, in some architectures (like PowerPC) a slot
reset is performed - the driver's error handlers are in charge of "disable"
device before the reset, and re-enable it after a successful slot reset.
There are two cases though that another path is taken on the code: if the
slot reset is not successful or if too many errors already happened in the
specific adapter (meaning that possibly the device is experiencing a HW
failure that slot reset is not able to solve), the core PCI error mechanism
(called EEH in PowerPC) will remove the adapter from the system, since it
will consider this as a permanent failure on device. In this case, a path
is taken that leads to bnx2x_chip_cleanup() calling bnx2x_reset_hw(), which
then tries to perform a HW reset on chip. This reset won't succeed since
the HW is in a fault state, which can be seen by multiple messages on
kernel log like below:
bnx2x: [bnx2x_issue_dmae_with_comp:552(eth1)]DMAE timeout!
bnx2x: [bnx2x_write_dmae:600(eth1)]DMAE returned failure -1
After some time, the PCI error mechanism gives up on waiting the driver's
correct removal procedure and forcibly remove the adapter from the system.
We can see soft lockup while core PCI error mechanism is waiting for driver
to accomplish the right removal process.
This patch adds a verification to avoid a chip reset whenever the function
is in PCI error state - since this case is only reached when we have a
device being removed because of a permanent failure, the HW chip reset is
not expected to work fine neither is necessary.
Also, as a minor improvement in error path, we avoid the MCP information dump
in case of non-recoverable PCI error (when adapter is about to be removed),
since it will certainly fail.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-By: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit 087d7a8c91 "tg3: Fix for diasllow rx coalescing
time to be 0" disallow to set Rx coalescing time to be 0 as this stops
generating interrupts for the incoming packets. I found the zero
Tx coalescing time stops generating interrupts for outgoing packets
as well and fires Tx watchdog later. To avoid this, don't allow to set
Tx coalescing time to 0 and also remove subsequent checks that become
senseless.
Cc: satish.baddipadige@broadcom.com
Cc: siva.kallam@broadcom.com
Cc: michael.chan@broadcom.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we keep shadow copies of which interrupt sources are enabled
through the intrl2_*_mask_{set,clear} macros, make sure that the
ordering in which we do these two operations: update the copy, then
unmask the register is correct.
This is not currently a problem because we actually do not use them, but
we will in a subsequent patch optimizing register accesses, so better be
safe here.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ndo_set_rx_mode() is called for bnx2x, as part of process of
configuring the new MAC address filters [both unicast & multicast]
driver begins by flushing the existing configuration and then iterating
over the network device's list of addresses and configures those instead.
This has the side-effect of creating a short gap where traffic wouldn't
be properly classified, as no filters are configured in HW.
While for unicasts this is rather insignificant [as unicast MACs don't
frequently change while interface is actually running],
for multicast traffic it does pose an issue as there are multicast-based
networks where new multicast groups would constantly be removed and
added.
This patch tries to remedy this [at least for the newer adapters] -
Instead of flushing & reconfiguring all existing multicast filters,
the driver would instead create the approximate hash match that would
result from the required filters. It would then compare it against the
currently configured approximate hash match, and only add and remove the
delta between those.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't really change anything as BGMAC_CHIPCTL_1_IF_TYPE_RMII is
equal to 0. It make code a bit clener, so far when reading it one could
think we forgot to set a proper mode. It also keeps this mode code in
sync with other ones.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM53573 is a new series of Broadcom's SoCs. It's based on ARM and can
be found in two packages (versions): BCM53573 and BCM47189. It shares
some code with the Northstar family, but also requires some new quirks.
First of all there can be up to 2 Ethernet cores on this SoC. If that is
the case, they are connected to two different switch ports allowing some
more complex/optimized setups. It seems the second unit doesn't come
fully configured and requires some IRQ quirk.
Other than that only the first core is connected to the PHY. For the
second one we have to register fixed PHY (similarly to the Northstar),
otherwise generic PHY driver would get some invalid info.
This has been successfully tested on Tenda AC9 (BCM47189B0).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was failing on successful registration returning meaningless errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes: 55954f3bfd ("net: ethernet: bgmac: move BCMA MDIO Phy code into a separate file")
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove the wrong substraction from info->data in
tg3_get_rxnfc function. Without this patch, the number of RSS
queues reported is less by one.
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the rx coalescing time is 0, interrupts
are not generated from the controller and rx path hangs.
To avoid this rx hang, updating the driver to not allow
rx coalescing time to be 0.
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_get_platdata has failed pd is null.
Do not dereference a null pointer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5741X/5731X NPAR device IDs and dual media SFP/10GBase-T device IDs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are not enough resources to enable ntuple filtering,
log a warning message.
v2: Use single message and add missing newline.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the destination MAC address in the ntuple filter structure. The
current code assumes that the destination MAC address is always the MAC
address of the NIC. This may not be true if there are macvlans, for
example. Add destination MAC address checking and configure the filter
correctly using the correct index for the destination MAC address.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
txr->dev_state was not consistently manipulated with the acquisition of
the per-queue lock, after further inspection the lock does not seem
necessary, either the value is read as BNXT_DEV_STATE_CLOSING or 0.
Reported-by: coverity (CID 1339583)
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bridge device in NS2 has the same device ID as the ethernet controller.
Add check to avoid probing the bridge device.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate special vnic for dropping packets not matching the RX filters.
First vnic is for normal RX packets and the driver will drop all
packets on the 2nd vnic.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate napi for special vnic, packets arriving on this
napi will simply be dropped and the buffers will be replenished back
to the HW.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware is unable to drop rx packets not matching the RX filters. To
workaround it, we create a special VNIC and configure the hardware to
direct all packets not matching the filters to it. We then setup the
driver to drop packets received on this VNIC.
This patch creates the infrastructure for this VNIC, reserves a
completion ring, and rx rings. Only shared completion ring mode is
supported. The next 2 patches add a NAPI to handle packets from this
VNIC and the setup of the VNIC.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nitro A0 has a hardware bug in the rx path. The workaround is to create
a special COS context as a path for non-RSS (non-IP) packets. Without this
workaround, the chip may stall when receiving RSS and non-RSS packets.
Add infrastructure to allow 2 contexts (RSS and CoS) per VNIC. Allocate
and configure the CoS context for Nitro A0.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nitro is the embedded version of the ethernet controller in the North
Star 2 SoC. Add basic code to recognize the chip ID and disable
the features (ntuple, TPA, ring and port statistics) not supported on
Nitro A0.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing is decrementing the index "i" while we are cleaning up the
fragments we could not successful transmit.
Fixes: 9cde94506e ("bgmac: implement scatter/gather support")
Reported-by: coverity (CID 1352048)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4386f5662e ("net: ethernet: bcmgenet: use
phy_ethtool_{get|set}_link_ksettings")
This patch is wrong, the function phy_ethtool_{get|set}_link_ksettings
don't check if the device is running, but the driver bcmgenet need this
check.
The function {get|set}_settings need to access the mdio bus, and this
bus may only be used when the device is running. Otherwise, the clock
is disable and a mdio access will fail.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rc is not initialized so it can contain garbage if it is not
set by the call to bnxt_read_sfp_module_eeprom_info. Ensure
garbage is not returned by initializing rc to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcma portion of the driver has been split off into a bcma specific
driver. This has been mirrored for the platform driver. The last
references to the bcma core struct have been changed into a generic
function call. These function calls are wrappers to either the original
bcma code or new platform functions that access the same areas via MMIO.
This necessitated adding function pointers for both platform and bcma to
hide which backend is being used from the generic bgmac code.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bgmac driver is using the bcma provides device ID and revision, as
well as the SoC ID and package, to determine which features are
necessary to enable, reset, etc in the driver. In anticipation of
removing the bcma requirement for this driver, these must be changed to
not reference that struct. In place of that, each "feature" has been
given a flag, and the flags are enabled for their respective device and
SoC.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the BCMA MDIO phy into a separate file, as it is very tightly
coupled with the BCMA bus. This will help with the upcoming BCMA
removal from the bgmac driver. Optimally, this should be moved into
phy drivers, but it is too tightly coupled with the bgmac driver to
effectively move it without more changes to the driver.
Note: the phy_reset was intentionally removed, as the mdio phy subsystem
automatically resets the phy if a reset function pointer is present. In
addition to the moving of the driver, this reset function is added.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma buffer allocation, etc references a dma_dev device pointer from
the bcma core. In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct. Add a
dma_dev device pointer to the bgmac stuct and reference that instead.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bgmac_* print wrappers call dev_* prints with the dev pointer from
the bcma core. In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct. So,
simply change all of the bgmac_* prints to their dev_* counterparts. In
some cases netdev_* prints are more appropriate, so change those as
well.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code generates as static checker warning because htons(ETH_P_IPV6)
is always true. From the context it looks like the && was intended to
be !=.
Fixes: 94758f8de0 ('bnxt_en: Add GRO logic for BCM5731X chips.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allowable range is 0.25 seconds to 1 second interval. Default is
1 second.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is useful for multi-function devices.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a default VLAN, the VF has its own VLAN domain and it can receive
all traffic within that domain.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For correctness, the MRU enables bit must be set when passing the
MRU to firmware during vnic configuration.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to the Ethtool FLASHDEV command handler for additional
firmware types to cover all the on-chip processors.
Signed-off-by: Rob Swindell <rob.swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon successful mgmt processor firmware update, request a self
reset upon next PCIe reset (e.g. system reboot).
Signed-off-by: Rob Swindell <rob.swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support Secure Firmware Update, we must be able to allocate
a staging area in the Flash. This patch adds support for the
"update" type to tell firmware to do that.
Signed-off-by: Rob Swindell <rob.swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling the firmware to do function reset on the PF will kill all the VFs.
To prevent that, we call function reset on the 1st PF open before any VF
can be activated. On subsequent PF opens (with possibly some active VFs),
a bit has been set and we'll skip the function reset. VF driver will
always do function reset on every open. If there is an AER event, we will
always do function reset.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 for doing nothing is confusing to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64bits kernels, device stats are 64bits wide, not 32bits.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
bgmac_open() calls phy_start() to initialize the PHY state machine,
which will set the interface's carrier state accordingly, no need to
force that as this could be conflicting with the PHY state determined by
PHYLIB.
Fixes: dd4544f054 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not start the transmit queue in bgmac_open(). If the
queue was stopped prior to closing then re-opening the interface, we
would never be able to wake-up again.
Fixes: dd4544f054 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are checking for the Start of Frame bit in the ctl1 word, while this
bit is set in the ctl0 word instead. Read the ctl0 word and update the
check to verify that.
Fixes: 9cde94506e ("bgmac: implement scatter/gather support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port number for GENEVE is hard coded into the bnxt driver. This is the
kind of thing we want to avoid going forward. For now I will integrate
this back into the port notifier so that we can change the GENEVE port
number if we need to in the future.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ends up doing several things. First it updates the driver to
make use of the new unified UDP tunnel offload notifier functions. In
addition I updated the code so that we can work around the bits that were
checking for if VXLAN was enabled since we are now using a notifier based
setup.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
I also went through and dropped the BNX2X VXLAN and GENEVE specific build
flags.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fully support 25G and 50G link settings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some cards do not support autoneg. The current code does not prevent the
user from enabling autoneg with ethtool on such cards, causing confusion.
Firmware provides the autoneg capability information and we just need to
store it in the support_auto_speeds field in bnxt_link_info struct.
The ethtool set_settings() call will check this field before proceeding
with autoneg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bnxt_gro_func_5731x() to handle GRO packets for this chip. The
completion structures used in the new chip have new data to help determine
the header offsets. The offsets can be off by 4 if the packet is an
internal loopback packet (e.g. from one VF to another VF). Some additional
logic is added to adjust the offsets if it is a loopback packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer chips require different logic to handle GRO packets. So refactor
the code so that we can call different functions depending on the chip.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define all the supported chip numbers and chip categories. Store the
chip_num returned by firmware. If the call to get the version and chip
number fails, we should abort.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NPAR type is read from bnxt_hwrm_func_qcfg. Do not allow changing link
parameters if in NPAR mode sinc ethe port is shared among multiple
partitions. The link parameters are set up by firmware.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF driver gets this event, the VF configuration has changed (such
as default VLAN). The VF driver will initiate a silent reset to pick up
the new configuration.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a default VLAN is added to the VF, the VF driver needs to reset to
pick up the default VLAN ID. We can use the same tx timeout reset logic
to do that, without the debug output. This new function, with the
silent parameter to suppress debug output will now serve both purposes.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF can setup a default VLAN for a VF. The default VLAN tag is
automatically inserted and stripped without the knowledge of the
stack running on the VF. The VF driver needs to know that default
VLAN is enabled as VLAN acceleration on the RX side is no longer
supported. Call netdev_update_features() to fix up the VLAN features
as necessary. Also, VLAN strip mode must be enabled to strip out
the default VLAN tag.
Only allow VF default VLAN to be set if the firmware spec is >= 1.2.1.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few netdev statistics to report transmitted and received bytes and
packets and a few obvious errors.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the statistics from the BGMAC's builtin MAC and return them to
user-space using the standard ethtool helpers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing different helpers to be utilized against
network devices created by the bgmac driver, make sure that we bind the
net_device with core->dev.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both CTAG and STAG rx acceleration must be enabled together, we
only need to check one feature flag (NETIF_F_HW_VLAN_CTAG_RX) before
calling __vlan_hwaccel_put_tag().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can only be set to strip or not strip both the VLAN CTAG and
STAG. It cannot strip one and not strip the other. Add logic to
bnxt_fix_features() to toggle both feature flags when the user is toggling
one of them.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the is_push flag in the software BD before the tx data is pushed to
the chip. It is possible to get the tx interrupt as soon as the tx data
is pushed. The tx handler will not handle the event properly if the
is_push flag is not set and it will crash.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since implementing VLAN filtering in commit 05cc5a39dd
("bnx2x: add vlan filtering offload") bnx2x refuses to add a VLAN while
the interface is down:
# ip link add link enp3s0f0 enp3s0f0_10 type vlan id 10
RTNETLINK answers: Bad address
and in dmesg (with bnx2x.debug=0x20):
bnx2x: [bnx2x_vlan_rx_add_vid:12941(enp3s0f0)]Ignoring VLAN
configuration the interface is down
Other drivers have no problem with this.
Fix this peculiar behavior in the following way:
- Accept requests to add/kill VID regardless of the device state.
Maintain the requested list of VIDs in the bp->vlan_reg list.
- If the device is up, try to configure the VID list into the hardware.
If we run out of VLAN credits or encounter a failure configuring an
entry, fall back to accepting all VLANs.
If we successfully configure all entries from the list, turn the
fallback off.
- Use the same code for reconfiguring VLANs during NIC load.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_init_bp() allocates memory with bnx2x_alloc_mem_bp() so if we
fail later in bnx2x_init_one() we need to free this memory
with bnx2x_free_mem_bp() to avoid leakages. E.g. I'm observing memory
leaks reported by kmemleak when a failure (unrelated) happens in
bnx2x_vfpf_acquire().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the weaker but more appropriate dma_rmb() to order the reading of
the completion ring.
Suggested-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code is more complicated than necessary and can only report
unsupported SFP+ module if it is plugged in after the device is up.
Rename bnxt_port_module_event() to bnxt_get_port_module_status(). We
already have the current module_status in the link_info structure, so
just check that and report any unsupported SFP+ module status. Delete
the unnecessary last_port_module_event. Call this function at the
end of bnxt_open to report unsupported module already plugged in.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The len value in the hwrm error message is wrong. Use the properly adjusted
value in the variable len.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code has 2 problems:
1. The maximum wait time is not long enough. It is about 60% of the
duration specified by the firmware. It is calling usleep_range(600, 800)
for every 1 msec we are supposed to wait.
2. The granularity of the delay is too coarse. Many simple firmware
commands finish in 25 usec or less.
We fix these 2 issues by multiplying the original 1 msec loop counter by
40 and calling usleep_range(25, 40) for each iteration.
There is also a second delay loop to wait for the last DMA word to
complete. This delay loop should be a very short 5 usec wait.
This change results in much faster bring-up/down time:
Before the patch:
time ip link set p4p1 up
real 0m0.120s
user 0m0.001s
sys 0m0.009s
After the patch:
time ip link set p4p1 up
real 0m0.030s
user 0m0.000s
sys 0m0.010s
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports 4K/8K/64K page sizes for the rings and we try to
match it to the CPU PAGE_SIZE. The current page size limits for the rings
are based on 4K/8K page size. If the page size is 64K, these limits are
too large. Reduce them appropriately.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to log a message during driver load indicating PCIe link
speed and width.
The log message will look like this:
bnxt_en 0000:86:00.0 eth0: PCIe: Speed 8.0GT/s Width x8
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command. We support SFP+ and QSFP
modules.
v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set
max channel parameters are shown incorrectly in ethtool -l. With only 1
vector, bnxt_get_max_rings() will return -ENOMEM. bnxt_get_channels
should check this return value, and set max_rx/max_tx to 0 if it is
non-zero.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Add detection and recovery code when the hardware returned opaque value
does not match the expected consumer index. Once the issue is detected,
we skip the processing of all RX and LRO/GRO packets. These completion
entries are discarded without sending the SKB to the stack and without
producing new buffers. The function will be reset from a workqueue.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a rare hardware bug that can cause a bad opaque value in the RX
or TPA completion. When this happens, the hardware may have used the
same buffer twice for 2 rx packets. In addition, the driver will also
crash later using the bad opaque as the index into the ring.
The rx opaque value is predictable and is always monotonically increasing.
The workaround is to keep track of the expected next opaque value and
compare it with the one returned by hardware during RX and TPA start
completions. If they miscompare, we will not process any more RX and
TPA completions and exit NAPI. We will then schedule a workqueue to
reset the function.
This patch adds the logic to keep track of the next rx consumer index.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently had a system crash in the cnic module. Vmcore analysis confirmed
that "ip link up" was executed which failed due to an allocation failure
because of memory fragmentation. Futher analysis revealed that the cnic irq
vector was still allocated after the "ip link up" that failed. When
"ip link down" was executed it called free_msi_irqs() which crashed the system
because the cnic irq was still inuse.
PANIC: "kernel BUG at drivers/pci/msi.c:411!"
The code execution was:
cnic_netdev_event()
if (event == NETDEV_UP) {
.
.
▹ if (!cnic_start_hw(dev))
cnic_start_hw()
calls cnic_cm_open() which failed with -ENOMEM
cnic_start_hw() then took the err1 path:
err1:↩
cp->free_resc(dev);↩ <---- frees resources but not irq vector
pci_dev_put(dev->pcidev);↩
return err;↩
}↩
This returns control back to cnic_netdev_event() but now the cnic irq vector
is still allocated even although cnic_cm_open() failed. The next
"ip link down" while trigger the crash.
The cnic_start_hw() routine is not handling the allocation failure correctly.
Fix this by checking whether CNIC_DRV_STATE_HANDLES_IRQ flag is set indicating
that the hardware has been started in cnic_start_hw(). If it has then call
cp->stop_hw() which frees the cnic irq vector and cnic resources. Otherwise
just maintain the previous behaviour and free cnic resources.
I reproduced this by injecting an ENOMEM error into cnic_cm_alloc_mem()s return
code.
# ip link set dev enpX down
# ip link set dev enpX up <--- hit's allocation failure
# ip link set dev enpX down <--- crashes here
With this patch I confirmed there was no crash in the reproducer.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multicast/all-multicast internal flags are not properly restored
after device reset. This could lead to unreliable multicast operations
after an ethtool configuration change for example.
Call bnxt_mc_list_updated() and setup the vnic->mask in bnxt_init_chip()
to fix the issue.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code determines if the next ring entry is valid before proceeding
further to read the rest of the entry. The CPU can re-order and read
the rest of the entry first, possibly reading a stale entry, if DMA
of a new entry happens right after reading it. This issue can be
readily seen on a ppc64 system, causing it to crash.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch assumes that the bnxt hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP and GRE headers.
I have been told by Michael Chan that this is working. Though this might
be somewhat redundant for IPv6 as they are forcing the checksum to be
computed for all IPv6 frames that are offloaded. A follow-up patch may be
necessary in order to fix this as it is essentially mangling the outer IPv6
headers to add a checksum where none was requested.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE, that means the native CPU
page is bigger than the maximum length of the RX BD. Divide the page
into multiple 32K buffers for the aggregation ring.
Add an offset field in the bnxt_sw_rx_agg_bd struct to keep track of the
page offset of each buffer. Since each page can be referenced by multiple
buffer entries, call get_page() as needed to get the proper reference
count.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX BD length field of this device is 16-bit, so the largest buffer
size is 65535. For LRO and GRO, we allocate native CPU pages for the
aggregation ring buffers. It won't work if the native CPU page size is
64K or bigger.
We fix this by defining BNXT_RX_PAGE_SIZE to be native CPU page size
up to 32K. Replace PAGE_SIZE with BNXT_RX_PAGE_SIZE in all appropriate
places related to the rx aggregation ring logic.
The next patch will add additional logic to divide the page into 32K
chunks for aggrgation ring buffers if PAGE_SIZE is bigger than
BNXT_RX_PAGE_SIZE.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only MSI-X can be used on a VF. The driver should fail initialization
if it cannot successfully enable MSI-X.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
By using napi_complete_done(), we allow fine tuning of
/sys/class/net/ethX/gro_flush_timeout for higher GRO aggregation
efficiency for a Gbit NIC.
Check commit 24d2e4a507 ("tg3: use napi_complete_done()") for details.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both bcm_sysport_tx_isr() and bcm_sysport_rx_isr() run in hard irq
context, we do not need to block irq again.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64bit kernels, device stats are 64bit wide, not 32bit.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only core revisions older than 4 use BGMAC_CMDCFG_SR_REV0. This mainly
fixes support for BCM4708A0KF SoCs with Ethernet core rev 5 (it means
only some devices as most of BCM4708A0KF-s got core rev 4).
This was tested for regressions on BCM47094 which doesn't seem to care
which bit gets used.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes Ethernet on D-Link DIR-885L with BCM47094 SoC. Felix reported
similar fix was needed for his BCM4709 device (Buffalo WXR-1900DHP?).
I tested this for regressions on BCM4706, BCM4708A0 and BCM47081A0.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Byte Queue Limits (BQL) support to bcmgenet driver.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_isr1() and bcmgenet_isr0() run in hard irq context,
we do not need to block irq again.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using napi_complete_done(), we allow fine tuning
of /sys/class/net/ethX/gro_flush_timeout for higher GRO aggregation
efficiency for a Gbit NIC.
Check commit 24d2e4a507 ("tg3: use napi_complete_done()") for details.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petri Gynther <pgynther@google.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some dual port cards, link speeds on both ports have to be compatible.
Firmware will inform the driver when a certain speed is no longer
supported if the other port has linked up at a certain speed. Add
logic to handle this event by logging a message and getting the
updated list of supported speeds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hypervisors (e.g. ESX) require the VF MAC address to be forwarded to
the PF for approval. In Linux PF, the call is not forwarded and the
firmware will simply check and approve the MAC address if the PF has not
previously administered a valid MAC address for this VF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let firmware know that the driver is giving up control of the link so that
it can be shutdown if no management firmware is running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10GBaseT devices must autonegotiate to determine master/slave clocking.
Disallow forced speed in ethtool .set_settings() for these devices.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dmadesc_set() is used for setting the Tx buffer DMA address, length,
and status bits on a Tx ring descriptor when a frame is being Tx'ed.
Always set the Tx buffer DMA address first, before updating the length
and status bits, i.e. giving the Tx descriptor to the hardware.
The reason this is a cleanup rather than a fix is that the hardware
won't transmit anything from a Tx ring until the TDMA producer index
has been incremented. As long as the dmadesc_set() writes complete
before the TDMA producer index write, life is good.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add frag_size = skb_frag_size(frag) and use it when needed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Readability: Move nr_frags assignment a few lines down in order
to bundle index -> ring -> txq calculations together.
2. Readability: Add parentheses around nr_frags + 1.
3. Minor fix: Stop the Tx queue and throw the error message only if
the Tx queue hasn't already been stopped.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If autoneg is off, we should always report the speed and duplex settings
even if it is link down so the user knows the current settings. The
unknown speed and duplex should only be used for autoneg when link is
down.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that the forced speed is a valid speed supported by firmware.
If not supported, return -EINVAL.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the PORT_CONN_NOT_ALLOWED async event handling logic. The driver
will print an appropriate warning to reflect the SFP+ module enforcement
policy done in the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver only sets bit 0 of the async_event_fwd fields.
To be compatible with the latest spec, we need to set the
appropriate event bits handled by the driver. We should be handling
link change and PF driver unload events, so these 2 bits should be
set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users to get|set EEE parameters.
v2: Added comment for preserving the tx_lpi_timer value in get_eee.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add bnxt_hwrm_set_eee() function to setup EEE firmware parameters based
on the bp->eee settings.
2. The new function bnxt_eee_config_ok() will check if EEE parameters need
to be modified due to autoneg changes.
3. bnxt_hwrm_set_link() has added a new parameter to update EEE. If the
parameter is set, it will call bnxt_hwrm_set_eee().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get EEE capability and the initial EEE settings from firmware.
Add "EEE is active | not active" to link up dmesg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new AUTONEG_PAUSE bit in the new interface to better
control autoneg flow control settings, independent of RX and TX
advertisement settings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new field names in API structs and stop using deprecated fields
auto_link_speed and auto_duplex in phy_cfg/phy_qcfg structs.
Update copyright year to 2016.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To report flow control tx/rx settings accurately regardless of autoneg
setting, we should use link_info->req_flow_ctrl. Before this patch,
the reported settings were only correct when autoneg was on.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The typo caused the wrong flow control bit to be set.
Reported by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of every padded firmware message is specified in the first
HWRM_VER_GET response message. Use this value to pad every message
after that.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing code does the following:
allocate completion ring
initialize completion ring doorbell
disable interrupts on this completion ring by writing to the doorbell
We can have a race where firmware sends an asynchronous event to the host
after completion ring allocation and before doorbell is initialized.
When this happens driver can crash while ringing the doorbell using
uninitialized value as part of handling the IRQ/napi request.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_len needs to be skb_headlen(skb) in bcmgenet_xmit_single().
Fragmented skbs can have only Ethernet + IP + TCP headers (14+20+20=54 bytes)
in the linear buffer, followed by the rest in fragments. Bumping skb_len to
ETH_ZLEN would be incorrect for this case, as it would introduce garbage
between TCP header and the fragment data.
This also works with regular/non-fragmented small packets < ETH_ZLEN bytes.
Successfully tested this on GENETv3 with 42-byte ARP frames.
For testing, I used:
ethtool -K eth0 tx-checksum-ipv4 off
ethtool -K eth0 tx-checksum-ipv6 off
echo 0 > /proc/sys/net/ipv4/tcp_timestamps
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add bytes_compl local variable to __bcmgenet_tx_reclaim() to collect
transmitted bytes. dev->stats updates can then be moved outside the
while-loop. bytes_compl is also needed for future BQL support.
2. When bcmgenet device uses Tx checksum offload, each transmitted skb
gets an extra 64-byte header prepended to it. Before this header is
prepended to the skb, we need to save the skb "wire" length in
GENET_CB(skb)->bytes_sent, so that proper Tx bytes accounting can
be done in __bcmgenet_tx_reclaim().
3. skb->len covers the entire length of skb, whether it is linear or
fragmented. Thus, when we clean the fragments, do not increase
transmitted bytes.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When un-mapping skb->data in __bcmgenet_tx_reclaim(),
we must use the length that was used in original dma_map_single(),
instead of skb->len that might be bigger (includes the frags)
We simply can store skb_len into tx_cb_ptr->dma_len and use it
at unmap time.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all adapters have FC-NPIV configured. If bnx2fc is used with such an
adapter, driver would read irrelevant data from the the nvram and log
"FC-NPIV table with bad length..." In system logs.
Simply accept that reading '0' as the feature offset in nvram indicates
the feature isn't there and return.
Reported-by: Andrew Patterson <andrew.patterson@hpe.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver has hit a parity event, HW can no longer write to host memory.
As a result, Tx completions cannot be written to the host SB memory, and
waiting for Tx completions eventually timeout.
As driver is willing to delay as much as 1-2 seconds per Tx queue for its
draining and this delay is sequential, the time to recover might greatly
lengthen needlessly in case the recovery is done under multi-connection
traffic.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pci_error_handler callbacks to support for pcie advanced error
recovery.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the more useful port statistics in ethtool -S for the PF device.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include some of the port error counters (e.g. crc) in ->ndo_get_stats64()
for the PF device.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gather periodic port statistics if the device is PF and link is up. This
is triggered in bnxt_timer() every one second to request firmware to DMA
the counters.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow all autoneg speeds aupported by firmware to be advertised. If
the advertising parameter is 0, then all supported speeds will be
advertised.
Remove BNXT_ALL_COPPER_ETHTOOL_SPEED which is no longer used as all
supported speeds can be advertised.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The supported bits and advertising bits in ethtool have the same
definitions. The same is true for the firmware bits. So use the
common function to handle the conversion for both supported and
advertising bits.
v2: Don't use parentheses on function return.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And report actual pause settings to ETHTOOL_GPAUSEPARAM to let ethtool
resolve the actual pause settings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the conversion of pause bits and add one extra call layer so
that the same refactored function can be reused to get the link partner
advertisement bits.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
